Home/Catalog/LIEBERT-GP-FLEXIBLE-CONDITIONS-MIB

LIEBERT-GP-FLEXIBLE-CONDITIONS-MIB

AI MIB Summary

The LIEBERT-GP-FLEXIBLE-CONDITIONS-MIB enables SNMP-based monitoring and management of Liebert GP series power and environmental control units, specifically exposing configurable alarm thresholds and conditional logic states for critical infrastructure parameters. This module facilitates the retrieval of dynamic condition variables and event triggers to automate fault detection and response within data center power distribution and cooling systems.

The MIB module used to register Liebert SNMP OIDs. Copyright 2000-2016 Liebert Corporation. All rights reserved. Reproduction of this document is authorized on the condition that the forgoing copyright notice is included. This Specification is supplied 'AS IS' and Liebert Corporation makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
Main OID:
liebertGlobalProductsFlexibleConditionsModule.1.3.6.1.4.1.476.1.42.1.11.1
727
Objects
Active
Status
3
Dependencies

Imported Objects

SNMPv2-SMI
LIEBERT-GP-REGISTRATION-MIB
LIEBERT-GP-CONDITIONS-MIB

Objects

727 total
Object Name
liebertGlobalProductsFlexibleConditionsModuleThe MIB module used to register Liebert SNMP OIDs. Copyright 2000-2016 Liebert Corporation. All rights reserved. Reproduction of this document is authorized on the condition that the forgoing copyright notice is included. This Specification is supplied 'AS IS' and Liebert Corporation makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY
.1.3.6.1.4.1.476.1.42.1.11.1
lgpFlexConditionsWellKnown
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1
lgpCondId4122SystemInputPowerProblemThe input is not qualified to provide power to the system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4122
lgpCondId4132BypassOverloadPhaseAAn overload exists on output phase A while operating on the bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4132
lgpCondId4133BypassOverloadPhaseBAn overload exists on output phase B while operating on the bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4133
lgpCondId4134BypassOverloadPhaseCAn overload exists on output phase C while operating on the bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4134
lgpCondId4135BypassNotAvailableA problem associated with the bypass has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4135
lgpCondId4137BypassAutoRetransferPrimedAutomatic retransfer from bypass to inverter is possible.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4137
lgpCondId4138BypassAutoRetransferFailedAfter performing a recoverable transfer to bypass, an attempt to auto retransfer from bypass to inverter failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4138
lgpCondId4139BypassExcessAutoRetransfersThe number of auto retransfers, from bypass to inverter, has exceeded the maximum for a specified time interval.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4139
lgpCondId4140BypassRestartInhibitExternalRestart of the bypass is inhibited by the state of an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4140
lgpCondId4141BypassBreakerClosedThe bypass breaker is closed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4141
lgpCondId4142BypassStaticSwitchOverloadBypass off due to static switch overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4142
lgpCondId4143BypassStaticSwitchUnavailableThe static bypass is unavailable to support the critical load.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4143
lgpCondId4144BypassExcessivePulseParallelThe system has performed too many pulse parallel operations within a specified time interval.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4144
lgpCondId4145BypassAutoTransferFailedAn automatic transfer to static bypass failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4145
lgpCondId4146SystemInputPhsRotationErrorThe power conductors on the input line are not wired to the UPS in the sequence preferred for the rectifier (A-B-C).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4146
lgpCondId4147SystemInputCurrentLimitThe RMS input current has reached the input current limit threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4147
lgpCondId4162BatteryLowThe calculated battery time remaining has reached the low battery threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4162
lgpCondId4163OutputOffEndofDischargeOutput turned off due to battery reaching end-of-discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4163
lgpCondId4164BatteryChargingErrorThe battery is not charging properly.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4164
lgpCondId4165BatteryChargingReducedExtrnlUsing a reduced battery charging algorithm due to an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4165
lgpCondId4166BatteryCapacityLowBattery capacity is low.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4166
lgpCondId4167OutputOffOutput is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4167
lgpCondId4168BatteryDischargingThe battery is discharging.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4168
lgpCondId4169BatteryTemperatureImbalanceExcessive temperature differences between battery sensors detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4169
lgpCondId4170BatteryEqualizeThe rectifier output voltage is increased to equalize the battery voltage level.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4170
lgpCondId4171BatteryManualTestInProgressManual battery test is in progress.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4171
lgpCondId4172BatteryAutoTestInProgressAutomatic battery test is in progress.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4172
lgpCondId4173MainBatteryDisconnectOpenMain battery disconnect is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4173
lgpCondId4174BatteryTemperatureSensorFaultA battery temperature sensor fault has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4174
lgpCondId4175BypassFrequencyErrorThe bypass frequency is outside the inverter synchronization limits.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4175
lgpCondId4176BatteryCircuitBreaker1OpenBattery circuit breaker 1 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4176
lgpCondId4177BatteryBreaker1OpenFailureBattery circuit breaker 1 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4177
lgpCondId4178BatteryBreaker1CloseFailureBattery circuit breaker 1 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4178
lgpCondId4179BatteryCircuitBreaker2OpenBattery circuit breaker 2 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4179
lgpCondId4180BatteryBreaker2OpenFailureBattery circuit breaker 2 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4180
lgpCondId4181BatteryBreaker2CloseFailureBattery circuit breaker 2 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4181
lgpCondId4182BatteryCircuitBreaker3OpenBattery circuit breaker 3 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4182
lgpCondId4183BatteryBreaker3OpenFailureBattery circuit breaker 3 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4183
lgpCondId4184BatteryBreaker3CloseFailureBattery circuit breaker 3 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4184
lgpCondId4185BatteryCircuitBreaker4OpenBattery circuit breaker 4 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4185
lgpCondId4186BatteryBreaker4OpenFailureBattery circuit breaker 4 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4186
lgpCondId4187BatteryBreaker4CloseFailureBattery circuit breaker 4 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4187
lgpCondId4188BatteryCircuitBreaker5OpenBattery circuit breaker 5 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4188
lgpCondId4189BatteryBreaker5OpenFailureBattery circuit breaker 5 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4189
lgpCondId4190BatteryBreaker5CloseFailureBattery circuit breaker 5 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4190
lgpCondId4191BatteryCircuitBreaker6OpenBattery circuit breaker 6 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4191
lgpCondId4192BatteryBreaker6OpenFailureBattery circuit breaker 6 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4192
lgpCondId4193BatteryBreaker6CloseFailureBattery circuit breaker 6 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4193
lgpCondId4194BatteryCircuitBreaker7OpenBattery circuit breaker 7 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4194
lgpCondId4195BatteryBreaker7OpenFailureBattery circuit breaker 7 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4195
lgpCondId4196BatteryBreaker7CloseFailureBattery circuit breaker 7 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4196
lgpCondId4197BatteryCircuitBreaker8OpenBattery circuit breaker 8 is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4197
lgpCondId4198BatteryBreaker8OpenFailureBattery circuit breaker 8 failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4198
lgpCondId4199BatteryBreaker8CloseFailureBattery circuit breaker 8 failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4199
lgpCondId4200BatteryChargingInhibitedBattery charging is inhibited due to an external inhibit signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4200
lgpCondId4213SystemShutdownEPOSystem shutdown due to Emergency Power Off (EPO).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4213
lgpCondId4214SystemShutdownREPOSystem shutdown due to Remote Emergency Power Off (REPO).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4214
lgpCondId4215SystemOutputOffThe system output is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4215
lgpCondId4216BypassBackfeedDetectedThe system detected a voltage on the bypass when none was expected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4216
lgpCondId4217BypassManualXfrInhibitedManual transfer from inverter to bypass is inhibited - bypass not qualified.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4217
lgpCondId4218BypassManualRexfrInhibitedManual transfer from bypass to inverter is inhibited - inverter output not qualified.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4218
lgpCondId4219BatteryOverTemperatureA battery temperature sensor is reporting a value above a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4219
lgpCondId4220BatteryExternalMonitor1External battery monitor 1 - battery maintenance required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4220
lgpCondId4221BatteryExternalMonitor2External battery monitor 2 - battery maintenance required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4221
lgpCondId4222BatteryGroundFaultBattery system ground fault amperage exceeds the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4222
lgpCondId4229EmergencyPowerOffLatchedSystem output is off - 'Emergency Power Off (EPO) - latched' requires manual reset.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4229
lgpCondId4230SystemOutputLowPowerFactorThe system output power factor is low, resulting in reduced output capacity.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4230
lgpCondId4231OutputCurrentExceedsThresholdOutput current for one or more phases exceeds a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4231
lgpCondId4233InverterFailureInverter failure - inverter output is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4233
lgpCondId4234InverterOverloadPhaseAInverter is operating with an overload on phase A.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4234
lgpCondId4235InverterOverloadPhaseBInverter is operating with an overload on phase B.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4235
lgpCondId4236InverterOverloadPhaseCInverter is operating with an overload on phase C.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4236
lgpCondId4237InverterInhibitExternalRestart of the inverter is inhibited by an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4237
lgpCondId4238InverterOutBreakerOpenFailInverter output breaker failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4238
lgpCondId4239InverterOutBreakerCloseFailInverter output breaker failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4239
lgpCondId4270InputContact01The external input contact 1.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4270
lgpCondId4271InputContact02The external input contact 2.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4271
lgpCondId4272InputContact03The external input contact 3.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4272
lgpCondId4273InputContact04The external input contact 4.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4273
lgpCondId4274InputContact05The external input contact 5.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4274
lgpCondId4275InputContact06The external input contact 6.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4275
lgpCondId4276InputContact07The external input contact 7.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4276
lgpCondId4277InputContact08The external input contact 8.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4277
lgpCondId4278InputContact09The external input contact 9.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4278
lgpCondId4279InputContact10The external input contact 10.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4279
lgpCondId4280InputContact11The external input contact 11.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4280
lgpCondId4281InputContact12The external input contact 12.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4281
lgpCondId4282InputContact13The external input contact 13.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4282
lgpCondId4283InputContact14The external input contact 14.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4283
lgpCondId4284InputContact15The external input contact 15.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4284
lgpCondId4285InputContact16The external input contact 16.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4285
lgpCondId4286OutputAmpOverUserLimitPhsAThe phase A output has exceeded the user amperage threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4286
lgpCondId4287OutputAmpOverUserLimitPhsBThe phase B output has exceeded the user amperage threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4287
lgpCondId4288OutputAmpOverUserLimitPhsCThe phase C output has exceeded the user amperage threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4288
lgpCondId4289InverterTransferInhibitExtTransfer of critical bus source to inverter is inhibited by an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4289
lgpCondId4290InverterShutdownOverloadThe inverter has shutdown due to a sustained overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4290
lgpCondId4294InletAirOverTemperatureThe inlet air exceeds the maximum temperature threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4294
lgpCondId4295RectifierFailureRectifier failure - rectifier is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4295
lgpCondId4296RectifierOperationInhibitExtThe operation of the rectifier is inhibited by an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4296
lgpCondId4297UPSOutputonInverterThe output power is supplied by the inverter.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4297
lgpCondId4298UPSOutputonBypassThe output power is supplied by the bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4298
lgpCondId4299OutputLoadonMaintBypassThe output power is supplied by the maintenance bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4299
lgpCondId4300InternalCommunicationsFailureThe control has detected a communication failure of a component on the internal communication bus.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4300
lgpCondId4308DCBusGroundFaultPositiveA ground fault has been detected on the positive DC Bus link.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4308
lgpCondId4309DCBusGroundFaultNegativeA ground fault has been detected on the negative DC Bus link.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4309
lgpCondId4310EquipmentOverTemperatureEquipment over temperature summary event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4310
lgpCondId4311SystemFanFailureSystem fan failure - one or more fans have failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4311
lgpCondId4313PasswordChangedPassword changed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4313
lgpCondId4314PowerSupplyFailurePower supply failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4314
lgpCondId4315OnGeneratorA generator is supplying the power to the system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4315
lgpCondId4316AutoRestartInProgressAuto restart is in progress.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4316
lgpCondId4317AutoRestartInhibitedExtAuto restart inhibited due to an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4317
lgpCondId4320InitiatedTransfertoBypassUser initiated manual transfer to bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4320
lgpCondId4321InitiatedTransfertoInverterUser initiated manual transfer to inverter.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4321
lgpCondId4322BatteryTestPassedBattery test passed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4322
lgpCondId4323BatteryTestFailedBattery test failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4323
lgpCondId4324BatteryTestManuallyStoppedThe battery test was manually stopped prior to completion.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4324
lgpCondId4325BackfeedBreakerOpenThe backfeed breaker is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4325
lgpCondId4341VelocityAuthenticationFailureNotification of a message rejected by Velocity due to an authentication failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4341
lgpCondId4360ReceptacleOverCurrentThe system has detected a receptacle over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4360
lgpCondId4361ReceptacleUnderCurrentThe system has detected a receptacle under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4361
lgpCondId4382SystemInputCurrentImbalanceSystem Input Currents are Imbalanced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4382
lgpCondId4383BypassStaticSwitchOffExtrnlBypass static switch is off due to the state of an external signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4383
lgpCondId4384BatteryEoDDisconnectBattery disconnect due to end-of-discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4384
lgpCondId4389SystemOutputFaultA fault has been detected in the system output.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4389
lgpCondId4390InverterOffExternalInverter is off (operation is inhibited) due to external signal state.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4390
lgpCondId4391InverterStaticSwitchSCRShortThe system has detected a short across one or more inverter static switch Silicon Controlled Rectifiers (SCR).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4391
lgpCondId4392TemperatureSensorErrorOne or more temperature sensors cannot provide a valid temperature reading (i.e. sensor failure, wiring failure, sense circuit failure, etc).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4392
lgpCondId4406BranchOverCurrentThe system has detected a module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4406
lgpCondId4407BranchUnderCurrentThe system has detected a module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4407
lgpCondId4416BranchOverCurrentThe system has detected a module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4416
lgpCondId4417BranchUnderCurrentThe system has detected a module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4417
lgpCondId4421BranchFailureOne or more conditions indicate a Branch Receptacle Module failure , service is required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4421
lgpCondId4436PDUOverCurrentThe system has detected a module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4436
lgpCondId4437PDUUnderCurrentThe system has detected a module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4437
lgpCondId4438SystemInternalTemperatureRiseExcessive temperature rise internal to the system (i.e. difference between the output versus input temperature is too large).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4438
lgpCondId4439AutomaticRestartFailedAutomatic restart failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4439
lgpCondId4440FuseFailureA summary event indicating one or more fuse failures.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4440
lgpCondId4441SystemControllerErrorSystem controller internal error.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4441
lgpCondId4442SystemBreakersOpenFailureOne or more breakers in the system failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4442
lgpCondId4448PDUOverCurrentThe system has detected a module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4448
lgpCondId4449PDUUnderCurrentThe system has detected a module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4449
lgpCondId4468PDUOverCurrentL1The system has detected a module over current condition on line 1.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4468
lgpCondId4469PDUOverCurrentL2The system has detected a module over current condition on line 2.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4469
lgpCondId4470PDUOverCurrentL3The system has detected a module over current condition on line 3.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4470
lgpCondId4471PDUUnderCurrentL1The system has detected a module under current condition on line 1.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4471
lgpCondId4472PDUUnderCurrentL2The system has detected a module under current condition on line 2.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4472
lgpCondId4473PDUUnderCurrentL3The system has detected a module under current condition on line 3.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4473
lgpCondId4492ReceptaclePowerStateOnThe receptacle power state changed to the ON state.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4492
lgpCondId4493ReceptaclePowerStateOffThe receptacle power state changed to the OFF state.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4493
lgpCondId4494BranchBreakerOpenThe Branch Receptacle Module's input breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4494
lgpCondId4495DeviceConfigurationChangeDevice Configuration Change.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4495
lgpCondId4496BasicDisplayModuleRemovedBasic Display Module Removed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4496
lgpCondId4497BasicDisplayModuleDiscoveredBasic Display Module Discovered.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4497
lgpCondId4500PDUOverCurrentThe system has detected a power module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4500
lgpCondId4501PDUUnderCurrentThe system has detected a power module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4501
lgpCondId4502PDUFailureOne or more conditions indicate a power module failure, service is required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4502
lgpCondId4503PDUCommunicationFailInternal communications failure with the Power Module.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4503
lgpCondId4504BranchRemovedBranch Receptacle Module Removed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4504
lgpCondId4505BranchDiscoveredBranch Receptacle Module Discovered.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4505
lgpCondId4506BranchOverCurrentThe system has detected a Branch Receptacle Module over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4506
lgpCondId4507BranchCurrentThe system has detected a Branch Receptacle Module under current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4507
lgpCondId4508ReceptacleLoadRemovedThe receptacle's load stopped drawing power.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4508
lgpCondId4509ReceptacleLoadAddedThe receptacle's load started to draw power.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4509
lgpCondId4523ModuleRemovedModule Removed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4523
lgpCondId4524ModuleAddedModule Added.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4524
lgpCondId4550FirmwareUpdateRequiredModule compatibility error requires a system firmware update to resolve.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4550
lgpCondId4551GenericTestEventA generic test event designed to evaluate system handling of events.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4551
lgpCondId4580OverTemperatureAn over temperature condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4580
lgpCondId4581UnderTemperatureAn under temperature condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4581
lgpCondId4588OverRelativeHumidityAn over relative humidity condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4588
lgpCondId4589UnderRelativeHumidityAn under relative humidity condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4589
lgpCondId4601ExternalAirSensorAOverTemperature[Ext Air Sensor A Temperature] has exceeded [External Air Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4601
lgpCondId4604ExternalAirSensorBOverTemperature[Ext Air Sensor B Temperature] has exceeded [External Air Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4604
lgpCondId4608ExtAirSensorAUnderTemperature[Ext Air Sensor A Temperature] has dropped below [Ext Air Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4608
lgpCondId4611ExtAirSensorBUnderTemperature[Ext Air Sensor B Temperature] has dropped below [Ext Air Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4611
lgpCondId4615ExtDewPointOverTemperatureAt least one dew point temperature reading ([Ext Air Sensor A Dew Point Temp], [Ext Air Sensor B Dew Point Temp]...) has exceeded [Ext Dew Point Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4615
lgpCondId4618ExternalAirSensorAIssueThe external air sensor A is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4618
lgpCondId4621ExternalAirSensorBIssueThe external air sensor B is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4621
lgpCondId4626SupplyChilledWaterOverTemp[Supply Fluid Temperature] has exceeded [High Supply Fluid Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4626
lgpCondId4629SupplyChilledWaterTempSensorIssueThe supply chilled water temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4629
lgpCondId4634SupplyRefrigerantOverTempEvent that is activated when [Supply Refrigerant Temperature] exceeds [Supply Refrig Over Temp Threshold]. The event is deactivated when the temperature drops below the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4634
lgpCondId4637SupplyRefrigerantUnderTemp[Supply Refrigerant Temperature] has dropped below a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4637
lgpCondId4640SupplyRefrigerantTempSensorIssueThe supply refrigeramt temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4640
lgpCondId4645SupplyFluidOverTemp[Supply Fluid Temperature] has exceeded [Supply Fluid Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4645
lgpCondId4648SupplyFluidUnderTemp[Supply Fluid Temperature] has dropped below a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4648
lgpCondId4651SupplyFluidTempSensorIssueThe supply fluid temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4651
lgpCondId4656Pump1LossofFlowLoss of flow is detected in pump 1. The loss of flow condition occurs when no differential pressure is detected across the pump.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4656
lgpCondId4659Pump2LossofFlowLoss of flow is detected in pump 2. The loss of flow condition occurs when no differential pressure is detected across the pump.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4659
lgpCondId4662PumpShortCyclePumps have short cycled. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4662
lgpCondId4669Compressor1AHighHeadPressureCompressor 1A high head pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4669
lgpCondId4672Compressor1BHighHeadPressureCompressor 1B high head pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4672
lgpCondId4675Compressor2AHighHeadPressureCompressor 2A high head pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4675
lgpCondId4678Compressor2BHighHeadPressureCompressor 2B high head pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4678
lgpCondId4681Compressor1AShortCycleCompressor 1A short cycle. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4681
lgpCondId4684Compressor1BShortCycleCompressor 1B short cycle. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4684
lgpCondId4687Compressor2AShortCycleCompressor 2A short cycle. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4687
lgpCondId4690Compressor2BShortCycleCompressor 2B short cycle. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4690
lgpCondId4693Tandem1LowSuctionPressure'Tandem compressors' 1 low suction pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4693
lgpCondId4696Tandem2LowSuctionPressure'Tandem compressors' 2 low suction pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4696
lgpCondId4703ChilledWaterControlValvePositionChilled water valve out of position. Chilled water control valve position does not match expected value.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4703
lgpCondId4711SystemCondensationDetectedSystem condensation detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4711
lgpCondId4714ShutdownLossOfPowerSystem lost power. This event becomes active when the unit is powered on following an unexpected loss of power.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4714
lgpCondId4720SmokeDetectedSmoke detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4720
lgpCondId4723WaterUnderFloorWater under the floor is detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4723
lgpCondId4726ServiceRequiredUnit requires servicing.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4726
lgpCondId4729FanIssueOne or more fans are not operating within their operational parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4729
lgpCondId4732ReceptacleLoadDroppedThe receptacle's load is not drawing power.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4732
lgpCondId4740BatteryAutomaticTestInhibitedAutomatic (scheduled) battery tests are inhibited.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4740
lgpCondId4741BatterySelfTestBattery self test is in progress.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4741
lgpCondId4742BatteryLowShutdownBattery disconnect due to end-of-discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4742
lgpCondId4747EquipmentTemperatureSensorFailOne or more temperature sensors report a temperature outside of the range of expected operation.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4747
lgpCondId4749SystemFanFailureRedundantRedundant system fan failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4749
lgpCondId4750MultipleFanFailureMultiple fan failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4750
lgpCondId4753MainControllerFaultA Main Controller fault has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4753
lgpCondId4754SystemBreakersCloseFailureOne or more breakers in the system failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4754
lgpCondId4755InputFilterCycleLockThe input filter disconnect is open due to exceeding the maximum number of cycles.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4755
lgpCondId4756ServiceCodeActiveService code is running.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4756
lgpCondId4757LBSActiveThe Load Bus Sync option is active.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4757
lgpCondId4758LBSInhibitedThe system has detected that conditions to perform Load Bus Sync are not satisfied.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4758
lgpCondId4759LeadingPowerFactorThe leading output Power Factor has fallen below a specified value.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4759
lgpCondId4760ControlsResetRequiredA controls reset is required due to one or more critical settings changing.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4760
lgpCondId4823ParallelCommWarningParallel communication bus warning.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4823
lgpCondId4824SystemCommFailFailure of a device on the multi-module system communication bus.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4824
lgpCondId4825LossofRedundancyThe multi-module collection doesn't have enough modules to satisfy the redundancy configuration.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4825
lgpCondId4826BPSSStartupInhibitThe Bypass Static Switch startup is inhibited.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4826
lgpCondId4827MMSTransferInhibitThe critical load can not be manually transferred from inverter to bypass.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4827
lgpCondId4828MMSRetransferInhibitThe critical load can not be manually retransferred from bypass to inverter.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4828
lgpCondId4830MMSLossofSyncPulseMulti-module system loss of sync pulse.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4830
lgpCondId4831MMSOverloadMulti-module system overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4831
lgpCondId4834MMSOnBatteryThe multi-module system is on battery.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4834
lgpCondId4835MMSLowBatteryWarningMulti-module system low battery warning.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4835
lgpCondId4906LowAmbientTemperatureThe system has detected a low ambient temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4906
lgpCondId4907HighAmbientTemperatureThe system has detected a high ambient temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4907
lgpCondId4908LowOverallVoltageThe system has detected a low battery string overall voltage condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4908
lgpCondId4909HighOverallVoltageThe system has detected a high battery string overall voltage condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4909
lgpCondId4910HighBatteryStringCurrentThe system has detected a high battery string current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4910
lgpCondId4911LowBatteryStringFloatCurrentThe system has detected a low battery string float current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4911
lgpCondId4912HighBatteryStringFloatCurrentThe system has detected a high battery string float current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4912
lgpCondId4913HighBatteryStringRippleCurrentThe system has detected a high battery string ripple current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4913
lgpCondId4914BatteryStringDischargeDetectedThe system has detected a battery string discharge condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4914
lgpCondId4915MaximumDischargeTimeExceededThe system has detected an excessive discharge time condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4915
lgpCondId4916DischargeLowOverallVoltageThe system has detected a low battery string overall voltage condition during a discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4916
lgpCondId4917DischargeLowCellVoltageThe system has detected a low cell voltage condition during a discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4917
lgpCondId4918DischargeHighBatteryStringCurrentThe system has detected a high battery string current condition during a discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4918
lgpCondId4919ExcessiveCelltoCellTemperatureDeviationThe system has detected an excessive cell to cell temperature deviation condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4919
lgpCondId4920ExcessiveCelltoAmbientTemperatureDeviationThe system has detected an excessive cell to ambient temperature deviation condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4920
lgpCondId4964LowCellVoltageThe system has detected a low cell voltage condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4964
lgpCondId4965HighCellVoltageThe system has detected a high cell voltage condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4965
lgpCondId4966LowCellTemperatureThe system has detected a low cell temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4966
lgpCondId4967HighCellTemperatureThe system has detected a high cell temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4967
lgpCondId4968LowInternalResistanceThe system has detected a low internal resistance condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4968
lgpCondId4969HighInternalResistanceThe system has detected a high internal resistance condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4969
lgpCondId4970HighIntercellResistanceThe system has detected a high intercell resistance condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4970
lgpCondId4978IntertierResistanceHighThe system has detected a high intertier resistance condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4978
lgpCondId4980SupplyChilledWaterLossofFlowSupply chilled water or glycol flow is too low.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4980
lgpCondId4983SupplyRefrigOverTempBand1[Supply Refrigerant Temperature] is above the upper threshold specified by [Supply Refrig Temp Band 1].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4983
lgpCondId4986SupplyRefrigUnderTempBand1[Supply Refrigerant Temperature] is below the lower threshold specified by [Supply Refrig Temp Band 1].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4986
lgpCondId4990SupplyRefrigOverTempBand2[Supply Refrigerant Temperature] is above the upper threshold specified by [Supply Refrig Temp Band 2].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4990
lgpCondId4993SupplyRefrigUnderTempBand2[Supply Refrigerant Temperature] is below the lower threshold specified by [Supply Refrig Temp Band 2].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4993
lgpCondId4996Inverter1ShortCycleInverter for pump 1 has short cycled and is temporarily locked out from further operation to protect from thermal overload. A short cycle is defined as powering on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4996
lgpCondId4999Inverter2ShortCycleInverter for pump 2 has short cycled and is temporarily locked out from further operation to protect from thermal overload. A short cycle is defined as powering on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.4999
lgpCondId5015SupplyAirOverTemperature[Supply Air Temperature] has exceeded [High Supply Air Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5015
lgpCondId5019SupplyAirUnderTemperature[Supply Air Temperature] has dropped below [Low Supply Air Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5019
lgpCondId5023ReturnAirOverTemperature[Return Air Temperature] has exceeded [High Return Air Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5023
lgpCondId5026SupplyAirSensorIssueThe air sensor at the outlet of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5026
lgpCondId5034HighReturnHumidity[Return Humidity] has exceeded [High Return Humidity Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5034
lgpCondId5036LowReturnHumidity[Return Humidity] has dropped below [Low Return Humidity Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5036
lgpCondId5037HumidifierHoursExceededOperating hours for the humidifier have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5037
lgpCondId5038DehumidifierHoursExceededOperating hours for the dehumidifier have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5038
lgpCondId5039HumidifierUnderCurrentThe electrical current to the humidifier has dropped below its lower threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5039
lgpCondId5040HumidifierOverCurrentThe electrical current to the humidifier has exceeded its upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5040
lgpCondId5041HumidifierLowWaterThe water level in the humidifier has dropped below its threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5041
lgpCondId5042HumidifierCylinderWornHumidifier cylinder is not operating properly and needs to be replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5042
lgpCondId5043HumidifierIssueHumidifier issue detected, causing it to be locked out.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5043
lgpCondId5044ExtHumidifierLockoutThe humidifier is shut down and disabled by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5044
lgpCondId5045HumidifierControlBoardNotDetectedHumidifier control board is required to be connected, but no signal is detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5045
lgpCondId5046ReturnHumidityOutOfProportionalBand[Return Humidity] has exceeded the upper limit of [Dehumidification Proportional Band], or has dropped below the lower limit of [Humidification Proportional Band] ], for an extended period of time.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5046
lgpCondId5053LossofAirFlowNo air flow through the unit due to failure of all fans.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5053
lgpCondId5054FanHoursExceededOperating hours for the unit blower fan have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5054
lgpCondId5055TopFanIssueThe top fan is not operating within its normal parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5055
lgpCondId5056BottomFanIssueThe bottom fan is not operating within its normal parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5056
lgpCondId5060RemoteSensorIssueRemote sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5060
lgpCondId5062Compressor1LowSuctionPressureCompressor 1 low suction pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5062
lgpCondId5063Compressor1HoursExceededOperating hours for compressor 1 have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5063
lgpCondId5064DigScrollComp1TempSensorIssueDigital scroll compressor 1 temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5064
lgpCondId5065DigScrollComp1OverTempDigital scroll compressor 1 shut off because its head temperature has exceeded the upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5065
lgpCondId5066Compressor1LowPressureTransducerIssueCompressor 1 low pressure transducer is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5066
lgpCondId5067ExtCompressorLockoutThe compressor is shut down and disabled by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5067
lgpCondId5068ReheaterOverTemperatureThe temperature of the reheater has exceeded its threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5068
lgpCondId5069ElectricReheater1HoursExceededOperating hours for electric reheater 1 have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5069
lgpCondId5070ExtReheatLockoutThe reheater is shut down and disabled by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5070
lgpCondId5071Condenser1IssueCondenser 1 is not operating within its normal parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5071
lgpCondId5072CondenserVFDIssueThe condenser fan Variable Frequency Drive is offline.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5072
lgpCondId5073CondenserTVSSIssueThe condenser Transient Voltage Surge Suppressor or Surge Protection Device has failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5073
lgpCondId5104ExtOverTemperatureA temperature has exceeded its threshold, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5104
lgpCondId5105ExtLossofFlowLoss of flow is detected, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5105
lgpCondId5106ExtCondenserPumpHighWaterHigh water is detected in the condensate pump by the auxiliary float, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5106
lgpCondId5107ExtStandbyGlycolPumpOnThe standby glycol pump is on, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5107
lgpCondId5108ExternalFireDetectedFire detected, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5108
lgpCondId5109UnitOnUnit was turned on.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5109
lgpCondId5110UnitOffUnit was turned off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5110
lgpCondId5111UnitStandbyUnit was placed in standby mode.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5111
lgpCondId5112UnitPartialShutdownAn event has occurred requiring some system components to be shutdown and disabled.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5112
lgpCondId5113UnitShutdownAn event has occurred requiring the unit to be shutdown and disabled to prevent damage to the system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5113
lgpCondId5114WaterLeakageDetectorSensorIssueThe water leakage detector sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5114
lgpCondId5115BMSCommunicationsTimeoutBuilding Management System (or external monitoring system) has not communicated with the system within the expected timeframe.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5115
lgpCondId5116MaintenanceDueThe calculated maintenance date has been reached.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5116
lgpCondId5117MaintenanceCompletedMaintenance has been completed on the unit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5117
lgpCondId5118CloggedAirFilterAir filter is dirty and needs to be (cleaned or) replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5118
lgpCondId5119RAMBatteryIssueRAM or RAM backup battery is not operating correctly.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5119
lgpCondId5120MasterUnitCommunicationLostCommunication with master unit has been lost.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5120
lgpCondId5121HighPowerShutdownSupply to high power components has been shutdown.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5121
lgpCondId5126DigScrollComp2OverTempDigital scroll compressor 2 shut off because its head temperature has exceeded the upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5126
lgpCondId5144OutputOfUfThe output frequency has exceeded a specified range for a specified period of time.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5144
lgpCondId5145MMSModuleAlarmActiveActive alarm or fault of any module in a multi-module system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5145
lgpCondId5146CompressorPumpDownIssueUnable to pump down suction-side pressure during compressor shutdown.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5146
lgpCondId5147ReturnAirSensorIssueThe air sensor at the inlet of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5147
lgpCondId5148CompressorHighPressureTransducerIssueCompressor high pressure transducer is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5148
lgpCondId5149BatteryNotQualifiedThe UPS battery voltage is not qualified. This event will be detected even in the absence of battery disconnect or when it is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5149
lgpCondId5150BatteryTerminalsReversedThe measured battery voltage is a negative value due to reverse battery terminal connections.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5150
lgpCondId5151BatteryConverterFailureBattery converter failure. This is a summary event caused by one or more power sub-modules in a UPS module.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5151
lgpCondId5152InverterSCROpenThe system has detected an open across one or more inverter static switch Silicon Controlled Rectifiers.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5152
lgpCondId5153LoadSharingFaultDifference between any phase inverter current of unit and the relevant average output current of parallel system is more than a specific percent of nominal current.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5153
lgpCondId5154DCBusAbnormalThe system has detected an abnormal DC Bus Voltage.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5154
lgpCondId5155MainsInputNeutralLostLoss of neutral in the input source is detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5155
lgpCondId5156LoadImpactTransferOn bypass as result of load impact.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5156
lgpCondId5157UserOperationInvalidUser attempted an invalid operation.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5157
lgpCondId5158PowerSubModuleFaultOne or more failures detected in power module, inverter or rectifier.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5158
lgpCondId5178OutputOvervoltageOne or more of the output phase voltages has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5178
lgpCondId5179OutputUndervoltageOne or more of the output phase voltages has dropped below the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5179
lgpCondId5180OutputOvercurrentOne or more of the phase currents has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5180
lgpCondId5181NeutralOvercurrentThe system's neutral current has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5181
lgpCondId5182GroundOvercurrentSystem ground current has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5182
lgpCondId5183OutputVoltageTHDThe Total Harmonic Distortion of the voltage on one or more of the output phases has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5183
lgpCondId5184OutputFrequencyErrorThe output frequency is outside a specified range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5184
lgpCondId5185TransformerOvertemperatureIndicates a unit transformer overtemperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5185
lgpCondId5212PanelSummaryStatusThe status for the panel. Detects and annunciates upon occurrence of any branch or panelboard main breaker active event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5212
lgpCondId5213PanelOvervoltageOne or more of the phase voltages of this panel has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5213
lgpCondId5214PanelUndervoltageOne or more of the phase voltages of this panel is less than the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5214
lgpCondId5215PanelOvercurrentOne or more of the phase currents of this panel has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5215
lgpCondId5216PanelNeutralOvercurrentThe Neutral current of this panel has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5216
lgpCondId5217PanelGroundOvercurrentThe Ground current of this panel has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5217
lgpCondId5226BranchOvercurrentThe current in one or more phases of this branch exceeds the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5226
lgpCondId5227BranchUndercurrentThe current in one or more phases of this branch is less than the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5227
lgpCondId5245SubfeedPhaseOvercurrentOne or more of the phase currents in this subfeed has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5245
lgpCondId5246SubfeedNeutralOvercurrentThe Neutral current in this subfeed has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5246
lgpCondId5247SubfeedGroundOvercurrentThe Ground current of this subfeed has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5247
lgpCondId5249EventStateThe present state of this digital event input.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5249
lgpCondId5263CompressorNotStoppingCompressor commanded to stop, but continues to run.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5263
lgpCondId5269CompressorHoursExceeded[Compressor Hours] has exceeded [Compressor Hours Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5269
lgpCondId5270CompressorHighHeadPressureCompressor is shut down due to high head pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5270
lgpCondId5271CompressorLowSuctionPressureCompressor is shut down due to low suction pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5271
lgpCondId5272CompressorThermalOverloadCompressor is shut down due to thermal overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5272
lgpCondId5273CompressorLowOilPressureCompressor low oil pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5273
lgpCondId5274CompressorHeadPressureOverThresholdCompressor head pressure has exceeded an upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5274
lgpCondId5275CompressorLossofDifferentialPressureCompressor is shut down due to low differential pressure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5275
lgpCondId5277CondenserFanIssueCondenser fan is not operating within its operational parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5277
lgpCondId5278LowCondenserRefrigerantPressureRefrigerant pressure in condenser coil is too low.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5278
lgpCondId5280LowFluidPressure[Fluid Pressure] has dropped below a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5280
lgpCondId5293ReturnFluidOverTemp[Return Fluid Temperature] has exceeded a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5293
lgpCondId5294ReturnFluidUnderTemp[Return Fluid Temperature] has dropped below a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5294
lgpCondId5295ReturnFluidTempSensorIssueThe return fluid temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5295
lgpCondId5296TeamworkReturnFluidTempSensorIssueThe return fluid temperature sensors for all Teamwork units are disconnected or the signals are out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5296
lgpCondId5297AllPumpsLossofFlowSystem is shut down due to loss of flow in all available pumps.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5297
lgpCondId5300PumpHoursExceeded[Pump Hours] has exceeded [Pump Hours Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5300
lgpCondId5306FreeCoolingValveHoursExceeded[Free Cooling Valve Hours] has exceeded [Free Cooling Valve Hours Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5306
lgpCondId5308EvaporatorInletTempSensorIssueThe evaporator inlet temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5308
lgpCondId5309TeamworkEvaporatorInletTempSensorIssueThe evaporator inlet temperature sensors for all Teamwork units are disconnected or the signals are out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5309
lgpCondId5310EvaporatorFluidFreezeAutoResetEvaporator outlet fluid temperature has dropped below the freeze threshold. Evaporator has been shut down, but will restart when the temperature rises above the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5310
lgpCondId5311EvaporatorFluidFreezeManualResetRequiredEvaporator outlet fluid temperature has dropped below the freeze threshold. Evaporator has been shut down and requires a manual reset.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5311
lgpCondId5315SubgroupEventOccurredDuringCommunicationLossWhile subgroup unit communication was lost, an event occurred on the subgroup unit. Please check subgroup unit event log.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5315
lgpCondId5335ReturnAirUnderTemperature[Return Air Temperature] has dropped below [Low Return Air Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5335
lgpCondId5349ExtAirSensorAHighHumidity[Ext Air Sensor A Humidity] has exceeded [Ext Air Sensor A High Humidity Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5349
lgpCondId5351ExtAirSensorALowHumidity[Ext Air Sensor A Humidity] has dropped below [Ext Air Sensor A Low Humidity Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5351
lgpCondId5352CompressorShortCycleCompressor short cycle. A short cycle is defined as turning on and off a number of times over a set time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5352
lgpCondId5354DigScrollCompDischargeTempSensorIssueDigital scroll compressor discharge temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5354
lgpCondId5355DigScrollCompOverTempDigital scroll compressor is shut down due to head temperature exceeding an upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5355
lgpCondId5361ExtFreeCoolingLockoutFree cooling is disabled by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5361
lgpCondId5362FreeCoolingTempSensorIssueThe free cooling fluid temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5362
lgpCondId5365HotWaterHotGasValveHoursExceeded[Hot Water / Hot Gas Valve Hours] has exceeded [Hot Water / Hot Gas Valve Hours Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5365
lgpCondId5368ElectricReheaterHoursExceeded[Electric Reheater Hours] has exceeded [Electric Reheaters Hours Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5368
lgpCondId5376MainFanOverloadMain fan is shut down due to thermal overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5376
lgpCondId5377CondenserCondenser is not operating within its operational parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5377
lgpCondId5415ExtLossofAirBlowerLoss of air blower is detected, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5415
lgpCondId5416ExtStandbyUnitOnStandby unit is on, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5416
lgpCondId5417DigitalOutputBoardNotDetectedDigital output board is required to be connected, but no signal is detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5417
lgpCondId5418UnitCodeMissingUnit code has not been entered and saved.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5418
lgpCondId5419UnitCommunicationLostMaster has lost communication with one or more networked units.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5419
lgpCondId5422OvertemperaturePowerOffPower turned off because equipment over temperature limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5422
lgpCondId5423TooManySensorsThe number of sensors connected to the PDU exceeds the allowable limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5423
lgpCondId5432TransformerOvertemperaturePowerOffOutput power shutdown due to high transformer temperature.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5432
lgpCondId5433TransformerOvertemperatureTransformer temperature has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5433
lgpCondId5434TransformerTemperatureSensorFailTransformer temperature sensor has failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5434
lgpCondId5436LowAmbientTemperatureProbeTwoThe system has detected a low ambient temperature condition on temperature probe 2.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5436
lgpCondId5437HighAmbientTemperatureProbeTwoThe system has detected a high ambient temperature condition on temperature probe 2.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5437
lgpCondId5438ThermalRunawayDetectedThe system has detected a thermal runaway condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5438
lgpCondId5439BatteryStringEqualizeThe system has detected a battery string equalize condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5439
lgpCondId5440BatteryStringOfflineThe system has detected the battery string is offline.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5440
lgpCondId5442DischargeLowCellVoltageThe system has detected a low cell voltage condition during a discharge.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5442
lgpCondId5447MMSPowerSharingA module is not sharing power with the other modules in a multi -module system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5447
lgpCondId5453ModuleInStandbyIntelligentParallelingModule is placed into standby operation per Intelligent Paralleling.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5453
lgpCondId5456ECOModeActiveConditions for Activation or Automatic Reactivation have been satisfied.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5456
lgpCondId5457ECOModeSuspendedECO Mode session is suspended.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5457
lgpCondId5458ExcessECOSuspendsNumber of automatic suspensions has exceeded the ECO Mode - Maximum Auto Suspensions setting.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5458
lgpCondId5471DoorOpenAn open door was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5471
lgpCondId5472DoorSensorDisconnectedDoor sensor disconnect detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5472
lgpCondId5479ContactClosureOpenAn open circuit was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5479
lgpCondId5480ContactClosureClosedA closed circuit was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5480
lgpCondId5492ExtSystemCondensationDetectedExternal system condensation detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5492
lgpCondId5495ExtFanIssueOne or more fans are not operating within their operational parameters.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5495
lgpCondId5500ExtRemoteShutdownUnit is shut down by a remote signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5500
lgpCondId5505HotAisleTempOutofRangeThe air temperature in the Hot aisle is either above [Hot Aisle Over Temp Threshold] or below [Hot Aisle Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5505
lgpCondId5508ColdAisleTempOutofRangeThe air temperature in the cold aisle is either above [Cold Aisle Over Temp Threshold] or below [Cold Aisle Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5508
lgpCondId5512RemoteShutdownUnit is shut down by a remote signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5512
lgpCondId5513CompressorCapacityReducedCompressor capacity has been reduced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5513
lgpCondId5514CompressorLowPressureTransducerIssueCompressor low pressure transducer is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5514
lgpCondId5524PDUNeutralOverCurrentThe system has detected a neutral over current condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5524
lgpCondId5531CondenserCommunicationLostCommunication with condenser unit has been lost.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5531
lgpCondId5535CondenserOutsideAirTempSensorIssueCondenser outside air temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5535
lgpCondId5536CondenserOutsideAirTempOutofOperatingRange[Condenser Outside Air Temperature] is either above an upper threshold or below a lower threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5536
lgpCondId5537CondenserControlBoardIssueThe condenser control board is reporting an issue.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5537
lgpCondId5539CondenserRefrigerantPressureOverThresholdCondenser refrigerant pressure has exceeded a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5539
lgpCondId5540CondenserRefrigerantPressureUnderThresholdCondenser refrigerant pressure has dropped below a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5540
lgpCondId5541CondenserRefrigerantPressureSensorIssueCondenser refrigerant pressure sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5541
lgpCondId5542CondenserSupplyRefrigerantOverTempCondenser supply refrigerant temperature has exceeded a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5542
lgpCondId5543CondenserSupplyRefrigerantUnderTempCondenser supply refrigerant temperature has dropped below a specified threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5543
lgpCondId5544CondenserSupplyRefrigerantTempSensorIssueCondenser supply refrigerant temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5544
lgpCondId5545CondenserMaxFanSpeedOverrideFan speed exceeding the maximum set point in order to alleviate a high temperature or pressure condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5545
lgpCondId5559EvaporatorReturnFluidOverTemp[Evaporator Return Fluid Temperature] has exceeded a threshold. The event is deactivated when the temperature drops below the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5559
lgpCondId5560EvaporatorReturnFluidUnderTemp[Evaporator Return Fluid Temperature] has dropped below a threshold. The event is deactivated when the temperature rises above the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5560
lgpCondId5561LBSActiveMasterThis UPS system has been selected as the functional Master Load Bus Synchronization (LBS) system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5561
lgpCondId5562LBSActiveSlaveThis UPS system is synchronized to the output bus of the UPS system that has been selected as the Master Load Bus Synchronization (LBS) system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5562
lgpCondId5563DCBusLowFaultThe DC Bus voltage has reached a critical low level.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5563
lgpCondId5564FanContactorOpenThe fan contactor is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5564
lgpCondId5565FanContactorOpenFailThe fan contactor failed to open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5565
lgpCondId5566FanContactorCloseFailThe fan contactor failed to close.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5566
lgpCondId5567IPInhibitThe intelligent paralleling operation is inhibited.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5567
lgpCondId5568InputUndervoltageOne or more of the input phase voltages has dropped below the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5568
lgpCondId5569InputOvervoltageOne or more of the input phase voltages has exceeded the limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5569
lgpCondId5573AmbientAirSensorIssueAmbient air sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5573
lgpCondId5577ExtDewPointUnderTemperatureAt least one dew point temperature reading ([Ext Air Sensor A Dew Point Temp], [Ext Air Sensor B Dew Point Temp]...) has dropped below [Ext Dew Point Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5577
lgpCondId5578DewPointOverTemperatureDew point temperature reading has exceeded the upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5578
lgpCondId5579DewPointUnderTemperatureDew point temperature reading has dropped below the lower threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5579
lgpCondId5588UnspecifiedGeneralEventOne or more unspecified events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5588
lgpCondId5593RemoteSensorAverageOverTemperature[Remote Sensor Average Temperature] has exceeded [Remote Sensor Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5593
lgpCondId5594RemoteSensorAverageUnderTemperature[Remote Sensor Average Temperature] has dropped below [Remote Sensor Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5594
lgpCondId5595RemoteSensorSystemAverageOverTemperature[Remote Sensor System Average Temperature] has exceeded [Remote Sensor Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5595
lgpCondId5596RemoteSensorSystemAverageUnderTemperature[Remote Sensor System Average Temperature] has dropped below [Remote Sensor Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5596
lgpCondId5597RemoteSensorOverTemperature[Remote Sensor Temperature] has exceeded [Remote Sensor Over Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5597
lgpCondId5598RemoteSensorUnderTemperature[Remote Sensor Temperature] has dropped below [Remote Sensor Under Temp Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5598
lgpCondId5600AirEconomizerEmergencyOverrideIndoor room temperature has exceeded its upper threshold and the outdoor air damper has been opened for emergency cooling.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5600
lgpCondId5601AirEconomizerReducedAirflowAir economizer filter is dirty and needs to be cleaned or replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5601
lgpCondId5604CompressorSuperheatOverThresholdCompressor discharge refrigerant superheat temperature has exceeded an upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5604
lgpCondId5609ThermalRunawayCelltoAmbientTemperatureEventThe delta temperature between a cell temperature and the ambient temperature has exceeded the thermal runaway cell to ambient temperature threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5609
lgpCondId5610ThermalRunawayCelltoCellTemperatureEventThe delta temperature between two cells has exceeded the thermal runaway cell to cell temperature threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5610
lgpCondId5611ThermalRunawayChargerCurrentLevelOneEventThe Battery-String charger current has exceeded the thermal runaway charger current level one threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5611
lgpCondId5612ThermalRunawayChargerCurrentLevelTwoEventThe Battery-String charger current has exceeded the thermal runaway charger current level two threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5612
lgpCondId5617TemperatureControlSensorIssueThe air sensor selected for cooling control is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5617
lgpCondId5621EEVSuperheatBelowThresholdElectronic expansion valve refrigerant low superheat event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5621
lgpCondId5622EEVDischargeTempAboveThresholdElectronic expansion valve refrigerant high discharge temperature event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5622
lgpCondId5623EEVBatteryIssueElectronic expansion valve battery cannot be recharged and needs to be replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5623
lgpCondId5624EEVPowerIssueElectronic expansion valve lost power and is running on battery backup.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5624
lgpCondId5625EEVUnspecifiedGeneralEventOne or more unspecified electronic expansion valve events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5625
lgpCondId5629StaticPressureSensorIssueThe static pressure sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5629
lgpCondId5630HighStaticPressureHigh static pressure event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5630
lgpCondId5631LowStaticPressureLow static pressure event.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5631
lgpCondId5636PumpUnspecifiedGeneralEventOne or more unspecified pump events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5636
lgpCondId5637CondenserUnitUnspecifiedGeneralEventOne or more unspecified condenser unit events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5637
lgpCondId5638CondenserCircuitUnspecifiedGeneralEventOne or more unspecified condenser circuit events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5638
lgpCondId5642SFAReservedEvent1Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5642
lgpCondId5643SFAReservedEvent2Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5643
lgpCondId5644SFAReservedEvent3Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5644
lgpCondId5645SFAReservedEvent4Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5645
lgpCondId5646SFAReservedEvent5Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5646
lgpCondId5647SFAReservedEvent6Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5647
lgpCondId5648SFAReservedEvent7Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5648
lgpCondId5649SFAReservedEvent8Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5649
lgpCondId5650SFAReservedEvent9Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5650
lgpCondId5651SFAReservedEvent10Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5651
lgpCondId5652SFAReservedEvent11Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5652
lgpCondId5653SFAReservedEvent12Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5653
lgpCondId5654SFAReservedEvent13Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5654
lgpCondId5655SFAReservedEvent14Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5655
lgpCondId5656SFAReservedEvent15Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5656
lgpCondId5657SFAReservedEvent16Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5657
lgpCondId5658SFAReservedEvent17Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5658
lgpCondId5659SFAReservedEvent18Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5659
lgpCondId5660SFAReservedEvent19Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5660
lgpCondId5661SFAReservedEvent20Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5661
lgpCondId5662SFAReservedEvent21Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5662
lgpCondId5663SFAReservedEvent22Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5663
lgpCondId5664SFAReservedEvent23Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5664
lgpCondId5665SFAReservedEvent24Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5665
lgpCondId5666SFAReservedEvent25Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5666
lgpCondId5768OutletAirOvertemperatureLimitThe difference between the outlet air temperature and inlet air temperature exceeds a specified maximum temperature.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5768
lgpCondId5769EMOShutdownAn Emergency Module Off command has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5769
lgpCondId5770TopOutletFanFaultTop outlet fan fault - one or more top outlet fans have failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5770
lgpCondId5771MMSOverCapacityThe multi-module system load is larger than the apparent power limit setting.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5771
lgpCondId5773CompressorCapacityNormalCompressor has returned to normal load capacity.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5773
lgpCondId5774CompressorContactorIssueCompressor contactor is not closing during compressor startup or is not opening during compressor shutdown.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5774
lgpCondId5775UnitShutdownUnspecifiedGeneralEventOne or more unspecified unit shutdown events active. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5775
lgpCondId5776PDULowVoltageLNThe system has detected a module under voltage condition (LN).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5776
lgpCondId5777PDULowVoltageLLThe system has detected a module under voltage condition (LL).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5777
lgpCondId5778PDULowVoltageL1L2The system has detected a line-to-line under voltage condition (L1 -L2).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5778
lgpCondId5779PDULowVoltageL2L3The system has detected a line-to-line under voltage condition (L2 -L3).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5779
lgpCondId5780PDULowVoltageL3L1The system has detected a line-to-line under voltage condition (L3 -L1).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5780
lgpCondId5781PDULowVoltageL1NThe system has detected a line to neutral under voltage condition (L1-N).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5781
lgpCondId5782PDULowVoltageL2NThe system has detected a line to neutral under voltage condition (L2-N).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5782
lgpCondId5783PDULowVoltageL3NThe system has detected a line to neutral under voltage condition (L3-N).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5783
lgpCondId5784BranchLowVoltageLNThe system has detected a module under voltage condition (LN).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5784
lgpCondId5785BranchLowVoltageLLThe system has detected a module under voltage condition (LL).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5785
lgpCondId5786BranchLowVoltageThe system has detected a module under voltage condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5786
lgpCondId5788ContTieActiveContinuous Power Tie Active.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5788
lgpCondId5792UserkWhResetThe user kWh accumulator was reset to zero by the operator.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5792
lgpCondId5796PeakkWResetThe Peak kW was reset.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5796
lgpCondId5798BypassOverloadBypass overloaded, reduce load immediately.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5798
lgpCondId5801LowBatteryShutdownImminentIf active and guaranteed shutdown is enabled, a low battery reserve condition exists that will shutdown the UPS.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5801
lgpCondId5806OutputOverloadAn overload exists on the output.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5806
lgpCondId5807OutputOffPendingOutput off pending - shutdown imminent.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5807
lgpCondId5808SystemShutdownOutputShortShutdown was due to a short on the output.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5808
lgpCondId5809SystemShutdownLowBatteryShutdown was due to a low battery condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5809
lgpCondId5810SystemShutdownRemoteShutdownShutdown was due to a remote communications shutdown command.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5810
lgpCondId5811SystemShutdownHardwareFaultShutdown was due to an externally applied hardware control signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5811
lgpCondId5817LossofRedundancyThe system has an insufficient number of power modules to provide redundancy.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5817
lgpCondId5818PowerModuleFailureOne or more conditions indicate a power module failure, service is required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5818
lgpCondId5819PowerModuleWarningOne or more power modules is reporting a warning condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5819
lgpCondId5838PowerModuleFanFaultThe Power Module has detected a fan fault.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5838
lgpCondId5839PowerModuleOverTemperatureThe Power Module has detected an over temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5839
lgpCondId5840PowerModuleShutdownOverTemperaturePower Module has shutdown due to over temperature.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5840
lgpCondId5842ChargerModuleFanFaultThe Charger Module has detected a fan fault.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5842
lgpCondId5847BatteryModuleTemperatureSensorFaultA Battery Module temperature sensor fault has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5847
lgpCondId5848BatteryModuleOverTemperatureThe Battery Module has detected an over temperature condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5848
lgpCondId5849ReplaceBatteryModuleThe Battery Module needs to be replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5849
lgpCondId5850SystemShutdownTransformerOverTemperatureSystem shutdown due to transformer over temperature.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5850
lgpCondId5851MaximumLoadAlarmMaximum load alarm indicating load setting has been exceeded.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5851
lgpCondId5856BatteryModuleFaultOne or more battery modules are reporting a fault condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5856
lgpCondId5857BatteryModuleWarningOne or more battery modules are reporting a warning condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5857
lgpCondId5862CheckAirFilterPlease check air filter, it may need to be cleaned or replaced.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5862
lgpCondId5863TransformerFanFaultThe transformer fan has failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5863
lgpCondId5865NoLoadWarningIndicates the UPS has output voltage but the output current is below a set threshold [No Load Warning Current Threshold] for a set period of time [No Load Warning Delay].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5865
lgpCondId5871BatteryOverTemperatureLimitA battery temperature sensor is reporting a value above a predetermined limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5871
lgpCondId5873UnexpectedMainBatteryDisconnectClosureThe main battery disconnect has closed unexpectedly.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5873
lgpCondId5874BatteryOverVoltageThe system has detected that the battery voltage has exceeded a predetermined limit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5874
lgpCondId5875BatteryFuseFaultOne or more battery fuse faults has occurred.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5875
lgpCondId5878MainBatteryDisconnectForcedToUnlockThe main battery disconnect is forced to the unlocked state.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5878
lgpCondId5879VdcBackfeedThe voltage between battery and DC bus measurements is out of tolerance.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5879
lgpCondId5880RectifierConfigurationChangeRequestThis event indicates that the battery is not configured and PFC is not enabled.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5880
lgpCondId5881RegenerationActiveRegeneration operation is active.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5881
lgpCondId5882RegenerationOperationTerminatedRegeneration operation is not active.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5882
lgpCondId5883RegenerationOperationFailureRegeneration operation has been terminated due to bypass source instability or unit misoperation.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5883
lgpCondId5884ProgramInputContact01When the signal from [Program Input Contact 01] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5884
lgpCondId5885ProgramInputContact02When the signal from [Program Input Contact 02] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5885
lgpCondId5886ProgramInputContact03When the signal from [Program Input Contact 03] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5886
lgpCondId5887ProgramInputContact04When the signal from [Program Input Contact 04] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5887
lgpCondId5888ProgramInputContact05When the signal from [Program Input Contact 05] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5888
lgpCondId5889ProgramInputContact06When the signal from [Program Input Contact 06] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5889
lgpCondId5890ProgramInputContact07When the signal from [Program Input Contact 07] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5890
lgpCondId5891ProgramInputContact08When the signal from [Program Input Contact 08] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5891
lgpCondId5892ProgramInputContact09When the signal from [Program Input Contact 09] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5892
lgpCondId5893ProgramInputContact10When the signal from [Program Input Contact 10] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5893
lgpCondId5894ProgramInputContact11When the signal from [Program Input Contact 11] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5894
lgpCondId5895ProgramInputContact12When the signal from [Program Input Contact 12] is active the function assigned to this contact is executed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5895
lgpCondId5896GroundFaultDetectedThe system has detected a ground fault on a Battery-String.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5896
lgpCondId5902ReturnHumiditySensorIssueThe humidity sensor at the inlet of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5902
lgpCondId5903CompressorLowDifferentialPressureLockoutCompressor exceeded maximum startup attempts due to low differential pressure. Compressor is shutdown and has been disabled.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5903
lgpCondId5906AirflowSensorIssueAirflow sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5906
lgpCondId5907ExtAirDamperPositionIssueAir damper position does not match expected value, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5907
lgpCondId5908ExtPowerSourceAFailureUnit main power source A failure, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5908
lgpCondId5909ExtPowerSourceBFailureUnit main power source B failure, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5909
lgpCondId5910StaticPressureSensorOutofRangeStatic pressure sensor signal is out of its configured range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5910
lgpCondId5911FluidTemperatureSensorIssueThe fluid temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5911
lgpCondId5912FluidFlowSensorIssueThe fluid flow sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5912
lgpCondId5914OverDifferentialPressureAn over differential pressure condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5914
lgpCondId5915UnderDifferentialPressureAn under differential pressure condition was detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5915
lgpCondId5924MixedModeLockoutMixed mode has been entered too many times over a rolling time period and has been temporarily disabled. Mixed mode is defined as the use of a compressor on one refrigeration circuit and the use of a refrigerant pump on the other circuit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5924
lgpCondId5928UnbalancedLoadConditionThe system has detected a line-to-line unbalanced load condition.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5928
lgpCondId5939BranchOverCurrentProtectionThe Branch Receptacle Module's over current protection is triggered.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5939
lgpCondId5948BranchLowVoltageLLThe system has detected a module under voltage condition (LL).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5948
lgpCondId5957BypassInputVoltageFaultThe system has detected the bypass voltage is unqualified.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5957
lgpCondId5958BatteryTemperatureOutofRangeBattery temperature is outside of acceptable range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5958
lgpCondId5960InverterOverloadInverter in overload fault.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5960
lgpCondId5966AuxAirTempDeviceCommunicationLostCommunication with external auxiliary device providing an air temperature value has been lost.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5966
lgpCondId5967ModbusPowerMeterCommunicationLostCommunication with Modbus power meter has been lost.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5967
lgpCondId5968InverterDesaturationInverter Desaturation.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5968
lgpCondId5969GenericDICFaultThe control board reports a fault - Service required.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5969
lgpCondId5970GroundFaultAn AC phase to ground fault or three phase fault to ground exists on the output of the UPS.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5970
lgpCondId5973InputBreakerOpenThe main input breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5973
lgpCondId5974NeutralBreakerOpenThe neutral breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5974
lgpCondId5975OutputBreakerOpenThe output breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5975
lgpCondId5976MaintenanceBypassBreakerClosedThe maintenance bypass breaker is closed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5976
lgpCondId5977BatteryBreakerOpenThe battery circuit is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5977
lgpCondId5978RectifierIsolationBreakerRFBOpenThe rectifier isolation breaker (RFB) indicates that it is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5978
lgpCondId5982BypassBreakerSBBOpenThe bypass circuit breaker (SBB) indicates that it is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5982
lgpCondId5983BypassIsolationBreakerBIBOpenThe bypass isolation breaker (BIB) indicates that it is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5983
lgpCondId5984BypassUndervoltageWarningThe voltage on one or more bypass phases is less than a specified percentage of the nominal voltage.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5984
lgpCondId5985BypassStaticSwitchBPSSOnThe Bypass Static Switch has been turned on.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5985
lgpCondId5998BattOvtempWarningA battery temperature sensor is reporting a value above the setpoint.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.5998
lgpCondId6009InverterOutputBreakerOpenThe inverter output breaker indicates that it is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6009
lgpCondId6011EquipmentOverTempWarningEquipment over temperature warning is a summary event based on the detection of at least one measured temperature exceeding a threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6011
lgpCondId6012EquipmentOvertemperatureLimitThe equipment air temperature has exceeded its maximum set point.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6012
lgpCondId6045RectifierInputBreakerOpenThe rectifier isolation breaker indicates that it is in the open position.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6045
lgpCondId6046LoadonUPSThe output is being supplied power from the inverter.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6046
lgpCondId6047Core2CoreFuseFailureCore-2-core fuse failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6047
lgpCondId6052SystemOutputBreakerOpenThe system output breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6052
lgpCondId6059InverterRelayFaultThe inverter relay has malfunctioned.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6059
lgpCondId6060TransfertoBypassSystemOverloadThe UPS System has transferred to bypass because the active power modules cannot support the critical load.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6060
lgpCondId6061InputSourceBackfeedThe battery is backfeeding the input source.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6061
lgpCondId6062LossofSynchronizationThe inverter and bypass are no longer synchronized. .
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6062
lgpCondId6063BatteryConverterCurrentLimitThe battery converter has reached is maximum current limit. .
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6063
lgpCondId6064LBSCableFailureLoad Bus Sync communications is abnormal. A problem with the LBS cable may exist.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6064
lgpCondId6065BatteryChargeEqualizationTimeoutThe battery equalizing is time out.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6065
lgpCondId6066ParallelCableFailureThe UPS parallel system communications is abnormal. A problem with the parallel cable may exist.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6066
lgpCondId6067BatteryFaultA short circuit exists in the battery system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6067
lgpCondId6068BatteryRoomAlarmThe ambient temperature of the battery room is abnormal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6068
lgpCondId6080UPSCCommunicationFailureThe UPSC has failed to communicate in a designated time period.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6080
lgpCondId6092Compressor1BThermalOverloadFixed compressor 1B is shut down due to thermal overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6092
lgpCondId6093Compressor2BThermalOverloadFixed compressor 2B is shut down due to thermal overload.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6093
lgpCondId6094Compressor1BHoursExceededFixed compressor 1B run hours have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6094
lgpCondId6095Compressor2BHoursExceededFixed compressor 2B run hours have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6095
lgpCondId6100CondenserRemoteShutdownCondenser is shut down by a remote signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6100
lgpCondId6105ExternalCondenserTVSSIssueThe condenser Transient Voltage Surge Suppressor or Surge Protection Device has failed, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6105
lgpCondId6106ExternalCondenserVFDIssueThe condenser fan Variable Frequency Drive is offline, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6106
lgpCondId6107ExternalCondenserIssueCondenser is not operating within its operational parameters, as indicated by an external input signal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6107
lgpCondId6119SlotsnotavailableThe number of sensors exceeds the number of allocated slots and cannot be displayed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6119
lgpCondId6180BatteryUnderVoltageBattery voltage is too low.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6180
lgpCondId6182ReplaceBatteryThe battery is due for replacement.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6182
lgpCondId6186InputFrequencyDeviationThe input frequency is outside of the normal range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6186
lgpCondId6187ShutdownPendingShutdown is pending.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6187
lgpCondId6194SystemRebootCommandIssuedReboot command issued to the system.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6194
lgpCondId6203SensorAddedSensor Added.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6203
lgpCondId6204SensorRemovedSensor Removed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6204
lgpCondId6205WaterLeakDetectedWater leak detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6205
lgpCondId6210FirmwareUpdateInProgressFirmware update has started and is in progress.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6210
lgpCondId6211FirmwareUpdateCompletedSuccessfullyFirmware update has completed successfully.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6211
lgpCondId6212FirmwareUpdateCompletedUnsuccessfullyFirmware update has completed, but was not successful.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6212
lgpCondId6216PrechargeCircuitFailedDC Bus precharge/discharge didn't reach specified level within a specified time.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6216
lgpCondId6217MemoryCardRemovedThe memory card on the control board has been removed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6217
lgpCondId6218AutoCalibrationActiveThe system is automatically calibrating ADC channels.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6218
lgpCondId6219AutoCalibrationFailedADC channel calibration has failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6219
lgpCondId6220ModuleOutputBreakerOpenThe module output breaker is open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6220
lgpCondId6221NeutralVoltageFaultVoltage observed on neutral line.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6221
lgpCondId6222BranchLoadLossLoss of load on branch detected. Branch circuit breaker might be open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6222
lgpCondId6225RemoteSensorLowHumidityRemote sensor humidity has dropped below a lower threshold. The event is deactivated when the humidity rises above the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6225
lgpCondId6226RemoteSensorHighHumidityRemote sensor humidity has exceeded an upper threshold. The event is deactivated when the humidity drops below the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6226
lgpCondId6227RemoteSensorAverageLowHumidityThe average humidity of multiple remote sensors on the cooling unit has dropped below a lower threshold. The event is deactivated when the humidity rises above the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6227
lgpCondId6228RemoteSensorAverageHighHumidityThe average humidity of multiple remote sensors on the cooling unit has exceeded an upper threshold. The event is deactivated when the humidity drops below the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6228
lgpCondId6229RemoteSensorSystemAverageLowHumidityThe average humidity of multiple remote sensors on interconnected cooling units in a single system has dropped below a lower threshold. The event is deactivated when the humidity rises above the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6229
lgpCondId6230RemoteSensorSystemAverageHighHumidityThe average humidity of multiple remote sensors on interconnected cooling units in a single system has exceeded an upper threshold. The event is deactivated when the humidity drops below the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6230
lgpCondId6231LowCompressorSuperheatCompressor suction superheat has dropped below a lower threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6231
lgpCondId6232SECUnspecifiedGeneralEventOne or more unspecified events active for the Superheat and Envelope Controller. See local unit display for further details.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6232
lgpCondId6233SECCommunicationLostCommunication with the Superheat and Envelope Controller has been lost. The event is deactivated when communication is re -established.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6233
lgpCondId6236PowerSourceAIssueNo power is detected at power source input 'A'.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6236
lgpCondId6237PowerSourceBIssueNo power is detected at power source input 'B'.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6237
lgpCondId6239FluidValveHoursExceededOperating hours for the fluid valve have exceeded the threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6239
lgpCondId6253BoosterFailureBooster failure - boost is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6253
lgpCondId6254ChargerFailureCharger Failure - Charger is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6254
lgpCondId6274UnitTopReturnAirSensorFailureReturn air sensor at the top of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6274
lgpCondId6275UnitMiddleReturnAirSensorFailureReturn air sensor in the middle of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6275
lgpCondId6276UnitBottomReturnAirSensorFailureReturn air sensor at the bottom of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6276
lgpCondId6277UnitTopSupplyAirSensorFailureSupply air sensor at the top of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6277
lgpCondId6278UnitMiddleFirstSupplyAirSensorFailureFirst supply air sensor in the middle of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6278
lgpCondId6279UnitBottomSupplyAirSensorFailureSupply air sensor at the bottom of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6279
lgpCondId6284UnitMiddleSecondSupplyAirSensorFailureSecond supply air sensor in the middle of the unit is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6284
lgpCondId6293ChilledWaterControlActiveChilled water inlet temperature control function is enabled due to 'bad' water.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6293
lgpCondId6294ChilledWaterFlowTransducerFailureChilled water flow transducer is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6294
lgpCondId6295ChilledWaterInletTemperatureSensorFailureChilled water inlet temperature sensor is disconnected or the signal is out of range. The sensor is mandatory for the chilled water flow function.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6295
lgpCondId6296ChilledWaterHighInletTemperatureChilled water inlet temperature has exceeded an upper threshold.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6296
lgpCondId6297Modbus010VModuleCommunicationFailureModbus 0-10V module for managing the second Chilled Water circuit valve is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6297
lgpCondId6299RackDoorsOpenRack doors opened due to supply air temperature exceeding the [Rack Door Open High Supply Air Temperature Threshold].
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6299
lgpCondId6303TeamStaticPressureSensorFailureThe team static pressure sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6303
lgpCondId6304HeatingLockoutHeating is shut down and disabled.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6304
lgpCondId6305FreeCoolingStoppedHighRoomTempFree cooling is temporarily disabled due to room temperature exceeding a preset delta above the the set point.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6305
lgpCondId6306ColdAisleTemperatureHumidityTeamSensorFailureCold aisle team sensor measuring air temperature and humidity is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6306
lgpCondId6309ColdAisleAirSensorFailureCold aisle sensor measuring air temperature and humidity is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6309
lgpCondId6310ChilledWaterInletTemperatureControlActiveChilled water inlet temperature control is active.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6310
lgpCondId6313ChilledWaterInletTemperatureSensorFailureChilled water inlet temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6313
lgpCondId6314ChilledWaterOutletTemperatureSensorFailureChilled water outlet temperature sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6314
lgpCondId6315ChilledWaterFlowMeterSensorFailureChilled water flow meter sensor is disconnected or the signal is out of range.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6315
lgpCondId6333BypassoutofsyncBypass and Inverter inputs are not in sync.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6333
lgpCondId6348SystemOutputoffasrequestedThe UPS has shutdown as requested, i.e., the output is off.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6348
lgpCondId6349SystemOffasrequestedThe entire UPS has shutdown as commanded.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6349
lgpCondId6350GeneralFaultA general fault in the UPS has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6350
lgpCondId6351UPSAwaitingPowerThe UPS output is off and the UPS is awaiting the return of input power.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6351
lgpCondId6352AutonomyCalibrationCalibration test occurred.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6352
lgpCondId6353GeneralWarningA warning in the UPS has been detected.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6353
lgpCondId6354BatteryChargingThe UPS battery is charging (battery charge percentage lower than 98).
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6354
lgpCondId6355BackfeedRelayFailureBypass SCR is wrongly on or commutated.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6355
lgpCondId6356BatteryCircuitOpenBattery Circuit Open.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6356
lgpCondId6357SystemRestartPendingA request for UPS restart has been received.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6357
lgpCondId6358PipeTemperatureSensorFailureAir temperature sensor located in the pipe is not sending a valid value.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6358
lgpCondId6362SFAReservedEvent26Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6362
lgpCondId6363SFAReservedEvent27Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6363
lgpCondId6364SFAReservedEvent28Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6364
lgpCondId6365SFAReservedEvent29Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6365
lgpCondId6366SFAReservedEvent30Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6366
lgpCondId6367SFAReservedEvent31Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6367
lgpCondId6368SFAReservedEvent32Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6368
lgpCondId6369SFAReservedEvent33Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6369
lgpCondId6370SFAReservedEvent34Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6370
lgpCondId6371SFAReservedEvent35Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6371
lgpCondId6372SFAReservedEvent36Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6372
lgpCondId6373SFAReservedEvent37Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6373
lgpCondId6374SFAReservedEvent38Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6374
lgpCondId6375SFAReservedEvent39Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6375
lgpCondId6376SFAReservedEvent40Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6376
lgpCondId6377SFAReservedEvent41Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6377
lgpCondId6378SFAReservedEvent42Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6378
lgpCondId6379SFAReservedEvent43Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6379
lgpCondId6380SFAReservedEvent44Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6380
lgpCondId6381SFAReservedEvent45Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6381
lgpCondId6382SFAReservedEvent46Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6382
lgpCondId6383SFAReservedEvent47Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6383
lgpCondId6384SFAReservedEvent48Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6384
lgpCondId6385SFAReservedEvent49Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6385
lgpCondId6386SFAReservedEvent50Reserved event for SFA use.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6386
lgpCondId6438PowerModuleInputCurrentAbnormalInput current of the power module is abnormal.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6438
lgpCondId6439PowerModuleBalancerofDCBusFailureBalancer of DC Bus in the power module has failed.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6439
lgpCondId6440PowerModuleFuseFailureA summary event indicating one or more fuse failures in the power module.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6440
lgpCondId6441PowerModulePowerSupplyFailurePower module power supply failure.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6441
lgpCondId6450PDUPoweredOnThe PDU was powered on.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6450
lgpCondId6453InputWiringFaultThe neutral/ground conductors on the input wiring are not properly bonded, or the line/neutral conductors have been swapped.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6453
lgpCondId6454DCtoDCConverterFaultA failure has occurred in the battery discharge circuit.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6454
lgpCondId6455LeakSensorCableFaultA fault is detected in the 'Leak Sensor' cable.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6455
lgpCondId6518StandbyUnitActivatedDuetoChillerFailureExternal chiller unit has failed for this unit, so the standby cooling unit has been activated.
OBJECT IDENTIFIER
.1.3.6.1.4.1.476.1.42.3.2.7.1.6518