HUAWEI-XDSL-COMMON-MIB
AI MIB Summary
The HUAWEI-XDSL-COMMON-MIB module defines standardized SNMP objects for monitoring and managing Huawei XDSL access network equipment, specifically exposing interface status, line configuration parameters, and physical layer statistics for DSLAMs and ONTs. It enables Network Management Systems to retrieve critical performance metrics such as line attenuation, signal-to-noise ratio, and active session counts across VDSL, ADSL, and G.SHDSL technologies.
This MIB is used for defining Huawei's XDSL common management MIB objects, which provides XDSL management NMS interfaces.
Main OID:
hwXdslCommon.1.3.6.1.4.1.2011.6.148
42
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
42 total| Object Name |
|---|
hwXdslCommonThis MIB is used for defining Huawei's XDSL common management MIB objects,
which provides XDSL management NMS interfaces. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.148 |
hwXdslCommonMib OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.1 |
hwXdslAutoDeleteProfUnused OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.1.1 |
hwXdslAutoDeleteProfUnusedProfTypeThe profile type of deleting unused XDSL profile.
Options:
1. vdsl2LineConfTemplate(1) - Vdsl line template
2. vdsl2LineConfProf(2) - Vdsl line profile
3. vdsl2ChConfProfile(3) - Vdsl channel profile
4. vdsl2LineAlarmConfTemplate(4) - Vdsl line alarm template
5. vdsl2LineAlarmConfProfile(5) - Vdsl line alarm profile
6. vdsl2ChAlarmConfProfile(6) - Vdsl channel alarm profile
7. vdsl2ServProf(7) - Vdsl service profile (TI mode)
8. vdsl2SpectrumProf(8) - Vdsl spectrum profile (TI mode)
9. vdsl2DpboProf(9) - Vdsl DPBO profile (TI mode)
10. vdsl2UpboProf(10) - Vdsl UPBO profile (TI mode)
11. vdsl2NoiseMarginProf(11) - Vdsl noise-margin profile (TI mode)
12. vdsl2DelayInpProf(12) - Vdsl delay-inp profile (TI mode)
13. vopDataRateConfProf(13) - Xdsl data rate profile (TR165 mode)
14. vopLineSpectrumConfProf(14) - Xdsl line spectrum profile (TR165 mode)
15. vopUPBOConfProf(15) - Xdsl UPBO profile (TR165 mode)
16. vopDPBOConfProf(16) - Xdsl DPBO profile (TR165 mode)
17. vopRFIConfProf(17) - Xdsl RFI profile (TR165 mode)
18. vopSNRMarginConfProf(18) - Xdsl SNR margin profile (TR165 mode)
19. vopINPDelayConfProf(19) - Xdsl INP delay profile (TR165 mode)
20. vopVirtualNoiseConfProf(20) - Xdsl virtual noise profile (TR165 mode)
21. vopModeSpecificPSDConfProf(21) - Xdsl mode specific PSD profile (TR165 mode)
22. adsl2LineConfTemplate(22) - Adsl line template (RFC4706 mode)
23. adsl2LineConfProf(23) - Adsl line profile (RFC4706 mode)
24. adsl2ChConfProfile(24) - Adsl channel profile (RFC4706 mode)
25. adsl2LineAlarmConfTemplate(25) - Adsl line alarm template (RFC4706 mode)
26. adsl2LineAlarmConfProfile(26) - Adsl line alarm profile (RFC4706 mode)
27. adsl2ChAlarmConfProfile(27) - Adsl channel alarm profile (RFC4706 mode)
28. adslLineConfProfile(28) - Adsl line profile (RFC2662 mode)
29. adslLineAlarmConfProfile(29) - Adsl line alarm profile (RFC2662 mode)
30. adslLineExtConfProfile(30) - Adsl line ext profile (RFC2662 mode)
31. shdslLineConfProfile(31) - Shdsl line profile
32. shdslAlarmConfProfile(32) - Shdsl alarm profile
33. vopINMConfProf(33) - Xdsl INM profile (TR165 mode)
34. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.148.1.1.1 |
hwXdslAutoDeleteProfUnusedOperTypeThe operation type of deleting unused xDSL profile.
Options:
1. first(1) - Delete the first unused xDSL profile
2. all(2) - Delete all the unused xDSL profile
3. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.148.1.1.2 |
hwXdslLineTableThe table hwXdslLineTable contains status
parameters of xDSL line. The index of this table is
ifIndex. SEQUENCE OF HwXdslLineEntry .1.3.6.1.4.1.2011.6.148.1.2 |
hwXdslLineEntryThe table hwXdslLineTable contains status
parameters of xDSL line. The index of this entry is ifIndex. HwXdslLineEntry .1.3.6.1.4.1.2011.6.148.1.2.1 |
hwAllChActDataRateDsThe downstream actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. This is the sum of net date rates
that all bearer channels operating at.ro Unsigned32 UNITS "bits/second" .1.3.6.1.4.1.2011.6.148.1.2.1.1 |
hwAllChActDataRateUsThe upstream actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. This is the sum of net date rates
that all bearer channels operating at.ro Unsigned32 UNITS "bits/second" .1.3.6.1.4.1.2011.6.148.1.2.1.2 |
hwXdslPortFrequentRetrainControlTableThe table hwXdslPortFrequentRetrainControlTable contains information
of xDSL port frequent retrain control policy.
The index of this table is ifIndex. SEQUENCE OF HwXdslPortFrequentRetrainControlEntry .1.3.6.1.4.1.2011.6.148.1.3 |
hwXdslPortFrequentRetrainControlEntryThe table hwXdslPortFrequentRetrainControlTable contains information
of xDSL port frequent retrain control policy.
The index of this entry is ifIndex. HwXdslPortFrequentRetrainControlEntry .1.3.6.1.4.1.2011.6.148.1.3.1 |
hwXdslPortFrequentRetrainControlTimesThe times that xDSL port frequent retrain.
The invalid value is 4294967295.
If board does not support the operation, the invalid value will be returned.rw Unsigned32 (3..15 | 4294967295) .1.3.6.1.4.1.2011.6.148.1.3.1.1 |
hwXdslPortFrequentRetrainControlPolicyThe control policy that xDSL port frequent retrain.
Options:
1. lock(1) - The port is not allowed to go online within 15 minutes
2. nolimit(2) - The port can go online without the limitation of control policies
3. postponed(3) - The port can go online after a postponed time when the number of frequent
resynchronizations on the port reaches the threshold
4. invalidValue(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.148.1.3.1.2 |
hwXdslPortFrequentRetrainControlPostponedTimeThe postponed time when control policy of xDSL port frequent retrain is postponed.
The invalid value is 4294967295.
If board does not support the operation, the invalid value will be returned.rw Unsigned32 (5..3600 | 4294967295) UNITS "minute" .1.3.6.1.4.1.2011.6.148.1.3.1.3 |
hwXdslAttndrConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.1.4 |
hwXdslAttndrMethodThis parameter specifies the method to be used for the calculation of the ATTNDR
in the downstream and upstream direction. The parameter can take three values 0, 1 and 2.
Options:
1. attndrMethod0(0) - The basic Attainable Net Data Rate method
2. attndrMethod1(1) - The improved Attainable Net Data Rate method, If the control
parameter attndr_method is set to a value of 1, the VTU-O and
VTU-R shall use the impulse noise protection limit INP_min0 with
value as indicated in O-TPS. If O-TPS configures for dual bearer
channel mode, then the highest INP_MINn over the bearer channels
shall be used 1
3. attndrMethod2(2) - The improved Attainable Net Data Rate method, If the control parameter
attndr_method is set to a value of 2, the VTU-O and VTU-R shall use an
impulse noise protection limit INP_MIN0 = 0rw Enumeration .1.3.6.1.4.1.2011.6.148.1.4.1 |
hwXdslADSL1INPAdaptionConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.1.5 |
hwXdslADSL1INPAdaptionEnable/Disable the global ADSL1 INP Adaption configuration. This object is defaulted disable(2).
This configuration will take effect after port manually reactivated or board reset.
Options:
1. enable(1) - Enable the ADSL1 INP Adaption configuration
2. disable(2) - Disable the ADSL1 INP Adaption configurationrw Enumeration .1.3.6.1.4.1.2011.6.148.1.5.1 |
hwXdslTrapsVbOids OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.2 |
hwXdslDynamicCollectResultDynamic information collecting result.
Options:
1. noFail(0) - The dynamic info has been collected successful
2. memFull(1) - The memory used for dynamic info collecting is full
3. otherCause(2) - Other collect failure reasonro Enumeration .1.3.6.1.4.1.2011.6.148.2.1 |
hwXdslDynamicCollectTimeTime of the Dynamic information file.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.148.2.2 |
hwXdslRequestIDRequest ID.ro Integer32 .1.3.6.1.4.1.2011.6.148.2.3 |
hwXdslSeltCompleteResultSelt test complete result.
Options:
1. success(1) - Selt test is successful
2. fail(2) - Failed in selt testro Enumeration .1.3.6.1.4.1.2011.6.148.2.4 |
hwAdslProfIDTypeType of the adsl template ID.
Options:
1. lineTemplate(1) - Indicates line template ID
2. alarmTemplate(2) - Indicates alarm template ID
3. extProfile(3) - Indicates ext profile IDro Enumeration .1.3.6.1.4.1.2011.6.148.2.5 |
hwXdslProfNameThe name of the XDSL profile.ro OCTET STRING .1.3.6.1.4.1.2011.6.148.2.6 |
hwXdslPortActualUpRateXdsl port actual upstream rate.ro Unsigned32 .1.3.6.1.4.1.2011.6.148.2.7 |
hwXdslPortActualDownRateXdsl port actual downstream rate.ro Unsigned32 .1.3.6.1.4.1.2011.6.148.2.8 |
hwXdslDelProfIndexIndex of the profile which is deleted.
If you delete all the profiles unused, this parameter will be 0xffffffff.ro Unsigned32 .1.3.6.1.4.1.2011.6.148.2.9 |
hwXdslDelProfNameName of the profile which is deleted.
If you delete all the profiles unused, this parameter will be a zero string.ro OCTET STRING .1.3.6.1.4.1.2011.6.148.2.10 |
hwXdslSeltTestStartResultXDSL selt test start result.
Options:
1. normal(1) - This notification indicates that a SELT task has been started successfully
2. failed(2) - This notification indicates that a SELT task failed to be startedro Enumeration .1.3.6.1.4.1.2011.6.148.2.11 |
hwXdslTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.3 |
hwXdslCommonTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.3.1 |
hwXdslCommonTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.3.1.0 |
hwXdslDynamicCollectInfoTrapXDSL dynamic collect trap.
This trap message is generated when XDSL dynamic collected. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.1.0.1 |
hwXdslSeltCompleteResultTrapSelt test complete result trap.
This trap message is generated when selt test completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.1.0.2 |
hwAdslProfIDChangeTrapAdsl profile ID change trap.
This trap message is generated when adsl profile ID changed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.1.0.3 |
hwXdslProfDeleteTrapThis trap message is generated when Xdsl unused profile trap deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.1.0.4 |
hwXdslSeltStartResultTrapXDSL selt test start trap.
This notification indicates trap when xDSL selt test start. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.1.0.5 |
hwXdslAlarmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.3.2 |
hwXdslAlarmTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.148.3.2.0 |
hwXdslAutoDeactivateLackLicensesAlarmTrapThis trap message is generated when some xDSL ports or all the xDSL ports
are automatically deactivated due to lack of licenses. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.2.0.1 |
hwXdslPortActRateLowerThresholdAlarmTrapThis trap message is generated when the activation rate
of the xDSL line is lower than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.148.3.2.0.2 |