LIEBERT-UPSTATION-GXT-UPS-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for LIEBERT-UPSTATION-GXT-UPS-MIB.
118
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
118 total| Object Name |
|---|
emerson OBJECT IDENTIFIER .1.3.6.1.4.1.476 |
RFC1155-SMI Unknown .1.3.6.1.4.1.476 |
liebertCorp OBJECT IDENTIFIER .1.3.6.1.4.1.476.1 |
liebertUps OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1 |
luExtensions OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1 |
luCore OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1 |
lcUpsIdent OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.1 |
lcUpsIdentManufacturerThe UPS manufacturer.ro DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.1 |
lcUpsIdentModelThe UPS Model designation.rw DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.2 |
lcUpsIdentSoftwareVersionThe UPS SNMP Agent software version.ro DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.3 |
lcUpsIdentSpecificA reference to MIB definitions specific to the
particular UPS being managed. This object is
used to locate the product-specific MIB for this
device.
If this information is not present, its value
should be the OBJECT IDENTIFIER { 0 0 },
which is a syntactically valid object identifier,
and any conformant implementation of ASN.1 and BER
must be able to generate and recognize this
value.ro OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.1.4 |
lcUpsIdentFirmwareVersionThe firmware revision level of the UPS.ro DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.5 |
lcUpsIdentSerialNumberThe serial number of the UPS.ro DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.6 |
lcUpsIdentManufactureDateThe date of manufacture of the UPS.ro DisplayString .1.3.6.1.4.1.476.1.1.1.1.1.7 |
lcUpsBattery OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.2 |
lcUpsBatTimeRemainingThe estimated time to depletion of battery charge.
(Unit of measure: Minute)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.2.1 |
lcUpsBatVoltageThe current battery voltage. (Unit of measure:
volt)ro INTEGER (-32768..32767) .1.3.6.1.4.1.476.1.1.1.1.2.3 |
lcUpsBatCapacityThe current battery capacity in percentage of
total available.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.2.6 |
lcUpsInput OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.3 |
lcUpsInputFrequencyThe current input frequency. (Unit of measure:
Hertz)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.3.1 |
lcUpsInputNumLinesThe number of input lines utilized in this
device. This entry indicates the number of rows in
the input table.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.3.5 |
lcUpsInputTable SEQUENCE OF LcUpsInputEntry .1.3.6.1.4.1.476.1.1.1.1.3.6 |
lcUpsInputEntry LcUpsInputEntry .1.3.6.1.4.1.476.1.1.1.1.3.6.1 |
lcUpsInputLineThe input Line.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.3.6.1.1 |
lcUpsInputVoltageThe input voltage. (Unit of measure: Volt)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.3.6.1.2 |
lcUpsOutput OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.4 |
lcUpsOutputFrequencyThe current output frequency. (Unit of measure:
Hertz)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.1 |
lcUpsOutputLoadThe current output load percentage.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.2 |
lcUpsOutputNumLinesThe number of output lines utilized in this
device. This entry indicates the number of rows in
the output table.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.3 |
lcUpsOutputTable SEQUENCE OF LcUpsOutputEntry .1.3.6.1.4.1.476.1.1.1.1.4.4 |
lcUpsOutputEntry LcUpsOutputEntry .1.3.6.1.4.1.476.1.1.1.1.4.4.1 |
lcUpsOutputLineThe output Line.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.4.1.1 |
lcUpsOutputVoltageThe output voltage. (Unit of measure: Volt)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.4.1.2 |
lcUpsOutputCurrentThe output current. (Unit of measure: Amp)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.4.1.3 |
lcUpsOutputWattsThe output power in watts.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.4.5 |
lcUpsInverter OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.5 |
lcUpsInverterStatusThe state of the inverter. Unknown is returned if
the state can not be determined.ro Enumeration .1.3.6.1.4.1.476.1.1.1.1.5.1 |
lcUpsAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6 |
lcUpsAlarmsThe current number of alarm conditions.ro Gauge .1.3.6.1.4.1.476.1.1.1.1.6.1 |
lcUpsAlarmTable SEQUENCE OF LcUpsAlarmEntry .1.3.6.1.4.1.476.1.1.1.1.6.2 |
lcUpsAlarmEntry LcUpsAlarmEntry .1.3.6.1.4.1.476.1.1.1.1.6.2.1 |
lcUpsAlarmIdA unique identifier for an alarm condition. This
value must remain constant between agent
initializations.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.6.2.1.1 |
lcUpsAlarmDescrA reference to an alarm description object. The
object referenced should not be accessible, but
rather be used to provide a unique description of
the alarm condition.ro OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.2.1.2 |
lcUpsAlarmTimeThe value of sysUpTime when the alarm condition
occured.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.476.1.1.1.1.6.2.1.3 |
lcUpsAlarmConditions OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3 |
lcUpsAlarmLowBatteryWarning OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.1 |
lcUpsAlarmLowBatteryShutdown OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.2 |
lcUpsAlarmUtilFailed OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.3 |
lcUpsAlarmOverTempWarning OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.4 |
lcUpsAlarmOverTempShutdown OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.5 |
lcUpsAlarmOutputOverloadWarning OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.6 |
lcUpsAlarmOutputOverloadShutdown OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.7 |
lcUpsAlarmInputOverVoltage OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.8 |
lcUpsAlarmBatteryBad OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.9 |
lcUpsAlarmOnBattery OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.10 |
lcUpsAlarmStopNoticeIssued OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.11 |
lcUpsAlarmUpsOff OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.12 |
lcUpsAlarmInputFreqError OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.13 |
lcUpsAlarmOutputUnderVoltage OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.15 |
lcUpsAlarmOutputOverVoltage OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.16 |
lcUpsBadBypassPower OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.6.3.17 |
lcUpsTest OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.7 |
lcUpsTestBatterySetting this variable to 'start' will initiate
the battery test. Setting this variable to 'abort'
will stop the battery test if the test is in-
progress, otherwise it has no effect. Setting this
variable to 'unknown' has no effect. Reading this
variable will always result in a return value of
'unknown'. If 'lcUpsTestBatteryStatus' is 'failed'
the test may not be performed again and the status
will remain in the failure state.rw Enumeration .1.3.6.1.4.1.476.1.1.1.1.7.1 |
lcUpsTestBatteryStatusThe status of the battery test.ro Enumeration .1.3.6.1.4.1.476.1.1.1.1.7.2 |
lcUpsControl OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.8 |
lcUpsControlOutputOffDelaySetting this object causes the agent to instruct
the UPS to turn off the output after the indicated
number of seconds. The agent counts down the number
of seconds until the event will take place. The
agent issues an lcUpsOutputOffTrap when the countdown
finishes. Note that different models have different
clock resolutions, usually greater than 1 second. As
a result, the command will only be accurate to the
resolution of the UPS's clock.
The command can be cancelled by setting
lcUpsControlCancelCommand to the value cancel.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.1 |
lcUpsControlOutputOnDelaySetting this object causes the agent to instruct
the UPS to turn on the output after the indicated
number of seconds. The agent counts down the number
of seconds until the event will take place. The
agent issues an lcUpsOutputOnTrap when the countdown
finishes. Note that different models have different
clock resolutions, usually greater than 1 second. As
a result, the command will only be accurate to the
resolution of the UPS's clock.
The command can be cancelled by setting
lcUpsControlCancelCommand to the value cancel.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.2 |
lcUpsControlOutputOffTrapDelayWhen 'lcUpsControlOutputOffDelay' reaches a value
less than or equal to this object's value, an
lcUpsOutputOffWarningTrap will be produced and this
object will be reset to 0.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.3 |
lcUpsControlOutputOnTrapDelayWhen 'lcUpsControlOutputOnDelay' reaches a value
less than or equal to this object's value, an
lcUpsOutputOnWarningTrap will be produced and this
object will be reset to 0.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.4 |
lcUpsControlUnixShutdownDelaySetting this object causes the agent to instruct
the UPS to perform a UNIX Shutdown in the indicated
number of seconds. The agent counts down the number
of seconds until the event will take place. A Unix
shutdown is only valid if the UPS is on Battery.
During a UNIX Shutdown, the UPS will turn off the
output even if the Utility comes back on line before
the shutdown time arrives. Note that different models
have different clock resolutions, usually greater
than 1 second. As a result, the command will only
be accurate to the resolution of the UPS's clock.
The command can be cancelled by setting
lcUpsControlCancelCommand to the value 'cancel'.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.5 |
lcUpsControlUnixShutdownTrapDelayWhen 'lcUpsControlUnixShutdownDelay' reaches a value
less than or equal to this object's value, an
lcUpsUnixShutdownWarningTrap will be produced and
this object will be reset to 0.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.6 |
lcUpsControlCancelCommandsSetting this variable to 'cancel' will cause the
agent to issue instructions to the UPS to cancel all
outstanding commands, such as lcUpsControlOutputOff,
lcUpsControlOutputOn, lcUpsControlUnixShutdown.rw Enumeration .1.3.6.1.4.1.476.1.1.1.1.8.7 |
lcUpsControlRebootAgentDelaySetting this object causes the agent to reboot after
the indicated number of seconds have expired. The
value will count down until the event takes place.
The command can be cancelled by setting
lcUpsControlCancleCommand to the value cancel.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.8.8 |
lcUpsNominal OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.9 |
lcUpsNominalOutputVoltageThe nominal output voltage. (Unit of measure:
volt)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.1 |
lcUpsNominalInputVoltageThe nominal input voltage. (Unit of measure:
volt)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.2 |
lcUpsNominalOutputFreqThe nominal output frequency. (Unit of measure:
Hertz)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.5 |
lcUpsNominalInputFreqThe nominal input frequency. (Unit of measure:
Hertz)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.6 |
lcUpsNominalOutputVaRatingThe nominal Volt-Amp rating.rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.7 |
lcUpsNominalOutputWattsRatingThe nominal power rating. (Unit of measure:
watt)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.9.8 |
lcUpsTraps OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.11 |
lcUpsOverloadWarningTrapAn lcUpsOverloadWarningTrap signifies that the UPS
has detected an Overload condition where the output
load has exceeded the UPS's rated capacity. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.1 |
lcUpsOverloadShutdownTrapAn lcUpsOverloadShutdownTrap signifies that the
UPS has detected an Overload condition where the
output load has exceeded the UPS's rated capacity
and has shut off the output. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.2 |
lcUpsOnBatteryTrapAn lcUpsOnBatteryTrap signifies that the
UPS is currently on Battery Power. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.3 |
lcUpsLowBatteryWarningTrapAn lcUpsLowBatteryWarningTrap signifies that the
UPS has entered a Low Battery state. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.4 |
lcUpsLowBatteryShutdownTrapAn lcUpsLowBatteryShutdownTrap signifies that the
UPS has shut off the output due to a Low
Battery state. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.5 |
lcUpsUtilPowerFailedTrapAn lcUpsUtilPowerFailedTrap signifies that the
utility power input to the UPS has been lost. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.6 |
lcUpsUtilPowerRestoredTrapAn lcUpsUtilPowerRestoredTrap signifies that the
utility power has been restored to the UPS. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.7 |
lcUpsInputOverVoltageTrapAn lcUpsInputOverVoltageTrap signifies that the
UPS has detected a high input voltage condition. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.8 |
lcUpsOverTempWarningTrapAn lcUpsOverTempWarningTrap signifies that the
UPS has detected a excessive temperature condition. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.9 |
lcUpsOverTempShutdownTrapAn lcUpsOverTempShutdownTrap signifies that the
UPS has detected a excessive temperature condition
and shut off the output. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.10 |
lcUpsAlarmTrapAn Alarm condition has occurred and is being reported
in the lcUpsAlarmTable. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.11 |
lcUpsOutputOffTrapAn lcUpsOutputOffTrap is sent when the UPS
turns all of its output off, either at the
inverter or via a relay. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.12 |
lcUpsOutputOffWarningTrapAn lcUpsOutputOffWarningTrap is sent when the
lcUpsControlOutputOffDelay reaches the value of
lcUpsControlOutputOffTrapDelay. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.13 |
lcUpsOutputOnTrapAn lcUpsOutputOnTrap is sent when the UPS
turns all of its output back on, either at the
inverter or via a relay. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.14 |
lcUpsOutputOnWarningTrapAn lcUpsOutputOnWarningTrap is sent when the
lcUpsControlOutputOnDelay reaches the value of
lcUpsControlOutputOnTrapDelay. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.15 |
lcUpsUnixShutdownTrapAn lcUpsUnixShutodwnTrap is sent 2 seconds before
the UPS is scheduled to perform a Unix Shutdown. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.16 |
lcUpsUnixShutdownWarningTrapAn lcUpsUnixShutdownWarningTrap is sent when the
lcUpsControlUnixShudownDelay reaches the value of
lcUpsControlUnixShutdownTrapDelay. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.17 |
lcUpsInputFreqErrorTrapAn ldUpsInputFreqErrorTrap signifies that
the UPS has detected that input frequency is outside
tolerable variance. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.22 |
lcUpsOutputOverVoltageTrapAn lcUpsOutputOverVoltageTrap signifies that the
UPS has detected that the output voltage is too high. TRAP-TYPE .1.3.6.1.4.1.476.1.1.1.1.11.0.24 |
lcUpsBypass OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.13 |
lcUpsOnBypassIndicates that the UPS is currently on bypass.ro Enumeration .1.3.6.1.4.1.476.1.1.1.1.13.1 |
lcUpsBypassFrequencyThe current bypass frequency. (Unit of measure:
Hertz)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.13.2 |
lcUpsBypassNumLinesThe number of bypass lines utilized in this
device. This entry indicates the number of rows in
the bypass table.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.13.3 |
lcUpsBypassTable SEQUENCE OF LcUpsBypassEntry .1.3.6.1.4.1.476.1.1.1.1.13.4 |
lcUpsBypassEntry LcUpsBypassEntry .1.3.6.1.4.1.476.1.1.1.1.13.4.1 |
lcUpsBypassLineThe bypass Line.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.13.4.1.1 |
lcUpsBypassVoltageThe bypass voltage. (Unit of measure: Volt)ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.13.4.1.2 |
lcUpsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.1.14 |
lcUpsConfigTypeIndicates the UPS topology.ro Enumeration .1.3.6.1.4.1.476.1.1.1.1.14.1 |
lcUpsConfigBypassInstalledIndicates if a bypass is installed in the UPS.ro Enumeration .1.3.6.1.4.1.476.1.1.1.1.14.2 |
lcUpsConfigModuleCountA number identifying how many multi-module UPS are
connected to the System Control Cabinet.ro INTEGER .1.3.6.1.4.1.476.1.1.1.1.14.3 |
lcUpsConfigAudibleStatusThe requested state of the audible alarm. When in
the disabled state, the audible alarm should never
sound. The enabled state is self-describing. Setting
this object to muted(3) when the audible alarm is
sounding shall temporarily silence the alarm.rw Enumeration .1.3.6.1.4.1.476.1.1.1.1.14.5 |
lcUpsConfigLowBattTimeThe value of lcUpsBatTimeRemaining at which a
lowBatteryWarning condition is declared.
(Unit of measure: Minute)rw INTEGER .1.3.6.1.4.1.476.1.1.1.1.14.6 |
lcUpsConfigAutoRestartSetting this object will start the output after the
indicated number of ticks (1 tick = 10 seconds),
including starting the UPS, if necessary. Setting this
object to 0 will cause the startup to occur immediately.
Setting this object to -1 will disable autorestart.rw INTEGER (-1..32767) .1.3.6.1.4.1.476.1.1.1.1.14.7 |
luUPStationGxt OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.1.14 |
luExperimental OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.2 |
luPrivate OBJECT IDENTIFIER .1.3.6.1.4.1.476.1.1.3 |