HP-SN-MPLS-TE-MIB
This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in:
1. Extensions to RSVP for LSP Tunnels, Awduche et
al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001
3. Requirements for Traffic Engineering Over MPLS,
Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, RFC 2702, September 1999
Main OID:
mplsTeMIB.1.3.6.1.4.1.1991.1.2.15.15.3
128
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
128 total| Object Name |
|---|
mplsTeMIBThis MIB module contains managed object definitions
for MPLS Traffic Engineering (TE) as defined in:
1. Extensions to RSVP for LSP Tunnels, Awduche et
al, RFC 3209, December 2001
2. Constraint-Based LSP Setup using LDP, Jamoussi
(Editor), Internet Draft <draft-ietf-mpls-cr-ldp-
06.txt>, November 2001
3. Requirements for Traffic Engineering Over MPLS,
Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M.,
and J. McManus, RFC 2702, September 1999 MODULE-IDENTITY .1.3.6.1.4.1.1991.1.2.15.15.3 |
mplsTeScalars OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.1 |
mplsTunnelConfiguredThe number of tunnels configured on this device. A
tunnel is considered configured if the
mplsTunnelRowStatus is active(1).ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.1.1 |
mplsTunnelActiveThe number of tunnels active on this device. A
tunnel is considered active if the
mplsTunnelOperStatus is up(1).ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.1.2 |
mplsTunnelTEDistProtoThe traffic engineering distribution protocol(s)
used by this LSR. Note that an LSR may support more
than one distribution protocol simultaneously.ro Bits .1.3.6.1.4.1.1991.1.2.15.15.3.1.3 |
mplsTunnelMaxHopsThe maximum number of hops that can be specified for
a tunnel on this device.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.1.4 |
mplsTeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.2 |
mplsTunnelIndexNextThis object contains the next appropriate value to
be used for mplsTunnelIndex when creating entries
in mplsTunnelTable. If the number of unassigned
entries is exhausted, a retrival operation will
return a value of 0. This object may also return a
value of 0 when the LSR is unable to accept
conceptual row creation, for example, if the
mplsTunnelTable is implemented as read-only. To
obtain the value of mplsTunnelIndex for a new
entry, the manager must first issue a management
protocol retrieval operation to obtain the current
value of this object. The agent should modify the
value to reflect the next unassigned index after
each retrieval operation. After a manager retrieves
a value the agent will determine through its local
policy when this index value will be made available
for reuse.ro Integer32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.1 |
mplsTunnelTableThe mplsTunnelTable allows new MPLS tunnels to be
created between an LSR and a remote endpoint, and
existing tunnels to be reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and point-
to-multi-point connections are supported by an LSR
acting as a cross-connect. Each MPLS tunnel can
thus have one out-segment originating at this LSR
and/or one in-segment terminating at this LSR. SEQUENCE OF MplsTunnelEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.2 |
mplsTunnelEntryAn entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol. Whenever a new entry is created
with mplsTunnelIsIf set to true(1), then a
corresponding entry is created in ifTable as well
(see RFC 2863). The ifType of this entry is
mplsTunnel(150). MplsTunnelEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1 |
mplsTunnelIndexUniquely identifies this row. MplsTunnelIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.1 |
mplsTunnelInstanceUniquely identifies an instance of a tunnel. It is
useful to identify multiple instances of tunnels
for the purposes of backup and parallel tunnels. MplsTunnelInstanceIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.2 |
mplsTunnelIngressLSRIdThe purpose of this object is to uniquely identity a
tunnel within a network. When the MPLS signalling
protoocol is rsvp(2) this value SHOULD mimic the
Extended Tunnel Id field in the SESSION object.
When the MPLS signalling protoocol is crldp(3) this
value SHOULD mimic the Ingress LSR Router ID field
in the LSPID TLV object. MplsLsrIdentifier (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.3 |
mplsTunnelEgressLSRIdSpecifies the egress LSR ID. MplsLsrIdentifier (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.4 |
mplsTunnelNameThe canonical name assigned to the tunnel. This name
can be used to refer to the tunnel on the LSR's
console port. If mplsTunnelIsIf is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.5 |
mplsTunnelDescrA textual string containing information about the
tunnel. If there is no description this object
contains a zero length string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.6 |
mplsTunnelIsIfDenotes whether or not this tunnel corresponds to an
interface represented in the interfaces group
table. Note that if this variable is set to true
then the ifName of the interface corresponding to
this tunnel should have a value equal to
mplsTunnelName. Also see the description of ifName
in RFC 2863.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.7 |
mplsTunnelIfIndexIf mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which corresponds
to an entry in the interfaces table. Otherwise
this variable should contain the value of zero
indicating that a valid ifIndex was not assigned to
this tunnel interface.ro InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.8 |
mplsTunnelXCPointerThis variable points to a row in the mplsXCTable.
This table identifies the segments that compose
this tunnel, their characteristics, and
relationships to each other. A value of zeroDotZero
indicates that no LSP has been associated with this
tunnel yet.rw RowPointer (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.9 |
mplsTunnelSignallingProtoThe signaling protocol, if any, which was used to
setup this tunnel.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.10 |
mplsTunnelSetupPrioIndicates the setup priority of this tunnel.rw Integer32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.11 |
mplsTunnelHoldingPrioIndicates the holding priority for this tunnel.rw Integer32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.12 |
mplsTunnelSessionAttributesThis bitmask indicates optional session values for
this tunnel. The following describes these
bitfields:
fastRerouteThis flag indicates that the any tunnel
hop may choose to reroute this tunnel without
tearing it down. This flag permits transit routers
to use a local repair mechanism which may result in
violation of the explicit routing of this tunnel.
When a fault is detected on an adjacent downstream
link or node, a transit router can reroute traffic
for fast service restoration.
mergingPermitted This flag permits transit routers
to merge this session with other RSVP sessions for
the purpose of reducing resource overhead on
downstream transit routers, thereby providing
better network scalability.
isPersistent Indicates whether this tunnel should
be restored automatically after a failure occurs.
isPinned This flag indicates whether the loose-
routed hops of this tunnel are to be pinned.
recordRouteThis flag indicates whether or not the
signaling protocol should remember the tunnel path
after it has been signaled.rw Bits .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.13 |
mplsTunnelOwnerIndicates which protocol created and is responsible
for managing this tunnel. Values rsvp(2) and
crldp(3) should not be used at the head-end of a
MPLS tunnel.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.14 |
mplsTunnelLocalProtectInUseIndicates that the local repair mechanism is in use
to maintain this tunnel (usually in the face of an
outage of the link it was previously routed over).rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.15 |
mplsTunnelResourcePointerThis variable represents a pointer to the traffic
parameter specification for this tunnel. This
value may point at an entry in the
mplsTunnelResourceEntry to indicate which
mplsTunnelResourceEntry is to be assigned to this
segment. This value may optionally point at an
externally defined traffic parameter specification
table. A value of zeroDotZero indicates best-
effort treatment. By having the same value of this
object, two or more segments can indicate resource
sharing.rw RowPointer (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.16 |
mplsTunnelInstancePriorityThis value indicates which priority, in descending
order, with 0 indicating the lowest priority,
within a group of tunnel instances. A group of
tunnel instances is defined as a set of tunnels
with the same mplsTunnelIndex in this table, but
with a different mplsTunnelInstance. Tunnel group
priorities are used to denote the priority at which
a particular tunnel instance will supercede
another. Instances of tunnels containing the same
mplsTunnelInstancePriority will be used for load
sharing.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.17 |
mplsTunnelHopTableIndexIndex into the mplsTunnelHopTable entry that
specifies the explicit route hops for this tunnel.rw MplsPathIndexOrZero (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.18 |
mplsTunnelARHopTableIndexIndex into the mplsTunnelARHopTable entry that
specifies the actual hops traversed by the tunnel.ro MplsPathIndexOrZero (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.19 |
mplsTunnelCHopTableIndexIndex into the mplsTunnelCHopTable entry that
specifies the computed hops traversed by the
tunnel.ro MplsPathIndexOrZero (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.20 |
mplsTunnelPrimaryInstanceSpecifies the instance index of the primary instance
of this tunnel.ro MplsTunnelInstanceIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.21 |
mplsTunnelPrimaryTimeUpSpecifies the total time the primary instance of
this tunnel has been active. The primary instance
of this tunnel is defined in
mplsTunnelPrimaryInstance.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.22 |
mplsTunnelPathChangesSpecifies the number of times the paths has changed
for this tunnel.ro Counter32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.23 |
mplsTunnelLastPathChangeSpecifies the time since the last path change for
this tunnel.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.24 |
mplsTunnelCreationTimeSpecifies the value of SysUpTime when the first
instance of this tunnel came into existence.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.25 |
mplsTunnelStateTransitionsSpecifies the number of times the state of this
tunnel instance has changed.ro Counter32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.26 |
mplsTunnelIncludeAnyAffinityA link satisfies the include-any constraint if and
only if the constraint is zero, or the link and the
constraint have a resource class in common.rw MplsTunnelAffinity (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.27 |
mplsTunnelIncludeAllAffinityA link satisfies the include-all constraint if and
only if the link contains all of the adminstrative
groups specified in the constraint.rw MplsTunnelAffinity (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.28 |
mplsTunnelExcludeAllAffinityA link satisfies the exclude-all constraint if and
only if the link contains none of the adminstrative
groups specifie in the constraint.rw MplsTunnelAffinity (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.29 |
mplsTunnelPathInUseThis value denotes the configured path that was
chosen for this tunnel. This value reflects the
secondary index into mplsTunnelHopTable. This path
may not exactly match the one in
mplsTunnelARHopTable due to the fact that some CSPF
modification may have taken place. See
mplsTunnelARHopTable for the actual path being
taken by the tunnel. A value of zero denotes that
no path is currently in use or available.rw MplsPathIndexOrZero (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.30 |
mplsTunnelRoleThis value signifies the role that this tunnel
entry/instance represents. This value MUST be set
to head(1) at the originating point of the tunnel.
This value MUST be set to transit(2) at transit
points along the tunnel, if transit points are
supported. This value MUST be set to tail(3) at the
terminating point of the tunnel if tunnel tails are
supported.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.31 |
mplsTunnelTotalUpTimeThis value represents the aggregate up time for all
instances of this tunnel, if available. If this
value is unavailable, it MUST return a value of 0.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.32 |
mplsTunnelInstanceUpTimeThis value identifies the total time that this
tunnel instance's operStatus has been Up(1).rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.33 |
mplsTunnelAdminStatusIndicates the desired operational status of this
tunnel.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.34 |
mplsTunnelOperStatusIndicates the actual operational status of this
tunnel, which is typically but not limited to, a
function of the state of individual segments of
this tunnel.ro Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.35 |
mplsTunnelRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.36 |
mplsTunnelStorageTypeThis variable indicates the storage type for this
object.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.2.1.37 |
mplsTunnelHopListIndexNextThis object contains an appropriate value to be used
for mplsTunnelHopListIndex when creating entries in
the mplsTunnelHopTable. If the number of
unassigned entries is exhausted, a retrival
operation will return a value of 0. This object
may also return a value of 0 when the LSR is unable
to accept conceptual row creation, for example, if
the mplsTunnelHopTable is implemented as read-only.
To obtain the value of mplsTunnelHopListIndex for a
new entry in the mplsTunnelHopTable, the manager
issues a management protocol retrieval operation to
obtain the current value of mplsTunnelHopIndex.
After each retrieval operation, the agent should
modify the value to reflect the next unassigned
index. After a manager retrieves a value the agent
will determine through its local policy when this
index value will be made available for reuse.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.3 |
mplsTunnelHopTableThe mplsTunnelHopTable is used to indicate the hops,
strict or loose, for an MPLS tunnel defined in
mplsTunnelTable, when it is established via
signaling, for the outgoing direction of the
tunnel. Each row in this table is indexed by
mplsTunnelHopListIndex. Each row also has a
secondary index mplsTunnelHopIndex corresponding to
the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelHopTable. SEQUENCE OF MplsTunnelHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.4 |
mplsTunnelHopEntryAn entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol. MplsTunnelHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1 |
mplsTunnelHopListIndexPrimary index into this table identifying a
particular explicit route object. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.1 |
mplsTunnelHopPathOptionIndexSecondary index into this table identifying a
particular group of hops representing a particular
configured path. This is otherwise known as a path
option. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.2 |
mplsTunnelHopIndexSecondary index into this table identifying a
particular hop. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.3 |
mplsTunnelHopAddrTypeDenotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.4 |
mplsTunnelHopIpv4AddrIf mplsTunnelHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. If mplsTunnelHopAddrType is set to lspid(4),
then this value will contain the Ingress LSR Router
ID of the Tunnel. This object is otherwise
insignificant and should contain a value of 0.rw InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.5 |
mplsTunnelHopIpv4PrefixLenIf mplsTunnelHopAddrType is ipV4(1), then the prefix
length for this hop's IPv4 address is contained
herein. This object is otherwise insignificant and
should contain a value of 0.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.6 |
mplsTunnelHopIpv6AddrIf the mplsTunnelHopAddrType is set to ipV6(2), then
this variable contains the IPv6 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.7 |
mplsTunnelHopIpv6PrefixLenIf mplsTunnelHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.8 |
mplsTunnelHopAsNumberIf mplsTunnelHopAddrType is set to asNumber(3), then
this value will contain the AS number of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.9 |
mplsTunnelHopLspIdIf mplsTunnelHopAddrType is set to lspid(4), then
this value will contain the LSPID of a tunnel of
this hop. The present tunnel being configured is
tunneled through this hop (using label stacking).
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.rw MplsLSPID (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.10 |
mplsTunnelHopTypeDenotes whether this tunnel hop is routed in a
strict or loose fashion.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.11 |
mplsTunnelHopIncludeExcludeIf this value is set to include(1), then this
indicates that this hop must be included in the
tunnel's path. If this value is set to exclude(2),
then this hop must be avoided when calculating the
path for this tunnel. The default value of this
object is include(1), so that by default all
indicated hops are included in the CSPF path
computation.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.12 |
mplsTunnelHopPathOptionNameThe description of this series of hops as they
relate to the specified path option.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.13 |
mplsTunnelHopEntryPathCompIf this value is set to dynamic, then the user
should only specify the source and destination of
the path and expect that the CSPF will calculate
the remainder of the path. If this value is set to
explicit, the user should specify the entire path
for the tunnel to take. This path may contain
strict or loose hops. Each hop along a specific
path should have this object set to the same valuerw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.14 |
mplsTunnelHopRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.15 |
mplsTunnelHopStorageTypeThis variable indicates the storage type for this
object.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.4.1.16 |
mplsTunnelResourceIndexNextThis object contains the next appropriate value to
be used for mplsTunnelResourceIndex when creating
entries in the mplsTunnelResourceTable. If the
number of unassigned entries is exhausted, a
retrival operation will return a value of 0. This
object may also return a value of 0 when the LSR is
unable to accept conceptual row creation, for
example, if the mplsTunnelTable is implemented as
read-only. To obtain the mplsTunnelResourceIndex
value for a new entry, the manager must first issue
a management protocol retrieval operation to obtain
the current value of this object. The agent should
modify the value to reflect the next unassigned
index after each retrieval operation. After a
manager retrieves a value the agent will determine
through its local policy when this index value will
be made available for reuse.ro Unsigned32 (0.. 2147483647) .1.3.6.1.4.1.1991.1.2.15.15.3.2.5 |
mplsTunnelResourceTableThe mplsTunnelResourceTable allows a manager to
specify which resources are desired for an MPLS
tunnel. This table also allows several tunnels to
point to a single entry in this table, implying
that these tunnels should share resources. SEQUENCE OF MplsTunnelResourceEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.6 |
mplsTunnelResourceEntryAn entry in this table represents a set of resources
for an MPLS tunnel. An entry can be created by a
network administrator or by an SNMP agent as
instructed by any MPLS signaling protocol. MplsTunnelResourceEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1 |
mplsTunnelResourceIndexUniquely identifies this row. Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.1 |
mplsTunnelResourceMaxRateThe maximum rate in bits/second. Note that setting
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate, and
mplsTunnelResourceMaxBurstSize to 0 indicates best-
effort treatment.
This object is copied to an instance of
mplsTrafficParamMaxRate in mplsTrafficParamTable
the OID of which is copied into the corresponding
mplsInSegmentTrafficParamPtr.rw MplsBitRate UNITS "bits per second" .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.2 |
mplsTunnelResourceMeanRateThis object is copied into an instance of
mplsTrafficParamMeanRate in the
mplsTrafficParamTable. The OID of this table entry
is then copied into the corresponding
mplsInSegmentTrafficParamPtr.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry in
mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMeanRate to mplsTrafficParamMeanRate.
The OID of this entry is copied to
mplsInSegmentTrafficParamPtr of the corresponding
in-segment entry.rw MplsBitRate UNITS "bits per second" .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.3 |
mplsTunnelResourceMaxBurstSizeThe maximum burst size in bytes. This object is
copied to mplsInSegmentMaxBurstSize of the
corresponding in-segment.
When resource allocation is performed as requested
by this TSpec object, it is copied into an entry in
mplsTrafficParamTable [LSRMIB]:
mplsTunnelInMaxBurstSize to
mplsTrafficParamMaxBurstSize. The OID of this entry
is copied to mplsInSegmentTrafficParamPtr of the
corresponding in-segment entry.rw MplsBurstSize UNITS "bytes" .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.4 |
mplsTunnelResourceMeanBurstSizeThe mean burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value.rw MplsBurstSize UNITS "bytes" .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.5 |
mplsTunnelResourceExcessBurstSizeThe Excess burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value.rw MplsBurstSize UNITS "bytes" .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.6 |
mplsTunnelResourceFrequencyThe granularity of the availability of committed
rate. The implementations which do not implement
this variable must return unspecified(1) for this
value and must not allow a user to set this value.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.7 |
mplsTunnelResourceWeightThe relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.8 |
mplsTunnelResourceRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.9 |
mplsTunnelResourceStorageTypeThis variable indicates the storage type for this
object.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.6.1.10 |
mplsTunnelARHopTableThe mplsTunnelARHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as reported by the MPLS
signaling protocol, for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelARHopListIndex. Each row also has a
secondary index mplsTunnelARHopIndex, corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelARHopTable.
Please note that since the information necessary to
build entries within this table are not provided by
some MPLS signaling protocols, implementation of
this table is optional. Furthermore, since the
information in this table is actually provided by
the MPLS signaling protocol after the path has been
set-up, the entries in this table are provided only
for observation, and hence, all variables in this
table are accessible exclusively as read-only. SEQUENCE OF MplsTunnelARHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.7 |
mplsTunnelARHopEntryAn entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol. MplsTunnelARHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1 |
mplsTunnelARHopListIndexPrimary index into this table identifying a
particular recorded hop list. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.1 |
mplsTunnelARHopIndexSecondary index into this table identifying the
particular hop. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.2 |
mplsTunnelARHopAddrTypeDenotes the address type of this tunnel hop.ro Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.3 |
mplsTunnelARHopIpv4AddrIf mplsTunnelARHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.4 |
mplsTunnelARHopIpv4PrefixLenIf mplsTunnelARHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.5 |
mplsTunnelARHopIpv6AddrIf the mplsTunnelARHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.6 |
mplsTunnelARHopIpv6PrefixLenIf mplsTunnelARHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.7 |
mplsTunnelARHopAsNumberIf mplsTunnelARHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.8 |
mplsTunnelARHopLspIdIf mplsTunnelARHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.ro MplsLSPID (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.7.1.9 |
mplsTunnelCHopTableThe mplsTunnelCHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as computed by a constraint-
based routing protocol, based on the
mplsTunnelHopTable for the outgoing direction of
the tunnel. Each row in this table is indexed by
mplsTunnelCHopListIndex. Each row also has a
secondary index mplsTunnelCHopIndex, corresponding
to the next hop that this row corresponds to. The
first row in the table is the first hop after the
origination point of the tunnel. In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelCHopTable.
Please note that since the information necessary to
build entries within this table may not be
supported by some LSRs, implementation of this
table is optional. Furthermore, since the
information in this table is actually provided by
routing protocol after the path has been computed,
the entries in this table are provided only for
observation, and hence, all variables in this table
are accessible exclusively as read-only. SEQUENCE OF MplsTunnelCHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.8 |
mplsTunnelCHopEntryAn entry in this table represents a tunnel hop. An
entry in this table is created by a constraint-
based routing protocol based on the hops specified
in the corresponding mplsTunnelHopTable. MplsTunnelCHopEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1 |
mplsTunnelCHopListIndexPrimary index into this table identifying a
particular computed hop list. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.1 |
mplsTunnelCHopIndexSecondary index into this table identifying the
particular hop. MplsPathIndex (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.2 |
mplsTunnelCHopAddrTypeDenotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP.ro Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.3 |
mplsTunnelCHopIpv4AddrIf mplsTunnelCHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.ro InetAddressIPv4 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.4 |
mplsTunnelCHopIpv4PrefixLenIf mplsTunnelCHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.5 |
mplsTunnelCHopIpv6AddrIf the mplsTunnelCHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.6 |
mplsTunnelCHopIpv6PrefixLenIf mplsTunnelCHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.7 |
mplsTunnelCHopAsNumberIf mplsTunnelCHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact.ro Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.8 |
mplsTunnelCHopLspIdIf mplsTunnelCHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.ro MplsLSPID (HP-SN-MPLS-TC-MIB) .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.9 |
mplsTunnelCHopTypeDenotes whether this is tunnel hop is routed in a
strict or loose fashion.ro Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.8.1.10 |
mplsTunnelPerfTableThis table provides per-tunnel MPLS performance
information. SEQUENCE OF MplsTunnelPerfEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.9 |
mplsTunnelPerfEntryAn entry in this table is created by the LSR for
every tunnel. Its is an extension to
mplsTunnelEntry. MplsTunnelPerfEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1 |
mplsTunnelPerfPacketsNumber of packets forwarded by the tunnel.ro Counter32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1.1 |
mplsTunnelPerfHCPacketsHigh capacity counter for number of packets
forwarded by the tunnel.ro Counter64 .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1.2 |
mplsTunnelPerfErrorsNumber of errored packets.ro Counter32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1.3 |
mplsTunnelPerfBytesNumber of bytes forwarded by the tunnel.ro Counter32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1.4 |
mplsTunnelPerfHCBytesHigh capacity counter for number of bytes forwarded
by the tunnel.ro Counter64 .1.3.6.1.4.1.1991.1.2.15.15.3.2.9.1.5 |
mplsTunnelCRLDPResTableThe mplsTunnelCRLDPResTable allows a manager to
specify which CR-LDP-specific resources are desired
for an MPLS tunnel if that tunnel is signaled using
CR-LDP. Note that these attributes are in addition
to those specified in mplsTunnelResourceTable. This
table also allows several tunnels to point to a
single entry in this table, implying that these
tunnels should share resources. SEQUENCE OF MplsTunnelCRLDPResEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.10 |
mplsTunnelCRLDPResEntryAn entry in this table represents a set of resources
for an MPLS tunnel established using CRLDP
(mplsTunnelSignallingProto equal to crldp (3)). An
entry can be created by a network administrator or
by an SNMP agent as instructed by any MPLS
signaling protocol. MplsTunnelCRLDPResEntry .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1 |
mplsTunnelCRLDPResMeanBurstSizeThe mean burst size in bytes.rw MplsBurstSize UNITS "bytes" .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.2 |
mplsTunnelCRLDPResExcessBurstSizeThe Excess burst size in bytes.rw MplsBurstSize UNITS "bytes" .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.3 |
mplsTunnelCRLDPResFrequencyThe granularity of the availability of committed
rate.rw Enumeration .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.4 |
mplsTunnelCRLDPResWeightThe relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.5 |
mplsTunnelCRLDPResFlagsThe value of the 1 byte Flags conveyed as part of
the traffic parameters during the establishment of
the CRLSP. The bits in this object are to be
interpreted as follows.
+++++
| Res |F6|F5|F4|F3|F2|F1|
+++++
Res - These bits are reserved. Zero on transmission.
Ignored on receipt.
F1 - Corresponds to the PDR.
F2 - Corresponds to the PBS.
F3 - Corresponds to the CDR.
F4 - Corresponds to the CBS.
F5 - Corresponds to the EBS.
F6 - Corresponds to the Weight.
Each flag if is a Negotiable Flag corresponding to a
Traffic Parameter. The Negotiable Flag value zero
denotes Not Negotiable and value one denotes
Negotiable.rw Unsigned32 .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.6 |
mplsTunnelCRLDPResRowStatusThis variable is used to create, modify, and/or
delete a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.7 |
mplsTunnelCRLDPResStorageTypeThis variable indicates the storage type for this
object.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.10.1.8 |
mplsTunnelTrapEnableIf this object is true, then it enables the
generation of mplsTunnelUp and mplsTunnelDown
traps, otherwise these traps are not emitted.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.1991.1.2.15.15.3.2.11 |
mplsTeNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.3 |
mplsTeNotifyPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.3.0 |
mplsTunnelUpThis notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to leave the down state
and transition into some other state (but not into
the notPresent state). This other state is
indicated by the included value of
mplsTunnelOperStatus. NOTIFICATION-TYPE .1.3.6.1.4.1.1991.1.2.15.15.3.3.0.1 |
mplsTunnelDownThis notification is generated when a
mplsTunnelOperStatus object for one of the
configured tunnels is about to enter the down state
from some other state (but not from the notPresent
state). This other state is indicated by the
included value of mplsTunnelOperStatus. NOTIFICATION-TYPE .1.3.6.1.4.1.1991.1.2.15.15.3.3.0.2 |
mplsTunnelReroutedThis notification is generated when a tunnel is
rerouted. If the actual path is used, then this
tunnel's entry MAY contain the new path for this
tunnel some time after this trap is issued by the
agent. NOTIFICATION-TYPE .1.3.6.1.4.1.1991.1.2.15.15.3.3.0.3 |
mplsTunnelReoptimizedThis notification is generated when a tunnel is
reoptimized. If the actual path is used, then this
tunnel's entry MAY contain the new path for this
tunnel some time after this trap is issued by the
agent. NOTIFICATION-TYPE .1.3.6.1.4.1.1991.1.2.15.15.3.3.0.4 |
mplsTeConformance OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.4 |
mplsTeGroups OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.4.1 |
mplsTeCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.1991.1.2.15.15.3.4.2 |