GALILEO-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for GALILEO-MIB.
166
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
166 total| Object Name |
|---|
rlGalMibVersionMIB's version, the current version is 1.ro INTEGER .1.3.6.1.4.1.89.56.1 |
rlGalModeCurrent mode supported by the device.ro Enumeration .1.3.6.1.4.1.89.56.2 |
rlGalModeAfterResetNew mode supported by the device after the next reset.rw Enumeration .1.3.6.1.4.1.89.56.3 |
rlPolicyGalileoDebugTuning OBJECT IDENTIFIER .1.3.6.1.4.1.89.56.4 |
rlPolicyGalileoTuningOverProvisioningFor non-quantitative flows:
Defines the function that is used to devide the aggregate rate
(dependent on the number of flows using the specific meterId).
The options for this mib variables are:
- overProvisioning is 1/n -> may cause severe exceeding from
permitted bw.
- minorOverProvisioning is 1/(n+1)-> may cause minor exceeding
from permitted bw.
- underProvisioning is 1/(2^n) -> usaully causes to be under
the permitted bw.
where n is the number of flows using the specific meterId, initial
value = 1.rw Enumeration .1.3.6.1.4.1.89.56.4.1 |
rlPolicyGalileoTuningExtremConditionBurstSizeThis variable indicates the value of a new burst size, when the given
aggregate burst size has reached the following extreme condition:
(aggregateBurstSize/n) < 1536 (smaller than max MTU).
The options for this mib variables are:
- new burst = 0 bytes
- new burst = 1536 bytes
where n is the number of flows using the specific meterId.rw Enumeration .1.3.6.1.4.1.89.56.4.2 |
rlPolicyGalileoTuningOverrideOutOfProfileDropPrecedenceThis mib variable is used only when the
rlPolicyGalileoTuningExtremConditionBurstSize is 0 bytes.
The options for this mib variables are:
- TRUE => out of profile Drop Precedence = High Drop Precedence.
This value will override the rule's out of profile
Drop Precedence.
- FALSE => out of profile Drop Precedence is set according to
the rule's decision.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.4.3 |
rlCosFftAgingTimeoutThe aging timeout of the CoS FFT Tables.rw INTEGER .1.3.6.1.4.1.89.56.5 |
rlCosFftPollingIntervalThe polling interval for dynamic CoS FFTs support in seconds.rw INTEGER .1.3.6.1.4.1.89.56.6 |
rlPolicyGalileoDebug OBJECT IDENTIFIER .1.3.6.1.4.1.89.56.7 |
rlPolicyGalileoDebugFcogTableIndecate the instance of the fcog for hash_fnc calc per group type SEQUENCE OF RlPolicyGalileoDebugFcogEntry .1.3.6.1.4.1.89.56.7.1 |
rlPolicyGalileoDebugFcogEntrythe entry per groupType indicate the offsets for hash_func calc. RlPolicyGalileoDebugFcogEntry .1.3.6.1.4.1.89.56.7.1.1 |
rlPolicyGalileoDebugFcogTypeSpecifies a the Group type for which Fcog bytes specified.ro RlPolicyGalileoDebugGroupType .1.3.6.1.4.1.89.56.7.1.1.1 |
rlPolicyGalileoDebugL2SrcAddrindecate if the L2 SrcAddr defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.2 |
rlPolicyGalileoDebugL2DstAddrindecate if the L2DstAddr defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.3 |
rlPolicyGalileoDebugVlanIdindecate if the VlanId defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.4 |
rlPolicyGalileoDebugInportindecate if the Inport defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.5 |
rlPolicyGalileoDebugIpxDstNetindecate if the IpxDstNet defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.6 |
rlPolicyGalileoDebugIpxDstNodeindecate if the IpxDstNode defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.7 |
rlPolicyGalileoDebugIpSrcAddrindecate if the IpSrcAddr defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.8 |
rlPolicyGalileoDebugIpDstAddrindecate if the IpDstAddr defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.9 |
rlPolicyGalileoDebugIpProtocolindecate if the IpProtocol defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.10 |
rlPolicyGalileoDebugIpSrcPortindecate if the IpSrcPort defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.11 |
rlPolicyGalileoDebugIpDstPortindecate if the IpDstPort defined for fcog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.12 |
rlPolicyGalileoDebugStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.1.1.13 |
rlPolicyGalileoDebugFlowTableThis table will allow us to request variables from specific entry at the
flowTable. only get and getNext will be supported (getNext will return alyaws
EndOfMibTable) SEQUENCE OF RlPolicyGalileoDebugFlowTableEntry .1.3.6.1.4.1.89.56.7.2 |
rlPolicyGalileoDebugFlowTableEntryall the input fileds has a default val except from the groupType, request of an entry
should be based on the fcog definition. RlPolicyGalileoDebugFlowTableEntry .1.3.6.1.4.1.89.56.7.2.1 |
rlPolicyGalileoDebugFlowTypeSpecifies a the Group type.ro RlPolicyGalileoDebugGroupType .1.3.6.1.4.1.89.56.7.2.1.1 |
rlPolicyGalileoDebugFlowRxIfIndexSpecifies a the IfIndex the packet arrived (for the calculation
of the relevant cosTable.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.2 |
rlPolicyGalileoDebugFlowL2SrcAddrIndicate the L2SrcAddr for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.3 |
rlPolicyGalileoDebugFlowL2DstAddrIndicate the L2DstAddr for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.4 |
rlPolicyGalileoDebugFlowVlanIdIndicate the VlanId for the requsted entry.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.5 |
rlPolicyGalileoDebugFlowIpxDstNetIndicate the IPX DstNet for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.6 |
rlPolicyGalileoDebugFlowIpxDstNodeIndicate the IPX DstNode for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.7 |
rlPolicyGalileoDebugFlowIpSrcAddrIndicate the IP SrcAddr for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.8 |
rlPolicyGalileoDebugFlowIpDstAddrIndicate the IP DstAddr for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.9 |
rlPolicyGalileoDebugFlowIpProtocolIndicate the IP Protocol for the requsted entry.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.10 |
rlPolicyGalileoDebugFlowIpSrcPortIndicate the IP SrcPort for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.11 |
rlPolicyGalileoDebugFlowIpDstPortIndicate the IP DstPort for the requsted entry.ro OCTET STRING .1.3.6.1.4.1.89.56.7.2.1.12 |
rlPolicyGalileoDebugFlowRetValidIndicate if the requsted entry is valid (exist) or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.2.1.13 |
rlPolicyGalileoDebugFlowRetStaticIndicate if the requsted entry is a static entry or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.2.1.14 |
rlPolicyGalileoDebugFlowRetAgingIndicate if the Aging bit of the requested entry is set or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.2.1.15 |
rlPolicyGalileoDebugFlowRetCmdIndicate if the CMD of the requested entry .ro Enumeration .1.3.6.1.4.1.89.56.7.2.1.16 |
rlPolicyGalileoDebugFlowRetPrioIndicate if the Pri/Sc of the requested entry .ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.17 |
rlPolicyGalileoDebugFlowRetInProfileDisIndicate if the inProfile Discardability of the requested entry .ro Enumeration .1.3.6.1.4.1.89.56.7.2.1.18 |
rlPolicyGalileoDebugFlowRetVptIndicate if the Vpt of the requested entry .ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.19 |
rlPolicyGalileoDebugFlowRetChangeTosIndicate if the Change Tos of the requested entry is set or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.2.1.20 |
rlPolicyGalileoDebugFlowRetNewTosIndicate if the New Tos of the requested entry.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.21 |
rlPolicyGalileoDebugFlowRetVlanIdIndicate if the VlanId of the requested entry.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.22 |
rlPolicyGalileoDebugFlowRetInIfIndexIndicate if the InIfindex of the requested entry.ro INTEGER .1.3.6.1.4.1.89.56.7.2.1.23 |
rlPolicyGalileoDebugFlowRetEnableMeterIndicate if Meter of the requested entry is enbled or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.7.2.1.24 |
rlPolicyGalileoDebugFlowRetOutProfileDisIndicate the outProfile Discardability of the requested entry .ro Enumeration .1.3.6.1.4.1.89.56.7.2.1.25 |
rlPolicyGalileoFcuFwdCpuCounterCount the number of packets that forward from the Flow
Classification Unit to the CPUro INTEGER .1.3.6.1.4.1.89.56.8 |
rlPolicySimpleGalMib OBJECT IDENTIFIER .1.3.6.1.4.1.89.56.9 |
rlPolicySimpleGalMibVersionMIB's version, the current version is 1.ro INTEGER .1.3.6.1.4.1.89.56.9.1 |
rlPolicySimpleGalMibPortTypeSupportreturn a bit mask that indicates the supported port type:
|87654321|
1 - BoundaryType
2 - InteriorTypero OCTET STRING .1.3.6.1.4.1.89.56.9.2 |
rlPolicySimpleGalMibRecalculateRulesSetting any value will cause recalculation of all the rules.rw Enumeration .1.3.6.1.4.1.89.56.9.3 |
rlPolicySimpleGalMibPolicyEnableEnables or disables the policy featurerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.4 |
rlPolicySimpleGalMibProfileTableThe table defines all the profiles. SEQUENCE OF RlPolicySimpleGalMibProfileEntry .1.3.6.1.4.1.89.56.9.5 |
rlPolicySimpleGalMibProfileEntryThe entry define one profile. RlPolicySimpleGalMibProfileEntry .1.3.6.1.4.1.89.56.9.5.1 |
rlPolicySimpleGalMibIndexThis enumerates the table entry.ro INTEGER .1.3.6.1.4.1.89.56.9.5.1.1 |
rlPolicySimpleGalMibDescriptionInformational text given by the user to describe the profile.rw DisplayString .1.3.6.1.4.1.89.56.9.5.1.2 |
rlPolicySimpleGalMibProfileTypeSpecifies a profile type.rw RlPolicySimpleGalMibProfileType .1.3.6.1.4.1.89.56.9.5.1.3 |
rlPolicySimpleGalMibRateThe rate in kilobytes/second for the specified profile,
or in the case of minDelay per session profile type the rate will
indicate the rate per individual sessionrw INTEGER .1.3.6.1.4.1.89.56.9.5.1.4 |
rlPolicySimpleGalMibBurstSizeThe burst size parameter. A value of 0 means that
the device should choose the Burst Size
that is most suitable for the profile.rw INTEGER .1.3.6.1.4.1.89.56.9.5.1.5 |
rlPolicySimpleGalMibMaxSessionRelevant only for the minDelay per session.
Indicate the maximum number of sessions for this profile.rw INTEGER .1.3.6.1.4.1.89.56.9.5.1.6 |
rlPolicySimpleGalMibNewVptIndicates the new VPT to assign to the packet.rw INTEGER .1.3.6.1.4.1.89.56.9.5.1.7 |
rlPolicySimpleGalMibChangeTosOrDscpIndicates whether the TOS or DSCP should be remarked with
a new valuerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.5.1.8 |
rlPolicySimpleGalMibNewTosOrDscpIndicates the new value for the TOS or DSCP. Relevant only if
rlPolicySimpleGalMibChangeTosOrDscp is true.rw INTEGER .1.3.6.1.4.1.89.56.9.5.1.9 |
rlPolicySimpleGalMibStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.5.1.10 |
rlPolicySimpleGalMibIpFcogTableThis table defines the used fields for ip classification,
per port type (interior/boundary) SEQUENCE OF RlPolicySimpleGalMibIpFcogEntry .1.3.6.1.4.1.89.56.9.6 |
rlPolicySimpleGalMibIpFcogEntrythe entry define the used fields for classification RlPolicySimpleGalMibIpFcogEntry .1.3.6.1.4.1.89.56.9.6.1 |
rlPolicySimpleGalMibIpFcogPortTypeThe port type (interior/boundary) to which this entry applies.ro RlPolicySimpleGalMibPortType .1.3.6.1.4.1.89.56.9.6.1.1 |
rlPolicySimpleGalMibIpFcogTosOrDscpIndicates whether the IP TOS or DSCP field will be used in
classifiers or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.6.1.2 |
rlPolicySimpleGalMibIpFcogProtocolIndicates whether the IP L4 protocol field will be used in
classifiers or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.6.1.3 |
rlPolicySimpleGalMibIpFcogSrcIpMaskIndicates the number of most significant bits of the Ip Address
that are used in specifying IP source addresses in classifiers.rw INTEGER .1.3.6.1.4.1.89.56.9.6.1.4 |
rlPolicySimpleGalMibIpFcogDstIpMaskIndicates the number of most significant bits of the Ip Address
that are used in specifying IP destination addresses in classifiers.rw INTEGER .1.3.6.1.4.1.89.56.9.6.1.5 |
rlPolicySimpleGalMibIpFcogSrcPortIndicates whether the IP L4 protocol source port field will be used in
classifiers or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.6.1.6 |
rlPolicySimpleGalMibIpFcogDstPortIndicates whether the IP L4 protocol destination port field will be
used in classifiers or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.6.1.7 |
rlPolicySimpleGalMibIpFcogInIfIndexIndicates whether ifIndex of input ports will be used in
classifiers or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.6.1.8 |
rlPolicySimpleGalMibIpRulesTableThis table contains the policy rules defined by the user. The order
of the entries in the table is important, since the first rule that
applies to the incoming packet will be acted upon, ignoring any
further rules that may apply as well. SEQUENCE OF RlPolicySimpleGalMibIpRulesEntry .1.3.6.1.4.1.89.56.9.7 |
rlPolicySimpleGalMibIpRulesEntryThis entry defines one policy rule. RlPolicySimpleGalMibIpRulesEntry .1.3.6.1.4.1.89.56.9.7.1 |
rlPolicySimpleGalMibIpRulesPortTypeThe port type (interior/boundary) to which this rule applies.ro RlPolicySimpleGalMibPortType .1.3.6.1.4.1.89.56.9.7.1.1 |
rlPolicySimpleGalMibIpRulesIndexThis enumerates the table. The user should assign indices in such a
way that there will be a gap big enough between one rule and the next
to allow insertion of additional rules in between (a gap of 1000 is
recommended).ro INTEGER .1.3.6.1.4.1.89.56.9.7.1.2 |
rlPolicySimpleGalMibIpRulesDescriptionInformational text given by the user to describe the rule.rw DisplayString .1.3.6.1.4.1.89.56.9.7.1.3 |
rlPolicySimpleGalMibIpRulesTosOrDscpIndicates the TOS or DSCP to compare with.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.4 |
rlPolicySimpleGalMibIpRulesProtocolIndicates the L4 protocol to compare with.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.5 |
rlPolicySimpleGalMibIpRulesSrcIpIndicates the source IP address to compare with.rw IpAddress .1.3.6.1.4.1.89.56.9.7.1.6 |
rlPolicySimpleGalMibIpRulesSrcIpMaskIndicates the number of most significant bits of the Ip Address
that are used in specifying IP source addresses in classifiers.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.7 |
rlPolicySimpleGalMibIpRulesDstIpIndicates the destination IP address to compare with.rw IpAddress .1.3.6.1.4.1.89.56.9.7.1.8 |
rlPolicySimpleGalMibIpRulesDstIpMaskIndicates the number of most significant bits of the Ip Address
that are used in specifying IP destination addresses in classifiers.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.9 |
rlPolicySimpleGalMibIpRulesSrcPortIndicates the source L4 port to compare with.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.10 |
rlPolicySimpleGalMibIpRulesDstPortIndicates the destination L4 port to compare with.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.11 |
rlPolicySimpleGalMibIpRulesInIfIndexListIndicates the list of input ports to which this rule applies.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.7.1.12 |
rlPolicySimpleGalMibIpRulesConditionIndicate the relation that should hold for each relevant field of
the rule in comparison to the packet's field.rw Enumeration .1.3.6.1.4.1.89.56.9.7.1.13 |
rlPolicySimpleGalMibIpRulesActionIndicates the action to be performed if there is a match with the rule.rw Enumeration .1.3.6.1.4.1.89.56.9.7.1.14 |
rlPolicySimpleGalMibIpRulesProfilePointerIndicates the profile attached to the rule. The
value is the index in the profile table of the attached profile.
Value 0 means that no profile is attached to the rule and is valid only
in case of action block.rw INTEGER .1.3.6.1.4.1.89.56.9.7.1.15 |
rlPolicySimpleGalMibIpRulesOutIfIndexListIndicates the list of output ports to on which bandwidth should be
allocated for this rule.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.7.1.16 |
rlPolicySimpleGalMibIpRulesBitsUseda bit mask that indicates the the used fields for the entry:
(the implemention is identical to BITS implementation,from MSB to LSB)
|87654321|
8 - tosOrDscp
7 - Protocol
6 - SrcIp
5 - DstIp
4 - SrcIpPort
3 - DstIpPortrw OCTET STRING .1.3.6.1.4.1.89.56.9.7.1.17 |
rlPolicySimpleGalMibIpRulesErrorDescripA description error indicate the user about the specific error.
The error can cause by one of the following reasons:
1. if the profile was asign to the rule could not be perform
2. if the operation of QoS portLock failedro DisplayString .1.3.6.1.4.1.89.56.9.7.1.18 |
rlPolicySimpleGalMibIpRulesStatusThe status of a table entry.
It is used to delete an entry from this table.
notInService is used to disable an entry.
notReady will be assigned by the device to indicate that the rule
can not be active because some ports in the output ports list are not
in a state allowing bandwidth allocation guarantee.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.7.1.19 |
rlPolicySimpleGalMibIpxFcogTableThis table defines the used fields for ipx classification SEQUENCE OF RlPolicySimpleGalMibIpxFcogEntry .1.3.6.1.4.1.89.56.9.8 |
rlPolicySimpleGalMibIpxFcogEntrythe entry defines the used fields for classification RlPolicySimpleGalMibIpxFcogEntry .1.3.6.1.4.1.89.56.9.8.1 |
rlPolicySimpleGalMibIpxFcogIndexthe table index - only one entry existro INTEGER (1) .1.3.6.1.4.1.89.56.9.8.1.1 |
rlPolicySimpleGalMibIpxFcogDstNetIndicates the parts of the field in use in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.8.1.2 |
rlPolicySimpleGalMibIpxFcogDstNodeIndicates the parts of the field in use in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.8.1.3 |
rlPolicySimpleGalMibIpxFcogDstSocketIndicates whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.8.1.4 |
rlPolicySimpleGalMibIpxFcogSrcNetIndicates the parts of the field in use in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.8.1.5 |
rlPolicySimpleGalMibIpxFcogSrcNodeIndicates the parts of the field in use in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.8.1.6 |
rlPolicySimpleGalMibIpxFcogSrcSocketIndicates whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.8.1.7 |
rlPolicySimpleGalMibIpxFcogInIfIndexIndicates whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.8.1.8 |
rlPolicySimpleGalMibIpxRulesTableThis table contains the policy rules defined by the user. The order
of the entries in the table is important, since the first rule that
matches the incoming packet will be acted upon, ignoring any
further rules that may match as well. SEQUENCE OF RlPolicySimpleGalMibIpxRulesEntry .1.3.6.1.4.1.89.56.9.9 |
rlPolicySimpleGalMibIpxRulesEntryThis entry defines one policy rule. RlPolicySimpleGalMibIpxRulesEntry .1.3.6.1.4.1.89.56.9.9.1 |
rlPolicySimpleGalMibIpxRulesIndexThis enumerates the table. The user should assign indices in such a
way that there will be a gap big enough between one rule and the next
to allow insertion of additional rules in between (a gap of 1000 is
recommended).ro INTEGER .1.3.6.1.4.1.89.56.9.9.1.1 |
rlPolicySimpleGalMibIpxRulesDescriptionInformational text given by the user to describe the rule.rw DisplayString .1.3.6.1.4.1.89.56.9.9.1.2 |
rlPolicySimpleGalMibIpxRulesDstNetIndicate the ipxDst Net to compare torw OCTET STRING .1.3.6.1.4.1.89.56.9.9.1.3 |
rlPolicySimpleGalMibIpxRulesDstNodeIndicate the ipxDstNode to compare torw OCTET STRING .1.3.6.1.4.1.89.56.9.9.1.4 |
rlPolicySimpleGalMibIpxRulesDstSocketIndicate the ipx DstSocket to compare torw INTEGER .1.3.6.1.4.1.89.56.9.9.1.5 |
rlPolicySimpleGalMibIpxRulesSrcNetIndicate the ipxSrc Net to compare torw OCTET STRING .1.3.6.1.4.1.89.56.9.9.1.6 |
rlPolicySimpleGalMibIpxRulesSrcNodeIndicate the ipxSrcNode to compare torw OCTET STRING .1.3.6.1.4.1.89.56.9.9.1.7 |
rlPolicySimpleGalMibIpxRulesSrcSocketIndicate the ipx SrcSocket to compare torw INTEGER .1.3.6.1.4.1.89.56.9.9.1.8 |
rlPolicySimpleGalMibIpxRulesInIfIndexListIndicates the list of input ports to which this rule applies.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.9.1.9 |
rlPolicySimpleGalMibIpxRulesConditionIndicate the relation that should hold for each relevant field of
the rule in comparison to the packet's.rw Enumeration .1.3.6.1.4.1.89.56.9.9.1.10 |
rlPolicySimpleGalMibIpxRulesActionIndicates the action to be performed if the rule matches.rw Enumeration .1.3.6.1.4.1.89.56.9.9.1.11 |
rlPolicySimpleGalMibIpxRulesProfilePointerIndicates the profile attached to the rule. The
value is the index in the profile table of the attached profile.
Value 0 means that no profile is attached to the rule and is valid only
in case of action block.rw INTEGER .1.3.6.1.4.1.89.56.9.9.1.12 |
rlPolicySimpleGalMibIpxRulesOutIfIndexListIndicates the list of output ports on which bandwidth should be
allocated for this rule.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.9.1.13 |
rlPolicySimpleGalMibIpxRulesStatusThe status of a table entry.
It is used to delete an entry from this table.
notInService is used to disable an entry.
notReady will be assigned by the device to indicate that the rule
can not be active because some ports in the output ports list are not
in a state allowing bandwidth allocation guarantee.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.9.1.14 |
rlPolicySimpleGalMibBridgeFcogTableThe table defines the used fields for Bridge classification SEQUENCE OF RlPolicySimpleGalMibBridgeFcogEntry .1.3.6.1.4.1.89.56.9.10 |
rlPolicySimpleGalMibBridgeFcogEntrythe entry defines the used fields for classification RlPolicySimpleGalMibBridgeFcogEntry .1.3.6.1.4.1.89.56.9.10.1 |
rlPolicySimpleGalMibBridgeFcogIndexthe table index - only one entry existro INTEGER (1) .1.3.6.1.4.1.89.56.9.10.1.1 |
rlPolicySimpleGalMibBridgeFcogDstMacIndicate the use of the field in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.10.1.2 |
rlPolicySimpleGalMibBridgeFcogSrcMacIndicate the use of the field in the rulesrw OCTET STRING .1.3.6.1.4.1.89.56.9.10.1.3 |
rlPolicySimpleGalMibBridgeFcogVidIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.4 |
rlPolicySimpleGalMibBridgeFcogInIfIndexIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.5 |
rlPolicySimpleGalMibBridgeFcogEthTypeIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.6 |
rlPolicySimpleGalMibBridgeFcogIpTosOrDscpIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.7 |
rlPolicySimpleGalMibBridgeFcogIpProtocolIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.8 |
rlPolicySimpleGalMibBridgeFcogIpSrcIpMaskIndicate the number of used bits of the Ip Address from the leftrw INTEGER .1.3.6.1.4.1.89.56.9.10.1.9 |
rlPolicySimpleGalMibBridgeFcogIpDstIpMaskIndicate the number of used bits of the Ip Address from the leftrw INTEGER .1.3.6.1.4.1.89.56.9.10.1.10 |
rlPolicySimpleGalMibBridgeFcogIpSrcPortIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.11 |
rlPolicySimpleGalMibBridgeFcogIpDstPortIndicate whether the field is in use in the rulesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.10.1.12 |
rlPolicySimpleGalMibBridgeRulesTableThis table contains the policy rules defined by the user. The order
of the entries in the table is important, since the first rule that
applies to the incoming packet will be acted upon, ignoring any
further rules that may apply as well. SEQUENCE OF RlPolicySimpleGalMibBridgeRulesEntry .1.3.6.1.4.1.89.56.9.11 |
rlPolicySimpleGalMibBridgeRulesEntryThis entry defines one policy rule. RlPolicySimpleGalMibBridgeRulesEntry .1.3.6.1.4.1.89.56.9.11.1 |
rlPolicySimpleGalMibBridgeRulesIndexThis enumerates the table. The user should assign indices in such a
way that there will be a gap big enough between one rule and the next
to allow insertion of additional rules in between (a gap of 1000 is
recommended).ro INTEGER .1.3.6.1.4.1.89.56.9.11.1.1 |
rlPolicySimpleGalMibBridgeRulesDescriptionInformational text given by the user to describe the rule.rw DisplayString .1.3.6.1.4.1.89.56.9.11.1.2 |
rlPolicySimpleGalMibBridgeRulesDstMacIndicate the Dst mac to comparerw OCTET STRING .1.3.6.1.4.1.89.56.9.11.1.3 |
rlPolicySimpleGalMibBridgeRulesSrcMacIndicate the source mac to comparerw OCTET STRING .1.3.6.1.4.1.89.56.9.11.1.4 |
rlPolicySimpleGalMibBridgeRulesVidIndicate the vlanId to comparerw INTEGER .1.3.6.1.4.1.89.56.9.11.1.5 |
rlPolicySimpleGalMibBridgeRulesInIfIndexListIndicates the list of input ports to which this rule applies.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.11.1.6 |
rlPolicySimpleGalMibBridgeRulesEthTypeIndicate the Ethernet type of the packetrw INTEGER .1.3.6.1.4.1.89.56.9.11.1.7 |
rlPolicySimpleGalMibBridgeRulesIpTosOrDscpIndicates the tos or dscp to comparerw INTEGER .1.3.6.1.4.1.89.56.9.11.1.8 |
rlPolicySimpleGalMibBridgeRulesIpProtocolIndicates the protocol to comparerw INTEGER .1.3.6.1.4.1.89.56.9.11.1.9 |
rlPolicySimpleGalMibBridgeRulesIpSrcIpIndicate the srcIp to comparerw IpAddress .1.3.6.1.4.1.89.56.9.11.1.10 |
rlPolicySimpleGalMibBridgeRulesIpDstIpIndicate the DstIp to comparerw IpAddress .1.3.6.1.4.1.89.56.9.11.1.11 |
rlPolicySimpleGalMibBridgeRulesIpSrcPortIndicate the Src port to comparerw INTEGER .1.3.6.1.4.1.89.56.9.11.1.12 |
rlPolicySimpleGalMibBridgeRulesIpDstPortIndicate the Src port to comparerw INTEGER .1.3.6.1.4.1.89.56.9.11.1.13 |
rlPolicySimpleGalMibBridgeRulesConditionIndicate the relation that should hold for each relevant field of
the rule in comparison to the packet's field.rw Enumeration .1.3.6.1.4.1.89.56.9.11.1.14 |
rlPolicySimpleGalMibBridgeRulesActionIndicates the action to be performed if there is a match with the rule.rw Enumeration .1.3.6.1.4.1.89.56.9.11.1.15 |
rlPolicySimpleGalMibBridgeRulesProfilePointerIndicates the profile attached to the rule. The
value is the index in the profile table of the attached profile.
Value 0 means that no profile is attached to the rule and is valid only
in case of action block.rw INTEGER .1.3.6.1.4.1.89.56.9.11.1.16 |
rlPolicySimpleGalMibBridgeRulesOutIfIndexListIndicates the list of output ports to on which bandwidth should be
allocated for this rule.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.56.9.11.1.17 |
rlPolicySimpleGalMibBridgeRulesStatusThe status of a table entry.
It is used to delete an entry from this table.
notInService is used to disable an entry.
notReady will be assigned by the device to indicate that the rule
can not be active because some ports in the output ports list are not
in a state allowing bandwidth allocation guarantee.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.56.9.11.1.18 |
rlPolicySimpleGalMibPortTableThe table defines all of the ports types SEQUENCE OF RlPolicySimpleGalMibPortEntry .1.3.6.1.4.1.89.56.9.12 |
rlPolicySimpleGalMibPortEntryAn entry defines a port's type RlPolicySimpleGalMibPortEntry .1.3.6.1.4.1.89.56.9.12.1 |
rlPolicySimpleGalMibPortIfIndexThis enumerates the table entry.ro INTEGER .1.3.6.1.4.1.89.56.9.12.1.1 |
rlPolicySimpleGalMibPortTypeDefines the port typerw RlPolicySimpleGalMibPortType .1.3.6.1.4.1.89.56.9.12.1.2 |
rlGalPolicyModeIndicates whether the QoS is for:
-All Bridged packets; or
-All routed IP packets.
The value cannot change after system initro Enumeration .1.3.6.1.4.1.89.56.10 |