EDB-snmp
AI MIB Summary
Standard SNMP MIB module defining data structures for EDB-snmp.
114
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
114 total| Object Name |
|---|
private OBJECT IDENTIFIER .1.3.6.1.4 |
RFC1213-MIB Unknown .1.3.6.1.4 |
enterprises OBJECT IDENTIFIER .1.3.6.1.4.1 |
fibronics OBJECT IDENTIFIER .1.3.6.1.4.1.22 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.22.3 |
traprun OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.1 |
rTrapAddrTblTable of managers to which traps
must be sent. Up to 10
entries in table SEQUENCE OF RTrapAddrEntry .1.3.6.1.4.1.22.3.1.1 |
rTrapAddrEntry RTrapAddrEntry .1.3.6.1.4.1.22.3.1.1.1 |
rTrapAddrAddrIP address of entity
requesting event notificationrw IpAddress .1.3.6.1.4.1.22.3.1.1.1.1 |
rTrapAddrCommCommunity name the receiving
entity will expect.
When reading the instance of this
object the value has no meaning.rw OCTET STRING .1.3.6.1.4.1.22.3.1.1.1.2 |
rTrapAddrVerVersion number supported by
destination noderw INTEGER .1.3.6.1.4.1.22.3.1.1.1.3 |
rTrapAddrTypeType of event that should be
reported to this address,
bit 0 - authentication trap
bit 1 - other SNMP traps
bit 2 - Error Traps
bit 3 - Diagnostic Traps
bit 4 - Debug Traps
bit 5 - Enterprise Traps other than fmDiagGenericTraprw OCTET STRING .1.3.6.1.4.1.22.3.1.1.1.4 |
rTrapAddrStateDetermines status of this entryrw Enumeration .1.3.6.1.4.1.22.3.1.1.1.5 |
rTrapAddrFlagIf the entry is fixed, it can not
be deleted because of agingrw Enumeration .1.3.6.1.4.1.22.3.1.1.1.6 |
rTrapAddrAgeAging time of the entry (in sec)ro INTEGER .1.3.6.1.4.1.22.3.1.1.1.7 |
rTrapLearningLearn the addresses of the managers
automatically.ro Enumeration .1.3.6.1.4.1.22.3.1.2 |
rTrapAgingTime in sec. until we erase a trap
entryro INTEGER .1.3.6.1.4.1.22.3.1.3 |
traperm OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.2 |
pTrapAddrTblTable of managers to which traps
must be sent. Up to 10
entries in table SEQUENCE OF PTrapAddrEntry .1.3.6.1.4.1.22.3.2.1 |
pTrapAddrEntry PTrapAddrEntry .1.3.6.1.4.1.22.3.2.1.1 |
pTrapAddrAddrIP address of entity
requesting event notificationrw IpAddress .1.3.6.1.4.1.22.3.2.1.1.1 |
pTrapAddrCommCommunity name the receiving
entity will expect.
When reading the instance of this
object the value has no meaning.rw OCTET STRING .1.3.6.1.4.1.22.3.2.1.1.2 |
pTrapAddrVerVersion number supported by
destination noderw INTEGER .1.3.6.1.4.1.22.3.2.1.1.3 |
pTrapAddrTypeType of event that should be
reported to this address,
bit 0 - authentication trap
bit 1 - other SNMP traps
bit 2 - Error Traps
bit 3 - Diagnostic Traps
bit 4 - Debug Traps
bit 5 - all Enterprise Traps other than fmDiagGenericTraprw OCTET STRING .1.3.6.1.4.1.22.3.2.1.1.4 |
pTrapAddrStateDetermines status of this entryrw Enumeration .1.3.6.1.4.1.22.3.2.1.1.5 |
pTrapLearningLearn the addresses of the managers
automatically.rw Enumeration .1.3.6.1.4.1.22.3.2.2 |
pTrapAgingTime in sec. until we erase a trap
entryrw INTEGER .1.3.6.1.4.1.22.3.2.3 |
trapvar OBJECT IDENTIFIER .1.3.6.1.4.1.22.3.3 |
fm800 OBJECT IDENTIFIER .1.3.6.1.4.1.22.51 |
fmPowerSupplyFailThis trap message is generated as soon
as one of the power supply has failed TRAP-TYPE .1.3.6.1.4.1.22.51.0.1 |
fmPrimaryPowerSupplyOKThis trap is issued when primary power
supply return to work TRAP-TYPE .1.3.6.1.4.1.22.51.0.2 |
fmSecondPowerSupplyOKThis trap is issued when second power
supply return to work TRAP-TYPE .1.3.6.1.4.1.22.51.0.3 |
fmPowerSupplyChangeConfigIssued when a change in the configuration
of the power supply is done TRAP-TYPE .1.3.6.1.4.1.22.51.0.4 |
fmLUOutOfSyncIssued when the Logic unit goes
out of synchronization TRAP-TYPE .1.3.6.1.4.1.22.51.0.7 |
fmLUReturnToSyncIssues as soon as the logic unit
returns to synchronization TRAP-TYPE .1.3.6.1.4.1.22.51.0.8 |
fmLUPassToMainIssues as soon as the logic unit
pass to main link TRAP-TYPE .1.3.6.1.4.1.22.51.0.9 |
fmLUPassToSecondIssues as soon as the logic unit
pass to second link TRAP-TYPE .1.3.6.1.4.1.22.51.0.10 |
fmLUPrimaryLinkFailWhen primary link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.51.0.11 |
fmLUPrimaryLinkOKWhen primary link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.51.0.12 |
fmLUSecondLinkFailWhen second link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.51.0.13 |
fmLUSecondLinkOKWhen second link of the logic unit fails
this trap is issued TRAP-TYPE .1.3.6.1.4.1.22.51.0.14 |
fmLULLBOnWhen the logic unit enters LLB mode TRAP-TYPE .1.3.6.1.4.1.22.51.0.15 |
fmLULLBOffWhen the logic unit exits LLB mode TRAP-TYPE .1.3.6.1.4.1.22.51.0.16 |
fmLUChangeConfigIssues when a change in the LU configuration
is done TRAP-TYPE .1.3.6.1.4.1.22.51.0.20 |
fmSlotTrapGenerated when a significant status has
changed in a slot. By xoring the 2 statuses,
the NMS can identify the cause of the trap. TRAP-TYPE .1.3.6.1.4.1.22.51.0.25 |
fmSlotChangeConfigIssued when the system detects
changes in its slots configuration TRAP-TYPE .1.3.6.1.4.1.22.51.0.26 |
fmDiagGenericTrapGeneric Trap information TRAP-TYPE .1.3.6.1.4.1.22.51.0.30 |
fmsystem OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1 |
fmsystemrun OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1.1 |
fmSystemPSAdminChanges power supply to
primary or secondary.
When reading the instance of this
object the value has no meaning.rw Enumeration .1.3.6.1.4.1.22.51.1.1.1 |
fmSystemPSOperWhich power supply activero Enumeration .1.3.6.1.4.1.22.51.1.1.2 |
fmSystemPSCfgConfiguration of power supplyrw Enumeration .1.3.6.1.4.1.22.51.1.1.3 |
fmSystemResetResetting the CARD.
When reading the instance of this
object the value has no meaning.
cold reset is performed with selftest ,
while warm start is performed without
selftestrw Enumeration .1.3.6.1.4.1.22.51.1.1.4 |
fmSystemSelfTestLevelType of self test to be
executed upon cold-resetrw Enumeration .1.3.6.1.4.1.22.51.1.1.5 |
fmSystemVersionVersion of the station. The version includes
station type, hardware version and software version.
The string can include CR and LFro OCTET STRING .1.3.6.1.4.1.22.51.1.1.6 |
fmSystemIpAddrIP address of the agentro IpAddress .1.3.6.1.4.1.22.51.1.1.7 |
fmSystemIPNetMaskIP Network Maskro IpAddress .1.3.6.1.4.1.22.51.1.1.8 |
fmSystemIPDefGwayDefault Gateway Addressro IpAddress .1.3.6.1.4.1.22.51.1.1.9 |
fmSystemFileServerIP address to which a TFTP for boot is sent.rw IpAddress .1.3.6.1.4.1.22.51.1.1.10 |
fmSystemBootFilePath and file name that is
sent as a TFTP requestro OCTET STRING .1.3.6.1.4.1.22.51.1.1.11 |
fmSystemBootModeMethod for bootingrodeprecated Enumeration .1.3.6.1.4.1.22.51.1.1.12 |
fmSystemDownLoadDownloading the EDB.
When reading the instance of this
object the value has no meaning.rw Enumeration .1.3.6.1.4.1.22.51.1.1.13 |
fmSystemSlipIpAddrSLIP IP address.
This is object is available
only when slip interface existro IpAddress .1.3.6.1.4.1.22.51.1.1.14 |
fmSystemSlipIPNetMaskSLIP IP Network Mask
This is object is available
only when slip interface existro IpAddress .1.3.6.1.4.1.22.51.1.1.15 |
fmSystemSlipBaudRateSLIP Baud rate
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.16 |
fmSystemSlipParitySLIP Parity
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.17 |
fmSystemSlipStopBitsSLIP Stop Bits
This is object is available
only when slip interface existro Enumeration .1.3.6.1.4.1.22.51.1.1.18 |
fmsystemperm OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.1.2 |
pfmSystemIpAddrIP address of the agentrw IpAddress .1.3.6.1.4.1.22.51.1.2.7 |
pfmSystemIPNetMaskIP Network Maskrw IpAddress .1.3.6.1.4.1.22.51.1.2.8 |
pfmSystemIPDefGwayDefault Gateway Addressrw IpAddress .1.3.6.1.4.1.22.51.1.2.9 |
pfmSystemFileServerIP address to which a TFTP for boot is sent.rw IpAddress .1.3.6.1.4.1.22.51.1.2.10 |
pfmSystemBootFilePath and file name that is
sent as a TFTP requestrw OCTET STRING .1.3.6.1.4.1.22.51.1.2.11 |
pfmSystemBootModeMethod for bootingrw Enumeration .1.3.6.1.4.1.22.51.1.2.12 |
pfmSystemReadCommunityCommunity string for reading
When reading the instance of this
object the value has no meaning.rw OCTET STRING .1.3.6.1.4.1.22.51.1.2.13 |
pfmSystemWriteCommunityCommunity string for writing
When reading the instance of this
object the value has no meaning.rw OCTET STRING .1.3.6.1.4.1.22.51.1.2.14 |
pfmSystemSlipIpAddrSLIP IP address
This is object is available
only when slip interface existrw IpAddress .1.3.6.1.4.1.22.51.1.2.15 |
pfmSystemSlipIPNetMaskSLIP IP Network Mask
This is object is available
only when slip interface existrw IpAddress .1.3.6.1.4.1.22.51.1.2.16 |
pfmSystemSlipBaudRateSLIP Baud rate
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.17 |
pfmSystemSlipParitySLIP Parity
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.18 |
pfmSystemSlipStopBitsSLIP Stop Bits
This is object is available
only when slip interface existrw Enumeration .1.3.6.1.4.1.22.51.1.2.19 |
fmslot OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.2 |
fmSlotMasterClearUpon writing, performs a master
clear command on all the slots.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.1 |
fmSlotTable SEQUENCE OF FmSlotEntry .1.3.6.1.4.1.22.51.2.2 |
fmSlotEntry FmSlotEntry .1.3.6.1.4.1.22.51.2.2.1 |
fmSlotIndexSlot Numberro INTEGER .1.3.6.1.4.1.22.51.2.2.1.1 |
fmSlotIDID of the card in the slotrw Enumeration .1.3.6.1.4.1.22.51.2.2.1.2 |
fmSlotDescrAscii string. Description
of the cardro OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.3 |
fmSlotInfoUser general info for the slot.
Can be the use of that slot, its
location etc...rw OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.4 |
fmSlotStatus8 bytes. 60 status bits of
the card. For more information about
the meaning of the status, read the
specific user manual of each card.
The channel leds are encoded into
2 bytes.ro OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.5 |
fmSlotPrevStatus8 bytes. Previous 60 status
bits of the card. This
object id is used mainly
for traps (see Card Trap)ro OCTET STRING .1.3.6.1.4.1.22.51.2.2.1.6 |
fmSlotRLBSetArgument: 1 - 4. Perform a
RLB set operation on the
channel passed as argument.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.7 |
fmSlotRLBClearArgument: 1 - 4. Perform a
RLB clear operation on the
channel passed as argument.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.8 |
fmSlotExpCodePerform an expanded command
on the slot. For expanded codes,
see specific card user manual.
When reading the instance of this
object the value has no meaning.
Extended command codes for NDS cards
1. CC892.303 (Ethernet)
Code (Dec/Hex) Command
02/02 Detach Port 13
03/03 Attach Port 13
04/04 Detach Port 01
05/05 Attach Port 01
06/06 Detach Port 02
07/07 Attach Port 02
08/08 Detach Port 03
09/09 Attach Port 03
10/0A Detach Port 04
11/0B Attach Port 04
12/0C Detach Port 05
13/0D Attach Port 05
14/0E Detach Port 06
15/0F Attach Port 06
16/10 Detach Port 07
17/11 Attach Port 07
18/12 Detach Port 08
19/13 Attach Port 08
20/14 Detach Port 09
21/15 Attach Port 09
22/16 Detach Port 10
23/17 Attach Port 10
24/18 Detach Port 11
25/19 Attach Port 11
26/1A Detach Port 12
27/1B Attach Port 12
28/1C Detach All Ports
29/1D Attach All Ports
30/1E Reset Card
31/1F Link Select
======================================================
2. CC892.308 (Ethernet)
Code (Dec/Hex) Command
02/02 Detach Port 01
03/03 Attach Port 01
04/04 Detach Port 02
05/05 Attach Port 02
06/06 Detach Port 03
07/07 Attach Port 03
08/08 Detach Port 04
09/09 Attach Port 04
10/0A Detach Port 05
11/0B Attach Port 05
12/0C Detach Port 06
13/0D Attach Port 06
14/0E Detach Port 07
15/0F Attach Port 07
16/10 Detach Port 08
17/11 Attach Port 08
...
28/1C Detach All Ports
29/1D Attach All Ports
30/1E Reset Card
31/1F Link Select
================================================
3. CC892.322 (Token-ring)
Module 323
Code (Dec/Hex) Command
02/02 Detach Port 01
03/03 Attach Port 01
04/04 Detach Port 02
05/05 Attach Port 02
06/06 Detach Port 03
07/07 Attach Port 03
08/08 Detach Port 04
09/09 Attach Port 04
10/0A Detach Port 05
11/0B Attach Port 05
12/0C Detach Port 06
13/0D Attach Port 06
18/12 Detach Port 07
19/13 Attach Port 07
20/14 Detach Port 08
21/15 Attach Port 08
22/16 Detach Port 19
23/17 Attach Port 19
24/18 Detach Port 10
25/19 Attach Port 10
26/1A Detach Port 11
27/1B Attach Port 11
28/1C Detach Port 12
29/1D Attach Port 12
30/1E Reset Card
34/22 Detach Port 13
35/23 Attach Port 13
36/24 Detach Port 14
37/25 Attach Port 14
38/26 Detach Port 15
39/27 Attach Port 15
40/28 Detach Port 16
41/29 Attach Port 16
42/2A Detach Port 17
43/2B Attach Port 17
44/2C Detach Port 18
45/2D Attach Port 18
50/32 Detach Port 19
51/33 Attach Port 19
52/34 Detach Port 20
53/35 Attach Port 20
54/36 Detach Port 21
55/37 Attach Port 21
56/38 Detach Port 22
57/39 Attach Port 22
58/3A Detach Port 23
59/3B Attach Port 23
60/3C Detach Port 24
61/3D Attach Port 24
77/4D Detach All Ports
79/4F Attach All Ports
========================================================
Module 325
30/1E Reset Card
80/50 Detach Local Port 1 (channel 1)
81/51 Attach Local Port 1 (channel 1)
82/52 Detach Local Port 2 (channel 1)
83/53 Attach Local Port 2 (channel 1)
88/58 Detach Local Port 1 (channel 3)
89/59 Attach Local Port 1 (channel 3)
90/5A Detach Local Port 2 (channel 3)
91/5B Attach Local Port 2 (channel 3)
77/4D Detach All Ports
79/4F Attach All Ports
4. CC892.427 (Voice)
Code (Dec/Hex) Command
04/04 Loopback OFF on Port 1
05/05 Loopback ON on Port 1
06/06 Loopback OFF on Port 2
07/07 Loopback ON on Port 2
08/08 Loopback OFF on Port 3
09/09 Loopback ON on Port 3
10/0A Loopback OFF on Port 4
11/0B Loopback ON on Port 4
12/0C Loopback OFF on Port 5
13/0D Loopback ON on Port 5
14/0E Loopback OFF on Port 6
15/0F Loopback ON on Port 6
16/10 Loopback OFF on Port 7
17/11 Loopback ON on Port 7
18/12 Loopback OFF on Port 8
19/13 Loopback ON on Port 8
20/14 Loopback OFF on Port 9
21/15 Loopback ON on Port 9
22/16 Loopback OFF on Port 10
23/17 Loopback ON on Port 10
24/18 Loopback OFF on Port 11
25/19 Loopback ON on Port 11
26/1A Loopback OFF on Port 12
27/1B Loopback ON on Port 12
28/1C Loopback OFF on Port 13
29/1D Loopback ON on Port 13
30/1E Loopback OFF on Port 14
31/1F Loopback ON on Port 14
32/20 Loopback OFF on Port 15
33/21 Loopback ON on Port 15
34/22 Loopback OFF on Port 16
35/23 Loopback ON on Port 16
37/25 Loopback ALL on Ports 1-8
39/27 Loopback ALL on Ports 9-16
40/28 Alternate Mode on Channel Module #1
41/29 Normal Mode on Channel Module #1
42/2A Alternate Mode on Channel Module #2
43/2B Normal Mode on Channel Module #2
45/2D Configuration Load Module #1
47/2F Configuration Load Module #2
======================================================rw INTEGER .1.3.6.1.4.1.22.51.2.2.1.9 |
fmSlotTrapMaskWhen the value is 1, no more traps
from that slot are sent, until next reset.
(temporary mask)rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.10 |
pfmSlotTrapMaskWhen the value is 1, no more traps for that slot
will be sent, starting after next reset (permanent mask)rw Enumeration .1.3.6.1.4.1.22.51.2.2.1.11 |
fmSlotIpAddrIP address of a channel card.
This is object is available
only for channel cards which have their
own IP addresses (e.g., LC303/129)ro IpAddress .1.3.6.1.4.1.22.51.2.2.1.12 |
fmlu OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.3 |
fmLUIDLogic unit IDrw Enumeration .1.3.6.1.4.1.22.51.3.1 |
fmLUDescrAscii string. Description
of the logic unitro OCTET STRING .1.3.6.1.4.1.22.51.3.2 |
fmLUStatusOne byte of LU statusro OCTET STRING .1.3.6.1.4.1.22.51.3.3 |
fmLULinkSelectSetup LU link.rw Enumeration .1.3.6.1.4.1.22.51.3.4 |
fmLULoopBackSetUpon writing, performs LLB command.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.3.5 |
fmLULoopBackClrUpon writing, clear LLB command.
When reading the instance of this
object the value has no meaning.rw INTEGER .1.3.6.1.4.1.22.51.3.6 |
fmLUTrapMaskWhen the value is 1, no more traps
from the LU are sent, until next reset.
(temporary mask)rw Enumeration .1.3.6.1.4.1.22.51.3.7 |
pfmLUTrapMaskWhen the value is 1, no more traps for the LU
will be sent, starting after next reset (permanent mask)rw Enumeration .1.3.6.1.4.1.22.51.3.8 |
fmdiag OBJECT IDENTIFIER .1.3.6.1.4.1.22.51.5 |
fmDiagConfigVersion of the station. The version includes
station type, hardware version and software version.
The string can include CR and LFro OCTET STRING .1.3.6.1.4.1.22.51.5.1 |
fmDiagTrapInfoUsed for generic traps. The first word
is the trap code. The rest of the string is
the extra information. Contains CR and LF char.ro DisplayString .1.3.6.1.4.1.22.51.5.2 |
fmDiagFaultTableTable of fault reports from the agent SEQUENCE OF FmDiagFaultEntry .1.3.6.1.4.1.22.51.5.3 |
fmDiagFaultEntry FmDiagFaultEntry .1.3.6.1.4.1.22.51.5.3.1 |
fmDiagFaultIndexThe fault index in the
fault tablero INTEGER .1.3.6.1.4.1.22.51.5.3.1.1 |
fmDiagFaultReportGet the faults detected by the agentro DisplayString .1.3.6.1.4.1.22.51.5.3.1.2 |
fmDiagDebugThis object is for factory use only. Users must not
write into this variable or improper operation
can occur.rw Enumeration .1.3.6.1.4.1.22.51.5.4 |