Home/Catalog/ADSL2-LINE-MIB

ADSL2-LINE-MIB

AI MIB Summary

The ADSL2-LINE-MIB provides standardized SNMP management for ADSL, ADSL2, and ADSL2+ physical line interfaces, enabling the monitoring of critical performance metrics such as line attenuation, signal-to-noise ratio (SNR) margins, data rates, and error counters (FEC/HEC) defined by ITU-T G.992.3, G.992.4, and G.992.5 standards. This module facilitates the collection of Embedded Operations Channel (EOC) data to diagnose physical layer impairments and manage line configuration across DSLAM and CPE devices.

This document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1am1] and [G.997.1am2]. Note that the revised ITU-T G.997.1 standard also refers to the next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the IANA Considerations section of this document. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices.
Main OID:
adsl2MIB.1.3.6.1.2.1.10.238
352
Objects
Active
Status
7
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-CONF
IF-MIB
SNMPv2-TC
SNMP-FRAMEWORK-MIB
HC-PerfHist-TC-MIB
ADSL2-LINE-TC-MIB

Objects

352 total
Object Name
adsl2MIBThis document defines a Management Information Base (MIB) module for use with network management protocols in the Internet community for the purpose of managing ADSL, ADSL2, and ADSL2+ lines. The MIB module described in RFC 2662 [RFC2662] describes objects used for managing Asymmetric Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1], and [G.992.2]. These object descriptions are based upon the specifications for the ADSL Embedded Operations Channel (EOC) as defined in American National Standards Institute (ANSI) T1E1.413/1995 [T1E1.413] and International Telecommunication Union (ITU-T) G.992.1 [G.992.1] and G.992.2 [G.992.2]. This document does not obsolete RFC 2662 [RFC2662], but rather provides a more comprehensive management model that includes the ADSL2 and ADSL2+ technologies per G.992.3, G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5], respectively). In addition, objects have been added to improve the management of ADSL, ADSL2, and ADSL2+ lines. Additionally, the management framework for New Generation ADSL lines specified by the Digital Subscriber Line Forum (DSLF) has been taken into consideration [TR-90]. That framework is based on ITU-T G.997.1 standard [G.997.1] as well as two amendments: [G.997.1am1] and [G.997.1am2]. Note that the revised ITU-T G.997.1 standard also refers to the next generation of VDSL technology, known as VDSL2, per ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is currently beyond the scope of this document. The MIB module is located in the MIB tree under MIB 2 transmission, as discussed in the IANA Considerations section of this document. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4706: see the RFC itself for full legal notices.
MODULE-IDENTITY
.1.3.6.1.2.1.10.238
adsl2
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1
adsl2Notifications
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.0
adsl2LinePerfFECSThreshAtucThis notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.1
adsl2LinePerfFECSThreshAturThis notification indicates that the FEC seconds threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.2
adsl2LinePerfESThreshAtucThis notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.3
adsl2LinePerfESThreshAturThis notification indicates that the errored seconds threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.4
adsl2LinePerfSESThreshAtucThis notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.5
adsl2LinePerfSESThreshAturThis notification indicates that the severely-errored seconds threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.6
adsl2LinePerfLOSSThreshAtucThis notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.7
adsl2LinePerfLOSSThreshAturThis notification indicates that the LOS seconds threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.8
adsl2LinePerfUASThreshAtucThis notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.9
adsl2LinePerfUASThreshAturThis notification indicates that the unavailable seconds threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.10
adsl2LinePerfCodingViolationsThreshAtucThis notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.11
adsl2LinePerfCodingViolationsThreshAturThis notification indicates that the coding violations threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.12
adsl2LinePerfCorrectedThreshAtucThis notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.13
adsl2LinePerfCorrectedThreshAturThis notification indicates that the corrected blocks (FEC events) threshold has been reached/exceeded for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.14
adsl2LinePerfFailedFullInitThreshThis notification indicates that the failed full initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2+ line.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.15
adsl2LinePerfFailedShortInitThreshThis notification indicates that the failed short initializations threshold has been reached/exceeded for the referred ADSL/ADSL2 or ADSL2+ line.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.16
adsl2LineStatusChangeAtucThis notification indicates that a status change is detected for the referred ATU-C.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.17
adsl2LineStatusChangeAturThis notification indicates that a status change is detected for the referred ATU-R.
NOTIFICATION-TYPE
.1.3.6.1.2.1.10.238.1.0.18
adsl2Line
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.1
adsl2LineTableThe table adsl2LineTable contains configuration, command, and status parameters of the ADSL2 line. The index of this table is an interface index where the interface has an ifType of adsl2plus(238). Several objects in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineEntry
.1.3.6.1.2.1.10.238.1.1.1
adsl2LineEntryThe table adsl2LineTable contains configuration, commands, and status parameters of the ADSL2 line
Adsl2LineEntry
.1.3.6.1.2.1.10.238.1.1.1.1
adsl2LineCnfgTemplateThe value of this object identifies the row in the ADSL2 Line Configuration Templates Table, (adsl2LineConfTemplateTable), which applies for this ADSL2 line. This object MUST be maintained in a persistent manner.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.1.1.1.1
adsl2LineAlarmCnfgTemplateThe value of this object identifies the row in the ADSL2 Line Alarm Configuration Template Table, (adsl2LineAlarmConfTemplateTable), which applies to this ADSL2 line. This object MUST be maintained in a persistent manner.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.1.1.1.2
adsl2LineCmndConfPmsfPower management state forced. Defines the line states to be forced by the near-end ATU on this line. The various possible values are: l3toL0(0), l0toL2(2), or l0orL2toL3(3). This object MUST be maintained in a persistent manner.rw
Adsl2ConfPmsForce (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.3
adsl2LineCmndConfLdsfLoop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end ATU on this line or only be responsive to loop diagnostics initiated by the far-end ATU. This object MUST be maintained in a persistent manner. However, in case the operator forces loop diagnostics mode then the access node should reset the object (inhibit) when loop diagnostics mode procedures are completed.rw
Adsl2LineLdsf (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.4
adsl2LineCmndConfLdsfFailReasonThe status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Possible values are: none(1) - The default value in case LDSF was never requested for the associated line. success(2) - The recent command completed successfully. inProgress(3) - The Loop Diagnostics process is in progress. unsupported(4) - The NE or the line card doesn't support LDSF. cannotRun(5) - The NE cannot initiate the command, due to a nonspecific reason. aborted(6) - The Loop Diagnostics process aborted. failed(7) - The Loop Diagnostics process failed. illegalMode(8) - The NE cannot initiate the command, due to the specific mode of the relevant line. adminUp(9) - The NE cannot initiate the command, as the relevant line is administratively 'Up'. tableFull(10) - The NE cannot initiate the command, due to reaching the maximum number of rows in the results table. noResources(11) - The NE cannot initiate the command, due to lack of internal memory resources.ro
Adsl2LdsfResult (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.5
adsl2LineCmndAutomodeColdStartAutomode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a change in loop conditions applied to the devices under test. The ATUs shall reset any historical information used for automode and for shortening G.994.1 handshake and initialization. Automode is the case where multiple operation-modes are enabled through the adsl2LConfProfAtuTransSysEna object in the line configuration profile being used for the ADSL line, and where the selection of the actual operation-mode depends not only on the common capabilities of both ATUs (as exchanged in G.994.1), but also on achievable data rates under given loop conditions. This object MUST be maintained in a persistent manner.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.1.1.1.6
adsl2LineStatusAtuTransSysThe ATU Transmission System (ATS) in use. It is coded in a bit-map representation with only a single bit set to '1' (the selected coding for the ADSL line). This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. A set of ADSL2 line transmission modes, with one bit per mode.ro
Adsl2TransmissionModeType (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.7
adsl2LineStatusPwrMngStateThe current power management state. One of four possible power management states: L0 - Synchronized and full transmission (i.e., Showtime). L1 - Low Power with reduced net data rate (G.992.2 only). L2 - Low Power with reduced net data rate (G.992.3 and G.992.4 only). L3 - No power. The various possible values are: l0(1), l1(2), l2(3), or l3(4).ro
Adsl2PowerMngState (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.8
adsl2LineStatusInitResultIndicates the result of the last full initialization performed on the line. It is an enumeration type with the following values: noFail(0), configError(1), configNotFeasible(2), commFail(3), noPeerAtu(4), or otherCause(5).ro
Adsl2InitResult (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.9
adsl2LineStatusLastStateDsThe last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line.ro
Adsl2LastTransmittedState (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.10
adsl2LineStatusLastStateUsThe last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line.ro
Adsl2LastTransmittedState (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.11
adsl2LineStatusAturIndicates current state (existing failures) of the ATU-R. This is a bit-map of possible conditions.ro
Adsl2LineStatus (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.12
adsl2LineStatusAtucIndicates current state (existing failures) of the ATU-C. This is a bit-map of possible conditions.ro
Adsl2LineStatus (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.1.1.1.13
adsl2LineStatusLnAttenDsThe measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is currently unavailable.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.14
adsl2LineStatusLnAttenUsThe measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is currently unavailable.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.15
adsl2LineStatusSigAttenDsThe measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is currently unavailable.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.16
adsl2LineStatusSigAttenUsThe measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is currently unavailable.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.17
adsl2LineStatusSnrMarginDsDownstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable.ro
Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.18
adsl2LineStatusSnrMarginUsUpstream SNR Margin is the maximum increase in dB of the noise power received at the ATU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable.ro
Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.19
adsl2LineStatusAttainableRateDsMaximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the ATU-C transmitter and the ATU-R receiver, coded in bits/second.ro
Unsigned32 UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.1.1.1.20
adsl2LineStatusAttainableRateUsMaximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the ATU-R transmitter and the ATU-C receiver, coded in bits/second.ro
Unsigned32 UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.1.1.1.21
adsl2LineStatusActPsdDsActual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented.ro
Integer32 (-900..0 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.22
adsl2LineStatusActPsdUsActual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (physical values are -90 to 0 dBm/Hz). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented.ro
Integer32 (-900..0 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.23
adsl2LineStatusActAtpDsActual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the ATU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented.ro
Integer32 (-310..310 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.24
adsl2LineStatusActAtpUsActual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the ATU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented.ro
Integer32 (-310..310 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.1.1.1.25
adsl2Status
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.2
adsl2ChannelStatusTableThe table adsl2ChannelStatusTable contains status parameters of the ADSL2 channel. This table contains live data from equipment.
SEQUENCE OF Adsl2ChannelStatusEntry
.1.3.6.1.2.1.10.238.1.2.1
adsl2ChannelStatusEntryThe table adsl2ChannelStatusTable contains status parameters of the ADSL2 channel. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit.
Adsl2ChannelStatusEntry
.1.3.6.1.2.1.10.238.1.2.1.1
adsl2ChStatusUnitThe termination unit atuc(1) or atur(2).
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.2.1.1.1
adsl2ChStatusChannelNumProvides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.2.1.1.2
adsl2ChStatusActDataRateThe actual net data rate that the bearer channel is operating at, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. The data rate is coded in bits/second.ro
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.2.1.1.3
adsl2ChStatusPrevDataRateThe previous net data rate that the bearer channel was operating at just before the latest rate change event. This could be a full or short initialization, fast retrain, DRA or power management transitions, excluding transitions between L0 state and L1 or L2 states. The data rate is coded in bits/second.ro
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.2.1.1.4
adsl2ChStatusActDelayThe actual one-way interleaving delay introduced by the PMS-TC in the direction of the bearer channel, if in L0 power management state. In L1 or L2 states, it relates to the previous L0 state. It is coded in ms (rounded to the nearest ms).ro
Unsigned32 (0..8176 ) UNITS "milliseconds"
.1.3.6.1.2.1.10.238.1.2.1.1.5
adsl2ChStatusAtmStatusIndicates the current state (existing failures) of the ADSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), noCellDelineation(1), or lossOfCellDelineation(2). In the case where the channel is not an ATM Data Path, the object is set to '0'.ro
Adsl2ChAtmStatus (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.2.1.1.6
adsl2ChStatusPtmStatusIndicates the current state (existing failures) of the ADSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. The various bit positions are: noDefect(0), or outOfSync(1). In the case where the channel is not a PTM Data Path, the object is set to '0'.ro
Adsl2ChPtmStatus (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.2.1.1.7
adsl2SCStatusTableThe table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The following points apply to this table: 1. The main purpose of this table is to hold the results of a DELT. 2. This table also holds parameters obtained at line initialization time. 3. The rows in this table are volatile; that is, they are lost if the SNMP agent is rebooted. 4. Due to the large OCTET STRING attributes in this table, the worst case memory requirements for this table are very high. The manager may use the row status attribute of this table to delete rows in order to reclaim memory. 5. The manager may create rows in this table. The SNMP agent may create rows in this table. Only the manager may delete rows in this table. 6. The maximum number of rows allowable in this table is indicated by the scalar attribute adsl2ScalarSCMaxInterfaces. The number of rows available in this table is indicated by the scalar attribute adsl2ScalarSCAvailInterfaces. 7. The SNMP agent is permitted to create rows in this table when a DELT completes successfully or when line initialization occurs. It is not mandatory for the SNMP agent to create rows in this table; hence, it may be necessary for the manager to create rows in this table before any results can be stored. 8. If the manager attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the response to the SNMP SET PDU will contain the error noCreation(11). 9. If the SNMP agent attempts to create a row in this table and there are no more rows available, the creation attempt will fail, and the attribute adsl2LineCmndConfLdsfFailReason will indicate the reason for the failure. The failure reason will be either tableFull(10) or noResources(11). 10. An example of use of this table is as follows: Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes, and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : Due to a low memory condition, a row in the : adsl2SCStatusTable table cannot be created at : this time. Step 5. : The reason for the failure, tableFull(10), is : indicated in the adsl2LineCmndConfLdsfFailReason : attribute. 11. Another example of use of this table is as follows : Step 1. : The DELT is started by setting the : adsl2LineCmndConfLdsf from inhibit to force. Step 2. : The DELT completes and valid data is : available. Step 3. : The row in the adsl2SCStatusTable where the : results will be stored does not yet exist so : the SNMP agent attempts to create the row. Step 4. : The row creation is successful. Step 5. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2). 12. Another example of use of this table is as follows: Step 1. : The manager creates a row in adsl2SCStatusTable : for a particular ADSL2 line. Step 2. : The DELT is started on the above-mentioned : line by setting the adsl2LineCmndConfLdsf from : inhibit to force. Step 3. : The DELT completes, and valid data is : available. Step 4. : The value of the attribute : adsl2LineCmndConfLdsfFailReasonreason is set : to success(2).
SEQUENCE OF Adsl2SCStatusEntry
.1.3.6.1.2.1.10.238.1.2.2
adsl2SCStatusEntryThe table Adsl2SCStatusEntry contains status parameters of the ADSL2 sub-carriers. The index of this table is an interface index where the interface has an ifType of adsl2plus(238).
Adsl2SCStatusEntry
.1.3.6.1.2.1.10.238.1.2.2.1
adsl2SCStatusDirectionThe direction of the sub-carrier is either upstream or downstream.
Adsl2Direction (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.2.2.1.1
adsl2SCStatusMtimeSNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated otherwise.ro
Unsigned32 UNITS "symbols"
.1.3.6.1.2.1.10.238.1.2.2.1.2
adsl2SCStatusSnrThe SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.3
adsl2SCStatusBitsAllocThe bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.4
adsl2SCStatusGainAllocThe gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.5
adsl2SCStatusTssiThe transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index of the subcarrier used in the context of the breakpoint. Third octet - The shaping parameter at the breakpoint. Subcarrier index is an unsigned number in the range 1 to either NSCds (downstream direction) or NSCus (upstream direction). The shaping parameter value is in the range 0 to 127 (units of -0.5dB). The special value 127 indicates that the subcarrier is not transmitted.ro
Adsl2Tssi (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.2.2.1.6
adsl2SCStatusLinScaleThe scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.2.2.1.7
adsl2SCStatusLinRealAn array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real component [referred to here as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) and b(i) [provided by the Adsl2SubcarrierLinImg object] are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.8
adsl2SCStatusLinImgAn array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the imaginary component [referred to here as b(i)] of Hlin(f = i*Df) value for a particular sub- carrier index i (0 <= i < NSC). Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)), where scale is Adsl2SubcarrierLinScale and a(i) [provided by the Adsl2SubcarrierLinReal object] and b(i) are in the range (-2^15+1) to (+2^15-1). A special value a(i)=b(i)= -2^15 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is only available after a loop diagnostic procedure. Each value in this array is 16 bits wide and is stored in big endian format.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.9
adsl2SCStatusLogMtThe number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initializationro
Unsigned32
.1.3.6.1.2.1.10.238.1.2.2.1.10
adsl2SCStatusLogAn array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.11
adsl2SCStatusQlnMtThe number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 second time interval for G.992.3). This parameter corresponds to 1 second in loop diagnostic procedure and should be updated in initializationro
Unsigned32
.1.3.6.1.2.1.10.238.1.2.2.1.12
adsl2SCStatusQlnAn array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.2.2.1.13
adsl2SCStatusLnAttenWhen referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub-carriers during diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub-carriers during diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the line attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the line attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.2.2.1.14
adsl2SCStatusSigAttenWhen referring to the downstream direction, it is the measured difference in the total power transmitted by the ATU-C and the total power received by the ATU-R over all sub- carriers during Showtime after the diagnostics mode. When referring to the upstream direction, it is the measured difference in the total power transmitted by the ATU-R and the total power received by the ATU-C over all sub- carriers during Showtime after the diagnostics mode. It ranges from 0 to 1270 units of 0.1 dB (physical values are 0 to 127 dB). A special value of 0x7FFFFFFF (2147483647) indicates the signal attenuation is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the signal attenuation measurement is unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.ro
Unsigned32 (0..1270 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.2.2.1.15
adsl2SCStatusSnrMarginSNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.ro
Integer32 (-640..630 | 2147483646 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.2.2.1.16
adsl2SCStatusAttainableRateMaximum Attainable Data Rate. The maximum net data rate currently attainable by the ATU-C transmitter and ATU-R receiver (when referring to downstream direction) or by the ATU-R transmitter and ATU-C receiver (when referring to upstream direction). Value is coded in bits/second. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.ro
Unsigned32 UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.2.2.1.17
adsl2SCStatusActAtpActual Aggregate Transmit Power from the ATU (ATU-R on downstream direction and ATU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (physical values are -31 to 31 dBm). A value of all 1's indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.ro
Integer32 UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.2.2.1.18
adsl2SCStatusRowStatusRow Status. The manager may create and delete rows of this table. Please see the description of adsl2SCStatusTable above for more details.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.2.2.1.19
adsl2Inventory
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.3
adsl2LineInventoryTableThe table adsl2LineInventoryTable contains inventory of the ADSL2 units.
SEQUENCE OF Adsl2LineInventoryEntry
.1.3.6.1.2.1.10.238.1.3.1
adsl2LineInventoryEntryThe table adsl2LineInventoryTable contains inventory of the ADSL2 units. The index of this table is an interface index where the interface has an ifType of adsl2plus(238).
Adsl2LineInventoryEntry
.1.3.6.1.2.1.10.238.1.3.1.1
adsl2LInvUnitThe termination unit atuc(1) or atur(2).
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.3.1.1.1
adsl2LInvG994VendorIdThe ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.3.1.1.2
adsl2LInvSystemVendorIdThe ATU System Vendor ID (identifies the ATU system integrator) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of 8 binary octets, with the same format as used for Adsl2InvG994VendorId.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.3.1.1.3
adsl2LInvVersionNumberThe ATU version number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It consists of up to 16 binary octets.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.3.1.1.4
adsl2LInvSerialNumberThe ATU serial number (vendor-specific information) as inserted in the Overhead Messages (both ATUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only ATU-R in G.992.1 and G.992.2). It is vendor-specific information. It consists of up to 32 ASCII characters.ro
OCTET STRING
.1.3.6.1.2.1.10.238.1.3.1.1.5
adsl2LInvSelfTestResultThe ATU self-test result, coded as a 32-bit value. The most significant octet of the result is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discretionary.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.3.1.1.6
adsl2LInvTransmissionCapabilitiesThe ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1. A set of ADSL2 line transmission modes, with one bit per mode.ro
Adsl2TransmissionModeType (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.3.1.1.7
adsl2PM
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.4
adsl2PMLine
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.4.1
adsl2PMLineCurrTableThe table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 lines.
SEQUENCE OF Adsl2PMLineCurrEntry
.1.3.6.1.2.1.10.238.1.4.1.1
adsl2PMLineCurrEntryThe table adsl2PMLineCurrTable contains current Performance Monitoring results of ADSL2 lines. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), along with a termination unit. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.
Adsl2PMLineCurrEntry
.1.3.6.1.2.1.10.238.1.4.1.1.1
adsl2PMLCurrUnitThe termination unit atuc(1) or atur(2).
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.1.1.1.1
adsl2PMLCurrValidIntervalsValid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.1.1.2
adsl2PMLCurrInvalidIntervalsInvalid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.1.1.3
adsl2PMLCurr15MTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.4
adsl2PMLCurr15MFecsCount of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.5
adsl2PMLCurr15MEsCount of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 . This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.6
adsl2PMLCurr15MSesCount of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 . This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.7
adsl2PMLCurr15MLossCount of seconds during this interval where there was LOS (or LOS-FE for ATU-R).ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.8
adsl2PMLCurr15MUasCount of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.9
adsl2PMLCurr1DayValidIntervalsValid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.1.1.10
adsl2PMLCurr1DayInvalidIntervalsInvalid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.1.1.11
adsl2PMLCurr1DayTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.12
adsl2PMLCurr1DayFecsCount of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.13
adsl2PMLCurr1DayEsCount of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.14
adsl2PMLCurr1DaySesCount of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.15
adsl2PMLCurr1DayLossCount of seconds during this interval where there was LOS (or LOS-FE for ATU-R).ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.16
adsl2PMLCurr1DayUasCount of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.1.1.17
adsl2PMLineCurrInitTableThe table adsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.
SEQUENCE OF Adsl2PMLineCurrInitEntry
.1.3.6.1.2.1.10.238.1.4.1.2
adsl2PMLineCurrInitEntryThe table adsl2PMLineCurrInitTable contains current initialization counters of the ADSL2 line. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), and a termination unit.
Adsl2PMLineCurrInitEntry
.1.3.6.1.2.1.10.238.1.4.1.2.1
adsl2PMLCurrInit15MTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.2.1.1
adsl2PMLCurrInit15MFullInitsCount of full initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.2
adsl2PMLCurrInit15MFailedFullInitsCount of failed full initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.3
adsl2PMLCurrInit15MShortInitsCount of short initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.4
adsl2PMLCurrInit15MFailedShortInitsCount of failed short initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.5
adsl2PMLCurrInit1DayTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.2.1.6
adsl2PMLCurrInit1DayFullInitsCount of full initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.7
adsl2PMLCurrInit1DayFailedFullInitsCount of failed full initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.8
adsl2PMLCurrInit1DayShortInitsCount of short initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.9
adsl2PMLCurrInit1DayFailedShortInitsCount of failed short initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.2.1.10
adsl2PMLineHist15MinTableThe table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of the ADSL2 line.
SEQUENCE OF Adsl2PMLineHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.1.3
adsl2PMLineHist15MinEntryThe table adsl2PMLineHist15MinTable contains PM line history for 15min intervals of the ADSL2 line. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), along with a termination unit, and an interval number.
Adsl2PMLineHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.1.3.1
adsl2PMLHist15MUnitThe termination unit atuc(1) or atur(2).
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.1.3.1.1
adsl2PMLHist15MIntervalThe interval number.
Unsigned32 (1..96 )
.1.3.6.1.2.1.10.238.1.4.1.3.1.2
adsl2PMLHist15MMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.3
adsl2PMLHist15MFecsCount of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.4
adsl2PMLHist15MEsCount of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.5
adsl2PMLHist15MSesCount of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.6
adsl2PMLHist15MLossCount of seconds during this interval where there was LOS (or LOS-FE for ATU-R).ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.7
adsl2PMLHist15MUasCount of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.3.1.8
adsl2PMLHist15MValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.1.3.1.9
adsl2PMLineHist1DayTableThe table adsl2PMLineHist1DayTable contains PM line history for 24-hour intervals of the ADSL2 line.
SEQUENCE OF Adsl2PMLineHist1DayEntry
.1.3.6.1.2.1.10.238.1.4.1.4
adsl2PMLineHist1DayEntryThe table adsl2PMLineHist1DayTable contains PM line history for 24-hour intervals of the ADSL2 line. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), along with a termination unit, and an interval number.
Adsl2PMLineHist1DayEntry
.1.3.6.1.2.1.10.238.1.4.1.4.1
adsl2PMLHist1DUnitThe termination unit.
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.1.4.1.1
adsl2PMLHist1DIntervalThe interval number.
Unsigned32 (1..30 )
.1.3.6.1.2.1.10.238.1.4.1.4.1.2
adsl2PMLHist1DMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.3
adsl2PMLHist1DFecsCount of seconds during this interval where there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.4
adsl2PMLHist1DEsCount of seconds during this interval where there was: ATU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 ATU-R: FEBE >= 1 for one or more bearer channels OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.5
adsl2PMLHist1DSesCount of seconds during this interval where there was: ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >> 1 OR LPR >= 1 ATU-R: (FEBE summed over all bearer channels) >= 18 OR LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1. This parameter is inhibited during UAS.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.6
adsl2PMLHist1DLossCount of seconds during this interval where there was LOS (or LOS-FE for ATU-R).ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.7
adsl2PMLHist1DUasCount of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely- errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.ro
Counter32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.4.1.8
adsl2PMLHist1DValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.1.4.1.9
adsl2PMLineInitHist15MinTableThe table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15-minute intervals of the ADSL2 line.
SEQUENCE OF Adsl2PMLineInitHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.1.5
adsl2PMLineInitHist15MinEntryThe table adsl2PMLineInitHist15MinTable contains PM line initialization history for 15 minutes intervals of the ADSL2 line. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), and an interval number.
Adsl2PMLineInitHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.1.5.1
adsl2PMLHistInit15MIntervalThe interval number.
Unsigned32 (1..96 )
.1.3.6.1.2.1.10.238.1.4.1.5.1.1
adsl2PMLHistInit15MMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.5.1.2
adsl2PMLHistInit15MFullInitsCount of full initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.5.1.3
adsl2PMLHistInit15MFailedFullInitsCount of failed full initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.5.1.4
adsl2PMLHistInit15MShortInitsCount of short initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.5.1.5
adsl2PMLHistInit15MFailedShortInitsCount of failed short initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.5.1.6
adsl2PMLHistInit15MValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.1.5.1.7
adsl2PMLineInitHist1DayTableThe table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24-hour intervals of the ADSL2 line.
SEQUENCE OF Adsl2PMLineInitHist1DayEntry
.1.3.6.1.2.1.10.238.1.4.1.6
adsl2PMLineInitHist1DayEntryThe table adsl2PMLineInitHist1DayTable contains PM line initialization history for 24-hour intervals of the ADSL2 line. The index of this table consists of an interface index, where the interface has an ifType of adsl2plus(238), and an interval number.
Adsl2PMLineInitHist1DayEntry
.1.3.6.1.2.1.10.238.1.4.1.6.1
adsl2PMLHistinit1DIntervalThe interval number.
Unsigned32 (1..30 )
.1.3.6.1.2.1.10.238.1.4.1.6.1.1
adsl2PMLHistinit1DMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.1.6.1.2
adsl2PMLHistinit1DFullInitsCount of full initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.6.1.3
adsl2PMLHistinit1DFailedFullInitsCount of failed full initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.6.1.4
adsl2PMLHistinit1DShortInitsCount of short initializations attempted on the line (successful and failed) during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.6.1.5
adsl2PMLHistinit1DFailedShortInitsCount of failed short initializations on the line during this interval.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.1.6.1.6
adsl2PMLHistinit1DValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.1.6.1.7
adsl2PMChannel
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.4.2
adsl2PMChCurrTableThe table adsl2PMChCurrTable contains current Performance Monitoring results of the ADSL2 channel. The PM counters in the table are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.
SEQUENCE OF Adsl2PMChCurrEntry
.1.3.6.1.2.1.10.238.1.4.2.1
adsl2PMChCurrEntryThe table adsl2PMChCurrTable contains current Performance Monitoring results of the ADSL2 channel. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit.
Adsl2PMChCurrEntry
.1.3.6.1.2.1.10.238.1.4.2.1.1
adsl2PMChCurrUnitThe termination unit.
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.2.1.1.1
adsl2PMChCurrValidIntervalsValid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.2
adsl2PMChCurrInvalidIntervalsInvalid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.3
adsl2PMChCurr15MTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.2.1.1.4
adsl2PMChCurr15MCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.5
adsl2PMChCurr15MCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.6
adsl2PMChCurr1DayValidIntervalsValid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.7
adsl2PMChCurr1DayInvalidIntervalsInvalid intervals.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.8
adsl2PMChCurr1DayTimeElapsedTotal elapsed seconds since this PM interval began. Note that the PM counters are not reset even when the XTU is reinitialized. They are reinitialized only when the agent itself is reset or reinitialized.ro
HCPerfTimeElapsed UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.2.1.1.9
adsl2PMChCurr1DayCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.10
adsl2PMChCurr1DayCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.1.1.11
adsl2PMChHist15MinTableThe table adsl2PMChCurrTable contains current Performance Monitoring results of the ADSL2 channel.
SEQUENCE OF Adsl2PMChHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.2.2
adsl2PMChHist15MinEntryThe table adsl2PMChCurrTable contains current Performance Monitoring results of the ADSL2 channel. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit, and the interval number.
Adsl2PMChHist15MinEntry
.1.3.6.1.2.1.10.238.1.4.2.2.1
adsl2PMChHist15MUnitThe termination unit.
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.2.2.1.1
adsl2PMChHist15MIntervalThe interval number.
Unsigned32 (1..96 )
.1.3.6.1.2.1.10.238.1.4.2.2.1.2
adsl2PMChHist15MMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.2.2.1.3
adsl2PMChHist15MCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.2.1.4
adsl2PMChHist15MCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.2.1.5
adsl2PMChHist15MValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.2.2.1.6
adsl2PMChHist1DTableThe table adsl2PMChHist1DayTable contains PM channel history for 1-day intervals of ADSL2.
SEQUENCE OF Adsl2PMChHist1DEntry
.1.3.6.1.2.1.10.238.1.4.2.3
adsl2PMChHist1DEntryThe table adsl2PMChHist1DayTable contains PM channel history for 1-day intervals of ADSL2. The index of this table consists of an interface index, where the interface has an ifType value that is applicable for a DSL channel, along with a termination unit, and the interval number.
Adsl2PMChHist1DEntry
.1.3.6.1.2.1.10.238.1.4.2.3.1
adsl2PMChHist1DUnitThe termination unit.
Adsl2Unit (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.4.2.3.1.1
adsl2PMChHist1DIntervalThe interval number.
Unsigned32 (1..30 )
.1.3.6.1.2.1.10.238.1.4.2.3.1.2
adsl2PMChHist1DMonitoredTimeTotal seconds monitored in this interval.ro
Unsigned32 UNITS "seconds"
.1.3.6.1.2.1.10.238.1.4.2.3.1.3
adsl2PMChHist1DCodingViolationsCount of CRC-8 (FEBE for ATU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.3.1.4
adsl2PMChHist1DCorrectedBlocksCount of FEC (FFEC for ATU-R) anomalies (corrected code words) occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the FEC is applied over multiple channels, then each related FEC (or FFEC) anomaly should increment each of the counters related to the individual channels.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.4.2.3.1.5
adsl2PMChHist1DValidIntervalThis variable indicates if the data for this interval is valid.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.4.2.3.1.6
adsl2Profile
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.5
adsl2ProfileLine
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.5.1
adsl2LineConfTemplateTableThe table adsl2LineConfTemplateTable contains ADSL2 line configuration templates. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineConfTemplateEntry
.1.3.6.1.2.1.10.238.1.5.1.1
adsl2LineConfTemplateEntryThe table adsl2LineConfTemplateTable contains the ADSL2 line configuration template. A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2LineConfTemplateEntry
.1.3.6.1.2.1.10.238.1.5.1.1.1
adsl2LConfTempTemplateNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.1
adsl2LConfTempLineProfileThe value of this object identifies the row in the ADSL2 Line Configuration Profile Table, (adsl2LineConfProfTable), which applies for this ADSL2 line.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.2
adsl2LConfTempChan1ConfProfileThe value of this object identifies the row in the ADSL2 Channel Configuration Profile Table, (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChConfProfileTable table.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.3
adsl2LConfTempChan1RaRatioDsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan1RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.4
adsl2LConfTempChan1RaRatioUsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #1 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.5
adsl2LConfTempChan2ConfProfileThe value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #2. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if adsl2LConfTempChan3ConfProfile contains a zero-length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.6
adsl2LConfTempChan2RaRatioDsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.7
adsl2LConfTempChan2RaRatioUsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #2 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.8
adsl2LConfTempChan3ConfProfileThe value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #3. If the channel is unused, then the object is set to a zero-length string. This object may be set to a zero-length string only if adsl2LConfTempChan4ConfProfile contains a zero-length string. This object may be set to a non-zero-length string only if adsl2LConfTempChan2ConfProfile contains a non-zero-length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.9
adsl2LConfTempChan3RaRatioDsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan3RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels on Downstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.10
adsl2LConfTempChan3RaRatioUsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #3 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels on Upstream direction. The sum of rate adaptation ratios over all bearers on the same direction shall be equal to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.11
adsl2LConfTempChan4ConfProfileThe value of this object identifies the row in the ADSL2 Channel Configuration Profile Table (adsl2ChConfProfileTable) that applies to ADSL2 bearer channel #4. If the channel is unused, then the object is set to a zero-length string. This object may be set to a non-zero-length string only if adsl2LConfTempChan3ConfProfile contains a non-zero-length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.1.1.12
adsl2LConfTempChan4RaRatioDsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Downstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioDs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.13
adsl2LConfTempChan4RaRatioUsRate Adaptation Ratio. The ratio (in %) that should be taken into account for the bearer channel #4 when performing rate adaptation on Upstream. The ratio refers to the available data rate in excess of the Minimum Data Rate, summed over all bearer channels. Also, the 100 - adsl2LConfTempChan4RaRatioUs is the ratio of excess data rate to be assigned to all other bearer channels. The sum of rate adaptation ratios over all bearers on the same direction shall sum to 100%.rw
Unsigned32 (0..100 ) UNITS "percent"
.1.3.6.1.2.1.10.238.1.5.1.1.1.14
adsl2LConfTempRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated lines.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.1.1.1.15
adsl2LineConfProfTableThe table adsl2LineConfProfTable contains ADSL2 line profile configuration. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineConfProfEntry
.1.3.6.1.2.1.10.238.1.5.1.2
adsl2LineConfProfEntryThe table adsl2LineConfProfTable contains ADSL2 line profile configuration. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2LineConfProfEntry
.1.3.6.1.2.1.10.238.1.5.1.2.1
adsl2LConfProfProfileNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.1.2.1.1
adsl2LConfProfScMaskDsSub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds < i <= 512) should be set to '1'.rw
Adsl2ScMaskDs (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.2
adsl2LConfProfScMaskUsSub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.rw
Adsl2ScMaskUs (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.3
adsl2LConfProfRfiBandsDsThe subset of downstream PSD mask breakpoints that shall be used to notch an RFI band. The specific interpolation around these points is defined in G.992.5. It is a bitmap of 512 bits that allows referring to up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is part of a notch filter, and if set to '0', the respective sub-carrier is not part of a notch filter. This information complements the specification provided by adsl2LConfProfPsdMaskDs. Note that if NSCds < 512, all bits i (NSCds<i<512) should be set to '0'.rw
Adsl2RfiDs (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.4
adsl2LConfProfRaModeDsThe mode of operation of a rate-adaptive ATU-C in the transmit direction. The parameter can take three values: manual(1), raInit(2), or dynamicRa(3).rw
Adsl2RaMode (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.5
adsl2LConfProfRaModeUsThe mode of operation of a rate-adaptive ATU-R in the transmit direction. The parameter can take three values: manual(1), raInit(2), or dynamicRa(3).rw
Adsl2RaMode (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.6
adsl2LConfProfRaUsNrmDsThe Downstream Up-Shift Noise Margin value, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the adsl2LConfProfRaUsTimeDs, the ATU-R shall attempt to increase the downstream net data rate. The Downstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.7
adsl2LConfProfRaUsNrmUsThe Upstream Up-Shift Noise Margin value, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the adsl2LConfProfRaUsTimeUs, the ATU-C shall attempt to increase the upstream net data rate. The Upstream Up-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.8
adsl2LConfProfRaUsTimeDsThe Downstream Up-Shift Time Interval, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. The interval of time that the downstream noise margin should stay above the Downstream Up-Shift Noise Margin before the ATU-R shall attempt to increase the downstream net data rate. The time interval ranges from 0 to 16383 seconds.rw
Unsigned32 (0..16383 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.9
adsl2LConfProfRaUsTimeUsThe Upstream Up-Shift Time Interval, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay above the Upstream Up-Shift Noise Margin before the ATU-C shall attempt to increase the upstream net data rate. The time interval ranges from 0 to 16383 seconds.rw
Unsigned32 (0..16383 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.10
adsl2LConfProfRaDsNrmsDsThe Downstream Down-Shift Noise Margin value, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the adsl2LConfProfRaDsTimeDs, the ATU-R shall attempt to decrease the downstream net data rate. The Downstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.11
adsl2LConfProfRaDsNrmsUsThe Upstream Down-Shift Noise Margin value, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the adsl2LConfProfRaDsTimeUs, the ATU-C shall attempt to decrease the upstream net data rate. The Upstream Down-Shift Noise Margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.12
adsl2LConfProfRaDsTimeDsThe Downstream Down-Shift Time Interval, to be used when adsl2LConfProfRaModeDs is set to dynamicRa. The interval of time the downstream noise margin should stay below the Downstream Down-Shift Noise Margin before the ATU-R shall attempt to decrease the downstream net data rate. The time interval ranges from 0 to 16383 seconds.rw
Unsigned32 (0..16383 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.13
adsl2LConfProfRaDsTimeUsThe Upstream Down-Shift Time Interval, to be used when adsl2LConfProfRaModeUs is set to dynamicRa. The interval of time the upstream noise margin should stay below the Upstream Down-Shift Noise Margin before the ATU-C shall attempt to decrease the upstream net data rate. The time interval ranges from 0 to 16383 seconds.rw
Unsigned32 (0..16383 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.14
adsl2LConfProfTargetSnrmDsThe minimum Noise Margin the ATU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.15
adsl2LConfProfTargetSnrmUsThe minimum Noise Margin the ATU-C receiver shall achieve, relative to the BER requirement for each of the upstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB).rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.16
adsl2LConfProfMaxSnrmDsThe maximum Noise Margin the ATU-R receiver shall try to sustain. If the Noise Margin is above this level, the ATU-R shall request that the ATU-C reduce the ATU-C transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum.rw
Unsigned32 (0..310 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.17
adsl2LConfProfMaxSnrmUsThe maximum Noise Margin the ATU-C receiver shall try to sustain. If the Noise Margin is above this level, the ATU-C shall request that the ATU-R reduce the ATU-R transmit power to get a noise margin below this limit (if this functionality is supported). The maximum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0x7FFFFFFF (2147483647) means that there is no maximum.rw
Unsigned32 (0..310 | 2147483647) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.18
adsl2LConfProfMinSnrmDsThe minimum Noise Margin the ATU-R receiver shall tolerate. If the noise margin falls below this level, the ATU-R shall request that the ATU-C increase the ATU-C transmit power. If an increase to ATU-C transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-R shall fail and attempt to reinitialize, and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0 means that there is no minimum.rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.19
adsl2LConfProfMinSnrmUsThe minimum Noise Margin the ATU-C receiver shall tolerate. If the noise margin falls below this level, the ATU-C shall request that the ATU-R increase the ATU-R transmit power. If an increase of ATU-R transmit power is not possible, a loss-of-margin (LOM) defect occurs, the ATU-C shall fail and attempt to reinitialize, and the NMS shall be notified. The minimum noise margin ranges from 0 to 310 units of 0.1 dB (physical values are 0 to 31 dB). A value of 0 means that there is no minimum.rw
Unsigned32 (0..310 ) UNITS "0.1 dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.20
adsl2LConfProfMsgMinUsMinimum Overhead Rate Upstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in upstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.rw
Unsigned32 (4000..63000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.1.2.1.21
adsl2LConfProfMsgMinDsMinimum Overhead Rate Downstream. Defines the minimum rate of the message-based overhead that shall be maintained by the ATU in downstream direction. Expressed in bits per second and ranges from 4000 to 63000 bps.rw
Unsigned32 (4000..63000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.1.2.1.22
adsl2LConfProfAtuTransSysEnaATU Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATUs may apply the respective coding for the ADSL line. A bit set to '0' means that the ATUs cannot apply the respective coding for the ADSL line. All 'reserved' bits should be set to '0'.rw
Adsl2TransmissionModeType (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.23
adsl2LConfProfPmModePower management state Enabling. Defines the power states the ATU-C or ATU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle(0) and allowTransitionsToLowPower(1). A bit with a '1' value means that the ATU is allowed to transit into the respective state, and a '0' value means that the ATU is not allowed to transit into the respective state.rw
Adsl2LConfProfPmMode (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.2.1.24
adsl2LConfProfL0TimeThis minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds.rw
Unsigned32 (0..255 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.25
adsl2LConfProfL2TimeThis minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds.rw
Unsigned32 (0..255 ) UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.1.2.1.26
adsl2LConfProfL2AtprThe maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB.rw
Unsigned32 (0..31 ) UNITS "dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.27
adsl2LConfProfL2AtprtThe total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims.rw
Unsigned32 (0..31 ) UNITS "dB"
.1.3.6.1.2.1.10.238.1.5.1.2.1.28
adsl2LConfProfRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.1.2.1.29
adsl2LineConfProfModeSpecTableThe table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters. A row in this table that has an index of adsl2LConfProfAdslMode == defMode(1) is called a 'mandatory' row. A row in this table that has an index such that adsl2LConfProfAdslMode is not equal to defMode(1) is called an 'optional' row. When a row in the adsl2LineConfProfTable table (the parent row) is created, the SNMP agent will automatically create a 'mandatory' row in this table. When the parent row is deleted, the SNMP agent will automatically delete all associated rows in this table. Any attempt to delete the 'mandatory' row using the adsl2LConfProfModeSpecRowStatus attribute will be rejected by the SNMP agent. The manager MAY create an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute if the parent row exists. The manager MAY delete an 'optional' row in this table using the adsl2LConfProfModeSpecRowStatus attribute at any time. If the actual transmission mode of a DSL line does not match one of the 'optional' rows in this table, then the line will use the PSD configuration from the 'mandatory' row. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineConfProfModeSpecEntry
.1.3.6.1.2.1.10.238.1.5.1.3
adsl2LineConfProfModeSpecEntryThe table adsl2LineConfProfModeSpecTable extends the ADSL2 line configuration profile by ADSL Mode Specific parameters.
Adsl2LineConfProfModeSpecEntry
.1.3.6.1.2.1.10.238.1.5.1.3.1
adsl2LConfProfAdslModeThe ADSL Mode is a way of categorizing the various ADSL transmission modes into groups; each group (ADSL Mode) shares the same PSD configuration. There should be multiple entries in this table for a given line profile in case multiple bits are set in adsl2LConfProfAtuTransSysEna for that profile.
Adsl2OperationModes (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.3.1.1
adsl2LConfProfMaxNomPsdDsThe maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz).rw
Integer32 (-600..-300 ) UNITS "0.1 dBm/Hz"
.1.3.6.1.2.1.10.238.1.5.1.3.1.2
adsl2LConfProfMaxNomPsdUsThe maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz (physical values are -60 to -30 dBm/Hz).rw
Integer32 (-600..-300 ) UNITS "0.1 dBm/Hz"
.1.3.6.1.2.1.10.238.1.5.1.3.1.3
adsl2LConfProfMaxNomAtpDsThe maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).rw
Unsigned32 (0..255 ) UNITS "0.1 dBm"
.1.3.6.1.2.1.10.238.1.5.1.3.1.4
adsl2LConfProfMaxNomAtpUsThe maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm).rw
Unsigned32 (0..255 ) UNITS "0.1 dBm"
.1.3.6.1.2.1.10.238.1.5.1.3.1.5
adsl2LConfProfMaxAggRxPwrUsThe maximum upstream aggregate receive power over the relevant set of sub-carriers. The ATU-C should verify that the upstream power cutback is such that this maximum aggregate receive power value is honored. It ranges from -255 to 255 units of 0.1 dBm (physical values are -25.5 to 25.5 dBm). A value of 0x7FFFFFFF (2147483647) means that there is no limit.rw
Integer32 (-255..255 | 2147483647) UNITS "0.1 dBm"
.1.3.6.1.2.1.10.238.1.5.1.3.1.6
adsl2LConfProfPsdMaskDsThe downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 to NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.rw
Adsl2PsdMaskDs (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.3.1.7
adsl2LConfProfPsdMaskUsThe upstream PSD mask applicable at the U-R2 reference point. This parameter is used only for G.992.5, and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G.992.5. This is a string of 4 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a 4th breakpoint. Each subcarrier index is an unsigned number in the range 1 to NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.rw
Adsl2PsdMaskUs (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.1.3.1.8
adsl2LConfProfPsdMaskSelectUsThe selected upstream PSD mask. This parameter is used only for annexes J and M of G.992.3 and G.992.5, and the same selection is used for all relevant enabled bits in adsl2LConfProfAtuTransSysEna.rw
Unsigned32 (1..9 )
.1.3.6.1.2.1.10.238.1.5.1.3.1.9
adsl2LConfProfModeSpecRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.1.3.1.10
adsl2ProfileChannel
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.5.2
adsl2ChConfProfileTableThe table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2ChConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.2.1
adsl2ChConfProfileEntryThe table adsl2ChConfProfileTable contains ADSL2 channel profile configuration. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2ChConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.2.1.1
adsl2ChConfProfProfileNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.2.1.1.1
adsl2ChConfProfMinDataRateDsMinimum Data Rate on Downstream direction. The minimum net data rate for the bearer channel, coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.2
adsl2ChConfProfMinDataRateUsMinimum Data Rate on Upstream direction. The minimum net data rate for the bearer channel, coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.3
adsl2ChConfProfMinResDataRateDsMinimum Reserved Data Rate on Downstream direction. The minimum reserved net data rate for the bearer channel, coded in bits/second. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., adsl2LConfProfRaModeDs) is set to dynamicRa.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.4
adsl2ChConfProfMinResDataRateUsMinimum Reserved Data Rate on Upstream direction. The minimum reserved net data rate for the bearer channel, coded in bits/second. This parameter is used only if the Rate Adaptation Mode in the direction of the bearer channel (i.e., adsl2LConfProfRaModeUs) is set to dynamicRa.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.5
adsl2ChConfProfMaxDataRateDsMaximum Data Rate on Downstream direction. The maximum net data rate for the bearer channel, coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.6
adsl2ChConfProfMaxDataRateUsMaximum Data Rate on Upstream direction. The maximum net data rate for the bearer channel, coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.7
adsl2ChConfProfMinDataRateLowPwrDsMinimum Data Rate in Low Power state on Downstream direction. The minimum net data rate for the bearer channel, coded in bits/second, during the low power state (L1 in G.992.2, L2 in G.992.3).rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.8
adsl2ChConfProfMaxDelayDsMaximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (adsl2ChStatusActDelay) is as close as possible to, but less than or equal to, adsl2ChConfProfMaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.rw
Unsigned32 (0..63 ) UNITS "milliseconds"
.1.3.6.1.2.1.10.238.1.5.2.1.1.9
adsl2ChConfProfMaxDelayUsMaximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The ATUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay (adsl2ChStatusActDelay) is as close as possible to, but less than or equal to, adsl2ChConfProfMaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed.rw
Unsigned32 (0..63 ) UNITS "milliseconds"
.1.3.6.1.2.1.10.238.1.5.2.1.1.10
adsl2ChConfProfMinProtectionDsMinimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol.rw
Adsl2SymbolProtection UNITS "symbols"
.1.3.6.1.2.1.10.238.1.5.2.1.1.11
adsl2ChConfProfMinProtectionUsMinimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol), and 1-16 symbols in steps of 1 symbol.rw
Adsl2SymbolProtection UNITS "symbols"
.1.3.6.1.2.1.10.238.1.5.2.1.1.12
adsl2ChConfProfMaxBerDsMaximum Bit Error Ratio on Downstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3(1), eminus5(2), or eminus7(3).rw
Adsl2MaxBer (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.2.1.1.13
adsl2ChConfProfMaxBerUsMaximum Bit Error Ratio on Upstream direction. The maximum bit error ratio for the bearer channel. The parameter can take the following values (for 1E-3, 1E-5 or 1E-7): eminus3(1), eminus5(2), or eminus7(3).rw
Adsl2MaxBer (ADSL2-LINE-TC-MIB)
.1.3.6.1.2.1.10.238.1.5.2.1.1.14
adsl2ChConfProfUsDataRateDsData Rate Threshold Up shift for downstream direction. An 'Up-shift rate change' event is triggered when the actual downstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.15
adsl2ChConfProfDsDataRateDsData Rate Threshold Down-shift for downstream direction. A 'Down-shift rate change' event is triggered when the actual downstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.16
adsl2ChConfProfUsDataRateUsData Rate Threshold Up shift for upstream direction. An 'Up-shift rate change' event is triggered when the actual upstream data rate exceeds, by more than the threshold, the data rate at the last entry into Showtime. The parameter is coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.17
adsl2ChConfProfDsDataRateUsData Rate Threshold Down-shift for upstream direction. A 'Down-shift rate change' event is triggered when the actual upstream data rate is below the data rate at the last entry into Showtime, by more than the threshold. The parameter is coded in bits/second.rw
Unsigned32 (0..200000000 ) UNITS "bits/second"
.1.3.6.1.2.1.10.238.1.5.2.1.1.18
adsl2ChConfProfImaEnabledIMA Mode Enable. The parameter enables the IMA operation mode in the ATM Data Path. Relevant only if the channel is an ATM Data Path. When in 'enable' state, the ATM data path should comply with the requirements for IMA transmission.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.2.1.1.19
adsl2ChConfProfRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.2.1.1.20
adsl2ProfileAlarmConf
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.5.3
adsl2LineAlarmConfTemplateTableThe table adsl2LineAlarmConfTemplateTable contains ADSL2 line configuration templates. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineAlarmConfTemplateEntry
.1.3.6.1.2.1.10.238.1.5.3.1
adsl2LineAlarmConfTemplateEntryThe table adsl2LineAlarmConfTemplateTable contains ADSL2 line PM thresholds templates. A default template with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2LineAlarmConfTemplateEntry
.1.3.6.1.2.1.10.238.1.5.3.1.1
adsl2LAlarmConfTempTemplateNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.1
adsl2LAlarmConfTempLineProfileThe value of this object identifies the row in the ADSL2 Line Thresholds Configuration Profile Table (adsl2LineAlarmConfProfileTable) that applies to this ADSL2 line.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.2
adsl2LAlarmConfTempChan1ConfProfileThe value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #1. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.3
adsl2LAlarmConfTempChan2ConfProfileThe value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #2. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. If the channel is unused, then the object is set to a zero-length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.4
adsl2LAlarmConfTempChan3ConfProfileThe value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #3. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero-length string only if adsl2LAlarmConfTempChan2ConfProfile contains a non-zero- length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.5
adsl2LAlarmConfTempChan4ConfProfileThe value of this object identifies the row in the ADSL2 Channel Thresholds Configuration Profile Table (adsl2ChAlarmConfProfileTable) that applies for ADSL2 bearer channel #4. The channel profile name specified here must match the name of an existing row in the adsl2ChAlarmConfProfileTable table. This object may be set to a non-zero-length string only if adsl2LAlarmConfTempChan3ConfProfile contains a non-zero- length string.rw
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.1.1.6
adsl2LAlarmConfTempRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A template is activated by setting this object to 'active'. When 'active' is set, the system will validate the template. Before a template can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated lines.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.3.1.1.7
adsl2LineAlarmConfProfileTableThe table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2LineAlarmConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.3.2
adsl2LineAlarmConfProfileEntryThe table adsl2LineAlarmConfProfileTable contains ADSL2 line PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2LineAlarmConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.3.2.1
adsl2LineAlarmConfProfileNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.2.1.1
adsl2LineAlarmConfProfileAtucThresh15MinFecsA threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.2
adsl2LineAlarmConfProfileAtucThresh15MinEsA threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.3
adsl2LineAlarmConfProfileAtucThresh15MinSesA threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.4
adsl2LineAlarmConfProfileAtucThresh15MinLossA threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.5
adsl2LineAlarmConfProfileAtucThresh15MinUasA threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.6
adsl2LineAlarmConfProfileAturThresh15MinFecsA threshold for the adsl2PMLCurr15MFecs counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.7
adsl2LineAlarmConfProfileAturThresh15MinEsA threshold for the adsl2PMLCurr15MEs counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.8
adsl2LineAlarmConfProfileAturThresh15MinSesA threshold for the adsl2PMLCurr15MSes counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.9
adsl2LineAlarmConfProfileAturThresh15MinLossA threshold for the adsl2PMLCurr15MLoss counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.10
adsl2LineAlarmConfProfileAturThresh15MinUasA threshold for the adsl2PMLCurr15MUas counter, when adsl2PMLCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
HCPerfIntervalThreshold UNITS "seconds"
.1.3.6.1.2.1.10.238.1.5.3.2.1.11
adsl2LineAlarmConfProfileThresh15MinFailedFullIntA threshold for the adsl2PMLCurrInit15MfailedFullInits counter. The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.2.1.12
adsl2LineAlarmConfProfileThresh15MinFailedShrtIntA threshold for the adsl2PMLCurrInit15MFailedShortInits counter. The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.2.1.13
adsl2LineAlarmConfProfileRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.3.2.1.14
adsl2ChAlarmConfProfileTableThe table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. Entries in this table MUST be maintained in a persistent manner.
SEQUENCE OF Adsl2ChAlarmConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.3.3
adsl2ChAlarmConfProfileEntryThe table adsl2ChAlarmConfProfileTable contains ADSL2 channel PM thresholds profiles. A default profile with an index of 'DEFVAL' will always exist, and its parameters will be set to vendor- specific values, unless otherwise specified in this document.
Adsl2ChAlarmConfProfileEntry
.1.3.6.1.2.1.10.238.1.5.3.3.1
adsl2ChAlarmConfProfileNameThis object identifies a row in this table.
SnmpAdminString
.1.3.6.1.2.1.10.238.1.5.3.3.1.1
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolationsA threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.3.1.2
adsl2ChAlarmConfProfileAtucThresh15MinCorrectedA threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is atuc(1). The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.3.1.3
adsl2ChAlarmConfProfileAturThresh15MinCodingViolationsA threshold for the adsl2PMChCurr15MCodingViolations counter, when adsl2PMChCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.3.1.4
adsl2ChAlarmConfProfileAturThresh15MinCorrectedA threshold for the adsl2PMChCurr15MCorrectedBlocks counter, when adsl2PMChCurrUnit is atur(2). The value 0 means that no threshold is specified for the associated counter.rw
Unsigned32
.1.3.6.1.2.1.10.238.1.5.3.3.1.5
adsl2ChAlarmConfProfileRowStatusThis object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'notInService'), it must first be unreferenced from all associated templates.rw
RowStatus (SNMPv2-TC)
.1.3.6.1.2.1.10.238.1.5.3.3.1.6
adsl2Scalar
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.6
adsl2ScalarSC
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.6.1
adsl2ScalarSCMaxInterfacesThis value determines the upper size of adsl2SCStatusTable. The maximum number of entries in adsl2SCStatusTable is equal to two times the value of this attribute.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.6.1.1
adsl2ScalarSCAvailInterfacesThis value determines the amount of space that is currently available in adsl2SCStatusTable. The number of entries available in adsl2SCStatusTable is equal to two times the value of this attribute.ro
Unsigned32
.1.3.6.1.2.1.10.238.1.6.1.2
adsl2Conformance
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.7
adsl2Groups
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.7.1
adsl2LineGroupThe group of configuration, status, and commands objects on the line level.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.1
adsl2ChannelStatusGroupThe group of status objects on the channel level.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.2
adsl2ChannelStatusAtmGroupThe group of status objects on the data path level when it is ATM.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.3
adsl2ChannelStatusPtmGroupThe group of status objects on the data path level when it is PTM.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.4
adsl2SCStatusGroupThe group of status objects on the sub-carrier level. They are updated as a result of a DELT process.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.5
adsl2LineInventoryGroupThe group of inventory objects per XTU.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.6
adsl2LineConfTemplateGroupThe group of objects in a line configuration template.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.7
adsl2LineConfProfGroupThe group of objects in a line configuration profile.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.8
adsl2LineConfProfRaGroupThe group of objects required for controlling the rate- adaptive behavior of the line.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.9
adsl2LineConfProfMsgMinGroupThe group of objects required for controlling the rate reserved for Overhead traffic.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.10
adsl2LineConfProfModeSpecGroupThe group of objects in a line configuration profile that have an instance for each operation mode allowed.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.11
adsl2ChConfProfileGroupThe group of objects in a channel configuration profile.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.12
adsl2ChConfProfileAtmGroupThe group of configuration objects required when the data path is ATM.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.13
adsl2ChConfProfileMinResGroupThe group of configuration objects required for the reserved data rate.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.14
adsl2LineAlarmConfTemplateGroupThe group of objects in a line alarm template.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.15
adsl2LineAlarmConfProfileGroupThe group of objects in a line alarm profile.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.16
adsl2ChAlarmConfProfileGroupThe group of objects in a channel alarm profile.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.17
adsl2PMLineCurrGroupThe group of objects that report the line-level counters for current PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.18
adsl2PMLineCurrInitGroupThe group of objects that report the full initialization counters for current PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.19
adsl2PMLineCurrInitShortGroupThe group of objects that report the short initialization counters for current PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.20
adsl2PMLineHist15MinGroupThe group of line-level PM counters for the previous 15-minute interval.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.21
adsl2PMLineHist1DayGroupThe group of line-level PM counters for the previous 24-hour interval.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.22
adsl2PMLineInitHist15MinGroupThe group of PM counters for the previous 15-minute interval's full initializations.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.23
adsl2PMLineInitHist15MinShortGroupThe group of PM counters for the previous 15-minute interval's short initializations.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.24
adsl2PMLineInitHist1DayGroupThe group of PM counters for the previous 24-hour interval's full initializations.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.25
adsl2PMLineInitHist1DayShortGroupThe group of PM counters for the previous 24-hour interval's short initializations.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.26
adsl2PMChCurrGroupThe group of objects that report the channel-level counters for current PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.27
adsl2PMChHist15MinGroupThe group of objects that report the channel-level counters for previous 15-minute PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.28
adsl2PMChHist1DGroupThe group of objects that report the channel-level counters for previous 24-hour PM intervals.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.29
adsl2ScalarSCGroupThe group of objects that report the available memory resources for DELT processes.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.30
adsl2ThreshNotificationGroupThis group supports notifications of significant conditions associated with ADSL/ADSL2/ADSL2+ lines.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.31
adsl2StatusChangeNotificationGroupThis group supports notifications of threshold crossing associated with ADSL/ADSL2/ADSL2+ lines.
Unknown
.1.3.6.1.2.1.10.238.1.7.1.32
adsl2Compliances
OBJECT IDENTIFIER
.1.3.6.1.2.1.10.238.1.7.2
adsl2LineMibComplianceThe compliance statement for SNMP entities that manage ADSL/ADSL2 or ADSL2+ interfaces.
Unknown
.1.3.6.1.2.1.10.238.1.7.2.1
ADSL2-LINE-MIB - SNMP MIB Reference | MIBs Explorer