CXMLPPP-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CXMLPPP-MIB.
78
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
78 total| Object Name |
|---|
RFC1155-SMIDetermines the number of small size buffers that you want to create for
the MLPPP stack.
Range of Values: The maximum value of this object depends on the amount of
RAM available on the system.
Default Value: 1
WARNING: When PPP ports are used, this value must be greater than 50.
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.1 |
mlpppSmallBufSizeWARNING: Do not modify this object without the supervision of Memotec
personnel.
Determines the size, in bytes, of each small buffer in the MLPPP stack.
Range of Values: 1 to 65535
Note: The maximum value of this object depends on the amount of RAM
available on the system.
Default Value: 128
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.2 |
mlpppNbLargeBufsDetermines the number of large size buffers for the MLPPP stack.
Range of Values: The maximum value of this object depends on the amount of
RAM available on the system.
Default Value: 1
WARNING: When PPP ports are used, this value must be greater than 25
because the PPP module cannot use global buffers that were defined with
OsParam.
You must decrease the OsParam small buffer parameter (cxOsNbSmallBufs)
when you increase this value or you may run out of memory, and the
system may crash.
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.3 |
mlpppLargeBufSizeDo not modify this object without the supervision of Memotec personnel.
Determines the size, in bytes, of each large size buffer of the MLPPP
stack.
Range of Values: 1 - 65535
Note: The setting of this object depends on the amount of RAM available on
the system, and should be set to the same value as the Operating System
large buffer size (cxOsNbLargeBufs).
Default Value: 1600.
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.4 |
mlpppSoftwareVersionIdentifies the Multilink Protocol software revision number, which is
displayed as a string of two numbers, each separated by a period (1.2).
The two numbers represent:
- (1) main version number
- (2) main revision number
Default Value: 1.00ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.495.2.1.6.49.40 |
mlpppNbActiveUSapIndicates the number of MLPPP upper SAPs that have been initialized.
Upper SAPs are used to interact with the network layer. Up to ten
Multilink PPP links are supported in this release.
Range of Values: 0 - 100
Default Value: nonero INTEGER .1.3.6.1.4.1.495.2.1.6.49.41 |
mlpppNbActiveLSapIndicates the number of MLPPP lower SAPs that have been initialized. Each
lower SAP has an associated PPP link. Up to ten PPP links are supported in
this release.
Range of Values: 0 - 100
Default Value: nonero INTEGER .1.3.6.1.4.1.495.2.1.6.49.42 |
mlpppNbActiveBundleIndicates the number of bundles that have been initialized. A bundle is a
group of physical links that Multilink PPP uses as one virtual link. The
network layer recognizes the bundle as a single link.
Range of Values: 0 - 100
Default Value: nonero INTEGER .1.3.6.1.4.1.495.2.1.6.49.43 |
mlpppNbSmallBufsFreeDisplays the number of small buffers that are currently free within the
MLPPP stack.
Default Value: nonero INTEGER .1.3.6.1.4.1.495.2.1.6.49.44 |
mlpppNbLargeBufsFreeDisplays the number of large buffers that are currently free within the
MLPPP stack.
Default Value: nonero INTEGER .1.3.6.1.4.1.495.2.1.6.49.45 |
mlpppMibLevelUsed to determine current MIB module release supported
by the agent. Object is in decimal.ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.49 |
mlpppLSapTableThe SAP table contains configuration information for each MLPPP layer
lower SAP (service access point).
Lower SAPs exist at the lower interface of the Multilink PPP layer and
have an associated PPP link. This PPP link attaches to the Upper SAPs of
one of three types of physical layers: Sync, Async, or console.
Note: ISDN is not supported in this release. SEQUENCE OF MlpppLSapEntry .1.3.6.1.4.1.495.2.1.6.49.50 |
mlpppLSapEntryDefines a row in the mlppLSapTable. Each row contains the objects which
define a lower service access point. MlpppLSapEntry .1.3.6.1.4.1.495.2.1.6.49.50.1 |
mlpppLSapNumberIdentifies the lower SAP entry with a unique numerical value.
Range of Values: 1 - 100
Default Value: nonero SapIndex .1.3.6.1.4.1.495.2.1.6.49.50.1.1 |
mlpppLSapRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table, but values are still in effect
until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: invalid (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.2 |
mlpppLSapAliasIdentifies this lower service access point by a textual name. Names must
be unique across all service access points at all layers.
Range of Values: 0 to16 alphanumeric characters
(first character must be a letter)
Default Value: none
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.49.50.1.3 |
mlpppLSapCompanionAliasDetermines the sub-layer SAP that this SAP communicates with. This object
contains the textual name of the sub-layer SAP.
Range of Values: 0 to16 alphanumeric characters (first character must be a
letter)
Default Value: none
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.49.50.1.4 |
mlpppLSapDialEntryThis object is supported in this release.
Determines the index in the dial table which corresponds to a ISDN
directory entry..
The access point is the B Channel Manager Directory Table entry that
corresponds to the ISDN telephone number.
This object is meaningful only if object mlpppLSapPhysicalType is set to
'isdn'.
Default Value: 0
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.12 |
mlpppLSapLcInitialMRUDetermines the Maximum Receive Unit (in octets) proposed by the local
port. The local port's proposed MRU will be negotiated with the remote
port's proposed MRU; the result of the negotiation is displayed in
mlpppLSapLsLocalMRU on the mlpppLSapLsTable table.
The MRU is the maximum length of the Information field, including Padding.
The length of the Protocol field is not included in the MRU.
If this value is set to 0, then no negotiation will occur with the remote
and the default MRU of 1500 octets is used.
If this value is not 0, then the local PPP link will negotiate for this
value with the remote peer.
Range of Values: 0 to 2048
Default Value: 1500
Related Objects:
mlpppLSapLsLocalMRU
mlpppLSapLsTable
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.14 |
mlpppLSapLcTransmitACCMapDetermines the Asynchronous Control Character Map (ACC) that the local
PPP link proposes for use on its transmit side. The local's proposed ACC
will be negotiated with the remote's proposed ACC. The result of the
negotiation is displayed in mlpppLSapLsPeerToLocalACCMap in the
mlpppLSapLsTable.
The ACCMap maps the first 32 ASCII control characters (numbered 0 to 31).
The map allows datagrams traveling over a PPP link to be transparent to
all intermediate devices such as modems.
The value of the object is a string of four octets. This string totals 32
bits, and position numbers (0-31) correspond to the first 32 control
characters. For example, if bit 19 is set to 1, then the ASCII control
character 19 (ctrl-s) is sent transparently.
Note: Async Control Character Map must be cleared when Multilink is used (value:
00 00 00 00)
Range of Values: 4 octets, each character ranging from 00 to FF.
Default Value: FFFFFFFF.
Configuration Changed: administrativerw DisplayString .1.3.6.1.4.1.495.2.1.6.49.50.1.15 |
mlpppLSapLcMaxConfigureDetermines the maximum number of Configure-Request packets that the port
can send without any acknowledgment from the peer. If the maximum number
of packets has been sent and there is still no response from the other end
of the link, the Link Control Protocol (LCP) assumes that the peer is
unable to respond and that the link cannot be established.
Range of Values: 1-15
Default Value: 10
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.16 |
mlpppLSapLcMaxTerminateDetermines the maximum number of Termination-Request packets that the
port can send without any answer from the peer.
If the maximum number of packets has been sent and there is still no
response from the other end of the link, the Link Control Protocol (LCP)
assumes that the peer is unable to respond. The link is closed without
negociating the termination.
Range of Values: 1-5
Default Value: 2
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.17 |
mlpppLSapLcMaxFailureDetermines the maximum number of Configure-Not-Acknowledge packets which
can be sent without receipt of a Configure-Acknowledge packet.
A Configure-Acknowledge packet means that one end of the link accepts the
value for the configuration parameter proposed by the peer.
A Configure-Not-Acknowledge packet means that the peer does not accept the
proposal. If the maximum number is exceeded, the link is closed down. This
prevents endless loops in the configuration process.
Range of Values: 1 to 15
Default Value: 5
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.18 |
mlpppLSapLcRestartTimerDetermines the time interval (in seconds) between the sending of a
Configure-Request or Terminate-Request packet, and the time before its
retransmission if no acknowledgment is received.
The packet is retransmitted up to the maximum number permitted in
mlpppUSapLcMaxConfigure of this table.
Default Value: 3
Range of Values: 1 to 100
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.19 |
mlpppLSapLcProtFieldCompDetermines whether the local PPP port can receive packets with a
compressed PPP Protocol Field. If enabled, the port informs its peer that
it can receive packets with a compressed PPP Protocol Field (when the
configuration of the PPP link is negotiated).
Note: Protocol Field Compression must be enabled when Multilink is used.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.20 |
mlpppLSapLcACFieldCompDetermines whether the local PPP port can receive packets with compressed
PPP Address and Control Fields. If enabled, the port informs its peer that
it can receive packets with a compressed PPP Address and Control Field
when the configuration of the PPP link is negotiated.
Note: Address and Control Field Compression must be enabled when Multilink is
used.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.21 |
mlpppLSapLcMagicNumberDetermines whether the Magic Number is enabled or disabled.
The Magic Number is a unique random system generated number, present in
every Configure-Request packet. The Magic Number is used to ensure that
the same packet is not sent back and forth between the local and the
remote in an endless loop.
If the Magic Number is enabled, then the local end of the link will check
the Magic Number in each Configure-Request packet it receives. If the
number is the same as its own, it will change its number and send a
NoAcknowledge packet back to the remote. If the local end of the link
continues to receive Configure-Requests with its own number, it assumes a
loopback. After the number of Configure-Requests specified in
mlpppUSapLcMaxConfigure of this table has been exceeded, the link will go
down.
Note:
Magic Number must be disabled when Multilink is used.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.22 |
mlpppLSapLinkControlEnables/disables the connectivity of this link to the bundle
Stops or starts the interface
Acts also as an operational control.
Options:
enabled :the link may connect to the bundle
disabled :the link may not connect to the bundle
Default Value: enabledrw Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.23 |
mlpppLSapClearStatsClears the statistics counter of the PPP link associated to this lower SAP.
Options:
clearStats :clears statistics
Default Value: nonerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.30 |
mlpppLSapStateIndicates the current state of this lower SAP (service access point).
Options:
not-used (1): SAP not in use.
unbound (2): SAP not bound to another software layer.
bound (3): SAP bound to another software layer.
Default Value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.40 |
mlpppLSapPhysNetStatusIndicates the most recent change in link status between MLPPP and the
physical layer.
Options:
pif-attached (1): A physical interface has been attached to this lower SAP.
pif-detached (2): A physical interface has been detached from this lower SAP.
Default Value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.41 |
mlpppLSapVirtNetStatusIndicates the most recent change in link status between MLPPP and the
network layer.
Each lower SAP has an associated PPP link.
Options:
vif-attached (1): The PPP link has been attached to a bundle.
vif-detached (2): The PPP link has been detached from a bundle.
vif-up (3): The PPP link went up.
vif-down (4): The PPP link went down.
vif-finished (5): The PPP link is finished
Default Value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.42 |
mlpppLSapLsBadAddressesIdentifies the number of packets received at the local port which contain
a bad address field.
Range of Values: 0 - 4,294,967,295
Default Value: Nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.43 |
mlpppLSapLsBadControlsIdentifies the number of packets received at the local port which contain
an incorrect control field.
Range of Values: 0 - 4,294,967,295
Default Value: Nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.44 |
mlpppLSapLsPacketTooLongsIdentifies the number of packets received at the local port which have
been discarded because their length exceeded the Maximum Receive Unit
(MRU). Packets which are longer than the MRU but which are successfully
received and processed are not included in this count.
The MRU is the maximum length of the Information field, including Padding.
The length of the Protocol field is not included in the MRU.
Range of Values: 0 - 4,294,967,295
Default Value: Nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.45 |
mlpppLSapLsBadFCSsIdentifies the number of packets received at the local port which have
been discarded because they had an incorrect Frame Check Sequence (FCS).
Range of Values: 0 - 4,294,967,295
Default Value: nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.46 |
mlpppLSapLsLocalMRUIdentifies the current value in octets of the Maximum Receive Unit (MRU)
for the local PPP link.
This value is the MRU that the remote is using to send packets over the
PPP link. The value is meaningful only when the link has reached the open
state (virtNetStatus is up).
Range of Values: 1 - 2048
Default Value: 1500ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.47 |
mlpppLSapLsRemoteMRUIdentifies the current value in octets of the Maximum Receive Unit (MRU)
for the remote PPP link.
This value is the MRU that the local is using to send packets over the PPP
link. The value is meaningful only when the link has reached the open
state (virtNetStatus is up).
Range of Values: 1 - 2048
Default Value: 1500ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.48 |
mlpppLSapLsLocalToPeerACCMapIdentifies the current value of the Asynchronous Control
Character(ACC)Map for the local PPP link. This value is the ACCMap that
the local link is using to send packets over the PPP link.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Range of Values: 4 octets, each character in the range 00 to FF
Default Value: FF FF FF FFro DisplayString .1.3.6.1.4.1.495.2.1.6.49.50.1.49 |
mlpppLSapLsPeerToLocalACCMapIdentifies the current value of the Asynchronous Control Character(ACC) Map
for the remote PPP link. This value is the ACCMap that the remote peer is using
to send packets over the PPP link.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Range of Values: 4 octets, each character in the range 00 to FF
Default Value: FF FF FF FFro DisplayString .1.3.6.1.4.1.495.2.1.6.49.50.1.50 |
mlpppLSapLsLocalToRemoteProtCompIndicates whether the local PPP link is using Protocol Compression when
transmitting packets to the remote.
This value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.51 |
mlpppLSapLsRemoteToLocalProtCompIndicates whether the remote PPP link is using Protocol Compression when
transmitting packets to the local.
This value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of
the PPP negotiation.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.52 |
mlpppLSapLsLocalToRemoteACCompIndicates whether the local end of the PPP link is using Address and
Control Compression when it transmits packets to the remote.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.53 |
mlpppLSapLsRemoteToLocalACCompIndicates whether or not the remote end of the PPP link is using Address
and Control Compression when it transmits packets to the local.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.50.1.54 |
mlpppLSapNbBytesSentIndicates the number of bytes sent to the physical layer through this
lower SAP since system startup or since last statistics reset.
Range of Values: 0 - 4,294,967,295
Default Value: nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.70 |
mlpppLSapNbBytesReceivedIndicates the number of bytes received from the physical layer through
this lower SAP since system startup, or since last statistics reset.
Range of Values: 0 - 4,294,967,295
Default Value: nonero Counter .1.3.6.1.4.1.495.2.1.6.49.50.1.71 |
mlpppLSapLinkUSapNumberDetermines the MLPPP upper SAP number that is associated with this MLPPP
lower SAP.
In this release, bundling is not supported, and the MLPPP upper SAP number
should be unique within all lower SAPs.
-
PPP links that use the same upper SAP number are bundled, and appear as a
single link to the network layer.
-
Note: If this value is 0, then this lower SAP will not be used and its
link will not be bundled.
Range of Values: 0 - 100
Default Value: 0
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.50.1.100 |
mlpppUSapTableThe SAP table contains configuration information for each MLPPP layer
upper SAP (service access point).
Upper SAPs exist at the upper interface of the Multilink PPP layer, and
are seen as the MLPPP data links by the network layers. SEQUENCE OF MlpppUSapEntry .1.3.6.1.4.1.495.2.1.6.49.51 |
mlpppUSapEntryDefines a row in the mlppUSapTable. Each row contains the objects which
define an upper service access point. MlpppUSapEntry .1.3.6.1.4.1.495.2.1.6.49.51.1 |
mlpppUSapNumberIdentifies the upper SAP entry with a unique numerical value.
Range of Values: 1 - 100
Default Value: nonero SapIndex .1.3.6.1.4.1.495.2.1.6.49.51.1.1 |
mlpppUSapRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): Row is deleted from the table, but values are still in effect
until the next reset.
valid (2): Use this value to add a new row to the table, or modify an
existing row.
Default Value: invalid (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.2 |
mlpppUSapAliasIdentifies this upper service access point by a textual name. Names must
be unique across all service access points at all layers.
Range of Values: 0 - 16 alphanumeric characters
(first character must be a letter)
Default Value: none
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.49.51.1.3 |
mlpppUSapLcInitialMRRUThis object is not implemented in this release.
Determines the Maximum Receive Reconstructed Unit (MRRU) in octets
proposed by the local port. The local port's proposed MRRU is negotiated
with the remote port's proposed MRRU. The result of the negotiation is
displayed in mlpppLSapLsLocalMRRU on the mlpppLSapLsTable table.
If this value is 0, then no negotiation will occur with the remote, and
the default MRRU of 1500 octets is used; otherwise, the local PPP link
will negotiate for this value with the remote peer.
Range of Values: 0 - 2048
Default Value: 1500
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.20 |
mlpppUSapLcSeqFieldCompThis object is implemented in this release.
Determines whether the Sequence Number Field is compressed or not. If the
the Sequence Number Field is compressed, then the short sequence number
header format is used and sequence numbers are 12 bits long. If the
Sequence Number Field is not compressed, then the long sequence number
header format is used and sequence numbers are 24 bits long.
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.21 |
mlpppUSapLcUseBACPIf enabled, BACP is used for adding/removing links
Options:
enabled (1)
disabled (2)
Default Value: disabled (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.22 |
mlpppUSapTransmitWindowDetermines the size of the transmit window for this SAP, i.e. the maximum number
of buffers queued by MLPPP before it starts to discard frames
Range of Values: 1 - 255
Default Value: 255
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.23 |
mlpppUSapGeneratorDetermines whether this SAP generates for diagnostic purposes the number
of frames set by object mlpppUSapGeneratorNumberOfFrames of a size set in
'mlpppUSapGeneratorFrameSize'.
Options:
disabled (1): frame generator is disabled .
enabled (2): frame generator is enabled after a system reset to generate a
sequence of frames.
enabledos(3): frame generator is enabled after a system reset to generate a
sequence of frames.The fragments are sent out-of-sequence.
retrigger(4): frame generator is enabled immediately to generate a sequence
of frames.
Default Value: disabled
Configuration Changed: operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.24 |
mlpppUSapGeneratorLinkUSapIdentifies the upper SAP entry to which all received generator frames
are sent If 0, the received frames are discarded.
Range of Values: 0 - 100
Default Value: 0
Configuration Changed: operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.25 |
mlpppUSapGeneratorFrameSizeDetermines the size of each frame generated for this SAP.
Range of Values: 32 - 4096
Default Value: 32
Configuration Changed: operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.26 |
mlpppUSapGeneratorNumberOfFramesDetermines the number of frames to be generated for this SAP.
Range of Values: 1 - 200 (200=continuous)
Default Value: 1
Configuration Changed: operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.27 |
mlpppUSapGeneratorInterFrameDelayDetermines the time in milliseconds that must pass between frames
generated for this SAP.
Range of Values: 50 - 60,000
Default Value: 50
Configuration Changed: operativerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.28 |
mlpppUSapGeneratorFramePriorityDetermines the priority of SAP generator frames for diagnostic purposes
Options:
lowpri (1): low priority.
medpri (2): medium priority
highpri (3): high priority
veryhighpri (4): very high priority
Default Value: lowpri
Configuration Changed: operativerw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.29 |
mlpppUSapClearStatsClears the statistics counter of the MLPPP link associated with this
upper SAP.
Options:
clearStats : clears statistics
Default Value: nonerw INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.30 |
mlpppUSapMlpppModeIndicates the current use of this upper SAP. If MLPPP is to be used
for inverse multiplexing, it must be enabled. If disabled, dumb inverse
multiplexing and load balancing is done
Options:
enabled (1) : MLPPP is used
disabled (2) : dumb inverse multiplexing / load balancing
Default Value: enabledrw Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.31 |
mlpppUSapStateIndicates the current state of this upper SAP.
Options:
not-used (1): SAP not in use
unbound (2): SAP not bound to another software layer
bound (3): SAP bound to another software layer
Default Value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.40 |
mlpppUSapNbPPPLinkIndicates the number of MLPPP lower SAPs that are associated to this
upper MLPPP SAP.
This value is equivalent to the number of PPP links that are bundled into
one MLPPP link at this upper SAP.
Range of Values: 0 to 100
Default Value: 0ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.41 |
mlpppUSapLsLocalMRRUThis object is implemented in this release.
Identifies the current value in octets of the Maximum Receive Reconstructed
Unit (MRRU) for the local bundle. This value is the MRRU that the remote
is using to send packets over the MLPPP link.
The MRRU is the maximum number of bytes that a reconstructed (unbundled)
PPP packet can contain.
This value is meaningful only when the link has reached the
open state (virtNetStatus is up); at which time it displays the result of
the PPP negotiation.
Range of Values: 1 to 2048
Default Value: 1500ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.42 |
mlpppUSapLsRemoteMRRUThis object is implemented in this release.
Identifies the current value in octets of the Maximum Receive
Reconstructed Unit (MRRU) for the remote bundle. This value is the MRRU
that the local is using to send packets over the MLPPP link.
The MRRU is the maximum number of bytes that a reconstructed (unbundled)
PPP packet can contain.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Range of Values: 1 to 2048
Default Value: 1500ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.43 |
mlpppUSapLsLocalToRemoteSeqFieldCompThis object is implemented in this release.
Indicates whether the local end of the MLPPP link is using short sequence
field (12 bits) when it transmits packets to the remote.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Options:
enabled (1)
disabled (2)
Default Value: enabled (1)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.44 |
mlpppUSapLsRemoteToLocalSeqFieldCompThis object is implemented in this release.
Indicates whether the remote end of the MLPPP link is using short sequence
field (12 bits) when it transmits packets to the local.
The value is meaningful only when the link has reached the open state
(virtNetStatus is up); at which time it displays the result of the PPP
negotiation.
Options:
enabled (1)
disabled (2)
Default Value: enabled (1)ro Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.45 |
mlpppUSapNbPPPLinkUPThe number of PPP links in a bundle which succesfully finished the LCP
configuration phase. The PPP layer is UP on that many links of the bundle.ro INTEGER .1.3.6.1.4.1.495.2.1.6.49.51.1.46 |
mlpppUsapMlpNcpStateThe state of the NCP associated with the MLPPP protocol. The bundle can
talk MLPPP only after the MRRU option has been succesfully negociated.
Options:
ncp-up (1) : the NCP state is up
ncp-down (2) : the NCP state is down
ncp-na (3) : the NCP state is not available
Default value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.47 |
mlpppUsapGenNcpStateThe state of the NCP associated with the MLPPP frame generator PID. The
generator can be used only after two bundles have negociated the use of
a specific PID for the generated frames. The protocol ID for the MLPPP
frame generator is MEMOTEC proprietary and it's default value is 0xcf
and it's NCP is using by default 0x80cf.
Options:
ncp-up (1) : the NCP state is up
ncp-down (2) : the NCP state is down
ncp-na (3) : the NCP state is not available
Default value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.48 |
mlpppUsapBapNcpStateThe state of the NCP associated with the BAP protocol. The BAP protocol
can be used only after two bundles have negociated it's use for adding or
removing links to the bundles.
Options:
ncp-up (1) : the NCP state is up
ncp-down (2) : the NCP state is down
ncp-na (3) : the NCP state is not available
Default value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.49 |
mlpppUsapFrNcpStateThe state of the NCP associated with the FR protocol. The FR protocol
can be used over MLPPP only after two bundles have negociated the FRNCP
configuration. The protocol ID for FR over MLPPP is MEMOTEC proprietary
and it's default value is 0xcd and for it's NCP 0x80cd.
Options:
ncp-up (1) : the NCP state is up
ncp-down (2) : the NCP state is down
ncp-na (3) : the NCP state is not available
Default value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.50 |
mlpppUsapIpNcpStateThe state of the NCP associated with the IP protocol. The IP protocol
can be used over MLPPP only after two bundles have negociated the IPNCP
configuration.
Options:
ncp-up (1) : the NCP state is up
ncp-down (2) : the NCP state is down
ncp-na (3) : the NCP state is not available
Default value: nonero Enumeration .1.3.6.1.4.1.495.2.1.6.49.51.1.51 |
mlpppUSapNbBytesSentIndicates the number of bytes sent to the network layer through this
upper SAP since system startup, or since last statistics reset.
Range of Values: 0 - 4,294,967,295
Default Value: nonero Counter .1.3.6.1.4.1.495.2.1.6.49.51.1.70 |
mlpppUSapNbBytesReceivedIndicates the number of bytes received from the network layer through
this upper SAP since system startup, or since last statistics reset.
Range of Values: 0 - 4,294,967,295
Default Value: nonero Counter .1.3.6.1.4.1.495.2.1.6.49.51.1.71 |