ESM-snmp
Detailed view of the defined objects, syntax rules, and hierarchical paths.
398
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
398 total| Object Name |
|---|
private OBJECT IDENTIFIER .1.3.6.1.4 |
SNMPv2-PARTY-MIB Unknown .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
fibronics OBJECT IDENTIFIER .1.3.6.1.4.1.22 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.22.3 |
traprun OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.1 |
rTrapAddrTableTable of managers to which traps
must be sent. Up to 10
entries in table SEQUENCE OF RTrapAddrEntry .1.3.6.1.4.1.22.3.1.1 |
rTrapAddrEntry RTrapAddrEntry .1.3.6.1.4.1.22.3.1.1.1 |
rTrapAddrAddrIP address of entity
requesting event notificationrw IpAddress .1.3.6.1.4.1.22.3.1.1.1.1 |
rTrapAddrCommCommunity name the receiving
entity will expect.
When reading the instance of this
object the value has no meaning.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.3.1.1.1.2 |
rTrapAddrVerVersion number supported by
destination noderw INTEGER .1.3.6.1.4.1.22.3.1.1.1.3 |
rTrapAddrTypeType of event that should be
reported to this address,
bit 0 - authentication trap
bit 1 - other SNMP traps
bit 2 - Error Traps
bit 3 - Diagnostic Traps
bit 4 - Debug Traps
bit 5 - Enterprise Traps other than fmDiagGenericTraprw OCTET STRING .1.3.6.1.4.1.22.3.1.1.1.4 |
rTrapAddrStateDetermines status of this entryrw Enumeration .1.3.6.1.4.1.22.3.1.1.1.5 |
rTrapAddrFlagIf the entry is fixed, it can not
be deleted because of agingrw Enumeration .1.3.6.1.4.1.22.3.1.1.1.6 |
rTrapAddrAgeAging time of the entry (in sec)ro INTEGER .1.3.6.1.4.1.22.3.1.1.1.7 |
rTrapLearningLearn the addresses of the managers
automatically.ro Enumeration .1.3.6.1.4.1.22.3.1.2 |
rTrapAgingTime in sec. until we erase a trap
entryro INTEGER .1.3.6.1.4.1.22.3.1.3 |
traperm OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.2 |
pTrapAddrTableTable of managers to which traps
must be sent. Up to 10
entries in table SEQUENCE OF PTrapAddrEntry .1.3.6.1.4.1.22.3.2.1 |
pTrapAddrEntry PTrapAddrEntry .1.3.6.1.4.1.22.3.2.1.1 |
pTrapAddrAddrIP address of entity
requesting event notificationrw IpAddress .1.3.6.1.4.1.22.3.2.1.1.1 |
pTrapAddrCommCommunity name the receiving
entity will expect.
When reading the instance of this
object the value has no meaning.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.3.2.1.1.2 |
pTrapAddrVerVersion number supported by
destination noderw INTEGER .1.3.6.1.4.1.22.3.2.1.1.3 |
pTrapAddrTypeType of event that should be
reported to this address,
bit 0 - authentication trap
bit 1 - other SNMP traps
bit 2 - Error Traps
bit 3 - Diagnostic Traps
bit 4 - Debug Traps
bit 5 - all Enterprise Traps other than fmDiagGenericTraprw OCTET STRING .1.3.6.1.4.1.22.3.2.1.1.4 |
pTrapAddrStateDetermines status of this entryrw Enumeration .1.3.6.1.4.1.22.3.2.1.1.5 |
pTrapLearningLearn the addresses of the managers
automatically.rw Enumeration .1.3.6.1.4.1.22.3.2.2 |
pTrapAgingTime in sec. until we erase a trap
entryrw INTEGER .1.3.6.1.4.1.22.3.2.3 |
trapvar OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.3 |
fm800 OBJECT IDENTIFIER .1.3.6.1.4.1.22.51 |
fmsystem OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1 |
fmsystemrun OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1.1 |
fmSystemResetResetting the CARD.
When reading the instance of this
object the value has no meaning.
cold reset is performed with selftest ,
while warm start is performed without
selftestrw Enumeration .1.3.6.1.4.1.22.51.1.1.4 |
fmSystemSelfTestLevelType of self test to be
executed upon cold-resetrw Enumeration .1.3.6.1.4.1.22.51.1.1.5 |
fmSystemVersionVersion of the station. The version includes
station type, hardware version and software version.
The string can include CR and LFro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.1.1.6 |
fmSystemIpAddrIP address of the agentro IpAddress .1.3.6.1.4.1.22.51.1.1.7 |
fmSystemIPNetMaskIP Network Maskro IpAddress .1.3.6.1.4.1.22.51.1.1.8 |
fmSystemIPDefGwayDefault Gateway Addressro IpAddress .1.3.6.1.4.1.22.51.1.1.9 |
fmSystemFileServerIP address to which a TFTP for boot is sent.rw IpAddress .1.3.6.1.4.1.22.51.1.1.10 |
fmSystemBootFilePath and file name that is
sent as a TFTP requestro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.1.1.11 |
fmSystemBootModeMethod for bootingrodeprecated Enumeration .1.3.6.1.4.1.22.51.1.1.12 |
fmSystemDownLoadDownloading the ESM.
When reading the instance of this
object the value has no meaning.rw Enumeration .1.3.6.1.4.1.22.51.1.1.13 |
fmSystemSlipIpAddrSLIP IP address.
This is object is available
only when slip interface existro IpAddress .1.3.6.1.4.1.22.51.1.1.14 |
fmSystemSlipIPNetMaskSLIP IP Network Mask
This is object is available
only when slip interface existro IpAddress .1.3.6.1.4.1.22.51.1.1.15 |
fmSystemSlipBaudRateSLIP Baud rate
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.16 |
fmSystemSlipParitySLIP Parity
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.17 |
fmSystemSlipStopBitsSLIP Stop Bits
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.18 |
fmsystemperm OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1.2 |
pfmSystemIpAddrIP address of the agentrw IpAddress .1.3.6.1.4.1.22.51.1.2.7 |
pfmSystemIPNetMaskIP Network Maskrw IpAddress .1.3.6.1.4.1.22.51.1.2.8 |
pfmSystemIPDefGwayDefault Gateway Addressrw IpAddress .1.3.6.1.4.1.22.51.1.2.9 |
pfmSystemFileServerIP address to which a TFTP for boot is sent.rw IpAddress .1.3.6.1.4.1.22.51.1.2.10 |
pfmSystemBootFilePath and file name that is
sent as a TFTP requestrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.1.2.11 |
pfmSystemBootModeMethod for bootingrw Enumeration .1.3.6.1.4.1.22.51.1.2.12 |
pfmSystemReadCommunityCommunity string for reading
When reading the instance of this
object the value has no meaning.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.1.2.13 |
pfmSystemWriteCommunityCommunity string for writing
When reading the instance of this
object the value has no meaning.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.1.2.14 |
pfmSystemSlipIpAddrSLIP IP address
This is object is available
only when slip interface existrw IpAddress .1.3.6.1.4.1.22.51.1.2.15 |
pfmSystemSlipIPNetMaskSLIP IP Network Mask
This is object is available
only when slip interface existrw IpAddress .1.3.6.1.4.1.22.51.1.2.16 |
pfmSystemSlipBaudRateSLIP Baud rate
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.17 |
pfmSystemSlipParitySLIP Parity
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.18 |
pfmSystemSlipStopBitsSLIP Stop Bits
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.19 |
fmslot OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.2 |
fmSlotMasterClearUpon writing, performs a master
clear command on all the slots.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.1 |
fmSlotTable SEQUENCE OF FmSlotEntry .1.3.6.1.4.1.22.51.2.2 |
fmSlotEntry FmSlotEntry .1.3.6.1.4.1.22.51.2.2.1 |
fmSlotIndexSlot Numberro INTEGER .1.3.6.1.4.1.22.51.2.2.1.1 |
fmSlotIDID of the card in the slot.
Special , not-exist, ID identifies
a GigaHUB slot that doesn't exist:
slot 5, if a HALF MultiHUB installed, or
slot 9, if a FULL MultiHUB installed.rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.2 |
fmSlotDescrAscii string. Description
of the cardro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.2.2.1.3 |
fmSlotInfoUser general info for the slot.
Can be the use of that slot, its
location etc...rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.2.2.1.4 |
fmSlotStatusStatus bits of the card in the slot, organized
by card channel. Each channel's status occupies
2 bytes. For more information about
the meaning of the status, read the
specific user manual of each card.ro OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.5 |
fmSlotPrevStatusPrevious status bits of the card in the slot,
organized by card channel. Each channel's status
occupies 2 bytes. For more information about
the meaning of the status, read the
specific user manual of each card.
This object id is used
mainly for traps (see Card Trap).ro OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.6 |
fmSlotRLBSetArgument: 1 - 4. Perform a
RLB set operation on the
channel passed as argument.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.7 |
fmSlotRLBClearArgument: 1 - 4. Perform a
RLB clear operation on the
channel passed as argument.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.8 |
fmSlotExpCodePerform an expanded command
on the slot. For expanded codes,
see specific card user manual.
When reading the instance of this
object the value has no meaning.
Extended command codes for NDS cards
1. CC892.303 (Ethernet)
Code (Dec/Hex) Command
02/02 Detach Port 13
03/03 Attach Port 13
04/04 Detach Port 01
05/05 Attach Port 01
06/06 Detach Port 02
07/07 Attach Port 02
08/08 Detach Port 03
09/09 Attach Port 03
10/0A Detach Port 04
11/0B Attach Port 04
12/0C Detach Port 05
13/0D Attach Port 05
14/0E Detach Port 06
15/0F Attach Port 06
16/10 Detach Port 07
17/11 Attach Port 07
18/12 Detach Port 08
19/13 Attach Port 08
20/14 Detach Port 09
21/15 Attach Port 09
22/16 Detach Port 10
23/17 Attach Port 10
24/18 Detach Port 11
25/19 Attach Port 11
26/1A Detach Port 12
27/1B Attach Port 12
28/1C Detach All Ports
29/1D Attach All Ports
30/1E Reset Card
31/1F Link Select
======================================================
2. CC892.308 (Ethernet)
Code (Dec/Hex) Command
02/02 Detach Port 01
03/03 Attach Port 01
04/04 Detach Port 02
05/05 Attach Port 02
06/06 Detach Port 03
07/07 Attach Port 03
08/08 Detach Port 04
09/09 Attach Port 04
10/0A Detach Port 05
11/0B Attach Port 05
12/0C Detach Port 06
13/0D Attach Port 06
14/0E Detach Port 07
15/0F Attach Port 07
16/10 Detach Port 08
17/11 Attach Port 08
...
28/1C Detach All Ports
29/1D Attach All Ports
30/1E Reset Card
31/1F Link Select
================================================
3. CC892.322 (Token-ring)
Module 323
Code (Dec/Hex) Command
02/02 Detach Port 01
03/03 Attach Port 01
04/04 Detach Port 02
05/05 Attach Port 02
06/06 Detach Port 03
07/07 Attach Port 03
08/08 Detach Port 04
09/09 Attach Port 04
10/0A Detach Port 05
11/0B Attach Port 05
12/0C Detach Port 06
13/0D Attach Port 06
18/12 Detach Port 07
19/13 Attach Port 07
20/14 Detach Port 08
21/15 Attach Port 08
22/16 Detach Port 19
23/17 Attach Port 19
24/18 Detach Port 10
25/19 Attach Port 10
26/1A Detach Port 11
27/1B Attach Port 11
28/1C Detach Port 12
29/1D Attach Port 12
30/1E Reset Card
34/22 Detach Port 13
35/23 Attach Port 13
36/24 Detach Port 14
37/25 Attach Port 14
38/26 Detach Port 15
39/27 Attach Port 15
40/28 Detach Port 16
41/29 Attach Port 16
42/2A Detach Port 17
43/2B Attach Port 17
44/2C Detach Port 18
45/2D Attach Port 18
50/32 Detach Port 19
51/33 Attach Port 19
52/34 Detach Port 20
53/35 Attach Port 20
54/36 Detach Port 21
55/37 Attach Port 21
56/38 Detach Port 22
57/39 Attach Port 22
58/3A Detach Port 23
59/3B Attach Port 23
60/3C Detach Port 24
61/3D Attach Port 24
77/4D Detach All Ports
79/4F Attach All Ports
========================================================
Module 325
30/1E Reset Card
80/50 Detach Local Port 1 (channel 1)
81/51 Attach Local Port 1 (channel 1)
82/52 Detach Local Port 2 (channel 1)
83/53 Attach Local Port 2 (channel 1)
88/58 Detach Local Port 1 (channel 3)
89/59 Attach Local Port 1 (channel 3)
90/5A Detach Local Port 2 (channel 3)
91/5B Attach Local Port 2 (channel 3)
77/4D Detach All Ports
79/4F Attach All Ports
4. CC892.427 (Voice)
Code (Dec/Hex) Command
04/04 Loopback OFF on Port 1
05/05 Loopback ON on Port 1
06/06 Loopback OFF on Port 2
07/07 Loopback ON on Port 2
08/08 Loopback OFF on Port 3
09/09 Loopback ON on Port 3
10/0A Loopback OFF on Port 4
11/0B Loopback ON on Port 4
12/0C Loopback OFF on Port 5
13/0D Loopback ON on Port 5
14/0E Loopback OFF on Port 6
15/0F Loopback ON on Port 6
16/10 Loopback OFF on Port 7
17/11 Loopback ON on Port 7
18/12 Loopback OFF on Port 8
19/13 Loopback ON on Port 8
20/14 Loopback OFF on Port 9
21/15 Loopback ON on Port 9
22/16 Loopback OFF on Port 10
23/17 Loopback ON on Port 10
24/18 Loopback OFF on Port 11
25/19 Loopback ON on Port 11
26/1A Loopback OFF on Port 12
27/1B Loopback ON on Port 12
28/1C Loopback OFF on Port 13
29/1D Loopback ON on Port 13
30/1E Loopback OFF on Port 14
31/1F Loopback ON on Port 14
32/20 Loopback OFF on Port 15
33/21 Loopback ON on Port 15
34/22 Loopback OFF on Port 16
35/23 Loopback ON on Port 16
37/25 Loopback ALL on Ports 1-8
39/27 Loopback ALL on Ports 9-16
40/28 Alternate Mode on Channel Module #1
41/29 Normal Mode on Channel Module #1
42/2A Alternate Mode on Channel Module #2
43/2B Normal Mode on Channel Module #2
45/2D Configuration Load Module #1
47/2F Configuration Load Module #2
======================================================rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.9 |
fmSlotTrapMaskWhen the value is 1, no more traps
from that slot are sent, until next reset.
(temporary mask)rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.10 |
pfmSlotTrapMaskWhen the value is 1, no more traps for that slot
will be sent, starting after next reset (permanent mask)rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.11 |
fmSlotIpAddrIP address of a channel card.ro IpAddress .1.3.6.1.4.1.22.51.2.2.1.12 |
fmSlotMngAccessThis run-time object determines through which interface the
SNMP management will be permitted. The default is
through the managment bus, via the ESM. This object value is
reinitialized to its permanent value after system reset.
Setting the object is permitted only for slots containing
active SNMP managers. Such cards will change management access
immediately according to the specified value. Set values must
be either Management-Bus or LAN and the target slot must
contain an active SNMP agent.rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.13 |
pfmSlotMngAccessThis permanent object determines through which interface the
SNMP management will be permitted. The default is through the
managment bus, via the ESM.
This object has no effect on slots not containing SNMP agents.
The run-time object will receive this value after system reset
only if the value is permitted.
Setting the object is permitted only for slots containing
active SNMP managers. Such cards will change management access
only the next time the card is initialized. Set values must
be either Management-Bus or LAN and the target slot must
contain an active SNMP agent.rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.14 |
fmSlotEntityIndexThis object determines the Entity index which the card
is a memeber in.ro INTEGER .1.3.6.1.4.1.22.51.2.2.1.15 |
fmSlotCommunityThis object determines the Entity Community which the card
is a memeber in.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.2.2.1.16 |
fmSlotEntityManagerThis object determines if the card is an SNMP-manageable
Entity Manager.ro Enumeration .1.3.6.1.4.1.22.51.2.2.1.17 |
fmlu OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.3 |
fmLUIDLogic unit IDrw Enumeration .1.3.6.1.4.1.22.51.3.1 |
fmLUDescrAscii string. Description
of the logic unitro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.3.2 |
fmLUStatusOne byte of LU statusro OCTET STRING .1.3.6.1.4.1.22.51.3.3 |
fmLULinkSelectSetup LU link.rw Enumeration .1.3.6.1.4.1.22.51.3.4 |
fmLULoopBackSetUpon writing, performs LLB command.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.3.5 |
fmLULoopBackClrUpon writing, clear LLB command.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.3.6 |
fmLUTrapMaskWhen the value is 1, no more traps
from the LU are sent, until next reset.
(temporary mask)rw Enumeration .1.3.6.1.4.1.22.51.3.7 |
pfmLUTrapMaskWhen the value is 1, no more traps for the LU
will be sent, starting after next reset (permanent mask)rw Enumeration .1.3.6.1.4.1.22.51.3.8 |
fmdiag OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.5 |
fmDiagConfigVersion of the station. The version includes
station type, hardware version and software version.
The string can include CR and LFro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.51.5.1 |
fmDiagTrapInfoUsed for generic traps. The first word
is the trap code. The rest of the string is
the extra information. Contains CR and LF char.ro DisplayString .1.3.6.1.4.1.22.51.5.2 |
fmDiagFaultTableTable of fault reports from the agent SEQUENCE OF FmDiagFaultEntry .1.3.6.1.4.1.22.51.5.3 |
fmDiagFaultEntry FmDiagFaultEntry .1.3.6.1.4.1.22.51.5.3.1 |
fmDiagFaultIndexThe fault index in the
fault tablero INTEGER .1.3.6.1.4.1.22.51.5.3.1.1 |
fmDiagFaultReportGet the faults detected by the agentro DisplayString .1.3.6.1.4.1.22.51.5.3.1.2 |
fmDiagDebugThis object is for factory use only. Users must not
write into this variable or improper operation
can occur.rw Enumeration .1.3.6.1.4.1.22.51.5.4 |
fmrptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.11 |
lc308-129 OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.11.1 |
lc303-129 OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.11.3 |
lc312-129 OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.11.5 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.22.100 |
eth-rptrs OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1 |
xmh-rptrs OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1 |
lc342-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1.1 |
lc348-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1.2 |
nm349-sm OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1.3 |
lc343-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1.4 |
lc344-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.1.5 |
cc303 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.3 |
cc308 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.4 |
lc303 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.5 |
lc308 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.6 |
lc312 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.1.7 |
tr-concentrators OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.2 |
lc322 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.2.1 |
fddi-concentrators OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.3 |
brouters OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.4 |
terminal-servers OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.5 |
chassis OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6 |
gigaHUB OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1 |
fmLUOutOfSyncIssued when the Logic unit goes
out of synchronization TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.7 |
fmLUReturnToSyncIssues as soon as the logic unit
returns to synchronization TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.8 |
fmLUPassToMainIssues as soon as the logic unit
pass to main link TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.9 |
fmLUPassToSecondIssues as soon as the logic unit
pass to second link TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.10 |
fmLUPrimaryLinkFailWhen primary link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.11 |
fmLUPrimaryLinkOKWhen primary link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.12 |
fmLUSecondLinkFailWhen second link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.13 |
fmLUSecondLinkOKWhen second link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.14 |
fmLULLBOnWhen the logic unit enters LLB mode TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.15 |
fmLULLBOffWhen the logic unit exits LLB mode TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.16 |
fmLUChangeConfigIssues when a change in the LU configuration
is done TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.20 |
fmSlotTrapGenerated when a significant status has
changed in a slot. By xoring the 2 statuses,
the NMS can identify the cause of the trap. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.25 |
fmSlotChangeConfigIssued when the system detects
changes in its slots configuration TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.26 |
fmDiagGenericTrapGeneric Trap information TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.30 |
gigaPowerSupplyTrapThis trap message is generated as soon
as one of the power supply has changed its
operational status. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.31 |
gigaSensorTrapThis trap message is generated when there
is a change in enviromental sensor status. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.32 |
gigaHostAuthTrapThis trap is generated when an unauthorized host
attempts to perform an SNMP SET operation. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.33 |
gigaModuleTrapThis trap message is generated when there
is a change in module operational status TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.34 |
gigaModuleEmptyTrapThis trap is generated when a module is removed
from a modular slot. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.35 |
gigaModuleNotEmptyTrapThis trap is generated when a module is inserted
in a modular slot. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.36 |
gigaPhyResAttachChangeTrapThis trap is generated when physical module resource is
changed it's segment/ring attachment. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.37 |
gigaPhyResConfigChangeTrapThis trap is generated when there is a global change in
physical module resources configuration. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.38 |
gigaEbmTrapThis trap message is generated as soon
as one of the EBM cards has changed its
operational status. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.39 |
fmSlotIPAddressChangeThis trap is generated when IP Address
is changed in a slot. TRAP-TYPE .1.3.6.1.4.1.22.100.6.1.0.40 |
gigaLocationTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.1 |
gigaEsmBay OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.1.1 |
gigaModuleTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.2 |
gigaEsm OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.2.1 |
gigaPowerSupply OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.2.2 |
midiGigaHUB OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.6.1.3 |
mux OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7 |
cc010 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.1 |
cc012 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.2 |
cc020 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.3 |
cc031 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.4 |
cc032 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.5 |
cc041 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.6 |
cc042 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.7 |
cc044 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.8 |
cc832 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.9 |
cc201 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.10 |
cc202 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.11 |
cc214 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.12 |
cc321 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.13 |
cc301 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.14 |
cc233 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.15 |
cc260 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.16 |
sw11X OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.17 |
cc432 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.18 |
cc420 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.19 |
cc421 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.20 |
cc422 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.21 |
cc401 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.22 |
cc24X OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.23 |
cc427 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.24 |
cc211 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.25 |
cc212 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.26 |
cc010-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.27 |
cc012-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.28 |
cc020-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.29 |
cc041-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.30 |
cc042-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.31 |
cc044-ID OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.32 |
cc046A OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.33 |
cc046B OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.34 |
not-exist OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.7.100 |
atm-switch OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.8 |
xm504-card OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.8.1 |
eth-switch OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.9 |
xm512-card OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.9.1 |
xm514-card OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.9.2 |
xm516-card OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.9.3 |
tr-hubs OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10 |
tr-rptrs OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2 |
lc366-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.1 |
lc366p-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.1.1 |
lc362-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.2 |
lc362p-rptr OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.2.2 |
nm369-sm OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.3 |
em364-trnk OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.4 |
em364p-trnk OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.4.1 |
em365-trnk OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.10.2.5 |
bridges OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.11 |
eth2fddi OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.11.1 |
fx8616 OBJECT IDENTIFIER .1.3.6.1.4.1.22.100.11.1.1 |
mibs OBJECT IDENTIFIER .1.3.6.1.4.1.22.101 |
systems OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.1 |
mibsstack-rptrs OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.2 |
mibstr-hubs OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.3 |
mibsfddi-concentrators OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.4 |
mibsbrouters OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.5 |
chassis-mibs OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6 |
gigaHUBMib OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1 |
gigaHUBPrivate OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.1 |
gigaPhyResourceTableThis table maps resources to backplane segments/ring numbers SEQUENCE OF GigaPhyResourceEntry .1.3.6.1.4.1.22.101.6.1.1.1 |
gigaPhyResourceEntryThis table maps resources to backplane segments/ring numbers GigaPhyResourceEntry .1.3.6.1.4.1.22.101.6.1.1.1.1 |
gigaPhyResLocationTypeA unique integer representing the location type indexro INTEGER .1.3.6.1.4.1.22.101.6.1.1.1.1.1 |
gigaPhyResLocationA unique integer representing the location type instancero INTEGER .1.3.6.1.4.1.22.101.6.1.1.1.1.2 |
gigaPhyResIndexA unique integer representing the resource instance at this
locationro INTEGER .1.3.6.1.4.1.22.101.6.1.1.1.1.3 |
gigaPhyResTypeThe type of resource.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.1.1.1.4 |
gigaPhyResCapabilityA unique integer representing the resource capability for
attachment to the serial busses.ro Enumeration .1.3.6.1.4.1.22.101.6.1.1.1.1.5 |
gigaPhyResSegRingA unique integer representing the ring or segment number in
which the resource is attached to.rw INTEGER .1.3.6.1.4.1.22.101.6.1.1.1.1.6 |
gigaEbmTableA list of EBM cards entries, one for each
EBM card in the chassis. SEQUENCE OF GigaEbmEntry .1.3.6.1.4.1.22.101.6.1.1.2 |
gigaEbmEntryValues for a EBM card. GigaEbmEntry .1.3.6.1.4.1.22.101.6.1.1.2.1 |
gigaEbmIndexAn index value that uniquely identifies a
EBM cardro INTEGER .1.3.6.1.4.1.22.101.6.1.1.2.1.1 |
gigaEbmDescrA textual description of the EBM card.ro DisplayString .1.3.6.1.4.1.22.101.6.1.1.2.1.2 |
gigaEbmOperStatusActual status of the EBM card:
- unknown(1) - don't have the information
- empty(2) - no EBM card installed in slot
- bad(3) - unable to work due to failure
- good(4) - the card is good
- active(5) - the card is good and activero Enumeration .1.3.6.1.4.1.22.101.6.1.1.2.1.3 |
gigaHUBChassis OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2 |
chasInfo OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.1 |
chasTypeAn authoritative identification of the type of
hub-based or standalone chassis. By convention
this value is allocated within the SMI enterprises
subtree(1.3.6.1.4.1), and provides an easy and
unambiguous means for determining `what kind of
box' is being managed. If this information is not
present or unknown, its value should be set to the
value: chasTypeUnknown.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.1.1 |
chasPhysicalChangesThe number of physical changes that have occurred
in the chassis since the agent was warm/cold
started. This includes additions and removal of
modules and entities. Other uses are
implementation specific.ro Counter .1.3.6.1.4.1.22.101.6.1.2.1.2 |
chasChassisSerialNumberThe serial number of the chassis. If no serial
number is available then this object should be the
zero length string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.1.3 |
chasMultiConfWhich type of MultiHUB is installed in the chassis.ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.1.4 |
chasPhysical OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.2 |
chasPhyLocationTableThis table summarises the different classes of
and types of modular physical locations in the
chassis. This includes but is not limited to slot
within a chassis, power supply bay. SEQUENCE OF ChasPhyLocationEntry .1.3.6.1.4.1.22.101.6.1.2.2.1 |
chasPhyLocationEntryAn entry in the phyLocationTable ChasPhyLocationEntry .1.3.6.1.4.1.22.101.6.1.2.2.1.1 |
chasPhyLocationTypeIndexThis uniquely identifies the physical location
type within the chassis.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.2.1.1.1 |
chasPhyLocationCountThis defines the number of physical locations of
this type exist within the chassis.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.2.1.1.2 |
chasPhyLocationTypeUniquely identifies the 'type' of the physical
location within the chassis.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.2.1.1.3 |
chasPhyLocationDescrEach type of physical location within the chassis
is given a textual name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.22.101.6.1.2.2.1.1.4 |
chasPhyModuleTableThis table defines the physical modules within a
chassis. This is done by defining the type
physical modules and the physical location where
it resides. This table also provides a mapping
between physical modules and their location
within the chassis. SEQUENCE OF ChasPhyModuleEntry .1.3.6.1.4.1.22.101.6.1.2.2.2 |
chasPhyModuleEntryAn entry in this table that describes a physical
module that resides at a given physcial location
within the chassis. ChasPhyModuleEntry .1.3.6.1.4.1.22.101.6.1.2.2.2.1 |
chasPhyModuleLocationTypeAn instance of a module is identified by the
physical location in which it resides. The physical
location is identified by location type index and
location index (instance of that location type).
This object defines an instance of the
chasPhyLocationType.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.2.2.1.1 |
chasPhyModuleLocationAn instance of a module is identified by the
physical location which it resides. The physical
location is identified by location type index and
location index (instance of that location type).
This object defines the instance of a particular
location type. It must be within the bounds
defined by chasPhyLocationCount.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.2.2.1.2 |
chasPhyModuleTypeAn authoritative identification of the type of
physcial module in this physical location. A
value of chasModuleUnknown indicates that the
type of physical module is unknown.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.2.2.1.3 |
chasPhyModuleSwVersionA textual description of the version/revision
level for this module's software. If not realized
this value should be set to the zero-length
string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.2.2.1.4 |
chasPhyModuleHwVersionA textual description of the version/revision
level for this module's firmware. If not realized
this value should be set to the zero-length
string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.2.2.1.5 |
chasPhyModuleSerialNumberThe serial number of the physical module present
in this physical location. If the physical
location table is implemented as dense and the
slot is empty this value will be the zero length
string. If no serial number is available for a
physical module this value should set to a zero
length string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.2.2.1.6 |
chasPhyModuleDescriptionA textual description of the physical module
plugged that resides in this physical location.
If not available this value should be set to a
zero length string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.2.2.1.7 |
chasPhyModuleLastChangeTimeThe value of MIB-II's sysUpTime (in the agent
supporting this chassis MIB) at which a module was
last inserted or initialized. If the module has
not changed since the last network managment
system reinitialized then this object has a zero
value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.22.101.6.1.2.2.2.1.8 |
chasPhyModuleAdminStatusProvides desired state of the given physical
module. Notice that not all values may be
supported by the specified physical module. In
this case and SNMP error will be returned when the
set is attempted.
A physical module maybe activated by writing a
value of enable(2).
A physical module may be de-activated by writing
a value of disable(3). In a disabled state a
physical module is present in the chassis but is
benign.
Writing a value of sw-reset(4) initiates a
software reset sequence.
Writing a value of hw-reset(7) initiates a
hardware reset sequence.
A value of programLoad(5) initiates a software
load sequence.
Writing a value of test(6) should start a self
test sequence within the physical module.rw Enumeration .1.3.6.1.4.1.22.101.6.1.2.2.2.1.9 |
chasPhyModuleOperStatusProvides operational status of the module. The
following are possible definitions of the values.
The exact definition of the values is
implementation specific. A value of other(1)
implies some undetermined state, possibly as a
result of setting phyAdminStatus to a value of
disable(3). A value of invalid(2) could have the
possible meaning that the module exists but the
chassis manager has no direct control over the
module. A value of testing(3) may be a diagnostic
state. A value of operational(4) implies that the
entity is running with no errors or warnings.
State resetInProgress(5) implies equivalent of
setting phyAdminStatus to reset(4). The states of
warning(6), nonFatalError(7), fatalError(8)
reflect conditions detected during operation. The
entity may or may not be still functional.
For example if a modules value of phyAdminStatus
is disable(3) and is set to enable(2) then
phyOperStatus may enter a state of testing(3) then
change to a value of operational(4).ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.2.2.1.10 |
chasEntity OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.3 |
chasEntityTableA table that contains information about the
'logical' networking devices (entities) in this
chassis. SEQUENCE OF ChasEntityEntry .1.3.6.1.4.1.22.101.6.1.2.3.1 |
chasEntityEntryInformation concerning an entity in the chassis.
Conceptual rows may not be created or deleted with
SNMP operations. ChasEntityEntry .1.3.6.1.4.1.22.101.6.1.2.3.1.1 |
chasEntityIndexA unique index for the entity for which this
entry contains information.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.3.1.1.1 |
chasEntityObjectIDThe specific type of entity. The value of this
object is analagous to MIB-II's sysObjectId. In
particular, it has the same value as would be
returned if the SNMP Party (identified by
chasEntityParty) and/or the community (identified
by chasIpAddress and chasCommunity), were queried
for sysObjectId.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.3.1.1.2 |
chasEntityDescrA textual description of the entity. The value
of this object is analagous to MIB-II's sysDescr.
In particular, it has the same value as would be
returned if the SNMP Party (identified by
chasEntityParty) and/or the community (identified
by chasIpAddress and chasCommunity), were queried
for sysDescr.rw DisplayString .1.3.6.1.4.1.22.101.6.1.2.3.1.1.3 |
chasEntityAdminStatusProvides the administratively desired state of
the given entity.
An entity is activated by writing a value of
enable(2).
An entity may be de-activated by writing a value
of disable(3). In a disabled state, a entity does
exist within the given chassis, but is benign. A
disabled entity is available for subsequent
activation.
Writing a value of reset(4) specifies an entity
should initiate a reset sequence.
Writing a value of programload(5) specifies an
entity should initiate a program load sequence.
Writing a value of test(6) specifies an entity
should initiate a testing sequence.
Agent support of the writing of any of the values
of this object is implementation-specific. For
example, this object might be read only for
entities that disabling would compromise the
integrity of the chassis.rw Enumeration .1.3.6.1.4.1.22.101.6.1.2.3.1.1.4 |
chasEntityOperStatusProvides operational status of the entity. The
following are possible definitions of the values.
The exact definition of the values is
implementation specific. A value of other(1)
implies some undetermined state, possibly as a
result of setting chasEntityAdminStatus to a value
of disable(3). A value of invalid(2) could have
the possible meaning that the entity exists but
the chassis manager has no direct control of the
entity. A value of testing(3) may be a diagnostic
state. A value of operational(4) implies that the
entity is running with no errors or warnings.
State resetInProgress(5) implies equivalent of
setting chasEntityAdminStatus to reset(4). The
states of warning(6), nonFatalError(7),
fatalError(8) reflect conditions detected during
operation. The entity may or may not be still
functional. State loading(10) is a result of
asserting programload(5) in chasEntityAdminStatus.
For example if an entities value of
chasEntityAdminStatus is disable(3) and is set to
enable(2) then chasEntityOperStatus may enter a
state of testing(3) then change to a value of
operational(4).ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.3.1.1.5 |
chasEntityTimeStampThe value of MIB-II's sysUpTime (in the agent
supporting this MIB) at which this entity was last
(re-)initialized. If the entity has not been
initialized then this object has a zero value.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.22.101.6.1.2.3.1.1.6 |
chasEntityPartyThe SNMP Party which provides access to the
detailed management information for this entity.
Note that the definition of a SNMP Party includes
the location at which it executes, the
authentication and privacy algorithms and
parameters required to access the management
entity. In order for a SNMP manager to be able to
access the Party, that manager must have prior
knowledge of the Party.
A party is named by a 'Party'. For a
entity which is not managed through access to a
SNMP Party, the value of this object is 0.0ro Party (SNMPv2-PARTY-MIB) .1.3.6.1.4.1.22.101.6.1.2.3.1.1.7 |
chasEntityContextThe SNMPv2 Context indentifier the
chasEntityContext in conjunction with
chasEntityParty defines access to the MIB view for
this entity.ro Context (SNMPv2-PARTY-MIB) .1.3.6.1.4.1.22.101.6.1.2.3.1.1.8 |
chasEntityCommunityThe SNMP Community which executes at the address
chasEntityIpAddress, and provides access to the
detailed management information for this entity.
For a entity which is not managed through access
to a SNMP Community, the value of this object is
the zero-length string.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.3.1.1.9 |
chasEntityIpAddressThe address of the SNMP agent which responds to
messages for the SNMP Community identified by
chasEntityCommunity. When access is via proxy,
this variable contains the address of the proxy
agent.
For a entity which is not managed through access
to a SNMP Community, the value of this object is
0.0.0.0.ro IpAddress .1.3.6.1.4.1.22.101.6.1.2.3.1.1.10 |
chasResource OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.4 |
chasPhyResourceTableThis table defines a physical relationship
between physical modules and resources. A
resource is a building block. A resource defines
the type of relationship between entities. This
may be a back plane connection between physical
modules sharing the same entity. It may be a
network segment that connects multiple entities.
This table then defines the physical mapping of
resources and physical modules onto entities. SEQUENCE OF ChasPhyResourceEntry .1.3.6.1.4.1.22.101.6.1.2.4.1 |
chasPhyResourceEntryDefines a particular physical configuration
relationship.ro ChasPhyResourceEntry .1.3.6.1.4.1.22.101.6.1.2.4.1.1 |
chasPhyResLocationTypeA resource exists on a particular module. A
module is identified by it's physical location.
Physical location is defined by location type and an
instance of that physical location type. This
object defines the location type. This object can
be used in conjunction with chasPhyResLocation to
index the module table.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.1 |
chasPhyResLocationA resource exists on a particular module. A
module is identified by it's physical location.
Physical location is defined by location type and an
instance of that physical location type. This
object defines a particular instance of the
physical location.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.2 |
chasPhyResIndexA unique index for the chassis resource on this
particular physical module.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.3 |
chasPhyResTypeThe type of resource.ro OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.4 |
chasPhyResAssignmentThe physical module resource is
assigned to a specific entity. This object
defines the entity to which this resource is
currently assigned.
Notice, not all implementations may support this
object as read-write. If read-write is supported
assignment may still fail due to a number of
reasons such as insufficient resources, invalid
configuration.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.5 |
chasPhyResEntitySubIndexProvides a unique index that can be used to
identify the relationship in terms of the entity.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.1.1.6 |
chasLogResourceTableDefines a logical configuration relationship
which is a relationship between entities and
resources and the physical module that the
relationship exists on. SEQUENCE OF ChasLogResourceEntry .1.3.6.1.4.1.22.101.6.1.2.4.2 |
chasLogResourceEntryDefines a single logical relationship. ChasLogResourceEntry .1.3.6.1.4.1.22.101.6.1.2.4.2.1 |
chasLogResEntityThe entity ID for which this logical
configuration relationship exists.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.2.1.1 |
chasLogResEntitySubIndexThe entity sub index for which this logical
configuration relationship exists. The logical
relationship is identified by a resource
assignment to an entity. The sub index defines a
particular instance of the mapping of physical
configuration onto an entity.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.2.1.2 |
chasLogResLocationTypeA module is defined by it's physical location
type and an instance of that physical location.
This object defines the physical location type
portion of the physical module identifier that
this logical configuration exists for.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.2.1.3 |
chasLogResLocationA module is defined by it's physical location
type and an instance of that physical location.
This object defines the instance physical location
(location index) portion of the physical module
identifier that this logical configuration exists
for.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.2.1.4 |
chasLogResIndexThe value of this object refers to a particular
instance of a resource, as defined by
chasResourceIndex, for which this relationship is
defined. This together with
chasLogResLocationType and
chasLogResLocation completes the mapping of
the logical configuration on to the physical
module and resource combination.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.4.2.1.5 |
chasPowerSupply OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.5 |
chasPowerSupplyTableA list of power supply entries, one for each
power supply in the chassis. SEQUENCE OF ChasPowerSupplyEntry .1.3.6.1.4.1.22.101.6.1.2.5.1 |
chasPowerSupplyEntryValues for a power supply. ChasPowerSupplyEntry .1.3.6.1.4.1.22.101.6.1.2.5.1.1 |
chasPowerSupplyIndexAn index value that uniquely identifies a power
supply. This may correspond to a hardware power
supply slot, which may or may not be the same as a
network device slot (chasSlotIndex).ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.1.1.1 |
chasPowerSupplyDescrA textual description of the power supply,
including the vendor's name and version.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.5.1.1.2 |
chasPowerSupplyAdminStatusDesired status of the power supply.rw Enumeration .1.3.6.1.4.1.22.101.6.1.2.5.1.1.3 |
chasPowerSupplyOperStatusActual status of the power supply:
- unknown(1) - status not known.
- empty(2) - no power supply installed in slot
- disabled(3) - unable to supply power due to
chasPowerSupplyAdminStatus
- bad(4) - unable to supply power due to failure
- warning(5) - supplying power but an output or
sensor is bad or warning
- standby(6) - believed usable but not supplying power
- engaged(7) - supplying power
- redundant(8) - supplying power but not needed
It is an implementation specific matter whether
the agent keeps entries with status unknown(1) or
empty(2) in the table.ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.5.1.1.4 |
chasPowerSupplyHealthTextA textual description of the power supply's
operational status. Agents may use this string to
provide detailed information on current failures,
including how they were detected, and/or
instructions for problem resolution. The contents
are agent-specific.ro DisplayString .1.3.6.1.4.1.22.101.6.1.2.5.1.1.5 |
chasPowerSupplyWarningsThe number of times chasPowerSupplyOperStatus has
gone to warning(5).ro Counter .1.3.6.1.4.1.22.101.6.1.2.5.1.1.6 |
chasPowerSupplyFailuresThe number of times chasPowerSupplyOperStatus has
gone to bad(4).ro Counter .1.3.6.1.4.1.22.101.6.1.2.5.1.1.7 |
chasPowerSupplyLocationTypeThis defines the instance of a physical location
type of the power supply. Location Type together
with location index completely defines the
location of a power supply.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.1.1.8 |
chasPowerSupplyLocationIndexDefines a particular instance of a physical
location type.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.1.1.9 |
chasPowerSupplyOutputTableA list of power supply output entries, one for
each output of each power supply in the chassis. SEQUENCE OF ChasPowerSupplyOutputEntry .1.3.6.1.4.1.22.101.6.1.2.5.2 |
chasPowerSupplyOutputEntryValues for a power supply output. ChasPowerSupplyEntry .1.3.6.1.4.1.22.101.6.1.2.5.2.1 |
chasPowerSupplyIdIndexAn index value that uniquely identifies a power
supply. This may correspond to a hardware power
supply slot, which may or may not be the same as a
network device slot (chasSlotIndex).ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.2.1.1 |
chasPowerSupplyOutputIndexAn index value that uniquely identifies an output
for the power supply.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.2.1.2 |
chasPowerSupplyOutputStatusActual status of the power supply:
- unknown(1) status not known
- bad(2) unable to supply power due to
failure
- warning(3) supplying power but marginally
- good(4) supplying power
It is an implementation specific matter whether
the agent keeps entries with status unknown(1) in
the table. If unknown(1), offered values and
counters are meaningless.ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.5.2.1.3 |
chasPowerSupplyOutputNominalVoltageIn hundredths of a volt, the voltage
the output is supposed to supply, such
as -5, +5, +12, -15, etc.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.2.1.4 |
chasPowerSupplyOutputOfferedVoltageIn hundredths of a volt, the voltage
actually offered by the output. If
chasPowerSupplyOutputStatus is good(4),
the value 0 means offered voltage is
not available.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.2.1.5 |
chasPowerSupplyOutputOfferedWattageIn hundredths of a watt, the wattage
actually offered by the output. If
chasPowerSupplyOutputStatus is good(4),
the value 0 means offered wattage is not
available.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.5.2.1.6 |
chasPowerSupplyOutputWarningsThe number of times
chasPowerSupplyOutputStatus has gone to
warning(3).ro Counter .1.3.6.1.4.1.22.101.6.1.2.5.2.1.7 |
chasPowerSupplyOutputFailuresThe number of times
chasPowerSupplyOutputStatus has gone to
bad(2).ro Counter .1.3.6.1.4.1.22.101.6.1.2.5.2.1.8 |
chasEnviron OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.6 |
chasEnvironTableA list of environmental entries, one for
each environmental sensor in the chassis. SEQUENCE OF ChasEnvironEntry .1.3.6.1.4.1.22.101.6.1.2.6.1 |
chasEnvironEntryValues for a environmental sensor. ChasEnvironEntry .1.3.6.1.4.1.22.101.6.1.2.6.1.1 |
chasEnvironSensorThe identification of an environmental
sensor. Other AutonomousType values may be
defined elsewhere, in association with
specific protocols. However, this document
assigns those of known interest as of this
writing.ro AutonomousType .1.3.6.1.4.1.22.101.6.1.2.6.1.1.1 |
chasEnvironStatusActual status indicated by the sensor. It is
an implementation specific matter whether the
agent keeps entries with status unknown(1) in
the table. If unknown(1), counters are
meaningless.ro Enumeration .1.3.6.1.4.1.22.101.6.1.2.6.1.1.2 |
chasEnvironWarningsThe number of times chasEnvironStatus has gone
to warning(3).ro Counter .1.3.6.1.4.1.22.101.6.1.2.6.1.1.3 |
chasEnvironFailuresThe number of times chasEnvironStatus has gone
to bad(2).ro Counter .1.3.6.1.4.1.22.101.6.1.2.6.1.1.4 |
chasEnvironLocationTypeDefines the actual type of physical location
that this environmental sensor occupies.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.6.1.1.5 |
chasEnvironLocationIndexThis defines the particular instance of a
physical location type which this environmental
sensor occupies.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.6.1.1.6 |
chasEnvironIndexAn index value that uniquely identifies an
environmental sensor.ro INTEGER .1.3.6.1.4.1.22.101.6.1.2.6.1.1.7 |
chasKnownTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7 |
chasLocationTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1 |
chasModularSlot OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.1 |
chasPowerSupplyBay OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.2 |
chasFanTray OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.3 |
chasBackplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.4 |
chasFrontSlot OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.5 |
chasBackSlot OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.1.6 |
chasModuleTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.2 |
chasLocationEmpty OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.2.1 |
chasModuleUnknown OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.2.2 |
chasEntityTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3 |
chasChassisEntities OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.1 |
chasPowerSource OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.1.1 |
chasChassis OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.1.2 |
chasMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.1.3 |
chasNetEntities OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2 |
chas8023Repeater OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.1 |
chas8025Ring OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.2 |
chasFddiRing OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.3 |
chasAtmSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.4 |
chasFrameRelay OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.5 |
chasEthSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.2.6 |
chasConnectEntities OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.3 |
chasBridge OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.3.1 |
chasRouter OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.3.2 |
chasBrouter OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.3.3 |
chasGateway OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.3.3.4 |
chasResTypes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4 |
chasChassisRes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.1 |
chasNetworkRes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2 |
chas8023RptrPort OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.1 |
chas8025MauPort OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.2 |
chasFddiPort OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.3 |
chasAtmPort OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.4 |
chas8023PortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.5 |
chas8025PortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.6 |
chasFddiPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.7 |
chasAtmPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.2.8 |
chasBplaneRes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3 |
chas8023Bplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3.1 |
chas8025Bplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3.2 |
chasFddiBplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3.3 |
chasMgmtBplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3.4 |
chasAtmBplane OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.3.5 |
chasConnectRes OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.4 |
chasBridgeRelay OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.4.1 |
chasRouterRelay OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.4.2 |
chasBrouterRelay OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.4.3 |
chasSwitch OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.4.4.4 |
wellKnownSensors OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.5 |
sensorOther OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.5.1 |
sensorTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.5.2 |
sensorFans OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.5.3 |
sensorHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.6.1.2.7.5.4 |
mibsterminal-servers OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.7 |
mibseth-rptrs OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.8 |
mibsbridges OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9 |
mibbridges-specific OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.1 |
mibeth2fddi OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.1.1 |
mib-fx8616 OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.1.1.1 |
mibeth2eth OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.1.2 |
mib-xm516 OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.1.2.1 |
mibbridges-general OBJECT IDENTIFIER .1.3.6.1.4.1.22.101.9.2 |
nonProductsOids OBJECT IDENTIFIER .1.3.6.1.4.1.22.102 |
resource-oids OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1 |
eth-resources OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.1 |
esb-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.1.1 |
eb2-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.1.2 |
repeater-manager-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.1.3 |
eth-switch-resources OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.2 |
eb2-one-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.2.1 |
eb2-two-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.2.2 |
eb2-three-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.2.3 |
eb2-four-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.2.4 |
atm-switch-resources OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.3 |
em501-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.3.1 |
em502-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.3.2 |
tr-resources OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.4 |
tr4-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.4.1 |
tr16-resource OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.1.4.2 |
entity-oids OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.2 |
sensor-oids OBJECT IDENTIFIER .1.3.6.1.4.1.22.102.3 |