AirPair-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for AirPair-MIB.
571
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
571 total| Object Name |
|---|
org OBJECT IDENTIFIER .1.3 |
SNMPv2-MIB Unknown .1.3 |
dod OBJECT IDENTIFIER .1.3.6 |
internet OBJECT IDENTIFIER .1.3.6.1 |
private OBJECT IDENTIFIER .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
dragonwave OBJECT IDENTIFIER .1.3.6.1.4.1.7262 |
airPair OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1 |
apResetSystemWriting '1' to this object resets the NIC, Modem, and radio.rw INTEGER ( 0 .. 1 ) .1.3.6.1.4.1.7262.1.1 |
apSaveMIBWriting '1' to this object save all MIB values. Note: If the AirPair type is
'airpair120' or 'airpair170' and the radio band doesn't match the AirPair type,
Mib can't be saved.rw Enumeration .1.3.6.1.4.1.7262.1.2 |
apAdminStatusNOT IMPLEMENTED
The desired state of the system. 'testing' and 'down' indicates that no user
packet data can be passed.'down' disables the transmitter, while 'testing'
does not.'up' enables the transmitter.rw Enumeration .1.3.6.1.4.1.7262.1.3 |
apOperStatusThe current operational state of the system.
Testing indicates that no operational packets can be passed.ro Enumeration .1.3.6.1.4.1.7262.1.4 |
apAirInterfaceEncryptionOBSOLETE. This enables encryption on the air interface.ro Enumeration .1.3.6.1.4.1.7262.1.5 |
apMibVersionNumberThe version number of the MIB.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.6 |
apTypeIndicates the specific type of system this is.ro Enumeration .1.3.6.1.4.1.7262.1.7 |
apSpeedChanges the working speed of the Airpair.
Writes are only valid if system is a FLEX. Due to backwards compatibility issue, 0 value should
be treated as 0 Mbps.rw Enumeration .1.3.6.1.4.1.7262.1.8 |
apMaxSpeedIndicates the maximum speed that this system can operate at. Due to backwards compatibility issue, 0 value should
be treated as 0 Mbps.ro Enumeration .1.3.6.1.4.1.7262.1.9 |
apKeyEnter your AirPairFLEX key here along with the maximum speed for
that key to upgrade the FLEX system.
Format: [speed] [key]
Example: 50 abc123rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.10 |
apAuthentication OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.11 |
uniquePeerAuthenticationKeyThe serial number of the peer node that this node will communicate with.
This is only used when authentication mode is set to unique.rw DisplayString ( SIZE ( 0 .. 34 ) ) .1.3.6.1.4.1.7262.1.11.1 |
peerDetectedSerialNumberThe serial number of the peer node that the system is presently communicating
with. This is only used when authentication is set to unique.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.11.2 |
authenticationModeThis sets the authentication mode for the system.If configured for unique
authentication, an AIRPAIR node only exchanges user traffic with one other
AIRPAIR node. The serial number is used in this case.
If configured for group authentication, an AIRPAIR node exchanges user
traffic with another AIRPAIR node of the same group and uses the
authentication keys.rw Enumeration .1.3.6.1.4.1.7262.1.11.3 |
authenticationFailureActionThis sets the authentication failure action for the system.
Block traffic will block all user traffic including remote
management access. Pass traffic will allow all user traffic
to be sent and recievedrw Enumeration .1.3.6.1.4.1.7262.1.11.4 |
peerAuthenticationStatusSpecifies the current authentication status of the system.
Authenticated means authentication is on and the system
has been authenticated, notAuthenticated means authentication
is off or the system has not communicated yet with the other node,
explicit authentication failure means authentication is on and
authentication has failedro Enumeration .1.3.6.1.4.1.7262.1.11.5 |
apNetworkInterfaceCard OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.12 |
networkInterfaceDescA textual string containing information about the modem.
Includes the manufacturer, product name, software
version, and hardware version of the modem card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.12.1 |
ipAddressThe IP Address of the network interface card.ro IpAddress .1.3.6.1.4.1.7262.1.12.2 |
subnetMaskThe subnet mask for the network interface card.ro IpAddress .1.3.6.1.4.1.7262.1.12.3 |
defaultGatewayThe default gateway for the network interface cardro IpAddress .1.3.6.1.4.1.7262.1.12.4 |
autoNegotiationSetupTurns auto-negotiation on or off. Turning off results in
the interface defaulting to 100BaseT, Full Duplex.rw Enumeration .1.3.6.1.4.1.7262.1.12.5 |
negotiatedLinkParametersDisplays the Interface card current operating negotiated
parameters.ro Enumeration .1.3.6.1.4.1.7262.1.12.6 |
minimumNegotiableLinkParametersDisplays the minimum negotiable parameter set for the enet
interface.ro Enumeration .1.3.6.1.4.1.7262.1.12.7 |
serialNumberThe Serial number of the network interface card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.12.8 |
snmpSetRequestsIndicates whether SNMP SET requests are allowed.ro Enumeration .1.3.6.1.4.1.7262.1.12.9 |
httpAccessModeNOT IMPLEMENTED
Indicates whether HTTP access is allowed.rw Enumeration .1.3.6.1.4.1.7262.1.12.10 |
telnetAccessModeIndicates whether Telnet access is allowed.rw Enumeration .1.3.6.1.4.1.7262.1.12.11 |
dnsServerNOT IMPLEMENTED
Indicates the DNS for the system.rw IpAddress .1.3.6.1.4.1.7262.1.12.12 |
vlanTaggingIndicates whether VLAN tagging is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.12.13 |
vlanTagThe first two bytes are set to 0x8100. The two byte
control tag is set by the user.rw DisplayString ( SIZE ( 8 ) ) .1.3.6.1.4.1.7262.1.12.14 |
nicStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.12.15 |
nicFramesInThe current count of NIC frames received.ro Counter .1.3.6.1.4.1.7262.1.12.15.1 |
nicFramesOutThe current count of NIC frames sent.ro Counter .1.3.6.1.4.1.7262.1.12.15.2 |
nicFramesInErrorThe current count of NIC frames received in error.ro Counter .1.3.6.1.4.1.7262.1.12.15.3 |
nicUndersizedFramesInThe current count of undersized NIC frames received.ro Counter .1.3.6.1.4.1.7262.1.12.15.4 |
nicOversizedFramesInThe current count of oversized NIC frames received.ro Counter .1.3.6.1.4.1.7262.1.12.15.5 |
nicFramesInQueue1DiscardedThe current count of NIC frames received in queue 2 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.1.12.15.6 |
nicFramesInQueue2DiscardedThe current count of NIC frames received in queue 2 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.1.12.15.7 |
nicFramesInQueue1The current count of NIC frames passed through queue 1.ro Counter .1.3.6.1.4.1.7262.1.12.15.8 |
nicFramesInQueue2The current count of NIC frames passed through queue 2.ro Counter .1.3.6.1.4.1.7262.1.12.15.9 |
nicFramesInQueue3The current count of NIC frames passed through queue 3.ro Counter .1.3.6.1.4.1.7262.1.12.15.10 |
nicFramesInQueue4The current count of NIC frames passed through queue 4.ro Counter .1.3.6.1.4.1.7262.1.12.15.11 |
nicFramesInQueue3DiscardedThe current count of NIC frames received in queue 3 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.1.12.15.12 |
nicFramesInQueue4DiscardedThe current count of NIC frames received in queue 4 that
were discarded, but due to an error. One possible reason
is lack of buffer space.ro Counter .1.3.6.1.4.1.7262.1.12.15.13 |
maxFrameSizeThe default maximum frame size is 1600 bytes. The settable
maximum frame size must be a multiple of 128. If the chosen
maximum frame size is not a multiple of 128, its closest
number which is a multiple of 128 is actually used. The
settable lowest maximum frame size is 1664, and the settable
highest maximum frame size is 9600. If the chosen maximum
frame size is out of this range, the default maximum frame
size of 1600 is used.rw INTEGER ( 1600..9600 ) .1.3.6.1.4.1.7262.1.12.16 |
pauseFrameEnableWhen PAUSE is enabled, pause frames can be generated by the
system and the pause frames will flow toward the link partner
on the network. When PAUSE is enabled,
Qos is disabled automatically. When PAUSE is not enabled,
no pause frames will be generated by the system.rw Enumeration .1.3.6.1.4.1.7262.1.12.17 |
opticalTransmitterStateWhen it is on, optical transmitter is enabled. Otherwise
optical transmitter is disabled.rw Enumeration .1.3.6.1.4.1.7262.1.12.18 |
apIntermediateFrequencyCard OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.13 |
intermediateFrequencyDescA textual string containing information about the modem.
Includes the manufacturer, product name, software
version, and hardware version of the modem card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.13.1 |
ifTxSynthesizerLockIndicates if the transmit synthesizer is locked.ro Enumeration .1.3.6.1.4.1.7262.1.13.2 |
ifRxSynthesizerLockIndicates if the receive synthesizer is locked.ro Enumeration .1.3.6.1.4.1.7262.1.13.3 |
apFrequencies OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.14 |
frequencyTypeThe radio frequency standard used in the system.
Frequency bands are divided into sub bands.
ie FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and
fcc23d which make up the entire FCC23 bandrw Enumeration .1.3.6.1.4.1.7262.1.14.1 |
freqGroupSelectedThe frequency group selected for the system.
The frequency subbands are divided into frequency groups txHigh
and txLow. An AIRPAIR system must have one node configured to
txLow and the other node configure to txHighrw Enumeration .1.3.6.1.4.1.7262.1.14.2 |
txHighFreqTableA table of txHigh frequency settings for the system SEQUENCE OF TxHighFreqEntry .1.3.6.1.4.1.7262.1.14.3 |
txHighFreqEntryA txHighFrequency entry containing all the frequency values TxHighFreqEntry .1.3.6.1.4.1.7262.1.14.3.1 |
txHighFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.3.1.1 |
txHighFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.3.1.2 |
txHighFreqTransmitIfFrequencyThe IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.3.1.3 |
txHighFreqReceiveIfFrequencyThe IF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.3.1.4 |
txHighFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.3.1.5 |
txHighFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.3.1.6 |
txHighFreqAvailableSpecifies whether the frequency channel can be used.rw Enumeration .1.3.6.1.4.1.7262.1.14.3.1.7 |
txHighFreqSelectedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.1.14.3.1.8 |
txLowFreqTableA table of txLow frequency settings for the system SEQUENCE OF TxLowFreqEntry .1.3.6.1.4.1.7262.1.14.4 |
txLowFreqEntryA txLowFrequeny entry containing the frequency values
for a specific index TxLowFreqEntry .1.3.6.1.4.1.7262.1.14.4.1 |
txLowFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.4.1.1 |
txLowFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.4.1.2 |
txLowFreqTransmitIfFrequencyThe IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.4.1.3 |
txLowFreqReceiveIfFrequencyThe IF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.4.1.4 |
txLowFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.4.1.5 |
txLowFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.4.1.6 |
txLowFreqAvailableSpecifies whether the frequency channel can be used.rw Enumeration .1.3.6.1.4.1.7262.1.14.4.1.7 |
txLowFreqSelectedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.1.14.4.1.8 |
goFreqTableA table of go frequency settings for the system SEQUENCE OF GoFreqEntry .1.3.6.1.4.1.7262.1.14.5 |
goFreqEntryA goFrequency entry containing all the frequency values GoFreqEntry .1.3.6.1.4.1.7262.1.14.5.1 |
goFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.5.1.1 |
goFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.5.1.2 |
goFreqTransmitIfFrequencyThe IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.5.1.3 |
goFreqReceiveIfFrequencyThe IF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.5.1.4 |
goFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.5.1.5 |
goFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.5.1.6 |
goFreqAvailableSpecifies whether the frequency channel can be used.ro Enumeration .1.3.6.1.4.1.7262.1.14.5.1.7 |
goFreqSelectedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.1.14.5.1.8 |
returnFreqTableA table of return frequency settings for the system SEQUENCE OF ReturnFreqEntry .1.3.6.1.4.1.7262.1.14.6 |
returnFreqEntryA returnFrequency entry containing all the frequency values ReturnFreqEntry .1.3.6.1.4.1.7262.1.14.6.1 |
returnFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.6.1.1 |
returnFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.6.1.2 |
returnFreqTransmitIfFrequencyThe IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.6.1.3 |
returnFreqReceiveIfFrequencyThe IF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.6.1.4 |
returnFreqTransmitRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.6.1.5 |
returnFreqReceiveRfFrequencyThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.6.1.6 |
returnFreqAvailableSpecifies whether the frequency channel can be used.ro Enumeration .1.3.6.1.4.1.7262.1.14.6.1.7 |
returnFreqSelectedSpecifies the operating frequency channel for the modem.
***Only 1 index may be selected in a 1 modem system.rw Enumeration .1.3.6.1.4.1.7262.1.14.6.1.8 |
unlicensedTxFreqTableOBSOLETE. A table of unlicensed Tx frequency settings for the system SEQUENCE OF UnlicensedTxFreqEntry .1.3.6.1.4.1.7262.1.14.7 |
unlicensedTxFreqEntryA unlicensed Tx entry containing all the frequency values UnlicensedTxFreqEntry .1.3.6.1.4.1.7262.1.14.7.1 |
unlicensedTxFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.7.1.1 |
unlicensedTxFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.7.1.2 |
unlicensedTxIfFrequencyThe IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.7.1.3 |
unlicensedTxRfFrequencyThe RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.7.1.4 |
setUnlicensedTxFrequencyTo set the TX frequencies in the progrmmed frequency.rw Enumeration .1.3.6.1.4.1.7262.1.14.7.1.5 |
unlicensedRxFreqTableOBSOLETE. A table of unlicensed Rx frequency settings for the system SEQUENCE OF UnlicensedRxFreqEntry .1.3.6.1.4.1.7262.1.14.8 |
unlicensedRxFreqEntryA unlicensed Rx entry containing all the frequency values UnlicensedRxFreqEntry .1.3.6.1.4.1.7262.1.14.8.1 |
unlicensedRxFreqIndexA unique value for each frequency channel.ro INTEGER .1.3.6.1.4.1.7262.1.14.8.1.1 |
unlicensedRxFreqChannelIndexThe channel index for the frequency.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.8.1.2 |
unlicensedRxIfFrequencyThe IF Rx frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.8.1.3 |
unlicensedRxRfFrequencyThe RF Rx frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.8.1.4 |
setUnlicensedRxFrequencyTo set the Rx frequencies in the progrmmed frequency.rw Enumeration .1.3.6.1.4.1.7262.1.14.8.1.5 |
programmedFrequency OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.14.9 |
programmedFrequencyChannelThe channel that has been programmed into the system.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.14.9.1 |
programmedFrequencyTxIfThe programmed IF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.9.2 |
programmedFrequencyRxIfThe programmed IF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.9.3 |
programmedFrequencyTxRfThe programmed RF TX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.9.4 |
programmedFrequencyRxRfThe RF RX frequency in MHz.ro INTEGER .1.3.6.1.4.1.7262.1.14.9.5 |
apFrequencyFile OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.14.10 |
frequencyFileOptionOption which tells whether frequency file is being used for system settings.ro Enumeration .1.3.6.1.4.1.7262.1.14.10.1 |
apModem OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.15 |
mdmDescA textual string containing information about the modem.
Includes the manufacturer, product name, software
version, and hardware version of the modem card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.1 |
mdmModulationTypeThe modulation type of the modem, distinguished according
to the physical/link protocol.ro Enumeration .1.3.6.1.4.1.7262.1.15.2 |
mdmCurrentRxSpeedAn estimate of the modem's current Rx bandwidth in bits per
second.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.3 |
mdmCurrentTxSpeedAn estimate of the modem's current Tx bandwidth in bits per
second.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.4 |
mdmAdminStatusNOT IMPLEMENTED
The desired state of the modem card. 'testing' and 'down'
indicates that no user packet data can be passed.rw Enumeration .1.3.6.1.4.1.7262.1.15.5 |
mdmOperStatusThe current operational state of the interface. Testing
indicates that no operational packets can be passed.ro Enumeration .1.3.6.1.4.1.7262.1.15.6 |
mdmLastChangeThe value of sysUpTime at the time the modem entered its
current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains
a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.7262.1.15.7 |
mdmBerAn estimation of the current uncorrected BER. Uncorrected BER is the bit error rate as measured before frame error correction.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.8 |
mdmEbToNoiseRatioThe ratio of the modem Estimated Energy per information bit to Noise power spectral densityro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.9 |
mdmRSLNOT USED. DEPRECATED. Use radioRSL object in radio folder. The Received Signal Level at the demodulator. Indicates the power of the receive level in -dBm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.10 |
mdmEqualizerStressIndicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.11 |
mdmResetWriting 1 to this object causes the modem card to be reset.
All other values are not recognized. This variable always
reads back as 0. mdmOperStatus should be polled by the
user after this object is written to, to verify that the
modem card has been reset.rw INTEGER ( 0 .. 1 ) .1.3.6.1.4.1.7262.1.15.12 |
mdmSlopeEqualizerStressA floating point number indicating how much the received
signal has been spectrally sloped.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.13 |
mdmPhaseImbalanceReports the I/Q phase correction applied by demodulator
ASSP correction loops.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.14 |
mdmAmplitudeImbalanceReports the I/Q amplitude correction applied by demodulator
ASSP correction loops.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.15.15 |
mdmStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.15.16 |
mdmFramesOutThe current count of Modem frames sent.ro Counter .1.3.6.1.4.1.7262.1.15.16.1 |
mdmFramesBlocksInThe current count of Modem blocks received.ro Counter .1.3.6.1.4.1.7262.1.15.16.2 |
mdmFramesBlocksInErrorThe current count of Modem blocks received in error.ro Counter .1.3.6.1.4.1.7262.1.15.16.3 |
mdmFramesInThe current count of Modem frames received.ro Counter .1.3.6.1.4.1.7262.1.15.16.4 |
mdmFramesInErrorThe current count of Modem frames received in error.ro Counter .1.3.6.1.4.1.7262.1.15.16.5 |
mdmQueueFramesDiscardedThe current count of Modem frames in the queue that were discarded.ro Counter .1.3.6.1.4.1.7262.1.15.16.6 |
mdmBWUtilizationThe carried load over link capacity.ro INTEGER .1.3.6.1.4.1.7262.1.15.16.7 |
mdmIngressDataRateThe data rate coming into the ethernet port.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbsro INTEGER .1.3.6.1.4.1.7262.1.15.16.8 |
mdmEgressDataRateThe data rate going out of the ethernet port.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbs.ro INTEGER .1.3.6.1.4.1.7262.1.15.16.9 |
aamStatusIndicates whether Automatic Adaptive Modulation(AAM) is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.15.17 |
mdmCurrentRxSpeedIntInteger version of 'mdmCurrentRxSpeed' object. Divide by '10000' to get the
actual value. Mainly provided to facilitate plotting of values. An estimate of the modem's current Rx bandwidth in bits per
second.ro INTEGER .1.3.6.1.4.1.7262.1.15.18 |
mdmCurrentTxSpeedIntInteger version of 'mdmCurrentTxSpeed' object. Divide by '10000' to get the
actual value. Mainly provided to facilitate plotting of values. An estimate of the modem's current Tx bandwidth in bits per
second.ro INTEGER .1.3.6.1.4.1.7262.1.15.19 |
mdmBerIntInteger version of 'mdmBer' object.Divide by 1e+8 to get the actual value. Any value less than 1e-8 will
be truncated to 0.Mainly provided to facilitate plotting of values.
An estimation of the current uncorrected BER.
Uncorrected BER is the bit error rate as measured before frame error correction.ro INTEGER .1.3.6.1.4.1.7262.1.15.20 |
mdmEbToNoiseRatioIntInteger version of 'mdmEbToNoiseRatio' object. Divide by '10' to get the
actual value. Mainly provided to facilitate plotting of values. The ratio of the modem Estimated
Energy per information bit to Noise power spectral density.ro INTEGER .1.3.6.1.4.1.7262.1.15.21 |
mdmSlopeEqualizerStressIntInteger version of 'mdmSlopeEqualizerStress' object. Divide by '100' to get the
actual value. Mainly provided to facilitate plotting of values.A floating point number indicating how much the received
signal has been spectrally sloped.ro INTEGER .1.3.6.1.4.1.7262.1.15.22 |
mdmPhaseImbalanceIntInteger version of 'mdmPhaseImbalance' object. Divide by '100' to get the
actual value. Mainly provided to facilitate plotting of values.Reports the I/Q phase correction applied by demodulator
ASSP correction loops.ro INTEGER .1.3.6.1.4.1.7262.1.15.23 |
mdmAmplitudeImbalanceIntInteger version of 'mdmAmplitudeImbalance' object. Divide by '100' to get the
actual value. Mainly provided to facilitate plotting of values. Reports the I/Q amplitude correction applied by demodulator
ASSP correction loops.ro INTEGER .1.3.6.1.4.1.7262.1.15.24 |
apRadio OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.16 |
radioDescA textual string containing information about the radio.
Includes the manufacturer, product name, software version,
serial number, and hardware version of the radio.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.16.1 |
radioPhysAddrThe physical address used to distinguish it from other
radios.ro INTEGER .1.3.6.1.4.1.7262.1.16.2 |
radioAdminStatusOBSOLETE. The desired state of the radio. The radio only transmits
when in the up state i.e. the transmitter is muted when
in the down, testing state or firmware upgrade state.rw Enumeration .1.3.6.1.4.1.7262.1.16.3 |
radioOperStatusThe current operational state of the interface. Testing
indicates that no operational packets can be passed. Testing
also indicates that a firmware upgrade may be in progressro Enumeration .1.3.6.1.4.1.7262.1.16.4 |
radioLastChangedThe value of sysUpTime at the time the radio entered
its current operational state. If the current state was
entered prior to the last re-initialization of the local
network management subsystem, then this object contains
a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.7262.1.16.5 |
radioRSLThe Received Signal Level indicates the power of the receive level in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm.ro INTEGER .1.3.6.1.4.1.7262.1.16.6 |
radioTxGainThe gain of the radio in the transmit chain. Indicates
the gain in dB.rw INTEGER ( 20 .. 40 ) .1.3.6.1.4.1.7262.1.16.7 |
radioRxGainThe gain of the radio in the receive chain. Indicates
the gain in dB.rw INTEGER ( 20 .. 40 ) .1.3.6.1.4.1.7262.1.16.8 |
radioVoltageSupplyThe voltage level of the supply to the radio.ro INTEGER .1.3.6.1.4.1.7262.1.16.9 |
radioResetWriting 1 to this object causes the radio to be reset.
All other values are not recognized. This variable
always reads back as 0. radioOperStatus should be polled
by the user after this object is written to, to verify
that the radio card has been reset.rw INTEGER ( 0 .. 1 ) .1.3.6.1.4.1.7262.1.16.10 |
transmitPowerDbmThis defines the transmit level of the radio.
If ATPC is enabled, you can't change the transmit power.
The power you see is divided by 10. e.g. A display
of 133 is actually 13.3 dBm.
If the radio is operational and not muted, it is the
current transmitting power.
If the radio is operational and muted, it is the
programmed transmitting power, and will transmit at
this level when the radio is un-muted.
If the radio is not operational it is the programmed
transmitting power, and will transmit at this level
when the radio is operational and not muted.
If the radio does not have transmit calibration tables
programmed into its EEPROM, this transmit power level
cannot be used as it is not possible to accurately
calculate the actual transmit level. In this case this
object will return -99.rw INTEGER .1.3.6.1.4.1.7262.1.16.11 |
programmedAntennaDiameterThis defines the diameter of the antenna used by the system represented in inches.rw Enumeration .1.3.6.1.4.1.7262.1.16.12 |
powerOptionThis indicates the power option of the radio: normal or high power.rw Enumeration .1.3.6.1.4.1.7262.1.16.13 |
atpcStatusIndicates whether Automatic Transmit Power Control (ATPC) is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.16.14 |
atpcRslThresholdThis defines the atpc rsl threshold.ro INTEGER ( -800 .. -300 ) .1.3.6.1.4.1.7262.1.16.15 |
atpcFadeStepThis defines atpc fade step size.ro INTEGER ( 1 .. 50 ) .1.3.6.1.4.1.7262.1.16.16 |
atpcRslHysteresisThis defines the rsl hysteresis.ro INTEGER ( 1 .. 15 ) .1.3.6.1.4.1.7262.1.16.17 |
atpcMaximumChangeThis defines the maximum allowed atpc change.ro INTEGER ( 1 .. 50 ) .1.3.6.1.4.1.7262.1.16.18 |
redundancyStatusIndicates whether radio redundancy is enabled or not.
It can be turned on only when there is valid primary and
secondary serial number in flashrw Enumeration .1.3.6.1.4.1.7262.1.16.19 |
redundancyModeRadio installtion type
dcdp - different channel or differenr polarzation,
scsp - same channel and same polarizationrw Enumeration .1.3.6.1.4.1.7262.1.16.20 |
redundancyCurrentSerialNumDisplay active radio's serial numberro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.16.21 |
redundancySecondarySerialNumDisplay the secondary radio's serial number in flashrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.16.22 |
redundancyPrimarySerialNumDisplay the primary radio's serial number in flashrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.16.23 |
radioRSLUnsignedIntThe Received Signal Level indicates the power of the receive level in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm.
Object provided mainly to accomodate plotting of negative RSL values which is not supported in some EMS (Ex: CastleRock).
Please use 'radioRSL' object if your EMS supports plotting of -ve integer.ro INTEGER .1.3.6.1.4.1.7262.1.16.24 |
radioTemperatureThe Radio temperature in degree Centigrade. The actual temperature is got by dividing the number by 10. e.g. -432 is actually -43.2 degree centigrade.ro INTEGER .1.3.6.1.4.1.7262.1.16.25 |
apCalendar OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.17 |
dateA string in the format as follows:
XX/YY/ZZ
Where XX = day of month (range 01 to 31)
YY = month of year(range 01 to 12)
ZZ = year (range 01 - 99)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.17.1 |
timeA string in the format as follows:
aa:bb:cc:dd
Where aa = hour of day ( range 00 to 23 )
bb = minute of hour ( range 00 to 59 )
cc = second of minute( range 00 to 59 )
dd = hundredths of second (range 00 to 99)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.17.2 |
apLeds OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.18 |
powerLedIndicates the status of the power led.ro Enumeration .1.3.6.1.4.1.7262.1.18.1 |
linkStatusOrSpeedLedIndicates the status of Ethernet link for release 3 or earlier hardware platforms.
Indicates the speed of the Ethernet link for release 4 or later platforms.
The values fastBlink1000BaseT, solidOn100BaseT, and slowBlink10BaseT are applicable only to release 4 hardware platforms.ro Enumeration .1.3.6.1.4.1.7262.1.18.2 |
trafficLedIndicates the presence of Ethernet traffic. It represents transmit and receive traffic on the ethernet interface.ro Enumeration .1.3.6.1.4.1.7262.1.18.3 |
duplexModeOrLinkTypeLedFor release 3 or earlier hardward platforms,
indicates whether the Ethernet link is working in full duplex mode, 1 means
off and 2 means on. The values of 3, 4, and 5 do not apply.
For release 4 hardware platforms or later, off (1) and on (2) does not apply.
In this case, 3 means copper interface led is off, 4 means optical interface
optical transmitter Off led is slowly blinking, and 5 means optical
interface led is on.ro Enumeration .1.3.6.1.4.1.7262.1.18.4 |
rfOnLedIndicates whether the radio is transmitting or notro Enumeration .1.3.6.1.4.1.7262.1.18.5 |
modemSyncLedIndicates that the modem is synchronized to another AirPairro Enumeration .1.3.6.1.4.1.7262.1.18.6 |
systemTroubleLedIndicates the status of the system trouble LED.
The Trouble LED will be on if on of the following
conditions exist:
i)Communication with the radio has failed.
ii) The PLDRO has lost lock on the Radio
iii) The synthesizers are not locked on the IF Card.
The alarm group should be checkedro Enumeration .1.3.6.1.4.1.7262.1.18.7 |
multiSegmentLedNOT IMPLEMENTED
Indicates the value loaded to the multi-segment LED.
Used for antenna alignment. Value is read as a
percentage.ro Enumeration .1.3.6.1.4.1.7262.1.18.8 |
fanAlarmLedIndicates whether the fan alarm led is off or not.If any one of the fan stops working, this led will be turned on.
This alarm is applicable for split IDU/ODU modems only.ro Enumeration .1.3.6.1.4.1.7262.1.18.9 |
apSystemAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19 |
clearAlarmCountersClears the alarm counters for the specified grouprw Enumeration .1.3.6.1.4.1.7262.1.19.1 |
networkInterfaceCardAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.2 |
explicitAuthenticationFailureAuthentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.1 |
explicitAuthenticationFailureCountIndicates the number of times explicit authentication has failed.ro Counter .1.3.6.1.4.1.7262.1.19.2.2 |
autoNegotiationDuplexMismatchNOT USED. DEPRECATED. The AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to AirPair, or the AirPair autonegotion settings. The recommended course of action is to check the connection.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.3 |
autoNegotiationDuplexMismatchCountNOT USED. DEPRECATED. Indicates the number of times auto negotiation has failed.ro Counter .1.3.6.1.4.1.7262.1.19.2.4 |
droppedEnetFramesThresholdExceededThe threshold for number of frames dropped has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.5 |
droppedEnetFramesThresholdParametersA read-write string: The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of frames that are dropped, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.19.2.6 |
droppedEnetFramesThresholdCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.1.19.2.7 |
bandwidthUtilizationThresholdExceededThe threshold for the percentage of available bandwidth has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.8 |
bandwidthUtilizationThresholdParametersA read-write string: The percentage of available bandwidth threshold and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the threshold point in percent, the number of seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.19.2.9 |
bandwidthUtilizationThresholdCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.1.19.2.10 |
rlsMismatchRLS configurations on the pair of systems are mismatched.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.11 |
rlsMismatchCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.1.19.2.12 |
rLSShutdownActivatedRLS shutdown is activated.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.13 |
rLSShutdownActivatedCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.1.19.2.14 |
ethernetLinkDownIndicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to AirPair. The recommended course of action is to check the connection.ro Enumeration .1.3.6.1.4.1.7262.1.19.2.15 |
ethernetLinkDownActivatedCountIndicates the approximate time, in seconds, that this alarm has been in the active statero Counter .1.3.6.1.4.1.7262.1.19.2.16 |
modemAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.3 |
modemLossOfSignalLockFromDemodulatorLoss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.1 |
modemLossOfSignalLockFromDemodulatorCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.2 |
modemUncorrectedBerThresholdExceededThe uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.3 |
modemUncorrectedBerThresholdParametersA read-write string: The threshold, in exponential format, and the number of seconds in exponential format that the uncorrected BER must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '1.2e-4 1.1e-1'. The first parameter is uncorrected BER threshold point, the second is the time in seconds that the threshold must be exceeded. In this example the threshold is set to 1.2 bits every 1000 and the time is set to 0.11 of a second. The single quote marks i.e. ' ' are not used in the command. Uncorrected BER is the bit error rate as measured before frame error correction.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.19.3.4 |
modemUncorrectedBerThresholdExceededCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.5 |
modemModulatorPllLockFailureModulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the modem unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.6 |
modemModulatorPllLockFailureCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.7 |
modemModulatorLossOfSyncBytesLoss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the air pair nodes.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.8 |
modemModulatorLossOfSyncBytesCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.9 |
modemModulatorInputFifoErrorOverrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or relpace the modem unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.10 |
modemModulatorInputFifoErrorCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.11 |
modemModulatorInputDataErrorAll ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or replace the modem unitro Enumeration .1.3.6.1.4.1.7262.1.19.3.12 |
modemModulatorInputDataErrorCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.13 |
modemSnrBelowThresholdThe demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.14 |
modemSnrAlarmThresholdParameterThe demodulator SNR threshold level which triggers the modemSnrBelowThreshold alarm. A number in the range 10 to 25. The proper setting depends on the operational parameters of the system e.g. QPSK, QAM16, QAM32 and the expected link budget.rw INTEGER .1.3.6.1.4.1.7262.1.19.3.15 |
modemSnrBelowThresholdCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.16 |
modemCardMismatchedHardwareFirmwareThe modem card has firmware that is incompatible with the hardware. The card will not operate properly.ro Enumeration .1.3.6.1.4.1.7262.1.19.3.17 |
modemCardMismatchedHardwareFirmwareCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.18 |
modemAAMConfigMismatchIn the near end Automatic Adaptive Modulation(AAM) feature set to on and in peer it is set to offro Enumeration .1.3.6.1.4.1.7262.1.19.3.19 |
modemAAMConfigMismatchCountIndicates the approximate number of seconds AAMConfigMismatch alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.20 |
modemAAMQpskActiveIndicates aam is active and system running on QPSK modulationro Enumeration .1.3.6.1.4.1.7262.1.19.3.21 |
modemAAMQpskActiveCountIndicates the approximate number of seconds AAMQpskActive alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.3.22 |
radioAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.4 |
radioPLDROLostLockThe PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.1 |
radioPLDROLostLockCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.2 |
radioLostCommunicationRS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recommended course of action is to check the connection.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.3 |
radioLostCommunicationCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.4 |
radioMismatchThe radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrectly programmed modem or an incorrect radio type connected to the modem, and recommended course of action is to check the modem frequency settings and radio hardware version number or serial number.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.5 |
radioMismatchCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.6 |
radioPowerAmpThe power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.7 |
radioPowerAmpCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.8 |
radioRslBelowThresholdThe minimum radio receive signal level threshold has been crossed. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.9 |
radioRslBelowThresholdParametersA read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the second is the time in seconds that the threshold must be exceeded. In this example the threshold -75 dBm and the time is set to 10 seconds. The single quote marks i.e. ' ' are not used in the command.rw DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.19.4.10 |
radioRslBelowThresholdCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.11 |
radioHighPowerOptionM1This applies to High Power Radios only. Indicates Power Amp Alarm (M1).ro Enumeration .1.3.6.1.4.1.7262.1.19.4.12 |
radioHighPowerOptionM1CountThis applies to High Power Radios only. Indicates the number of seconds that Power Amp Alarm (M1) has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.13 |
radioHighPowerOptionM2This applies to High Power Radios only. Indicates Power Amp Alarm (M2).ro Enumeration .1.3.6.1.4.1.7262.1.19.4.14 |
radioHighPowerOptionM2CountThis applies to High Power Radios only. Indicates the number of seconds that Power Amp Alarm (M2) has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.15 |
radioHighPowerTxDetectorThis applies to High Power Radios only. Indicates minimum power threshold has not been surpassed.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.16 |
radioHighPowerTxDetectorCountThis applies to High Power Radios only. Indicates the number of seconds that radioHighPowerTxDetector alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.4.17 |
atpcConfigMismatchThe pair of the systems don't have same ATPC configurations. On
one side ATPC is enabled, but on the other side ATPC is not
enabled.ro Enumeration .1.3.6.1.4.1.7262.1.19.4.18 |
atpcConfigMismatchCountIndicates how long atpc configurations are mismatched on the
two systems.ro Counter .1.3.6.1.4.1.7262.1.19.4.19 |
redundancySecondaryActiveRadio redundancy on, secondary radio is activero Enumeration .1.3.6.1.4.1.7262.1.19.4.20 |
redundancySecondaryActiveCountIndicates how long secondary radio is active.ro Counter .1.3.6.1.4.1.7262.1.19.4.21 |
redundancySerialNumMismatchRadio serial number programmed in flash and radio doesn't matchro Enumeration .1.3.6.1.4.1.7262.1.19.4.22 |
redundancySerialNumMismatchCountIndicates how long redundancyserailNumMismatch alarm is active.ro Counter .1.3.6.1.4.1.7262.1.19.4.23 |
excessiveCableLossChangeCable loss change exceeds the thresholdro Enumeration .1.3.6.1.4.1.7262.1.19.4.24 |
excessiveCableLossChangeCountIndicates how long Cable loss change has exceeded the thresholdro Counter .1.3.6.1.4.1.7262.1.19.4.25 |
excessiveRxCableLossRx gain can not be adjusted to desired valuero Enumeration .1.3.6.1.4.1.7262.1.19.4.26 |
excessiveRxCableLossCountIndicates how long rx gain can not be adjusted to desired valuero Counter .1.3.6.1.4.1.7262.1.19.4.27 |
intermediateFrequencyCardAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.5 |
ifTxSynthesizerUnlockedThe IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.5.1 |
ifTxSynthesizerUnlockedCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.5.2 |
ifRxSynthesizerUnlockedThe IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit.ro Enumeration .1.3.6.1.4.1.7262.1.19.5.3 |
ifRxSynthesizerUnlockedCountIndicates the approximate number of seconds that this alarm has been active.ro Counter .1.3.6.1.4.1.7262.1.19.5.4 |
otherAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.6 |
rxCableLossExcessiveThe Rx cable loss exceeds limit.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.19.6.1 |
rxCableLossExcessiveCountIndicates the approximate number of seconds that this alarm has been active.
Valid only when the installation type is IDU-ODU splitro Counter .1.3.6.1.4.1.7262.1.19.6.2 |
txCableLossExcessiveThe Tx cable loss exceeds limit.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.19.6.3 |
txCableLossExcessiveCountIndicates the approximate number of seconds that this alarm has been active.
Valid only when the installation type is IDU-ODU splitro Counter .1.3.6.1.4.1.7262.1.19.6.4 |
fan1FailedThe fan 1 failed.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.19.6.5 |
fan1FailedCountIndicates the approximate number of seconds that this alarm has been active.
Valid only when the installation type is IDU-ODU splitro Counter .1.3.6.1.4.1.7262.1.19.6.6 |
fan2FailedThe fan 2 failed.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.19.6.7 |
fan2FailedCountIndicates the approximate number of seconds that this alarm has been active.
Valid only when the installation type is IDU-ODU splitro Counter .1.3.6.1.4.1.7262.1.19.6.8 |
reservedTo be filled.ro Enumeration .1.3.6.1.4.1.7262.1.19.6.9 |
reservedAlarmCountTo be filled.ro Counter .1.3.6.1.4.1.7262.1.19.6.10 |
sntpServerUnavailableAlarmAll of the SNTP servers are not available.ro Enumeration .1.3.6.1.4.1.7262.1.19.6.11 |
sntpServerUnavailableAlarmCountIndicates how long in seconds all of the SNTP servers are not available.ro Counter .1.3.6.1.4.1.7262.1.19.6.12 |
frequencyFileAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.19.7 |
frequencyFileInvalidExecuting frequency file is valid or notro Enumeration .1.3.6.1.4.1.7262.1.19.7.1 |
frequencyFileInvalidCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.1.19.7.2 |
optionalParaNotEnteredExecuting frequency file doesn't contain all the parameters needed for optimum performance of the system.ro Enumeration .1.3.6.1.4.1.7262.1.19.7.3 |
optionalParaNotEnteredCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.1.19.7.4 |
progRadioBandNotFoundExecuting frequency file doesn't contain radio band info that is programmed in the system.ro Enumeration .1.3.6.1.4.1.7262.1.19.7.5 |
progRadioBandNotFoundCountIndicates the time (in secs) since this alarm exist.ro Counter .1.3.6.1.4.1.7262.1.19.7.6 |
apSnmpTraps OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.20 |
explicitAuthenticationFailureV1TrapAuthentication of the peer AirPair node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on AirPair faulty cable between the modem and radio, and recommended course of action is to check both ends of the link. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.3 |
autoNegotiationDuplexMismatchV1TrapThe AirPair ethernet interface has a mismatch in duplex. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to AirPair, or the AirPair autonegotion settings. The recommended course of action is to check the connection. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.4 |
modemLossOfSignalLockFromDemodulatorV1TrapLoss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.5 |
modemUncorrectedBerThresholdExceededV1TrapThe uncorrected BER threshold has been exceeded. The severity is major, the probable cause is physical interference in the air link or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.6 |
modemModulatorPllLockFailureV1TrapModulator PLL failure. The severity is critical, the probable cause a faulty modem card within AirPair, and recommended course of action is to replace the modem unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.7 |
modemModulatorLossOfSyncBytesV1TrapLoss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the air pair nodes. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.8 |
modemModulatorInputFifoErrorV1TrapOverrun or underrun of the FIFO contained inside the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or relpace the modem unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.9 |
modemModulatorInputDataErrorV1TrapAll ones or all zeroes at the input of the modulator. The severity is critical, the probable cause is electrical interference, and recommended course of action is to reset the modem unit, or replace the modem unit TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.10 |
modemSnrBelowThresholdV1TrapThe demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the air pair nodes. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.11 |
radioPLDROLostLockV1TrapThe PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.12 |
radioLostCommunicationV1TrapRS232 communication lost between AIRPAIR and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recommended course of action is to check the connection. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.13 |
radioMismatchV1TrapThe radio connected to the AIRPAIR modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrectly programmed modem or an incorrect radio type connected to the modem, and recommended course of action is to check the modem frequency settings and radio hardware version number or serial number. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.14 |
radioPowerAmpV1TrapThe power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit within AirPair, and recommended course of action is to replace the radio unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.15 |
ifTxSynthUnlockedV1TrapThe IF card within the modem unit has a Transmit Synthesizer which is not locked and as a result will not transmit. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.16 |
ifRxSynthUnlockedV1TrapThe IF card within the modem unit has a Receive Synthesizer which is not locked. The severity is critical, the probable cause an incorrectly programmed frequency setting in the modem or a faulty IF card, and recommended course of action is to check frequency setting in the modem or to replace the modem unit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.17 |
ttySessionCommencedV1TrapA person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.18 |
ttySessionTerminatedV1TrapA person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.19 |
rslBelowThresholdV1TrapThe RSL has been detected below its minimum threshold. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.20 |
droppedFramesThresholdExceededV1TrapThe ethernet dropped frames threshold has been detected above its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.21 |
bwUtilizationThresholdExceededV1TrapThe ethernet bandwidth threshold has been detected above its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.22 |
explicitAuthFailureClearedV1TrapThe condition has cleared. The peer node is now authenticated. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.23 |
autoNegDuplexMismatchClearedV1TrapThe condition has cleared. The Ethernet connection is not experiencing auto-negotiation duplex mismatch. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.24 |
lossOfSyncSigFromDemoClearedV1TrapThe condition has cleared. The demodulator is synchronized. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.25 |
uncorrectedBerThresExceededClearedV1TrapThe condition has cleared. The demodulator uncorrected BER is now below its minimum threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.26 |
modemModPLLFailureClearedV1TrapThe condition has cleared. The modem PLL is not failing. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.27 |
modemModLossOfSyncBytesClearedV1TrapThe condition has cleared. The modem is not experiencing loss of synch bytes. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.28 |
modemModInputFifoOverUnderClearedV1TrapThe condition has cleared. The modem is not experiencing input FIFO over/under runs. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.29 |
modemModInputDataInacClearedV1TrapThe condition has cleared. The modem is not experiencing data inactivity. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.30 |
snrBelowThresholdClearedV1TrapThe condition has cleared. SNR is now above its minimum threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.31 |
radioPLDROLostLockClearedV1TrapThe condition has cleared. The radio PLDRO/LO lost lock condition has cleared. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.32 |
radioLostCommunicationClearedV1TrapThe condition has cleared. RS232 communication has been re-establisted between AIRPAIR and the radio. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.33 |
radioMismatchClearedV1TrapThe condtion has cleared. The radio matches the programmed parameters in the modem. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.34 |
radioPowerAmpClearedV1TrapThe condtion has cleared. The radio Power Amp is not in the failed state. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.35 |
ifTxSynthUnlockedClearedV1TrapThe condtion has cleared. The IF stage transmit synthesizer is now locked. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.36 |
ifRxSynthUnlockedClearedV1TrapThe condtion has cleared. The IF stage receive synthesizer is now locked. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.37 |
rslBelowThresholdClearedV1TrapThe condition has cleared. RSL is now above its minimum threshold. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.38 |
droppedFramesThresholdExceededClearedV1TrapThe condition has cleared.The ethernet dropped frames threshold is now below its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.39 |
bwUtilizationThresholdExceededClearedV1TrapThe condition has cleared. The ethernet bandwidth threshold is now below its threshold value. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.40 |
rxIfCableLossExceededV1TrapThe Rx cable loss has exceeded limit.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.41 |
rxIfCableLossExceededClearedV1TrapThe condition has cleared. The Rx cable loss is now within limit.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.42 |
txIfCableLossExceededV1TrapThe Tx cable loss has exceeded limit.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.43 |
txIfCableLossExceededClearedV1TrapThe condition has cleared. The Tx cable loss is now within limit.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.44 |
fan1FailedV1TrapThe Fan1 has failed.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.45 |
fan1FailedClearedV1TrapThe condition has cleared. The fan1 is running normally.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.46 |
fan2FailedV1TrapThe Fan2 has failed.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.47 |
fan2FailedClearedV1TrapThe condition has cleared. The fan2 is running normally.
This trap is only valid when the AirPair installation type is IDU-ODU split TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.48 |
modemCardMismatchedHardwareFirmwareV1TrapThe modem card has firmware that is incompatible with the hardware. The card will not operate properly. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.49 |
modemCardMismatchedHardwareFirmwareClearedV1TrapThe condition has cleared. The modem card does not have incompatible firmware with the hardware. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.50 |
atpcConfigMismatchV1TrapATPC configuration mismatch in the Airpair systems. ATPC is
enabled at one system, but ATPC is not enabled at the other
system. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.51 |
atpcConfigMismatchClearedV1TrapATPC configuration mismatch in the Airpair systems is cleared.
Both systems enabled ATPC. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.52 |
radioHiPwrOptM1V1TrapWhen hi-power radio is used, hi-power gate M1 drain current
is out of lower or upper limits. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.53 |
radioHiPwrOptM1ClearedV1TrapWhen hi-power radio is used, hi-power gate M1 drain current
is between lower and upper limits. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.54 |
radioHiPwrOptM2V1TrapWhen hi-power radio is used, hi-power gate M2 drain current
is out of lower or upper limits. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.55 |
radioHiPwrOptM2ClearedV1TrapWhen hi-power radio is used, hi-power gate M2 drain current
is between lower and upper limits. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.56 |
radioHiPwrTxDetectorV1TrapWhen hi-power radio is used, hi-power tx detector dBm value
is smaller than limit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.57 |
radioHiPwrTxDetectorClearedV1TrapWhen hi-power radio is used, hi-power tx detector dBm
value is not smaller than limit. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.58 |
sntpServersUnreachableV1TrapCan't reach any of the sntp servers TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.59 |
sntpServersUnreachableClearedV1TrapAt least one of SNTP servers is reachable TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.60 |
rlsMismatchV1TrapRLS mismatch TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.61 |
rlsMismatchClearedV1TrapRLS mismatch cleared TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.62 |
rLSShutdownActivatedv1TrapRLS shutdown is activated TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.63 |
rLSShutdownActivatedClearedV1TrapRLS shutdown is not activated TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.64 |
frequencyFileInvalidV1TrapWhen the executing frequency file is invalid,
this trap is generated. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.65 |
optionalParaNotEntFreqFileV1Trapwhen the optional parameters are not entered in frequency file,
and the system boots up, this trap is generated. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.66 |
progRadioBandNotFoundFreqFileV1Trapwhen the executing frequency file doesn't contain the info related to programmed
radio band, this trap is generated. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.67 |
redundancySwitchOverSuccessTrapRedundancy radio switch over success TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.68 |
redundancySwitchOverFailedTrapRedundancy radio switch over failed TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.69 |
radioNoAtpcSupportTrapRadio does not support atpc TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.70 |
radioNoAtpcSupportClearedTrapRadio does not support atpc cleared TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.71 |
radioFirmwareMismatchTrapRadio firmware on radio and on modem card mismatch TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.72 |
radioFirmwareMismatchClearedTrapRadio firmware mismatch cleared TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.73 |
redundancySwitchInitByLocalendRadio switch initiated by local end TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.74 |
redundancySwitchInitByPeerRadio switch initiated by peer TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.75 |
aamConfigMisMatchAdaptive modulation configuration mismatch TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.76 |
aamConfigMisMatchClearAdaptive modulation configuration mismatch cleared TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.77 |
aamQpskActiveAdaptive modulation on and system running on QPSK modulation TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.78 |
aamQpskActiveClearedAdaptive modulation on system running on higher modulation TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.79 |
primaryRadioFaultyTrapPrimary radio is faulty TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.80 |
primaryRadioFaultyClearedTrapprimary radio is not faulty anymore TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.81 |
radioSerialNumberMismatchTrapRedundancy, Radio Serial number mismatch. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.82 |
radioSerialNumberMismatchTrapClearedTrapRedundancy, Radio Serial number mismatch cleared. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.83 |
excessiveCableLossChangeTrapExcessive transmit cable loss change. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.84 |
excessiveCableLossChangeClearedTrapExcessive transmit cable loss change cleared. TRAP-TYPE .1.3.6.1.4.1.7262.1.20.0.85 |
snmpTrapHostTableTable containing SNMP trap host entries. SEQUENCE OF SnmpTrapHostEntry .1.3.6.1.4.1.7262.1.20.1 |
snmpTrapHostEntryThe snmp trap host entry containing all the trap host information SnmpTrapHostEntry .1.3.6.1.4.1.7262.1.20.1.1 |
snmpTrapHostIndexA unique value for each trap host.ro INTEGER .1.3.6.1.4.1.7262.1.20.1.1.1 |
snmpTrapHostModeIndicates how the snmp trap host is obtained for the system.ro Enumeration .1.3.6.1.4.1.7262.1.20.1.1.2 |
snmpTrapHostIpAddressIndicates snmp trap host IP address.ro IpAddress .1.3.6.1.4.1.7262.1.20.1.1.3 |
snmpTrapHostDomainNameNOT IMPLEMENTED. Indicates snmp trap host name that is used when DNS is used.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.20.1.1.4 |
snmpTrapHostCommunityNameThe community string name used in Traps.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.20.1.1.5 |
snmpTrapHostActivatedSpecifies whether traps are to be sent to this specific host or notro Enumeration .1.3.6.1.4.1.7262.1.20.1.1.6 |
coldStartTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.2 |
linkDownTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.3 |
linkUpTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.4 |
explicitAuthenticationFailureTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.5 |
autoNegotiationDuplexMismatchTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.6 |
modemLossOfSignalLockFromDemodulatorTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.7 |
modemUncorrectedBerThresholdExceededTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.8 |
modemModulatorPllLockFailureTrapDescriptionrw Enumeration .1.3.6.1.4.1.7262.1.20.9 |
modemModulatorLossOfSyncBytesTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.10 |
modemModulatorInputFifoErrorTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.11 |
modemModulatorInputDataErrorTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.12 |
modemSnrBelowThresholdTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.13 |
radioPLDROLostLockTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.14 |
radioLostCommunicationTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.15 |
radioMismatchTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.16 |
radioPowerAmpTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.17 |
ifTxSynthesizerUnlockedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.18 |
ifRxSynthesizerUnlockedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.19 |
ttyManagementSessionCommencedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.20 |
ttyManagementSessionTerminatedTrapSpecifies whether this trap is to be sent or notrw Enumeration .1.3.6.1.4.1.7262.1.20.21 |
rslThresholdExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the radio receive signal level threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.1.20.22 |
droppedFramesThresholdExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the dropped ethernet frames threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.1.20.23 |
bandwidthUtilizationThresholdExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.rw Enumeration .1.3.6.1.4.1.7262.1.20.24 |
ifRxCableLossExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
Valid only when the installation type is IDU-ODU splitrw Enumeration .1.3.6.1.4.1.7262.1.20.25 |
ifTxCableLossExceedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
Valid only when the installation type is IDU-ODU splitrw Enumeration .1.3.6.1.4.1.7262.1.20.26 |
fan1FailedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
Valid only when the installation type is IDU-ODU splitrw Enumeration .1.3.6.1.4.1.7262.1.20.27 |
fan2FailedTrapEnables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
Valid only when the installation type is IDU-ODU splitrw Enumeration .1.3.6.1.4.1.7262.1.20.28 |
mdmCardHardwareFirmwareMismatchTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.29 |
atpcConfigMismatchTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.30 |
hiPowerOptionM1TrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.31 |
hiPowerOptionM2TrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.32 |
hiPowerTxDetectorTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.33 |
sntpServersUnreachableTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.34 |
rlsMismatchTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.35 |
rLSShutdownActivatedTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.36 |
frequencyFileInvalidTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.37 |
optionalParaNotEntTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.38 |
progRadioBandNotFoundTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.39 |
radioRedundancySwitchOverSuccessTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.40 |
radioRedundancySwitchOverFailedTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.41 |
radioRedundancyNoAtpcSupportTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.42 |
radioRedundancyInvalidRadioFirmwareTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.43 |
radioRedundancySwitchByLocalEndTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.44 |
radioRedundancySwitchByPeerTrapEnables or disables the trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.45 |
aamConfigMismatchTrapEnables or disables the aamConfigMismatch trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.46 |
aamQpskActiveTrapEnables or disables the aamQpskActive trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.47 |
snmpV3TrapHostsTableTable containing snmp V3 trap host entries SEQUENCE OF SnmpV3TrapHostsEntry .1.3.6.1.4.1.7262.1.20.50 |
snmpV3TrapHostsEntryContains the snmp v3 trap host information SnmpV3TrapHostsEntry .1.3.6.1.4.1.7262.1.20.50.1 |
snmpV3TrapHostsIndexA unique value for each v3 trap host.ro INTEGER .1.3.6.1.4.1.7262.1.20.50.1.1 |
snmpV3TrapHostIpAddressIndicates snmp trap host IP address.ro IpAddress .1.3.6.1.4.1.7262.1.20.50.1.2 |
snmpV3TrapHostUserNameThe user name of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.20.50.1.3 |
snmpV3TrapHostAuthProtocolThe authentication alogorithm used by the v3 trap host.ro Enumeration .1.3.6.1.4.1.7262.1.20.50.1.4 |
snmpV3TrapHostAuthPasswordThe authentication password of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.20.50.1.5 |
snmpV3TrapHostPrivProtocolThe privacy encryiption alogorithm used by the v3 trap host.ro Enumeration .1.3.6.1.4.1.7262.1.20.50.1.6 |
snmpV3TrapHostPrivPasswordThe privacy password of the v3 trap host.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.20.50.1.7 |
snmpV3TrapHostActivatedSpecifies whether a specific v3 trap host is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.1.20.50.1.8 |
excessiveCblLossChangeTrapEnables or disables the excessiveCblLossChange trap.rw Enumeration .1.3.6.1.4.1.7262.1.20.51 |
apSnmpManagers OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.21 |
snmpUserAccessSpecifies the user access to the system.If access is set to managers then only managers with there ip addresses set in snmpManagersTable will be able to gain snmp access to the system. If access is set to any then any manager will be able to gain snmp access to the systemro Enumeration .1.3.6.1.4.1.7262.1.21.1 |
snmpManagerAnyCommunityNameThe community string name used by the 'any' manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.21.2 |
snmpManagersTableTable containing snmp manager entries SEQUENCE OF SnmpManagersEntry .1.3.6.1.4.1.7262.1.21.3 |
snmpManagersEntryContains the snmp manager information SnmpManagersEntry .1.3.6.1.4.1.7262.1.21.3.1 |
snmpManagersIndexA unique value for each manager.ro INTEGER .1.3.6.1.4.1.7262.1.21.3.1.1 |
snmpManagerIpAddressThe IP address of the Manager.ro IpAddress .1.3.6.1.4.1.7262.1.21.3.1.2 |
snmpManagerCommunityNameThe community string name used by the manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.21.3.1.3 |
snmpManagerActivatedSpecifies whether a specific manager is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.1.21.3.1.4 |
snmpV3ManagersTableTable containing snmp V3 manager entries SEQUENCE OF SnmpV3ManagersEntry .1.3.6.1.4.1.7262.1.21.4 |
snmpV3ManagersEntryContains the snmp v3 manager information SnmpV3ManagersEntry .1.3.6.1.4.1.7262.1.21.4.1 |
snmpV3ManagersIndexA unique value for each v3 manager.ro INTEGER .1.3.6.1.4.1.7262.1.21.4.1.1 |
snmpV3ManagerUserNameThe user name of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.21.4.1.2 |
snmpV3ManagerAuthProtocolThe authentication alogorithm used by the v3 manager.ro Enumeration .1.3.6.1.4.1.7262.1.21.4.1.3 |
snmpV3ManagerAuthPasswordThe authentication password of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.21.4.1.4 |
snmpV3ManagerPrivProtocolThe privacy encryiption alogorithm used by the v3 manager.ro Enumeration .1.3.6.1.4.1.7262.1.21.4.1.5 |
snmpV3ManagerPrivPasswordThe privacy password of the v3 Manager.ro DisplayString ( SIZE ( 0 .. 24 ) ) .1.3.6.1.4.1.7262.1.21.4.1.6 |
snmpV3ManagerActivatedSpecifies whether a specific v3 manager is allowed to access the systemro Enumeration .1.3.6.1.4.1.7262.1.21.4.1.7 |
apLinkAnalysis OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.22 |
unitsOBSOLETE. The units of measurement used in the link analysis.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.1 |
distanceInputMethodOBSOLETE. The input method used that determines whether distance between nodes coordinates were used for system calculations.ro Enumeration .1.3.6.1.4.1.7262.1.22.2 |
distanceBetweenNodesOBSOLETE. The distance between nodes, in either meters, or feet, depending on the the Units used. This object will be 0 if Longitude and Latitude are used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.3 |
latitudeThisNodeOBSOLETE.The latitude of this node.This object will be 0 if DistanceBetweenNodes is used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.4 |
longitudeThisNodeOBSOLETE. The longitude of this node.This object will be 0 if DistanceBetweenNodes is used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.5 |
latitudePeerNodeOBSOLETE. The latitude of the peer node.This object will be 0 if DistanceBetweenNodes is used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.6 |
longitudePeerNodeOBSOLETE. The longitude of the peer node.This object will be 0 if DistanceBetweenNodes is used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.7 |
linkAnalysisFrequencyBandOBSOLETE. The frequency band that this system was set up forro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.8 |
availabilityPercentageOBSOLETE. The required availability of the link. A value of 95999 is 95.000%ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.9 |
polarizationOBSOLETE. The polarization of the node.ro Enumeration .1.3.6.1.4.1.7262.1.22.10 |
linkAnalysisAirPairTypeOBSOLETE. The AirPair type that this system was set up asro Enumeration .1.3.6.1.4.1.7262.1.22.11 |
rainRegionOBSOLETE. The rain region of the site.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.12 |
antennaDiameterOBSOLETE. The diameter of the antenna, in inches or centimeters.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.7262.1.22.13 |
transmitPowerBackoffOBSOLETE. The transmitter back off power.ro INTEGER .1.3.6.1.4.1.7262.1.22.14 |
apCoS OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.23 |
dot1pFilteringSets DotP1 filtering on/off.rw Enumeration .1.3.6.1.4.1.7262.1.23.1 |
dot1pValue0QueueAssignmentQueue assignment for DotP1 value 0.rw Enumeration .1.3.6.1.4.1.7262.1.23.2 |
dot1pValue1QueueAssignmentQueue assignment for DotP1 value 1.rw Enumeration .1.3.6.1.4.1.7262.1.23.3 |
dot1pValue2QueueAssignmentQueue assignment for DotP1 value 2.rw Enumeration .1.3.6.1.4.1.7262.1.23.4 |
dot1pValue3QueueAssignmentQueue assignment for DotP1 value 3.rw Enumeration .1.3.6.1.4.1.7262.1.23.5 |
dot1pValue4QueueAssignmentQueue assignment for DotP1 value 4.rw Enumeration .1.3.6.1.4.1.7262.1.23.6 |
dot1pValue5QueueAssignmentQueue assignment for DotP1 value 5.rw Enumeration .1.3.6.1.4.1.7262.1.23.7 |
dot1pValue6QueueAssignmentQueue assignment for DotP1 value 6.rw Enumeration .1.3.6.1.4.1.7262.1.23.8 |
dot1pValue7QueueAssignmentQueue assignment for DotP1 value 7.rw Enumeration .1.3.6.1.4.1.7262.1.23.9 |
cosQueueWidthThe class of service queue width. Enter a value from 1 to 16 to define the priority queues size.rw INTEGER .1.3.6.1.4.1.7262.1.23.10 |
apManagementSessions OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24 |
ttySessionUser1 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.1 |
ttySessionUser1NameThe username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.1.1 |
ttySessionUser1ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.1.2 |
ttySessionUser1StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.1.3 |
ttySessionUser2 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.2 |
ttySessionUser2NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.2.1 |
ttySessionUser2ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.2.2 |
ttySessionUser2StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.2.3 |
ttySessionUser3 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.3 |
ttySessionUser3NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.3.1 |
ttySessionUser3ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.3.2 |
ttySessionUser3StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.3.3 |
ttySessionUser4 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.4 |
ttySessionUser4NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.4.1 |
ttySessionUser4ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.4.2 |
ttySessionUser4StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.4.3 |
ttySessionUser5 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.5 |
ttySessionUser5NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.5.1 |
ttySessionUser5ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.5.2 |
ttySessionUser5StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.5.3 |
ttySessionUser6 OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.6 |
ttySessionUser6NameThe username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.6.1 |
ttySessionUser6ConnectionTypeThe physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.6.2 |
ttySessionUser6StateThe state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.ro Enumeration .1.3.6.1.4.1.7262.1.24.6.3 |
sessionUserInterformation OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.24.7 |
ttySessionUserNameNOT IMPLEMENTED. Object type placeholder for username string for SNMP traps. The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system.ro DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.24.7.1 |
ttySessionUserConnectionTypeNOT IMPLEMENTED. Object type placeholder for connection type for SNMP traps. The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.ro Enumeration .1.3.6.1.4.1.7262.1.24.7.2 |
apInstall OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.25 |
apInstallationTypeThe AirPair installation type.
All ODU or IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.25.1 |
apRxCableLossRx cable loss.
Valid only when the installation type is IDU-ODU splitro DisplayString ( SIZE ( 0 .. 100 ) ) .1.3.6.1.4.1.7262.1.25.2 |
apTxCableLossTx cable loss.
Valid only when the installation type is IDU-ODU splitro DisplayString ( SIZE ( 0 .. 100 ) ) .1.3.6.1.4.1.7262.1.25.3 |
apFan1StatusThe fan 1 status.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.25.4 |
apFan2StatusThe fan 2 status.
Valid only when the installation type is IDU-ODU splitro Enumeration .1.3.6.1.4.1.7262.1.25.5 |
apFanTestModeThis operation turns on or off fan test mode.
Fan test mode forces all fans in the system to on.
Valid only when the installation type is IDU-ODU splitrw Enumeration .1.3.6.1.4.1.7262.1.25.6 |
apCableLossChangeCable loss change. Valid only when the installation type
is IDU-ODU splitro DisplayString ( SIZE ( 0 .. 100 ) ) .1.3.6.1.4.1.7262.1.25.7 |
httpSecure OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.27 |
httpSecureCertificateStatusReturns the HTTPS certificate statusro DisplayString ( SIZE ( 0 .. 100 ) ) .1.3.6.1.4.1.7262.1.27.1 |
httpSecureAccessForAdminUsersthe HTTPS access requirement for Admin user group.rw Enumeration .1.3.6.1.4.1.7262.1.27.2 |
httpSecureAccessForNocUsersthe HTTPS access requirement for Noc user group.rw Enumeration .1.3.6.1.4.1.7262.1.27.3 |
httpSecureAccessForSuperUsersthe HTTPS access requirement for Super user group.rw Enumeration .1.3.6.1.4.1.7262.1.27.4 |
gigaEQos OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.28 |
qosEnableIndicates whether gigabit Ethernet QOS is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.28.1 |
dot1pValue0To7VsQueueMappingUser queue assignments for Dot1P values 0 to 7.
Dot1P value 0 is lowest priority and Dot1P value 7
is highest priority. We have 4 user queues. Their corresponding
queue numbers are 1,2, 3, and 4, from lowest priority to highest
priority. The dot1p value to queue number mapping queue
numbers mustbe in an increasing order.
E.g. 1 1 2 2 3 3 4 4 is a valid mapping. 1 2 3 4 2 4 3 1 is NOT.rw DisplayString ( SIZE ( 15 .. 32 ) ) .1.3.6.1.4.1.7262.1.28.2 |
queueOperationModeThis sets the user queue operation mode. (a) In expedite mode,
User Queue 4 has 100% of CIR. User Queue 4 will be serviced
until it is empty. (b) In non expedite mode, the sum of all CIRs
must be equal to 100%. Higher priority queues
will be serviced first until the queues are emptied or
the defined CIRs are reached.rw Enumeration .1.3.6.1.4.1.7262.1.28.3 |
userQueue1To4CIRsCommitteed Information Rate (CIR) assignments for user queues
1 to 4. CIR is the percentage of maximum bandwidth for user
traffic. (a) In queue operation expedite mode, User Queue 1 has
100% of CIR. But CIRs can still be assigned for other queues.
This is because if there is not much traffic for queue 1, CIRs
of other queues can still be observed. However, the sum of
CIRs for queues 2 to 4 should not be greater than 100%. (b) In
queue operation priority mode, the sum of CIRs of user queues 1
to 4 must not be greater than 100%. In cosideration of Qos can be
disabled, or less than 4 user queues can be used, the only condition
to check if CIRs are vaild is that CIRs of used queues must not
be greater than 100%. Example1: 25 25 25 25. Example2: 25 50 25 0.
In example 2, the CIR of queue 1 is 25%, the CIR of queue 2 is 50%,
and CIR of queue 3 is 25%, and CIR of queue 4 is 0.rw DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.28.4 |
userQueue1To4PBSPeak Burst Size (PBS) for user queues 1 to 4. PBS is the percentage
of total user queue packet buffer size. The sum of PBS's of all 4
user queues must not exceed 100%. Example1: 25 25 25 25.
Example 2: 75 25 0 0. In example 2, PBS for queue 1 is 75%, for queue 2
is 25%, and for queue 3 and 4 is 0%.rw DisplayString ( SIZE ( 0 .. 32 ) ) .1.3.6.1.4.1.7262.1.28.5 |
defaultQosValueDefault Qos value is the assigned 802.1p value for the ethernet
frames that don't have dot1p tagged.rw INTEGER (0 .. 7) .1.3.6.1.4.1.7262.1.28.6 |
rapidLinkShutdown OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.29 |
rlsEnableThe Rapid Link Shutdown feature: enabled or disabled.
Changing this option requires a system reset.rw Enumeration .1.3.6.1.4.1.7262.1.29.1 |
automaticLinkReestablishIf this feature is enabled, the link will be automatically reestablihedl
If this feature is disabled, the user must explicitly use the manualReestablish object
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.1.29.2 |
manualLinkReestablishThis object is writeable ONLY if automaticLinkReestablish is set to disabled.
The user explicitly brings the link back up by setting this object to enabled.
The user explicitly brings the link down by setting this object to disabled.
to bring the link back uprw Enumeration .1.3.6.1.4.1.7262.1.29.3 |
hysterisisErredFramesPerMilliSecondThe link will be automatically shut down when this number of erred
modem frames threshold is exceeded during the time set in the
hysterisisErredMilliSeconds object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.1.29.4 |
hysterisisErredMilliSecondsThe time to determine a link that has excessive errors.
The link will be automatically shut down when this number of milliseconds
experiences the number of erred frames specified in the
hysterisisErredFramesPerMilliSecond object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.1.29.5 |
hysterisisUnerredFramesPerMilliSecondThe link will be automatically brought back up when the number of erred
modem frames is less than this value ( only if automaticLinkReestablish
is set to enabled).
This threshold value cannot be crossed for the duration of time specified in the
hysterisisUnerredMilliSeconds object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.1.29.6 |
hysterisisUnerredMilliSecondsThe time block to use to determine if the link is error free enough to
warrant it to automatically reestablish itself ( only if automaticLinkReestablish
is set to enabled).
The link will be brought back up automatically when this number of milliseconds
experiences less the number of acceptable erred frames specified in the
hysterisisUnerredFramesPerMilliSecond object.
**NOTE: You must SET the writeRlsMonitorParametersToSystem object
to write this paramater to RAM. If you write and immediately
read this object, the previous value will be displayed.
You should SET all parameters in this folder first, and then write
to a '1' to the writeRlsMonitorParametersToSystem object.
You must also save the MIB via the writing the apSaveMIB object,
and then reset the system.rw INTEGER .1.3.6.1.4.1.7262.1.29.7 |
writeRlsMonitorParametersToSystemThis writes the following parameters to RAM:
hysterisisErredFramesPerMilliSecond,
hysterisisErredMilliSeconds,
hysterisisUnerredFramesPerMilliSecond,
hysterisisUnerredMilliSeconds.
Reading this object returns '1'.rw INTEGER .1.3.6.1.4.1.7262.1.29.8 |
rlsAdvancedAlgorithmWhen it is on RLS advanced algorithm is used, otherwise
RLS advanced algorithm is not used.rw Enumeration .1.3.6.1.4.1.7262.1.29.9 |
rlsSampleTimeInMilliSecondsrw INTEGER .1.3.6.1.4.1.7262.1.29.10 |
sntp OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.30 |
sntpEnableIndicates whether SNTP feature is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.30.1 |
sntpOffsetSystem time offset from GMT.rw INTEGER ( -140 .. 140 ) .1.3.6.1.4.1.7262.1.30.2 |
sntpServerTableTable containing sntp server entries SEQUENCE OF SntpServerEntry .1.3.6.1.4.1.7262.1.30.3 |
sntpServerEntryContains the sntp server information SntpServerEntry .1.3.6.1.4.1.7262.1.30.3.1 |
sntpServerIndexA unique value for each server.ro INTEGER .1.3.6.1.4.1.7262.1.30.3.1.1 |
sntpServerIpAddressThe IP address of the server.rw IpAddress .1.3.6.1.4.1.7262.1.30.3.1.2 |
sntpServerStatusThe status of the sntp server.ro Enumeration .1.3.6.1.4.1.7262.1.30.3.1.3 |
sntpServerStratumSpecifies the stratum of a server, 0 for failed serverro INTEGER .1.3.6.1.4.1.7262.1.30.3.1.4 |
apLogs OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.31 |
eventLogEnableIndicates whether event log is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.31.1 |
perfmLogEnableIndicates whether performance log is enabled.rw Enumeration .1.3.6.1.4.1.7262.1.31.2 |
perfmLogIntervalPerformance statistics are logged periodically by this interval.rw DisplayString ( SIZE ( 0 .. 10 ) ) .1.3.6.1.4.1.7262.1.31.3 |
radius OBJECT IDENTIFIER .1.3.6.1.4.1.7262.1.32 |
superUserAuthenticationThe set strict mode on or offrw Enumeration .1.3.6.1.4.1.7262.1.32.1 |
serverTimeOutTimeout period for authentication requestsro INTEGER .1.3.6.1.4.1.7262.1.32.2 |
serverDeadTimeTime to declare an unresponsive server 'dead'ro INTEGER .1.3.6.1.4.1.7262.1.32.3 |
serverReTransmitMaximum number of retransmits to an unresponsive serverro Enumeration .1.3.6.1.4.1.7262.1.32.4 |
radiusServerTableTable containing radius server entries SEQUENCE OF RadiusServerEntry .1.3.6.1.4.1.7262.1.32.5 |
radiusServerEntryContains the sntp server information RadiusServerEntry .1.3.6.1.4.1.7262.1.32.5.1 |
radiusServerIndexA unique value for each server.ro INTEGER .1.3.6.1.4.1.7262.1.32.5.1.1 |
cfgdHostIpAddressThe IP address of the configured radius server.rw IpAddress .1.3.6.1.4.1.7262.1.32.5.1.2 |
activeHostIpAddressThe IP address of the active radius server.ro IpAddress .1.3.6.1.4.1.7262.1.32.5.1.3 |
coldStartA coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered. TRAP-TYPE .1.3.6.1.4.1.14125.2.2.16.0.0 |
linkDownA linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration. TRAP-TYPE .1.3.6.1.4.1.14125.2.2.16.0.1 |
linkUpA linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up. TRAP-TYPE .1.3.6.1.4.1.14125.2.2.16.0.2 |