Dell-IPv6
The private MIB module definition for IPv6 MIB.
Main OID:
rlIPv6.1.3.6.1.4.1.89.129
142
Objects
Active
Status
10
Dependencies
Imported Objects
Objects
142 total| Object Name |
|---|
rlIpAddressTableThis table is parallel to ipAddressTable, and is used to
add/delete IPv6 entries to/from that table. It contains
private objects. SEQUENCE OF RlIpAddressEntry .1.3.6.1.4.1.89.26.19 |
rlIpAddressEntryAn address mapping for a particular interface. RlIpAddressEntry .1.3.6.1.4.1.89.26.19.1 |
rlIpAddressPrefixLengthThe prefix length of this address.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.19.1.1 |
rlIpAddressTypeExtend standard field ipAddressType to multicastro Enumeration .1.3.6.1.4.1.89.26.19.1.2 |
rlipv6InterfaceTableThis table is parallel to ipv6InterfaceTable, and is used to
configure additional interface parameters. SEQUENCE OF Rlipv6InterfaceEntry .1.3.6.1.4.1.89.26.20 |
rlipv6InterfaceEntryAdditional configuration parameters for a particular interface. Rlipv6InterfaceEntry .1.3.6.1.4.1.89.26.20.1 |
rlipv6InterfaceNdDadAttempsND Duplicated address detection number of attempts.rw INTEGER .1.3.6.1.4.1.89.26.20.1.1 |
rlipv6InterfaceAutoconfigEnableEnables or disables Stateless Address Auto configuration
on specific interface.rw Enumeration .1.3.6.1.4.1.89.26.20.1.2 |
rlipv6InterfaceIcmpUnreachSendEnableEnables or disables sending of ICMP Destination Unreachable
Error on specific interface.rw Enumeration .1.3.6.1.4.1.89.26.20.1.3 |
rlipv6InterfaceLinkMTUThe maximum transmission unit (MTU) size of IPv6 packets
sent on an interface in bytes.rw Unsigned32 .1.3.6.1.4.1.89.26.20.1.4 |
rlipv6InterfaceMLDVersionSet version of MLD protocol on specific interface.rw Unsigned32 .1.3.6.1.4.1.89.26.20.1.5 |
rlipv6InterfaceRetransmitTimeThis value will be included in all IPv6 router advertisements sent
out this interface. Very short intervals are not recommended in
normal IPv6 operation. When a nondefault value is configured, the
configured time is both advertised and used by the router itself.
When value 0 is configured, 0 seconds (unspecified) advertised in
router advertisements and the value 1000 milliseconds is used for
the neighbor discovery activity of the router itself.rw Unsigned32 (0 | 1000..3600000) UNITS "milliseconds" .1.3.6.1.4.1.89.26.20.1.6 |
rlipv6InterfaceIcmpRedirectSendEnableEnables or disables sending of ICMP IPv6 redirect messages to
re-send a packet through the same interface on which the packet was
received.rw Enumeration .1.3.6.1.4.1.89.26.20.1.7 |
rlinetCidrRouteTableThis table is parallel to inetCidrRouteTable, and is used to
configure or display additional route parameters. SEQUENCE OF RlinetCidrRouteEntry .1.3.6.1.4.1.89.26.21 |
rlinetCidrRouteEntryAdditional parameters for a particular route. RlinetCidrRouteEntry .1.3.6.1.4.1.89.26.21.1 |
rlinetCidrRouteLifetimeThe remaining length of time, in seconds, that this route
will continue to be valid, i.e., time until deprecation.
A value of 4,294,967,295 represents infinity.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.26.21.1.1 |
rlinetCidrRouteInfoA reference to MIB definitions specific to the particular routing
protocol which is responsible for this route, as determined by the
value specified in the route's inetCidrRouteProto value.ro Enumeration .1.3.6.1.4.1.89.26.21.1.2 |
rlipNetToPhysicalTableThis table is parallel to ipNetToPhysicalTable, and is used to
configure or display additional neighbor parameters. SEQUENCE OF RlipNetToPhysicalEntry .1.3.6.1.4.1.89.26.22 |
rlipNetToPhysicalEntryAdditional parameters for a neighbor RlipNetToPhysicalEntry .1.3.6.1.4.1.89.26.22.1 |
rlipNetToPhysicalIsRouterThis object has the value 'true(1)', if the neighbor
is router; otherwise, the value is 'false(2)'.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.26.22.1.1 |
rlipNetToPhysicalReachableConfirmedTime (in seconds) since the address was confirmed to be reachable.
Only, relevant for dynamic entries.ro Unsigned32 .1.3.6.1.4.1.89.26.22.1.2 |
rlInetStaticRouteTableThis entity's static (user configured) Inet Routing table.
Entries are MAX-ACCESSible even if not used for forwarding SEQUENCE OF RlInetStaticRouteEntry .1.3.6.1.4.1.89.26.28 |
rlInetStaticRouteEntryA particular Static(user configured) route to a particular destination. RlInetStaticRouteEntry .1.3.6.1.4.1.89.26.28.1 |
rlInetStaticRouteDestTypeThe type of the address used as the destination
internetwork address or subnet address.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.28.1.1 |
rlInetStaticRouteDestDestination internetwork address or subnet address. The
destination prefix length is applied to this value, and to a
particular destination address, to determine whether the route
applies to the particular address.
If the prefix length is L, then applying the length to an address
means taking the first L bits of the address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.28.1.2 |
rlInetStaticRoutePfxLenIndicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInetStaticRouteDest field. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.28.1.3 |
rlInetStaticRouteNextHopTypeThe type of the address used as the next-hop address
for this route. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.28.1.4 |
rlInetStaticRouteNextHopThe next-hop IP address, if any.
If rlInetStaticRouteAction is 'forward', there may or may not be
a next-hop IP address.
A next-hop IP address is not required if an output interface
index is specified (in other words, if rlInetStaticRouteIfIndex is
non-zero).
If rlInetStaticRouteAction is not 'forward', there is no next-hop
IP address.
If there is no next-hop IP address, the rlInetStaticRouteNextHop
object is set to all zeroes. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.28.1.5 |
rlInetStaticRouteIfIndexThe ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.26.28.1.6 |
rlInetStaticRoutePathCostPath cost for this static route.rw Unsigned32 .1.3.6.1.4.1.89.26.28.1.7 |
rlInetStaticRouteTypeSame as inetCidrRouteType MIB (excluded 'other' route type)rw Enumeration .1.3.6.1.4.1.89.26.28.1.8 |
rlInetStaticRouteOwnerStatic - The route is configured over Static IP.
This route is written to configuration files.
Dhcp - The route is Configured by DHCP
(received as part of DHCP configuration)
This route IS NOT written to configuration files
Default - The route is Configured by default system config
exists till any other configuration is applied.
Icmp - The route is Configured by ICMP protocol either by
router advertisements or to be advertised in router
advertisements .ro Enumeration .1.3.6.1.4.1.89.26.28.1.9 |
rlInetStaticRouteRowStatusThe row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.26.28.1.10 |
rlInetStaticRouteForwardingStatusactive - An indication that the route has implication on routing
inactive - the route is a backup route or it is down. It is not used
in forwarding decision.
Down means that the Ip interface on which it is configured is down.
(Note: ip interface down may be for two reason - its admin status or
the L2 interface , on which the ip interface is configured, statusro Enumeration .1.3.6.1.4.1.89.26.28.1.11 |
rlInetRoutingDistanceTableThis table defines administrative distances for
different protocol routes that are inserted into
the routing table. SEQUENCE OF RlInetRoutingDistanceEntry .1.3.6.1.4.1.89.26.29 |
rlInetRoutingDistanceEntryA set of distances per inet address type. RlInetRoutingDistanceEntry .1.3.6.1.4.1.89.26.29.1 |
rlInetRoutingDistanceTypeThe inet address type for distance definitions set,
either IPv4 or IPv6.ro Enumeration .1.3.6.1.4.1.89.26.29.1.1 |
rlInetRoutingDistanceConnectedThe administrative distance used for directly connected routes.rw INTEGER .1.3.6.1.4.1.89.26.29.1.2 |
rlInetRoutingDistanceStaticThe administrative distance used for static routes.rw INTEGER .1.3.6.1.4.1.89.26.29.1.3 |
rlInetRoutingDistanceRipThe administrative distance used for RIP routes.rw INTEGER .1.3.6.1.4.1.89.26.29.1.4 |
rlInetRoutingDistanceOspfInternalThe administrative distance used for OSPF internal routes.rw INTEGER .1.3.6.1.4.1.89.26.29.1.5 |
rlInetRoutingDistanceOspfExternalThe administrative distance used for OSPF Autonomous System external routes.rw INTEGER .1.3.6.1.4.1.89.26.29.1.6 |
rlInternInetCidrRouteTableInternal inetCidrRouteTable - this entity's IP Routing table. SEQUENCE OF RlInternInetCidrRouteEntry .1.3.6.1.4.1.89.26.30 |
rlInternInetCidrRouteEntryA particular route to a particular destination, under a
particular policy (as reflected in the
rlInternInetCidrRoutePolicy object).
Dynamically created rows will survive an agent reboot.
Implementers need to be aware that if the total number
of elements (octets or sub-identifiers) in
rlInternInetCidrRouteDest, rlInternInetCidrRoutePolicy, and
rlInternInetCidrRouteNextHop exceeds 111, then OIDs of column
instances in this table will have more than 128 sub-
identifiers and cannot be accessed using SNMPv1,
SNMPv2c, or SNMPv3. RlInternInetCidrRouteEntry .1.3.6.1.4.1.89.26.30.1 |
rlInternInetCidrRouteDestTypeThe type of the rlInternInetCidrRouteDest address, as defined
in the InetAddress MIB.
Only those address types that may appear in an actual
routing table are allowed as values of this object. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.1 |
rlInternInetCidrRouteDestThe destination IP address of this route.
The type of this address is determined by the value of
the rlInternInetCidrRouteDestType object.
The values for the index objects rlInternInetCidrRouteDest and
rlInternInetCidrRoutePfxLen must be consistent. When the value
of rlInternInetCidrRouteDest (excluding the zone index, if one
is present) is x, then the bitwise logical-AND
of x with the value of the mask formed from the
corresponding index object rlInternInetCidrRoutePfxLen MUST be
equal to x. If not, then the index pair is not
consistent and an inconsistentName error must be
returned on SET or CREATE requests. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.2 |
rlInternInetCidrRoutePfxLenIndicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInternInetCidrRouteDest field.
The values for the index objects rlInternInetCidrRouteDest and
rlInternInetCidrRoutePfxLen must be consistent. When the value
of rlInternInetCidrRouteDest (excluding the zone index, if one
is present) is x, then the bitwise logical-AND
of x with the value of the mask formed from the
corresponding index object rlInternInetCidrRoutePfxLen MUST be
equal to x. If not, then the index pair is not
consistent and an inconsistentName error must be
returned on SET or CREATE requests. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.3 |
rlInternInetCidrRoutePolicyThis object is an opaque object without any defined
semantics. Its purpose is to serve as an additional
index that may delineate between multiple entries to
the same destination. The value { 0 0 } shall be used
as the default value for this object. OBJECT IDENTIFIER .1.3.6.1.4.1.89.26.30.1.4 |
rlInternInetCidrRouteNextHopTypeThe type of the rlInternInetCidrRouteNextHop address, as
defined in the InetAddress MIB.
Value should be set to unknown(0) for non-remote
routes.
Only those address types that may appear in an actual
routing table are allowed as values of this object. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.5 |
rlInternInetCidrRouteNextHopOn remote routes, the address of the next system en
route. For non-remote routes, a zero length string.
The type of this address is determined by the value of
the rlInternInetCidrRouteNextHopType object. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.6 |
rlInternInetCidrRouteIfIndexThe ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.26.30.1.7 |
rlInternInetCidrRouteTypeThe type of route. Note that local(3) refers to a
route for which the next hop is the final destination;
remote(4) refers to a route for which the next hop is
not the final destination.
Routes that do not result in traffic forwarding or
rejection should not be displayed, even if the
implementation keeps them stored internally.
reject(2) refers to a route that, if matched, discards
the message as unreachable and returns a notification
(e.g., ICMP error) to the message sender. This is used
in some protocols as a means of correctly aggregating
routes.
blackhole(5) refers to a route that, if matched,
discards the message silently.ro Enumeration .1.3.6.1.4.1.89.26.30.1.8 |
rlInternInetCidrRouteProtoThe routing mechanism via which this route was learned.
Inclusion of values for gateway routing protocols is
not intended to imply that hosts should support those
protocols.ro IANAipRouteProtocol (IANA-RTPROTO-MIB) .1.3.6.1.4.1.89.26.30.1.9 |
rlInternInetCidrRouteAgeThe number of seconds since this route was last updated
or otherwise determined to be correct. Note that no
semantics of 'too old' can be implied, except through
knowledge of the routing protocol by which the route
was learned.ro Gauge32 .1.3.6.1.4.1.89.26.30.1.10 |
rlInternInetCidrRouteNextHopASThe Autonomous System Number of the Next Hop. The
semantics of this object are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. When this object is unknown or not relevant, its
value should be set to zero.ro InetAutonomousSystemNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.30.1.11 |
rlInternInetCidrRouteMetric1The primary routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should be
set to -1.ro Integer32 .1.3.6.1.4.1.89.26.30.1.12 |
rlInternInetCidrRouteMetric2An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should be
set to -1.ro Integer32 .1.3.6.1.4.1.89.26.30.1.13 |
rlInternInetCidrRouteMetric3An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should be
set to -1.ro Integer32 .1.3.6.1.4.1.89.26.30.1.14 |
rlInternInetCidrRouteMetric4An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should be
set to -1.ro Integer32 .1.3.6.1.4.1.89.26.30.1.15 |
rlInternInetCidrRouteMetric5An alternate routing metric for this route. The
semantics of this metric are determined by the routing-
protocol specified in the route's rlInternInetCidrRouteProto
value. If this metric is not used, its value should be
set to -1.ro Integer32 .1.3.6.1.4.1.89.26.30.1.16 |
rlInternInetCidrRouteStatusThe row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1).ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.26.30.1.17 |
rlInternInetCidrRouteLifetimeThe remaining length of time, in seconds, that this route
will continue to be valid, i.e., time until deprecation.
A value of 4,294,967,295 represents infinity.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.26.30.1.18 |
rlInternInetCidrRouteInfoA reference to MIB definitions specific to the particular routing
protocol which is responsible for this route, as determined by the
value specified in the route's inetCidrRouteProto value.ro Enumeration .1.3.6.1.4.1.89.26.30.1.19 |
rlInternInetStaticRouteTableThis entity's static (user configured) Inet Routing table.
Entries are MAX-ACCESSible even if not used for forwarding SEQUENCE OF RlInternInetStaticRouteEntry .1.3.6.1.4.1.89.26.31 |
rlInternInetStaticRouteEntryA particular Static(user configured) route to a particular destination. RlInternInetStaticRouteEntry .1.3.6.1.4.1.89.26.31.1 |
rlInternInetStaticRouteDestTypeThe type of the address used as the destination
internetwork address or subnet address.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.31.1.1 |
rlInternInetStaticRouteDestDestination internetwork address or subnet address. The
destination prefix length is applied to this value, and to a
particular destination address, to determine whether the route
applies to the particular address.
If the prefix length is L, then applying the length to an address
means taking the first L bits of the address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.31.1.2 |
rlInternInetStaticRoutePfxLenIndicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlInternInetStaticRouteDest field. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.31.1.3 |
rlInternInetStaticRouteNextHopTypeThe type of the address used as the next-hop address
for this route. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.31.1.4 |
rlInternInetStaticRouteNextHopThe next-hop IP address, if any.
If rlInternInetStaticRouteAction is 'forward', there may or may not be
a next-hop IP address.
A next-hop IP address is not required if an output interface
index is specified (in other words, if rlInternInetStaticRouteIfIndex is
non-zero).
If rlInternInetStaticRouteAction is not 'forward', there is no next-hop
IP address.
If there is no next-hop IP address, the rlInternInetStaticRouteNextHop
object is set to all zeroes. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.26.31.1.5 |
rlInternInetStaticRouteIfIndexThe ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.26.31.1.6 |
rlInternInetStaticRoutePathCostPath cost for this static route.rw Unsigned32 .1.3.6.1.4.1.89.26.31.1.7 |
rlInternInetStaticRouteTypeSame as inetCidrRouteType MIB (excluded 'other' route type)rw Enumeration .1.3.6.1.4.1.89.26.31.1.8 |
rlInternInetStaticRouteOwnerStatic - The route is configured over Static IP.
This route is written to configuration files.
Dhcp - The route is Configured by DHCP
(received as part of DHCP configuration)
This route IS NOT written to configuration files
Default - The route is Configured by default system config
exists till any other configuration is applied.
Icmp - The route is Configured by ICMP protocol either by
router advertisements or to be advertised in router
advertisements .ro Enumeration .1.3.6.1.4.1.89.26.31.1.9 |
rlInternInetStaticRouteRowStatusThe row status variable, used according to row
installation and removal conventions.
A row entry cannot be modified when the status is
marked as active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.26.31.1.10 |
rlInternInetStaticRouteForwardingStatusactive - An indication that the route has implication on routing
inactive - the route is a backup route or it is down. It is not used
in forwarding decision.
Down means that the Ip interface on which it is configured is down.ro Enumeration .1.3.6.1.4.1.89.26.31.1.11 |
rlIPv6The private MIB module definition for IPv6 MIB. MODULE-IDENTITY .1.3.6.1.4.1.89.129 |
rlipv6IcmpErrorRatelimitIntervalThe time interval between tokens being placed in the bucket,
each token represents a single ICMP error message.
The interval measured in milliseconds.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.89.129.1 |
rlipv6IcmpErrorRatelimitBucketSizeThe maximum number of tokens stored in the bucket,
each token represents a single ICMP error message.rw INTEGER .1.3.6.1.4.1.89.129.2 |
rlipv6LLDefaultZoneThe interface which would be used as the egress interface
for packets sent without a specified IPv6Z interface identifier
or with the default '0' identifier. Zero value means no default
interface specified.rw InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.129.3 |
rlIpv6GeneralPrefixTableThis table defines general prefix description,
based on which a number of longer, more specific, prefixes can
be defined. SEQUENCE OF RlIpv6GeneralPrefixEntry .1.3.6.1.4.1.89.129.4 |
rlIpv6GeneralPrefixEntrySingle entry in general prefix table. RlIpv6GeneralPrefixEntry .1.3.6.1.4.1.89.129.4.1 |
rlIpv6GeneralPrefixNameThe name assigned to the prefix. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.89.129.4.1.1 |
rlIpv6GeneralPrefixInetAddrTypePrefix inet address type. Has to be IPv6.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.4.1.2 |
rlIpv6GeneralPrefixInetAddrThe IPv6 network assigned to the general prefix.
This argument must be in the form documented in RFC4293
where the address is specified in hexadecimal using 16-bit values
between colons.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.4.1.3 |
rlIpv6GeneralPrefixInetAddrPrefixLengthIndicates the number of leading one bits that form the
mask to be logical-ANDed with the inet address
before being compared to the value in the
rlIpv6GeneralPrefixInetAddr field.rw InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.4.1.4 |
rlIpv6GeneralPrefixInterfaceIdInterface id to use when creating prefix based on point-to-point interface.rw Unsigned32 .1.3.6.1.4.1.89.129.4.1.5 |
rlIpv6GeneralPrefixRowStatusRow status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.129.4.1.6 |
rlipv6MaximumHopsNumberMaximum number of hops used in router advertisements and all IPv6 packets that
are originated by the router.rw INTEGER .1.3.6.1.4.1.89.129.5 |
rlIpv6RouterAdvertPrefixTableThis table defines IPv6 prefixes which are included in IPv6 Neighbor
Discovery (ND) router advertisements. SEQUENCE OF RlIpv6RouterAdvertPrefixEntry .1.3.6.1.4.1.89.129.6 |
rlIpv6RouterAdvertPrefixEntrySingle entry in Neighbor Discovery Prefix table. RlIpv6RouterAdvertPrefixEntry .1.3.6.1.4.1.89.129.6.1 |
rlIpv6RouterAdvertPrefixIfIndexThe index value that uniquely identifies the interface on
which this prefix is configured. The interface identified
by a particular value of this index is the same interface as
identified by the same value of the IF-MIB's ifIndex. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.129.6.1.1 |
rlIpv6RouterAdvertPrefixIsDefaultIndicates whether this object belongs to 'default' entry.
Default entry contains specifics about advertising prefixes which
were created from local ipv6 addresses. TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.129.6.1.2 |
rlIpv6RouterAdvertPrefixInetAddrTypePrefix inet address type. Has to be IPv6. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.6.1.3 |
rlIpv6RouterAdvertPrefixInetAddrThe IPv6 network prefix to include in router advertisements.
This argument must be in the form documented in RFC4293 where
the address is specified in hexadecimal using 16-bit values between
colons. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.6.1.4 |
rlIpv6RouterAdvertPrefixInetAddrPrefixLengthThe length of the IPv6 prefix. A decimal value that indicates
how many of the high-order contiguous bits of the address comprise
the prefix (the network portion of the address). InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.6.1.5 |
rlIpv6RouterAdvertPrefixAdminStatusAdmin status of the entry. Relevant only for default entry.rw Enumeration .1.3.6.1.4.1.89.129.6.1.6 |
rlIpv6RouterAdvertPrefixAdvertiseWhether the prefix is included in router advertisements.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.129.6.1.7 |
rlIpv6RouterAdvertPrefixOnLinkStatusIf object has the value 'onlink(1)', this prefix is confidered as on-link.
This prefix will be advertised with the L-bit set and will be present
in the Routing Table.
If object has the value 'not-onlink(2)', this prefix will be advertised
with the L-bit clear, but connected state of the prefix will not be changed.
If object has the value 'offlink(3)', this prefix is confidered as on-link.
This prefix will be advertised with the L-bit clear, and will be
not present in the Routing Table.rw Enumeration .1.3.6.1.4.1.89.129.6.1.8 |
rlIpv6RouterAdvertPrefixAutonomousFlagIf object has the value 'true(1)', this prefix indicates to hosts on
the local link that the specified prefix can be used for IPv6
autoconfiguration. The prefix will be advertised with the A-bit set.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.129.6.1.9 |
rlIpv6RouterAdvertPrefixAdvPreferredLifetimeThe amount of time (in seconds) that the specified IPv6 prefix is
advertised as being preferred.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.129.6.1.10 |
rlIpv6RouterAdvertPrefixAdvValidLifetimeThe amount of time (in seconds) that the specified IPv6 prefix is
advertised as being valid.rw Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.129.6.1.11 |
rlIpv6RouterAdvertPrefixRowStatusRow status.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.89.129.6.1.12 |
rlIpv6RouterAdvertTableThis table is parallel to inetCidrRouteTable, and is used to
configure or display additional route parameters. SEQUENCE OF RlIpv6RouterAdvertEntry .1.3.6.1.4.1.89.129.7 |
rlIpv6RouterAdvertEntryAdditional parameters for a particular route. RlIpv6RouterAdvertEntry .1.3.6.1.4.1.89.129.7.1 |
rlIpv6RouterAdvertAdvIntervalOptionIndicates to a visiting mobile node the interval at which that node
may expect to receive RAs. The node may use this information in its
movement detection algorithm.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.129.7.1.1 |
rlIpv6RouterAdvertRouterPreferenceConfigures a default router preference (DRP) for the router on a specific interface.rw Enumeration .1.3.6.1.4.1.89.129.7.1.2 |
rlIpv6RouterAdvertIsCurHopLimitUserConfiguredIndicates that hop limit value used in router advertisement is
an user configured value and not necessarily value that is used by
router itself.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.89.129.7.1.3 |
rlipv6InetCidrTableClearThis scalar indicates to clear all ipv6 routes from inetCidrTable.rw INTEGER .1.3.6.1.4.1.89.129.8 |
rlIpv6PathMtuTableThis table used to represent all Path MTU changes to specific destination
received from 'packet-too-big' messages. SEQUENCE OF RlIpv6PathMtuEntry .1.3.6.1.4.1.89.129.9 |
rlIpv6PathMtuEntrySingle entry in Path MTU table. RlIpv6PathMtuEntry .1.3.6.1.4.1.89.129.9.1 |
rlIpv6PathMtuEntryInetDestAddrTypePrefix inet address type. Has to be IPv6. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.9.1.1 |
rlIpv6PathMtuEntryInetDestAddrThe IPv6 destination address for which packet-too-big message
was received.
This argument must be in the form documented in RFC4293
where the address is specified in hexadecimal using 16-bit values
between colons. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.9.1.2 |
rlIpv6PathMtuEntryMtuThe MTU value that was received in packet-too-bug message for
specific destination.ro Unsigned32 .1.3.6.1.4.1.89.129.9.1.3 |
rlIpv6PathMtuEntryAgeThis entry's age (seconds)ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.89.129.9.1.4 |
rlIpNetToPhysicalTableClearTableThis entity is used to clear all or specific-type entries from ipNetToPhysicalTable. SEQUENCE OF RlIpNetToPhysicalTableClearEntry .1.3.6.1.4.1.89.129.10 |
rlIpNetToPhysicalTableClearEntryA particular entry in this table. RlIpNetToPhysicalTableClearEntry .1.3.6.1.4.1.89.129.10.1 |
rlIpNetToPhysicalTableClearIfIndexInterface index of to clear or zero in case of whole table. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.129.10.1.1 |
rlIpNetToPhysicalTableClearScopeScope of the action - type of entries to delete.rw Enumeration .1.3.6.1.4.1.89.129.10.1.2 |
rlIpv6HostForwardingTableThis entity's IPv6 host forwarding table. SEQUENCE OF RlIpv6HostForwardingEntry .1.3.6.1.4.1.89.129.11 |
rlIpv6HostForwardingEntryA particular Static(user configured) route to a particular destination. RlIpv6HostForwardingEntry .1.3.6.1.4.1.89.129.11.1 |
rlIpv6HostForwardingDestTypeThe type of the address used as the destination
internetwork address or subnet address.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.11.1.1 |
rlIpv6HostForwardingDestDestination internetwork address or subnet address. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.11.1.2 |
rlIpv6HostForwardingPfxLenIndicates the number of leading one bits that form the
mask to be logical-ANDed with the destination address
before being compared to the value in the
rlIpv6HostForwardingDest field. InetAddressPrefixLength (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.11.1.3 |
rlIpv6HostForwardingNextHopTypeThe type of the address used as the next-hop address
for this route. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.11.1.4 |
rlIpv6HostForwardingNextHopThe next-hop IP address, if any.
A next-hop IP address is not required if an output interface
index is specified (in other words, if rlIpv6HostForwardingIfIndex is
non-zero).
If there is no next-hop IP address, the rlIpv6HostForwardingNextHop
object is set to all zeroes. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.11.1.5 |
rlIpv6HostForwardingIfIndexThe ifIndex value that identifies the local interface
through which the next hop of this route should be
reached. A value of 0 is valid and represents the
scenario where no interface is specified. InterfaceIndexOrZero (IF-MIB) .1.3.6.1.4.1.89.129.11.1.6 |
rlIpv6HostForwardingTypeForwarding type Enumeration .1.3.6.1.4.1.89.129.11.1.7 |
rlIpv6HostForwardingPathCostPath cost for this route.ro Unsigned32 .1.3.6.1.4.1.89.129.11.1.8 |
rlipv6EnabledByDefaultRemovedIfindexthe MIB is relevant when mtsc parameter DHCPv6_client_enabled_by_default is TRUE.
If the MIB has non zero value the meaning is that ipv6 interface has removed from configuration by the user
on the interface and signs to application not to add ipv6 interface. Otherwise (zero value) - the meaning is
that Ipv6 interface must be added.rw INTEGER .1.3.6.1.4.1.89.129.12 |
rlManagementIpv6The system management IPv6 address which is kept between system mode changesrw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.13 |
rlManagementIpv6ActionThe system management IPv6 action:
clear - delete all ipv6 interfaces from startup configuration database except rlManagementIpv6rw Enumeration .1.3.6.1.4.1.89.129.14 |
rlIpv6TunnelToIPv6DbTableThis entity's IPv6 Tunnel if/addr/prefix table. SEQUENCE OF RlIpv6TunnelToIPv6DbEntry .1.3.6.1.4.1.89.129.15 |
rlIpv6TunnelToIPv6DbEntryA particular tunnel configured data to IPv6 db. RlIpv6TunnelToIPv6DbEntry .1.3.6.1.4.1.89.129.15.1 |
rlIpv6TunnelToIPv6IfIndexIfIndex of tunnel interface InterfaceIndex (IF-MIB) .1.3.6.1.4.1.89.129.15.1.1 |
rlIpv6TunnelToIPv6ActionAction of the entry. All other fields relevant for appropriate actions.rw Enumeration .1.3.6.1.4.1.89.129.15.1.2 |
rlIpv6TunnelToIPv6TunnelTypeTunnel type (manual/isatap/6to4/...).rw IANAtunnelType (IANAifType-MIB) .1.3.6.1.4.1.89.129.15.1.3 |
rlIpv6TunnelToIPv6AddressThe address used for this tunnel. Could be local IPv4 of the tunnel.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.89.129.15.1.4 |
rlIpv6TunnelToIPv6PrefixLengthThe address/prefix length used for above address if applicable.rw Unsigned32 .1.3.6.1.4.1.89.129.15.1.5 |
rlIpv6TunnelToIPv6MtuMtu of this interface. Used for host isatap tunnelsrw Unsigned32 .1.3.6.1.4.1.89.129.15.1.6 |
rlIpv6TunnelToIPv6MinRtrSolicitationIntervalMinimal router solicitation interval. Used for host isatap tunnelsrw Unsigned32 .1.3.6.1.4.1.89.129.15.1.7 |
rlIpv6TunnelToIPv6LinkLayerIPv4IPv4 address used for link-layer of ipv6 over ipv4 tunnelrw IpAddress .1.3.6.1.4.1.89.129.15.1.8 |