HUAWEI-GBOND-MIB
AI MIB Summary
The HUAWEI-GBOND-MIB module enables SNMP-based monitoring and configuration of Huawei bond aggregation interfaces compliant with ITU-T G.998.1, G.998.2, and G.998.3 standards. It provides granular visibility into bonded link states, interface statistics, and aggregation session parameters for multi-link Ethernet bonding deployments.
This MIB is used for defining Huawei's GBOND management MIB objects, which is defined base on ITU-T G.998.1, G.998.2 and G.998.3.
Main OID:
hwGBond.1.3.6.1.4.1.2011.6.137
102
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
102 total| Object Name |
|---|
hwGBondThis MIB is used for defining Huawei's GBOND management MIB objects,
which is defined base on ITU-T G.998.1, G.998.2 and G.998.3. MODULE-IDENTITY .1.3.6.1.4.1.2011.6.137 |
hwGBondConfTableGroup bonding configuration table.
This table is used to describe the configuration, parameters, and running status of the bonding group.
The index of this table is hwGBondPriPort. SEQUENCE OF HwGBondConfEntry .1.3.6.1.4.1.2011.6.137.1 |
hwGBondConfEntryGroup bonding configuration table.
This table is used to describe the configuration, parameters, and running status of the bonding group.
The index of this entry is hwGBondPriPort. HwGBondConfEntry .1.3.6.1.4.1.2011.6.137.1.1 |
hwGBondPriPortIndex of the bonding group, which should be equal to the ifindex of the primary port. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2011.6.137.1.1.1 |
hwGBondAdminSchemeA desired bonding scheme for a bonding group.
The port to use corresponding bonding scheme if supported.
Options:
1. g9981(1) - Instructs the port to use G.998.1 bonding
2. g9982(2) - Instructs the port to use G.998.2 bonding
3. g9983(3) - Instructs the port to use G.998.3 bonding
The hwGBondAdminScheme changes must be performed when the admin status of the
bonding group is deactivated.rw GBondScheme .1.3.6.1.4.1.2011.6.137.1.1.2 |
hwGBondPeerAdminSchemeA desired bonding peer scheme for a bonding group.
The port to use corresponding bonding scheme if supported.
Options:
1. g9981(1) - Instructs the port to use G.998.1 bonding
2. g9982(2) - Instructs the port to use G.998.2 bonding
3. g9983(3) - Instructs the port to use G.998.3 bonding
The hwGBondPeerAdminScheme changes must be performed when the admin status of the
bonding group is deactivated.rw GBondScheme .1.3.6.1.4.1.2011.6.137.1.1.3 |
hwGBondDiscoveryCodeA discovery Code of the G.Bond port (GBS).
A unique 6 octet long code used by the discovery function.
This object must be instantiated for the -O subtype GBS before
writing operations on the gBondBceRemoteDiscoveryCode
(Set_if_Clear and Clear_if_Same) are performed by BCEs
associated with the GBS.
The initial value of this object for -R subtype ports after
reset is all zero. For -R subtype ports, the value of this
object cannot be changed directly. This value may be changed
as a result of writing operation on the
gBondBceRemoteDiscoveryCode object of remote BCE of -O
subtype, connected to one of the local BCEs associated with
the GBS.
Discovery must be performed when the link is down.
Attempts to change this object must be rejected (in case of
SNMP with the error inconsistent value), if the link is Up or
Initializing.
This object maps to the TR-159 attribute aGroupDiscoveryCode.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.1.1.4 |
hwGBondTargetUpDataRateA desired bonding group data rate in the upstream direction, in Kbps,
to be achieved during initialization, under restrictions placed upon
the member ports by their respective configuration settings.
This object is deprecated in favour of hwGBondGroupProfTargetDataRateUs.rwdeprecated Unsigned32(1..1000000|9999999) .1.3.6.1.4.1.2011.6.137.1.1.5 |
hwGBondTargetDownDataRateA desired bonding group data rate in the downstream direction, in Kbps,
to be achieved during initialization, under restrictions placed upon
the member ports by their respective configuration settings.
This object is deprecated in favour of hwGBondGroupProfTargetDataRateDs.rwdeprecated Unsigned32(1..1000000|9999999) .1.3.6.1.4.1.2011.6.137.1.1.6 |
hwGBondThreshLowUpRateThis object configures the bonding group low upstream rate crossing alarm threshold.
This object is deprecated in favour of hwGBondGroupProfThreshLowDataRateUs.rwdeprecated Unsigned32 .1.3.6.1.4.1.2011.6.137.1.1.7 |
hwGBondThreshLowDownRateThis object configures the bonding group low downstream rate crossing alarm threshold.
This object is deprecated in favour of hwGBondGroupProfThreshLowDataRateDs.rwdeprecated Unsigned32 .1.3.6.1.4.1.2011.6.137.1.1.8 |
hwGBondLowRateCrossingEnableIndicates whether gBondLowUpRateCrossing and
gBondLowDownRateCrossing notifications should be generated
for this interface.
Options:
1. disable(1) - Indicates that the notifications are disabled
2. enable(2) - Indicates that the notifications are enabled
This object is read-write for the -O subtype G.Bond ports
and irrelevant for the -R subtypes.
This object must be maintained in a persistent manner.
This object maps to the TR-159 attribute aGroupLowRateCrossingEnable.
This object is deprecated in favour of hwGBondGroupProfLowRateCrossingEnable.rwdeprecated Enumeration .1.3.6.1.4.1.2011.6.137.1.1.9 |
hwGBondDescThe description of the bonding group.rw OCTET STRING .1.3.6.1.4.1.2011.6.137.1.1.10 |
hwGBondAdminStatusThe admin status of the bonding group, when the admin-status is down, no service
should be allowed.
Options:
1. deactivate(1) - Deactivate status
2. activate(2) - Activate statusrw Enumeration .1.3.6.1.4.1.2011.6.137.1.1.11 |
hwGBondRowStatusThis object is used to create a new row or delete an existing row in
this table.
The bonding group can not be deleted when service configured on this group.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.1.1.12 |
hwGBondPrimaryStatusThe primary status of the bonding group. This parameter indicates the current overall
service condition of an entity, i.e., whether it is in-service or out-of-service.
Options:
1. is-nr(1) - In service, normal
2. is-anr(2) - In service, abnormal
3. is-rst(3) - In service, restricted
4. is-anrst(4) - In service, abnormal & restricted
5. oos-au(5) - Out of service, autonomous
6. oos-ma(6) - Out of service, management
7. oos-auma(7) - Out of service, autonomous & management
8. oos-aurst(8) - Out of service, autonomous & restricted
9. oos-maanr(9) - Out of service, management & abnormalro Enumeration .1.3.6.1.4.1.2011.6.137.1.1.13 |
hwGBondSecondaryStatusThis parameter indicates the secondary status of the bonding group. The parameter provides additional
information pertaining to PST and PSTQ. For example, it may indicate the type and reason of
the external command, the event that occurred in the Network Element, etc. Multiple values may
apply to an entity at a given moment. The highest bit of SST value indicates the sst-ains(0) status;
the second highest bit of SST value indicates the sst-faf(1) status, and the rest can be deduced by analogy.
This BITS structure can report the following status:
1. sst-ains(0) - This bit position positively reports that the status of the board is automatic in-service
2. sst-faf(1) - Facility failure
3. sst-flt(2) - Fault
4. sst-lpbk(3) - Loopback
5. sst-mea(4) - Mismatch of equipment and attributes
6. sst-sgeo(5) - Supporting entity outage
7. sst-stbyh(6) - Standby-hot
8. sst-ts(7) - Test
9. sst-uas(8) - Unassigned
10. sst-ueq(9) - Unequipped
11. sst-wrk(10) - Working
12. sst-pwr(11) - Powerro Bits .1.3.6.1.4.1.2011.6.137.1.1.14 |
hwGBondGroupCfgProfThis object configures the bonding group profile name.rw OCTET STRING .1.3.6.1.4.1.2011.6.137.1.1.15 |
hwGBondPortStatusTableThis table provides overall status information of G.Bond ports, complementing the
generic status information from the ifTable of IF-MIB. Additional status information
about connected BCEs is available from the relevant line MIBs.
This table contains live data from the equipment. As such, it is not persistent.
The index of this table is hwGBondPriPort. SEQUENCE OF HwGBondPortStatusEntry .1.3.6.1.4.1.2011.6.137.2 |
hwGBondPortStatusEntryThis table provides overall status information of G.Bond ports, complementing the
generic status information from the ifTable of IF-MIB. Additional status information
about connected BCEs is available from the relevant line MIBs.
This table contains live data from the equipment. As such, it is not persistent.
The index of this entry is hwGBondPriPort. HwGBondPortStatusEntry .1.3.6.1.4.1.2011.6.137.2.1 |
hwGBondUpDataRateA current G.Bond port operational data rate in the upstream direction, in bps.
This object represents an estimation of the sum of individual
BCE upstream data rates, modified to compensate for fragmentation and
encapsulation overhead(e.g., for an ethernet service, the target data
rate of 10Mbps shall allow lossless transmission of full-duplex 10Mbps
ethernet frame stream with minimal inter-frame gap).ro Integer32 UNITS "bps" .1.3.6.1.4.1.2011.6.137.2.1.1 |
hwGBondDownDataRateA current G.Bond port operational data rate in the downstream direction, in bps.
This object represents an estimation of the sum of individual
BCE downstream data rates, modified to compensate for fragmentation and
encapsulation overhead (e.g., for an ethernet service, the target data
rate of 10Mbps shall allow lossless transmission of full-duplex 10Mbps
ethernet frame stream with minimal inter-frame gap).ro Integer32 UNITS "bps" .1.3.6.1.4.1.2011.6.137.2.1.2 |
hwGBondNumBCEsThe Number of BCEs that is currently aggregated by the local GBS
(assigned to the G.Bond port using ifStackTable).
This number is never greater than gBondCapacity.
This object shall be automatically incremented or decremented
when a BCE is added or deleted to/from the G.Bond port using
ifStackTable.
This object maps to the TR-159 attribute aGroupNumChannels.ro Unsigned32 .1.3.6.1.4.1.2011.6.137.2.1.3 |
hwGBondEthInErrorsThe number of error fragments, that have been received across
the gamma interface.
This object is deprecated in favour of hwGBondEthPortPerfRxErrors.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.4 |
hwGBondEthInSmallFragmentsThe number of fragments smaller than minFragmentSize(64 Bytes), that have been received across
the gamma interface and discarded.
This object is deprecated in favour of hwGBondEthPortPerfRxSmallFragments.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.5 |
hwGBondEthInLargeFragmentsThe number of fragments larger than minFragmentSize(512 Bytes), that have been received across
the gamma interface and discarded.
This object is deprecated in favour of hwGBondEthPortPerfRxLargeFragments.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.6 |
hwGBondEthInBadFragmentsThe number of fragments which do not fit into the sequence expected by the frame assembly
function, that have been received across the gamma interface and discarded (the frame buffer
is flushed to the next valid frame start).
This object is deprecated in favour of hwGBondEthPortPerfRxBadFragments.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.7 |
hwGBondEthInLostFragmentsThe number of gaps in the sequence of fragments, which have been received across the gamma
interface (the frame buffer is flushed to the next valid frame start, when fragment/fragments
expected by the frame assembly function is/are not received).
This object is deprecated in favour of hwGBondEthPortPerfRxLostFragments.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.8 |
hwGBondEthInLostStartsThe number of missing StartOfPacket indicators expected by the frame assembly function.
This object is deprecated in favour of hwGBondEthPortPerfRxLostStarts.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.9 |
hwGBondEthInLostEndsThe number of missing EndOfPacket indicators expected by the frame assembly function.
This object is deprecated in favour of hwGBondEthPortPerfRxLostEnds.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.10 |
hwGBondEthInOverflowsThe number of fragments, received across the gamma interface and discarded, which would
have caused the frame assembly buffer to overflow.
This object is deprecated in favour of hwGBondEthPortPerfRxOverflows.rodeprecated Gauge32 .1.3.6.1.4.1.2011.6.137.2.1.11 |
hwGBondOperSchemeCurrent operating bonding scheme of a G.Bond port.
Options:
1. g9981(1) - Instructs the port to use G.998.1 bonding
2. g9982(2) - Instructs the port to use G.998.2 bonding
3. g9983(3) - Instructs the port to use G.998.3 bondingro GBondScheme .1.3.6.1.4.1.2011.6.137.2.1.12 |
hwGBondOperLastUpTimeBonding group last up time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.2.1.13 |
hwGBondOperLastDownTimeBonding group last down time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.2.1.14 |
hwGBondOperReInitsBonding group re-initial counters.ro Unsigned32 .1.3.6.1.4.1.2011.6.137.2.1.15 |
hwGBondOperStatusThe current operational state of the xdsl bonding-group.
Options:
1. activated(1) - The value of activated(1) indicates that the
operational packets can be passed.
2. activating(2) - The value of activating(2) should be a transient condition before
changing to activated, and the operational packets cannot be passed.
3. deactivated(3) - The value of deactivated(3) indicates that the
operational packets cannot be passed.ro Enumeration .1.3.6.1.4.1.2011.6.137.2.1.16 |
hwGBondTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.3 |
hwGBondCommonTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.3.1 |
hwGBondCommonTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.3.1.0 |
hwGBondBondStateChangeTrapBond status change trap.
This notification indicates trap when bond status changes. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.137.3.1.0.1 |
hwGBondBondProfileChangeTrapBonding group profile ID change trap.
This notification indicates trap when bonding group profile ID changes. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.137.3.1.0.2 |
hwGBondAlarmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.3.2 |
hwGBondAlarmTrapsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.3.2.0 |
hwGBondLowUpRateCrossingAlarmTrapThis notification indicates that the G.Bond port upstream
data rate has reached/dropped below or exceeded the low
upstream rate threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.137.3.2.0.1 |
hwGBondLowDownRateCrossingAlarmTrapThis notification indicates that the G.Bond port downstream
data rate has reached/dropped below or exceeded the low
downstream rate threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.137.3.2.0.2 |
hwGBondInvalidCpeAlarmTrapThis notification indicates that the G.Bond port connects with a
invalid CPE. NOTIFICATION-TYPE .1.3.6.1.4.1.2011.6.137.3.2.0.3 |
hwGBondTrapsVbOids OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.4 |
hwGBondProfileIDThe bonding group profile ID.ro Integer32 .1.3.6.1.4.1.2011.6.137.4.1 |
hwGBondGroupIDThe bonding group ID.ro Integer32 .1.3.6.1.4.1.2011.6.137.4.2 |
hwGBondEthPM OBJECT IDENTIFIER .1.3.6.1.4.1.2011.6.137.5 |
hwGBondEthPortPerfCurrTableThis table contains current performance monitoring information
for a G.Bond/Eth port. This table contains live data from the
equipment and as such is not persistent.
The index of this table is hwGBondPriPort. SEQUENCE OF HwGBondEthPortPerfCurrEntry .1.3.6.1.4.1.2011.6.137.5.1 |
hwGBondEthPortPerfCurrEntryThis table contains current performance monitoring information
for a G.Bond/Eth port. This table contains live data from the
equipment and as such is not persistent.
The index of this entry is hwGBondPriPort. HwGBondEthPortPerfCurrEntry .1.3.6.1.4.1.2011.6.137.5.1.1 |
hwGBondEthPortPerfCurr15MinStartTimeStart time of the current 15-minute statistics performance.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.5.1.1.1 |
hwGBondEthPortPerf15MinValidIntervalsA read-only number of 15-minute intervals for which the
performance data was collected. The value of this object will
be 96 or the maximum number of 15-minute history intervals
collected by the implementation unless the measurement was
(re-)started recently, in which case the value will be the
number of complete 15 minutes intervals for which there are at
least some data.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.2 |
hwGBondEthPortPerf15MinInvalidIntervalsA read-only number of 15-minute intervals for which the
performance data was not always available. The value will
typically be zero except in cases where the data for some
intervals are not available.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.3 |
hwGBondEthPortPerfCurr15MinTimeElapsedA read-only count of seconds that have elapsed since the
beginning of the current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.4 |
hwGBondEthPortPerfCurr15MinRxErrorsA read-only count of errored fragments received and discarded
by a G.Bond/Eth port, during the current 15-minute performance
interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.5 |
hwGBondEthPortPerfCurr15MinRxSmallFragmentsA read-only count of fragments smaller than minFragmentSize
(64 Bytes), that have been received and discarded by a
G.Bond/Eth port, during the current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.6 |
hwGBondEthPortPerfCurr15MinRxLargeFragmentsA read-only count of fragments larger than maxFragmentSize
(512 Bytes), that have been received and discarded by a
G.Bond/Eth port, during the current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.7 |
hwGBondEthPortPerfCurr15MinRxBadFragmentsA read-only count of fragments which do not fit into the
sequence expected by the frame assembly function, that have been
received and discarded by a G.Bond/Eth port, during the current
15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.8 |
hwGBondEthPortPerfCurr15MinRxLostFragmentsA read-only count of gaps in the sequence of fragments,
expected by the frame assembly function of a G.Bond/Eth port,
during the current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.9 |
hwGBondEthPortPerfCurr15MinRxLostStartsA read-only count of missing StartOfPacket indicators expected
by the frame assembly function of a G.Bond/Eth port, during the
current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.10 |
hwGBondEthPortPerfCurr15MinRxLostEndsA read-only count of missing EndOfPacket indicators expected
by the frame assembly function of a G.Bond/Eth port, during the
current 15-minute performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.11 |
hwGBondEthPortPerfCurr15MinRxOverflowsA read-only count of fragments that have been received and
discarded by a G.Bond/Eth port, which would have caused the
frame assembly buffer to overflow, during the current 15-minute
performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.12 |
hwGBondEthPortPerfCurr1DayStartTimeStart time of the current 1-day statistics performance.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.5.1.1.13 |
hwGBondEthPortPerf1DayValidIntervalsA read-only number of 1-day intervals for which data was
collected. The value of this object will be 7 or the maximum
number of 1-day history intervals collected by the
implementation unless the measurement was (re-)started recently,
in which case the value will be the number of complete 1-day
intervals for which there are at least some data.
In certain cases it is possible that some intervals are
unavailable. In this case, this object reports the maximum
interval number for which data is available.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.14 |
hwGBondEthPortPerf1DayInvalidIntervalsA read-only number of 1-day intervals for which data was
not always available. The value will typically be zero except in
cases where the data for some intervals are not available.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.15 |
hwGBondEthPortPerfCurr1DayTimeElapsedA read-only count of seconds that have elapsed since the
beginning of the current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.16 |
hwGBondEthPortPerfCurr1DayRxErrorsA read-only count of errored fragments received and discarded
by a G.Bond/Eth port, during the current 1-day performance intervalro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.17 |
hwGBondEthPortPerfCurr1DayRxSmallFragmentsA read-only count of fragments smaller than minFragmentSize
(64 Bytes), that have been received and discarded by a
G.Bond/Eth port, during the current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.18 |
hwGBondEthPortPerfCurr1DayRxLargeFragmentsA read-only count of fragments larger than maxFragmentSize
(512 Bytes), that have been received and discarded by a
G.Bond/Eth port, during the current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.19 |
hwGBondEthPortPerfCurr1DayRxBadFragmentsA read-only count of fragments which do not fit into the
sequence expected by the frame assembly function, that have been
received and discarded by a G.Bond/Eth port, during the current
1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.20 |
hwGBondEthPortPerfCurr1DayRxLostFragmentsA read-only count of gaps in the sequence of fragments,
expected by the frame assembly function of a G.Bond/Eth port,
during the current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.21 |
hwGBondEthPortPerfCurr1DayRxLostStartsA read-only count of missing StartOfPacket indicators expected
by the frame assembly function of a G.Bond/Eth port, during the
current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.22 |
hwGBondEthPortPerfCurr1DayRxLostEndsA read-only count of missing EndOfPacket indicators expected
by the frame assembly function of a G.Bond/Eth port, during the
current 1-day performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.23 |
hwGBondEthPortPerfCurr1DayRxOverflowsA read-only count of fragments that have been received and
discarded by a G.Bond/Eth port, which would have caused the
frame assembly buffer to overflow, during the current 1-day
performance interval.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.24 |
hwGBondEthPortPerfRxErrorsA number of fragments that have been received across the
gamma interface and discarded.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.25 |
hwGBondEthPortPerfRxSmallFragmentsA number of fragments smaller than minFragmentSize
(64 Bytes), that have been received across the gamma
interface and discarded.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.26 |
hwGBondEthPortPerfRxLargeFragmentsA number of fragments larger than maxFragmentSize
(512 Bytes), which have been received across the gamma
interface and discarded.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.27 |
hwGBondEthPortPerfRxBadFragmentsA number of fragments which do not fit into the sequence
expected by the frame assembly function, that have been
received across the gamma interface and discarded (the
frame buffer is flushed to the next valid frame start)ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.28 |
hwGBondEthPortPerfRxLostFragmentsA number of gaps in the sequence of fragments, which have
been received across the gamma interface (the frame buffer is
flushed to the next valid frame start, when fragment/fragments
expected by the frame assembly function is/are not received).ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.29 |
hwGBondEthPortPerfRxLostStartsA number of missing StartOfPacket indicators expected by the
frame assembly function.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.30 |
hwGBondEthPortPerfRxLostEndsA number of missing EndOfPacket indicators expected by the
frame assembly function.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.31 |
hwGBondEthPortPerfRxOverflowsA number of fragments, received across the gamma interface
and discarded, which would have caused the frame assembly
buffer to overflow.ro Gauge32 .1.3.6.1.4.1.2011.6.137.5.1.1.32 |
hwGBondGroupProfTableThe table hwGBondGroupProfTable contains the bonding group profile
configuration.
A default profile with an index of 'DEFVAL' will always exist and
its parameters will be set to vendor-specific values, unless otherwise
specified in this document.
The index of this table is hwGBondGroupProfName. SEQUENCE OF HwGBondGroupProfEntry .1.3.6.1.4.1.2011.6.137.6 |
hwGBondGroupProfEntryThe table hwGBondGroupProfTable contains the bonding group profile
configuration.
A default profile with an index of 'DEFVAL' will always exist and
its parameters will be set to vendor-specific values, unless otherwise
specified in this document.
The index of this entry is hwGBondGroupProfName. HwGBondGroupProfEntry .1.3.6.1.4.1.2011.6.137.6.1 |
hwGBondGroupProfNameThis object identifies a row in this table. OCTET STRING .1.3.6.1.4.1.2011.6.137.6.1.1 |
hwGBondGroupProfMaxDelayUsThis parameter is the maximum one-way interleaving delay introduced
by the PMS-TC on upstream direction.rw Gauge32 .1.3.6.1.4.1.2011.6.137.6.1.2 |
hwGBondGroupProfMaxDelayDsThis parameter is the maximum one-way interleaving delay introduced
by the PMS-TC on downstream direction.rw Gauge32 .1.3.6.1.4.1.2011.6.137.6.1.3 |
hwGBondGroupProfMinProtectionUsThis parameter is minimum impulse noise protection for the bearer channel
in the upstream direction, expressed in symbols. The parameter can take the
following values: noProtection (i.e., INP not required), halfSymbol(i.e., INP
length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol.rw GBondSymbolProtection UNITS "symbols" .1.3.6.1.4.1.2011.6.137.6.1.4 |
hwGBondGroupProfMinProtectionDsThis parameter is minimum impulse noise protection for the bearer channel
in the downstream direction, expressed in symbols. The parameter can take the
following values: noProtection (i.e., INP not required), halfSymbol(i.e., INP
length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol.rw GBondSymbolProtection UNITS "symbols" .1.3.6.1.4.1.2011.6.137.6.1.5 |
hwGBondGroupProfMinDataRateUsThis parameter specifics minimum data rate for the bearer channel
in the upstream direction. The value of 0 means that the minimum
upstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.6 |
hwGBondGroupProfMinDataRateDsThis parameter specifics minimum data rate for the bearer channel
in the downstream direction. The value of 0 means that the minimum
downstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.7 |
hwGBondGroupProfMaxDataRateUsThis parameter specifics maximum data rate for the bearer channel
in the upstream direction. The value of 0 means that the maximum
upstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.8 |
hwGBondGroupProfMaxDataRateDsThis parameter specifics maximum data rate for the bearer channel
in the downstream direction. The value of 0 means that the maximum
downstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.9 |
hwGBondGroupProfTargetDataRateUsA desired G.Bond port data rate in the upstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
configuration settings. This object represents a sum of individual
BCE upstream data rates, modified to compensate for fragmentation
and encapsulation overhead (e.g., for an Ethernet service, the
target data rate of 10Mbps shall allow lossless transmission
of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap).
The value between 64 and 200000 indicates that the total
upstream data rate of the G.Bond port after initialization
SHALL be equal to the target data rate or less, if the target
upstream data rate cannot be achieved under the restrictions
configured for BCEs. In case the copper environment allows to
achieve higher upstream data rate than that specified by this
object, the excess capability shall be either converted to
additional SNR margin or reclaimed by minimizing transmit power.
The value of 0 means that the target data rate is not
fixed and SHALL be set to the maximum attainable rate during
initialization (Best Effort), under specified spectral
restrictions and with desired SNR Margin per BCE.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.10 |
hwGBondGroupProfTargetDataRateDsA desired G.Bond port data rate in the downstream direction,
in Kbps, to be achieved during initialization, under
restrictions placed upon the member BCEs by their respective
configuration settings. This object represents a sum of individual
BCE downstream data rates, modified to compensate for fragmentation
and encapsulation overhead (e.g., for an Ethernet service, the
target data rate of 10Mbps shall allow lossless transmission
of full-duplex 10Mbps Ethernet frame stream with minimal inter-frame gap).
The value between 64 and 200000 indicates that the total
downstream data rate of the G.Bond port after initialization
SHALL be equal to the target data rate or less, if the target
downstream data rate cannot be achieved under the restrictions
configured for BCEs. In case the copper environment allows to
achieve higher downstream data rate than that specified by
this object, the excess capability shall be either converted
to additional SNR margin or reclaimed by minimizing transmit power.
The value of 0 means that the target data rate is not
fixed and SHALL be set to the maximum attainable rate during
initialization (Best Effort), under specified spectral
restrictions and with desired SNR Margin per BCE.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.11 |
hwGBondGroupProfThreshLowDataRateUsThis object configures the G.Bond port low upstream rate
crossing alarm threshold. The value of 0 means that the
low upstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.12 |
hwGBondGroupProfThreshLowDataRateDsThis object configures the G.Bond port low downstream rate
crossing alarm threshold. The value of 0 means that the
low downstream data rate is not fixed.rw Gauge32 (0 | 64..200000) UNITS "Kbps" .1.3.6.1.4.1.2011.6.137.6.1.13 |
hwGBondGroupProfLowRateCrossingEnableIndicates whether hwGBondLowUpRateCrossingAlarmTrap and hwGBondLowDownRateCrossingAlarmTrap
notifications should be generated for this interface.
Options:
1. enable(1) - Indicates that the notifications are enabled
2. disable(2) - Indicates that the notifications are disabledrw Enumeration .1.3.6.1.4.1.2011.6.137.6.1.14 |
hwGBondGroupProfRowStatusThis object is used to create a new row or delete an existing row
in this table. Before a profile can be deleted, it must be not
referenced from all associated bonding group.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2011.6.137.6.1.15 |
hwGBondGroupProfBondCpeIncorrectAlarmSwitchThis object enable/disable the bonding CPE incorrect alarm switch.
Options:
1. enable(1) - The bonding CPE incorrect alarm switch is enabled
2. disable(2) - The bonding CPE incorrect alarm switch is disabledrw Enumeration .1.3.6.1.4.1.2011.6.137.6.1.16 |