HUAWEI-MPLSOAM-PS-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for HUAWEI-MPLSOAM-PS-MIB.
38
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
38 total| Object Name |
|---|
hwMplsOamPs OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1 |
hwMplsPsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.3 |
hwMplsPsTableThis table specifies per-protection-group MPLS PS
capability and associated information. SEQUENCE OF HwMplsPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.1 |
hwMplsPsEntryAn entry in this table is created by an LSR for every
protection group capable of supporting mpls ps. HwMplsPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.1.1 |
hwMplsPsIndexThis is a unique index for an entry in the mplspsEntry.ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.1 |
hwMplsPsTypeThe type of protection switch,can be 1:1,1+1,shared mesh,
packet 1+1,the default choice is 1:1.
In the 1+1 architecture type, a protection LSP is dedicated to
each working LSP with the working LSP bridged onto the
protection LSP at the source of the protection domain.
The traffic on working and protection LSPs is transmitted
simultaneously to the sink of the protection domain,
where a selection between the working and protection LSP is
made, based on some predetermined criteria, such as defect
indication.
In the 1:1 architecture type, a protection LSP is dedicated to
each working LSP. The working traffic is transmitted either by
working or protection LSP.
In the shared mesh architecture type, possible sharing of
protection capacity between disjoint link, node in the network
is achieved while guaranteeing recovery from a single failure.
In the packet 1+1 architecture type, the traffic is transmitted
simultaneously onto two possibly disjoint routed LSPs to the
sink of the protection domain. Each pair of duplicate
transmitted packets is assigned the same identifier (sequence
number) but distinct from the other pairs of duplicate packets.
At the sink of the protection domain packet level selection
mechanism is employed to select one of the two possibly
received copies of each packet.
1: 1:1 protection switching,;
2: 1+1 protection switching;
3: shared mesh protection swiching;
4: packet 1+1 protection switching.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.2 |
hwMplsPsWorkTunnNameThe name of work-tunnel.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3 |
hwMplsPsWorkTunnIdWork-tunnel id(session-tunnel-id).ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.4 |
hwMplsPsProtectTunnNameThe name of protect-tunnel.ro OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.5 |
hwMplsPsProtectTunnIdProtect-tunnel id(session-tunnel-id).ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.6 |
hwMplsPsRevertiveModeRevertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in a
non-revertive mode.
1: revertive;
2: non-revertive;ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.7 |
hwMplsPsWTRWait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer has
expired.The default value is 12 minutes.step is 30s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.8 |
hwMplsPsHoldOffThe time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.9 |
hwMplsPsSwitchConditionThe current switch condition of the protection group.
1: clear,This command clears all of the externally
initiated switch commands listed below;
2: lockout of protection,Fix the selector position on the
working LSP,Prevents the selector from switching to the
protection LSP when it is selecting the working LSP.
Switches the selector from the protection to the working LSP
when it is selecting the protection LSP;
3: forced protection,Switches the selector from the working LSP
to the protection LSP (unless a higher priority switch
request (i.e., LoP) is in effect);
4: signal fail,for 1:1,Signal Fail (SF) is declared when the
source of the protection domain enters the Defect State by
receiving a BDI packet (from the return LSP or out of band).
5: manual switch for working-lsp,Switches the selector from the
working LSP to the protection LSP (unless an equal or higher
priority switch request (i.e., LoP, FS, SF or MS) is in
effect);
6: manual switch for protection-lsp,Switches the selector from
the protection LSP to the working LSP (unless an equal or
higher priority switch request (i.e., LoP, FS, SF or MS) is
in effect).
7: WTR-timer;
8: HoldOff-timer;
9: Others;
The pripority of the commands are:
clear > lockout of protection > force switch > manual switch for working
lsp = manual switch for protection lsprw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.10 |
hwMplsPsWorkTunnelStateThe state of working tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defectro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.11 |
hwMplsPsProtTunnelStateThe state of protection tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defectro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.12 |
hwMplsPsSwitchResultWhich tunnel is used to transfer the data stream.
1: working-tunnel
2: protection-tunnelro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.13 |
hwMplsPsCfgTypeThe type of protection switch which is configured.
1: 1:1
2: 1+1
3: shared mesh
4: packet 1:1ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.14 |
hwMplsPsCfgProtectTunnIdProtect-tunnel id(session-tunnel-id).rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.15 |
hwMplsPsCfgRevertiveModeRevertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in a
non-revertive mode.
1: revertive;
2: non-revertive;rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.16 |
hwMplsPsCfgWTRWait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer has
expired.The default value is 12 minutes.step is 30s.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.17 |
hwMplsPsCfgHoldOffThe time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.18 |
hwMplsPsRowStatusThis variable is used to create, modify, and
delete a row in this table.
1: active
2: not in service
3: not ready
4: create and go
5: create and wait
6: destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.19 |
hwTunnPsTrapOpen1:enable;
2:disable;rw Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.3.2 |
hwMplsVCPsTableDescription. SEQUENCE OF HwMplsVCPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.3 |
hwMplsVCPsEntrythis table for these commands
1.mpls te protection tunnel XXX
2. mpls te reverse-lsp { lsp-name XXXX | lsr-id X.X.X.X tunnel-id x }
3. mpls te reserved-for-binding HwMplsVCPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.3.1 |
hwMplsVCPsIfIndexDescription.the index of working tunnel interface of Protection groupro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.1 |
hwMplsVCPsTNLBindingDescription.it is used by command ' mpls te reserved-for-binding 'rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.2 |
hwMplsTeReverseLspNameDescription.it is used for command ' mpls te reverse-lsp lspname'rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.3 |
hwMplsVcPsRowStatusDescription.
1: active;
2: notInservice;
3: notReady;
4: CreateAndGo;
5: CreateAndWait;
6: destroy;rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.4 |
hwMplsTeReverseLspLsrIdDescription.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'rw IpAddress .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.5 |
hwMplsTeReverseLspTunnIdDescription.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.6 |
hwMplsPsNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.4 |
hwMplsPsSwitchPtoWThis notification is generated when switching from
protection-lsp to working-lsp occured. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.1 |
hwMplsPsSwitchWtoPThis notification is generated when switching from woking-lsp
to protection-lsp occured. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.2 |
hwMplsOamPsConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100 |
hwMplsOamPsCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100.1 |
hwMplsOamPsGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100.2 |