HUAWEI-NGADSL-LINE-MIB
AI MIB Summary
The HUAWEI-NGADSL-LINE-MIB extends RFC 4706 to monitor and manage physical layer parameters and performance counters for Huawei Next-Generation ADSL (NGADSL) line interfaces. It provides visibility into ADSL2+ specific metrics such as line attenuation, signal-to-noise ratio, and error statistics for troubleshooting copper access network connectivity.
The MIB is used for defining HUAWEI NGADSL LINE MIB objects, which expand from RFC4706 ADSL2-LINE MIB.
Main OID:
hwadsl2MIB.1.3.6.1.4.1.2011.6.138
266
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
266 total| Object Name |
|---|
adsl2LineStatusCodingGainDsThe actual value of Coding gain upstream parameter,it ranges
from 0 to 16.
Unit: 0.5 dBro Unsigned32 UNITS "0.5 dB" .1.3.6.1.2.1.10.1.1.1.1.1.65535 |
adsl2LineStatusCodingGainUsThe actual value of Coding gain downstream parameter,it ranges
from 0 to 16.
Unit: 0.5 dBro Unsigned32 UNITS "0.5 dB" .1.3.6.1.2.1.10.1.1.1.1.1.65536 |
adsl2LineStatusPcbDsIndicates Power Cut-back on downstream direction.
It ranges from 0 to 400 units of 0.1 dB (physical values
are 0 to 40 dB).
Unit: tenth dBro Unsigned32 UNITS "tenth dB" .1.3.6.1.2.1.10.1.1.1.1.1.65537 |
adsl2LineStatusPcbUsIndicates Power Cut-back on upstream direction.
It ranges from 0 to 400 units of 0.1 dB (physical values
are 0 to 40 dB)
Unit: tenth dBro Unsigned32 UNITS "tenth dB" .1.3.6.1.2.1.10.1.1.1.1.1.65538 |
hwadsl2DynamicprofileThe value of this object identifies the row
in the ADSL Dynamic Profile Table,which applies to this
ADSL line, and channels if applicable.
NULL - indicates that there is no Dynamic profile
bound to this port.rw OCTET STRING .1.3.6.1.2.1.10.1.1.1.1.1.65539 |
adsl2ChStatusINPThe actual impulse noise protection (INP) on
the bearer channel in L0 state.
Unit: 0.1 DMT symbolro Unsigned32 .1.3.6.1.2.1.10.1.1.2.1.1.65535 |
adsl2ChStatusRSRedundancyThe actual number of Reed-Solomon redundancy
bytes per codeword used in the latency path
in which the bearer channel is transported.
The value is coded in bytes.
The value 0 indicates no Reed-Solomon coding.
Unit: bytero Unsigned32 .1.3.6.1.2.1.10.1.1.2.1.1.65536 |
adsl2ChStatusRSSymbolsThe DMT Symbol number per codeword used in
the latency path in which the bearer channel
is transported.
Unit: 0.01 DMT symbolro Unsigned32 UNITS "0.01 DMT symbol" .1.3.6.1.2.1.10.1.1.2.1.1.65537 |
adsl2ChStatusInterDepthThe actual Reed-Solomon codeword size used
in the latency path in which the bearer channel
is transported.
The value ranges from 1 to 4096 by step of 1.
The value 1 indicates no interleaving.ro Unsigned32 .1.3.6.1.2.1.10.1.1.2.1.1.65538 |
adsl2ChStatusSymbolLengthThe actual number of bits per symbol assigned
to the latency path in which the bearer channel
is transported.
This value does not include trellis overhead.
Unit: bitro Unsigned32 .1.3.6.1.2.1.10.1.1.2.1.1.65539 |
adsl2ChStatusRSSizeThe actual Reed-Solomon codeword size used
in the latency path in which the bearer channel
is transported.
Unit: bytero Unsigned32 .1.3.6.1.2.1.10.1.1.2.1.1.65540 |
adsl2SCStatusTxPSDThe PSD MASK per sub-carrier.An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-carriers.
It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values
are -140 to -30 dBm/Hz)
Unit: 0.1 dBm/Hzro OCTET STRING .1.3.6.1.2.1.10.1.1.2.2.1.65535 |
adsl2SCStatusSnrMarginsSNR Margin is the maximum increase in dB of the noise power
received at the ATU (ATU-R on downstream direction and ATU-C
on upstream direction), such that the BER requirements are met
for all bearer channels received at the ATU. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to 63 dB).
Unit: 0.1 dBro OCTET STRING .1.3.6.1.2.1.10.1.1.2.2.1.65536 |
adsl2PMLEverBeforeFecsCount of seconds since agent reset that there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.1.1.4.1.1.1.65535 |
adsl2PMLEverBeforeEsCount of seconds since agent reset that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.1.1.4.1.1.1.65536 |
adsl2PMLEverBeforeSesCount of seconds since agent reset that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.1.1.4.1.1.1.65537 |
adsl2PMLEverBeforeLossCount of seconds since agent reset that there was LOS (or
LOS-FE for ATU-R).
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.1.1.4.1.1.1.65538 |
adsl2PMLEverBeforeUasCount of seconds in Unavailability State since agent reset.
Unavailability begins at the onset of 10 contiguous severely
-errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.2.1.10.1.1.4.1.1.1.65539 |
adsl2PMLInitEverBeforeFullInitsCount of full initializations attempted on the line
(successful and failed) since agent reset.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.1.2.1.65535 |
adsl2PMLInitEverBeforeFailedFullInitsCount of failed full initializations on the line since agent
reset.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.1.2.1.65536 |
adsl2PMLInitEverBeforeShortInitsCount of short initializations attempted on the line
(successful and failed) since agent reset.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.1.2.1.65537 |
adsl2PMLInitEverBeforeFailedShortInitsCount of failed short initializations on the line since agent
reset.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.1.2.1.65538 |
adsl2PMChEverBeforeCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel since agent reset. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.2.1.1.65535 |
adsl2PMChEverBeforeCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel since agent reset. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels.ro Unsigned32 .1.3.6.1.2.1.10.1.1.4.2.1.1.65536 |
adsl2LConfProfTrellisModeEnable and disable the trellis mode. This
object is defaulted enabled(2).
Options:
1. disable(1) - Disable the trellis
2. enable(2) - Enable the trellisrw Adsl2TrellisMode .1.3.6.1.2.1.10.1.1.5.1.2.1.65535 |
adsl2LConfProfBitSwapDsEnable and disable the bit swap downstream of a line.
This object is defaulted enable(2).
Options:
1. disable(1) - Disable the bit swap downstream of a line
2. enable(2) - Enable the bit swap downstream of a linerw Adsl2BitSwap .1.3.6.1.2.1.10.1.1.5.1.2.1.65536 |
adsl2LConfProfBitSwapUsEnable and disable the bit swap upstream of a line.
This object is defaulted enable(2).
Options:
1. disable(1) - Disable the bit swap upstream of a line
2. enable(2) - Enable the bit swap upstream of a linerw Adsl2BitSwap .1.3.6.1.2.1.10.1.1.5.1.2.1.65537 |
adsl2LConfProfDpboEPsdThis parameter defines the PSD mask that is assumed to be permitted at the exchange.
This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints
for DPBOEPSD is 16.
This is a string of 16 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1
Octets 3-5 - Same, for a 2nd breakpoint
Octets 6-8 - Same, for a 3rd breakpoint
This architecture continues until octets 45-47, which are
associated with a 16th breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 16, all remaining
octets are set to the value 0xff.
Unit: 0.5dBm/Hzrw Adsl2DpboEpsd UNITS "0.5dBm/Hz" .1.3.6.1.2.1.10.1.1.5.1.2.1.65538 |
adsl2LConfProfDpboEsELThis configuration parameter defines the assumed electrical length of
cables (E-side cables) connecting exchange based DSL services to a remote
flexibility point (cabinet), that hosts the xTU-C that is subject to
spectrally shaped downstream power back-off depending on this length.
For this parameter the electrical length is defined as the loss (in dB)
of an equivalent length of hypothetical cable at a reference frequency
defined by the network operator or in spectrum management regulations.
DPBOESEL shall be coded as an unsigned integer representing an electrical
length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB.
All values in the range are valid.If DPBOESEL is set to zero, the DPBO in
this section shall be disabled.
This object is defaulted 0.
Unit: 0.5dBrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65539 |
adsl2LConfProfDpboEsCableModelAThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.
This object is defaulted 256.rw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65540 |
adsl2LConfProfDpboEsCableModelBThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.This object is
defaulted 512.rw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65541 |
adsl2LConfProfDpboEsCableModelCThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.This object is
defaulted 256.rw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65542 |
adsl2LConfProfDpboMusDPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for
exchange based services, used to modify parameter DPBOFMAX defined below. It
shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz
(coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz.
All values in the range are valid.This object is defaulted 180.
Unit: 0.5dBm/Hzrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65543 |
adsl2LConfProfDpboFMinDPBOFMIN defines the minimum frequency from which the DPBO shall be applied.
It shall be coded as a 16 bits unsigned integer representing a frequency in
multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0)
to 8832 kHz (coded as 2048). This object is defaulted 0.
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65544 |
adsl2LConfProfDpboFMaxDPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be
coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz.
The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956).
This object is defaulted 511.
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.1.2.1.65545 |
adsl2ChAlarmConfProfileMonitoringRateDsThe channel monitoring rate downstream.
When the value you set is larger than
the value of the rate downstream defined in the channel
profile, it will not be successful. The value 0 means
that no threshold is specified for the associated
counter. This object is defaulted 0.
Unit: bits/secondrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.3.3.1.65535 |
adsl2ChAlarmConfProfileMonitoringRateUsThe channel monitoring rate upstream.
When the value you set is larger than
the value of the rate upstream defined in the channel
profile, it will not be successful. The value 0 means
that no threshold is specified for the associated
counter. This object is defaulted 0.
Unit: bits/secondrw Unsigned32 .1.3.6.1.2.1.10.1.1.5.3.3.1.65536 |
adsl2Mode OBJECT IDENTIFIER .1.3.6.1.2.1.10.1.1.65535 |
hwadslmodecfgThis object is used to change ADSL management mode.
After the mode being changed, system will automatically
save data and reboot.
Options:
1. rfc2662(1) - Management model based on RFC2662 and RFC3440
2. rfc4706(2) - Management model based on RFC4706
3. tr165(3) - Management model based on TR-165rw Adsl2CfgMode .1.3.6.1.2.1.10.1.1.65535.1 |
hwadslabrmodecfgThis object is used to change abr-calculation mode.
Options:
1. normalMode(1) - Change mode to normal abr-calculation
2. ptMode(2) - Change mode to pt abr-calculationrw Enumeration .1.3.6.1.2.1.10.1.1.65535.2 |
hwadsl2MIBThe MIB is used for defining HUAWEI NGADSL LINE MIB objects, which
expand from RFC4706 ADSL2-LINE MIB. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.138 |
hwadsl2 OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1 |
hwadsl2Notifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.0 |
hwadsl2Line OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.1 |
hwadsl2LineTableThe table hwadsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).
Several objects in this table MUST be maintained in a
persistent manner. SEQUENCE OF Hwadsl2LineEntry .1.3.6.1.4.1.2011.6.138.1.1.1 |
hwadsl2LineEntryThe table hwadsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this entry is an interface index where the
interface has an ifType of adsl2plus(238).
Several objects in this table MUST be maintained in a
persistent manner. Hwadsl2LineEntry .1.3.6.1.4.1.2011.6.138.1.1.1.1 |
hwadsl2LineStatusCodingGainDsInfoThe actual value of Coding gain upstream parameter,it ranges
from 0 to 16 units of 0.5 dB.
Unit: 0.5 dBro Unsigned32 UNITS "0.5 dB" .1.3.6.1.4.1.2011.6.138.1.1.1.1.1 |
hwadsl2LineStatusCodingGainUsInfoThe actual value of Coding gain downstream parameter,it ranges
from 0 to 16 units of 0.5 dB.
Unit: 0.5 dBro Unsigned32 UNITS "0.5 dB" .1.3.6.1.4.1.2011.6.138.1.1.1.1.2 |
hwadsl2LineStatusPcbDsInfoIndicates Power Cut-back on downstream direction.
It ranges from 0 to 400 units of 0.1 dB (physical values
are 0 to 40 dB).
Unit: tenth dBro Unsigned32 UNITS "tenth dB" .1.3.6.1.4.1.2011.6.138.1.1.1.1.3 |
hwadsl2LineStatusPcbUsInfoIndicates Power Cut-back on upstream direction.
It ranges from 0 to 400 units of 0.1 dB (physical values
are 0 to 40 dB) and the invalid value is 4294967295.
Unit: tenth dBro Unsigned32 UNITS "tenth dB" .1.3.6.1.4.1.2011.6.138.1.1.1.1.4 |
hwadsl2DynamicprofileInfoThe value of this object identifies the row
in the ADSL Dynamic Profile Table,which applies to this
ADSL line, and channels if applicable.
NULL -Indicates that there is no Dynamic profile
bound to this port.rw OCTET STRING .1.3.6.1.4.1.2011.6.138.1.1.1.1.5 |
hwadsl2LineStatusInitResultIndicates the result of the last full initialization performed
on the line.
Options:
1. noFail(0) - Successful initialization
2. configError(1) - Configuration failure
3. configNotFeasible(2) - Configuration details not supported
4. commFail(3) - Communication failure
5. noPeerXtu(4) - Peer xTU not detected
6. otherCause(5) - Other initialization failure reason
7. ginpNotSelected(6) - G.998.4 Retransmission mode was not selected
while RTX_MODE = FORCED or with RTX_MODE = RTX_TESTMODE
8. invalidValue(-1) - Invalid valuero Hwadsl2InitResult .1.3.6.1.4.1.2011.6.138.1.1.1.1.6 |
hwadsl2LineStatusRtxUsedDsThis parameter specifies whether G.998.4 retransmission
is used in a given transmit direction.
Options:
1. rtxInuse(1) - RTX in use
2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MODE = FORBIDDEN
3. rtxUnusedNotSupportedXtuc(3) - RTX not in use, due to not supported by the XTU-C
4. rtxUnusedNotSupportedXtur(4) - RTX not in use, due to not supported by the XTU-R
5. rtxUnusedNotSupportedXtucAndXtur(5) - RTX not in use, due to not supported by the XTU-C and XTU-R
6. invalidValue(-1) - Invalid valuero Adsl2StatusRtxUsed .1.3.6.1.4.1.2011.6.138.1.1.1.1.7 |
hwadsl2LineStatusLastRetrainInfoIndicates the last retrained information performed on the line.
Options:
1. none(1) - No record is available
2. cpe-l3-trigger(2) - The terminal initiates a low power consumption L3 request
3. lom-us-trigger-dra(3) - The upstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment
4. lom-ds-trigger-dra(4) - The downstream noise margin is smaller than the minimum noise margin in rate dynamic adjustment
5. cpe-never-answer-oam(5) - No OAM response is received from the CPE all the time
6. cpe-no-more-answer-oam(6) - No OAM response is received from the CPE
7. persistent-ncd-us(7) - Upstream continuous no cell delineation
8. persistent-ncd-ds(8) - Downstream continuous no cell delineation
9. persistent-lcd-us(9) - Upstream continuous loss of cell delineation
10.persistent-lcd-ds(10) - Downstream continuous loss of cell delineation
11.l2-problem-co-drop(11) - The CO is faulty during the switching from L0 to L2
12.l2-problem-cpe-drop(12) - The CPE is faulty during the switching from L0 to L2
13.bitswap-refused-us-co-drop(13) - The CO goes offline when the upstream bit swap fault occurs 10 times consecutively
14.bitswap-refused-us-cpe-drop(14) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively
15.channel-change-us-co-drop(15) - The CO goes offline when the upstream net rate changes
16.channel-change-us-cpe-drop(16) - The CPE goes offline when the upstream net rate changes
17.noise-increase-us-co-drop(17) - The CO goes offline when the upstream noise increases
18.noise-increase-us-cpe-drop(18) - The CPE goes offline when the upstream noise increases
19.bitswap-refused-ds-co-drop(19) - The CO goes offline when the downstream bit swap fault occurs 10 times consecutively
20.bitswap-refused-ds-cpe-drop(20) - The CPE goes offline when the downstream bit swap fault occurs 10 times consecutively
21.channel-change-ds-co-drop(21) - The CO goes offline when the downstream net rate changes
22.channel-change-ds-cpe-drop(22) - The CPE goes offline when the downstream net rate changes
23.noise-increase-ds-co-drop(23) - The CO goes offline when the downstream noise increases
24.noise-increase-ds-cpe-drop(24) - The CPE goes offline when the downstream noise increases
25.lom-us-co-drop(25) - The CO goes offline when the upstream noise margin is smaller than the minimum noise margin
26.lom-us-cpe-drop(26) - The CPE goes offline when the upstream noise margin is smaller than the minimum noise margin
27.lom-ds-co-drop(27) - The CO goes offline when the downstream noise margin is smaller than the minimum noise margin
28.lom-ds-cpe-drop(28) - The CPE goes offline when the downstream noise margin is smaller than the minimum noise margin
29.sra-problem-us-co-drop(29) - The CO goes offline when the upstream SRA is faulty
30.sra-problem-us-cpe-drop(30) - The CPE goes offline when the upstream SRA is faulty
31.sra-failed-us-co-drop(31) - The CO goes offline when the upstream SRA fails
32.sra-failed-us-cpe-drop(32) - The CPE goes offline when the upstream SRA fails
33.sra-problem-ds-co-drop(33) - The CO goes offline when the downstream SRA is fault
34.sra-problem-ds-cpe-drop(34) - The CPE goes offline when the downstream SRA is faulty
35.sra-rejected-ds-co-drop(35) - The CO goes offline when the downstream SRA is rejected
36.sra-rejected-ds-cpe-drop(36) - The CPE goes offline when the downstream SRA is rejected
37.bitswap-problem-us-co-drop(37) - The CO goes offline when the upstream bit swap is faulty
38.bitswap-problem-us-cpe-drop(38) - The CPE goes offline when the upstream bit swap is faulty
39.bitswap-failed-us-co-drop(39) - The CO goes offline when the upstream bit swap fails
40.bitswap-failed-us-cpe-drop(40) - The CPE goes offline when the upstream bit swap fails
41.bitswap-problem-ds-co-drop(41) - The CO goes offline when the downstream bit swap is faulty
42.bitswap-problem-ds-cpe-drop(42) - The CPE goes offline when the downstream bit swap is faulty
43.bitswap-rejected-ds-co-drop(43) - The CO goes offline when the downstream bit swap is rejected
44.bitswap-rejected-ds-cpe-drop(44) - The CPE goes offline when the downstream bit swap is rejected
45.cpe-switched-off(45) - The CPE power supply is shut down
46.cpe-lost(46) - The CPE is disconnected
47.co-reset(47) - The CO resets the chipset or line
48.co-stop(48) - The CO actively deactivate the port
49.unknown(49) - Unknown reasonro Enumeration .1.3.6.1.4.1.2011.6.138.1.1.1.1.8 |
hwadsl2LineStatusLineRateDsThe actual line rate downstream.
Unit: bits/secondro Unsigned32 UNITS "bits/second" .1.3.6.1.4.1.2011.6.138.1.1.1.1.9 |
hwadsl2LineStatusLineRateUsThe actual line rate upstream.
Unit: bits/secondro Unsigned32 UNITS "bits/second" .1.3.6.1.4.1.2011.6.138.1.1.1.1.10 |
hwadsl2Status OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.2 |
hwadsl2ChannelStatusTableThe table hwadsl2ChannelStatusTable contains status
parameters of the ADSL2 channel and live data from equipment.
The indexes of this table are ifIndex and adsl2ChStatusUnit. SEQUENCE OF Hwadsl2ChannelStatusEntry .1.3.6.1.4.1.2011.6.138.1.2.1 |
hwadsl2ChannelStatusEntryThe table hwadsl2ChannelStatusTable contains status
parameters of the ADSL2 channel and live data from equipment.
The indexes of this entry are ifIndex and adsl2ChStatusUnit. Hwadsl2ChannelStatusEntry .1.3.6.1.4.1.2011.6.138.1.2.1.1 |
hwadsl2ChStatusPhyRrrcBitsThe bits in the channel that used to retransmission.
Unit: bitro Counter32 UNITS "bit" .1.3.6.1.4.1.2011.6.138.1.2.1.1.1 |
hwadsl2ChStatusPhyRtxQueueThe number of the units for retransmission.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.2 |
hwadsl2ChStatusINPIf retransmission is not used in a given transmit direction, this
parameter reports the actual impulse noise protection (INP) on the
bearer channel in the L0 state. In the L1 or L2 state, the parameter
contains the INP in the previous L0 state.
If retransmission is used in a given transmit direction, this parameter
reports the actual impulse noise protection (INP) against SHINE on
the bearer channel in the L0 state. In the L2 state, the parameter
contains the INP in the previous L0 state.
Unit: 0.1 DMT symbolro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.3 |
hwadsl2ChStatusRSRedundancyThe actual number of Reed-Solomon redundancy
bytes per codeword used in the latency path
in which the bearer channel is transported.
The value is coded in bytes.
The value 0 indicates no Reed-Solomon coding.
Unit: bytero Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.4 |
hwadsl2ChStatusRSSymbolsThe DMT Symbol number per codeword used in
the latency path in which the bearer channel
is transported.
Unit: 0.01 DMT symbolro Unsigned32 UNITS "0.01 DMT symbol" .1.3.6.1.4.1.2011.6.138.1.2.1.1.5 |
hwadsl2ChStatusInterDepthThe actual Reed-Solomon codeword size used
in the latency path in which the bearer channel
is transported.
The value ranges from 1 to 4096 by step of 1.
The value 1 indicates no interleaving.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.6 |
hwadsl2ChStatusSymbolLengthThe actual number of bits per symbol assigned
to the latency path in which the bearer channel
is transported.
This value does not include trellis overhead.
Unit: bitro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.7 |
hwadsl2ChStatusRSSizeThe actual Reed-Solomon codeword size used
in the latency path in which the bearer channel
is transported.
Unit: bytero Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.8 |
hwadsl2ChStatusActNetDataRateIn L0 state, this parameter reports the Net Data Rate at which the bearer channel is operating.
In L2 state, this parameter contains the Net Data Rate in the previous L0 state.
This parameter is optional if G.998.4 retransmission function is not supported.
The data rate is coded in steps of 1000 bit/s.ro Unsigned32 UNITS "bits/second" .1.3.6.1.4.1.2011.6.138.1.2.1.1.9 |
hwadsl2ChStatusActINPAgainstREINIf retransmission is used in a given transmit direction,
this parameter reports the actual impulse noise protection (INP)
against REIN (under specific conditions detailed in G.998.4)
on the bearer channel in the L0 state. In the L2 state, the
parameter contains the INP in the previous L0 state. The value
is coded in fractions of DMT symbols with a granularity of 0.1 symbols.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.2.1.1.10 |
hwadsl2SCStatusTableThe table hwadsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers. The following points apply to this
table:
1. The main purpose of this table is to hold the results
of a DELT.
2. This table also holds parameters obtained at line
initialization time.
3. The rows in this table are volatile; that is, they are
lost if the SNMP agent is rebooted.
4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are
very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager
may delete rows in this table.
6. The maximum number of rows allowable in this table is
indicated by the scalar attribute
adsl2ScalarSCMaxInterfaces.
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT completes successfully or when line
initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes, and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successful.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows:
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT is started on the above-mentioned
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT completes, and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
The indexes of this table are ifIndex and adsl2SCStatusDirection. SEQUENCE OF Hwadsl2SCStatusEntry .1.3.6.1.4.1.2011.6.138.1.2.2 |
hwadsl2SCStatusEntryThe table hwadsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers. The following points apply to this
table:
1. The main purpose of this table is to hold the results
of a DELT.
2. This table also holds parameters obtained at line
initialization time.
3. The rows in this table are volatile; that is, they are
lost if the SNMP agent is rebooted.
4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are
very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager
may delete rows in this table.
6. The maximum number of rows allowable in this table is
indicated by the scalar attribute
adsl2ScalarSCMaxInterfaces.
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT completes successfully or when line
initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes, and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successful.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows:
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT is started on the above-mentioned
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT completes, and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
The indexes of this entry are ifIndex and adsl2SCStatusDirection. Hwadsl2SCStatusEntry .1.3.6.1.4.1.2011.6.138.1.2.2.1 |
hwadsl2SCStatusInfoTxPSDThe PSD MASK per sub-carrier.An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-carriers.
It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values
are -140 to -30 dBm/Hz).
Unit: 0.1 dBm/Hzro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.2.2.1.1 |
hwadsl2SCStatusInfoSnrMarginsSNR Margin is the maximum increase in dB of the noise power
received at the ATU (ATU-R on downstream direction and ATU-C
on upstream direction), such that the BER requirements are met
for all bearer channels received at the ATU. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to 63 dB).
Unit: 0.1 dBro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.2.2.1.2 |
hwadsl2Inventory OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.3 |
hwadsl2PM OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.4 |
hwadsl2PMLine OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.4.1 |
hwadsl2PMLineCurrTableThe table hwadsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this table are ifIndex and adsl2PMLCurrUnit. SEQUENCE OF Hwadsl2PMLineCurrEntry .1.3.6.1.4.1.2011.6.138.1.4.1.1 |
hwadsl2PMLineCurrEntryThe table hwadsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 line.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this entry are ifIndex and adsl2PMLCurrUnit. Hwadsl2PMLineCurrEntry .1.3.6.1.4.1.2011.6.138.1.4.1.1.1 |
hwadsl2PMLCurr15MInmainpeqThis parameter is a count of the INMAINPEQi anomalies
occurring on the line during current 15 minutes.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.1 |
hwadsl2PMLCurr15MInmameThis parameter is a count of the INMAME anomalies
occurring on the line during current 15 minutes.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.2 |
hwadsl2PMLCurr15MInmaiatThis parameter is a count of the INMAIATi anomalies
occurring on the line during current 15 minutes.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.3 |
hwadsl2PMLCurr1DayInmainpeqThis parameter is a count of the INMAINPEQi anomalies
occurring on the line during current 1 day.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.4 |
hwadsl2PMLCurr1DayInmameThis parameter is a count of the INMAME anomalies
occurring on the line during current 1 day.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.5 |
hwadsl2PMLCurr1DayInmaiatThis parameter is a count of the INMAIATi anomalies
occurring on the line during current 1 day.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.6 |
hwadsl2PMLEverBeforeInmainpeqThis parameter is a count of the INMAINPEQi anomalies
occurring on the line ever before.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.7 |
hwadsl2PMLEverBeforeInmameThis parameter is a count of the INMAME anomalies
occurring on the line ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.8 |
hwadsl2PMLEverBeforeInmaiatThis parameter is a count of the INMAIATi anomalies
occurring on the line ever before.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.9 |
hwadsl2PMLEverBeforeFecsCount of seconds since agent reset that there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.10 |
hwadsl2PMLEverBeforeEsCount of seconds since agent reset that there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.11 |
hwadsl2PMLEverBeforeSesCount of seconds since agent reset that there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.12 |
hwadsl2PMLEverBeforeLossCount of seconds since agent reset that there was LOS (or
LOS-FE for ATU-R).
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.13 |
hwadsl2PMLEverBeforeUasCount of seconds in Unavailability State since agent reset.
Unavailability begins at the onset of 10 contiguous severely
-errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.14 |
hwadsl2PMLCurr15MStartTimeStart time of the current 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.15 |
hwadsl2PMLCurr1DayStartTimeStart time of the current 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.16 |
hwadsl2PMLCurr15MLofsCount of seconds in the current 15 minute interval when there was Loss of Framing.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.17 |
hwadsl2PMLCurr15MLolsCount of seconds in the current 15 minute interval when there was Loss of Link.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.18 |
hwadsl2PMLCurr15MLopsCount of seconds in the current 15 minute interval when there was Loss of Power.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.19 |
hwadsl2PMLCurr1DayLofsCount of the number of seconds when there was Loss of Framing during the current day.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.20 |
hwadsl2PMLCurr1DayLolsCount of the number of seconds when there was Loss of Link during the current day.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.21 |
hwadsl2PMLCurr1DayLopsCount of the number of seconds when there was Loss of Power during the current day.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.22 |
hwadsl2PMLEverBeforeLofsCount of the number of seconds when there was Loss of Framing since agent reset.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.23 |
hwadsl2PMLEverBeforeLolsCount of the number of seconds when there was Loss of Link since agent reset.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.24 |
hwadsl2PMLEverBeforeLopsCount of the number of seconds when there was Loss of Power since agent reset.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.25 |
hwadsl2PMLCurr15MLeftrsIf retransmission is used in a given transmit direction, this parameter
is a count of the seconds with a near-end leftr defect present observed
over the 15 minutes accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.26 |
hwadsl2PMLCurr15MEfbIf retransmission is used in a given transmit direction, this parameter
is a count of the number of error-free bits observed over the 15 minutes
accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.27 |
hwadsl2PMLCurr15MMinEftrIf retransmission is used in a given transmit direction, this parameter
reports the minimum of the EFTR(Error-free throughput rate) observed
over the 15 minutes accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.28 |
hwadsl2PMLCurr1DayLeftrsIf retransmission is used in a given transmit direction, this parameter
is a count of the seconds with a near-end leftr defect present observed
over the 24 hours accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.29 |
hwadsl2PMLCurr1DayEfbIf retransmission is used in a given transmit direction, this parameter
is a count of the number of error-free bits observed over the 24 hours
accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.30 |
hwadsl2PMLCurr1DayMinEftrIf retransmission is used in a given transmit direction, this parameter
reports the minimum of the EFTR(Error-free throughput rate) observed
over the 24 hours accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.31 |
hwadsl2PMLEverBeforeLeftrsIf retransmission is used in a given transmit direction, this parameter
is a count of the seconds with a near-end leftr defect present observed
ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.32 |
hwadsl2PMLEverBeforeEfbIf retransmission is used in a given transmit direction, this parameter
is a count of the number of error-free bits observed ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.33 |
hwadsl2PMLEverBeforeMinEftrIf retransmission is used in a given transmit direction, this parameter
reports the minimum of the EFTR(Error-free throughput rate) observed
ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.1.1.34 |
hwadsl2PMLineHist15MinTableThe table hwadsl2PMLineHist15MinTable contains Performance
Monitoring results of ADSL2 line at last 15 minutes.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this table are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval. SEQUENCE OF Hwadsl2PMLineHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.1.2 |
hwadsl2PMLineHist15MinEntryThe table hwadsl2PMLineHist15MinTable contains Performance
Monitoring results of ADSL2 line at last 15 minutes.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this entry are ifIndex, adsl2PMLHist15MUnit and adsl2PMLHist15MInterval. Hwadsl2PMLineHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.1.2.1 |
hwadsl2PMLHist15MInmainpeqThis parameter is a count of the INMAINPEQi anomalies
occurring on the line at last 15 minutes.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.1 |
hwadsl2PMLHist15MInmameThis parameter is a count of the INMAME anomalies
occurring on the line at last 15 minutes.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.2 |
hwadsl2PMLHist15MInmaiatThis parameter is a count of the INMAIATi anomalies
occurring on the line at last 15 minutes.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.3 |
hwadsl2PMLHist15MStartTimeStart time of the historical 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.4 |
hwadsl2PMLHist15MLofsCount of seconds in the interval when there was Loss of Framing.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.5 |
hwadsl2PMLHist15MLolsCount of seconds in the interval when there was Loss of Link.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.6 |
hwadsl2PMLHist15MLopsCount of seconds in the interval when there was Loss of Power.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.7 |
hwadsl2PMLHist15MLeftrsIf retransmission is used in a given transmit direction, this parameter
is a count of the seconds with a near-end leftr defect present observed
over the 15 minutes accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.8 |
hwadsl2PMLHist15MEfbIf retransmission is used in a given transmit direction, this parameter
is a count of the number of error-free bits observed over the 15 minutes
accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.9 |
hwadsl2PMLHist15MMinEftrIf retransmission is used in a given transmit direction, this parameter
reports the minimum of the EFTR(Error-free throughput rate) observed
over the 15 minutes accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.2.1.10 |
hwadsl2PMLineHist1DayTableThe table hwadsl2PMLineHist1DayTable contains Performance
Monitoring results of ADSL2 line at last 1 day.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this table are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval. SEQUENCE OF Hwadsl2PMLineHist1DayEntry .1.3.6.1.4.1.2011.6.138.1.4.1.3 |
hwadsl2PMLineHist1DayEntryThe table hwadsl2PMLineHist1DayTable contains Performance
Monitoring results of ADSL2 line at last 1 day.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this entry are ifIndex, adsl2PMLHist1DUnit and adsl2PMLHist1DInterval. Hwadsl2PMLineHist1DayEntry .1.3.6.1.4.1.2011.6.138.1.4.1.3.1 |
hwadsl2PMLHist1DayInmainpeqThis parameter is a count of the INMAINPEQi anomalies
occurring on the line at last 1 day.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.1 |
hwadsl2PMLHist1DayInmameThis parameter is a count of the INMAME anomalies
occurring on the line at last 1 day.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.2 |
hwadsl2PMLHist1DayInmaiatThis parameter is a count of the INMAIATi anomalies
occurring on the line at last 1 day.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.3 |
hwadsl2PMLHist1DayStartTimeStart time of the historical 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.4 |
hwadsl2PMLHist1DayLofsCount of seconds during this interval that there was Loss of Framing.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.5 |
hwadsl2PMLHist1DayLolsCount of seconds during this interval that there was Loss of Link.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.6 |
hwadsl2PMLHist1DayLopsCount of seconds during this interval that there was Loss of Power.
Unit: secondsro Counter32 UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.7 |
hwadsl2PMLHist1DLeftrsIf retransmission is used in a given transmit direction, this parameter
is a count of the seconds with a near-end leftr defect present observed
over the 24 hours accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.8 |
hwadsl2PMLHist1DEfbIf retransmission is used in a given transmit direction, this parameter
is a count of the number of error-free bits observed over the 24 hours
accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.9 |
hwadsl2PMLHist1DMinEftrIf retransmission is used in a given transmit direction, this parameter
reports the minimum of the EFTR(Error-free throughput rate) observed
over the 24 hours accumulation period.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.1.3.1.10 |
hwadsl2PMLineCurrInitTableThe table hwadsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized.
The index of this table is ifIndex. SEQUENCE OF Hwadsl2PMLineCurrInitEntry .1.3.6.1.4.1.2011.6.138.1.4.1.4 |
hwadsl2PMLineCurrInitEntryThe table hwadsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized.
The index of this entry is ifIndex. Hwadsl2PMLineCurrInitEntry .1.3.6.1.4.1.2011.6.138.1.4.1.4.1 |
hwadsl2PMLInitEverBeforeFullInitsCount of full initializations attempted on the line
(successful and failed) since agent reset.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.1 |
hwadsl2PMLInitEverBeforeFailedFullInitsCount of failed full initializations on the line since agent
reset.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.2 |
hwadsl2PMLInitEverBeforeShortInitsCount of short initializations attempted on the line
(successful and failed) since agent reset.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.3 |
hwadsl2PMLInitEverBeforeFailedShortInitsCount of failed short initializations on the line since agent
reset.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.4 |
hwadsl2PMLineCurrInit15MStartTimeStart time of the current init 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.5 |
hwadsl2PMLineCurrInit1DayStartTimeStart time of the current init 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.4.1.6 |
hwadsl2PMLineInitHist15MinTableThe table hwadsl2PMLineInitHist15MinTable contains Performance
Monitoring results of ADSL2 line initialize at last 15 minutes.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this table are ifIndex and adsl2PMLHistInit15MInterval. SEQUENCE OF Hwadsl2PMLineInitHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.1.5 |
hwadsl2PMLineInitHist15MinEntryThe table hwadsl2PMLineInitHist15MinTable contains Performance
Monitoring results of ADSL2 line initialize at last 15 minutes.
The PM counters in the table are not reset even when the xtU
is reinitialized. They are re-initialized only when the
agent itself is reset or reinitialized.
The indexes of this entry are ifIndex and adsl2PMLHistInit15MInterval. Hwadsl2PMLineInitHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.1.5.1 |
hwadsl2PMLineInitHist15MinStartTimeStart time of the historical init 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.5.1.1 |
hwadsl2PMLineInitHist1DayTableThe table hwadsl2PMLineInitHist1DayTable contains Performance
Monitoring results of ADSL2 line initialize at last one day.
The indexes of this table are ifIndex and adsl2PMLHistinit1DInterval. SEQUENCE OF Hwadsl2PMLineInitHist1DayEntry .1.3.6.1.4.1.2011.6.138.1.4.1.6 |
hwadsl2PMLineInitHist1DayEntryThe table hwadsl2PMLineInitHist1DayTable contains Performance
Monitoring results of ADSL2 line initialize at last one day.
The indexes of this entry are ifIndex and adsl2PMLHistinit1DInterval. Hwadsl2PMLineInitHist1DayEntry .1.3.6.1.4.1.2011.6.138.1.4.1.6.1 |
hwadsl2PMLineInitHist1DayStartTimeStart time of the historical init 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.1.6.1.1 |
hwadsl2PMChannel OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.4.2 |
hwadsl2PMChCurrTableThe table hwadsl2PMChCurrTable contains some extended current
Performance Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized.
The indexes of this table are ifIndex and adsl2PMChCurrUnit. SEQUENCE OF Hwadsl2PMChCurrEntry .1.3.6.1.4.1.2011.6.138.1.4.2.1 |
hwadsl2PMChCurrEntryThe table hwadsl2PMChCurrTable contains some extended current
Performance Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized.
The indexes of this entry are ifIndex and adsl2PMChCurrUnit. Hwadsl2PMChCurrEntry .1.3.6.1.4.1.2011.6.138.1.4.2.1.1 |
hwadsl2PMChCurr15MRtxCWCount of units request retransmission on this
channel within the current 15 minute interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.1 |
hwadsl2PMChCurr15MRtxCorrectedCWCount of units corrected by retransmission on this
channel within the current 15 minute interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.2 |
hwadsl2PMChCurr15MRtxUncorrectedCWCount of units uncorrected by retransmission on
this channel within the current 15 minute interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.3 |
hwadsl2PMChCurr1DayRtxCWCount of units request retransmission on
this channel during the current day.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.4 |
hwadsl2PMChCurr1DayRtxCorrectedCWCount of units corrected by retransmission
on this channel during the current day.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.5 |
hwadsl2PMChCurr1DayRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel during the current day.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.6 |
hwadsl2PMChEverBeforeRtxCWCount of units request retransmission on
this channel ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.7 |
hwadsl2PMChEverBeforeRtxCorrectedCWCount of units corrected by retransmission
on this channel ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.8 |
hwadsl2PMChEverBeforeRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel ever before.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.9 |
hwadsl2PMChEverBeforeCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel since agent reset. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.10 |
hwadsl2PMChEverBeforeCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel since agent reset. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels.ro Unsigned32 .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.11 |
hwadsl2PMChCur15MStartTimeStart time of the channel current 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.12 |
hwadsl2PMChCur1DayStartTimeStart time of the channel current 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.2.1.1.13 |
hwadsl2PMChHist15MinTableThe table hwadsl2PMChHist15MinTable contains PM channel history
for 15min intervals of the ADSL2 channel.
The indexes of this table are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval. SEQUENCE OF Hwadsl2PMChHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.2.2 |
hwadsl2PMChHist15MinEntryThe table hwadsl2PMChHist15MinTable contains PM channel history
for 15min intervals of the ADSL2 channel.
The indexes of this entry are ifIndex,adsl2PMChHist15MUnit and adsl2PMChHist15MInterval. Hwadsl2PMChHist15MinEntry .1.3.6.1.4.1.2011.6.138.1.4.2.2.1 |
hwadsl2PMChHist15MRtxCWCount of units request retransmission on
this channel within the last 15 minutes interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.2.1.1 |
hwadsl2PMChHist15MRtxCorrectedCWCount of units corrected by retransmission
on this channel within the last 15 minutes interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.2.1.2 |
hwadsl2PMChHist15MRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel within the last 15 minutes interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.2.1.3 |
hwadsl2PMChHist15MStartTimeStart time of the historical 15-minute performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.2.2.1.4 |
hwadsl2PMChHist1DTableThe table hwadsl2PMChHist1DayTable contains some extended PM
channel history for 1-day intervals of ADSL2.
The indexes of this table are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval. SEQUENCE OF Hwadsl2PMChHist1DEntry .1.3.6.1.4.1.2011.6.138.1.4.2.3 |
hwadsl2PMChHist1DEntryThe table hwadsl2PMChHist1DayTable contains some extended PM
channel history for 1-day intervals of ADSL2.
The indexes of this entry are ifIndex,adsl2PMChHist1DUnit and adsl2PMChHist1DInterval. Hwadsl2PMChHist1DEntry .1.3.6.1.4.1.2011.6.138.1.4.2.3.1 |
hwadsl2PMChHist1DRtxCWCount of units request retransmission on
this channel within the last 1 day interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.3.1.1 |
hwadsl2PMChHist1DRtxCorrectedCWCount of units corrected by retransmission
on this channel within the last 1 day interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.3.1.2 |
hwadsl2PMChHist1DRtxUncorrectedCWCount of units uncorrected by retransmission
on this channel within the last 1 day interval.ro Counter32 .1.3.6.1.4.1.2011.6.138.1.4.2.3.1.3 |
hwadsl2PMChHist1DStartTimeStart time of the historical 1-day performance statistics.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.138.1.4.2.3.1.4 |
hwadsl2Profile OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.5 |
hwadsl2ProfileLine OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.5.1 |
hwadsl2LineConfProfTableThe table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile
configuration.Entries in this table MUST be maintained in a persistent manner.
The index of this table is adsl2LConfProfProfileName. SEQUENCE OF Hwadsl2LineConfProfEntry .1.3.6.1.4.1.2011.6.138.1.5.1.2 |
hwadsl2LineConfProfEntryThe table hwadsl2LineConfProfTable contains huawei private ADSL2 line profile
configuration.Entries in this table MUST be maintained in a persistent manner.
The index of this entry is adsl2LConfProfProfileName. Hwadsl2LineConfProfEntry .1.3.6.1.4.1.2011.6.138.1.5.1.2.1 |
hwadsl2LConfProfInmIatoDsThe parameter of downstream impulse noise monitoring inter arrival time offset.
This is the Inter Arrival Time Offset that the xTU receiver shall use to determine
in which bin of the Inter Arrival Time histogram the IAT is reported.
The valid values for INMIATO ranges from 3 to 511 DMT symbols in steps of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.1 |
hwadsl2LConfProfInmIatsDsThe parameter of downstream impulse noise monitoring inter arrival time step.
This is the Inter Arrival Time Step that the xTU receiver shall use to determine
in which bin of the Inter Arrival Time histogram the IAT is reported.
The valid values for INMIATS ranges from 0 to 7 in steps of 1.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.2 |
hwadsl2LConfProfInmCcDsThe parameter of Downstream impulse noise monitoring cluster continuation value.
This is the Cluster Continuation value that the xTU receiver shall use
in the cluster indication process described in the relevant ITU-T Recommendation.
The valid values for INMCC range from 0 to 64 DMT symbols in steps of 1 DMT symbol.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.3 |
hwadsl2LConfProfInmInpeqModeDsThe parameter of Downstream impulse noise monitoring equivalent impulse noise protect mode.
This is the INM Equivalent INP Mode that the xTU receiver shall use in the computation of the Equivalent INP,
as defined in the relevant ITU-T Recommendation. The valid values for INM_INPEQ_MODE are 0, 1, 2, 3, and 4.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.4 |
hwadsl2LConfProfRfiBandsThe RFI notch parameter.
It is a string consist of begin tone index,
end tone index and psd value.
This is a string of 4 groups of values in the following
structure:
Octets 0+1 - Index of start sub-carrier used in the context
of a first group
Octets 2+3 - Index of end sub-carrier used in the context
of a first group
Octet 4+5 - The psd value configurated in the first group
Octets 6-11 - Same, for a 2nd group
This architecture continues until octets 22-23, which are
associated with a 4th group.It can contain as most as 4 groups.rw Adsl2RfiBand .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.5 |
hwadsl2LConfProfReferenceClockThis object configures the clock reference for the ATU-C
in an ADSL Line.rw Adsl2LConfProfReferenceClockType .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.6 |
hwadsl2LConfProfL3TimeThis minimum time (in seconds) between an Entry into the
L3 state and the L0 or L2 state.
Unit: secondsrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.7 |
hwadsl2LConfProfDpboEselMinDPBOESELMIN in dB is the minimum of all main cable losses for the KVz supplied when using
the SOL model (expansion of a KVz and ADSL2 provision of additional KVz areas from this KVz
using cross-cables to additional KVz), including the KVz at the MSAN site. This value must
be adjustable as the minimum requirement via the SNMP interface in the configuration profile
for each ADSL2 port, and is set individually for each MSAN site and usage. As an option,
adjustment can be done for each MSAN or line card, thus taking effect for
entire port groups. It is used only for determining the MUF.
Unit: 0.5dBrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.8 |
hwadsl2LConfProfTrellisModeEnables and disables the trellis mode. This
object is defaulted enabled(2).rw Adsl2TrellisMode .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.9 |
hwadsl2LConfProfBitSwapDsEnables and disables the bit swap downstream of a line.rw Adsl2BitSwap .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.10 |
hwadsl2LConfProfBitSwapUsEnables and disables the bit swap upstream of a line.rw Adsl2BitSwap .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.11 |
hwadsl2LConfProfDpboEPsdThis parameter defines the PSD mask that is assumed to be permitted at the exchange.
This parameter shall use the same format as PSDMASKds.The maximum number of breakpoints
for DPBOEPSD is 16.
This is a string of 16 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1
Octets 3-5 - Same, for a 2nd breakpoint
Octets 6-8 - Same, for a 3rd breakpoint
This architecture continues until octets 45-47, which are
associated with a 16th breakpoint.
Each subcarrier index is an unsigned number in the range 1 and
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 16, all remaining
octets are set to the value 0xff.rw Adsl2DpboEpsd .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.12 |
hwadsl2LConfProfDpboEsELThis configuration parameter defines the assumed electrical length of
cables (E-side cables) connecting exchange based DSL services to a remote
flexibility point (cabinet), that hosts the xTU-C that is subject to
spectrally shaped downstream power back-off depending on this length.
For this parameter the electrical length is defined as the loss (in dB)
of an equivalent length of hypothetical cable at a reference frequency
defined by the network operator or in spectrum management regulations.
DPBOESEL shall be coded as an unsigned integer representing an electrical
length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB.
All values in the range are valid.If DPBOESEL is set to zero, the DPBO in
this section shall be disabled.
Unit: 0.5dBrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.13 |
hwadsl2LConfProfDpboEsCableModelAThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.14 |
hwadsl2LConfProfDpboEsCableModelBThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.15 |
hwadsl2LConfProfDpboEsCableModelCThis configuration parameter defines a cable model in terms of three scalars
DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency
dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be
coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5
(coded as 640) in step of 1/256. All values in the range are valid.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.16 |
hwadsl2LConfProfDpboMusDPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for
exchange based services, used to modify parameter DPBOFMAX defined below. It
shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz
(coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz.
All values in the range are valid.
Unit: 0.5dBm/Hzrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.17 |
hwadsl2LConfProfDpboFMinDPBOFMIN defines the minimum frequency from which the DPBO shall be applied.
It shall be coded as a 16 bits unsigned integer representing a frequency in
multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0)
to 8832 kHz (coded as 2048).
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.18 |
hwadsl2LConfProfDpboFMaxDPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be
coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz.
The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956).
Unit: 4.3125 KHzrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.1.2.1.19 |
hwadsl2ProfileChannel OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.5.2 |
hwadsl2ChConfProfileTableThe table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel
profile configuration.
Entries in this table MUST be maintained in a persistent manner.
The index of this table is adsl2ChConfProfProfileName. SEQUENCE OF Hwadsl2ChConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.2.1 |
hwadsl2ChConfProfileEntryThe table hwadsl2ChConfProfileTable contains huawei private ADSL2 channel
profile configuration.
Entries in this table MUST be maintained in a persistent manner.
The index of this entry is adsl2ChConfProfProfileName. Hwadsl2ChConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.2.1.1 |
hwadsl2ChConfProfDataPathModeThe channel data path mode.
Options:
1. atm(1) - ATM data path
2. ptm(2) - PTM data path
3. both(3) - ATM and PTM data path
Huawei defined.rw Adsl2DataPathMode .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.1 |
hwadsl2ChConfProfErasureDecodingEnable or disable the erasure decoding of a channel.
Options:
1. enable(1) - Open the erasure decoding of a channel
2. disable(2) - Close the erasure decoding of a channelrw Adsl2ProfSwitchType .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.2 |
hwadsl2ChConfProfPhyRcontrolDsTo enable or disable the retransmission function of downstream PHY-R.
Options:
1. enable(1) - Enable the retransmission function of downstream PHY-R
2. disable(2) - Disable the retransmission function of downstream PHY-Rrw Adsl2PhyRControl .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.3 |
hwadsl2ChConfProfPhyRcontrolUsTo enable or disable the retransmission function of upstream PHY-R.
Options:
1. enable(1) - Enable the retransmission function of upstream PHY-R
2. disable(2) - Disable the retransmission function of upstream PHY-Rrw Adsl2PhyRControl .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.4 |
hwadsl2ChConfProfInpMaxDsMaximum Impulse Noise Protection on downstream direction.rw Adsl2SymbolProtection .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.5 |
hwadsl2ChConfProfInpMaxUsMaximum Impulse Noise Protection on upstream direction.rw Adsl2SymbolProtection .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.6 |
hwadsl2ChConfProfMinRtxRatioDsThis object is used to config the minimum retransmission band width parameter downstream.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.7 |
hwadsl2ChConfProfMinRtxRatioUsThis object is used to config the minimum retransmission band width parameter upstream.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.8 |
hwadsl2ChConfProfMinRSoverheadDsThis object is used to config the minimum RSoverhead parameter downstream.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.9 |
hwadsl2ChConfProfMinRSoverheadUsThis object is used to config the minimum RSoverhead parameter upstream.rw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.2.1.1.10 |
hwadsl2ProfileAlarmConf OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.5.3 |
hwadsl2ChAlarmConfProfileTableThe table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles.
Entries in this table MUST be maintained in a persistent manner.
The index of this table is adsl2ChAlarmConfProfileName. SEQUENCE OF Hwadsl2ChAlarmConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.3.1 |
hwadsl2ChAlarmConfProfileEntryThe table hwadsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles.
Entries in this table MUST be maintained in a persistent manner.
The index of this entry is adsl2ChAlarmConfProfileName. Hwadsl2ChAlarmConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.3.1.1 |
hwadsl2ChAlarmConfProfileMonitoringRateDsThe channel monitoring rate downstream.
When the value you set is larger than
the value of the rate downstream defined in the channel
profile, it will not be successful. The value 0 means
that no threshold is specified for the associated
counter.
Unit: bits/secondrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.3.1.1.1 |
hwadsl2ChAlarmConfProfileMonitoringRateUsThe channel monitoring rate upstream.
When the value you set is larger than
the value of the rate upstream defined in the channel
profile, it will not be successful. The value 0 means
that no threshold is specified for the associated
counter.
Unit: bits/secondrw Unsigned32 .1.3.6.1.4.1.2011.6.138.1.5.3.1.1.2 |
hwadsl2LineAlarmConfProfileTableThe table hwadsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document.
The index of this table is adsl2LineAlarmConfProfileName. SEQUENCE OF Hwadsl2LineAlarmConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.3.2 |
hwadsl2LineAlarmConfProfileEntryThe table hwadsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document.
The index of this entry is adsl2LineAlarmConfProfileName. Hwadsl2LineAlarmConfProfileEntry .1.3.6.1.4.1.2011.6.138.1.5.3.2.1 |
hwadsl2LineAlarmConfProfileXturThresh15MinLeftrsA threshold for the hwadsl2PMLCurr15MLeftrs counter,
when adsl2PMLCurrUnit is ATUR {2}.
The value 0 means that no threshold is specified for the
associated counter.
Unit: secondsrw HCPerfIntervalThreshold UNITS "seconds" .1.3.6.1.4.1.2011.6.138.1.5.3.2.1.1 |
hwAdsl2LineAlarmConfProfileDyingGaspAlarmSwitchThis object enable/disable the report of LOSS-OF-POWER
alarm in an ADSL line.
Options:
1. enable(1) - The report of LOSS-OF-POWER alarm in an ADSL line is enabled
2. disable(2) - The report of LOSS-OF-POWER alarm in an ADSL line is disabledrw Enumeration .1.3.6.1.4.1.2011.6.138.1.5.3.2.1.2 |
hwAdsl2LineAlarmConfProfileActiveFailAlarmSwitchThis object enable/disable the active fail alarm switch.
Options:
1. enable(1) - The active fail alarm switch is enabled
2. disable(2) - The active fail alarm switch is disabledrw Enumeration .1.3.6.1.4.1.2011.6.138.1.5.3.2.1.3 |
hwadsl2Scalar OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.6 |
hwadsl2ScalarSC OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.6.1 |
hwadsl2Conformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.8 |
hwadsl2Mode OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.9 |
hwadslmodecfgCfgThis object is used to change ADSL management mode.
After the mode being changed, system will automatically
save data and reboot.rw Adsl2CfgMode .1.3.6.1.4.1.2011.6.138.1.9.1 |
hwadslabrmodecfgCfgThis object is used to change abr-calculation mode.
Options:
1. normalMode(1) - Normal abr-calculation mode
2. ptMode(2) - PT abr-calculation moderw Enumeration .1.3.6.1.4.1.2011.6.138.1.9.2 |
hwAdsl2TrapsVbOids OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.10 |
hwadsl2LinePMThresholdItemIndicate the threshold item.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.10.0 |
hwadsl2LineTemplateIDIndicate line template ID.ro Gauge32 .1.3.6.1.4.1.2011.6.138.1.10.1 |
hwadsl2ActivationFailureCauseThe reason of activation failure.ro OCTET STRING .1.3.6.1.4.1.2011.6.138.1.10.2 |
hwadsl2ChipsetIDThe Chipset ID.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.3 |
hwAdsl2SwitchResultMode switch result.
Options:
1. success(0) - Indicates that the adsl mode switch result is success
2. fail(1) - Indicates that the adsl mode switch result is failro Enumeration .1.3.6.1.4.1.2011.6.138.1.10.4 |
hwAdsl2RequestIDRequest ID.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.5 |
hwadsl2LineCmndConfLdsfResultThe result of the test.
Options:
1. success(0) - Indicates that the test result is success
2. fail(1) - Indicates that the test result is failro Enumeration .1.3.6.1.4.1.2011.6.138.1.10.6 |
hwadsl2LinePMThresholdValueIndicate the threshold value of threshold item.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.7 |
hwadsl2LinePMCurrentValueIndicate the current value of threshold item.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.8 |
hwadsl2ChPMThresholdValueIndicate the threshold value of threshold item.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.9 |
hwadsl2ChPMCurrentValueIndicate the current value of threshold item.ro Integer32 .1.3.6.1.4.1.2011.6.138.1.10.10 |
hwadsl2Traps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.11 |
hwAdsl2CommonTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.11.1 |
hwAdsl2CommonTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.11.1.0 |
hwAdsl2ModeSwitchResultTrapAdsl2 mode switch result trap.
This trap message is generated when the result of the recent ADSL mode switch process. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.1.0.1 |
hwAdsl2AdminModeTrapAdsl2 administration mode trap.
This trap message is generated when the ADSL mode is the system worked. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.1.0.2 |
hwAdsl2DeltOperResultTrapNGADSL delt trap.
This trap message is generated when delt test result reported. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.1.0.3 |
hwAdsl2PortStatusChangeTrapAdsl2 port status change trap.
This trap message is generated when port status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.1.0.4 |
hwadsl2AlarmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.11.2 |
hwadsl2AlarmTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.138.1.11.2.0 |
hwadsl2PortAutoDeactiveAlarmTrapPort automatically trap.
This trap message is generated when the ADSL port is automatically deactivated.
The ADSL port is automatically deactivated due to the line fault. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.0 |
hwAdsl2PortReactiveAlarmTrapPort reactive trap.
This trap message is generated when the ADSL port is re-activated after the
ADSL line recovers. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.1 |
hwAdsl2PortATURPowerOffAlarmTrapPort ATU-R power off trap.
This trap message is generated when ATU-R is powered off. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.2 |
hwAdsl2ChipsetRecoverAlarmTrapChipset recover trap.
This trap message is generated when the ADSL chipset recovers. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.3 |
hwAdsl2PortDeactiveAlarmTrapPort deactive trap.
This trap message is generated when some xDSL ports or all the xDSL ports are automatically deactivated.
Some xDSL ports or all the xDSL ports are automatically deactivated due to lack of licenses. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.4 |
hwAdsl2LinePerformanceStatAlarmTrapLine performance statistics trap.
This trap message is generated when the line performance statistics of the ADSL
port reach the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.5 |
hwAdsl2DownstreamActivationRateAlarmTrapADSL channel downstream activation rate trap.
This trap message is generated when the ADSL channel downstream activation rate is
lower than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.6 |
hwAdsl2ChannelPerformanceStatAlarmTrapChannel performance statistics trap.
This trap message is generated when the channel performance statistics of the ADSL
port reach the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.7 |
hwAdsl2UpstreamActivationRateAlarmTrapADSL channel upstream activation rate trap.
This trap message is generated when the ADSL channel upstream activation rate is
lower than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.8 |
hwAdsl2UpstreamRateIncreaseAlarmTrapADSL channel upstream rate increases trap.
This trap message is generated when the ADSL channel upstream rate increases to
a value higher than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.9 |
hwAdsl2UpstreamRateDecreaseAlarmTrapADSL channel upstream rate decreases trap.
This trap message is generated when the ADSL channel upstream rate decreases to a value
lower than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.10 |
hwAdsl2DownstreamRateIncreaseAlarmTrapADSL channel downstream rate increases trap.
This trap message is generated when the ADSL channel downstream rate increases to a value
higher than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.11 |
hwAdsl2DownstreamRateDecreaseAlarmTrapADSL channel downstream rate decreases trap.
This trap message is generated when the ADSL channel downstream rate decreases to a value
lower than the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.12 |
hwAdsl2FailedActiveAlarmTrapFailed active trap.
This trap message is generated when it failed to activate the port using the ADSL
line configuration parameters. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.13 |
hwAdsl2ChipsetNotAvailableAlarmTrapChipset not available trap.
This trap message is generated when the ADSL chipset is not available. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.138.1.11.2.0.14 |