HUAWEI-VDSL2-PRIV-MIB
AI MIB Summary
The HUAWEI-VDSL2-PRIV-MIB enables vendor-specific monitoring and management of Huawei VDSL2 line parameters, including physical layer statistics, line profile configurations, and error counters for DSLAM and modem interfaces. This module facilitates granular troubleshooting of VDSL2 service delivery by exposing proprietary attributes not covered in standard ITU-T MIBs.
This MIB is used for defining Huawei's vdsl2 priv management MIB objects.
Main OID:
vdsl2Priv.1.3.6.1.4.1.2011.6.115.1.7
45
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
45 total| Object Name |
|---|
vdsl2PrivThis MIB is used for defining Huawei's vdsl2 priv management MIB objects. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.115.1.7 |
vdsl2Test OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.115.1.7.1 |
vdsl2SeltTestTableThis table contains the VDSL SELT configuration, SELT result, SELT data. The index of this table is ifIndex. SEQUENCE OF VDSL2SELTTESTENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.1 |
vdsl2SeltTestEntryThis table contains the VDSL SELT configuration, SELT result, SELT data. The index of this entry is ifIndex. VDSL2SELTTESTENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.1.1 |
vdsl2SeltTestOperTypeThis object is used to start the VDSL SELT. Only the start of the SELT is supported current. The stop of the SELT is not supported.rw VSDLSELTOPERTYPE .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.1 |
vdsl2SeltTestOperResultSelt test operation result.ro VSDLSELTOPERRESULT .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.2 |
vdsl2SeltTestResultNoSelt test result serial number.ro Integer32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.3 |
vdsl2SeltTestResultLastFlagLast package flag for test result.ro VSDLSELTRESULTLASTFLAG .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.4 |
vdsl2SeltTestResultSelt test result data.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.5 |
vdsl2SeltTestParamLoopLengthSelt test parameter Loop Length.ro Integer32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.6 |
vdsl2SeltTestParamLoopTerminSelt test parameter Loop Termination.ro VSDLSELTPARAMLOOPTERMIN .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.7 |
vdsl2SeltTestParamLoopGaugeSelt test parameter Loop Gauge.rw VSDLSELTPARAMLOOPGAUGE .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.8 |
vdsl2SeltTestParamUpShnCapSelt test parameter Upstream Shannon Capacity.ro Integer32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.9 |
vdsl2SeltTestParamDwnShnCapSelt test parameter Downstream Shannon Capacity.ro Integer32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.10 |
vdsl2SeltTestParamInbandNoiseSelt test parameter Inband Noise
4096 values that indicate inband noise in DB/Hz,
covering VDSL bands, from 0 to 30 MHz.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.11 |
vdsl2SeltTestParamTerminRespSelt test parameter Termination Response
180 values that indicate termination response magnitude from 0 to 18 kft.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.12 |
vdsl2SeltTestParamUpMgnAtRateSelt test parameter Upstream Rate vs. Margin
This value is a measure of the quality of your upstream data
signal relative to the noise on the line. Hundreds of values that
indicate SNR margin in DB/Hz at a particular bit rate are provided,
at a certain increments, up to 30 Mbps. This information may be plotted
with the bit rate on the X-axis and the SNR margin on the Y-axis.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.13 |
vdsl2SeltTestParamDwnMgnAtRateSelt test parameter Downstream Rate vs. Margin
This value is a measure of the quality of your downstream data
signal relative to the noise on the line. Hundreds of values that
indicate SNR margin in DB/Hz at a particular bit rate are provided,
at a certain increments, up to 30 Mbps. This information may be plotted
with the bit rate on the X-axis and the SNR margin on the Y-axis.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.14 |
vdsl2SeltTestParamUpRateAtMgnSelt test parameter Upstream Margin vs. Ratero OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.15 |
vdsl2SeltTestParamDwnRateAtMgnSelt test parameter Downstream Margin vs. Ratero OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.16 |
hwvdsl2SeltTestParamAttnAt180KHZSelt test parameter AttnAt180KHZ.
It ranges from -950 to 0 (physical values are -95 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is generated
because the SELT is incomplete, or no SELT data can be obtained from
the port because the SELT data is aged and cleared, the invalid value will be returned.
Unit: 0.1 dBro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65535 |
hwvdsl2SeltTestParamAttnAt300KHZSelt test parameter AttnAt300KHZ.
It ranges from -950 to 0 (physical values are -95 to 0 dB).
The invalid value is -1. If no SELT is performed, no SELT data is generated
because the SELT is incomplete, or no SELT data can be obtained from
the port because the SELT data is aged and cleared, the invalid value will be returned.
Unit: 0.1 dBro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65536 |
hwvdsl2SeltTestParamQSPsdValueSelt test parameter QuietSignal PSD.
An array of 4096 16-bits values,
designed for supporting up to 4096 (downstream) sub-carriers.
It ranges from -150 to -40 units of 1dBm/Hz.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65537 |
hwvdsl2SeltTestParamUnCalibLineScaleThe scale factor of uncalibrated echo response shall be coded as a 32 bit unsigned integer.ro Unsigned32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65538 |
hwvdsl2SeltTestParamUnCalibEchoRespRealSegment1The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1)*UER_G*Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^(-31) and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65539 |
hwvdsl2SeltTestParamUnCalibEchoRespRealSegment2The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1)*UER_G*Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^(-31) and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65540 |
hwvdsl2SeltTestParamUnCalibEchoRespImgSegment1The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1)*UER_G*Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^(-31) and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65541 |
hwvdsl2SeltTestParamUnCalibEchoRespImgSegment2The uncalibrated echo response, UER(i* UER_G*Df), shall be represented in linear format by a
scale factor and a normalized complex number a(i)+j*b(i), where i is a frequency index i ranging
from 0 to NSC-1, the subcarrier spacing, Df = 4.3125 kHz, and (NSC-1)*UER_G*Df is the
highest frequency supported by the SELT-PMD functionality. The UER granularity parameter,
UER_G, has two valid values: 1 and 2, indicating whether the measurements were performed using
a tone spacing of 4.3125 kHz or of 8.625 kHz. If the uncalibrated echo response is being reported
over a frequency range of 17.664 MHz or lower, UER_G shall be set to 1. If the uncalibrated echo
response is being reported over a frequency range that is greater than 17.664 MHz, UER_G shall be
set to 2.
The scale factor shall be coded as a 32-bit unsigned integer. Both a(i) and b(i) shall be coded as
32-bit 2's complement signed integers. The value of UER(i* UER_G*Df) shall be defined as:
UER(i* UER_G*Df) = (scale/2^31)*(a(i)+j*b(i))/2^31. In order to maximize precision, the scale factor
shall be chosen such that max(|a(i)|, |b(i)|) over all i is equal to 2^31-1.
NOTE - This data format supports an UER(f) granularity of 2^(-31) and an UER(f) dynamic range of
approximately +6 dB to -186 dB, however it does not imply any future accuracy requirements.
An UER(i*UER_G* Df) value indicated as a(i) = b(i) = -2^31 is a special value. It indicates that no
measurement could be done for this subcarrier either because it is not supported by the SELT-PMD
function, or that the value is out of range to be represented.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65542 |
hwvdsl2SeltTestParamQlnGroupSizeNumber of QLN(quiet line noise) per group.
The scale value is 1 or 4294967295.4294967295 is invalid value.ro Unsigned32(1 | 4294967295) .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65548 |
hwvdsl2SeltTestParamQmeCThe status of QLN capture switch.
Options:
1. enable(1) - Enable QLN capture switch
2. disable(2) - Disable QLN capture switch
3. invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65549 |
hwvdsl2SeltTestParamUmeCThe status of UER capture switch.
Options:
1. enable(1) - Enable UER capture switch
2. disable(2) - Disable UER capture switch
3. invalid(-1) - Invalid valuerw Enumeration .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65550 |
hwvdsl2SeltTestParaVarUerCThe relative variance of the uncalibrated echo response REL_VAR_UER(i* UER_G *Df) shall be
represented as an 8-bit unsigned integer v(i), where i is the subcarrier index i = 0 to NSC-1. The
value of REL_VAR_UER(i* UER_G *Df) shall be defined as REL_VAR_UER(i* UER_G *Df) = 3 - v(i)/2 dB.
The number v(i) is an 8-bit unsigned integer in the range 0 to 254.
This data format supports a REL_VAR_UER(i) over a range from -124 dB to +3 dB for each carrier with a granularity from 0.5 dB.
Out of range values shall be clamped to the closest range bound.
The special value v(i) = 255 indicates that no measurement is available for that carrier.
Unit: 0.5dBro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65551 |
hwvdsl2SeltTestParaUerMmdCThis parameter is the maximum allowed time for SELT uncalibrated echo response measurement,
between the time of the start command written by the SELT-PMD-ME, and the time the result is
available for read operation by SELT-PMD-ME.
It is configurable between 5 seconds and 240 seconds, in steps of 1 second, Invalid value is 0xff.
Unit: 1 secondrw Unsigned32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65552 |
hwvdsl2SeltTestParaQlnMmdCThis parameter is the maximum allowed time for SELT quiet line noise measurement, between the
time of the start command written by the SELT-PMD-ME, and the time the result is available for
read operation by SELT-PMD-ME.
It is configurable between 1 second and 240 seconds, in steps of 1 second. Invalid value is 0xff.
Unit: 1 secondrw Unsigned32 .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65553 |
hwvdsl2SeltTestParaUerStatusUerStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - The status is failed.ro Enumeration .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65554 |
hwvdsl2SeltTestParaQlnStatusQlnStatus.
Options:
1.off(1) - The status is off.
2.running(2) - The status is running.
3.completed(3) - The status is completed.
4.failed(4) - The status is failed.ro Enumeration .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65555 |
hwvdsl2SeltTestParamCalcEnableThe status of calculation switch.
Options:
1. enable(1) - Enable calculation switch
2. disable(2) - Disable calculation switch
3. invalid(-1) - Invalid value
Default: enable(1)rw Enumeration .1.3.6.1.4.1.2011.6.115.1.7.1.1.1.65556 |
vdsl2SeltTestLevelTableThis table supports the configuration of vdsl selt level.
The indexes of this table are hwFrameIndex and hwSlotIndex. SEQUENCE OF VDSL2SELTTESTLEVELENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.2 |
vdsl2SeltTestLevelEntryThis table supports the configuration of vdsl selt level.
The indexes of this entry are hwFrameIndex and hwSlotIndex. VDSL2SELTTESTLEVELENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.2.1 |
hwvdsl2SeltLevelThe level of vdsl SELT:
1 Level0;
2 Level1;
3 Level2;
4 Level3.
A special value of -1 indicates the level of vdsl SELT is invalid.rw Integer32 (-1 | 1..4) .1.3.6.1.4.1.2011.6.115.1.7.1.2.1.1 |
vdsl2SeltCalibrationTableThis table describes calibration data of selt test.
The index of this table is ifIndex. SEQUENCE OF HWVDSL2SELTCALIBRATIONTENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.3 |
vdsl2SeltCalibrationEntryThis table describes calibration data of selt test.
The index of this entry is ifIndex. HWVDSL2SELTCALIBRATIONTENTRY .1.3.6.1.4.1.2011.6.115.1.7.1.3.1 |
vdsl2SeltCalibrationInvVendorIdIt consists of 8 binary octets, including a
provider code.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.3.1.1 |
vdsl2SeltCalibrationDataSegment1The part 1 of selt calibration data.
The unit of selt calibration data is 0.00001.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.3.1.2 |
vdsl2SeltCalibrationDataSegment2The part 2 of selt calibration data.
The unit of selt calibration data is 0.00001.ro OCTET STRING .1.3.6.1.4.1.2011.6.115.1.7.1.3.1.3 |