HUAWEI-MPLS-EXTEND-MIB
AI MIB Summary
The HUAWEI-MPLS-EXTEND-MIB module extends standard MPLS monitoring on Huawei network devices by exposing vendor-specific private objects and trap definitions for granular visibility into MPLS label switching operations. It enables the collection of proprietary performance metrics and the reception of critical fault notifications for Huawei-specific MPLS implementations not covered by IETF standards.
This MIB is used for defining the HUAWEI private extended Multiprotocol Label Switching (MPLS) MIB object. All MIB objects are used to describe private managed objects and trap definitions for MPLS.
Main OID:
hwMplsExtendMib.1.3.6.1.4.1.2011.5.25.121
282
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
282 total| Object Name |
|---|
hwMplsExtendMibThis MIB is used for defining the HUAWEI private
extended Multiprotocol Label Switching (MPLS) MIB
object. All MIB objects are used to describe private
managed objects and trap definitions for MPLS. MODULE-IDENTITY .1.3.6.1.4.1.2011.5.25.121 |
hwMplsExtendMibTunnel OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.1 |
hwMplsTunnelTableA tunnel needs to be uniquely identified across
an MPLS network. Indexes hwMplsTunnelIndex and
hwMplsTunnelInstance uniquely identify a tunnel
on the LSR originating the tunnel.
hwMplsTunnelIngressLSRId uniquely identifies a
tunnel across an MPLS network. The last index
hwMplsTunnelEgressLSRId is useful in identifying
all instances of a tunnel that are terminated on
the same egress LSR.
The indexes of this table are hwMplsTunnelIndex,
hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and
hwMplsTunnelEgressLSRId. SEQUENCE OF HwMplsTunnelEntry .1.3.6.1.4.1.2011.5.25.121.1.1 |
hwMplsTunnelEntryA tunnel needs to be uniquely identified across
an MPLS network. Indexes hwMplsTunnelIndex and
hwMplsTunnelInstance uniquely identify a tunnel
on the LSR originating the tunnel.
hwMplsTunnelIngressLSRId uniquely identifies a
tunnel across an MPLS network. The last index
hwMplsTunnelEgressLSRId is useful in identifying
all instances of a tunnel that are terminated on
the same egress LSR.
The indexes of this entry are hwMplsTunnelIndex,
hwMplsTunnelInstance, hwMplsTunnelIngressLSRId and
hwMplsTunnelEgressLSRId. HwMplsTunnelEntry .1.3.6.1.4.1.2011.5.25.121.1.1.1 |
hwMplsTunnelIndexUniquely identifies a set of tunnel instances
between a pair of ingress and egress LSRs.
When the MPLS signalling protocol is rsvp(2), this value
equals to the value signaled in the Tunnel ID
of the SESSION object. When the MPLS signalling protocol
is crldp(3), this value equals to the value
signaled in the LSP ID. Reference to MPLS-TE-STD-MIB. MplsTunnelIndex (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.1 |
hwMplsTunnelInstanceUniquely identifies a particular instance of a
tunnel between a pair of ingress and egress LSRs.
It is used to identify multiple instances of
tunnels for backup and parallel tunnels.
When the MPLS signaling protocol is
rsvp(2), this value equals to the LSP ID
of the Sender Template object. When the signaling
protocol is crldp(3) there is no equivalent
signaling object. Reference to MPLS-TE-STD-MIB. MplsTunnelInstanceIndex (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.2 |
hwMplsTunnelIngressLSRIdIndicates the ingress LSR ID of this tunnel.
When the MPLS signalling protocol
is rsvp(2), this value equals to the Tunnel
Sender Address in the Sender Template object and may
equal to the Extended Tunnel ID in the
SESSION object. When the MPLS signalling protocol is
crldp(3), this value equals to the Ingress
LSR Router ID in the LSPID TLV object.
Reference to MPLS-TE-STD-MIB. MplsExtendedTunnelId (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.3 |
hwMplsTunnelEgressLSRIdIndicates the egress LSR ID of this
tunnel. Reference to MPLS-TE-STD-MIB. MplsExtendedTunnelId (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.4 |
hwMplsTunnelClassTypeIndicates the bandwidth type used by this tunnel.
Options:
1. bc0(1) -indicates the bandwidth type is bc0.
2. bc1(2) -indicates the bandwidth type is bc1.
3. invalidValue(3) -indicates the invalid value.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.5 |
hwMplsTunnelBandwidthIndicates the bandwidth used by this tunnel.
Unit: kbit/sro Integer32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.6 |
hwMplsTunnelAdminStatusIndicates the management status of this
tunnel.Reference to MPLS-TE-STD-MIB.
Options:
1. up(1) -indicates the management status of this tunnel is up.
2. down(2) -indicates the management status of this tunnel is down.
3. testing(3) -indicates the tunnel is used in some test mode.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.7 |
hwMplsTunnelOperStatusIndicates the actual operational status of this tunnel,
which is but not limited to the status of this tunnel of
a certain period.Reference to MPLS-TE-STD-MIB.
Options:
1. up(1) -indicates that the operational status of this tunnel is up.
2. down(2) -indicates that the operational status of this tunnel is down.
3. testing(3) -indicates that the tunnel is used in some test mode.
4. unknown(4) -indicates the invalid value.
5. dormant(5) -indicates that the status cannot be determined.
6. notPresent(6) -indicates that some component is missing
7. lowerLayerDown(7) -indicates the Down state due to the state of lower layer interfaces.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.8 |
hwMplsTunnelSessionAttrIndicates protection types desired by the primary
tunnel, such as node protection, link protection or
bandwidth protection.
Options:
1. localProtectionDesired(0) -indicates link protection.
2. nodeProtectionDesired(1) -indicates node protection.
3. bandwidthProtectionDesired(2) -indicates bandwidth protection.ro Bits .1.3.6.1.4.1.2011.5.25.121.1.1.1.9 |
hwMplsTunnelFrrSetupPrioIndicates the setup PRI of auto-bypass tunnel.
Range: 0-7
Default: 7ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.10 |
hwMplsTunnelFrrHoldingPrioIndicates the holding PRI of auto-bypass tunnel.
Range: 0-7
Default: 7ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.11 |
hwMplsTunnelFrrBandwidthIndicates the protecting bandwidth of auto-bypass tunnel.
Its value is defined by the configuration on the primary
tunnel.
Unit: kbit/sro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.12 |
hwMplsTunnelFrrSwitchoverIndicates FRR switching timesro Counter32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.13 |
hwMplsTunnelFrrBypassTableIndexIndicates the index of the bypass tunnel table, that is,
the LSP ID of the bypass tunnel. The bypass table shows
interfaces protected by specified bypass tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.14 |
hwMplsTunnelFrrARHopTableIndexIndicates the table index of the protection type adopted
by each hop of the primary tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.15 |
hwMplsTunnelNameIndicates the tunnel name. The name can refer to the tunnel
on the console port of the LSR. If mplsTunnelIsIf is set to
True, the IfName of the interface corresponding to this tunnel
should have a value equal to hwMplsTunnelName.
Reference to the description of IfName in RFC 2863.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.16 |
hwMplsTunnelIfIndexIndicates the interface index of the tunnel. It uniquely
identifies the tunnel name.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.17 |
hwMplsTunnelPreBandwidthIndicates the original bandwidth of the tunnel
when the tunnel is in the Modify state.
Unit: kbit/sro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.18 |
hwMplsTunnelNextBandwidthIndicates the bandwidth of the tunnel that is to be changed
when the tunnel is in the Modify state.
Unit: kbit/sro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.1.1.19 |
hwMplsTunnelCt0BandwidthThe bandwidth of Class-Type 0 (CT0) in this tunnel, in kbit/s.
If all CT bandwidths are 0s, it means that this tunnel's Class-Type
is CT0, and bandwidth is 0 kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.20 |
hwMplsTunnelCt1BandwidthThe bandwidth of Class-Type 1 (CT1) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.21 |
hwMplsTunnelCt2BandwidthThe bandwidth of Class-Type 2 (CT2) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.22 |
hwMplsTunnelCt3BandwidthThe bandwidth of Class-Type 3 (CT3) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.23 |
hwMplsTunnelCt4BandwidthThe bandwidth of Class-Type 4 (CT4) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.24 |
hwMplsTunnelCt5BandwidthThe bandwidth of Class-Type 5 (CT5) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.25 |
hwMplsTunnelCt6BandwidthThe bandwidth of Class-Type 6 (CT6) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.26 |
hwMplsTunnelCt7BandwidthThe bandwidth of Class-Type 7 (CT7) in this tunnel, in kbit/s.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.1.1.27 |
hwMplsTunnelLspTypeThis object is meaningful only at the ingress of the tunnel. It indicates LSP types.
Options:
0. invalid(0) -indicates that the LSP type is invalid, the possible cause is that the LSP is not created at an ingress.
1. primary(1) -indicates the primary LSP
2. primaryModifing(2) -indicates the LSP that will replace the primary LSP
3. hotStandby(3) -indicates the hot-standby LSP
4. hotStandbyModifing(4) -indicates the LSP that will replace the hot-standby LSP
5. ordinary(5) -indicates the ordinary LSP
6. ordinaryModifing(6) -indicates the LSP that will replace the ordinary LSP
7. bestEffort(7) -indicates the Best-Effort LSP
8. bestEffortModifing(8) -indicates the LSP that will replace the Best-Effort LSP
Modifying LSPs are created when users modify the make-before-break attribute of the corresponding LSP types. After being created, modifying LSPs replace the corresponding LSPs to transmit traffic.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.28 |
hwMplsTunnelInterfaceNameIndicates the tunnel interface name. The object is
only valid at the ingress.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.1.1.1.29 |
hwMplsTunnelSignalProtoIndicates the signal protocol of this tunnelro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.30 |
hwMplsTunnelTypeThis object is meaningful only at the ingress of the tunnel. It indicates tunnel types.
Options:
1. invalid(1) -indicates that the tunnel type is invalid, the possible cause is that it is not ingress node of this tunnel
2. primaryTunnel(2) -indicates that this is a primary tunnel
3. bypassTunnel(3) -indicates that this is a bypass tunnelro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.1.1.31 |
hwTunnelFrrBypassTableIndicates the bypass tunnel. The indexes of this table are
hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. SEQUENCE OF HwTunnelFrrBypassEntry .1.3.6.1.4.1.2011.5.25.121.1.2 |
hwTunnelFrrBypassEntryIndicates the bypass tunnel.The indexes of this entry are
hwTunnelFrrBypassListIndex and hwTunnelFrrBypassIndex. HwTunnelFrrBypassEntry .1.3.6.1.4.1.2011.5.25.121.1.2.1 |
hwTunnelFrrBypassListIndexIndicates the index of the bypass tunnel table, that is, the LSP ID of the bypass tunnel. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.2.1.1 |
hwTunnelFrrBypassIndexIndicates the index of the bypass tunnel interface. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.2.1.2 |
hwTunnelFrrBypassProtIfIndexIndicates the index of the interface protected by the bypass tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.2.1.3 |
hwTunnelFrrARHopTableIndicates the FrrARHopTable, which will show every hop's frr
protect information of the tunnel.
The indexes of this table are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex. SEQUENCE OF HwTunnelFrrARHopEntry .1.3.6.1.4.1.2011.5.25.121.1.3 |
hwTunnelFrrARHopEntryIndicates the FrrARHopTable, which will show every hop's frr
protect information of the tunnel.
The indexes of this entry are hwTunnelFrrARHopListIndex and hwTunnelFrrARHopIndex. HwTunnelFrrARHopEntry .1.3.6.1.4.1.2011.5.25.121.1.3.1 |
hwTunnelFrrARHopListIndexIndicates the table index of each hop along the primary tunnel. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.3.1.1 |
hwTunnelFrrARHopIndexIndicates the index of each hop along the primary tunnel. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.3.1.2 |
hwTunnelFrrARHopProtDesiredIndicates the FRR protection types desired by the primary tunnel interface, including:
0: link protection,
1: node protection,
2: bandwidth protectionro Bits .1.3.6.1.4.1.2011.5.25.121.1.3.1.3 |
hwTunnelFrrARHopProtActualIndicates the actual FRR protection types of the primary tunnel interface, including:
0: link protection,
1: node protection,
2: bandwidth protection,
3: primary tunnel protection in usero Bits .1.3.6.1.4.1.2011.5.25.121.1.3.1.4 |
hwTunnelFrrRouteDBTableIndicates the primary tunnel is protected by which bypass tunnel. The indexes of this
table are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance,
hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId. SEQUENCE OF HwTunnelFrrRouteDBEntry .1.3.6.1.4.1.2011.5.25.121.1.4 |
hwTunnelFrrRouteDBEntryIndicates the primary tunnel is protected by which bypass tunnel. The indexes of this
entry are hwTunnelFrrRouteDBTunnelIndex, hwTunnelFrrRouteDBTunnelInstance,
hwTunnelFrrRouteDBTunnelIngressLSRId and hwTunnelFrrRouteDBTunnelEngressLSRId. HwTunnelFrrRouteDBEntry .1.3.6.1.4.1.2011.5.25.121.1.4.1 |
hwTunnelFrrRouteDBTunnelIndexIdentifies the index of the primary. Manager obtains new index
values for row creation in this table by reading mplsTunnelIndexNext.
When the MPLS signaling protocol is rsvp(2), this value equals to
the value signaled in the Tunnel ID of the SESSION object. When
the MPLS signaling protocol is crldp(3), this value equals to the
value signaled in the LSP ID. Reference to MPLS-TE-STD-MIB. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.1 |
hwTunnelFrrRouteDBTunnelInstanceUniquely identifies a particular instance of a
tunnel between a pair of ingress and egress LSRs.
It is the object identifies multiple instances of
tunnels for the purposes of backup and parallel
tunnels. When the MPLS signaling protocol is
rsvp(2), this value equals to the LSP ID
of the Sender Template object. When the signaling
protocol is crldp(3), there is no equivalent
signaling object. Reference to MPLS-TE-STD-MIB. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.2 |
hwTunnelFrrRouteDBTunnelIngressLSRIdIdentifies the ingress LSR ID of the primary tunnel.
When the MPLS signalling protocol is rsvp(2),LSR ID
equals to the Tunnel Sender Address in the Sender
Template object or the Extended Tunnel Id in the
SESSION object. When the MPLS signalling protocol is
crldp(3), LSR ID equals to the Ingress
LSR Router ID in the LSPID TLV object. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.3 |
hwTunnelFrrRouteDBTunnelEngressLSRIdIdentifies the egress LSR ID of the primary tunnel.
Reference to MPLS-TE-STD-MIB. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.4 |
hwTunnelFrrRouteDBBypassIfIndexIndicates the interface index of the bypass tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.5 |
hwTunnelFrrRouteDBInnerLabelIndicates the inner label of the primary tunnel and bypass tunnel.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.4.1.6 |
hwStaticLspTableA static LSP is created by a network administrator by using
static MPLS. Note that only point-to-point static LSP segments
are supported. Each static MPLS LSP can thus have one out-segment
originating at this LSR and/or one in-segment terminating at
this LSR. The indexes of this table are hwStaticLspIndex,
hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex. SEQUENCE OF HwStaticLspEntry .1.3.6.1.4.1.2011.5.25.121.1.5 |
hwStaticLspEntryA static LSP is created by a network administrator by using
static MPLS. Note that only point-to-point static LSP segments
are supported. Each static MPLS LSP can thus have one out-segment
originating at this LSR and/or one in-segment terminating at
this LSR. The indexes of this entry are hwStaticLspIndex,
hwStaticLspInSegmentIndex, and hwStaticLspOutSegmentIndex. HwStaticLspEntry .1.3.6.1.4.1.2011.5.25.121.1.5.1 |
hwStaticLspIndexIndicates the index of the static LSP. If the string is 0x00,
it means that the index is invalid. MplsIndexType (MPLS-LSR-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.5.1.1 |
hwStaticLspInSegmentIndexIndicates the incoming label index of the static LSP/CR-LSP.
If the string is 0x00, it means that the index is invalid.
In this case, no corresponding mplsInSegmentEntry exists.
Reference to MPLS-LSR-STD-MIB. MplsIndexType (MPLS-LSR-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.5.1.2 |
hwStaticLspOutSegmentIndexIndicates the outgoing index of the static LSP/CR-LSP.
If the entry is used to identify the incoming node or
intermediate node of the LSP, this object cannot be set
to the string 0x00. Because corresponding mplsOutSegmentEntry
exists. If the entry is used to identify the outgoing node
of the LSP, this object must be set to the string 0x00. Because
no corresponding mplsOutSegmentEntry exists.
Reference to MPLS-LSR-STD-MIB. MplsIndexType (MPLS-LSR-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.1.5.1.3 |
hwStaticLspOwnerDenotes the entity that creates and manages the static LSP. See MPLS-LSR-STD-MIB.
Options:
1. static(1) -indicates the static LSP.
2. crstatic(2) -indicates the static CR-LSP.
3. other(3) -indicates the LSP of another type.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.5.1.4 |
hwStaticLspNameIndicates the name of the static LSP or CR-LSP.
The name is appointed when the static LSP or CR-LSP
is created.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.1.5.1.5 |
hwStaticLspStatusIndicates the actual operation status of the static LSP/CR-LSP.
Options:
1. up(1) -indicates that the static LSP/CR-LSP is in Up state.
2. down(2) -indicates that the static LSP/CR-LSP is in down state.
3. testing(3) -indicates that the static LSP/CR-LSP is used in test mode.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.5.1.6 |
hwStaticLspClassTypeThe Class-Type of this static lsp.
Options:
1. ct0(1) -indicates that the class type is ct0.
2. ct1(2) -indicates that the class type is ct1.
3. ct2(3) -indicates that the class type is ct2.
4. ct3(4) -indicates that the class type is ct3.
5. ct4(5) -indicates that the class type is ct4.
6. ct5(6) -indicates that the class type is ct5.
7. ct6(7) -indicates that the class type is ct6.
8. ct7(8) -indicates that the class type is ct7.
9. none(9) -indicates that the class type is unconfiged.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.5.1.7 |
hwStaticLspBandwidthThe bandwidth of this static lsp.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.5.1.8 |
hwMplsTeClassTableTE-class mapping is a set of a maximum of eight TE-class items.
TE-class is a <Class-Type, Priority> pair, such as TE-Class[1] = <CT0, 5>.
A (setup/holding) priority associated with an LSP valid only if it appears
as a pair with the Class-Type. Class-Types and priorities can be randomly
paired up. You can define a maximum of eight <Class-Type, Priority> pairs.
The LSR is considered to support a particular Class-Type only if it appears
in the definition of the eight possible TE-Classes. It is suggested that all
the LSRs in the domain use the same TE-Class mapping. The index of this table
is hwMplsTeClassId. SEQUENCE OF HwMplsTeClassEntry .1.3.6.1.4.1.2011.5.25.121.1.6 |
hwMplsTeClassEntryTE-class mapping is a set of a maximum of eight TE-class items.
TE-class is a <Class-Type, Priority> pair, such as TE-Class[1] = <CT0, 5>.
A (setup/holding) priority associated with an LSP valid only if it appears
as a pair with the Class-Type. Class-Types and priorities can be randomly
paired up. You can define a maximum of eight <Class-Type, Priority> pairs.
The LSR is considered to support a particular Class-Type only if it appears
in the definition of the eight possible TE-Classes. It is suggested that all
the LSRs in the domain use the same TE-Class mapping. The index of this entry
is hwMplsTeClassId. HwMplsTeClassEntry .1.3.6.1.4.1.2011.5.25.121.1.6.1 |
hwMplsTeClassIdThis value represents the index of the TE-Class configured
on this LSR. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.6.1.1 |
hwMplsTeClassClassTypeThis value represents a Class-Type supported on the LSR.
Options:
1. ct0(1) -indicates that the class type of static CR-LSP is ct0.
2. ct1(2) -indicates that the class type of static CR-LSP is ct1.
3. ct2(3) -indicates that the class type of static CR-LSP is ct2.
4. ct3(4) -indicates that the class type of static CR-LSP is ct3.
5. ct4(5) -indicates that the class type of static CR-LSP is ct4.
6. ct5(6) -indicates that the class type of static CR-LSP is ct5.
7. ct6(7) -indicates that the class type of static CR-LSP is ct6.
8. ct7(8) -indicates that the class type of static CR-LSP is ct7.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.1.6.1.2 |
hwMplsTeClassPriorityThis value represents the preemption priority (setup or holding)
supported for a particular class-type, on the LSR.
Range: 0-7
Default: 7ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.6.1.3 |
hwMplsTeClassDescriptionTextual description of the TE-Class defined by this row.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.1.6.1.4 |
hwMplsIfBcTableThis table describes bandwidth constraints associated with MPLS TE
enabled interfaces. The index of this table is ifIndex. SEQUENCE OF HwMplsIfBcEntry .1.3.6.1.4.1.2011.5.25.121.1.7 |
hwMplsIfBcEntryThis table describes bandwidth constraints associated with MPLS TE
enabled interfaces. The index of this entry is ifIndex. HwMplsIfBcEntry .1.3.6.1.4.1.2011.5.25.121.1.7.1 |
hwMplsIfMaxResvBandwidthThe maximum reservable bandwidth on this interface.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.1 |
hwMplsIfBc0BandwidthThe bandwidth of Class-Type 0 (CT0) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.2 |
hwMplsIfBc1BandwidthThe bandwidth of Class-Type 1 (CT1) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.3 |
hwMplsIfBc2BandwidthThe bandwidth of Class-Type 2 (CT2) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.4 |
hwMplsIfBc3BandwidthThe bandwidth of Class-Type 3 (CT3) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.5 |
hwMplsIfBc4BandwidthThe bandwidth of Class-Type 4 (CT4) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.6 |
hwMplsIfBc5BandwidthThe bandwidth of Class-Type 5 (CT5) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.7 |
hwMplsIfBc6BandwidthThe bandwidth of Class-Type 6 (CT6) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.8 |
hwMplsIfBc7BandwidthThe bandwidth of Class-Type 7 (CT7) in this tunnel.
Unit: kbit/sro Unsigned32 UNITS "kilobits per second" .1.3.6.1.4.1.2011.5.25.121.1.7.1.9 |
hwStaticLspTnlTablehwStaticLspTnlTable is used to display static LSP token of
a static LSP of a specified name. The index of this table
is hwStaticLspTnlName. SEQUENCE OF HwStaticLspTnlEntry .1.3.6.1.4.1.2011.5.25.121.1.8 |
hwStaticLspTnlEntryhwStaticLspTnlTable is used to display static LSP token of
a static LSP of a specified name. The index of this entry
is hwStaticLspTnlName. HwStaticLspTnlEntry .1.3.6.1.4.1.2011.5.25.121.1.8.1 |
hwStaticLspTnlNameIndicates the name of the Static Lsp. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.1.8.1.1 |
hwStaticLspTnlTokenIndicates the token of the Static Lsp.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.8.1.2 |
hwMplsTeVpnQosTableThis table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID.
The index of this table is hwMplsTnlID. SEQUENCE OF HwMplsTeVpnQosEntry .1.3.6.1.4.1.2011.5.25.121.1.9 |
hwMplsTeVpnQosEntryThis table is used to display VPN QoS information of a specified TE Tunnel according to TunnelID.
The index of this entry is hwMplsTnlID. HwMplsTeVpnQosEntry .1.3.6.1.4.1.2011.5.25.121.1.9.1 |
hwMplsTnlIDThe value of this object identifies the TE tunnel ID. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.9.1.1 |
hwMplsTeVpnMaxBandwidthThe value of this object identifies the bandwidth the TE tunnel can provide for VPN QoS.
Unit: kbit/sro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.9.1.2 |
hwMplsTeVpnAllocatedBandwidthThe value of this object identifies the bandwidth used by VPN QoS, in Kbps.
Unit: kbit/sro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.1.9.1.3 |
hwStaticLspInIfIndexIndicates the inbound interface index of a static LSP/CR-LSP.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.1.11 |
hwStaticLspInIfNameIndicates the name of an inbound interface of a static LSP/CR-LSP.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.1.12 |
hwStaticLspDownReasonIndicates the reason for static LSP/CR-LSP Down:
0. Other
1. Static LSP/CR-LSP up
2. MPLS disabled on an interface
3. MPLS TE disabled on an interface
4. Route change
5. Tunnel binding associated with the static LSP/CR-LSP deleted
6. Static LSP/CR-LSP configuration delete
7. Inbound interface Down
8. Outbound interface Down
9. Tunnel associated with the static LSP/CR-LSP has been shut down
10. Static LSP/CR-LSP configuration update
11. The bound ring is invalid.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.1.13 |
hwMplsExtendTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.2 |
hwLspTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.2.1 |
hwMplsStaticLspUpThis notification indicates that the status of referred static LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.1 |
hwMplsStaticLspDownThis notification indicates that the status of referred static LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.2 |
hwMplsStaticCRLspUpThis notification indicates that the status of referred static CR-LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.3 |
hwMplsStaticCRLspDownThis notification indicates that the status of referred static CR-LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.4 |
hwMplsTeFrrProtAvalThis notification indicates that the primary tunnel is bound to bypass tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.5 |
hwMplsTeFrrProtNotAvalThis notification indicates that the primary tunnel is unbound to bypass tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.6 |
hwMplsTeFrrSwitchThis notification indicates that the primary tunnel is switches to the bypass tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.7 |
hwMplsTeFrrResumeThis notification indicates that the primary tunnel is switched back from the bypass tunnel. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.8 |
hwMplsTunnelHSBSwitchThis notification indicates that the data is switched from the primary CR-LSP to the HSB CR-LSP. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.9 |
hwMplsTunnelHSBResumeThis notification indicates that the data is switched from the HSB CR-LSP to the primary CR-LSP. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.10 |
hwMplsTunnelOBSwitchThis notification indicates that the primary CR-LSP is down and the Ordinary backup CR-LSP is up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.11 |
hwMplsTunnelOBResumeThis notification indicates that the data is switched from the Ordinary backup CR-LSP to the primary CR-LSP. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.12 |
hwMplsTunnelUpThe hwMplsTunnelUp trap indicates that the staus of the tunnel changes into Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.13 |
hwMplsTunnelDownThe hwMplsTunnelDown trap indicates that the staus of the tunnel changes into Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.14 |
hwMplsTunnelChangeBwThis notification indicates that the bandwidth of the tunnel is changed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.15 |
hwMplsTunnelTpOamLossSDThis object indicates that the loss ratio of the packets carried by the tunnel exceeded the first threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.16 |
hwMplsOamSDRecoveryThis object indicates that the loss ratio of the packets carried by the tunnel dropped below the first threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.17 |
hwMplsOamLossThis object indicates that TP OAM detected tunnel connectivity faults. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.18 |
hwMplsOamLossRecoveryThis object indicates that TP OAM did not detect tunnel connectivity faults. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.19 |
hwMplsOamAisThis object indicates that TP OAM detected an alarm indication signal. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.20 |
hwMplsOamAisRecoveryThis object indicates that TP OAM no longer detected alarm indication signals. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.21 |
hwMplsOamRdiThis object indicates that TP OAM detected remote defects. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.22 |
hwMplsOamRdiRecoveryThis object indicates that the remote defects detected by TP OAM were removed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.23 |
hwMplsOamMegThis object indicates that the names configured on the two ends of the tunnel are inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.24 |
hwMplsOamMegRecoveryThis object indicates that the names configured on the two ends of the tunnel now are consistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.25 |
hwMplsOamMepThis object indicates that the MEP-IDs configured on the two ends of the tunnel are inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.26 |
hwMplsOamMepRecoveryThis object indicates that the MEP-IDs configured on the two ends of the tunnel now are consistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.27 |
hwMplsOamSFThis object indicates that the loss ratio of the packets carried by the tunnel exceeded the second threshold in the local link. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.28 |
hwMplsOamSFRecoveryThis object indicates that the loss ratio of the packets carried by the tunnel dropped below the second threshold in the local link. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.29 |
hwMplsOamPeriodThis object indicates that the TP OAM detection periods on the two ends of the tunnel are inconsistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.30 |
hwMplsOamPeriodRecoveryThis object indicates that the TP OAM detection periods on the two ends of the tunnel now are consistent. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.31 |
hwMplsOamLckThis object indicates that TP OAM detected the service level of the tunnel has been locked. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.32 |
hwMplsOamLckRecoveryThis object indicates that TP OAM detected the service level of the tunnel has not been locked. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.33 |
hwMplsOamExcessThis object indicates that MPLS OAM detected the tunnel received excess alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.34 |
hwMplsOamExcessRecoveryThis object indicates that MPLS OAM detected the tunnel received excess alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.35 |
hwMplsOamMisMatchThis object indicates that MPLS OAM detected the tunnel received MisMatch alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.36 |
hwMplsOamMisMatchRecoveryThis object indicates that MPLS OAM detected the tunnel received MisMatch alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.37 |
hwMplsOamMisMergeThis object indicates that MPLS OAM detected the tunnel received MisMerge alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.38 |
hwMplsOamMisMergeRecoveryThis object indicates that MPLS OAM detected the tunnel received MisMerge alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.39 |
hwMplsOamUnknownThis object indicates that MPLS OAM detected the tunnel received Unknown alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.40 |
hwMplsOamUnknownRecoveryThis object indicates that MPLS OAM detected the tunnel received Unknown alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.41 |
hwMplsOamBDIThis object indicates that MPLS OAM detected the tunnel received BDI alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.42 |
hwMplsOamBDIRecoveryThis object indicates that MPLS OAM detected the tunnel received BDI alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.43 |
hwMplsOamFailThis object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.44 |
hwMplsOamFailRecoveryThis object indicates that MPLS OAM detected the tunnel received OAMFAIL alarm end. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.45 |
hwMplsTunnelPrimaryUpThis notification indicates that the status of the RSVP-TE Primary LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.46 |
hwMplsTunnelPrimaryDownThis notification indicates that the status of the RSVP-TE Primary LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.47 |
hwMplsTunnelHotstandbyUpThis notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.48 |
hwMplsTunnelHotstandbyDownThis notification indicates that the status of the RSVP-TE Hot-standby LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.49 |
hwMplsTunnelOrdinaryUpThis notification indicates that the status of the RSVP-TE Ordinary LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.50 |
hwMplsTunnelOrdinaryDownThis notification indicates that the status of the RSVP-TE Ordinary LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.51 |
hwMplsTunnelBesteffortUpThis notification indicates that the status of the RSVP-TE Best-effort LSP changes to Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.52 |
hwMplsTunnelBesteffortDownThis notification indicates that the status of the RSVP-TE Best-effort LSP changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.53 |
hwMplsTeAutoTunnelDownClearThis notification indicates that the TE Auto tunnel Down alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.54 |
hwMplsTeAutoTunnelPrimaryDownClearThis notification indicates that the Down alarm about the primary LSP in the TE Auto tunnel was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.55 |
hwMplsTunnelBBSwitchThis notification indicates that the primary CR-LSP is Down and the Best-effort backup CR-LSP is Up. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.56 |
hwMplsTunnelBBResumeThis notification indicates that data is switched from the Best-effort backup CR-LSP to the primary CR-LSP. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.57 |
hwMplsExtTunnelDownThis notification indicates that the status of te tunnel changes to Down. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.58 |
hwMplsExtTunnelDownClearThis notification indicates that the down alarm of te tunnel was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.59 |
hwMplsOamLocalLockThis object indicates that TP OAM detected the tunnel has been locked. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.60 |
hwMplsOamLocalLockRecoveryThis object indicates that TP OAM detected the tunnel has not been locked. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.61 |
hwMplsTunnelDeleteThis notification indicates that the mpls te tunnel was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.62 |
hwMplsLspThresholdExceedThis object indicates that lsp count has exceeded the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.63 |
hwMplsLspThresholdExceedClearThis object indicates that lsp count has resumed from exceeding the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.64 |
hwMplsLspTotalCountExceedThis object indicates that lsp count has reached the total count. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.65 |
hwMplsLspTotalCountExceedClearThis object indicates that lsp count has resumed from reaching the total count. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.66 |
hwMplsDynamicLabelThresholdExceedThis object indicates that label usage has exceeded the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.67 |
hwMplsDynamicLabelThresholdExceedClearThis object indicates that label usage has resumed from exceeding the threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.68 |
hwMplsDynamicLabelTotalCountExceedThis object indicates that label count has reached the total count. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.69 |
hwMplsDynamicLabelTotalCountExceedClearThis object indicates that label usage count has resumed from reaching the total count. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.70 |
hwMplsResourceThresholdExceedThis object indicates that the number of MPLS resources has exceeded the upper threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.71 |
hwMplsResourceThresholdExceedClearThis object indicates that the number of MPLS resources has fallen below the lower threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.72 |
hwMplsResourceTotalCountExceedThis object indicates that the number of MPLS resources has reached the maximum number. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.73 |
hwMplsResourceTotalCountExceedClearThis object indicates that the number of MPLS resources fallen below the recovery number. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.74 |
hwMplsLspLoopBackThis object indicates that the lsp was looped back. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.75 |
hwMplsLspLoopBackClearThis object indicates that loopback of the LSP is restored. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.76 |
hwMplsTunnelCommitLostThis object indicates that, after the device saves MPLS TE tunnel configurations, the device commits only some MPLS tunnel configurations. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.77 |
hwMplsTunnelCommitLostClearThis object indicates that, after the device saves MPLS TE tunnel configurations, the device commits all MPLS tunnel configurations. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.1.78 |
hwMplsTrapObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.2.2 |
hwMplsTunnelIfNameThe Tunnel Interface name.roobsolete SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.2.2.1 |
hwMplsTunnelFrrConfigOperThe value of this object identifies the operation that an FRR configuration is committed on the tunnel.
Options:
1.unconfig(0) -indicates the configuration of the undo mpls te fast-reroute command is committed.
2.config(1) -indicates the configuration of the mpls te fast-reroute command is committed.
3.unknow(2) -indicates an unknown operation.roobsolete Enumeration .1.3.6.1.4.1.2011.5.25.121.2.2.2 |
hwMplsTunnelDownReasonIndicates the alarm reason as below:
1. Other;
2. Static LSP down;
3. Static CR-LSP down;
4. The out interface of the RSVP LSP ingress is down;
5. The resource of RSVP LSP is preempted;
6. RSVP message timeout;
7. RSVP neighbor lost;
8. The bypass-tunnel is down or is unbinded with main tunnel, as bypass-tunnel is in used;
9. CSPF compute fail;
10.User shutdown the tunnel;
11.TPOAM indicates the connectivity fault of the link;
12.TPOAM indicates receive alarm indication signal defect of the link;
13.TPOAM indicates the remote defect of the link;
14.TPOAM indicates receive unexpected MEG-ID defect of the link;
15.TPOAM indicates receive unexpected MEP-ID defect of the link;
16.TPOAM indicates packet lost exceed signal fault threshold in the local link;
17.TPOAM indicates packet unexpected period defect of the link;
18.MPLS OAM connectivity fault;
19.MPLS OAM TTSI excess;
20.MPLS OAM TTSI mismatch;
21.MPLS OAM TTSI merge error;
22.MPLS OAM unknown error;
23.MPLS OAM BDI;
24.MPLS OAM FDI;
25.MPLS OAM signal fail;
26.MPLS OAM signal degrade;
27.MPLS OAM fail;
28.Service resume;
29.Service delete;
100. Clear.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.2.2.3 |
hwMplsLspProtocolThe value of this object identifies the protocol of the lsp which exceeds the threshold or total count.
Options:
1.ldp(1) -indicates the lsp is ldp lsp.
2.bgp(2) -indicates the lsp is bgp lsp.
3.bgpv6(3) -indicates the lsp is bgpv6 lsp.
4.ldpfrr(4) -indicates the lsp is ldp frr lsp.
5.rsvp(5) -indicates the lsp is rsvp te lsp.
6.totalLsp(6) -indicates the lsp is total lsp.
7.totalCrLsp(7) -indicates the lsp is total cr-lsp.
8.ldpIngress(8) -indicates the lsp is ldp ingress lsp.
9.ldpTransit(9) -indicates the lsp is ldp transit lsp.
10.ldpEgress(10) -indicates the lsp is ldp egress lsp.
11.bgpIngress(11) -indicates the lsp is bgp ingress lsp.
12.bgpEgress(12) -indicates the lsp is bgp egress lsp.
13.bgpv6Ingress(13) -indicates the lsp is bgpv6 ingress lsp.
14.bgpv6Egress(14) -indicates the lsp is bgpv6 egress lsp.
15.rsvpIngress(15) -indicates the lsp is rsvp te ingress lsp.
16.rsvpTransit(16) -indicates the lsp is rsvp te transit lsp.
17.rsvpEgress(17) -indicates the lsp is rsvp te egress lsp.
18.totalLspIngress(18) -indicates the lsp is total ingress lsp.
19.totalLspTransit(19) -indicates the lsp is total transit lsp.
20.totalLspEgress(20) -indicates the lsp is total egress lsp.
21.totalCrLspIngress(21) -indicates the lsp is total ingress cr-lsp.
22.totalCrLspTransit(22) -indicates the lsp is total transit cr-lsp.
23.totalCrLspEgress(23) -indicates the lsp is total egress cr-lsp.
24.totalPublicNetLspIngressTransit(24) -indicates the lsp is total ingress and transit public netwrok lsp.
25.totalPublicNetLspTransitEgress(25) -indicates the lsp is total transit and egress public network cr-lsp.
26.privateNetBgp(26) -indicates the lsp is private network bgp lsp.
27.unknown(100) -indicates the lsp type is unknown.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.2.2.4 |
hwMplsLspThresholdThe value of this object identifies the threshold of the lsp.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.5 |
hwMplsLspTotalCountThe value of this object identifies the total permit count of lsp.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.6 |
hwMplsLspCurrentCountThe value of this object identifies the current count of the lsp.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.7 |
hwMplsTunnelDownLSRIDThe value of this object identifies the LSR ID of the error node on a tunnel.ro MplsLsrIdentifier (MPLS-TC-STD-MIB) .1.3.6.1.4.1.2011.5.25.121.2.2.8 |
hwMplsTunnelDownIfIpAddrThe value of this object identifies the IP address of the error interface on a tunnel.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.2011.5.25.121.2.2.9 |
hwMplsTunnelDownIfIpAddrTypeThe value of this object identifies the IP address type of the error interface on a tunnel.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.2011.5.25.121.2.2.10 |
hwMplsResourceTypeThe value of this object identifies that the number of MPLS resources has exceeded the threshold or the maximum number.
Options:
1.autoBypassTunnelIf(1) -Indicates that the resource is auto bypass tunnel interface.
2.p2mpAutoTunnelIf(2) -Indicates that the resource is P2MP auto tunnel interface.
3.teBfd(3) -Indicates that the resource is dynamic BFD for TE LSP.
4.ldpBfd(4) -Indicates that the resource is dynamic BFD for LDP LSP.
5.mldpTotalTree(5) -Indicates that the resource is the total number of MLDP trees.
6.mldpTotalBranch(6) -Indicates that the resource is the total number of MLDP branches.
7.ldpTotalRemoteAdjacency(7) -Indicates that the resource is LDP total remote adjacency.
8.outSegment(8) -Indicates that the resource is LDP outSegment.
9.autoPrimaryTunnelIf(9) -Indicates that the resource is auto primary tunnel interface.
10.ldpTotalLocalAdjacency(10) -Indicates that the resource is LDP total local adjacency.
11.unknown(100) -Indicates that the resource type is unknown.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.2.2.11 |
hwMplsResourceCurrentCountThe value of this object identifies the number of the resources.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.12 |
hwMplsResourceThresholdThe value of this object identifies the threshold for the number of the resources.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.13 |
hwMplsResourceTotalCountThe value of this object identifies the maximum number of allowed resources.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.14 |
hwMplsSessionTunnelIdThe value of this object identifies the Tunnel ID.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.15 |
hwMplsLocalLspIdThe value of this object identifies the LSP ID.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.16 |
hwMplsIngressLsrIdThe value of this object identifies the ingress LSR ID.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.17 |
hwMplsEgressLsrIdThe value of this object identifies the egress LSR ID.ro Integer32 .1.3.6.1.4.1.2011.5.25.121.2.2.18 |
hwMplsLspNameThis object indicates the name of an bidirectional static CR-LSP.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.2.2.19 |
hwMplsTunnelFrrConfigChangeWhen the trap indicating that TE-Frr configuration of Tunnel is changed is sent, the cause for the change of TE-FRR configuration of Tunnel is displayed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.2.3 |
hwMplsGlobalObject OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.3 |
hwMplsGlobalWorkModeThe work mode of DS-TE system, default mode is nonstandard.
Options:
1. standard(1) -indicates work mode of DS-TE system is standard
2. nonstandard(2) -indicates work mode of DS-TE system is nonstandardro Enumeration .1.3.6.1.4.1.2011.5.25.121.3.1 |
hwMplsGlobalBcModelBandwidth Constraint Model currently used by this LSR.
Options:
1. rdm(1) -indicates that the bandwidth constraint model is RDM.
2. mam(2) -indicates that the bandwidth constraint model is MAM.
3. extendMam(3) -indicates that the bandwidth constraint model is ExtendMam.ro Enumeration .1.3.6.1.4.1.2011.5.25.121.3.2 |
hwMplsDynamicLabelTotalCountThe value of this object identifies the total permit count of dynamic label.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.3.3 |
hwMplsDynamicLabelCurrentCountThe value of this object identifies the current count of the dynamic label.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.3.4 |
hwMplsDynamicLabelThresholdUpperLimitThe upper limit threshold value (%) of dynamic label, default value is 80.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.3.5 |
hwMplsDynamicLabelThresholdLowerLimitThe lower limit threshold value (%) of dynamic label, default value is 70.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.3.6 |
hwMplsLspStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.4 |
hwMplsLspStatisticsTablehwMplsLspStatisticsTable is used to display the number of ingress LSPs,
transit LSPs, or egress LSPs of specified types. The index of this table
is hwMplsLspStatisticsLspType. SEQUENCE OF HwMplsLspStatisticsEntry .1.3.6.1.4.1.2011.5.25.121.4.1 |
hwMplsLspStatisticsEntryhwMplsLspStatisticsTable is used to display the number of ingress LSPs,
transit LSPs, or egress LSPs of specified types. The index of this entry
is hwMplsLspStatisticsLspType. HwMplsLspStatisticsEntry .1.3.6.1.4.1.2011.5.25.121.4.1.1 |
hwMplsLspStatisticsLspTypeThis object indicates the LSP type.
Options:
1. staticLsp(1) -indicates the static LSP.
2. staticCrLsp(2) -indicates the static CR-LSP.
3. ldpLsp(3) -indicates the LDP LSP.
4. rsvpCrLsp(4) -indicates the RSVP LSP.
5. bgpLsp(5) -indicates the BGP LSP.
6. asbrLsp(6) -indicates the ASBR LSP.
7. bgpIpv6Lsp(7) -indicates the BGP IPv6 LSP.
8. l3vpnIpv6Lsp(8)-indicates the L3VPN IPv6 LSP. Enumeration .1.3.6.1.4.1.2011.5.25.121.4.1.1.1 |
hwMplsLspStatisticsIngressLspCountThis object indicates the number of ingress LSPs of a specified type.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.4.1.1.2 |
hwMplsLspStatisticsTransitLspCountThis object indicates the number of transit LSPs of a specified type.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.4.1.1.3 |
hwMplsLspStatisticsEgressLspCountThis object indicates the number of egress LSPs of a specified type.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.4.1.1.4 |
hwMplsLspStatisticsTotalLspCountThis object indicates the total number of the ingress LSPs, transit LSPs and egress LSP of specified types.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.4.1.1.5 |
hwMplsTrafficStatisticsStaticLspTableIndicates the traffic statistics of a LSP.
The indexes of this table is hwMplsTrafficStatisticsStaticLspName. SEQUENCE OF HwMplsTrafficStatisticsStaticLspEntry .1.3.6.1.4.1.2011.5.25.121.4.2 |
hwMplsTrafficStatisticsStaticLspEntryIndicates the traffic statistics of a LSP. The indexes of this entry is
hwMplsTrafficStatisticsStaticLspName. HwMplsTrafficStatisticsStaticLspEntry .1.3.6.1.4.1.2011.5.25.121.4.2.1 |
hwMplsTrafficStatisticsStaticLspNameIndicates the name of the static LSP or CR-LSP.
The name is appointed when the static LSP or CR-LSP
is created. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2011.5.25.121.4.2.1.1 |
hwMplsTrafficStatisticsStaticLspForwardInBytesAn estimate of the forward of bistatic LSP's current incoming traffic statistics
in units of bytes.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: bytesro Counter64 UNITS "bytes" .1.3.6.1.4.1.2011.5.25.121.4.2.1.2 |
hwMplsTrafficStatisticsStaticLspForwardInPacketsAn estimate of the forward of bistatic LSP's current incoming traffic statistics
in units of packets.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: packetsro Counter64 UNITS "packets" .1.3.6.1.4.1.2011.5.25.121.4.2.1.3 |
hwMplsTrafficStatisticsStaticLspForwardOutBytesAn estimate of the forward of bistatic LSP's current outgoing traffic statistics
in units of bytes.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: bytesro Counter64 UNITS "bytes" .1.3.6.1.4.1.2011.5.25.121.4.2.1.4 |
hwMplsTrafficStatisticsStaticLspForwardOutPacketsAn estimate of the forward of bistatic LSP's current outgoing traffic statistics
in units of packets.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: packetsro Counter64 UNITS "packets" .1.3.6.1.4.1.2011.5.25.121.4.2.1.5 |
hwMplsTrafficStatisticsStaticLspBackwardInBytesAn estimate of the backward of bistatic LSP's current incoming traffic statistics
in units of bytes.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: bytesro Counter64 UNITS "bytes" .1.3.6.1.4.1.2011.5.25.121.4.2.1.6 |
hwMplsTrafficStatisticsStaticLspBackwardInPacketsAn estimate of the backward of bistatic LSP's current incoming traffic statistics
in units of packets.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: packetsro Counter64 UNITS "packets" .1.3.6.1.4.1.2011.5.25.121.4.2.1.7 |
hwMplsTrafficStatisticsStaticLspBackwardOutBytesAn estimate of the backward of bistatic LSP's current outgoing traffic statistics
in units of bytes.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: bytesro Counter64 UNITS "bytes" .1.3.6.1.4.1.2011.5.25.121.4.2.1.8 |
hwMplsTrafficStatisticsStaticLspBackwardOutPacketsAn estimate of the backward of bistatic LSP's current outgoing traffic statistics
in units of packets.
For a sub-layer which has no concept of
traffic statistics, this object should be zero.
Unit: packetsro Counter64 UNITS "packets" .1.3.6.1.4.1.2011.5.25.121.4.2.1.9 |
hwMplsExtendConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.6 |
hwMplsExtendGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.6.1 |
hwMplsExtendCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.6.2 |
hwMplsRingMib OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.7 |
hwMplsRingTableIndicates the table information of the MPLS ring. SEQUENCE OF HwMplsRingEntry .1.3.6.1.4.1.2011.5.25.121.7.1 |
hwMplsRingEntryIndicates the table information of the MPLS ring. HwMplsRingEntry .1.3.6.1.4.1.2011.5.25.121.7.1.1 |
hwMplsRingIDIndicates the ID of the MPLS ring. Unsigned32 .1.3.6.1.4.1.2011.5.25.121.7.1.1.1 |
hwMplsRingNodeIDIndicates the ID of the current Node on the MPLS ring.ro Unsigned32 .1.3.6.1.4.1.2011.5.25.121.7.1.1.2 |
hwMplsRingNameIndicates the name of MPLS ring.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.7.1.1.3 |
hwMplsRingDirectionIndicates the direction of the MPLS ring.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.7.1.1.4 |
hwMplsRingSwitchReasonIndicates the switch reason of the MPLS ring.ro OCTET STRING .1.3.6.1.4.1.2011.5.25.121.7.1.1.5 |
hwMplsRingTrap OBJECT IDENTIFIER .1.3.6.1.4.1.2011.5.25.121.7.2 |
hwMplsRingSwitchThe notification indicates that the MPLS ring switched. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.1 |
hwMplsRingResumeThe notification indicates that the MPLS ring resumed. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.2 |
hwMplsRingWestOamLossThe notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.3 |
hwMplsRingWestOamLossClearThe notification indicates that the hwMplsRingWestOamLoss alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.4 |
hwMplsRingEastOamLossThe notification indicates that no expected CV/FFD packet is received for three consecutive cycles in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.5 |
hwMplsRingEastOamLossClearThe notification indicates that the hwMplsRingEastOamLoss alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.6 |
hwMplsRingWestOamRDIThe notification indicates that RDI packets are received in the west of the MPLS ring, indicating that a fault occurs on the forward ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.7 |
hwMplsRingWestOamRDIClearThe notification indicates that the hwMplsRingWestOamRDI alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.8 |
hwMplsRingEastOamRDIThe notification indicates that RDI packets are received in the east of the MPLS ring, indicating that a fault occurs on the forward ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.9 |
hwMplsRingEastOamRDIClearThe notification indicates that the hwMplsRingEastOamRDI alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.10 |
hwMplsRingWestOamUnexpectedMEGThe notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.11 |
hwMplsRingWestOamUnexpectedMEGClearThe notification indicates that the hwMplsRingWestOamUnexpectedMEG alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.12 |
hwMplsRingEastOamUnexpectedMEGThe notification indicates that a CCM frame carrying a correct MEG level but incorrect MEG ID is received in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.13 |
hwMplsRingEastOamUnexpectedMEGClearThe notification indicates that the hwMplsRingEastOamUnexpectedMEG alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.14 |
hwMplsRingWestOamUnexpectedPeriodThe notification indicates that a CCM frame carrying a correct MEG level, MEG ID,
and MEP ID but incorrect period value is received in the west MEP of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.15 |
hwMplsRingWestOamUnexpectedPeriodClearThe notification indicates that the hwMplsRingWestOamUnexpectedPeriod alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.16 |
hwMplsRingEastOamUnexpectedPeriodThe notification indicates that a CCM frame carrying a correct MEG level, MEG ID,
and MEP ID but incorrect period value is received in the east MEP of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.17 |
hwMplsRingEastOamUnexpectedPeriodClearThe notification indicates that the hwMplsRingEastOamUnexpectedPeriod alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.18 |
hwMplsRingWestOamExcessThe notification indicates that five or more CV/FFD packets are correctly received
within three consecutive cycles in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.19 |
hwMplsRingWestOamExcessClearThe notification indicates that the hwMplsRingWestOamExcess alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.20 |
hwMplsRingEastOamExcessThe notification indicates that five or more CV/FFD packets are correctly received
within three consecutive cycles in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.21 |
hwMplsRingEastOamExcessClearThe notification indicates that the hwMplsRingEastOamExcess alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.22 |
hwMplsRingWestOamSDThe notification indicates that the number of packets for connectivity check received
in the west of the MPLS ring is smaller than the SD threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.23 |
hwMplsRingWestOamSDClearThe notification indicates that the hwMplsRingWestOamSD alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.24 |
hwMplsRingEastOamSDThe notification indicates that the number of packets for connectivity check received
in the east of the MPLS ring is smaller than the SD threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.25 |
hwMplsRingEastOamSDClearThe notification indicates that the hwMplsRingEastOamSD alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.26 |
hwMplsRingWestOamSFThe notification indicates that the number of packets for connectivity check received in
the west of the MPLS ring is smaller than the SF threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.27 |
hwMplsRingWestOamSFClearThe notification indicates that the hwMplsRingWestOamSF alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.28 |
hwMplsRingEastOamSFThe notification indicates that the number of packets for connectivity check received in
the east of the MPLS ring is smaller than the SF threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.29 |
hwMplsRingEastOamSFClearThe notification indicates that the hwMplsRingEastOamSF alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.30 |
hwMplsRingWestAPSSwitchThe notification indicates that APS switching occurs in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.31 |
hwMplsRingWestAPSResumeThe notification indicates that APS switches back in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.32 |
hwMplsRingEastAPSSwitchThe notification indicates that APS switching occurs in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.33 |
hwMplsRingEastAPSResumeThe notification indicates that APS switches back in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.34 |
hwMplsRingWestAPSSwitchFailThe notification indicates that the remote APS switching fails in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.35 |
hwMplsRingWestAPSSwitchFailClearThe notification indicates that the hwMplsRingWestAPSSwitchFail alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.36 |
hwMplsRingEastAPSSwitchFailThe notification indicates that the remote APS switching fails in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.37 |
hwMplsRingEastAPSSwitchFailClearThe notification indicates that the hwMplsRingEastAPSSwitchFail alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.38 |
hwMplsRingWestAPSLostThe notification indicates that APS packets are missing in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.39 |
hwMplsRingWestAPSLostClearThe notification indicates that the hwMplsRingWestAPSLost alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.40 |
hwMplsRingEastAPSLostThe notification indicates that APS packets are missing in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.41 |
hwMplsRingEastAPSLostClearThe notification indicates that the hwMplsRingEastAPSLost alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.42 |
hwMplsRingWestAPSMismatchThe notification indicates that the source ID carried by APS packets received in the west
is different from the peer source ID configured for the west state machine on the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.43 |
hwMplsRingWestAPSMismatchClearThe notification indicates that the hwMplsRingWestAPSMismatch alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.44 |
hwMplsRingEastAPSMismatchThe notification indicates that the source ID carried by APS packets received in the east
is different from the peer source ID configured for the east state machine on the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.45 |
hwMplsRingEastAPSMismatchClearThe notification indicates that the hwMplsRingEastAPSMismatch alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.46 |
hwMplsRingWestOamUnexpectedMEPThe notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the west of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.47 |
hwMplsRingWestOamUnexpectedMEPClearThe notification indicates that the hwMplsRingWestOamUnexpectedMEP alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.48 |
hwMplsRingEastOamUnexpectedMEPThe notification indicates that a CCM frame carrying a correct MEG level and correct MEG ID but not the expected MEP ID is received in the east of the MPLS ring. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.49 |
hwMplsRingEastOamUnexpectedMEPClearThe notification indicates that the hwMplsRingEastOamUnexpectedMEP alarm was cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.5.25.121.7.2.50 |