Dell-POLICY-MIB
The private MIB module definition generic traffic policy in Dell devices.
Main OID:
rlPolicy.1.3.6.1.4.1.89.59
355
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
355 total| Object Name |
|---|
rlPolicyThe private MIB module definition generic traffic policy in Dell devices. MODULE-IDENTITY .1.3.6.1.4.1.89.59 |
IMPORTSInterface type. Enumeration .1.3.6.1.4.1.89.59 |
rlPolicyMibVersionMIB's version, the current version is 14
1 - original version
2 - two new fields
rlPolicyActionChangeDscpNonConform
rlPolicyActionNewDscpNonConform
were added.
3 - added support new policy features
QoS modes: basic and advanced
support for trusted mode operations
mapping tables for trusted ports
dscp, tcpUdp, mutation, remarking.
4 - I) added support to service mode.
II)DSCP to VPT mapping table
III) download marker
5 - Added cos-Dscp to RlPolicyTrustTypes
6 - Added rlPolicyFlowClassificationOffsetsGroupUseVPTId and
rlPolicyFlowClassificationOffsetsGroupUseEtherTypeId To
rlPolicyFlowClassificationOffsetsTable
Added rlPolicyClassifierVPTID And
rlPolicyClassifierEtherTypeID To
rlPolicyClassifierTable
Added Vpt and Ethertype support to rlPolicyClassifierAdditionalCriteriaSupported
7 - Added rlPolicyPortCfgPortRateLimitStatus,rlPolicyPortCfgCirPortRateLimit
rlPolicyPortCfgCbsPortRateLimit to rlPolicyPortConfigurationTable
8 - Added rlPolicyDefaultForwardingProtocol to rlPolicyDefaultForwardingTable
Added rlPolicyDscpToDpTable
9 - Add statistics
10 - Add classifier utilization
11 -Added rlPolicyFlowClassificationOffsetsGroupUseInnerVlanId To
rlPolicyFlowClassificationOffsetsTable
Added rlPolicyClassifierInnerVID To
rlPolicyClassifierTable
Added Inner vlan id support to rlPolicyClassifierAdditionalCriteriaSupported
12 - Added rlPolicyVlanConfigurationTable
13 - Added rlPolicyIsTCAvailable scalar
14 - Added rlPolicyCPUSafeGuardEnablero INTEGER .1.3.6.1.4.1.89.59.1 |
rlPolicyClassifier OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.2 |
rlPolicyClassifierPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.2.1 |
rlPolicyFlowClassificationOffsetsGroupSchemeSome platforms allow Policy statements to examine all packet
offsets(Opal); other platforms require specification of specific
byte offsets for routedIp packets, another set of offsets for
routedIpx, a third set for bridge.ro Enumeration .1.3.6.1.4.1.89.59.2.1.1 |
rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroupFor platforms which require an FCOG, indicates the maximum
number of byte offsets specifiable for each offset group.roobsolete INTEGER .1.3.6.1.4.1.89.59.2.1.2 |
rlPolicyFlowClassificationOffsetGroupMaximumOffsetIndicates the maximum value of a byte offset in a
Flow Classification Offset Group. If 0, there is no limit.ro INTEGER .1.3.6.1.4.1.89.59.2.1.3 |
rlPolicyNumberOfOffsetsPerOmpcGroupindicates the maximum number of byte offsets
specifiable for each Ompc offset group.ro INTEGER .1.3.6.1.4.1.89.59.2.1.4 |
rlPolicyOmpcMaximumOffsetIndicates the maximum value of a byte offset in a
Ompc Group. If 0, there is no limit.ro INTEGER .1.3.6.1.4.1.89.59.2.1.5 |
rlPolicyOMPCPermittedOperatorsA bit mask indicating which operators are permissable in an OMPC:
|87654321|
1 - equal operator permitted
2 - not-equal operator permitted
3 - greater-than operator permitted
4 - less-than operator permittedro OCTET STRING .1.3.6.1.4.1.89.59.2.1.6 |
rlPolicyMaxOMPCLengthForBiggerSmallerOperationIndicates the maximal permissible length of an OMPC using
bigger' or 'smaller' condition. If 0, there is no limit.ro INTEGER .1.3.6.1.4.1.89.59.2.1.7 |
rlPolicyClassifierAdditionalCriteriaSupportedA bit mask indicating which additional Criteria may be supported
by the classifier:
|87654321|
1 - input port supported
2 - output port supported
3 - VLAN ID for bridging supported
4 - VPT ID for bridging supported
5 - EtherType ID for bridging supported
6 - Inner VLAN ID for bridging supportedroobsolete OCTET STRING .1.3.6.1.4.1.89.59.2.1.8 |
rlPolicyClassifierAdditionalCriteriaUsedInOffsetCountIndicates whether the additional FCOG or Classifier criteria
(ie. inPort, outPort VID count towards the maximum number of offsets
ie. whether using inPort in the FCOG reduces the maximum number of
offsets available.roobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.1.9 |
rlPolicyClassifierPermittedOffsetTypesA bit mask indicating which offset types are supported by the
platform for FCOG and OMPC definitions:
|87654321|
1 - L2 offsets supported
2 - L3 offsets supportedroobsolete OCTET STRING .1.3.6.1.4.1.89.59.2.1.10 |
rlPolicyClassifierOMPCActionsA bit mask indicating which operation could be performed with OPMC
|87654321|
1 - equal,
2 - notEqual,
3 - bigger,
4 - smaller.ro OCTET STRING .1.3.6.1.4.1.89.59.2.1.11 |
rlPolicyFlowClassificationOffsetsTableSpecifies the byte offsets that the platform can use for
policy decisions. This table is used for platforms
which impose limitations on choosing the OMPCs for classification.
If the platform does not impose any limitations, the value of
rlPolicyFlowClassificationOffsetsGroupScheme is allOffsetsPermitted.
Each entry in the table specifies a combination of byte offsets
which can be used to specify flow classification. A rule may
use a subset of the bytes of its Offset Group.
The maximum value for each offset is given by
rlPolicyFlowClassificationOffsetGroupMaximumOffset.
The maximum number of offsets per Offset Group is given by
rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup. SEQUENCE OF RlPolicyFlowClassificationOffsetsGroupEntry .1.3.6.1.4.1.89.59.2.2 |
rlPolicyFlowClassificationOffsetsGroupEntryThe flow classification offset table entry includes the
following parameters RlPolicyFlowClassificationOffsetsGroupEntry .1.3.6.1.4.1.89.59.2.2.1 |
rlPolicyFlowClassificationOffsetsGroupTypeSpecifies a classifier type for which offset bytes can be specified.ro RlPolicyGroupType .1.3.6.1.4.1.89.59.2.2.1.1 |
rlPolicyFlowClassificationOffsetsGroupOffsetThe list of offsets to be included in the Flow Classification Offset
Group are specified as subidentifiers in the OID(after the first 2
bytes which must be 1.1). The maximal number of permissible offsets
is given by rlPolicyNumberOfOffsetsPerFlowClassificationOffsetGroup.
The maximal value that an offset can have is
rlPolicyFlowClassificationOffsetGroupMaximumOffset.rw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.2.2.1.2 |
rlPolicyFlowClassificationOffsetsGroupOffsetTypeIndicates whether the corresponding byte denotes an offset from beginning
of L2, from the beginning of L3 IPv4 packet data or from the beginning
of L3 IPv6 packet data.
Each byte in the OID contains either:
(1) - L2 offset
(2) - L3 Offset
(3) - L3 IPv6 Offsetrw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.2.2.1.3 |
rlPolicyFlowClassificationOffsetsGroupMaskThe list of masks corresponding to the offsets to be included in the
Flow Classification Offset Group are specified as bytes in the
OID(after the first 2 bytes which must be 1.1).rw OCTET STRING .1.3.6.1.4.1.89.59.2.2.1.4 |
rlPolicyFlowClassificationOffsetsGroupUseInputInterfaceIndicates whether or not the Input Interface Index is usable
in Policy Rule definitions.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.5 |
rlPolicyFlowClassificationOffsetsGroupUseOutputInterfaceIndicates whether or not the Output Interface Index(ie.
routing/bridging decision) is usable in Policy Rule definitionsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.6 |
rlPolicyFlowClassificationOffsetsGroupUseVlanIdIndicates whether or not the VlanId is usable in Policy Rule
definitions for bridged packetsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.7 |
rlPolicyFlowClassificationOffsetsGroupStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.8 |
rlPolicyFlowClassificationOffsetsGroupUseVPTIdIndicates whether or not the VPT is usable in Policy Rule
definitions for bridged packetsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.9 |
rlPolicyFlowClassificationOffsetsGroupUseEtherTypeIdIndicates whether or not the EtherType is usable in Policy Rule
definitions for bridged packetsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.10 |
rlPolicyFlowClassificationOffsetsGroupUseInnerVlanIdIndicates whether or not the inner VlanId is usable in Policy Rule
definitions for bridged packetsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.2.1.11 |
rlPolicyOMPCTableThe table of OMPC statements. SEQUENCE OF RlPolicyOMPCEntry .1.3.6.1.4.1.89.59.2.3 |
rlPolicyOMPCEntryEach classification statement consists of the following parameters RlPolicyOMPCEntry .1.3.6.1.4.1.89.59.2.3.1 |
rlPolicyOMPCGroupTypeSpecifies a classifier type for which offset bytes can be specified.ro RlPolicyGroupType .1.3.6.1.4.1.89.59.2.3.1.1 |
rlPolicyOMPCIndexIndex into the OMPC Table.ro INTEGER .1.3.6.1.4.1.89.59.2.3.1.2 |
rlPolicyOMPCOffsetSpecifies the offset within the frame (in bytes) from the layer
according to rlPolicyGroupType. The limitation of this field is
according to the rlPolicyFlowClassificationOffsetGroupMaximumOffset
parameter if this OMPC is used by an entry in the
rlPolicyClassifierTable whose rlPolicyClassifierType is a protocol
for which predefined offsets in rlPolicyFlowClassificationOffsetsTable
are required.
rlPolicyRequiredOffsetGroups indicates for which protocols there is
such a requirement.rw INTEGER .1.3.6.1.4.1.89.59.2.3.1.3 |
rlPolicyOMPCOffsetTypeIndicates whether the offset should be interpreted as relative to the
beginning of L2 or the beginning of L3rw Enumeration .1.3.6.1.4.1.89.59.2.3.1.4 |
rlPolicyOMPCMaskSpecifies which bits of the rlPolicyOMPCPattern field are
significant for packet comparison. The length of the mask,
in case of 'bigger' or 'smaller' rlPolicyOMPCCondition,
is limited by rlPolicyMaxOMPCLengthForBiggerSmallerOperation.rw OCTET STRING .1.3.6.1.4.1.89.59.2.3.1.5 |
rlPolicyOMPCPatternDescribes the mask field. The length of this object must be equal
to the length of rlPolicyOMPCMask.rw OCTET STRING .1.3.6.1.4.1.89.59.2.3.1.6 |
rlPolicyOMPCConditionThese define the operation carried out on the two 'operands'
(frame and pattern), i.e. Bigger means that frame bits should be
bigger than pattern bits. The permitted values are according to
rlPolicyOMPCPermittedOperators parameter, if this OMPC is used by
an entry in the rlPolicyClassifierTable whose rlPolicyClassifierType
is a protocol for which predefined offsets in
rlPolicyFlowClassificationOffsetsTable are required.
rlPolicyRequiredOffsetGroups indicates for which protocols there is
such a requirement.rw Enumeration .1.3.6.1.4.1.89.59.2.3.1.7 |
rlPolicyOMPCDescriptionFree text specifing the nature of this OMPC.rw DisplayString .1.3.6.1.4.1.89.59.2.3.1.8 |
rlPolicyOMPCStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.3.1.9 |
rlPolicyClassifierTableThe table of Classifier statement. SEQUENCE OF RlPolicyClassifierEntry .1.3.6.1.4.1.89.59.2.4 |
rlPolicyClassifierEntryClassifiers can be of the ingress, egress, or post-routing phase
varieties.
Each multifield classification statement consists of the
following parameters. RlPolicyClassifierEntry .1.3.6.1.4.1.89.59.2.4.1 |
rlPolicyClassifierTypeSpecifies a classifier type for which offset bytes can be specified.ro RlPolicyGroupType .1.3.6.1.4.1.89.59.2.4.1.1 |
rlPolicyClassifierListIndexList Index into the Classifier Table.ro INTEGER .1.3.6.1.4.1.89.59.2.4.1.2 |
rlPolicyClassifierSubListIndexSubList Index into the Classifier Table.ro INTEGER .1.3.6.1.4.1.89.59.2.4.1.3 |
rlPolicyClassifierIndexIndex into the Classifier Table.ro INTEGER .1.3.6.1.4.1.89.59.2.4.1.4 |
rlPolicyClassifierOmpcListThe list of OMPCs to check with this Classifier. Each
subidentifier together with rlPolicyClassifierType specify one OMPC.rw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.2.4.1.5 |
rlPolicyClassifierInIfIndexInput interface index to be compared with received packet,
a value of 0 denotes that the classifier is applied to all ports.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.59.2.4.1.6 |
rlPolicyClassifierOutIfIndexOutput interface index to be compared with sent packet,
a value of 0 denotes that the classifier is applied to all ports.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.59.2.4.1.7 |
rlPolicyClassifierVIDVLAN ID, used only for bridged traffic.rw INTEGER .1.3.6.1.4.1.89.59.2.4.1.8 |
rlPolicyClassifierDiffservInIfTypeFor a classifier used by the Diffserv Rules table. Enables
specification of a classifier that should apply to all
Diffserv boundary ports or all Diffserv Interior ports.
If normal is specified, the rlPolicyClassifierInIfIndex field
is used as it is in the non-diffserv case. If allBoundary or
allInterior is selected, rlPolicyClassifierInIfIndex is ignoredrw RlPolicyClassifierDiffservIfType .1.3.6.1.4.1.89.59.2.4.1.9 |
rlPolicyClassifierDiffservOutIfTypeFor a classifier used by the Diffserv Rules table. Enables
specification of a classifier that should apply to outbound
traffic on all Diffserv boundary ports or all Diffserv Interior
ports.
If normal is specified, the rlPolicyClassifierOutIfIndex field
is used as it is in the non-diffserv case. If allBoundary or
allInterior is selected, rlPolicyClassifierOutIfIndex is ignoredrw RlPolicyClassifierDiffservIfType .1.3.6.1.4.1.89.59.2.4.1.10 |
rlPolicyClassifierStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.2.4.1.11 |
rlPolicyClassifierInIfIndexListallow to define list of ports for the specific classifier
for ingress classification. if rlPolicyClassifierInIfIndex equal to zero
then the following list should be reffered , if the list is empty we refer
to ALL Portsrw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.59.2.4.1.12 |
rlPolicyClassifierOutIfIndexListallow to define list of ports for the specific classifier
for egress classification. if rlPolicyClassifierOutIfIndex equal to zero
then the following list should be reffered , if the list is empty we refer
to ALL Portsrw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.59.2.4.1.13 |
rlPolicyClassifierVPTIDVPT ID - user priority tag to be compared with .
8 is used to indicate not used value for this classifierrw INTEGER .1.3.6.1.4.1.89.59.2.4.1.14 |
rlPolicyClassifierVPTIDMaskVPT ID Mask ,mask the user priority field .
0 is the default indicate Mask all compared with any VPT valuerw INTEGER .1.3.6.1.4.1.89.59.2.4.1.15 |
rlPolicyClassifierEtherTypeIDEtherType ID, to be compared with.
65535 is used to indicate not used value for this classifier
1499 is uded to indicate IPv4 ethertype that is originated from IPv4 ACL with permit/deny any any any
1500 is uded to indicate IPv6 ethertype that is originated from IPv6 ACL with permit/deny any any anyrw INTEGER .1.3.6.1.4.1.89.59.2.4.1.16 |
rlPolicyClassifierInnerVIDINNER VLAN ID, used only for double tagged traffic.rw INTEGER .1.3.6.1.4.1.89.59.2.4.1.17 |
rlPolicyRules OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.3 |
rlPolicyRulesPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.3.1 |
rlPolicyDroppedPacketCountSupportedIndicates whether the dropped packets counter in the
rlPolicyRulesTable is supported.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.3.1.1 |
rlPolicyFilterActionOptionsA bit mask indicating which operation could be perform
|87654321|
1 - block,
2 - blockAndTrap,
3 - permitAndTrap,
4 - permit.ro OCTET STRING .1.3.6.1.4.1.89.59.3.1.2 |
rlPolicyIngressMeteringSupportedSpecifies whether the platform supports metering in inbound packet
rules.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.3.1.3 |
rlPolicyEgressMeteringSupportedSpecifies whether the platform supports metering on outbound packet
rules (for Diffserv).ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.3.1.4 |
rlPolicyRulesTableThe table of rules and Rules statements applied to all incoming traffic
at the post-routing phase - ie. both the inPort and outPort are
available for classification
When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option
for Diffserv is off), certain table parameters are not available(see
below). The DiffServ option is enabled or disabled by setting
rlDiffservModeEnabled. SEQUENCE OF RlPolicyRulesEntry .1.3.6.1.4.1.89.59.3.2 |
rlPolicyRulesEntryEach multifield classification statement consists of the following
parameters. RlPolicyRulesEntry .1.3.6.1.4.1.89.59.3.2.1 |
rlPolicyRulesTableTypeSpecifies a classifier type for which offset bytes can be specified.ro RlPolicyGroupType .1.3.6.1.4.1.89.59.3.2.1.1 |
rlPolicyRulesInterfaceDirectionSpecifies the direction for this entry on the
interface. 'inbound' traffic is operated on during
receipt, while 'outbound' traffic is operated on prior
to transmission.
Based on the metering support:
inbound available while the ingress metering supported,
outbound available while egress metering supported,
and none while no metering supported.ro Enumeration .1.3.6.1.4.1.89.59.3.2.1.2 |
rlPolicyRulesListIndexEnumerates the rule list entry.ro INTEGER .1.3.6.1.4.1.89.59.3.2.1.3 |
rlPolicyRulesSubListIndexEnumerates the rule sub-list entry.ro INTEGER .1.3.6.1.4.1.89.59.3.2.1.4 |
rlPolicyRulesIndexEnumerates the rule index entry.ro INTEGER .1.3.6.1.4.1.89.59.3.2.1.5 |
rlPolicyRulesFilteringActionSpecifies the action for the filter.
Values 1-10 reserved for the System filtering implemetation;
Values starting from 11 may be used for user definition about
future application.rw Enumeration .1.3.6.1.4.1.89.59.3.2.1.6 |
rlPolicyRulesDroppedPacketsThe number of packets blocked by this filtering rule.ro Counter32 .1.3.6.1.4.1.89.59.3.2.1.7 |
rlPolicyRulesFurtherRefPointerThis further reference indicate on the entry at the metering or
action table, based on the supported features. The
rlPolicyRulesFurtherRefPointer points on the metering table if the
metering feature is supported, if not this fields points on the
Action tablerw INTEGER .1.3.6.1.4.1.89.59.3.2.1.8 |
rlPolicyRulesDescriptionFree text specifing the nature of this Rule.rw DisplayString .1.3.6.1.4.1.89.59.3.2.1.9 |
rlPolicyRulesStatusRow status of the Rules entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.3.2.1.10 |
rlPolicyRulesCounterIdxIf not zero, perform counting of matched packets .rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.11 |
rlPolicyRulesCounterThe number of packets that matched this filtering rule.ro Counter32 .1.3.6.1.4.1.89.59.3.2.1.12 |
rlPolicyRulesActionPointerThis further reference indicate on the entry at the
action table, The rlPolicyRulesActionPointer points on the action
table if the aggregate metering feature is supported,or
if meter is not belong to data path.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.13 |
rlPolicyRulesTimeRange1Time range of the first ACL.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.14 |
rlPolicyRulesTimeRange2Time range of the second ACL.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.15 |
rlPolicyRulesSrcPortRangeStartStart port of port range for source port.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.16 |
rlPolicyRulesSrcPortRangeEndEnd port of port range for source port.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.17 |
rlPolicyRulesDestPortRangeStartStart port of port range for destination port.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.18 |
rlPolicyRulesDestPortRangeEndEnd port of port range for destination port.rw INTEGER .1.3.6.1.4.1.89.59.3.2.1.19 |
rlPolicyRulesActionDropTypeThis field is valid only if rlPolicyRulesFilteringAction is
not permit. Used to distinguish between Hard and Soft drop.rw RlPolicyRulesActionDropType .1.3.6.1.4.1.89.59.3.2.1.20 |
rlPolicyRulesDownloadMarkerIndicates when rules download or removing starts and terminates.rw Enumeration .1.3.6.1.4.1.89.59.3.3 |
rlPolicyMeterClass OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.4 |
rlPolicyMeterPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.4.1 |
rlPolicyMeterDepthIndicates how many meters can be chained in succession (ie. so
that if the first meter fails, the second can be examined).
The final meter in a sequence is always 'always-conform', so if
the value of this parameter is 2, the platform that supports a
single meter and then a second marking/action for meter failure.ro INTEGER .1.3.6.1.4.1.89.59.4.1.1 |
rlPolicyMeterClassTableThis table defines the Metering classes for the system. SEQUENCE OF RlPolicyMeteringClassEntry .1.3.6.1.4.1.89.59.4.2 |
rlPolicyMeteringClassEntryEach statement consists of the following parameters RlPolicyMeteringClassEntry .1.3.6.1.4.1.89.59.4.2.1 |
rlPolicyMeteringClassIndexThis enumerates the table entry.ro INTEGER .1.3.6.1.4.1.89.59.4.2.1.1 |
rlPolicyMeteringClassAlwaysConformIf true, the meter always accepts all traffic; its
rate is effectively infinite. In such a case, the token
bucket defined by the MeterRate and Burst-Size
parameters is ignored.
also used when there isn't metering support.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.4.2.1.2 |
rlPolicyMeteringClassAggregateMeterRateThe rate in kilobytes/second of traffic considered within the
bandwidth allocated for this policy entry.rw INTEGER UNITS "kbps" .1.3.6.1.4.1.89.59.4.2.1.3 |
rlPolicyMeteringClassAggregateMeterBurstSizeThe Burst Size parameter for the aggregate meter leaky bucket. A
value of 0 means that the device should choose the Burst Size
that it thinks is most suitable for the rule.
The interval can be derived from (burstSizex8/Rate).rw INTEGER UNITS "bytes" .1.3.6.1.4.1.89.59.4.2.1.4 |
rlPolicyMeteringClassPerSessionMeteringRateA Quantitative Appliction policy rule where each individual
session requires a guaranteed minimum bandwidth.
Specifies the Ingress traffic flow meter per session
indicate a bandwidth limit to be applied to each individual session
Value 0 at rlPolicyMeteringClassPerSessionMetering
and rlPolicyMeteringClassMaxSessionLimit
is interpreted to mean no sepecific requarment and
the aggregate metering will be done by the system decision.
The rate in kilobytes/secondrw INTEGER UNITS "kbps" .1.3.6.1.4.1.89.59.4.2.1.5 |
rlPolicyMeteringClassMaxSessionLimitindicate a the maximum number of session for a sepecific rule
to guarante minimum bandwidth.
Value 0 at rlPolicyMeteringClassPerSessionMetering
and rlPolicyMeteringClassMaxSessionLimit
is interpreted to mean no sepecific requarment and
the aggregate metering will be done by the system decision.rw INTEGER .1.3.6.1.4.1.89.59.4.2.1.6 |
rlPolicyMeteringClassActionPointerSpecifies the index in the rlPolicyActionTable to be
accessed for packets that are in-profile.
Value 0 is interpreted to mean no action.
A non-zero value may be specified only for RoutedIp
packets in Diffserv mode.rw INTEGER .1.3.6.1.4.1.89.59.4.2.1.7 |
rlPolicyMeteringClassFailMeterPointerSpecifies an index in the rlPolicyMeterClassTable. This
is the meter that is to be used if the packet is out-of-profile
relative to the current meter.
If non-Diffserv mode, this field is not used.
If the current meter is AlwaysConform, this field is not used.rw INTEGER .1.3.6.1.4.1.89.59.4.2.1.8 |
rlPolicyMeteringClassStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.4.2.1.9 |
rlPolicyMeteringCounterEnableEnable metering counter for the meter entry.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.4.2.1.10 |
rlPolicyMeteringClassInProfileCountermeter counter for packets that are in profile .ro Counter32 .1.3.6.1.4.1.89.59.4.2.1.11 |
rlPolicyMeteringClassOutProfileCountermeter counter for packets that are out of profilero Counter32 .1.3.6.1.4.1.89.59.4.2.1.12 |
rlPolicyAction OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.5 |
rlPolicyActionPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.5.1 |
rlPolicyActionMREDSupportedIndicates whether the platform supports setting MRED characteristics
in the packet actionro Enumeration .1.3.6.1.4.1.89.59.5.1.1 |
rlPolicyActionDroppedPacketCountSupportedIndicates whether the platform can maintain a count of
packets Marked for drop by a particular action.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.1.2 |
rlPolicyActionDroppedDropPrecedenceSupportedIndicates whether the platform support at drop precedence.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.1.3 |
rlPolicyActionInProfileDropPrecedenceA bit mask indicating which drop precedence supported
|87654321|
1 - low,
2 - medium,
3 - high,
4 - dropro OCTET STRING .1.3.6.1.4.1.89.59.5.1.4 |
rlPolicyActionOutProfileDropPrecedenceA bit mask indicating which drop precedence supported
|87654321|
1 - low,
2 - medium,
3 - high,
4 - dropro OCTET STRING .1.3.6.1.4.1.89.59.5.1.5 |
rlPolicyActionDscpSupportIndicates whether the platform support at DSCP filed modification.roobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.1.6 |
rlPolicyActionDsQueueManagmentSupportedIndicates whether the platform supports at Q managment for implementation,
mred, randomDrop used by the min/max thresholdroobsolete Enumeration .1.3.6.1.4.1.89.59.5.1.7 |
rlPolicyActionTableThis table defines the Actions for packets that pass the meter table
ie. the characteristics that are assigned to packets before they
reach the scheduler.
When Diffserv is not in effect(ie. IPX, bridging, or IP when the global option
for Diffserv is off), certain table parameters are not available(see
below). The DiffServ option is enabled or disabled by setting
rlDiffservModeEnabled. SEQUENCE OF RlPolicyActionEntry .1.3.6.1.4.1.89.59.5.2 |
rlPolicyActionEntryEach multifield classification statement consists of the following
parameters RlPolicyActionEntry .1.3.6.1.4.1.89.59.5.2.1 |
rlPolicyActionIndexThis enumerates the Action entry.ro INTEGER .1.3.6.1.4.1.89.59.5.2.1.1 |
rlPolicyActionNewDscpIndicates the new DSCP with which the packet should
be markedrw INTEGER .1.3.6.1.4.1.89.59.5.2.1.2 |
rlPolicyActionChangeDscpIf true, the packet is re-marked with the value indicated by
newDscp above. If false, the packet's DSCP value is not changedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.3 |
rlPolicyActionMinThresholdThe min-threshold is the queue depth that a random
drop process will seek to manage the queue's depth to.
This object is in the action table rather than the
queue table because Differentiated Services PHBs, such
as the Assured Service, permit differently classified
traffic to have different drop parameters even though
they occupy the same queue.rw INTEGER .1.3.6.1.4.1.89.59.5.2.1.4 |
rlPolicyActionMaxThresholdThe max-threshold is the maximum permissible queue
depth. In tail drop scenarios, the queue will drop if a
packet is presented to it and it is instantaneously
full by this measure. In random drop scenarios, the
queue will drop if a packet is presented to it and the
average queue depth exceeds the max-threshold.
This object is in the action table rather than the
queue table because Differentiated Services PHBs, such
as the Assured Service, permit differently classified
traffic to have different drop parameters even though
they occupy the same queue.rw INTEGER .1.3.6.1.4.1.89.59.5.2.1.5 |
rlPolicyActionDropPolicyrw Enumeration .1.3.6.1.4.1.89.59.5.2.1.6 |
rlPolicyActionDroppedPacketsThe number of packets dropped by this actionro Counter32 .1.3.6.1.4.1.89.59.5.2.1.7 |
rlPolicyActionNonDsInProfileDropPrecedenceThis paramer is used at non diffserv mode to attached the drop precedence
for packet InProfile (metering), only if there is a support for drop precedence
and with what level.rw Enumeration .1.3.6.1.4.1.89.59.5.2.1.8 |
rlPolicyActionNonDsOutProfileDropPrecedenceThis paramer is used at non diffserv mode to attached the drop precedence
for packet OutProfile (metering), only if there is a support for drop precedence
and with what level.rw Enumeration .1.3.6.1.4.1.89.59.5.2.1.9 |
rlPolicyActionChangeVptRouted packets that run through the Rules receive VPT as define at the
service class they attached to, bridge packets receive through the
802.1p operation unless we define to change the VPT for those packets.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.10 |
rlPolicyActionNewVptPriority Tag that will be written to packets .rw INTEGER (0 .. 7) .1.3.6.1.4.1.89.59.5.2.1.11 |
rlPolicyActionServiceClassPointerSpecifies the index in rlPolicyServiceClassTable denoting
the service class to which the packet should be assigned
after the action specified in this entry is carried out.
A value of 0 means that no Service class is assigned. A
value of 0 is legal only for routedIp packets in Diffserv
mode on Inbound processing.rw INTEGER .1.3.6.1.4.1.89.59.5.2.1.12 |
rlPolicyActionStatusThe status of the table entryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.13 |
rlPolicyActionChangeDscpNonConformIf true, the packet is re-marked with the value indicated by
newDscp for non conforming packets.
If false, the packet's DSCP value is not changedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.14 |
rlPolicyActionChangeNewDscpNonConformIndicates the new DSCP with which the packet should
be markedrw INTEGER .1.3.6.1.4.1.89.59.5.2.1.15 |
rlPolicyActionAdvancedTrustModeIndicates if egress queue is assigned for packets match
rule according to global trust mode or note.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.16 |
rlPolicyActionNewIpPrecedenceIndicates the new Ip- Precedence with which the packet should
be markedrw INTEGER .1.3.6.1.4.1.89.59.5.2.1.17 |
rlPolicyActionChangeIpPrecedenceIf true, the packet is re-marked with the value indicated by
newIpPrecedence above. If false, the packet's DSCP value is not changedrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.5.2.1.18 |
rlPolicyActionReDirectSpecified the redirection action/rw RlPolicyRedirectAction .1.3.6.1.4.1.89.59.5.2.1.19 |
rlPolicyActionNewInterfaceRelevant if rlQosClassMapRedirect is either
'redirectToInterface' or 'analyzerPort'.
Specified the output interface the packet is redireted to or
the port that gets copy of the packet in addition to the port
it was farwarded.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.59.5.2.1.20 |
rlPolicyActionChangeVidActionIf 'mark', than the classified
traffic will be remarked with new VLAN id.
If 'disabled' VLAN id is not changed.
If markNestedVlan, if the egress interface defined as
VLAN tagged member then a new VLAN tag is added to the packet.rw RlPolicyMarkVlanAction .1.3.6.1.4.1.89.59.5.2.1.21 |
rlPolicyActionNewVidIf rlPolicyActionChangeVid is true,
specify the new Vlan id to assigned to the packetrw INTEGER .1.3.6.1.4.1.89.59.5.2.1.22 |
rlPolicyActionTrapTypeIdIf now zero, Indicates the trap type id the matched packets arrives with,
relevant when RedirectAction is trap or mirror.rw INTEGER .1.3.6.1.4.1.89.59.5.2.1.23 |
rlPolicyActionAddTunnelIf not zero - Tunnel is added to matched packets.rw Unsigned32 .1.3.6.1.4.1.89.59.5.2.1.24 |
rlPolicyServiceClass OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6 |
rlPolicyServiceClassPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.1 |
rlPolicyNumberOfServiceClassesSupportedIndicates the number of service classes supported on each
port of the platform. Service classes can be neither
created nor destroyed.ro INTEGER .1.3.6.1.4.1.89.59.6.1.1 |
rlPolicyBoundedPriorityQueueSupportIndicates whether the platform supports setting an upper limit
to the bandwidth of traffic transmitted on queues operating in
Strict Priority mode.roobsolete Enumeration .1.3.6.1.4.1.89.59.6.1.2 |
rlPolicyDefaultServiceClassIndicates which service class is default one for packets whose COS is undetermined.rw INTEGER .1.3.6.1.4.1.89.59.6.2 |
rlPolicyActiveServiceClassTableSpecifies the Service Class table preform active action
(usuarlly after set of entries at the service class tentative table).
Specifies the current status of a table, there could be two options,
tentative/active table. only the tentative table is the read-write
and the active table is read-only. at set to activeAction the
tentative table will be copied to the active table.rw Enumeration .1.3.6.1.4.1.89.59.6.3 |
rlPolicyServiceClassTentativeTableThis table defines the service classes for the system ie. the queue
discipline and weight characteristics that are implemented on each
port unless the user configures a port specific value in ....
The total number of service classes defined can not exceed
rlPolicyNumberOfTransmitQueuesPerPort. SEQUENCE OF RlPolicyServiceClassTentativeEntry .1.3.6.1.4.1.89.59.6.4 |
rlPolicyServiceClassTentativeEntryEach multifield classification statement consists of the following
parameters RlPolicyServiceClassTentativeEntry .1.3.6.1.4.1.89.59.6.4.1 |
rlPolicyServiceClassTentativeIndexThis enumerates the ServiceClass Tentative entry.ro INTEGER .1.3.6.1.4.1.89.59.6.4.1.1 |
rlPolicyServiceClassTentativeNameThe name given by the system administrator to the class.rw DisplayString .1.3.6.1.4.1.89.59.6.4.1.2 |
rlPolicyServiceClassTentativePhbTypeIndicates the type of Diffserv per-hop behaviour that this service
class is intended to support. This object can be set by the user
only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled).rw Enumeration .1.3.6.1.4.1.89.59.6.4.1.3 |
rlPolicyServiceClassTentativeMinRateSpecifies either the minimum throughput of the queue as a percentage
of the throughput of each output port on which the service class is
implemented. If zero, there is no minimum rate. This field can not
be set by the user if rlDiffservModeEnabled = disabled and
rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled
and rlPolicyServiceClassPhbType = expeditedForwarding.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.4 |
rlPolicyServiceClassTentativeMaxRateSpecifies either the upper limit on the throughput of the queue as a
percentage of the throughput of each output port on which the service
class is implemented. If zero, there is no maximum rate.
This field can not be set by the user
if rlDiffservModeEnabled = disabled and
rlPolicyServiceClassPriority = 0 or
rlDiffservModeEnabled = enabled and
rlPolicyServiceClassPhbType != expeditedForwarding or
rlBoundedPriorityQueueSupport = notSupported.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.5 |
rlPolicyServiceClassTentativePriorityIf non-zero, this service class will operate as a priority service
class with the specified priority value. This object can not be set
in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case
rlServiceClassPhbType should be used instead. It can't be set when
rlBoundedPriorityQueueSupport = notSupported as well.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.6 |
rlPolicyServiceClassTentative8021DPri802.1D Priority Tag that will be written to routed packets and
untagged bridged packets transmitted with this service class.rw INTEGER (0 .. 7) .1.3.6.1.4.1.89.59.6.4.1.7 |
rlPolicyServiceClassTentativeStatusStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.4.1.8 |
rlPolicyServiceClassTentativeTdThersholdDp0Tail Drop Threshold for Drop Precedence 0.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.9 |
rlPolicyServiceClassTentativeTdThersholdDp1Tail Drop Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.10 |
rlPolicyServiceClassTentativeTdThersholdDp2Tail Drop Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.11 |
rlPolicyServiceClassTentativeRedMinDp0WRED Min Threshold for Drop Precedence 0.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.12 |
rlPolicyServiceClassTentativeRedMaxDp0WRED Max Threshold for Drop Precedence 0.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.13 |
rlPolicyServiceClassTentativeRedProbDp0WRED probability for Drop Precedence 0.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.14 |
rlPolicyServiceClassTentativeRedMinDp1WRED Min Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.15 |
rlPolicyServiceClassTentativeRedMaxDp1WRED Max Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.16 |
rlPolicyServiceClassTentativeRedProbDp1WRED probability for Drop Precedence 1.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.17 |
rlPolicyServiceClassTentativeRedMinDp2WRED Min Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.18 |
rlPolicyServiceClassTentativeRedMaxDp2WRED Max Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.19 |
rlPolicyServiceClassTentativeRedProbDp2WRED probability for Drop Precedence 2.rw INTEGER .1.3.6.1.4.1.89.59.6.4.1.20 |
rlPolicyServiceClassTentativeRedQweightadditional parameter for the WRED algorithem supporting
the Queue weight exponentail factorrw INTEGER .1.3.6.1.4.1.89.59.6.4.1.21 |
rlPolicyServiceClassTentativeShaperStatusIf there is shaper on the Queuerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.4.1.22 |
rlPolicyServiceClassTentativeCirQueueShaperThe CIR for the Queue shaper.
N/A when the shper is disabled.
UNITS bps bits per secondrw INTEGER .1.3.6.1.4.1.89.59.6.4.1.23 |
rlPolicyServiceClassTentativeCbsQueueShaperThe CBS for the Queue shaper.
N/A when the shper is disabled.
UNITS bytesrw INTEGER .1.3.6.1.4.1.89.59.6.4.1.24 |
rlPolicyServiceClassActiveTableThis table defines the service classes for the system ie. the queue
discipline and weight characteristics that are implemented on each
port unless the user configures a port specific value in ....
The total number of service classes defined can not exceed
rlPolicyNumberOfTransmitQueuesPerPort. SEQUENCE OF RlPolicyServiceClassActiveEntry .1.3.6.1.4.1.89.59.6.5 |
rlPolicyServiceClassActiveEntryEach multifield classification statement consists of the following
parameters RlPolicyServiceClassActiveEntry .1.3.6.1.4.1.89.59.6.5.1 |
rlPolicyServiceClassActiveIndexThis enumerates the ServiceClass Active entry.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.1 |
rlPolicyServiceClassActiveNameThe name given by the system administrator to the class.ro DisplayString .1.3.6.1.4.1.89.59.6.5.1.2 |
rlPolicyServiceClassActivePhbTypeIndicates the type of Diffserv per-hop behaviour that this service
class is intended to support. This object can be set by the user
only in DiffServ mode (i.e. rlDiffservModeEnabled = enabled).ro Enumeration .1.3.6.1.4.1.89.59.6.5.1.3 |
rlPolicyServiceClassActiveMinRateSpecifies either the minimum throughput of the queue as a percentage
of the throughput of each output port on which the service class is
implemented. If zero, there is no minimum rate. This field can not
be set by the user if rlDiffservModeEnabled = disabled and
rlPolicyServiceClassPriority > 0 or rlDiffservModeEnabled = enabled
and rlPolicyServiceClassPhbType = expeditedForwarding.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.4 |
rlPolicyServiceClassActiveMaxRateSpecifies either the upper limit on the throughput of the queue as a
percentage of the throughput of each output port on which the service
class is implemented. If zero, there is no maximum rate.
This field can not be set by the user
if rlDiffservModeEnabled = disabled and
rlPolicyServiceClassPriority = 0 or
rlDiffservModeEnabled = enabled and
rlPolicyServiceClassPhbType != expeditedForwarding or
rlBoundedPriorityQueueSupport = notSupported.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.5 |
rlPolicyServiceClassActivePriorityIf non-zero, this service class will operate as a priority service
class with the specified priority value. This object can not be set
in Diffserv mode (i.e. rlDiffservModeEnabled = enabled), in which case
rlServiceClassPhbType should be used instead. It can't be set when
rlBoundedPriorityQueueSupport = notSupported as well.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.6 |
rlPolicyServiceClassActive8021DPri802.1D Priority Tag that will be written to routed packets and
untagged bridged packets transmitted with this service class.ro INTEGER (0 .. 7) .1.3.6.1.4.1.89.59.6.5.1.7 |
rlPolicyServiceClassActiveTdThersholdDp0Tail Drop Threshold for Drop Precedence 0.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.8 |
rlPolicyServiceClassActiveTdThersholdDp1Tail Drop Threshold for Drop Precedence 1.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.9 |
rlPolicyServiceClassActiveTdThersholdDp2Tail Drop Threshold for Drop Precedence 2.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.10 |
rlPolicyServiceClassActiveRedMinDp0WRED Min Threshold for Drop Precedence 0.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.11 |
rlPolicyServiceClassActiveRedMaxDp0WRED Max Threshold for Drop Precedence 0.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.12 |
rlPolicyServiceClassActiveRedProbDp0WRED probability for Drop Precedence 0.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.13 |
rlPolicyServiceClassActiveRedMinDp1WRED Min Threshold for Drop Precedence 1.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.14 |
rlPolicyServiceClassActiveRedMaxDp1WRED Max Threshold for Drop Precedence 1.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.15 |
rlPolicyServiceClassActiveRedProbDp1WRED probability for Drop Precedence 1.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.16 |
rlPolicyServiceClassActiveRedMinDp2WRED Min Threshold for Drop Precedence 2.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.17 |
rlPolicyServiceClassActiveRedMaxDp2WRED Max Threshold for Drop Precedence 2.
UNITS percent 0-100ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.18 |
rlPolicyServiceClassActiveRedProbDp2WRED probability for Drop Precedence 2.ro INTEGER .1.3.6.1.4.1.89.59.6.5.1.19 |
rlPolicyServiceClassActiveRedQweightadditional parameter for the WRED algorithem supporting
the Queue weight exponentail factorro INTEGER .1.3.6.1.4.1.89.59.6.5.1.20 |
rlPolicyServiceClassActiveShaperStatusIf there is shaper on the Queuero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.5.1.21 |
rlPolicyServiceClassActiveCirQueueShaperThe CIR for the queue shaper.
N/A when the shper is disabled
UNITS bps bits per secondro INTEGER .1.3.6.1.4.1.89.59.6.5.1.22 |
rlPolicyServiceClassActiveCbsQueueShaperThe CBS for the queue shaper.
N/A when the shper is disabled.
UNITS bytesro INTEGER .1.3.6.1.4.1.89.59.6.5.1.23 |
rlPolicyPortConfigurationTableThis table enables the network administrator to fine-tune
the bandwidth given to each service class on each port.
The values in this table will thus override those of the
rlServiceClassTable (THIS TABLE IS MANAGE FROM 3SW). SEQUENCE OF RlPolicyPortCfgEntry .1.3.6.1.4.1.89.59.6.6 |
rlPolicyPortCfgEntryConfiguration parameters for each port/service class. RlPolicyPortCfgEntry .1.3.6.1.4.1.89.59.6.6.1 |
rlPolicyPortCfgIfIndexInterface index.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.59.6.6.1.1 |
rlPolicyPortCfgMinimalBandwidthThe list of objects contain parameters at Precents type for the minimal bandwidth
to this port/service class at WWR . The OID length is based on the number of the
service class number, every OID define parameter of service class.rw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.6.1.2 |
rlPolicyPortCfgMaximalBandwidthThe list of objects contain parameters at Precents type for the maximal bandwidth
to this port/service class at SP . The OID length is based on the number of the
service class number, every OID define parameter of service class.rw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.6.1.3 |
rlPolicyPortCfgStatusStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.6.1.4 |
rlpolicyDropProfilePointerpointing to drop algorithem profile.
the profile describs the drop algorithem
(tail, red)and paramsrw INTEGER .1.3.6.1.4.1.89.59.6.6.1.5 |
rlPolicyPortCfgQueueShaperStatusIf there is shaper on the Queuerw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.6.1.6 |
rlPolicyPortCfgCirQueueShaperThe CIR for the Queue shaper.
N/A when the shper is disabled
UNITS bps bits per secondrw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.6.1.7 |
rlPolicyPortCfgCbsQueueShaperThe CBS for the Queue shaper.
N/A when the shper is disabled.
UNITS bytesrw OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.6.6.1.8 |
rlPolicyPortCfgPortShaperStatusIf there is shaper on the portrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.6.1.9 |
rlPolicyPortCfgCirPortShaperThe CIR for the port shaper.
N/A when the shper is disabled
UNITS bps bits per secondrw INTEGER .1.3.6.1.4.1.89.59.6.6.1.10 |
rlPolicyPortCfgCbsPortShaperThe CBS for the port shaper.
N/A when the shper is disabled.
UNITS bytesrw INTEGER .1.3.6.1.4.1.89.59.6.6.1.11 |
rlPolicyPortCfgPortRateLimitStatusIf there is Rate Limit on the portrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.6.1.12 |
rlPolicyPortCfgCirPortRateLimitThe CIR for the port Rate limit.
N/A when the Rate limit is disabled
UNITS bps bits per secondrw INTEGER .1.3.6.1.4.1.89.59.6.6.1.13 |
rlPolicyPortCfgCbsPortRateLimitThe CBS for the port Rate Limit.
N/A when the Rate Limit is disabled.
UNITS bytesrw INTEGER .1.3.6.1.4.1.89.59.6.6.1.14 |
rlPolicyDropProfileTablethis table defines drop profile
which describ the queue's drop
algorithems SEQUENCE OF RlPolicyDropProfileEntry .1.3.6.1.4.1.89.59.6.7 |
rlPolicyDropProfileEntryConfiguration parameters for each port/service class. RlPolicyDropProfileEntry .1.3.6.1.4.1.89.59.6.7.1 |
rlPolicyDropProfileIndexInterface index.ro INTEGER .1.3.6.1.4.1.89.59.6.7.1.1 |
rlPolicyDropProfileQueueNumberInterface Queue number.ro INTEGER .1.3.6.1.4.1.89.59.6.7.1.2 |
rlPolicyDropProfileTdThersholdDp0Tail Drop Threshold for Drop Precedence 0.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.3 |
rlPolicyDropProfileTdThersholdDp1Tail Drop Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.4 |
rlPolicyDropProfileTdThersholdDp2Tail Drop Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.5 |
rlPolicyDropProfileRedMinDp0WRED Min Threshold for Drop Precedence 0.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.6 |
rlPolicyDropProfileRedMaxDp0WRED Max Threshold for Drop Precedence 0.
UNITS percent 0-100 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.7 |
rlPolicyDropProfileRedProbDp0WRED probability for Drop Precedence 0.rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.8 |
rlPolicyDropProfileRedMinDp1WRED Min Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.9 |
rlPolicyDropProfileRedMaxDp1WRED Max Threshold for Drop Precedence 1.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.10 |
rlPolicyDropProfileRedProbDp1WRED probability for Drop Precedence 1.rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.11 |
rlPolicyDropProfileRedMinDp2WRED Min Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.12 |
rlPolicyDropProfileRedMaxDp2WRED Max Threshold for Drop Precedence 2.
UNITS percent 0-100rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.13 |
rlPolicyDropProfileRedProbDp2WRED probability for Drop Precedence 2.rw INTEGER .1.3.6.1.4.1.89.59.6.7.1.14 |
rlPolicyDropProfileRedQweightadditional parameter for the WRED algorithem supporting
the Queue weight exponentail factorrw INTEGER .1.3.6.1.4.1.89.59.6.7.1.15 |
rlPolicyDropProfileStatusStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.7.1.16 |
rlPolicyVlanConfigurationTableThis table enables the network administrator to fine-tune
the rate limit given to each vlan.
The values in this table will thus override those of the
rlQosIfPolicyTable (THIS TABLE IS MANAGED FROM 3SW). SEQUENCE OF RlPolicyVlanCfgEntry .1.3.6.1.4.1.89.59.6.8 |
rlPolicyVlanCfgEntryConfiguration parameters for each vlan. RlPolicyVlanCfgEntry .1.3.6.1.4.1.89.59.6.8.1 |
rlPolicyVlanCfgVlanIdInterface index.ro VlanId (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.59.6.8.1.1 |
rlPolicyVlanCfgPortRateLimitStatusIf there is Rate Limit on the vlanrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.8.1.2 |
rlPolicyVlanCfgCirPortRateLimitThe CIR for the port Rate limit.
N/A when the Rate limit is disabled
UNITS bps bits per secondrw INTEGER .1.3.6.1.4.1.89.59.6.8.1.3 |
rlPolicyVlanCfgCbsPortRateLimitThe CBS for the port Rate Limit.
N/A when the Rate Limit is disabled.
UNITS bytesrw INTEGER .1.3.6.1.4.1.89.59.6.8.1.4 |
rlPolicyVlanCfgStatusStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.6.8.1.5 |
rlPolicyDiffServ OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.7 |
rlPolicyDiffServPlatDependParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.7.1 |
rlDiffservModeSupportedIndicates whether Diffserv mode is supported on the platform.roobsolete Enumeration .1.3.6.1.4.1.89.59.7.1.1 |
rlDiffservModeEnabledIndicates whether Diffserv mode is currently enabled.rw Enumeration .1.3.6.1.4.1.89.59.7.2 |
rlDiffservBoundaryTableIndicates whether a port is considered a boundary or an interior
node of the Diffserv domain SEQUENCE OF RlDiffservBoundaryEntry .1.3.6.1.4.1.89.59.7.3 |
rlDiffservBoundaryEntryEach boundary/interior ports table entry consists of the following
parameters RlDiffservBoundaryEntry .1.3.6.1.4.1.89.59.7.3.1 |
rlDiffservBoundaryIfIndexThe Interface index whose type is being definedro INTEGER .1.3.6.1.4.1.89.59.7.3.1.1 |
rlDiffservBoundaryPortTypeThe boundary status of the port.rw Enumeration .1.3.6.1.4.1.89.59.7.3.1.2 |
rlDiffservBoundaryStatusStatus of this entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.7.3.1.3 |
rlPolicyGlobalParams OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.9 |
rlPolicyGlobalOperationEnabledIndicates whether Policy is currently enabled.rw Enumeration .1.3.6.1.4.1.89.59.9.1 |
rlPolicyGlobalDefaultForwardingIndicates whether or not the unmach traffic
is forwarded or blocked.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.9.2 |
rlPolicyGlobalAdminTrapfrequencydefine the the min number of seconds between successive traps.
0 means no traps will be sent, uints in Secrw INTEGER .1.3.6.1.4.1.89.59.9.3 |
rlPolicyGlobalOperTrapElapsedTimeshow the time out elaps from the last trap sent
uints in Sec.ro INTEGER .1.3.6.1.4.1.89.59.9.4 |
rlPolicyGlobalQosModeV750 DEPRECATED - replaced with rlPolicyGlobalQosMode field in rlPolicyQosModeGlobalCfg table.
user can set the system to operate either in the Basic mode or in the Advanced moderwdeprecated RlPolicyQosMode .1.3.6.1.4.1.89.59.9.5 |
rlPolicyGlobalTrustModeV750 DEPRECATED - replaced with rlPolicyGlobalTrustMode field in rlPolicyQosModeGlobalCfg table.
Global Trust state. the value refered to Basic mode and specify
the trust mode the device is support. all phisical ports are trustedrwdeprecated RlPolicyTrustTypes .1.3.6.1.4.1.89.59.9.6 |
rlPolicyGlobalDeviceQosOperationTypesIndicates if the system support basic
or advanced mode or Both basic and Advancedro Enumeration .1.3.6.1.4.1.89.59.9.7 |
rlPolicyGlobalDscpMutationSupportedmutation over the ingress packet dscp field
supported for the device.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.9.8 |
rlPolicyGlobalClassifyIpPrecedenceSupportedIndicates if the system support
classification according ip precedence
most significant 3 bits in the TOS byteroobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.9.9 |
rlPolicyGlobalDeviceShapingTypeSupportedIndicates the shaper shaper type supported for the devicero Enumeration .1.3.6.1.4.1.89.59.9.10 |
rlPolicyGlobalDscpRemarkingSupportedIndicates if dscp remarking
supported for the devicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.9.11 |
rlPolicyGlobalqueueSchedulerPerDeviceOrPortindicates if the system support scheduling
configuration per port or per device.
device (1 ) or port (2)roobsolete Enumeration .1.3.6.1.4.1.89.59.9.12 |
rlPolicyMapping OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.10 |
rlPolicyDscpServiceClassTableThis table specifies The DSCP
to ServiceClass map table SEQUENCE OF RlPolicyDscpServiceClassEntry .1.3.6.1.4.1.89.59.10.1 |
rlPolicyDscpServiceClassEntryEach entry in this table describes The ServiceClass assigned to a Dscp value.
The index is DSCP represent by rlPolicyDscpIndex RlPolicyDscpServiceClassEntry .1.3.6.1.4.1.89.59.10.1.1 |
rlPolicyDscpIndexDSCP value.ro INTEGER .1.3.6.1.4.1.89.59.10.1.1.1 |
rlPolicyServiceClassValueServiceClass value.rw INTEGER .1.3.6.1.4.1.89.59.10.1.1.2 |
rlPolicyDscpServiceClassStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.1.1.3 |
rlPolicyTcpUdpPortServiceClassTableThis table specifies TCP/UDP
Port to ServiceClass map tableobsolete SEQUENCE OF RlPolicyTcpUdpPortServiceClassEntry .1.3.6.1.4.1.89.59.10.2 |
rlPolicyTcpUdpPortServiceClassEntryEach entry in this table describes The
ServiceClass Value.
The index is TCP/UDP port represent by rlPolicyTcpUdpPortobsolete RlPolicyTcpUdpPortServiceClassEntry .1.3.6.1.4.1.89.59.10.2.1 |
rlPolicyProtocolTypeTCP/UDP port type.roobsolete L4ProtType .1.3.6.1.4.1.89.59.10.2.1.1 |
rlPolicyTcpUdpPortTCP/UDP port number.roobsolete INTEGER .1.3.6.1.4.1.89.59.10.2.1.2 |
rlPolicyMappedServiceClassServiceClass value.rwobsolete INTEGER .1.3.6.1.4.1.89.59.10.2.1.3 |
rlPolicyTcpUdpPortServiceClassStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.2.1.4 |
rlPolicyDscpRemarkTableThis table specifies The DSCP
Remark table SEQUENCE OF RlPolicyDscpRemarkEntry .1.3.6.1.4.1.89.59.10.3 |
rlPolicyDscpRemarkEntryEach entry in this table describes the new
DSCP for the packet.
The index is Old DSCP represent by rlPolicyOldDscp RlPolicyDscpRemarkEntry .1.3.6.1.4.1.89.59.10.3.1 |
rlPolicyRmOldDscpOld DSCP.ro INTEGER .1.3.6.1.4.1.89.59.10.3.1.1 |
rlPolicyRmNewDscpNew DSCP.rw INTEGER .1.3.6.1.4.1.89.59.10.3.1.2 |
rlPolicyDscpRemarkStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.3.1.3 |
rlPolicyDscpMutationTableThis table specifies The DSCP
Mutation table SEQUENCE OF RlPolicyDscpMutationEntry .1.3.6.1.4.1.89.59.10.4 |
rlPolicyDscpMutationEntryEach entry in this table describes the new
DSCP for the packet.
The index is Old DSCP represent by rlPolicyOldDscp RlPolicyDscpMutationEntry .1.3.6.1.4.1.89.59.10.4.1 |
rlPolicyOldDscpOld DSCP.ro INTEGER .1.3.6.1.4.1.89.59.10.4.1.1 |
rlPolicyNewDscpNew DSCP.rw INTEGER .1.3.6.1.4.1.89.59.10.4.1.2 |
rlPolicyDscpMutationStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.4.1.3 |
rlPolicyTrustModeTableThis table specifies the port state for the trusted basic mode SEQUENCE OF RlPolicyTrustModeEntry .1.3.6.1.4.1.89.59.10.5 |
rlPolicyTrustModeEntrydescribes the ports status that belongs to the global trusted state RlPolicyTrustModeEntry .1.3.6.1.4.1.89.59.10.5.1 |
rlPolicyTrustModePortNumberphisical port number .ro INTEGER .1.3.6.1.4.1.89.59.10.5.1.1 |
rlPolicyTrustModePortStatethe port state for the trusted mode.
the port can be enabled or disabled for the basic trust moderw Enumeration .1.3.6.1.4.1.89.59.10.5.1.2 |
rlPolicyDscpVptTableThis table specifies The DSCP to VPT map table SEQUENCE OF RlPolicyDscpVptEntry .1.3.6.1.4.1.89.59.10.6 |
rlPolicyDscpVptEntryEach entry in this table describes The VPT assigned to a Dscp value.
The index is DSCP represent by rlPolicyDscpValue. RlPolicyDscpVptEntry .1.3.6.1.4.1.89.59.10.6.1 |
rlPolicyDscpValueDSCP value.ro INTEGER .1.3.6.1.4.1.89.59.10.6.1.1 |
rlPolicyVptValueVPT value.rw INTEGER .1.3.6.1.4.1.89.59.10.6.1.2 |
rlPolicyDscpVptStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.6.1.3 |
rlPolicyDscpToDpTableThis table specifies The DSCP
To Dp table SEQUENCE OF RlPolicyDscpToDpEntry .1.3.6.1.4.1.89.59.10.7 |
rlPolicyDscpToDpEntryEach entry in this table describes the new
DP for the packet.
The index is DSCP represent by rlPolicyDscp RlPolicyDscpToDpEntry .1.3.6.1.4.1.89.59.10.7.1 |
rlPolicyDscpPacket DSCP.ro INTEGER .1.3.6.1.4.1.89.59.10.7.1.1 |
rlPolicyDpNew DP.rw INTEGER .1.3.6.1.4.1.89.59.10.7.1.2 |
rlPolicyDscpToDpStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.10.7.1.3 |
rlPolicyDefaultForwardingTableThis table specifies The default forwarding
values : permit or deny for list of specific ports , vlans SEQUENCE OF RlPolicyDefaultForwardingEntry .1.3.6.1.4.1.89.59.11 |
rlPolicyDefaultForwardingEntrySince the table is search to find match according to first match
Entries with specific protocol should be set before entries for entire layer. RlPolicyDefaultForwardingEntry .1.3.6.1.4.1.89.59.11.1 |
rlPolicyDefaultForwardingIndexDefault Forwarding Index.ro INTEGER .1.3.6.1.4.1.89.59.11.1.1 |
rlPolicyDefaultForwardingPortListDefault Forwarding Port List.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.59.11.1.2 |
rlPolicyDefaultForwardingVlanId1To1024Default Forwarding VlanId List 1.rw VlanList1 (Dell-BRIDGEMIBOBJECTS-MIB) .1.3.6.1.4.1.89.59.11.1.3 |
rlPolicyDefaultForwardingVlanId1025To2048Default Forwarding VlanId List 2.rw VlanList2 (Dell-BRIDGEMIBOBJECTS-MIB) .1.3.6.1.4.1.89.59.11.1.4 |
rlPolicyDefaultForwardingVlanId2049To3072Default Forwarding VlanId List 3.rw VlanList3 (Dell-BRIDGEMIBOBJECTS-MIB) .1.3.6.1.4.1.89.59.11.1.5 |
rlPolicyDefaultForwardingVlanId3073To4096Default Forwarding VlanId List 4.rw VlanList4 (Dell-BRIDGEMIBOBJECTS-MIB) .1.3.6.1.4.1.89.59.11.1.6 |
rlPolicyDefaultForwardingLayerDefault Forwarding Action specify layer l2 l3 l3-ipv6rw Enumeration .1.3.6.1.4.1.89.59.11.1.7 |
rlPolicyDefaultForwardingActionDefault Forwarding Action specify permit or denyrw Enumeration .1.3.6.1.4.1.89.59.11.1.8 |
rlPolicyDefaultForwardingStatusThe status of a table entry.
It is used to delete/Add an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.11.1.9 |
rlPolicyDefaultForwardingProtocolThe protocol type to be applied with the default action.rw Enumeration .1.3.6.1.4.1.89.59.11.1.10 |
rlPolicyStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.12 |
rlPolicyPortPolicyStatisticsTableThis table specifies statistics counter for policies with specific actions SEQUENCE OF RlPolicyPortPolicyStatisticsEntry .1.3.6.1.4.1.89.59.12.1 |
rlPolicyPortPolicyStatisticsEntryEach entry in this table describes counter per port.
The index is port represent by rlIfIndex.
In each entry represents counter, it's type , it's size and whether it's enabled. RlPolicyPortPolicyStatisticsEntry .1.3.6.1.4.1.89.59.12.1.1 |
rlPolicyPortPolicyStatisticsIfIndexInterface index.rw INTEGER .1.3.6.1.4.1.89.59.12.1.1.1 |
rlPolicyPortPolicyStatisticsCntrTypeCounter type.ro StatisticsCntrType .1.3.6.1.4.1.89.59.12.1.1.2 |
rlPolicyPolicyStatisticsCntrSizeCounter size in bits.ro StatisticsCntrNumOfBitsType .1.3.6.1.4.1.89.59.12.1.1.3 |
rlPolicyPolicyStatisticsEnableCountingIndication whether the counter is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.1.1.4 |
rlPolicyPolicyStatisticsCounterValueCounter value.ro Counter64 .1.3.6.1.4.1.89.59.12.1.1.5 |
rlPolicyOutQueueStatisticsTableEach entry in this table describes counter per any permutation of
Port/VLAN/Queue/Drop Precedence . Each of the above can a group off 'All'.
The index is port represent by rlPolicyOutQueueStatisticsCountrID.
In each entry there are fields representing
whether the counter is enabled and counters value. SEQUENCE OF RlPolicyOutQueueStatisticsEntry .1.3.6.1.4.1.89.59.12.2 |
rlPolicyOutQueueStatisticsEntryEach entry includes port, vlan, queue, drop precedence and counter value. RlPolicyOutQueueStatisticsEntry .1.3.6.1.4.1.89.59.12.2.1 |
rlPolicyOutQueueStatisticsCountrIDCounter id, the key of the table.ro INTEGER .1.3.6.1.4.1.89.59.12.2.1.1 |
rlPolicyOutQueueStatisticsIfIndexListPort for which the flow is counted.rw PortList (Q-BRIDGE-MIB) .1.3.6.1.4.1.89.59.12.2.1.2 |
rlPolicyOutQueueStatisticsPortAllIndication for whether the port is configured as range of all the portsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.2.1.3 |
rlPolicyOutQueueStatisticsVlanVLAN for which the flow is counted.rw INTEGER .1.3.6.1.4.1.89.59.12.2.1.4 |
rlPolicyOutQueueStatisticsVlanAllIndication for whether the Vlan is configured as range of all the Vlansrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.2.1.5 |
rlPolicyOutQueueStatisticsQueueQueue for which the flow is counted.rw INTEGER .1.3.6.1.4.1.89.59.12.2.1.6 |
rlPolicyOutQueueStatisticsQueueAllIndication for whether the Queue is configured as range of all the Queuesrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.2.1.7 |
rlPolicyOutQueueStatisticsDPDrop Precedence for which the flow is counted.rw StatisticsDPType .1.3.6.1.4.1.89.59.12.2.1.8 |
rlPolicyOutQueueStatisticsDPAllIndication for whether the DP is configured as range of all the DPsrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.2.1.9 |
rlPolicyOutQueueStatisticsCounterTailDropValueThe counter for tail dropped value.ro Counter64 .1.3.6.1.4.1.89.59.12.2.1.10 |
rlPolicyOutQueueStatisticsCounterAllValueThe counter for all traffic value.ro Counter64 .1.3.6.1.4.1.89.59.12.2.1.11 |
rlPolicyOutQueueStatisticsCntrNumOfBitsCounter size in bits for the counter.ro StatisticsCntrNumOfBitsType .1.3.6.1.4.1.89.59.12.2.1.12 |
rlPolicyOutQueueStatisticsStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.2.1.13 |
rlPolicyGlobalStatisticsCntrsTableThis table specifies statistics global counters for specific rules for
all ports that they are connected to SEQUENCE OF RlPolicyGlobalStatisticsCntrsEntry .1.3.6.1.4.1.89.59.12.3 |
rlPolicyGlobalStatisticsCntrsEntryEach entry represents global counter. RlPolicyGlobalStatisticsCntrsEntry .1.3.6.1.4.1.89.59.12.3.1 |
rlPolicyGlobalStatisticsCntrsTypeCounter type.ro StatisticsCntrType .1.3.6.1.4.1.89.59.12.3.1.1 |
rlPolicyGlobalStatisticsCntrsNumOfBitsCounter size in bits.ro StatisticsCntrNumOfBitsType .1.3.6.1.4.1.89.59.12.3.1.2 |
rlPolicyGlobalStatisticsCntrsCounterValueCounter value.ro Counter64 .1.3.6.1.4.1.89.59.12.3.1.3 |
rlPolicyGlobalStatisticsStatusThe status of a table entry.
It is used to delete an entry from this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.12.3.1.4 |
rlPolicyClearCountersThis scalar indicates to clear all the counters.rw INTEGER .1.3.6.1.4.1.89.59.12.4 |
rlPolicyClassifierUtilization OBJECT IDENTIFIER .1.3.6.1.4.1.89.59.13 |
rlPolicyClassifierUtilizationTableA table containing Classifier utilization information.
Each row represents objects for a particular Unit
present in this system. SEQUENCE OF RlPolicyClassifierUtilizationEntry .1.3.6.1.4.1.89.59.13.1 |
rlPolicyClassifierUtilizationEntryA Single entry containing Classifier utilization information. RlPolicyClassifierUtilizationEntry .1.3.6.1.4.1.89.59.13.1.1 |
rlPolicyClassifierUtilizationUnitIdThe Unit ID of this Classifier. must be unique per entry.
This is an index into the table. Unsigned32 .1.3.6.1.4.1.89.59.13.1.1.1 |
rlPolicyClassifierUtilizationPercentThe classifier utilization percentage.ro Unsigned32 .1.3.6.1.4.1.89.59.13.1.1.2 |
rlPolicyClassifierUtilizationRulesNumberThe classifier utilization number of used rules, in short rules resolution.ro Unsigned32 .1.3.6.1.4.1.89.59.13.1.1.3 |
rlPolicyIsTCAvailableThis scalar indicates the number of currently reserved amount
of traffic conditioners.ro Unsigned32 .1.3.6.1.4.1.89.59.14 |
rlPolicyCPUSafeGuardEnableThis scalar enables/disables CPU Safeguard.rw INTEGER .1.3.6.1.4.1.89.59.15 |
rlPolicyQosModeGlobalCfgTableThis table responsible to set the global qos mode configuration:
qos mode, qos trust mode, and if port are trusted by default in qos advanced
mode. SEQUENCE OF RlPolicyQosModeGlobalCfgEntry .1.3.6.1.4.1.89.59.16 |
rlPolicyQosModeGlobalCfgEntryThis table responsible to set the global qos mode configuration:
qos mode, qos trust mode, and if port are trusted by default in qos advanced
mode.
Current implemnetaion assumes only one entry exist. RlPolicyQosModeGlobalCfgEntry .1.3.6.1.4.1.89.59.16.1 |
rlPolicyGlobalIndexEntry index - currenly only one entry can exist, indexes hard coded with value '1'. INTEGER .1.3.6.1.4.1.89.59.16.1.1 |
rlPolicyGlobalQoSModeThis field replaces deprecated scalar rlPolicyCliQosMode.
Defines the global qos operation mode: disable, basic or advnaced.rw RlPolicyQosMode .1.3.6.1.4.1.89.59.16.1.2 |
rlPolicyBasicGlobalTrustModeThis field replaces deprecated scalar rlPolicyCliBasicModeCfg.
Defines the global qos trust operation mode when qos mode is basic.rw RlPolicyTrustTypes .1.3.6.1.4.1.89.59.16.1.3 |
rlPolicyAdvcGlobalTrustModeThis field replaces deprecated scalar rlPolicyCliBasicModeCfg.
Defines the global qos trust operation mode when qos mode is advanced.rw RlPolicyTrustTypes .1.3.6.1.4.1.89.59.16.1.4 |
rlPolicyPortTrustAdvancedModeThis field specified whether ports are set to trused or not-trusted by
default when switching to qos advanced mode.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.16.1.5 |
rlPolicyDscpMutationEnableThis field indicates if dscp to dscp mutation mode is enable.
It can be set to true in the following terms:
1.rlQosGlobalTrustMode is in {dscp, vpt-dscp} ( rlQosGlobalQoSMode must be basic or advanced)
2.if rlQosGlobalQoSMode is advanced then rlQoSPortTrustAdvancedMode must be set to true.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.59.16.1.6 |
rlPolicyModeGlobalCfgStatusThis status of entry action.
In current implementation only one entry exist, therefor only status = active is
acceptable.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.59.16.1.7 |