HUAWEI-MPLSOAM-MIB
AI MIB Summary
The HUAWEI-MPLSOAM-MIB provides management objects for configuring and monitoring MPLS Operation, Administration, and Maintenance (OAM) functions on Huawei network devices, specifically enabling the administration of MPLS Label Switched Paths (LSPs) and associated fault detection mechanisms.
The HUAWEI-MPLSOAM-MIB contains objects to configure OAM module. The Operation, Administration and Maintenance (OAM) is an effective means for decreasing the cost of network maintenance. The MPLS OAM is used to administrate and maintain MPLS.
Main OID:
hwMplsOam.1.3.6.1.4.1.2011.5.12.7
163
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
163 total| Object Name |
|---|
hwMplsOamThe HUAWEI-MPLSOAM-MIB contains objects to configure OAM module.
The Operation, Administration and Maintenance (OAM)
is an effective means for decreasing the cost of network maintenance.
The MPLS OAM is used to administrate and maintain MPLS. MODULE-IDENTITY .1.3.6.1.4.1.2011.5.12.7 |
hwMplsOamPs OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1 |
hwMplsOamObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.1 |
hwMplsOamCapabilityWhether OAM is globally capable.
0: incapable;
1: capable;
2: capable(basedItu);
The default value is incapable.rw Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.1 |
hwMplsOamIgrTableThis table specifies per-LSP MPLS OAM capability and
associated information, such as IgrTunnName and IgrDetType. SEQUENCE OF HwMplsOamIgrEntry .1.3.6.1.4.1.2011.5.12.7.1.1.2 |
hwMplsOamIgrEntryAn entry in this table is created by an LSR for every LSP
capable of supporting MPLS OAM at ingress. HwMplsOamIgrEntry .1.3.6.1.4.1.2011.5.12.7.1.1.2.1 |
hwMplsOamIgrIndexThe interface index of the detected tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.1 |
hwMplsOamIgrTunnNameThe name of a tunnel.
For ingress, it means the tunnel name of the detected LSP.
For egress, it means the tunnel name of the reverse LSP.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.2 |
hwMplsOamIgrDetTypeThere are two types of OAM packets, CV and FFD.
The CV flow is generated at the source LSR of the LSP with
a nominal frequency of 1/s and terminated at the sink LSR of the LSP.
FFD provides failure detection option for an LSP independent
of the CV based availability model and is not tied to the
CV insertion rate. Insertion rates at 1/s or faster may
also be used.
The CV/FFD packet contains a network-unique identifier (TTSI)
so that all types of defects can be detected.
1: CV;
2: FFD.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.3 |
hwMplsOamIgrDetFreqFor CV: the frequency is static, per second.
For FFD: the frequency is set by user. The value
can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms.
Any other frequency is wrong.
0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: 3ms.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.4 |
hwMplsOamIgrRevTypeWhen an LSP is found to be in defect, the sink LSR if the LSP
should send BDI to inform the source LSR of the LSP, the BDI is
transferred through the reverse LSP.
The type of reverse LSP can be private or shared.
If private, then the reverse LSP can be used only when the only
LSP is in defect;
If shared, the reverse LSP which is shared between many forward
LSPs, whose source LSRs are the same and sink LSRs are the same.
1: private;
2: share.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.5 |
hwMplsOamIgrRevLspNameThe object indicates name of the reverse LSP.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.6 |
hwMplsOamIgrRevLsrIdOnly for ingress, the object indicates the ingress LSR ID of the
reverse LSP,, expressed in IP address.rw IpAddress .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.7 |
hwMplsOamIgrRevSessTunnIdOnly for ingress, the object indicates the session tunnel ID of
the reverse LSP.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.8 |
hwMplsOamIgrEnableWhether one LSP is OAM enable.
If disable, LSP is not monitored;
If enable, CV/FFD is generated at the source LSR of the LSP and
checked at the sink LSR of the LSP,and user can set
other configuration.
0: The OAM function is disabled on the ingress;
1: The OAM function is enabled on the ingress.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.9 |
hwMplsOamIgrValid0: stop detect;
1: start detect.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.10 |
hwMplsOamIgrAvaStateIf the LSP Timer (T1) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after the LSP Defect state
exists first.
T1 defines the length of time the LSP is in the Defect state
before declaring an LSP Unavailable or returning to defect
free state.
0: available state;
1: unavailable state.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.11 |
hwMplsOamIgrDefectTypeDefect is defined as interruption of the capability of a
transport entity (e.g., network connection) to transfer user
or OAM information. There are six types of defect:
0: no defect;
1: dServer;
2: dPeerMe;
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network..
8: dOamFail, AutoProtocal timer expires.
9: dIngressDown.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.12 |
hwMplsOamIgrRowStatusThis variable is used to create, modify, and
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.13 |
hwMplsOamIgrCompatibilityMode1: PtnMode;
2: RouterMode;
Valid only for the ingress configuration.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.14 |
hwMplsOamIgrBDIFreqBDI is generated at the trail termination source point of
a return path in response to a defect detected at the trail
termination sink point of an LSP in the forwarding direction.
The frequency of BDI can be set by user.
1: perSecond;
2: same as detect frequency.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.2.1.15 |
hwMplsOamEgrTableThis table specifies per-LSP MPLS OAM capability and
associated information, such as DetectType, DetectFrequency. SEQUENCE OF HwMplsOamEgrEntry .1.3.6.1.4.1.2011.5.12.7.1.1.3 |
hwMplsOamEgrEntryAn entry in this table is created by an LSR for every LSP
capable of supporting MPLS OAM at egress. HwMplsOamEgrEntry .1.3.6.1.4.1.2011.5.12.7.1.1.3.1 |
hwMplsOamEgrLspNameThe object indicates the name of static LSP at egress.ro OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.1 |
hwMplsOamEgrLsrIdThe object indicates the Ingress LSR ID of the LSP.ro IpAddress .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.2 |
hwMplsOamEgrSessTunnIdThe object indicates the the Ingress session tunnel ID of the LSP..ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.3 |
hwMplsOamEgrDetType0: invalid, if auto-protocol, this detect type is invalid;
1: CV;
2: FFD.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.4 |
hwMplsOamEgrDetFreq0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: invalid;
8: 3ms.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.5 |
hwMplsOamEgrRevTypeWhen an LSP is found to be in defect, the sink LSR of the LSP
should send BDI to inform the source LSR of the LSP,the BDI is
transferred through the reverse LSP.
The type of reverse LSP can be private or shared.
If private, then the reverse LSP can be used only when the only
LSP in defect;
If shared, the reverse LSP, which is shared between many forward
LSPs that have the same source LSRs and sink LSRs.
0: invalid, when the reverse LSR does not exist;
1: private;
2: share.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.6 |
hwMplsOamEgrRevTunnNameThe object indicates the name of a reverse tunnel.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.7 |
hwMplsOamEgrAutoEnIf autoprotocol, then the egress can process extended FDI sent
by ingress.
0: disable;
1: enable;
Valid only for the egress configuration.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.8 |
hwMplsOamEgrAutoOvertimeThis time is set at the egress.
If the egress receives CV/FFD, it records the parameters
included in the packet, such as OAM type and frequency.
If the egress does not receive any OAM packet before the timer
expires, the sink LSR will send BDI with dLOCV defect.
Valid only for the egress configuration.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.9 |
hwMplsOamEgrBDIFreqBDI is generated at the trail termination source point of
a return path in response to a defect detected at the trail
termination sink point of an LSP in the forwarding direction.
The frequency of BDI can be set by user.
Only valid for egress configuration.
The default value is detect frequency and it is valid only when a
backward-LSP exists.
0: perSecond;
1: same as detect frequency.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.10 |
hwMplsOamEgrEnableWhether one LSP is enabled with OAM.
If disable, LSP is not monitored;
If enable, CV/FFD is generated at the source LSR of the LSP and
checked at the sink LSR of the LSP, and user can set
other configuration.
0: The OAM function is disabled on the egress;
1: The OAM function is enabled on the egress.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.11 |
hwMplsOamEgrValid1: stop detect;
2: start detect.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.12 |
hwMplsOamEgrAvaStateIf the LSP Timer (T1) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after the LSP Defect State.
first exists.
T1 defines the length of time the LSP is in the Defect state
before declaring an LSP Unavailable or returning to defect
free state
0: available state;
1: unavailable state.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.13 |
hwMplsOamEgrDefectType0: no defect;
1: dServer,
2: dPeerMe,
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network.
8: dOamFail, AutoProtocal timer expires.
9: dEgressDown.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.14 |
hwMplsOamEgrRowStatusThis variable is used to create, modify, and
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.1.3.1.15 |
hwMplsOamRlsnTableThis table specifies RLSN capability and
associated information, such as RlsnLsrId and RlsnLsrId. SEQUENCE OF HwMplsOamRlsnEntry .1.3.6.1.4.1.2011.5.12.7.1.1.4 |
hwMplsOamRlsnEntryAn entry in this table is created by an LSR to binding the name, lsr-id and tunnel-id of the LSP at egress. HwMplsOamRlsnEntry .1.3.6.1.4.1.2011.5.12.7.1.1.4.1 |
hwMplsOamRlsnLspNameFor egress, the object indicates name of the LSP.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.1 |
hwMplsOamRlsnLsrIdFor egress, the object indicates the Ingress LSR ID of the LSPrw IpAddress .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.2 |
hwMplsOamRlsnSessTunnIdFor egress, the object indicates the Ingress session tunnel ID
of the LSPrw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.3 |
hwMplsOamRlsnIfIndexThe object indicates the index of outbound interface.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.4 |
hwMplsOamRlsnIfNameThe object indicates the name of outbound interface.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.5 |
hwMplsOamRlsnIsDown1: up
2: downro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.6 |
hwMplsOamRlsnRowStatusThis variable is used to create, modify, and
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.1.4.1.7 |
hwMplsOamViewCreate or delete the MPLS OAM view.
1: create mplsOam;
0: delete mplsOam;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.5 |
hwMplsOamL2vcTableThis table specifies PW MPLS OAM capability and
associated information, such as DetType and DetFrequence. SEQUENCE OF HwMplsOamL2vcEntry .1.3.6.1.4.1.2011.5.12.7.1.1.6 |
hwMplsOamL2vcEntryAn entry in this table is created by binding the peer-ip,
vc-type and vc-id. HwMplsOamL2vcEntry .1.3.6.1.4.1.2011.5.12.7.1.1.6.1 |
hwMplsOamL2vcPeerIpThis object indicates the peer ip address.ro IpAddress .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.1 |
hwMplsOamL2vcVcTypeThere are seventeen types of vc.
1: fr;
2: atmAal5Sdu;
3: atmTransCell;
4: vlan;
5: ethernet;
6: hdlc;
7: ppp;
9: atmNto1Vcc;
10:atmNto1Vpc;
11:ipLayer2;
12:atm1to1Vcc;
13:atm1to1Vpc;
14:atmAal5Pdu;
16:cep;
17:satopE1;
18:satopT1;
21:cesopsnBasic;
64:ipInterworking;
0:unknown.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.2 |
hwMplsOamL2vcVcIdThis object indicates the vc id of pw type.ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.3 |
hwMplsOamL2vcRemotePeerIpThis object indicates the remote peer ip address.rw IpAddress .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.4 |
hwMplsOamL2vcRemoteVcTypeThere are seventeen types of vc.
1: fr;
2: atmAal5Sdu;
3: atmTransCell;
4: vlan;
5: ethernet;
6: hdlc;
7: ppp;
9: atmNto1Vcc;
10:atmNto1Vpc;
11:ipLayer2;
12:atm1to1Vcc;
13:atm1to1Vpc;
14:atmAal5Pdu;
16:cep;
17:satopE1;
18:satopT1;
21:cesopsnBasic;
64:ipInterworking;
0:unknown.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.5 |
hwMplsOamL2vcRemoteVcIdThis object indicates the remote vc id of pw type.rw Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.6 |
hwMplsOamL2vcDetTypeThere are two types of OAM packets, CV and FFD.
1: CV;
2: FFD.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.7 |
hwMplsOamL2vcDetFreqFor CV: the frequency is static, per second.
For FFD: the frequency is set by user. The value
can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms.
Any other frequency is wrong.
0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: 3ms.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.8 |
hwMplsOamL2vcRevDetType0: invalid;
1: CV;
2: FFD.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.9 |
hwMplsOamL2vcRevDetFreqFor CV: the frequency is static, per second.
For FFD: the frequency is set by user. The value
can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms.
Any other frequency is wrong.
0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: invalid;
8: 3ms.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.10 |
hwMplsOamL2vcSendEnable0: The OAM Send function is Disabled;
1: The OAM Send function is Eabled;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.11 |
hwMplsOamL2vcReceiveEnable0: The OAM Receive function is Disabled;
1: The OAM Receive function is Eabled;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.12 |
hwMplsOamL2vcAutoProlEn0: disable;
1: enable;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.13 |
hwMplsOamL2vcAutoOvertimeIf the oam receives CV/FFD, it records the parameters
included in the packet, such as OAM type and frequency.
If the oam does not receive any CV/FFD packet before the timer
expires, It will send BDI with dLOCV defect.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.14 |
hwMplsOamL2vcValid1: stop detect;
2: start detect;
3: ready.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.15 |
hwMplsOamL2vcAvaState0: available state;
1: unavailable state.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.16 |
hwMplsOamL2vcDefectType0: no defect;
1: dServer,
2: dPeerMe,
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network.
8: dOamFail, AutoProtocal timer expires.
9: pwDown, PW down.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.17 |
hwMplsOamL2vcBdiDefectType0: no defect;
1: dServer,
2: dPeerMe,
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network.
8: dOamFail, AutoProtocal timer expires.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.18 |
hwMplsOamL2vcRowStatusThis variable is used to create, modify, and
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.30 |
hwMplsOamL2vcCompatibilityMode1: ptnMode;
2: routerMode;
Valid only for the l2vc configuration.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.31 |
hwMplsOamL2vcBDIFreqBDI is generated at the trail termination source point of
a return path in response to a defect detected at the trail
termination sink point of an LSP in the forwarding direction.
The frequency of BDI can be set by user.
1: perSecond;
2: same as detect frequency.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.6.1.32 |
hwMplsOamBidirectionalTunnelTableThis table specifies Static Co-Route MPLS OAM capability and
associated information, such as DetType and DetFrequence. SEQUENCE OF HwMplsOamBidirectionalTunnelEntry .1.3.6.1.4.1.2011.5.12.7.1.1.7 |
hwMplsOamBidirectionalTunnelEntryAn entry in this table is created by binding the tunnel ifindex. HwMplsOamBidirectionalTunnelEntry .1.3.6.1.4.1.2011.5.12.7.1.1.7.1 |
hwMplsOamBidirectionalTunnelIndexThis is a unique index for an OAM entry in the OAM table.ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.1 |
hwMplsOamBidirectionalTunnelTunnNameThe name of a tunnel.rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.2 |
hwMplsOamBidirectionalTunnelDetTypeThere are two types of OAM packets, CV and FFD.
1: CV;
2: FFD.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.3 |
hwMplsOamBidirectionalTunnelDetFreqFor CV: the frequency is static, per second.
For FFD: the frequency is set by user. The value
can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms.
Any other frequency is wrong.
0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: 3ms.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.4 |
hwMplsOamBidirectionalTunnelRevDetType0: invalid;
1: CV;
2: FFD.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.5 |
hwMplsOamBidirectionalTunnelRevDetFreqFor CV: the frequency is static, per second.
For FFD: the frequency is set by user. The value
can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms.
Any other frequency is wrong.
0: 1000ms(only for cv);
1: 10ms;
2: 20ms;
3: 50ms;
4: 100ms;
5: 200ms;
6: 500ms;
7: invalid;
8: 3ms.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.6 |
hwMplsOamBidirectionalTunnelSendEnable0: The OAM Send function is Disabled;
1: The OAM Send function is Eabled;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.7 |
hwMplsOamBidirectionalTunnelReceiveEnable0: The OAM Receive function is Disabled;
1: The OAM Receive function is Eabled;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.8 |
hwMplsOamBidirectionalTunnelAutoProtocolEnable0: disable;
1: enable;rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.9 |
hwMplsOamBidirectionalTunnelAutoOvertimeIf the oam receives CV/FFD, it records the parameters
included in the packet, such as OAM type and frequency.
If the oam does not receive any CV/FFD packet before the timer
expires, It will send BDI with dLOCV defect.rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.10 |
hwMplsOamBidirectionalTunnelValid1: stop detect;
2: start detect;
3: ready.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.11 |
hwMplsOamBidirectionalTunnelAvaState0: available state;
1: unavailable state.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.12 |
hwMplsOamBidirectionalTunnelDefectType0: no defect;
1: dServer,
2: dPeerMe,
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network.
8: dOamFail, AutoProtocal timer expires.
9: corouteDown, coroute down.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.13 |
hwMplsOamBidirectionalTunnelBdiDefectType0: no defect;
1: dServer,
2: dPeerMe,
3: dLOCV, Loss of Connectivity Verification defect;
4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect;
5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.;
6: dExcess, Receiving excess rate of CV/FFD;
7: dUnknown, Unknown defect in the MPLS network.
8: dOamFail, AutoProtocal timer expires.ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.14 |
hwMplsOamBidirectionalTunnelRowStatusThis variable is used to create, modify, and
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.15 |
hwMplsOamBidirectionalTunnelCompatibilityMode1: ptnMode;
2: routerMode;
Valid only for the bidirectional tunnel configuration.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.16 |
hwMplsOamBidirectionalTunnelBDIFreqBDI is generated at the trail termination source point of
a return path in response to a defect detected at the trail
termination sink point of an LSP in the forwarding direction.
The frequency of BDI can be set by user.
1: perSecond;
2: same as detect frequency.rw Enumeration .1.3.6.1.4.1.2011.5.12.7.1.1.7.1.17 |
hwMplsOamTrapOpen0: disable
1: enablerw Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.1.8 |
hwMplsOamNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.2 |
hwMplsOamIgrLSPOutDefectThis notification is generated when the LSP is found
not in the defect state at the LSP ingress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.1 |
hwMplsOamIgrLSPInDefectThis notification is generated when the LSP is found
in the defect state at the LSP ingress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.2 |
hwMplsOamIgrLSPAvaThis notification is generated when the LSP is found
in the available state at the LSP ingress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.3 |
hwMplsOamIgrLSPUnAvaThis notification is generated when the LSP is found
in the unavailable state at the LSP ingress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.4 |
hwMplsOamEgrLSPOutDefectThis notification is generated when the LSP is found
not in the defect state at the LSP egress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.5 |
hwMplsOamEgrLSPInDefectThis notification is generated when the LSP is found
in the defect state at the LSP egress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.6 |
hwMplsOamEgrLSPAvaThis notification is generated when the LSP is found
in the available state at the LSP egress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.7 |
hwMplsOamEgrLSPUnAvaThis notification is generated when the LSP is found
in the unavailable state at the LSP egress. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.8 |
hwMplsOamEgrFirstPktIf autoprotocol is enabled, this notification is generated when
egress receives the first CV/FFD packet. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.9 |
hwMplsOamEgrAutoProFDIThe FDI packet is used by the upstream node in an LSP
to inform the egress of the defect information.
It is also generated when the auto protocol is enabled,
with which the LSP ingress notifies the egress to stop
the OAM detection. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.10 |
hwMplsOamEgrRlsnDownThis notification is generated when the Rlsn is down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.11 |
hwMplsOamL2vcOutDefectThis notification is generated when the PW is found
not in the defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.12 |
hwMplsOamL2vcInDefectThis notification is generated when the PW is found
not in the defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.13 |
hwMplsOamL2vcAvaThis notification is generated when the PW is found
in the unavailable state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.14 |
hwMplsOamL2vcUnAvaThis notification is generated when the PW is found
in the unavailable state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.15 |
hwMplsOamBidirectionalTunnelOutDefectThis notification is generated when the CO-ROUTE is found
not in the defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.16 |
hwMplsOamBidirectionalTunnelInDefectThis notification is generated when the CO-ROUTE is found
not in the defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.17 |
hwMplsOamBidirectionalTunnelAvaThis notification is generated when the CO-ROUTE is found
in the unavailable state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.18 |
hwMplsOamBidirectionalTunnelUnAvaThis notification is generated when the CO-ROUTE is found
in the unavailable state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.2.19 |
hwMplsPsObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.3 |
hwMplsPsTableThis table specifies per-protection-group MPLS PS
capability and associated information. SEQUENCE OF HwMplsPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.1 |
hwMplsPsEntryAn entry in this table is created by an LSR for every
protection group capable of supporting mpls ps. HwMplsPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.1.1 |
hwMplsPsIndexThis is a unique index for an entry in the mplspsEntry.ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.1 |
hwMplsPsTypeThe type of protection switch,can be 1:1,1+1,shared mesh,
packet 1+1,the default choice is 1:1.
In the 1+1 architecture type, a protection LSP is dedicated to
each working LSP with the working LSP bridged onto the
protection LSP at the source of the protection domain.
The traffic on working and protection LSPs is transmitted
simultaneously to the sink of the protection domain,
where a selection between the working and protection LSP is
made, based on some predetermined criteria, such as defect
indication.
In the 1:1 architecture type, a protection LSP is dedicated to
each working LSP. The working traffic is transmitted either by
working or protection LSP.
In the shared mesh architecture type, possible sharing of
protection capacity between disjoint link, node in the network
is achieved while guaranteeing recovery from a single failure.
In the packet 1+1 architecture type, the traffic is transmitted
simultaneously onto two possibly disjoint routed LSPs to the
sink of the protection domain. Each pair of duplicate
transmitted packets is assigned the same identifier (sequence
number) but distinct from the other pairs of duplicate packets.
At the sink of the protection domain packet level selection
mechanism is employed to select one of the two possibly
received copies of each packet.
1: 1:1 protection switching,;
2: 1+1 protection switching;
3: shared mesh protection swiching;
4: packet 1+1 protection switching.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.2 |
hwMplsPsWorkTunnNameThe name of work-tunnel.ro OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3 |
hwMplsPsWorkTunnIdWork-tunnel id(session-tunnel-id).ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.4 |
hwMplsPsProtectTunnNameThe name of protect-tunnel.ro OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.5 |
hwMplsPsProtectTunnIdProtect-tunnel id(session-tunnel-id).ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.6 |
hwMplsPsRevertiveModeRevertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in a
non-revertive mode.
1: revertive;
2: non-revertive;ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.7 |
hwMplsPsWTRWait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer has
expired.The default value is 12 minutes.step is 30s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.8 |
hwMplsPsHoldOffThe time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.9 |
hwMplsPsSwitchConditionThe current switch condition of the protection group.
1: clear,This command clears all of the externally
initiated switch commands listed below;
2: lockout of protection,Fix the selector position on the
working LSP,Prevents the selector from switching to the
protection LSP when it is selecting the working LSP.
Switches the selector from the protection to the working LSP
when it is selecting the protection LSP;
3: forced protection,Switches the selector from the working LSP
to the protection LSP (unless a higher priority switch
request (i.e., LoP) is in effect);
4: signal fail,for 1:1,Signal Fail (SF) is declared when the
source of the protection domain enters the Defect State by
receiving a BDI packet (from the return LSP or out of band).
5: manual switch for working-lsp,Switches the selector from the
working LSP to the protection LSP (unless an equal or higher
priority switch request (i.e., LoP, FS, SF or MS) is in
effect);
6: manual switch for protection-lsp,Switches the selector from
the protection LSP to the working LSP (unless an equal or
higher priority switch request (i.e., LoP, FS, SF or MS) is
in effect).
7: WTR-timer;
8: HoldOff-timer;
9: Others;
The pripority of the commands are:
clear > lockout of protection > force switch > manual switch for working
lsp = manual switch for protection lspro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.10 |
hwMplsPsWorkTunnelStateThe state of working tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defectro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.11 |
hwMplsPsProtTunnelStateThe state of protection tunnel state in one protection group,
whether it is in detection,
1: it is outof defect
2: it enters defectro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.12 |
hwMplsPsSwitchResultWhich tunnel is used to transfer the data stream.
1: working-tunnel
2: protection-tunnelro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.13 |
hwMplsPsCfgTypeThe type of protection switch which is configured.
1: 1:1
2: 1+1
3: shared mesh
4: packet 1:1ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.14 |
hwMplsPsCfgProtectTunnIdProtect-tunnel id(session-tunnel-id).ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.15 |
hwMplsPsCfgRevertiveModeRevertive mode is a protection switching mode where revertive
action (switch back to the working LSP) is taken after the
working LSP is repaired.And switching does not occur in a
non-revertive mode.
1: revertive;
2: non-revertive;ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.16 |
hwMplsPsCfgWTRWait to Restore timer is only applicable for the revertive mode
and applies to a working LSP,It prevents reversion back to
select the working LSP until the Wait to Restore timer has
expired.The default value is 12 minutes.step is 30s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.17 |
hwMplsPsCfgHoldOffThe time between declaration of signal degrade or signal fail,
and the initialization of the protection switching algorithm.
step is 100ms.maximum is 10s.ro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.18 |
hwMplsPsRowStatusThis variable is used to create, modify, and
delete a row in this table.
1: active
2: not in service
3: not ready
4: create and go
5: create and wait
6: destroyrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.19 |
hwMplsPsLocalStateThe current local state of the protection group.
0: Lockout of Protection (LO)
1: Signal Fail for Protection (SF-P)
2: Forced Switch (FS)
3: Signal Fail for Working (SF)
4: Signal Degrade for Protection(SD-P)
5: Signal Degrade for Working(SD)
6: Manual Switch (MS)
7: Wait-to-Restore (WTR)
8: Exercise (EXER)
9: Reverse Request(RR)
10: Do Not Revert (DNR)
11: No Request (NR)
The pripority of the commands are:
LO > SF-P > FS > SF > SD-P > SD > MS > WTR > EXER > RR > DNR > NRro Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.1.1.20 |
hwTunnPsTrapOpen1:enable;
2:disable;ro Unsigned32 .1.3.6.1.4.1.2011.5.12.7.1.3.2 |
hwMplsVCPsTableDescription. SEQUENCE OF HwMplsVCPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.3 |
hwMplsVCPsEntrythis table for these commands
1.mpls te protection tunnel XXX
2. mpls te reverse-lsp { lsp-name XXXX | lsr-id X.X.X.X tunnel-id x }
3. mpls te reserved-for-binding HwMplsVCPsEntry .1.3.6.1.4.1.2011.5.12.7.1.3.3.1 |
hwMplsVCPsIfIndexDescription.the index of working tunnel interface of Protection groupro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.1 |
hwMplsVCPsTNLBindingDescription.it is used by command ' mpls te reserved-for-binding 'rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.2 |
hwMplsTeReverseLspNameDescription.it is used for command ' mpls te reverse-lsp lspname'rw OCTET STRING .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.3 |
hwMplsVcPsRowStatusDescription.
1: active;
2: notInservice;
3: notReady;
4: CreateAndGo;
5: CreateAndWait;
6: destroy;rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.4 |
hwMplsTeReverseLspLsrIdDescription.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'rw IpAddress .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.5 |
hwMplsTeReverseLspTunnIdDescription.it is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX'rw Integer32 .1.3.6.1.4.1.2011.5.12.7.1.3.3.1.6 |
hwMplsApsMismatchReasonIndicates the alarm reason as below:
1. Bridge type mismatch, one side is 1:1 (Selector Bridge) protection,
the other side is 1+1 (Permanent Bridge) protection;
2. Channel type mismatch, one side has APS channel, the other side has no APS channel;
3. Switching type mismatch, one side is bidirectional switching,
the other side is unidirectional switching;
4. Operation type mismatch, one side is revertive operation,
the other side is non-revertive operation;
5. Traffic request mismatch, one side selects working connection,
the other side selects protection connection;ro Enumeration .1.3.6.1.4.1.2011.5.12.7.1.3.4 |
hwMplsPsNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.4 |
hwMplsPsSwitchPtoWThis notification is generated when switching from
protection-lsp to working-lsp occured. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.1 |
hwMplsPsSwitchWtoPThis notification is generated when switching from woking-lsp
to protection-lsp occured. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.2 |
hwMplsApsMismatchTrap information indicates fully incompatible provisioning and
working/protection configuration mismatch are detected by APS frame. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.3 |
hwMplsApsMismatchRecoveryTrap information indicates fully incompatible provisioning and
working/protection configuration mismatch recovery are detected by APS frame. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.4 |
hwMplsApsLostTunnel protection group did not receive APS frames from protection tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.5 |
hwMplsApsLostRecoveryTunnel protection group received APS frames from protection tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.6 |
hwMplsApsOutageTunnel protection group changed to defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.7 |
hwMplsApsOutageRecoveryTunnel protection group recovered from defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.8 |
hwMplsApsDegradedProtection tunnel changed to defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.9 |
hwMplsApsDegradedRecoveryProtection tunnel recovered from defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.10 |
hwMplsApsSwitchFailTunnel protection group changed to defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.11 |
hwMplsApsSwitchFailRecoveryTunnel protection group recovered from defect state. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.12.7.1.4.12 |
hwMplsOamPsConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100 |
hwMplsOamPsCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100.1 |
hwMplsOamPsGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.100.2 |
hwMplsOamObjectConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.101 |
hwMplsOamObjectGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.101.1 |
hwMplsOamObjectCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.12.7.1.101.2 |