ME1200-ACL-MIB
AI MIB Summary
The ME1200-ACL-MIB facilitates the monitoring and configuration of Access Control List (ACL) entries, including rule definitions, hit counts, and packet statistics, on Cisco ME1200 series Ethernet switches. This private MIB enables granular visibility into traffic filtering policies and security enforcement mechanisms specific to the ME1200 hardware platform.
This is a private MIB for ACL
Main OID:
me1200AclMIB.1.3.6.1.4.1.9.9.815.1.17
226
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
226 total| Object Name |
|---|
me1200AclMIBThis is a private MIB for ACL MODULE-IDENTITY .1.3.6.1.4.1.9.9.815.1.17 |
me1200AclMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1 |
me1200AclConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.2 |
me1200AclGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.2.1 |
me1200AclRateLimiterTableThe ACL rate limiter configuration table. SEQUENCE OF ME1200AclRateLimiterEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1 |
me1200AclRateLimiterEntryEach rate limiter ID has a set of parameters ME1200AclRateLimiterEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1 |
me1200AclRateLimiterIdThe identification of ACL rate limter. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.1 |
me1200AclRateLimiterPacketRateThe packet rate per second. The operation is inactive when bit rate
mode is enabled. Possible values are: 0-99, 100, 2*100, 3*100...,
1092000.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.2 |
me1200AclRateLimiterBitRateThe bit rate per second.The operation is inactive when bit rate mode is
disabled. Possible values are: 0, 100, 2*100, 3*100, ..., 1000000.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.3 |
me1200AclRateLimiterBitRateEnableEnable bit rate.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.1.1.4 |
me1200AclAce OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2 |
me1200AclAceTableThe ACL ACE configuration table. SEQUENCE OF ME1200AclAceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1 |
me1200AclAceEntryEach row contains a set of parameters. ME1200AclAceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1 |
me1200AclAceIdThe identification of ACE. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1 |
me1200AclAceNextAceIdThe next identification for this ACE. Possible values are: 0(end of
list), 1-512.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.2 |
me1200AclAceLookupThe second lookup operation for this ACE. Possible values are:
1(enabled) and 2(disabled).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.3 |
me1200AclAceIngressPortListThe ingress port list for this ACE. Each octet within this value
specifies a set of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16, etc. Within
each octet, the most significant bit represents the lowest numbered
port, and the least significant bit represents the highest numbered
port. Thus, each port of the switch is represented by a single bit
within the value of this object. If that bit has a value of '1' then
that port is included in the set of ports; the port is not included if
its bit has a value of '0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.5 |
me1200AclAcePolicyValueThe policy number for this ACE. The feature is inactive when policy
mask value is non-zero.rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.6 |
me1200AclAcePolicyMaskThe policy number for this ACE. The feature is inactive when policy
mask value is non-zero.rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.7 |
me1200AclAceHitActionThe hit action operation for this ACE. Note all ports will be the
filter port member when filter action is set on the first time.rw ME1200AclAceHitAction .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.8 |
me1200AclAceFilterPortListThe filter port list. It is active only when the hit action is
filtered. Set the action value to 0(filter) before the new setting.
Note that the action will change deny action if there is no any port in
the member set. Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through 8, the second
octet specifying ports 9 through 16, etc. Within each octet, the most
significant bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each port
of the switch is represented by a single bit within the value of this
object. If that bit has a value of '1' then that port is included in
the set of ports; the port is not included if its bit has a value of
'0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.9 |
me1200AclAceRateLimiterIdThe rate limiter ID. Possible values are: 0(disabled), 1-16.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.10 |
me1200AclAceEvcPolicerIdThe EVC policer ID. Possible values are: 0(disabled), 1-1022.rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.11 |
me1200AclAceRedirectPortListThe ingress port list for this ACE. It is active only when the hit
action is denied. Set the action value to 1(deny) before the new
setting. Set value 0 to disable the opertion. Each octet within this
value specifies a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the lowest
numbered port, and the least significant bit represents the highest
numbered port. Thus, each port of the switch is represented by a single
bit within the value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port is not
included if its bit has a value of '0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.12 |
me1200AclAceMirrorThe rmirror operation. Frames matching this ACE are mirrored to the
destination mirror port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.13 |
me1200AclAceLoggingThe logging operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.14 |
me1200AclAceShutdownThe shutdown operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.15 |
me1200AclAceVlanTaggedThe 802.1Q VLAN tagged for this ACE.rw ME1200VlanTagged .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.100 |
me1200AclAceVlanIdThe VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.101 |
me1200AclAceVlanTagPriorityThe VLN tag priority for this ACE. Enable VLAN tagged filter before the
new setting.rw ME1200VlanTagPriority .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.102 |
me1200AclAceFrameTypeThe frame type for this ACE.rw ME1200AclAceType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.200 |
me1200AclAceEtypeSrcMacOpIndicates how a Ethernet type packet's source MAC address is to be
compared. This object can only be configured if FrameType is etype(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.300 |
me1200AclAceEtypeSrcMacIndicates the 48 bits source MAC address. This object can only be
configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.301 |
me1200AclAceEtypeDestMacOpIndicates how a Ethernet type packet's destination MAC address is to be
compared. This object can only be configured if FrameType is etype(1).rw ME1200AdvDestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.302 |
me1200AclAceEtypeDestMacIndicates the 48 bits destination MAC address. This object can only be
configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.303 |
me1200AclAceEtypeIndicates the packet's 16 bit Ethernet type field. Possible values are:
0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and
0x86DD(IPv6).This object can only be configured if FrameType is
etype(1) and EtypeDestMacOp is specific(1).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.304 |
me1200AclAceArpSrcMacOpIndicates how a ARP packet's source MAC address is to be compared. This
object can only be configured if FrameType is arp(4).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.600 |
me1200AclAceArpSrcMacIndicates the 48 bits source MAC address. This object can only be
configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.601 |
me1200AclAceArpDestMacOpIndicates how a ARP packet's destination MAC address is to be compared.
This object can only be configured if FrameType is arp(4).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.602 |
me1200AclAceArpSenderIpThe specified ARP sender IP address. The packets sender address is
AND-ed with the value of ArpSenderIpMask and then compared with the
value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this
entry matches any sender IP address. This object can only be configured
if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.603 |
me1200AclAceArpSenderIpMaskThe specified ARP sender IP address mask. This object can only be
configured if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.604 |
me1200AclAceArpTragetIpThe specified ARP target IP address. The packets target address is
AND-ed with the value of ArpTragetIpMask and then compared with the
value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this
entry matches any target IP address. This object can only be configured
if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.605 |
me1200AclAceArpTragetIpMaskThe specified ARP target IP address mask. This object can only be
configured if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.606 |
me1200AclAceArpOpcodeIndicates how a ARP packet's opcode is to be compared. This object can
only be configured if FrameType is arp(4).rw ME1200ArpOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.607 |
me1200AclAceArpFlagRequestIndicates how a ARP packet's request/reply opcode is to be compared.
The value 0 means any ARP opcode is allowed (don't-care field), value 1
means ARP opcode is equal to request opcode and value 2 means ARP
opcode is equal to reply opcode. This object can only be configured if
FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.608 |
me1200AclAceArpFlagSenderMacIndicates how a ARP packet's sender hardware address field (SHA) is to
be compared. The value 0 means any SHA value is allowed (don't-care
field), value 1 means SHA is not equal to the SMAC address and value 2
means SHA is equal to the SMAC address. This object can only be
configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.609 |
me1200AclAceArpFlagTargetMacIndicates how a ARP packet's target hardware address field (THA) is to
be compared. The value 0 means any THA value is allowed (don't-care
field), value 1 means THA is not equal to the DMAC address and value 2
means THA is equal to the DMAC address. This object can only be
configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.610 |
me1200AclAceArpFlagLenIndicates how a ARP packet's s hardware address length field (HLN) is
to be compared. The value 0 means any HLN value is allowed (don't-care
field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN)
is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet
(0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only
be configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.611 |
me1200AclAceArpFlagIpIndicates how a ARP packet's hardware address space field (HRD) is to
be compared. The value 0 means any HRD value is allowed (don't-care
field), value 1 means HRD is not equal to Ethernet (1) and value 2
means HRD is equal to Ethernet (1). This object can only be configured
if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.612 |
me1200AclAceArpFlagEthernetIndicates how a ARP packet's protocol address space field (PRO) is to
be compared. The value 0 means any PRO value is allowed (don't-care
field), value 1 means PRO is not equal to IP (0x800) and value 2 means
PRO is equal to IP (0x800). This object can only be configured if
FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.613 |
me1200AclAceIpv4DestMacOpIndicates how a IPv4 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is ipv4(5).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.700 |
me1200AclAceIpv4ProtocolOpIndicates how a IPv4 packet's protocol field is to be compared. This
object can only be configured if FrameType is ipv4(5).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.701 |
me1200AclAceIpv4ProtocolThe protocol number field in the IPv4 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.702 |
me1200AclAceIpv4FlagTtlIndicates how a IPv4 packet's Time-to-Live field (TTL) is to be
compared. The value 0 means any TTL value is allowed (don't-care
field), value 1 means TTL is not equal zero and value 2 means TTL is
equal to zero. This object can only be configured if FrameType is
ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.703 |
me1200AclAceIpv4FlagFragmentIndicates how a IPv4 packet's More-Fragments field (MF) is to be
compared. The value 0 means any MF value is allowed (don't-care field),
value 1 means MF is not equal one (MF field isn't set) and value 2
means MF is equal to one (MF field is set). This object can only be
configured if FrameType is ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.704 |
me1200AclAceIpv4FlagIpOptionIndicates how a IPv4 packet's options field is to be compared. The
value 0 means any options is allowed (don't-care field), value 1 means
options is not equal one (options field isn't set) and value 2 means
options is equal to one (options field is set). This object can only be
configured if FrameType is ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.705 |
me1200AclAceIpv4SrcIpThe specified source IPv4 address. The packets sender address is AND-ed
with the value of Ipv4SrcIpMask and then compared with the value of
this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry
matches any source IP address. This object can only be configured if
FrameType is ipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.706 |
me1200AclAceIpv4SrcIpMaskThe specified source IPv4 address mask. This object can only be
configured if FrameType isipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.707 |
me1200AclAceIpv4DestIpThe specified destination IPv4 address. The packets sender address is
AND-ed with the value of Ipv4DestIpMask and then compared with the
value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0,
this entry matches any destination IP address. This object can only be
configured if FrameType is ipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.708 |
me1200AclAceIpv4DestIpMaskThe specified destination IPv4 address mask. This object can only be
configured if FrameType isipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.709 |
me1200AclAceIpv4IcmpTypeOpIndicates how a IPv4 packet's ICMP type field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.710 |
me1200AclAceIpv4IcmpTypeThe ICMP type field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpTypeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.711 |
me1200AclAceIpv4IcmpCodeOpIndicates how a IPv4 packet's ICMP code field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.712 |
me1200AclAceIpv4IcmpCodeThe ICMP code field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpCodeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.713 |
me1200AclAceIpv4SrcPortOpIndicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv4(5).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.714 |
me1200AclAceIpv4SrcPortThe source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid range is 0-65535. This object can
only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not
any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.715 |
me1200AclAceIpv4SrcPortRangeThe source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid range is 0-65535. This object can only
be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.716 |
me1200AclAceIpv4DestPortOpIndicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv4(5).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.717 |
me1200AclAceIpv4DestPortThe destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. Valid range is 0-65535.
This object can only be configured if FrameType is ipv4(5) and
Ipv4DestPortOp is not any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.718 |
me1200AclAceIpv4DestPortRangeThe destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Valid range is 0-65535. This
object can only be configured if FrameType is ipv4(5) and
Ipv4DestPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.719 |
me1200AclAceIpv4TcpFlagFinIndicates how a IPv4 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not equal one (FIN field isn't
set) and value 2 means FIN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.720 |
me1200AclAceIpv4TcpFlagSynIndicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is not equal one (FIN field isn't
set) and value 2 means SYN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.721 |
me1200AclAceIpv4TcpFlagRstIndicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equal one (FIN field isn't set) and
value 2 means RST is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.722 |
me1200AclAceIpv4TcpFlagPshIndicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one (FIN field isn't set) and
value 2 means PSH is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.723 |
me1200AclAceIpv4TcpFlagAckIndicates how a IPv4 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means ACK is not equal one (FIN
field isn't set) and value 2 means ACK is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.724 |
me1200AclAceIpv4TcpFlagUrgIndicates how a IPv4 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means URG is not equal one (FIN
field isn't set) and value 2 means URG is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.725 |
me1200AclAceIPv6DestMacOpIndicates how a IPv6 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is arp(4).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.800 |
me1200AclAceIpv6NextHeaderOpIndicates how a IPv6 packet's next header field is to be compared. This
object can only be configured if FrameType is ipv6(6).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.801 |
me1200AclAceIpv6NextHeaderThe next header field in the IPv6 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.802 |
me1200AclAceIpv6SrcIpThe specified IPv6 source address. The packets source address is AND-ed
with the value of Ipv6SrcIpMask and then compared with the value of
this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry
matches any IPv6 source address. Only the least significant 32 bits of
this object are used. This object can only be configured if FrameType
is ipv6(6) and Ipv6SrcIpMask is not all zeros.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.803 |
me1200AclAceIpv6SrcIpMaskThe specified IPv6 source address mask. Only the least significant 32
bits of this object are used. This object can only be configured if
FrameType is ipv6(6).rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.804 |
me1200AclAceIpv6FlagHopLimiterIndicates how a IPv6 packet's hop limit field is to be compared. The
value 0 means any hop limit value is allowed (don't-care field), value
1 means hop limit is not equal zero and value 2 means hop limit is
equal to zero. This object can only be configured if FrameType is
ipv6(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.805 |
me1200AclAceIpv6Icmpv6TypeOpIndicates how a IPv6 packet's ICMPv6 type field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.806 |
me1200AclAceIpv6Icmpv6TypeThe ICMPv6 type field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.807 |
me1200AclAceIpv6Icmpv6CodeOpIndicates how a IPv6 packet's ICMPv6 code field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.808 |
me1200AclAceIpv6Icmpv6CodeThe ICMPv6 code field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.809 |
me1200AclAceIpv6SrcPortOpIndicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv6(6).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.810 |
me1200AclAceIpv6SrcPortThe source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid range is 0-65535. This object can
only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not
any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.811 |
me1200AclAceIpv6SrcPortRangeThe source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid range is 0-65535. This object can only
be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.812 |
me1200AclAceIpv6DestPortOpIndicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv6(6).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.813 |
me1200AclAceIpv6DestPortThe destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. Valid range is 0-65535.
This object can only be configured if FrameType is ipv6(6) and
Ipv6DestPortOp is not any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.814 |
me1200AclAceIpv6DestPortRangeThe destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Valid range is 0-65535. This
object can only be configured if FrameType is ipv6(6) and
Ipv6DestPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.815 |
me1200AclAceIpv6TcpFlagFinIndicates how a IPv6 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not equal one (FIN field isn't
set) and value 2 means FIN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.816 |
me1200AclAceIpv6TcpFlagSynIndicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is not equal one (FIN field isn't
set) and value 2 means SYN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.817 |
me1200AclAceIpv6TcpFlagRstIndicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equal one (FIN field isn't set) and
value 2 means RST is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.818 |
me1200AclAceIpv6TcpFlagPshIndicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one (FIN field isn't set) and
value 2 means PSH is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.819 |
me1200AclAceIpv6TcpFlagAckIndicates how a IPv6 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means ACK is not equal one (FIN
field isn't set) and value 2 means ACK is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.820 |
me1200AclAceIpv6TcpFlagUrgIndicates how a IPv6 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means URG is not equal one (FIN
field isn't set) and value 2 means URG is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.821 |
me1200AclAceActionActionrw ME1200RowEditorState (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.1.1.1000 |
me1200AclAceTableRowEditor OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2 |
me1200AclAceTableRowEditorIdThe identification of ACE.rw Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1 |
me1200AclAceTableRowEditorNextAceIdThe next identification for this ACE. Possible values are: 0(end of
list), 1-512.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.2 |
me1200AclAceTableRowEditorLookupThe second lookup operation for this ACE. Possible values are:
1(enabled) and 2(disabled).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.3 |
me1200AclAceTableRowEditorIngressPortListThe ingress port list for this ACE. Each octet within this value
specifies a set of eight ports, with the first octet specifying ports 1
through 8, the second octet specifying ports 9 through 16, etc. Within
each octet, the most significant bit represents the lowest numbered
port, and the least significant bit represents the highest numbered
port. Thus, each port of the switch is represented by a single bit
within the value of this object. If that bit has a value of '1' then
that port is included in the set of ports; the port is not included if
its bit has a value of '0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.5 |
me1200AclAceTableRowEditorPolicyValueThe policy number for this ACE. The feature is inactive when policy
mask value is non-zero.rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.6 |
me1200AclAceTableRowEditorPolicyMaskThe policy number for this ACE. The feature is inactive when policy
mask value is non-zero.rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.7 |
me1200AclAceTableRowEditorHitActionThe hit action operation for this ACE. Note all ports will be the
filter port member when filter action is set on the first time.rw ME1200AclAceHitAction .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.8 |
me1200AclAceTableRowEditorFilterPortListThe filter port list. It is active only when the hit action is
filtered. Set the action value to 0(filter) before the new setting.
Note that the action will change deny action if there is no any port in
the member set. Each octet within this value specifies a set of eight
ports, with the first octet specifying ports 1 through 8, the second
octet specifying ports 9 through 16, etc. Within each octet, the most
significant bit represents the lowest numbered port, and the least
significant bit represents the highest numbered port. Thus, each port
of the switch is represented by a single bit within the value of this
object. If that bit has a value of '1' then that port is included in
the set of ports; the port is not included if its bit has a value of
'0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.9 |
me1200AclAceTableRowEditorRateLimiterIdThe rate limiter ID. Possible values are: 0(disabled), 1-16.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.10 |
me1200AclAceTableRowEditorEvcPolicerIdThe EVC policer ID. Possible values are: 0(disabled), 1-1022.rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.11 |
me1200AclAceTableRowEditorRedirectPortListThe ingress port list for this ACE. It is active only when the hit
action is denied. Set the action value to 1(deny) before the new
setting. Set value 0 to disable the opertion. Each octet within this
value specifies a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the lowest
numbered port, and the least significant bit represents the highest
numbered port. Thus, each port of the switch is represented by a single
bit within the value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port is not
included if its bit has a value of '0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.12 |
me1200AclAceTableRowEditorMirrorThe rmirror operation. Frames matching this ACE are mirrored to the
destination mirror port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.13 |
me1200AclAceTableRowEditorLoggingThe logging operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.14 |
me1200AclAceTableRowEditorShutdownThe shutdown operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.15 |
me1200AclAceTableRowEditorVlanTaggedThe 802.1Q VLAN tagged for this ACE.rw ME1200VlanTagged .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.100 |
me1200AclAceTableRowEditorVlanIdThe VLAN ID for this ACE. Possible values are: 0(disabled), 1-4095.rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.101 |
me1200AclAceTableRowEditorVlanTagPriorityThe VLN tag priority for this ACE. Enable VLAN tagged filter before the
new setting.rw ME1200VlanTagPriority .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.102 |
me1200AclAceTableRowEditorFrameTypeThe frame type for this ACE.rw ME1200AclAceType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.200 |
me1200AclAceTableRowEditorEtypeSrcMacOpIndicates how a Ethernet type packet's source MAC address is to be
compared. This object can only be configured if FrameType is etype(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.300 |
me1200AclAceTableRowEditorEtypeSrcMacIndicates the 48 bits source MAC address. This object can only be
configured if FrameType is etype(1) and EtypeSrcMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.301 |
me1200AclAceTableRowEditorEtypeDestMacOpIndicates how a Ethernet type packet's destination MAC address is to be
compared. This object can only be configured if FrameType is etype(1).rw ME1200AdvDestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.302 |
me1200AclAceTableRowEditorEtypeDestMacIndicates the 48 bits destination MAC address. This object can only be
configured if FrameType is etype(1) and EtypeDestMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.303 |
me1200AclAceTableRowEditorEtypeIndicates the packet's 16 bit Ethernet type field. Possible values are:
0(disabled), 0x600-0xFFFF but excluding 0x800(IPv4), 0x806(ARP) and
0x86DD(IPv6).This object can only be configured if FrameType is
etype(1) and EtypeDestMacOp is specific(1).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.304 |
me1200AclAceTableRowEditorArpSrcMacOpIndicates how a ARP packet's source MAC address is to be compared. This
object can only be configured if FrameType is arp(4).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.600 |
me1200AclAceTableRowEditorArpSrcMacIndicates the 48 bits source MAC address. This object can only be
configured if FrameType is arp(4) and ArpSrcMacOp is specific(1).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.601 |
me1200AclAceTableRowEditorArpDestMacOpIndicates how a ARP packet's destination MAC address is to be compared.
This object can only be configured if FrameType is arp(4).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.602 |
me1200AclAceTableRowEditorArpSenderIpThe specified ARP sender IP address. The packets sender address is
AND-ed with the value of ArpSenderIpMask and then compared with the
value of this object. If ArpSenderIp and ArpSrcIpMask are 0.0.0.0, this
entry matches any sender IP address. This object can only be configured
if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.603 |
me1200AclAceTableRowEditorArpSenderIpMaskThe specified ARP sender IP address mask. This object can only be
configured if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.604 |
me1200AclAceTableRowEditorArpTragetIpThe specified ARP target IP address. The packets target address is
AND-ed with the value of ArpTragetIpMask and then compared with the
value of this object. If ArpTragetIp and ArpSrcIpMask are 0.0.0.0, this
entry matches any target IP address. This object can only be configured
if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.605 |
me1200AclAceTableRowEditorArpTragetIpMaskThe specified ARP target IP address mask. This object can only be
configured if FrameType is arp(4).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.606 |
me1200AclAceTableRowEditorArpOpcodeIndicates how a ARP packet's opcode is to be compared. This object can
only be configured if FrameType is arp(4).rw ME1200ArpOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.607 |
me1200AclAceTableRowEditorArpFlagRequestIndicates how a ARP packet's request/reply opcode is to be compared.
The value 0 means any ARP opcode is allowed (don't-care field), value 1
means ARP opcode is equal to request opcode and value 2 means ARP
opcode is equal to reply opcode. This object can only be configured if
FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.608 |
me1200AclAceTableRowEditorArpFlagSenderMacIndicates how a ARP packet's sender hardware address field (SHA) is to
be compared. The value 0 means any SHA value is allowed (don't-care
field), value 1 means SHA is not equal to the SMAC address and value 2
means SHA is equal to the SMAC address. This object can only be
configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.609 |
me1200AclAceTableRowEditorArpFlagTargetMacIndicates how a ARP packet's target hardware address field (THA) is to
be compared. The value 0 means any THA value is allowed (don't-care
field), value 1 means THA is not equal to the DMAC address and value 2
means THA is equal to the DMAC address. This object can only be
configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.610 |
me1200AclAceTableRowEditorArpFlagLenIndicates how a ARP packet's s hardware address length field (HLN) is
to be compared. The value 0 means any HLN value is allowed (don't-care
field), value 1 means HLN is not equal to Ethernet (0x06) or the (PLN)
is not equal to IPv4 (0x04) and value 2 means HLN is equal to Ethernet
(0x06) or the (PLN) is not equal to IPv4 (0x04). This object can only
be configured if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.611 |
me1200AclAceTableRowEditorArpFlagIpIndicates how a ARP packet's hardware address space field (HRD) is to
be compared. The value 0 means any HRD value is allowed (don't-care
field), value 1 means HRD is not equal to Ethernet (1) and value 2
means HRD is equal to Ethernet (1). This object can only be configured
if FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.612 |
me1200AclAceTableRowEditorArpFlagEthernetIndicates how a ARP packet's protocol address space field (PRO) is to
be compared. The value 0 means any PRO value is allowed (don't-care
field), value 1 means PRO is not equal to IP (0x800) and value 2 means
PRO is equal to IP (0x800). This object can only be configured if
FrameType is arp(4).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.613 |
me1200AclAceTableRowEditorIpv4DestMacOpIndicates how a IPv4 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is ipv4(5).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.700 |
me1200AclAceTableRowEditorIpv4ProtocolOpIndicates how a IPv4 packet's protocol field is to be compared. This
object can only be configured if FrameType is ipv4(5).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.701 |
me1200AclAceTableRowEditorIpv4ProtocolThe protocol number field in the IPv4 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv4(5) and Ipv4ProtocolOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.702 |
me1200AclAceTableRowEditorIpv4FlagTtlIndicates how a IPv4 packet's Time-to-Live field (TTL) is to be
compared. The value 0 means any TTL value is allowed (don't-care
field), value 1 means TTL is not equal zero and value 2 means TTL is
equal to zero. This object can only be configured if FrameType is
ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.703 |
me1200AclAceTableRowEditorIpv4FlagFragmentIndicates how a IPv4 packet's More-Fragments field (MF) is to be
compared. The value 0 means any MF value is allowed (don't-care field),
value 1 means MF is not equal one (MF field isn't set) and value 2
means MF is equal to one (MF field is set). This object can only be
configured if FrameType is ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.704 |
me1200AclAceTableRowEditorIpv4FlagIpOptionIndicates how a IPv4 packet's options field is to be compared. The
value 0 means any options is allowed (don't-care field), value 1 means
options is not equal one (options field isn't set) and value 2 means
options is equal to one (options field is set). This object can only be
configured if FrameType is ipv4(5).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.705 |
me1200AclAceTableRowEditorIpv4SrcIpThe specified source IPv4 address. The packets sender address is AND-ed
with the value of Ipv4SrcIpMask and then compared with the value of
this object. If Ipv4SrcIp and Ipv4SrcIpMask are 0.0.0.0, this entry
matches any source IP address. This object can only be configured if
FrameType is ipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.706 |
me1200AclAceTableRowEditorIpv4SrcIpMaskThe specified source IPv4 address mask. This object can only be
configured if FrameType isipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.707 |
me1200AclAceTableRowEditorIpv4DestIpThe specified destination IPv4 address. The packets sender address is
AND-ed with the value of Ipv4DestIpMask and then compared with the
value of this object. If Ipv4DestIp and Ipv4DestIpMask are 0.0.0.0,
this entry matches any destination IP address. This object can only be
configured if FrameType is ipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.708 |
me1200AclAceTableRowEditorIpv4DestIpMaskThe specified destination IPv4 address mask. This object can only be
configured if FrameType isipv4(5).rw IpAddress .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.709 |
me1200AclAceTableRowEditorIpv4IcmpTypeOpIndicates how a IPv4 packet's ICMP type field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.710 |
me1200AclAceTableRowEditorIpv4IcmpTypeThe ICMP type field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpTypeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.711 |
me1200AclAceTableRowEditorIpv4IcmpCodeOpIndicates how a IPv4 packet's ICMP code field is to be compared. This
object can only be configured if FrameType is ipv4(5) and Ipv4Protocol
is icmp(1).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.712 |
me1200AclAceTableRowEditorIpv4IcmpCodeThe ICMP code field in the IPv4 header. Possible values are 0-255.This
object can only be configured if FrameType is ipv4(5), Ipv4Protocol is
icmp(1) and Ipv4IcmpCodeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.713 |
me1200AclAceTableRowEditorIpv4SrcPortOpIndicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv4(5).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.714 |
me1200AclAceTableRowEditorIpv4SrcPortThe source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid range is 0-65535. This object can
only be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is not
any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.715 |
me1200AclAceTableRowEditorIpv4SrcPortRangeThe source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid range is 0-65535. This object can only
be configured if FrameType is ipv4(5) and Ipv4SrcPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.716 |
me1200AclAceTableRowEditorIpv4DestPortOpIndicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv4(5).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.717 |
me1200AclAceTableRowEditorIpv4DestPortThe destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. Valid range is 0-65535.
This object can only be configured if FrameType is ipv4(5) and
Ipv4DestPortOp is not any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.718 |
me1200AclAceTableRowEditorIpv4DestPortRangeThe destination port number of the TCP or UDP protocol. If the
Ipv4DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Valid range is 0-65535. This
object can only be configured if FrameType is ipv4(5) and
Ipv4DestPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.719 |
me1200AclAceTableRowEditorIpv4TcpFlagFinIndicates how a IPv4 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not equal one (FIN field isn't
set) and value 2 means FIN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.720 |
me1200AclAceTableRowEditorIpv4TcpFlagSynIndicates how a IPv4 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is not equal one (FIN field isn't
set) and value 2 means SYN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.721 |
me1200AclAceTableRowEditorIpv4TcpFlagRstIndicates how a IPv4 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equal one (FIN field isn't set) and
value 2 means RST is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.722 |
me1200AclAceTableRowEditorIpv4TcpFlagPshIndicates how a IPv4 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one (FIN field isn't set) and
value 2 means PSH is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv4(5) and Ipv4ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.723 |
me1200AclAceTableRowEditorIpv4TcpFlagAckIndicates how a IPv4 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means ACK is not equal one (FIN
field isn't set) and value 2 means ACK is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.724 |
me1200AclAceTableRowEditorIpv4TcpFlagUrgIndicates how a IPv4 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means URG is not equal one (FIN
field isn't set) and value 2 means URG is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv4(5) and
Ipv4ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.725 |
me1200AclAceTableRowEditorIPv6DestMacOpIndicates how a IPv6 packet's destination MAC address is to be
compared. This object can only be configured if FrameType is arp(4).rw ME1200DestMacType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.800 |
me1200AclAceTableRowEditorIpv6NextHeaderOpIndicates how a IPv6 packet's next header field is to be compared. This
object can only be configured if FrameType is ipv6(6).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.801 |
me1200AclAceTableRowEditorIpv6NextHeaderThe next header field in the IPv6 header used to indicate a higher
layer protocol. Possible values are 0-255.This object can only be
configured if FrameType is ipv6(6) and Ipv6NextHeaderOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.802 |
me1200AclAceTableRowEditorIpv6SrcIpThe specified IPv6 source address. The packets source address is AND-ed
with the value of Ipv6SrcIpMask and then compared with the value of
this object. If Ipv6SrcIp and Ipv6SrcIpMask are all zeros, this entry
matches any IPv6 source address. Only the least significant 32 bits of
this object are used. This object can only be configured if FrameType
is ipv6(6) and Ipv6SrcIpMask is not all zeros.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.803 |
me1200AclAceTableRowEditorIpv6SrcIpMaskThe specified IPv6 source address mask. Only the least significant 32
bits of this object are used. This object can only be configured if
FrameType is ipv6(6).rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.804 |
me1200AclAceTableRowEditorIpv6FlagHopLimiterIndicates how a IPv6 packet's hop limit field is to be compared. The
value 0 means any hop limit value is allowed (don't-care field), value
1 means hop limit is not equal zero and value 2 means hop limit is
equal to zero. This object can only be configured if FrameType is
ipv6(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.805 |
me1200AclAceTableRowEditorIpv6Icmpv6TypeOpIndicates how a IPv6 packet's ICMPv6 type field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.806 |
me1200AclAceTableRowEditorIpv6Icmpv6TypeThe ICMPv6 type field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6TypeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.807 |
me1200AclAceTableRowEditorIpv6Icmpv6CodeOpIndicates how a IPv6 packet's ICMPv6 code field is to be compared. This
object can only be configured if FrameType is ipv6(6) and
Ipv6NextHeader is icmpv6(58).rw ME1200ASType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.808 |
me1200AclAceTableRowEditorIpv6Icmpv6CodeThe ICMPv6 code field in the IPv6 header. Possible values are
0-255.This object can only be configured if FrameType is ipv6(6),
Ipv6NextHeader is icmpv6(58) and Ipv6Icmpv6CodeOp is specific(1).rw ME1200Unsigned8 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.809 |
me1200AclAceTableRowEditorIpv6SrcPortOpIndicates how a packet's source TCP/UDP port number is to be compared.
This object can only be configured if FrameType is ipv6(6).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.810 |
me1200AclAceTableRowEditorIpv6SrcPortThe source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the starting
port number of the port range. Valid range is 0-65535. This object can
only be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is not
any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.811 |
me1200AclAceTableRowEditorIpv6SrcPortRangeThe source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp
object in the same row is range(2), this object will be the ending port
number of the port range. Valid range is 0-65535. This object can only
be configured if FrameType is ipv6(6) and Ipv6SrcPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.812 |
me1200AclAceTableRowEditorIpv6DestPortOpIndicates how a packet's destination TCP/UDP port number is to be
compared. This object can only be configured if FrameType is ipv6(6).rw ME1200ASRType .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.813 |
me1200AclAceTableRowEditorIpv6DestPortThe destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the starting port number of the port range. Valid range is 0-65535.
This object can only be configured if FrameType is ipv6(6) and
Ipv6DestPortOp is not any(0).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.814 |
me1200AclAceTableRowEditorIpv6DestPortRangeThe destination port number of the TCP or UDP protocol. If the
Ipv6DestPortOp object in the same row is range(2), this object will be
the ending port number of the port range. Valid range is 0-65535. This
object can only be configured if FrameType is ipv6(6) and
Ipv6DestPortOp is range(2).rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.815 |
me1200AclAceTableRowEditorIpv6TcpFlagFinIndicates how a IPv6 TCP packet's 'No more data from sender' field
(FIN) is to be compared. The value 0 means any FIN value is allowed
(don't-care field), value 1 means FIN is not equal one (FIN field isn't
set) and value 2 means FIN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.816 |
me1200AclAceTableRowEditorIpv6TcpFlagSynIndicates how a IPv6 TCP packet's 'Synchronize sequence numbers' field
(SYN) is to be compared. The value 0 means any SYN value is allowed
(don't-care field), value 1 means SYN is not equal one (FIN field isn't
set) and value 2 means SYN is equal to one (FIN field is set). This
object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.817 |
me1200AclAceTableRowEditorIpv6TcpFlagRstIndicates how a IPv6 TCP packet's 'Reset the connection' field (RST) is
to be compared. The value 0 means any RST value is allowed (don't-care
field), value 1 means RST is not equal one (FIN field isn't set) and
value 2 means RST is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.818 |
me1200AclAceTableRowEditorIpv6TcpFlagPshIndicates how a IPv6 TCP packet's 'Push Function' field (PSH) is to be
compared. The value 0 means any PSH value is allowed (don't-care
field), value 1 means PSH is not equal one (FIN field isn't set) and
value 2 means PSH is equal to one (FIN field is set). This object can
only be configured if FrameType is ipv6(6) and Ipv6ProtocolType is
tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.819 |
me1200AclAceTableRowEditorIpv6TcpFlagAckIndicates how a IPv6 TCP packet's 'Acknowledgment field significant'
field (ACK) is to be compared. The value 0 means any FIN value is
allowed (don't-care field), value 1 means ACK is not equal one (FIN
field isn't set) and value 2 means ACK is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.820 |
me1200AclAceTableRowEditorIpv6TcpFlagUrgIndicates how a IPv6 TCP packet's 'Urgent Pointer field significant'
field (URG) is to be compared. The value 0 means any URG value is
allowed (don't-care field), value 1 means URG is not equal one (FIN
field isn't set) and value 2 means URG is equal to one (FIN field is
set). This object can only be configured if FrameType is ipv6(6) and
Ipv6ProtocolType is tcp(6).rw ME1200AclAceFlagOpcode .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.821 |
me1200AclAceTableRowEditorActionActionrw ME1200RowEditorState (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.2.1000 |
me1200AclAcePrecedenceTableThis table provides an overview of ACE by hit precedence. SEQUENCE OF ME1200AclAcePrecedenceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3 |
me1200AclAcePrecedenceEntryEach row contains a set of parameters. ME1200AclAcePrecedenceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1 |
me1200AclAcePrecedencePrecedenceIndexThe ACL ACE hit precedence. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.1 |
me1200AclAcePrecedenceAceIdThe identification for this ACE. Possible values are: 0(end of list),
1-512.ro Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.1.2.3.1.2 |
me1200AclInterface OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.2.2 |
me1200AclInterfaceTableThe ACL interface configuration table. SEQUENCE OF ME1200AclInterfaceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1 |
me1200AclInterfaceEntryEach interface has a set of parameters ME1200AclInterfaceEntry .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1 |
me1200AclInterfaceIfIndexThe index of logical interface, it is as well as the IF-MIB [RFC2863]
objects ifIndex. ME1200InterfaceIndex (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.1 |
me1200AclInterfacePolicyIdThe policy ID. Possible values are: 0-63.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.2 |
me1200AclInterfaceHitActionThe hit action.rw ME1200AclInterfaceHitAction .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.3 |
me1200AclInterfaceRateLimiterIdThe rate limiter ID. Possible values are: 0(disabled), 1-16.rw Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.4 |
me1200AclInterfaceEvcPolicerIdThe EVC policer ID. Possible values are: 0(disabled), 1-1022.rw ME1200Unsigned16 (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.5 |
me1200AclInterfaceRedirectPortListThe ingress port list for this ACE. It is active only when the hit
action is denied. Set the action value to 1(deny) before the new
setting. Set value 0 to disable the opertion. Each octet within this
value specifies a set of eight ports, with the first octet specifying
ports 1 through 8, the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the lowest
numbered port, and the least significant bit represents the highest
numbered port. Thus, each port of the switch is represented by a single
bit within the value of this object. If that bit has a value of '1'
then that port is included in the set of ports; the port is not
included if its bit has a value of '0'.rw ME1200PortList (ME1200-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.6 |
me1200AclInterfaceMirrorThe rmirror operation. Frames matching this ACE are mirrored to the
destination mirror port.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.7 |
me1200AclInterfaceLoggingThe logging operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.8 |
me1200AclInterfaceShutdownThe shutdown operation.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.9 |
me1200AclInterfaceStateThe port state of this interface.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.2.2.1.1.10 |
me1200AclStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.3 |
me1200AclStatusGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.3.1 |
me1200AclAceStatusTableThis table provides the ACE status in the hardware table. SEQUENCE OF ME1200AclAceStatusEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1 |
me1200AclAceStatusEntryEach row contains a set of parameters. ME1200AclAceStatusEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1 |
me1200AclAceStatusPrecedenceIndexThe ACL ACE hit precedence. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.2 |
me1200AclAceStatusUserThe application user of ACL.ro ME1200AclUser .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.3 |
me1200AclAceStatusAceIdThe identification for this ACE. Possible values are: 0(end of list),
1-512.ro Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.4 |
me1200AclAceStatusConflictThe conflict status of this ACE. When the status value is 1(true), it
means the specific ACE is not applied to the hardware due to hardware
limitations.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.3.1.1.1.5 |
me1200AclAceHitCountTableThe ACL ACE hit count table. SEQUENCE OF ME1200AclAceHitCountEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.1.2 |
me1200AclAceHitCountEntryEach row has the hit count of ACE ME1200AclAceHitCountEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1 |
me1200AclAceHitCountAceIdThe identification of ACE. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.1 |
me1200AclAceHitCountHitCountThe hit count of this ACE.ro Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.3.1.2.1.2 |
me1200AclStatusInterface OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.3.2 |
me1200AclInterfaceHitCountTableThe ACL interface hit count table. SEQUENCE OF ME1200AclInterfaceHitCountEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.2.1 |
me1200AclInterfaceHitCountEntryEach row has the hit count of interface ME1200AclInterfaceHitCountEntry .1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1 |
me1200AclInterfaceHitCountIdThe identification of ACE. Integer32 .1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.1 |
me1200AclInterfaceHitCountHitCountThe hit count of this interface. The hit count will be increased if the
incoming frame doesn't hit any ACEs.ro Unsigned32 .1.3.6.1.4.1.9.9.815.1.17.1.3.2.1.1.2 |
me1200AclControl OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.4 |
me1200AclControlGlobals OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.1.4.1 |
me1200AclControlGlobalsClearAllHitCountThe operation is active when the value is set to 'ture(1)'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.815.1.17.1.4.1.1 |
me1200AclMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.3 |
me1200AclMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.3.1 |
me1200AclMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.815.1.17.3.2 |