E5-110-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
764
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
764 total| Object Name |
|---|
calixNetworks OBJECT IDENTIFIER .1.3.6.1.4.1.6321 |
RFC1155-SMI Unknown .1.3.6.1.4.1.6321 |
calixRegistrations OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1 |
calixProducts OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2 |
e5x100 OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3 |
e5x110 OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1 |
alarmconf OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.2 |
alarmOpsThe manager sets the corresponding bit value to 1 to start the operation
and the agent clears the object to zero when the operation is successfully completed.
The various bit positions are:
BIT 1: clear
BIT 2: cutoffrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.1 |
alarmConfTableThis table includes alarm configuration. SEQUENCE OF AlarmConfEntry .1.3.6.1.4.1.6321.1.2.3.1.2.2 |
alarmConfEntryAn entry in alarmConfTable. AlarmConfEntry .1.3.6.1.4.1.6321.1.2.3.1.2.2.1 |
alarmConfId5000:adslLine_up
5001:adslLine_down
5002:adslPerf_lol_thresh
5003:adslPerf_lof_thresh
5004:adslPerf_los_thresh
5005:adslPerf_lop_thresh
5006:adslPerf_es_thresh
5007:adslPerf_ses_thresh
5008:adslPerf_uas_thresh
5009:adslAtuc_loftrap
5010:adslAtuc_lostrap
5011:adslAtur_loftrap
5012:adslAtur_lostrap
5013:adslAtur_lprtrap
5014:ad_dhcp_rt_full
5015:ad_dhcp_dm_conflict
5016:ad_dhcp_entry_full
5017:ad_dhcp_ip_dup
5018:ad_dhcp_mac_dup
10000:eqptVol_err
10001:eqptEqpttemp_err
10002:eqptFan_err
10003:eqptHw_rtc_fail
10004:eqptHw_mon_fail
10005:eqptCold_start
10006:eqptWarm_start
10007:eqptAlm_input
10008:eqptI2c_err
10009:eqptAlm_input2
10010:eqptAlm_input3
15000:sysReboot
15001:sysAco
15002:sysAlm_clear
15003:sysLogin_fail
15004:sysAnti_spoofing
15005:sysAlm_svrty_change
20000:enetUp
20001:enetDownro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.2.1.1 |
alarmConfFacilityAlarm facility.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.2.2.1.2 |
alarmConfTargetThe destination which alarms are reported to. Set the bit to 1 to enable the target.
BIT 1: snmp trap
BIT 2: syslogrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.2.1.3 |
alarmConfSeverityAlarm severityrw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.2.2.1.4 |
alarmConfClearableSetting the object to one indicates that the alarm is to be cleared when user submits alarm clear.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.2.2.1.5 |
alarmCurrTableThis table includes current alarm information. SEQUENCE OF AlarmCurrEntry .1.3.6.1.4.1.6321.1.2.3.1.2.3 |
alarmCurrEntryAn entry in alarmCurrTable. AlarmCurrEntry .1.3.6.1.4.1.6321.1.2.3.1.2.3.1 |
alarmCurrIndexIndex of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.1 |
alarmCurrOccurTimeAlarm occurence time (in hundredths of a second) since the system was last re-initialized.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.2 |
alarmCurrTrapOidTrap OID of the alarm.ro OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.3 |
alarmCurrParam1The 1st parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.4 |
alarmCurrParam2The 2nd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.5 |
alarmCurrParam3The 3rd parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.6 |
alarmCurrParam4The 4th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.7 |
alarmCurrParam5The 5th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.8 |
alarmCurrParam6The 6th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.9 |
alarmCurrParam7The 7th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.10 |
alarmCurrParam8The 8th parameter of the alarm.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.11 |
alarmCurrTimeDescrThe string representation of occurence time (YYYY/MM/DD HH:MM:SS).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.12 |
alarmCurrSeverityThe severity of the alarm.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.13 |
alarmCurrDescrThe description of the alarm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.2.3.1.14 |
alarmSeverityPortTableThis table includes the configuration of alarm reporting severity threshold for each port. SEQUENCE OF AlarmSeverityPortEntry .1.3.6.1.4.1.6321.1.2.3.1.2.4 |
alarmSeverityPortEntryAn entry in alarmSeverityPortTable. AlarmSeverityPortEntry .1.3.6.1.4.1.6321.1.2.3.1.2.4.1 |
severityThreshThe minimum alarm severity that is reported.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.2.4.1.1 |
diagnostic OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.4 |
selt OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.4.3 |
seltTargetIfIndex of the port which would be performed single end loopback test.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.4.3.1 |
seltOpsThe manager sets the object to 1 to start the selt
and the agent clears the object to zero when selt is successfully completed.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.4.3.2 |
seltStatusStatus description of the selt result.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.4.3.3 |
seltCableTypeThe cable type that selt result indicates.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.4.3.4 |
seltLoopEstimateLengthFtThe estimated loop length that selt result indicates.ro INTEGER UNITS "feet" .1.3.6.1.4.1.6321.1.2.3.1.4.3.5 |
seltLoopEstimateLengthMeterThe estimated loop length that selt result indicates.ro INTEGER UNITS "meter" .1.3.6.1.4.1.6321.1.2.3.1.4.3.6 |
multicast OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7 |
igmpEnableEnable/disable IGMP protocol.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.1 |
mcastBandwidth OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.4 |
mcastDefaultBandwidthDefault bandwidth requirement for a multicast channel.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.4.1 |
maxNumOfMcastBwThe maximum number of row entries that user can create in mcastBwTable.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.4.2 |
mcastBwTableThis table defines bandwidth budget for a range of multicast IP channels. SEQUENCE OF McastBwEntry .1.3.6.1.4.1.6321.1.2.3.1.7.4.3 |
mcastBwEntryAn entry of mcastBwTable. McastBwEntry .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1 |
mcastBwIndexThe index which specify the entry.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.1 |
mcastBwStartIpThe start multicast IP of the bandwidth control range.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.2 |
mcastBwEndIpThe end multicast IP of the bandwidth control range.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.3 |
mcastBwBandwidthThe bandwidth budget for the multicast IP channels.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.4 |
mcastBwRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.7.4.3.1.5 |
mcastBwPortTableThis table specify the multicast bandwidth control of the port. SEQUENCE OF McastBwPortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.4.4 |
mcastBwPortEntryAn entry of mcastBwPortTable. McastBwPortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1 |
mcastBwPortEnableEnable/disable multicast bandwidth control for a port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.1 |
mcastBwPortBandwidthSet bandwidth threshold for a port.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.7.4.4.1.2 |
igmpCount OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.5 |
igmpCountPortTableThis table specify the IGMP count limiting of the port. SEQUENCE OF IgmpCountPortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.5.1 |
igmpCountPortEntryAn entry of igmpCountPortTable. IgmpCountPortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1 |
igmpCountPortEnableEnable/disable IGMP count limiting for a port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.1 |
igmpCountPortLimitThe maximum allowed IGMP report count for a port.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.5.1.1.2 |
mvlan OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.6 |
maxNumOfMvlanThe maximum number of row entries that user can create in mvlanTable.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.6.1 |
mvlanTableA table containing static configuration information for
each multicast VLAN configured into the device. SEQUENCE OF MvlanEntry .1.3.6.1.4.1.6321.1.2.3.1.7.6.2 |
mvlanEntryAn entry of mvlanTable. MvlanEntry .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1 |
mvlanIndexThe VLAN-ID refering to this VLAN.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.1 |
mvlanNameAn administratively assigned string, which may be used to identify the VLAN.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.2 |
mvlanEgressPortsThe set of ports which are permanently assigned to the
egress list for this multicast VLAN.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.3 |
mvlanUntaggedPortsThe set of ports which should transmit egress packets
for this multicast VLAN as untagged.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.4 |
mvlanRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.7.6.2.1.5 |
mvlanTranslateTableA table that contains multicast to VLAN translation. SEQUENCE OF MvlanTranslateEntry .1.3.6.1.4.1.6321.1.2.3.1.7.6.3 |
mvlanTranslateEntryAn entry of mvlanTranslateTable. MvlanTranslateEntry .1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1 |
mvlanTranslateIndexThe index which specif the entry.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.1 |
mvlanTranslateStartIpThe start IP of the multicast VLAN translation.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.2 |
mvlanTranslateEndIpThe end IP of the multicast VLAN translation.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.6.3.1.3 |
queryVid OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.7 |
maxNumOfQryVidThe maximum number of row entries that user can create in qryVidConfTable.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.7.1 |
qryVidConfTableThis table defines statically set VLANs used for response IGMP report. SEQUENCE OF QryVidConfEntry .1.3.6.1.4.1.6321.1.2.3.1.7.7.2 |
qryVidConfEntryAn entry in qryVidConfTable. QryVidConfEntry .1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1 |
qryVidVLAN ID.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.1 |
qryVidRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.7.7.2.1.2 |
qryVidStatusTableThis table shows statically set or dynamically learned VLANs used for response IGMP report. SEQUENCE OF QryVidStatusEntry .1.3.6.1.4.1.6321.1.2.3.1.7.7.3 |
qryVidStatusEntryAn entry in qryVidStatusTable. QryVidStatusEntry .1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1 |
qryVidTypeVLAN type.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.7.3.1.1 |
igmpVersionSetting IGMP version.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.9 |
igmpLeaveModeConfigure IGMP leave message handling mode.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.10 |
igmpTimer OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.11 |
igmpQryIntervalSet IGMP query interval, 10~1000 in seconds.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.11.1 |
igmpRobustSet IGMP query Robustness, 1~5.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.11.2 |
igmpQryRespIntervalSet IGMP query response interval, 1~100 in 100 milliseconds.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.11.3 |
igmpLastMemQryIntervalSet IGMP Last Member Query interval, 1~5 in 100 milliseconds.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.11.4 |
igmpLastMemQryRobustSet Last Member Query Robustness, 1~5.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.11.5 |
auditQuery OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.12 |
auditQryEnableEnable/disable IGMP audit query.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.12.1 |
auditQryIntervalSet IGMP Audit Query Interval, 1~4 in 100 milliseconds.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.12.2 |
auditQryRobustSet IGMP Audit Query Robustness, 1~5.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.12.3 |
igmpProfile OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.7.13 |
maxNumberOfIgmpProfilesThe max number of IGMP profiles in the system.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.13.1 |
igmpProfileTableA table that contains IGMP Profiles. SEQUENCE OF IgmpProfileEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.2 |
igmpProfileEntryThe entry of IGMP Profile table. IgmpProfileEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1 |
igmpProfileNameThe IGMP Profile name.ro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.1 |
igmpProfileEnableEnable/disable IGMP Profile.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.2 |
igmpProfileMaxGroupSet maximum allowed multicast group, 1~16.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.3 |
igmpProfileRowStatusThe row status of the IGMP Profile entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.7.13.2.1.4 |
igmpFilterTableA table that contains IGMP Filters. SEQUENCE OF IgmpFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.3 |
igmpFilterEntryThe entry of IGMP Filter table. IgmpFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1 |
igmpFilterIndexThe index which specifies the filter rule.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.1 |
igmpFilterStartIpThe start IP of the filter rule.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.2 |
igmpFilterEndIpThe end IP of the filter rule.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.7.13.3.1.3 |
igmpProfilePortTableThis table specifies the IGMP Profile of the port. SEQUENCE OF IgmpProfilePortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.4 |
igmpProfilePortEntryAn entry in igmpProfilePortTable. IgmpProfilePortEntry .1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1 |
igmpProfilePortProfileThe IGMP Profile of the port.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.7.13.4.1.1 |
port OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8 |
subrPortTableThis table includes subscriber attributes for the port. SEQUENCE OF SubrPortEntry .1.3.6.1.4.1.6321.1.2.3.1.8.1 |
subrPortEntryAn entry in subrPortTable. SubrPortEntry .1.3.6.1.4.1.6321.1.2.3.1.8.1.1 |
subrPortNameName of the subscriber.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.1.1.1 |
subrPortTelTelephone number of the subscriber.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.1.1.2 |
adslPort OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.2 |
adslLineConfTableThis table includes common attributes describing the ADSL line. SEQUENCE OF AdslLineConfEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.1 |
adslLineConfEntryAn entry in adslLineConfTable. AdslLineConfEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1 |
adslLineConfAdslModeG.lite and T1.413 are only applicable to annex A board.
ETSI is only applicable to annex B board.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.1 |
adslLineConfAnnexLEnable/disable annex L for the port(Only in AnnexA).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.2 |
adslLineConfAnnexMEnable/disable annex M for the port(For BCM AnnexA solution).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.3 |
adslLineConfAnnexIEnable/disable annex I for the port(For BCM AnnexA solution).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.4 |
adslLineConfOptionMaskThe semantic for each bit is:
BIT 1 : Disable Trellis
BIT 2 : Disable Reed-Solomon
BIT 3 : Disable upstream bitswap
BIT 4 : Disable downstream bitswap
BIT 5 : Disable 1-bit constellation
BIT 6 : Disable transmit windowing
BIT 7 : Disable s=0.5 support (ADSL1 only)
BIT 8 : Disable G.lite rate limit (ADSL1 only)
BIT 9 : Enable Nitro
BIT 10: Enable US PHYR
BIT 11: ENABLE DS PHYRrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.5 |
adslLineConfPowerMgmtEnable/disable power management for the port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.6 |
adslLineConfPowerModeThe power mode of the ADSL line.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.7 |
adslLineConfAturMaxTxPowerThe maximum allowed transmit power of ATU-R.rw INTEGER (-130..200) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.8 |
adslLineConfAtucMaxTxPowerThe maximum allowed transmit power of ATU-C.rw INTEGER (-50..200) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.9 |
adslLineConfMaxRxPowerThe maximum aggregate received power.rw INTEGER (-255..255) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.10 |
adslLineConfAturCarrierMaskThe upstream carrier mask. For CTLM AnnexA solution, bin is from 0 to 31;
CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63.
Bit set to 1 indicates the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.11 |
adslLineConfAtucCarrierMask0The downstream carrier mask. For CTLM AnnexA solution, bin is from 32 to 255;
CTLM AnnexB solution, bin is from 64 to 255; BCM solution, bin is from 32 to 255.
Bit set to 1 indicates the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.12 |
adslLineConfAtucCarrierMask1The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.13 |
adslLineConfAturInpThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol.
For CTLM solution, user can set value from 1 ~ 4,
but for BCM solution, user can set value from 1 ~ 7.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.14 |
adslLineConfAtucInpThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol.
For CTLM solution, user can set value from 1 ~ 4,
but for BCM solution, user can set value from 1 ~ 7.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.15 |
adslLineConfL0TimeSet the minimum time in seconds that the ADSL line
must stay in L0 power mode before changing to the L2 power mode.
For CTLM solution, the range is 120 ~ 65535;
for BCM solution, the range is 10 ~ 65535.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.16 |
adslLineConfL2TimeSet minimum time in seconds that the ADSL line must stay in the
L2 power mode before reducing the power again in the L2 power mode.
For CTLM solution, the range is 60 ~ 65535;
for BCM solution, the range is 10 ~ 65535.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.17 |
adslLineConfL2ATPRSet the maximum Aggregate Transmit Power Reduction (ATPR)
in decibels (dB) that is permitted in a L2 power reduction.
The system can gradually decrease the ADSL line transmission power
while it is in the L2 power mode. This is the largest individual
power reduction allowed in the L2 power mode.
For CTLM solution, the range is 1 ~ 5(dB);
for BCM solution, the range is 0 ~ 15(dB).rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.18 |
adslLineConfL2ATPRTthe maximum Aggregate Transmit Power Reduction Total (ATPRT)
in decibels (dB) that is permitted in the L2 power mode.
This is the total transmit power decrease that is allowed
to occur in the L2 power mode.
For CTLM solution, the range is 1 ~ 40(dB);
for BCM solution, the range is 0 ~ 15(dB).rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.19 |
adslLineConfMaxL2Rateconfigured maximum L2 rate.
(32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.20 |
adslLineConfMinL2Rateconfigured minimum L2 rate.
(32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.21 |
adslLineConfL0toL2Rateconfigured transition L0 to L2 rate.
(<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.22 |
adslLineConfNitroEnable/disable nitro mode for the port(For BCM solution).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.23 |
adslLineConfUSPhyrEnable/disable Upstream PHYR for the port(For BCM solution).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.24 |
adslLineConfDSPhyrEnable/disable Downstream PHYR for the port(For BCM solution).rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.1.1.25 |
adslPortBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3 |
adslPortTargetThe managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: 0, Reserved(chaises)
Byte 2~3: 0,0 Reserved(slot)
Byte 4: 0, reserved
Byte 5~11:each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.1 |
adslPortOpsThe managed object is for ADSL line configuration. When the EMS
wants to issue the desired operation, the EMS shall send SNMP-SET message to set
the corresponding bit value to be 1. The various bit positions are:
BIT 1: enable port
BIT 2: disable port
BIT 3: set ADSL mode
BIT 4: set line profile
BIT 5: set alarm profile
BIT 6: enable Annex L to be narrow mode(Only in AnnexA)
BIT 7: enable Annex L to be wide mode(Only in AnnexA)
BIT 8: disable Annex L(Only in AnnexA)
BIT 9: enable Annex M (For BCM AnnexA solution)
BIT 10: disable Annex M (For BCM AnnexA solution)
BIT 11: enable Annex I (For BCM AnnexA solution)
BIT 12: disable Annex I (For BCM AnnexA solution)
BIT 13: set option mask
BIT 14: enable power management mode to be L2
BIT 15: enable power management mode to be L2
BIT 16: disable power management mode
BIT 17: set power mode to be fixed
BIT 18: set power mode to be priority to power
BIT 19: set power mode to be priority to rate
BIT 20: set ATU-R max Tx power
BIT 21: set ATU-C max Tx power
BIT 22: set max Rx power
BIT 23: set ATU-R carrier mask
BIT 24: set ATU-C carrier mask
BIT 25: set ATU-R INP minimum setting
BIT 26: set ATU-C INP minimum settingrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.2 |
adslPortOps2The managed object is for ADSL line configuration. When the EMS
wants to issue the desired operation, the EMS shall send SNMP-SET message to set
the corresponding bit value to be 1. The various bit positions are:
BIT 1: set L0 Time
BIT 2: set L2 Time
BIT 3: set L2 ATPR
BIT 4: set L2 ATPRT
BIT 5: set maximum L2 rate
BIT 6: set minimum L2 rate
BIT 7: set transition L0 to L2 raterw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.3 |
adslModeForBatchSetG.lite and T1.413 are only applicable to annex A board.
ETSI is only applicable to annex B board.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.4 |
adslLineProfileForBatchSetThe ADSL line profile.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.5 |
adslAlarmProfileForBatchSetThe ADSL alarm profile.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.6 |
adslOptionMaskForBatchSetThe semantic for each bit is identical to the object adslLineConfOptionMask.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.7 |
adslAturMaxTxPowerForBatchSetThe maximum allowed transmit power of ATU-R.rw INTEGER (-130..200) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.8 |
adslAtucMaxTxPowerForBatchSetThe maximum allowed transmit power of ATU-C.rw INTEGER (-50..200) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.9 |
adslMaxRxPowerForBatchSetThe maximum aggregate received power.rw INTEGER (-255..255) UNITS "tenth dBm" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.10 |
adslAturCarrierMaskForBatchSetThe upstream carrier mask.For CTLM AnnexA solution, bin is from 0 to 31;
CTLM AnnexB solution, bin is from 0 to 63; BCM solution, bin is from 0 to 63.
Bit set to 1 indicates the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.11 |
adslAtucCarrierMask0ForBatchSetThe downstream carrier mask from bin 32 to 255. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.12 |
adslAtucCarrierMask1ForBatchSetThe downstream carrier mask from bin 256 to 511. Bit set to 1 indicates
the bin is masked off.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.13 |
adslAturInpForBatchSetThe upstream Impulse Noise Protection minimum setting in unit of DMT symbol.
For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.14 |
adslAtucInpForBatchSetThe downstream Impulse Noise Protection minimum setting in unit of DMT symbol.
For CTLM solution, user can set value from 1 ~ 4, but for BCM solution, user can set value from 1 ~ 7.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.15 |
adslL0TimeForBatchSetSet the minimum time in seconds that the ADSL line
must stay in L0 power mode before changing to the L2 power mode.
For CTLM solution, the range is 120 ~ 65535; for BCM solution, the range is 10 ~ 65535.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.16 |
adslL2TimeForBatchSetSet minimum time in seconds that the ADSL line
must stay in the L2 power mode before reducing the power
again in the L2 power mode.
For CTLM solution, the range is 60 ~ 65535; for BCM solution, the range is 10 ~ 65535.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.17 |
adslL2ATPRForBatchSetSet the maximum Aggregate Transmit Power Reduction (ATPR)
in decibels (dB) that is permitted in a L2 power reduction.
The system can gradually decrease the ADSL line transmission power
while it is in the L2 power mode. This is the largest individual
power reduction allowed in the L2 power mode.
For CTLM solution, the range is 1 ~ 5(dB); for BCM solution, the range is 0 ~ 15(dB).rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.18 |
adslL2ATPRTForBatchSetthe maximum Aggregate Transmit Power Reduction Total (ATPRT)
in decibels (dB) that is permitted in the L2 power mode.
This is the total transmit power decrease that is allowed
to occur in the L2 power mode.
For CTLM solution, the range is 1 ~ 40(dB); for BCM solution, the range is 0 ~ 15(dB).rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.19 |
adslMaxL2RateForBatchSetconfigured maximum L2 rate.
(32~4096 Kbps, 4 Kbps resolution. For CTLM solution, 0 for system assign; for BCM solution, default:4096.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.20 |
adslMinL2RateForBatchSetconfigured minimum L2 rate.
(32~4096 Kbps, 4 Kbps resolution, For CTLM solution, 0 for system assign; for BCM solution, default:32.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.21 |
adslL0toL2RateForBatchSetconfigured transition L0 to L2 rate.
(<=min_l2rate/2 and >= 16 Kbps, For CTLM solution, 0 for system assign; for BCM solution, default:16.)rw INTEGER UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.3.22 |
adslLineStatusTableThis table includes the ADSL line status. SEQUENCE OF AdslLineStatusEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.4 |
adslLineStatusEntryAn entry in adslLineStatusTable. AdslLineStatusEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1 |
adslLineStatusModeThe link up mode of the ADSL line.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.1 |
adslLineUpTimeThe link up time of the ADSL line, in unit of secondsro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.2.4.1.2 |
powerMgmtParamTableThis table defines L0 to L2 power transition parameters. SEQUENCE OF PowerMgmtParamEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.5 |
powerMgmtParamEntryAn entry in powerMgmtParamTable. PowerMgmtParamEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1 |
powerMgmtL0TimeThe object specifies the minimum time in L0 mode before L2 mode may be entered.rw INTEGER UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.1 |
powerMgmtL2TimeThe object specifies the minimum time in L2 mode before trimming and in between power trims.rw INTEGER UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.2 |
powerMgmtL2AtprThe maximum Aggregate Transmit Power Reduction.rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.3 |
powerMgmtL2AtprtThe maximum Aggregate Transmit Power Reduction Total.rw INTEGER UNITS "dB" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.4 |
powerMgmtL2MinRateThe object specifies the minimum L2 rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.5 |
powerMgmtL2MaxRateThe object specifies the maximum L2 rate.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.6 |
powerMgmtL2ThreshRateThe object specifies the rate threshold that triggers the line entering L0 or L2 mode.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.2.5.1.7 |
powerMgmtPSDTableThis table provides the PSD setting for both ATU-C and ATU-R. SEQUENCE OF PowerMgmtPSDEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.6 |
powerMgmtPSDEntryAn entry in powerMgmtPSDTable. PowerMgmtPSDEntry .1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1 |
powerMgmtAtucMaxPSDThe object specifies the maximum ATU-C PSD.rw INTEGER UNITS "0.1dBm/Hz" .1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.1 |
powerMgmtAturMaxPSDThe object specifies the maximum ATU-R PSD.rw INTEGER UNITS "0.1dBm/Hz" .1.3.6.1.4.1.6321.1.2.3.1.8.2.6.1.2 |
pvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.4 |
maxNumOfPvcsThe maximum number of PVCs which could be created on a port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.1 |
pvcTableThis table includes PVC configuration. SEQUENCE OF PvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.2 |
pvcEntryAn entry in pvcTable. PvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1 |
pvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.1 |
pvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.2 |
pvcPvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.3 |
pvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.5 |
pvcProfileDSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in DS side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.6 |
pvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.7 |
pvcProfileUSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in US side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.8 |
pvcAcNameAccess concentrator name for paepvc.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.11 |
pvcServiceNameService name for paepvc.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.12 |
pvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.8.4.2.1.13 |
pvcStateTableThis table show current PVC status.ro SEQUENCE OF PvcStateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.3 |
pvcStateEntryAn entry in pvcStateTable.ro PvcStateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1 |
pvcStateVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.1 |
pvcStateVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.2 |
pvcStatePvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.3 |
pvcStatePriority802.1p default priority of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.4 |
pvcStateChannelTypeThe value of this object identifies the channel type at runtime.ro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.8 |
pvcStateEncapThe value of this object identifies the channel encapsulation at runtime.ro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.4.3.1.9 |
pvcUsRateLimitTableThis table defines the upstream rate limit for each PVC. SEQUENCE OF PvcUsRateLimitEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.4 |
pvcUsRateLimitEntryAn entry in pvcUsRateLimitTable. PvcUsRateLimitEntry .1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1 |
pvcUsRateLimitEnableEnable/disable upstream rate limit for a PVC.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.1 |
pvcUsRateLimitUpstream rate limit in Kbps for a PVC.rw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.4.4.1.2 |
ppvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.5 |
maxNumOfPriorityPvcsThe maximum number of priority PVCs which could be created on a port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.1 |
ppvcTableThis table includes priority PVC configuration. SEQUENCE OF PpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.5.2 |
ppvcEntryAn entry in ppvcTable. PpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1 |
ppvcVpiVPI of the ppvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.1 |
ppvcVciVCI of the ppvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.2 |
ppvcPvidDefault VID of the ppvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.3 |
ppvcEncapEncapsulation of the ppvc.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.4 |
ppvcPriority802.1p default priority of the ppvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.5 |
ppvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.5.2.1.6 |
ppvcMemberTableThis table includes priority PVC member configuration. SEQUENCE OF PpvcMemberEntry .1.3.6.1.4.1.6321.1.2.3.1.8.5.4 |
ppvcMemberEntryAn entry in ppvcMemberTable. PpvcMemberEntry .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1 |
ppvcMemberVpiVPI of the member ppvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.1 |
ppvcMemberVciVCI of the member ppvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.2 |
ppvcMemberPriority802.1p default priority of the member ppvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.3 |
ppvcMemberProfileDSThe profile of the member ppvc in DS side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.4 |
ppvcMemberRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.5 |
ppvcMemberProfileUSThe profile of the member ppvc in US side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.5.4.1.6 |
rpvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.8 |
rpvcGatewayTableThis table includes Routed Gateway configuration. SEQUENCE OF RpvcGatewayEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.1 |
rpvcGatewayEntryAn entry in Routed Gateway table. RpvcGatewayEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1 |
rpvcGatewayIpIP of RPVC gateway.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.1 |
rpvcGatewayVlanIdVlan id send to this RPVC gateway.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.2 |
rpvcGatewayRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.3 |
rpvcGatewayPriority802.1p p bit send to this RPVC gateway.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.1.1.4 |
rpvcTableThis table includes RPVC configuration. SEQUENCE OF RpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.2 |
rpvcEntryAn entry in rpvcTable. RpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1 |
rpvcVpiVPI of the rpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.1 |
rpvcVciVCI of the rpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.2 |
rpvcDSProfileThe down stream profile of the rpvc.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.3 |
rpvcUSProfileThe up stream profile of the rpvc.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.4 |
rpvcIpThe IP of the rpvc.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.5 |
rpvcNetmaskThe IP mask of the rpvc IP.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.6 |
rpvcGatewayIpAddressThe gateway IP of rpvc.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.7 |
rpvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.8.2.1.8 |
rpvcRouteDomainTableThis table includes RPVC route domain configuration. SEQUENCE OF RpvcRouteDomainEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.3 |
rpvcRouteDomainEntryAn entry in rpvcRouteDomainTable. RpvcRouteDomainEntry .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1 |
rpvcRouteDomainVpiVPI of the rpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.1 |
rpvcRouteDomainVciVCI of the rpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.2 |
rpvcRouteDomainIpThe route domain IP.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.3 |
rpvcRouteDomainNetmaskThe IP mask of the route domain IP.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.4 |
rpvcRouteDomainRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.8.3.1.5 |
rpvcArpAgingTimeSet RPVC ARP proxy aging time 10..10000 seconds,
0 to disable againg.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.8.4 |
rpvcArpFlushFlush the RPVC ARP proxy table.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.8.5 |
dsBcastDisableTableThis table includes Down Stream Bcast configuration. SEQUENCE OF DsBcastDisableEntry .1.3.6.1.4.1.6321.1.2.3.1.8.9 |
dsBcastDisableEntryAn entry in Down Stream Bcast table. DsBcastDisableEntry .1.3.6.1.4.1.6321.1.2.3.1.8.9.1 |
dsBcastDisableVlanIddownstream broadcast disabled vid.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.9.1.1 |
dsBcastDisableRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.9.1.2 |
paepvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.10 |
paepvcTableThis table includes PPPoAoE PVC configuration. SEQUENCE OF PaepvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.10.1 |
paepvcEntryAn entry of paepvcTable. PaepvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1 |
paepvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.1 |
paepvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.2 |
paepvcPvidDefault VID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.3 |
paepvcPriority802.1p default priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.5 |
paepvcProfileDSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in DS side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.6 |
paepvcAcNameAccess concentrator name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.7 |
paepvcServiceNameService name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.8 |
paepvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through
during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.9 |
paepvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.10 |
paepvcProfileUSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in US side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.11 |
paepvcCvidDefault C-VID of the pvc.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.12 |
paepvcCPriority802.1p default C-priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.10.1.1.13 |
tlspvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.11 |
tlspvcTableThis table includes Transparent LAN Service (TLS) PVC configuration. SEQUENCE OF TlspvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.11.1 |
tlspvcEntryAn entry of tlspvcTable. TlspvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1 |
tlspvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.1 |
tlspvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.2 |
tlspvcSvids-tag VLAN ID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.3 |
tlspvcSprioritys-tag priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.5 |
tlspvcProfileDSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in DS side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.6 |
tlspvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.7 |
tlspvcProfileUSThe value of this object identifies the row in the atmProfileTable,
which applies for this pvc in US side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.11.1.1.8 |
ipbpvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.12 |
ipbpvcDomainTableThis table includes ipbpvc domain configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcDomainEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.1 |
ipbpvcDomainEntryAn entry of ipbpvcDomainTable. IpbpvcDomainEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1 |
ipbpvcDomainNameName of the domain.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.1 |
ipbpvcDomainRowStatusRow status of the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.12.1.1.2 |
ipbpvcDomainVlanTableThis table includes ipbpvc domain VLAN configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcDomainVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.2 |
ipbpvcDomainVlanEntryAn entry of ipbpvcDomainVlanTable. IpbpvcDomainVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1 |
ipbpvcDomainVlanIdSet VLAN to join or leave the specified domain.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.1 |
ipbpvcDomainDhcpVlanEnableEnable/disable DHCP VLAN in a domain.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.2 |
ipbpvcDomainVlanRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.12.2.1.3 |
ipbpvcEdgeRouterTableThis table includes ipbpvc edge router configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcEdgeRouterEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.3 |
ipbpvcEdgeRouterEntryAn entry of ipbpvcEdgeRouterTable. IpbpvcEdgeRouterEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1 |
ipbpvcEdgeRouterIpIP address of the edge router.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.1 |
ipbpvcEdgeRouterVidVLAN ID of the edge router.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.2 |
ipbpvcEdgeRouterMaskNetmask of the edge router.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.3 |
ipbpvcEdgeRouterRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.12.3.1.4 |
ipbpvcInterfaceTableThis table includes ipbpvc interface configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcInterfaceEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.4 |
ipbpvcInterfaceEntryAn entry of ipbpvcInterfaceTable. IpbpvcInterfaceEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1 |
ipbpvcInterfaceIpIP address of the interface.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.1 |
ipbpvcInterfaceMaskNetmask of the interface.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.2 |
ipbpvcInterfaceVidVLAN ID of the interface.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.3 |
ipbpvcInterfaceIfIndexIfIndex of the interface.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.4 |
ipbpvcInterfaceVpiVPI of the interface.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.5 |
ipbpvcInterfaceVciVCI of the interface.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.6 |
ipbpvcInterfaceRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.12.4.1.7 |
ipbpvcRouteTableThis table includes ipbpvc route configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcRouteEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.5 |
ipbpvcRouteEntryAn entry of ipbpvcRouteTable. IpbpvcRouteEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1 |
ipbpvcRouteIpIP address of the route.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.1 |
ipbpvcRouteMaskNetmask of the route.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.2 |
ipbpvcRouteNextHopNext hop IP address of the route.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.3 |
ipbpvcRouteMetricMetric of the route.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.4 |
ipbpvcRoutePriorityPriority of the route. Note that the default value of this object is 8, which means
we keep the original priority of the packet(frame).rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.5 |
ipbpvcRouteRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.12.5.1.6 |
ipbpvcTableThis table includes ipbpvc configuration.
This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.6 |
ipbpvcEntryAn entry of ipbpvcTable. IpbpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1 |
ipbpvcVpiVPI of the PVC.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.1 |
ipbpvcVciVCI of the PVC.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.2 |
ipbpvcPvidPVID of the PVC.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.3 |
ipbpvcEncapType of the PVC.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.4 |
ipbpvcPriorityPriority of the PVC.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.5 |
ipbpvcProfileProfile of the PVC.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.6 |
ipbpvcRowStatusRow status of the table used to create/delete an entry.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.7 |
ipbpvcProfileUSUS Profile of the PVC.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.12.6.1.8 |
arpproxy OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.12.8 |
arpproxyAgeAging time of the ARP proxy.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.1 |
arpproxyFlush OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2 |
arpproxyFlushTargetThe target whose ARP table to be flushed.
This object is supported by R3.00 and later versions.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.1 |
arpproxyFlushOpsSet the object to 1 to start flushing.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.2 |
arpproxyFlushEdgeRouterIpFlush ARP table for the specified edge router.
This object is supported by R3.00 and later versions.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.3 |
arpproxyFlushEdgeRouterVidFlush ARP table for the specified edge router.
This object is supported by R3.00 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.4 |
arpproxyFlushInterfaceIpFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.5 |
arpproxyFlushInterfaceMaskFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.6 |
arpproxyFlushInterfaceVidFlush ARP table for the specified interface.
This object is supported by R3.00 and later versions.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.12.8.2.7 |
dtpvc OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.14 |
dtpvcTableThis table includes Double Tagging (DT) PVC configuration. SEQUENCE OF DtpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.14.1 |
dtpvcEntryAn entry of dtpvcTable. DtpvcEntry .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1 |
dtpvcVpiVPI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.1 |
dtpvcVciVCI of the pvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.2 |
dtpvcSvids-tag VLAN ID of the pvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.3 |
dtpvcSprioritys-tag priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.4 |
dtpvcCvidc-tag VLAN ID of the pvc.rw VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.5 |
dtpvcCpriorityc-tag priority of the pvc.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.6 |
dtpvcDSProfileThe value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in DS side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.7 |
dtpvcUSProfileThe value of this object identifies the row in the atmProfileTable, which applies for this dtpvc in US side.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.8 |
dtpvcRowStatusThis object is used to create a new row or delete an existing row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.9 |
dtpvcSuperChannelSpecified the configured DTPVC is a super channel.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.10 |
dtpvcAcNameAccess concentrator name for paepvc.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.11 |
dtpvcServiceNameService name for paepvc.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.12 |
dtpvcHelloTimeThe system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.rw INTEGER UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.8.14.1.1.13 |
dtpvcStateTableThis table show current DTPVC status. SEQUENCE OF DtpvcStateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.14.2 |
dtpvcStateEntryAn entry in dtpvcStateTable. DtpvcStateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1 |
dtpvcStateVpiVPI of the dtpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.1 |
dtpvcStateVciVCI of the dtpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.2 |
dtpvcStateSvidDefault S-VID of the dtpvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.3 |
dtpvcStateSPriorityS-priority of the dtpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.4 |
dtpvcStateCvidDefault C-VID of the dtpvc.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.5 |
dtpvcStateCPriorityC-priority of the dtpvc.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.6 |
dtpvcStateChannelTypeThe value of this object identifies the channel type at runtime.ro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.8 |
dtpvcStateEncapThe value of this object identifies the channel encapsulation at runtime.ro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.8.14.2.1.9 |
snrMgn OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.15 |
snrMgnTableA table containing the per port SNR Margin configuration. SEQUENCE OF SnrMarginEntry .1.3.6.1.4.1.6321.1.2.3.1.8.15.1 |
snrMgnEntryAn entry of snrMgnTable. SnrMarginEntry .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1 |
snrMgnModeConfigure DSL SNR margin configuration mode of the specified ports.
Profile: the SNR margin configuration comes from DSL profile.
Line: the SNR margin configuration comes from line configuration.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.1 |
snrMgnUcTargetConfigured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.2 |
snrMgnUcMaxConfigured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.3 |
snrMgnUcMinConfigured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to
re-initialize or shut down.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.4 |
snrMgnUcDownshiftConfigured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate. In
the case that RADSL mode is not present,
the value will be `0'.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.5 |
snrMgnUcUpshiftConfigured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate. In
the case that RADSL is not present, the value will
be `0'.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.6 |
snrMgnUrTargetConfigured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.7 |
snrMgnUrMaxConfigured Maximum acceptable Signal/Noise Margin.
If the Noise Margin is above this the modem should
attempt to reduce its power output to optimize its
operation.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.8 |
snrMgnUrMinConfigured Minimum acceptable Signal/Noise Margin.
If the noise margin falls below this level, the modem
should attempt to increase its power output. If that
is not possible the modem will attempt to
re-initialize or shut down.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.9 |
snrMgnUrDownshiftConfigured Signal/Noise Margin for rate downshift.
If the noise margin falls below this level, the modem
should attempt to decrease its transmit rate.
In the case that RADSL mode is not present,
the value will be `0'.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.10 |
snrMgnUrUpshiftConfigured Signal/Noise Margin for rate upshift.
If the noise margin rises above this level, the modem
should attempt to increase its transmit rate.
In the case that RADSL is not present,
the value will be `0'.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.15.1.1.11 |
dslRate OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.16 |
dslRateTableA table containing the per port DSL Rate configuration. SEQUENCE OF DslRateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.16.1 |
dslRateEntryAn entry of dslRateTable. DslRateEntry .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1 |
dslRateModeConfigure DSL Rate configuration mode of the specified ports.
Profile: the DSL Rate configuration comes from DSL profile.
Line: the DSL Rate configuration comes from line configuration.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.1 |
dslRateLatencyModeThe latency mode is fast or interleavero Enumeration .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.2 |
dslRateXtucMaxInterleaveDelayConfigured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latency.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.3 |
dslRateXtucMaxTxRateConfigured Maximum Transmit rate for `Fast' or `Interleave' channels,
in bps.rw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.4 |
dslRateXtucMinTxRateConfigured Minimum Transmit rate for `Fast' or `Interleave' channels,
in bpsrw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.5 |
dslRateXturMaxInterleaveDelayConfigured maximum Interleave Delay for this channel.
Interleave delay applies only to the interleave channel
and defines the mapping (relative spacing) between
subsequent input bytes at the interleaver input and
their placement in the bit stream at the interleaver
output. Larger numbers provide greater separation
between consecutive input bytes in the output bit
stream allowing for improved impulse noise immunity
at the expense of payload latencyrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.6 |
dslRateXturMaxTxRateConfigured Target Signal/Noise Margin.
This is the Noise Margin the modem must achieve
with a BER of 10-7 or better to successfully complete
initialization.rw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.7 |
dslRateXturMinTxRateConfigured Maximum Transmit rate for `Fast' or `Interleave' channels,
in bps.rw Unsigned32 UNITS "kbps" .1.3.6.1.4.1.6321.1.2.3.1.8.16.1.1.8 |
gbond OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.8.51 |
gbondGroupTableA table containing the G.Bond configuration information for
each bonding group of the device. SEQUENCE OF GbondGroupEntry .1.3.6.1.4.1.6321.1.2.3.1.8.51.1 |
gbondGroupEntryAn entry of gbondTable. GbondGroupEntry .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1 |
gbondGroupNameAn administratively assigned string, which may be used to identify bonding group.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.1 |
gbondGroupPortsThe set of ports which are currently assigned to the
bonding group of specified group name.
Byte 1: Reserved(chassis)
Byte 2~3: Reserved(slot)
Byte 4: Reserved
Byte 5~11:each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.2 |
gbondGroupUpRateThe UP stream rate.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.4 |
gbondGroupDownRateThe DOWN stream rate.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.5 |
gbondGroupRowStatusThis object indicates the status of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.8.51.1.1.6 |
switch OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10 |
dscp OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.10 |
dscpMappingTableThe table contains DSCP mapping configuration for the adsl and ethernet ports. SEQUENCE OF DscpMappingEntry .1.3.6.1.4.1.6321.1.2.3.1.10.10.1 |
dscpMappingEntryAn entry of dscpMappingTable. DscpMappingEntry .1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1 |
dscpSrcCodePointThe DSCP source code point used for mapping.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.1 |
dscpMapPriorityThe mapping p bits that will replace the source p bits in the incoming packet.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.10.1.1.3 |
dscpPortTableThe table contains DSCP mapping configuration for the adsl and ethernet ports. SEQUENCE OF DscpPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.10.2 |
dscpPortEntryAn entry of dscpPortTable. DscpPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1 |
dscpStatusEnableThe DSCP port status.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.10.2.1.1 |
vlanIsolation OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.12 |
vlanIsolationTableA table contains configuration of isolated VLAN. SEQUENCE OF VlanIsolationEntry .1.3.6.1.4.1.6321.1.2.3.1.10.12.1 |
vlanIsolationEntryAn entry of vlanIsolationTable. VlanIsolationEntry .1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1 |
vlanIsolationRowStatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.12.1.1.1 |
enetMtu OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.13 |
enetMtuEntrySets the MTU size for layer 2 frame, size from 1526 to 1532, default value is 1526.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.13.1 |
dhcp OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.51 |
dhcpRelay82TableA table that contains DHCP Relay configuration. SEQUENCE OF DhcpRelay82Entry .1.3.6.1.4.1.6321.1.2.3.1.10.51.2 |
dhcpRelay82EntryThe entry of DHCP Relay table. DhcpRelay82Entry .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1 |
dhcpRelay82PrimaryServerThe IP address of the DHCP Relay primary server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.1 |
dhcpRelay82SecondaryServerThe IP address of the DHCP Relay secondary server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.2 |
dhcpRelay82ActiveServerThe current active DHCP Relay server.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.3 |
dhcpRelay82EnableEnable/disable DHCP relay and Option82 function.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.4 |
dhcpRelay82InfoUser specific Option82 information.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.5 |
dhcpRelay82RelayModeDHCP relay mode.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.6 |
dhcpRelay82Suboption2EnableEnable/disable Option 82 sub-option 2.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.8 |
dhcpRelay82Suboption2InfoUser specified information for Option 82 sub-option 2.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.9 |
dhcpRelay82EntryEnableEnable/disable DHCP Relayrw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.10 |
dhcpRelay82EntryOptionModeOption82 format.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.11 |
dhcpRelay82VlanIpThe IP address of the DHCP Relay interface for this VLAN.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.12 |
dhcpRelay82VlanMaskThe network mask of the DHCP Relay interface for this VLAN.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.13 |
dhcpRelay82VlanGatewayThe gateway of the DHCP Relay interface for this VLAN.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.14 |
dhcpRelay82ThirdServerThe IP address of the DHCP Relay third server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.15 |
dhcpRelay82FourthServerThe IP address of the DHCP Relay fourth server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.16 |
dhcpRelay82FifthServerThe IP address of the DHCP Relay fifth server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.17 |
dhcpRelay82ServerVidThe VID of the DHCP Relay server for this VLAN.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.2.1.18 |
dhcpRelayTest OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.51.8 |
dhcpRelayTestVidSetting the VID of the test server.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.8.1 |
dhcpRelayTestIpSetting the IP of the test server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.8.2 |
dhcpRelayTestOpsSet the object to 1 to test DHCP server.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.8.3 |
dhcpRelayTestStatusDisplay testing server status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.51.8.4 |
dhcpRelayArp OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.51.9 |
dhcpRelayArpShowTableThe table displays DHCP ARP. SEQUENCE OF DhcpRelayArpShowEntry .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1 |
dhcpRelayArpShowEntryAn entry of dhcpRelayArpShowTable. DhcpRelayArpShowEntry .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1 |
dhcpRelayArpShowVidDisplay the VID of the DHCP ARP entry.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.1 |
dhcpRelayArpShowIpDisplay the IP of the DHCP ARP entry.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.2 |
dhcpRelayArpShowMacDisplay the MAC of the DHCP ARP entry.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.1.1.3 |
dhcpRelayArpFlushOpsSet the object to 1 to start flushing.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.51.9.2 |
macfilter OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.53 |
macFilterPortTableThis table includes the status of mac filtering for each port. SEQUENCE OF MacFilterPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.1 |
macFilterPortEntryAn entry in macFilterPortTable. MacFilterPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1 |
macFilterPortEnableEnable/disable MAC filtering for the port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.1 |
macFilterPortMacCountThe total number of MAC addresses allowed for the port.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.2 |
macFilterPortFilterModeThe mac filter mode (accept or deny) for the port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.1.1.3 |
maxNumOfMacFiltersInSystemThe max number of mac filters supported in the system.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.2 |
maxNumOfMacFiltersPerPortThe max number of mac filters supported per port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.3 |
currNumOfMacFiltersInSystemThe current number of mac filters in the system.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.4 |
macFilterTableA table that contains the mac filter addresses. SEQUENCE OF MacFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.5 |
macFilterEntryThe entry of macFilterTable. MacFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1 |
macFilterAddrThe mac address which can pass through or be rejected from the port.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.1 |
macFilterRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.53.5.1.2 |
macfilterBatchSet OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.53.6 |
macfilterTargetThis managed object is used for identify the target on which
the port configuration should be performed. The target is encoded as:
Byte 1: 0, Reserved(chassis)
Byte 2~3: 0, Reserved(slot)
Byte 4: 0, reserved
Byte 5~11:each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.10.53.6.1 |
macfilterOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: enable mac filter
BIT 2: enable mac count filter
BIT 3: disable mac filter
BIT 4: set mac count
BIT 5: disable mac count filter.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.6.2 |
macFilterMacCountForBatchSetThe total number of MAC addresses allowed for a port.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.6.3 |
ouiFilterTableOldA table that contains the OUI filter addresses. SEQUENCE OF OuiFilterEntryOld .1.3.6.1.4.1.6321.1.2.3.1.10.53.7 |
ouiFilterEntryOldThe entry of ouiFilterTableOld. OuiFilterEntryOld .1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1 |
ouiFilterAddrOldThe first three bytes of the mac address which can pass through or be rejected from the port.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.1 |
ouiFilterRowStatusOldThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.53.7.1.2 |
maxNumOfOuiFiltersPerPortThe max number of OUI filters supported per port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.8 |
ouiFilterPortTableThis table includes the status of oui filtering for each port. SEQUENCE OF OuiFilterPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.9 |
ouiFilterPortEntryAn entry in macFilterPortTable. OuiFilterPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1 |
ouiFilterPortEnableEnable/disable oui filtering for the port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.1 |
ouiFilterPortFilterModeThe oui filter mode (accept or deny) for the port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.9.1.2 |
maxNumOfOuiFiltersInSystemThe max number of OUI filters supported in system.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.10 |
maxNumOfOuiFiltersPerVlanThe max number of OUI filters supported per vlan.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.53.11 |
ouiFilterTableA table that contains the OUI filter addresses. SEQUENCE OF OuiFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.12 |
ouiFilterEntryThe entry of ouiFilterTable. OuiFilterEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1 |
ouiFilterAddrThe first three bytes of the mac address which can pass through or be rejected from the vlan.ro OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.1 |
ouiFilterRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.53.12.1.2 |
ouiFilterVlanTableThis table includes the status of oui filtering for each configured VLAN. SEQUENCE OF OuiFilterVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.13 |
ouiFilterVlanEntryAn entry in ouiFilterVlanTable. OuiFilterVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1 |
ouiFilterVlanEnableEnable/disable oui filtering for the VLAN.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.1 |
ouiFilterVlanFilterModeThe oui filter mode (accept or deny) for the VLAN.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.53.13.1.2 |
dhcpSnoop OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.55 |
dhcpSnoopPortTableThis table includes DHCP snooping enable/disable for each port. SEQUENCE OF DhcpSnoopPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.55.1 |
dhcpSnoopPortEntryAn entry of dhcpSnoopPortTable. DhcpSnoopPortEntry .1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1 |
dhcpSnoopEnableEnable/disable DHCP snooping for a port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.1 |
dhcpSnoopMaxcntSet the max entries of the DHCP ARP table.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.2 |
dhcpSnoopSmacverifyEnableEnable/disable DHCP source MAC verify for a port.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.55.1.1.3 |
dhcpSnoopTargetThis managed object is used for identify the target on which
the operation should be performed. The target is encoded as:
Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7
Byte 2~3: each octet specifies a set of eight slots, with the
first octet specifying slots 1 through 8 and the second
octet specifying slots 9 through 16.
Byte 4: reserved
Byte 5~11:each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.10.55.2 |
dhcpSnoopOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: DHCP snooping table flush.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.55.3 |
dhcpStaticTableThis table defines DHCP static IP addresses. SEQUENCE OF DhcpStaticEntry .1.3.6.1.4.1.6321.1.2.3.1.10.55.4 |
dhcpStaticEntryAn entry of dhcpStaticTable. DhcpStaticEntry .1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1 |
dhcpStaticIpAddrThe IP address which can pass through the port.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.1 |
dhcpStaticRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.55.4.1.2 |
maxNumOfDhcpStaticIpThe maximum number of DHCP static IP addresses which can be created for a port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.55.5 |
dhcpSnoopMaxcntModeWhen DHCP snooping table is full, new DHCP lease will replace first one in option 0 or will be dropped in option 1.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.55.6 |
acl OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.56 |
aclSetTableaclsetTable. SEQUENCE OF AclSetEntry .1.3.6.1.4.1.6321.1.2.3.1.10.56.1 |
aclSetEntryAn entry of aclSetTable. AclSetEntry .1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1 |
aclSetVpiVPI valuero INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.1 |
aclSetVciVCI valuero INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.2 |
aclSetProfileNameACL Profile namero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.3 |
aclSetRowStatusRowStatus of aclSetEntryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.1.1.4 |
aclProfileTableaclProfileTable. SEQUENCE OF AclProfileEntry .1.3.6.1.4.1.6321.1.2.3.1.10.56.2 |
aclProfileEntryAn entry of aclProfileTable. AclProfileEntry .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1 |
aclProfileRuleNameProfile rule namero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.1 |
aclProfileRuleNumberThe managed object is for acl profile rule configuration.
etype <etype> vlan <vid> (1),
etype <etype> smac <mac> (2),
etype <etype> dmac <mac> (3),
vlan <vid> smac <mac> (4),
vlan <vid> dmac <mac> (5),
smac <mac> dmac <mac> (6),
vlan <vid> priority <priority> (7),
etype <etype> (8),
vlan <vid> (9),
smac <mac> (10),
dmac <mac> (11),
priority <priority> (12),
protocol <protocol> (13),
{srcip <ip>/<mask>{|dstip <ip>/<mask>{|tos <stos> <etos>{|srcport <sport> <eport> {|dstport <sport> <eport>}}}}} (14)rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.2 |
aclProfileActionNumberProfile action number.
Bit 1: rate
Bit 2: rvlan
Bit 3: rpri
Bit 4: deny
Bit 1, Bit 2 & Bit 3 can multiple selection.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.3 |
aclProfileRuleParamMaskProfile rule parameter mask.
BIT 1: srcip <ip>/<mask>
BIT 2: dstip <ip>/<mask>
BIT 3: tos <stos> <etos>
BIT 4: srcport <sport> <eport>
BIT 5: dstport <sport> <eport>rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.4 |
aclProfileRuleEtypeProfile rule etyperw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.5 |
aclProfileRuleVidProfile rule vidrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.6 |
aclProfileRuleSmacProfile rule source MACrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.7 |
aclProfileRuleDmacProfile rule destination MACrw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.8 |
aclProfileRulePriorityProfile rule priorityrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.9 |
aclProfileRuleProtocolProfile rule protocol.
icmp(1),igmp(2),ip(4),tcp(6),
udp(17),gre(47),ospf(89),
other ptyperw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.10 |
aclProfileRuleSrcIPProfile rule source IPrw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.11 |
aclProfileRuleSrcIPMaskThe subnet mask of source IP maskrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.12 |
aclProfileRuleDestIPProfile rule source IPrw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.13 |
aclProfileRuleDestIPMaskThe subnet mask of dest IP maskrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.14 |
aclProfileRuleStartTosProfile rule start type of servicerw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.15 |
aclProfileRuleEndTosProfile rule end type of servicerw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.16 |
aclProfileRuleSrcStartPortProfile rule source start portrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.17 |
aclProfileRuleSrcEndPortProfile rule source end portrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.18 |
aclProfileRuleDestStartPortProfile rule destination start portrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.19 |
aclProfileRuleDestEndPortProfile rule destination end portrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.20 |
aclProfileActionRateProfile action to replace to this raterw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.21 |
aclProfileActionrvlanProfile action to replace to this vlanrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.22 |
aclProfileActionrpriProfile action to replace to this priorityrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.23 |
aclProfileRowStatusThe row status of the entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.56.2.1.24 |
pppoeAgent OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.57 |
pppoeAgentTableA table that contains PPPoE DHCP Relay configuration. SEQUENCE OF PppoeAgentEntry .1.3.6.1.4.1.6321.1.2.3.1.10.57.1 |
pppoeAgentEntryAn entry of pppoeAgentTable. PppoeAgentEntry .1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1 |
pppoeAgentEnableEnable/disable DHCP relay and Option82 function.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.1 |
pppoeAgentInfoUser specific Option82 information.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.2 |
pppoeAgentRowStatusRow status of the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.3 |
pppoeAgentOptionModeOption82 format.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.57.1.1.4 |
maxNumOfPppoeDhcpRelay82ConfThe maximum number of rows that can be created in pppoeAgentTable.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.57.2 |
macff OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.10.60 |
macFfTableA table that contains MAC Force Forwarding configuration. SEQUENCE OF MacFfEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.1 |
macFfEntryAn entry of macFfTable. MacFfEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1 |
macFfIndexIndex of the MACFF.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.1 |
macFfVidThe VLAN-ID refering to this AR/AS.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.2 |
macFfArIPIP of this AR/ASrw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.3 |
macFfSrcIPThe source IP address of the MACFF.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.4 |
macFfSrcMaskThe subnet mask of source IP mask.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.5 |
macFfRowStatusThe row status of the MacFfEntry entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.60.1.1.6 |
macFfArpFlushSet the object to 1 to flush mac table.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.3 |
maxNumOfMacFfVlanInSystemThe max number of macff Vlans supported in the system.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.4 |
macFfVlanTableA table that contains MAC Force Forwarding Vlan configuration. SEQUENCE OF MacFfVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.5 |
macFfVlanEntryAn entry of macFfVlanTable. MacFfVlanEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1 |
macFfVlanRowstatusRow status of the table used to create/delete an entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.1 |
macFfVlanUnknownUnicastSetting downstream unknown uni-cast packet on macff vlan to flooding or dropping.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.10.60.5.1.2 |
macFfStaticIPTable SEQUENCE OF MacFfStaticIPEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.6 |
macFfStaticIPEntryAn entry of macFfTable. MacFfStaticIPEntry .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1 |
macFfStaticIPPortThe port number, 1 ~ 48.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.1 |
macFfStaticIPVidVLAN ID of the IP range, 1 ~ 4094, the vid should be enable the MACFF function first.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.2 |
macFfstaticIPThe specified IP range.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.3 |
macFfStaticIPMaskMask_bits is 24 .. 32.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.4 |
macFfStaticIPRowStatusThe row status used to configure the table entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.10.60.6.1.5 |
sys OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11 |
accessCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.5 |
securedClientTableA table that contains information about secured clients. SEQUENCE OF SecuredClientEntry .1.3.6.1.4.1.6321.1.2.3.1.11.5.2 |
securedClientEntryA list of secured client entry. SecuredClientEntry .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1 |
securedClientIndexThe index of the entry.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.1 |
securedClientStartIpThe starting IP address of the secured client set.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.2 |
securedClientEndIpThe ending IP address of the secured client set.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.3 |
securedClientServiceEach bit corresponds to a service. The bit is set to 1 if the
service is enabled, and set to 0 if the service is disabled.
The various bit positions are:
BIT 1: telnet
BIT 2: ftp
BIT 3: web
BIT 4: icmp
BIT 5: not support
BIT 6: snmp.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.4 |
securedClientEnableEnable/disable the entry.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.5.2.1.5 |
extAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.8 |
extAlarmTableA table that contains external alarm information. SEQUENCE OF ExtAlarmEntry .1.3.6.1.4.1.6321.1.2.3.1.11.8.1 |
extAlarmEntryThe entry of external alarm table. ExtAlarmEntry .1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1 |
extAlarmIndexThe index of the entry.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.1 |
extAlarmnameThe external alarm name.rw DisplayString .1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.2 |
extAlarmstatusDispaly 'Normal' or 'Alarm' stringro DisplayString .1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.3 |
extAlarmTriggeredModeThe external alarm triggered mode.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.8.1.1.4 |
user OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.9 |
userAuthModeUser authentication procsssing mode.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.9.1 |
userAuthServerIpThe IP address of the authentication server.rw IpAddress .1.3.6.1.4.1.6321.1.2.3.1.11.9.2 |
userAuthServerPortThe port of the authentication server.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.11.9.3 |
userAuthServerSecretThe secret between the authentication server and the NE for authentication process.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.11.9.4 |
userTableA table that contains user information. SEQUENCE OF UserEntry .1.3.6.1.4.1.6321.1.2.3.1.11.9.5 |
userEntryAn entry of userTable. UserEntry .1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1 |
userNameThe user name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.1 |
userPasswordThe user password.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.2 |
userPriviledgeThe user priviledge to decide what operation the user can and cannot do.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.3 |
userRowStatusThe row status used to create or delete a user.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.11.9.5.1.4 |
userAuthDefaultPriviledgeThe user default priviledge to be assigned when radius authentication succeds
but no user priviledge information(radius service-type) is provided.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.9.6 |
usbCastCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.10 |
usBcastCtrlEnableEnable/disable upstream broadcast control.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.10.1 |
usBcastCtrlRate32~49984 in step of 32kbpsrw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.11.10.2 |
dsbCastCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.11 |
dsBcastCtrlEnableEnable/disable downstream broadcast control.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.11.1 |
dsBcastCtrlRate32~1000000 in step of 32 kbpsrw INTEGER UNITS "Kbps" .1.3.6.1.4.1.6321.1.2.3.1.11.11.2 |
stdioTimeoutSet the CLI/TELNET/WEB Session timeout, 0, or 1~300 minutes, 0 => disable.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.11.12 |
isConfigChangedIf system configuration has been changed.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.13 |
fwUpgrade OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.14 |
fwUpgradeVersionConfigure the target firmware version that will be upgraded.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.11.14.1 |
fwUpgradeCheckEnable/disable firmware upgrade version checking feature.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.14.2 |
fwUpgradeStatusDisplay current firmware upgrade status.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.11.14.3 |
delayedReboot OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.11.15 |
delayedRebootTimer5~1800 secs, 0: reboot immediately.rw INTEGER UNITS "sec" .1.3.6.1.4.1.6321.1.2.3.1.11.15.1 |
delayedRebootRemainingTimeDisplay the remaining time of scheduled reboot.ro INTEGER UNITS "sec" .1.3.6.1.4.1.6321.1.2.3.1.11.15.2 |
delayedRebootCancelcancel the scheduled reboot.rw Enumeration .1.3.6.1.4.1.6321.1.2.3.1.11.15.3 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.12 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13 |
igmpQueryCntTotalThe total number of IGMP query messages received.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.1 |
igmpReportCntTotalThe total number of IGMP report messages received.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.2 |
igmpLeaveCntTotalThe total number of IGMP leave messages received.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.3 |
igmpNumOfActiveGroupsThe total number of IGMP learned groups.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.4 |
igmpGroupTableThis table includes igmp group information. SEQUENCE OF IgmpGroupEntry .1.3.6.1.4.1.6321.1.2.3.1.13.5 |
igmpGroupEntryAn entry in igmpGroupTable. IgmpGroupEntry .1.3.6.1.4.1.6321.1.2.3.1.13.5.1 |
igmpGroupIpigmp group IPro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.5.1.1 |
igmpGroupvidvlan idro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.5.1.2 |
igmpGroupnumberOfMembersnumber Of Membersro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.5.1.3 |
igmpGroupMemberPortsGroup Member Portsro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.5.1.4 |
igmpGroupPortTableThis table includes igmp Group port information. SEQUENCE OF IgmpGroupPortEntry .1.3.6.1.4.1.6321.1.2.3.1.13.6 |
igmpGroupPortEntryAn entry in igmpGroupPortTable. IgmpGroupPortEntry .1.3.6.1.4.1.6321.1.2.3.1.13.6.1 |
igmpGroupPortIpIgmp Group IPro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.6.1.1 |
igmpGroupPortvidIgmp Group vidro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.6.1.2 |
igmpGroupV2TableA table that displays IGMP learned group member information. SEQUENCE OF IgmpGroupV2Entry .1.3.6.1.4.1.6321.1.2.3.1.13.7 |
igmpGroupV2EntryAn entry of igmpGroupV2Table. IgmpGroupV2Entry .1.3.6.1.4.1.6321.1.2.3.1.13.7.1 |
igmpGroupV2VidThe IGMP group VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.7.1.1 |
igmpGroupV2IpThe multicast IP address.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.7.1.2 |
igmpGroupV2NumOfMembersThe number of member ports in the group.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.7.1.3 |
igmpGroupV2MemberPortsThe member port list of the group.ro PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.7.1.4 |
igmpGroupPortV2TableA table that displays IGMP joined groups in this port. SEQUENCE OF IgmpGroupPortV2Entry .1.3.6.1.4.1.6321.1.2.3.1.13.8 |
igmpGroupPortV2EntryAn entry of igmpGroupPortV2Table. IgmpGroupPortV2Entry .1.3.6.1.4.1.6321.1.2.3.1.13.8.1 |
igmpGroupPortV2VidThe IGMP group VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.8.1.1 |
igmpGroupPortV2IpThe multicast IP address.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.8.1.2 |
igmpGroupPortV2SourceIpThe source IP address that joins the IGMP group.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.8.1.3 |
igmpPortCtrlPduTableA table that displays IGMP related counter values in this port. SEQUENCE OF IgmpPortCtrlPduEntry .1.3.6.1.4.1.6321.1.2.3.1.13.9 |
igmpPortCtrlPduEntryAn entry of igmpPortCtrlPduTable. IgmpPortCtrlPduEntry .1.3.6.1.4.1.6321.1.2.3.1.13.9.1 |
igmpPortCtrlPduQueryCntThe total number of IGMP query messages received in this port.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.9.1.1 |
igmpPortCtrlPduReportCntThe total number of IGMP report messages received in this port.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.9.1.2 |
igmpPortCtrlPduLeaveCntThe total number of IGMP leave messages received in this port.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.9.1.3 |
igmpPortNumOfActiveGroupsThe total number of active IGMP groups in this port.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.9.1.4 |
igmpPortCtrlAuditLeaveCntThe total number of groups left by audit query.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.9.1.5 |
dhcpStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.11 |
dhcpSnoopIpTableThis table shows the IP addresses and netmasks offered by the DHCP server. SEQUENCE OF DhcpSnoopIpEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.1 |
dhcpSnoopIpEntryAn entry of dhcpSnoopIpTable. DhcpSnoopIpEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1 |
dhcpSnoopIpThe snooped IP address.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.1 |
dhcpSnoopMacThe snooped MAC address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.2 |
dhcpSnoopVidThe snooped VLAN ID.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.3 |
dhcpSnoopMaskThe snooped IP maskro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.4 |
dhcpSnoopGatewayThe snooped Gateway.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.5 |
dhcpSnoopRouteMapThe refrence bit map of the dhcp routero OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.13.11.1.1.6 |
dhcpSnoopCounterTableThis table shows the DHCP statistics. SEQUENCE OF DhcpSnoopCounterEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.2 |
dhcpSnoopCounterEntryAn entry of dhcpSnoopCounterTable. DhcpSnoopCounterEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1 |
dhcpDiscoveryThe total number of received DHCP server discovery packets.ro Counter64 .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.1 |
dhcpOfferThe total number of received DHCP server offer packets.ro Counter64 .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.2 |
dhcpRequestThe total number of received DHCP IP request packets.ro Counter64 .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.3 |
dhcpAckThe total number of received DHCP IP acknowledge packets.ro Counter64 .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.4 |
dhcpAckBySnoopFullThe total number of received DHCP IP acknowledge packets that replace the oldest snooping
entry in snooping table due to table full.ro Counter64 .1.3.6.1.4.1.6321.1.2.3.1.13.11.2.1.5 |
dhcpRouteTableA table that contains dhcp route information. SEQUENCE OF DhcpRouteEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.3 |
dhcpRouteEntryAn entry of dhcpRouteTable. DhcpRouteEntry .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1 |
dhcpRouteIndexro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.1 |
dhcpRouteVidThe VLAN-ID refering to this dhcp route.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.2 |
dhcpRouteIPIP of this dhcp routero IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.3 |
dhcpRouteMaskThe subnet mask of source IP mask.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.4 |
dhcpRouteGwIPThe gateway IP address.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.11.3.1.5 |
paepvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.12 |
paepvcSessionTableThis table shows the paepvc session statistics. SEQUENCE OF PaepvcSessionEntry .1.3.6.1.4.1.6321.1.2.3.1.13.12.1 |
paepvcSessionEntryAn entry of paepvcSessionTable. PaepvcSessionEntry .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1 |
paepvcSessionVpiThe PAEPVC VPI.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.1 |
paepvcSessionVciThe PAEPVC VCI.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.2 |
paepvcSessionStateThe PAEPVC status.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.3 |
paepvcSessionIdThe PAEPVC session ID.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.4 |
paepvcSessionUptimeThe PAEPVC session uptime.ro Unsigned32 UNITS "second" .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.5 |
paepvcSessionacnameAccess concentrator name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.6 |
paepvcSessionsrvcnameService name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.12.1.1.7 |
paepvcCountTableThis table shows the paepvc counters. SEQUENCE OF PaepvcCountEntry .1.3.6.1.4.1.6321.1.2.3.1.13.12.2 |
paepvcCountEntryAn entry of paepvcCountTable. PaepvcCountEntry .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1 |
paepvcCountVpiThe PAEPVC VPI.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.1 |
paepvcCountVciThe PAEPVC VCI.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.2 |
paepvcCountPppLcpCfgReqRxThe number of ppp lcp config-request received.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.3 |
paepvcCountPppLcpEchoReqRxThe number of ppp lcp echo-request received.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.4 |
paepvcCountPppLcpEchoReplyRxThe number of ppp lcp echo-reply received.ro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.5 |
paepvcCountPadiTxThe number of pppoe padi transferedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.6 |
paepvcCountPadoRxThe number of pppoe pado receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.7 |
paepvcCountPadrTxThe number of pppoe padr transferedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.8 |
paepvcCountPadsRxThe number of pppoe pads receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.9 |
paepvcCountPadtTxThe number of pppoe padt transferedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.10 |
paepvcCountPadtRxThe number of pppoe padt receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.11 |
paepvcCountSrvcnameErrRxThe number of pppoe service name error receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.12 |
paepvcCountAcSystemErrRxThe number of pppoe access concentrator name error receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.13 |
paepvcCountGenericErrTxThe number of pppoe generic error transferedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.14 |
paepvcCountGenericErrRxThe number of pppoe generic error receivedro Unsigned32 .1.3.6.1.4.1.6321.1.2.3.1.13.12.2.1.15 |
macStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.13 |
macDisplayTargetThis managed object is a filter used for identify the target from which
the MAC addresses are learned in macTable. The target could be:
99: all ports in the system
98: all subscriber ports
97: all Ethernet ports
IfIndex is used for identifying subscriber ports and Ethernet Ports(e.g. 1 ~ 50).rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.13.1 |
macTableA table that contains information about unicast
entries for which the bridge has forwarding and/or
filtering information. This information is used
by the transparent bridging function in
determining how to propagate a received frame. SEQUENCE OF MacEntry .1.3.6.1.4.1.6321.1.2.3.1.13.13.2 |
macEntryAn entry of macTable. MacEntry .1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1 |
macAddressA unicast MAC address for which the bridge has
forwarding and/or filtering information.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.1 |
macPortThe port from which the mac address has been learned.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.2 |
macStatusThe status of this entry.ro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.13.13.2.1.3 |
ipbpvcStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.14 |
arpproxyTableDisplay ARP table. This table is supported by R3.00 and later versions. SEQUENCE OF ArpproxyEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.1 |
arpproxyEntryAn entry of arpproxyTable. ArpproxyEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1 |
arpproxyIpro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.1 |
arpproxyMacro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.2 |
arpproxyIfIndexro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.3 |
arpproxyVpiro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.4 |
arpproxyVciro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.5 |
arpproxyInterfaceIpro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.6 |
arpproxyInterfaceMaskro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.7 |
arpproxyInterfaceVidro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.8 |
arpproxyDhcpIpro Enumeration .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.9 |
arpproxyTypero Enumeration .1.3.6.1.4.1.6321.1.2.3.1.13.14.1.1.10 |
ipbpvcIfDynamicTableDisplay runtime interfaces. This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcIfDynamicEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.2 |
ipbpvcIfDynamicEntryAn entry of ipbpvcIfDynamicTable. IpbpvcIfDynamicEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1 |
ipbpvcIfDynamicIpro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.1 |
ipbpvcIfDynamicMaskro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.2 |
ipbpvcIfDynamicIfIndexro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.3 |
ipbpvcIfDynamicVpiro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.4 |
ipbpvcIfDynamicVciro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.2.1.5 |
ipbpvcRouteDynamicTableDisplay runtime routing table. This table is supported by R3.00 and later versions. SEQUENCE OF IpbpvcRouteDynamicEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.3 |
ipbpvcRouteDynamicEntryAn entry of ipbpvcRouteDynamicTable. IpbpvcRouteDynamicEntry .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1 |
ipbpvcRouteDynamicTypero Enumeration .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.1 |
ipbpvcRouteDynamicIpro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.2 |
ipbpvcRouteDynamicMaskro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.3 |
ipbpvcRouteDynamicNextHopro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.4 |
ipbpvcRouteDynamicMetricro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.5 |
ipbpvcRouteDynamicPriorityro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.14.3.1.6 |
macffStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.16 |
macFfStatsTableA table that contains MAC Force Forwarding static configuration and dynamic information. SEQUENCE OF MacFfStatsEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.1 |
macFfStatsEntryAn entry of macFfStatsTable. MacFfStatsEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1 |
macFfStatsIndexIndex of the MACFF.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.1 |
macFfStatsVidThe VLAN-ID refering to this AR/AS.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.2 |
macFfStatsArIPIP of this AR/ASro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.3 |
macFfStatsSrcIPThe source IP address of the MACFF.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.4 |
macFfStatsSrcMaskThe subnet mask of source IP mask.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.16.1.1.5 |
macFfArpTableA table that contains MAC Force Forwarding ARP information. SEQUENCE OF MacFfArpEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.2 |
macFfArpEntryAn entry of macFfArpTable. MacFfArpEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1 |
macFfArpVidThe VLAN-ID refering to this AR/AS.ro VlanIndex (Q-BRIDGE-MIB) .1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.1 |
macFfArpIPIP of this AR/AS.ro IpAddress .1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.2 |
macFfArpPortPort of this AR/AS.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.3 |
macFfArpMacMAC address of the AR or AS.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.6321.1.2.3.1.13.16.2.1.4 |
macFfArpCounterTableA table that contains MAC Force Forwarding ARP counter information. SEQUENCE OF MacFfArpCounterEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.3 |
macFfArpCounterEntryAn entry of macFfArpCounterTable. MacFfArpCounterEntry .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1 |
macFfArpCounterRequestTXARP Request TX counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.1 |
macFfArpCounterRequestRXARP Request RX counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.2 |
macFfArpCounterRequestRXDropARP Request RX drop counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.3 |
macFfArpCounterReplyTXARP Reply TX counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.4 |
macFfArpCounterReplyRXARP Reply RX counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.5 |
macFfArpCounterReplyRXDropARP Reply RX drop counter.ro Counter32 .1.3.6.1.4.1.6321.1.2.3.1.13.16.3.1.6 |
enetStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.17 |
enetSfpInfoTableThis table includes sfp info of enet port. SEQUENCE OF EnetSfpInfoEntry .1.3.6.1.4.1.6321.1.2.3.1.13.17.2 |
enetSfpInfoEntryAn entry in enetSfpInfoTable. EnetSfpInfoEntry .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1 |
enetSfpInfoTxpowerMeasured Tx Output Power.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.1 |
enetSfpInfoRxpowerMeasured Rx Output Power.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.2 |
enetSfpInfoTemperatureMeasured temperature.ro INTEGER (-1280000..1280000) UNITS "10^-4 C" .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.3 |
enetSfpInfoTxBiasMeasured tx bias.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.4 |
enetSfpInfoVoltageMeasured voltage.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.17.2.1.5 |
adslStats OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.13.18 |
adslPortUtilTableThis table includes adsl port utilization. SEQUENCE OF AdslPortUtilEntry .1.3.6.1.4.1.6321.1.2.3.1.13.18.1 |
adslPortUtilEntryAn entry in adslPortUtilEntry. AdslPortUtilEntry .1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1 |
adslPortUtilTxMeasure adsl port's tx utilization.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.1 |
adslPortUtilRxMeasure adsl port's rx utilization.ro INTEGER .1.3.6.1.4.1.6321.1.2.3.1.13.18.1.1.2 |
clear OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.14 |
counterClearTargetThis managed object is used for identify the target on which
the counter would be cleared. The target is encoded as:
Byte 1: reserved
Byte 2~3: reserved
Byte 4: reserved
Byte 5~11:each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.rw OCTET STRING .1.3.6.1.4.1.6321.1.2.3.1.14.1 |
counterClearOpsThe corresponding bit is set to 1 to start the operation.
The various bit positions are:
BIT 1: clear interface counters
BIT 2: clear pvc packet counters
BIT 3: clear port ATM counters
BIT 4: clear pvc ATM counters
BIT 5: clear DHCP counters
BIT 6: clear IGMP counters
BIT 7: clear IGMP port counters
BIT 8: clear MACFF ARP counters
BIT 9: clear current lineperf
BIT 10: clear current 15 minute lineperf
BIT 11: clear current 1 day lineperfrw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.14.2 |
counterClearVpiVPI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.14.3 |
counterClearVciVCI of the pvc whose counters would be cleared.rw INTEGER .1.3.6.1.4.1.6321.1.2.3.1.14.4 |
aesSeriesCommon OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.97 |
iesSeriesCommon OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.98 |
accessSwitchCommonATM OBJECT IDENTIFIER .1.3.6.1.4.1.6321.1.2.3.1.99 |