CTRON-ISDN-CONFIGURATION-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CTRON-ISDN-CONFIGURATION-MIB.
67
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
cabletron OBJECT IDENTIFIER .1.3.6.1.4.1.52 |
RFC1155-SMI Unknown .1.3.6.1.4.1.52 |
mibs OBJECT IDENTIFIER .1.3.6.1.4.1.52.4 |
ctron OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1 |
ctDataLink OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1.2 |
ctronWan OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1.2.7 |
ctISDNconfigMib OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1.2.7.4 |
ctISDNcontrol OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1.2.7.4.1 |
isdnDchTableA list of D channnel interfaces entries. The list consists
of a single entry at this time. SEQUENCE OF IsdnDchEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.1 |
isdnDchEntryA D channnel interface entry containing objects relating to
the particular D channel. IsdnDchEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1 |
isdnDchIndexA unique index for this D Channel of this ISDN-Controller.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.1 |
isdnDchRateAccessThe Rate Access of this ISDN interface.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.2 |
isdnDchAllowedChA bit string with bit 1 signifiying time slot 1. A set
bit means that a B channel may be allocated on that time slot.
A reset bit means the channel is reserved or otherwise out of service.ro INTEGER -- BIT STRING {1..32} .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.3 |
isdnDchChInUseA bit string with bit 1 signifying time slot 1. A set
bit means that a B channel has been allocated on that time slot.
A reset bit means the channel is available, reserved, or otherwise
out of service.ro INTEGER -- BIT STRING {1..32} .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.4 |
isdnDchSupportedSwitchesA bit string with each bit position signifying support of
a specific switch type as indicated by the list. A set bit means
that that switch type is supported.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.5 |
isdnDchSwitchTypeSwitch type selector as indicated by the list.rw Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.6 |
isdnDchSPID1The Service profile identifier for BRI channel 1.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.7 |
isdnDchSPID2The Service profile identifier for BRI channel 2.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.8 |
isdnDchDirNum1The local directory number for BRI channel 1.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.9 |
isdnDchDirNum2The local directory number for BRI channel 2.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.10 |
isdnDchOperStatusThe operational status of the signalling channel.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.1.1.11 |
dialCtlNbrCfgTableThe list of neighbors from which the managed device
will accept calls or to which it will place them. SEQUENCE OF DialCtlNbrCfgEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.2 |
dialCtlNbrCfgEntryA single Neighbor. This entry is effectively permanent,
and contains address information describing the neighbor.
The value of dialCtlNbrCfgOriginateAddress must be
specified before a new row in this table can become
active(1). Any writeable parameters in an existing entry
can be modified while the entry is active. The modification
will take effect when the neighbor in question will be
called the next time. DialCtlNbrCfgEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1 |
dialCtlNbrCfgIdThis object defines a single neighbor. There may
be several entries in this table for one neighbor,
defining different ways of reaching this neighbor.
Thus, there may be several entries in this table
with the same value of dialCtlNbrCfgId.
Multiple entries for one neighbor may be used to support
multilink as well as backup lines. A single neighbor
will be identified by a unique value of this object.
Several entries for one neighbor MUST have the same
value of dialCtlNbrCfgId and dialCtlNbrCfgIfIndex
but still different ifEntries and thus different
values of dialCtlNbrCfgIndex.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.1 |
dialCtlNbrCfgIndexThe index value which uniquely identifies an entry
in this table.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.2 |
dialCtlNbrCfgIfIndexThe ifIndex value of the interface associated with this
neighbor.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.3 |
dialCtlNbrCfgOriginateAddressCall Address at which the neighbor will be called.
Think of this as the set of characters following 'ATDT '
or the 'phone number' included in a D channel call request.
The structure of this information will be switch type
specific.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.4 |
dialCtlNbrCfgAnswerAddressCalling Party Number information element, as for example
passed in an ISDN SETUP message by a PBX or switch,
for incoming calls. This address can be used to identify
the neighbor. If this address is either unknown or identical
to dialCtlNbrCfgOriginateAddress, this object will be a zero
length string.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.1.2.7.4.1.2.1.5 |
rmtProfileTableThe list of neighbors from which this device will accept calls or
to which it will place them. SEQUENCE OF RmtProfileEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.3 |
rmtProfileEntryA single Neighbor. This entry is effectively permanent, and contains
information describing the neighbor. RmtProfileEntry .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1 |
rmtProfileEntryIndexThe index value which uniquely identifies an entry
in this table.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.1 |
rmtProfileEntryNameASCII name of the neighbor.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.2 |
rmtProfileEntryMakerNameASCII name of the manufacturer of the neighbor. In other
words, it is a name by which to uniquely identify the remote
access device to which the profile belongs.rw OCTET STRING .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.3 |
rmtProfileEntryActionDesired action for the neighbor interfacerw Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.4 |
rmtProfileEntryStateCurrent state of the neighbor interfacero Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.5 |
rmtProfileEntryMaxNeighborThe maximum allowable dialCtlNbrCfgIndex. It is the number
of instances of the profile.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.6 |
rmtProfileEntryBchInUseA bit string with bit 1 signifiying B channel 1. A set
bit means that this channel was assigned for current or
last call.ro INTEGER -- BIT STRING { 1...32 } .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.7 |
rmtProfileEntryLinkHeadA zero value signifies it is a primary profile. Otherwise, it is an
instance profile and the value identifies the primary profile from
which it was spawned.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.8 |
rmtProfileEntryNextLinkA non-zero value identifies an instance profile. Whereas, a zero
value either means it is a primary profile or the last instance
of a primary profile.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.9 |
rmtProfileEntryMpCapableMP option selector. Set to a value of one when MP support is
desired otherwise set to a value of two. The default setting is
disabled. When enabled the attempt is made to negotiate MP support.
Both parties must support MP to be able to successfully negotiate
MP.rw Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.10 |
rmtProfileEntryMpLineUtilizationUsed to set the Line Utilization Threshold (LUT) % to compare
against the linear weighted percentage to determine when
more/less bandwidth is to be added/removed. Linear weighting
is computed (averaged) over the period of time specified by
the rmtProfileEntryMpHistoryTime object. Additional bandwidth
is added whenever the linear weighted percentage exceeds the
LUT % for a consecutive number of average line utilization
reading(s) (computation(s)) as specified by the
rmtProfileEntryMpMoreBWSamples object. Conversely,
additional possible previously added Bandwidth is removed
whenever the linear weighted percentage falls below the LUT %
value for a consecutive number of average line utilization
reading(s) (computation(s)) as specified by the
rmtProfileEntryMpLessBWSamples object.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.11 |
rmtProfileEntryMpHistoryTimeUsed to set the history time value in seconds for the number of line
utilization reading(s)/sample(s) desired to compute the average
line utilization. It specifies the window size over which to
to compute the average line utilization.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.12 |
rmtProfileEntryMpMoreBWSamplesUsed to set the number of consecutive line utilization average
computations that must exceed the LUT % value as specified by the
rmtProfileEntryMpLineUtilization object before allowing possible
more bandwidth to be added.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.13 |
rmtProfileEntryMpLessBWSamplesUsed to set the number of consecutive line utilization average
computations that must fall below the LUT % value as specified by the
rmtProfileEntryMpLineUtilization object before removing possible
previously added bandwidth.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.14 |
rmtProfileEntryMpMaxCallsAllowedUsed to set the maxium number of channels an ISDN MP capable
call is allowed.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.15 |
rmtProfileEntryMpCallsToAddUsed to set the number of additional channel(s) (call(s)) to
increment by whenever the need for more bandwidth is determined.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.16 |
rmtProfileEntryMpCallsToRemoveUsed to set the number of channel(s) (call(s)) to decrement
by whenever the need for possible previously added additional
bandwidth is determined to no longer be needed/desired.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.17 |
rmtProfileEntryMpAvgPktSizeUsed to set the average packet size by which to determine when
its best to split a packet. This is an attempt to minimize the
amount of buffering necessary at the remote device to maintain
packet sequentiality.rw INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.18 |
rmtProfileEntryMpRmtBwCtrlMP remote bandwidth control selector. Set to a one when
bandwidth changes are permitted by either side ie by both
parties otherwise set to a value of two. The default setting
is disabled. That is to say, only the caller is permitted
to change (control) the bandwidth.rw Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.1.3.1.19 |
callHistory OBJECT IDENTIFIER .1.3.6.1.4.1.52.4.1.2.7.4.2 |
callHistoryTableMaxLengthThe upper limit on the number of entries that the
callHistoryTable may contain. When this table is full,
the oldest entry will be deleted and the new one will
be created.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.1 |
callHistoryTableA table containing information about specific
calls to a specific destination. SEQUENCE OF CallHistoryEntry .1.3.6.1.4.1.52.4.1.2.7.4.2.2 |
callHistoryEntryThe information regarding a single Connection. CallHistoryEntry .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1 |
callHistorySetupTimeThe value of system up time when the call associated to this
entry was started. This will be useful for an NMS to
retrieve all calls after a specific time. Also, this object
can be useful in finding large delays between the time the
call was started and the time the call was connected.
For ISDN media, this will be the time when the setup
message was received from or sent to the network.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.1 |
callHistoryIndexIndex variable to access the CallHistoryEntry objects
of the callHistoryTable.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.2 |
callHistoryPeerAddressThe number this call is connected to. If the number is
not available, then it will have a length of zero.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.3 |
callHistoryNeighborIdThis is the Id value of the neighbor table entry
to which this call was made. If a neighbor table entry
for this call does not exist, the value of this object
will be zero.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.4 |
callHistoryLogicalIfIndexThis is the ifIndex value of the logical interface through
which this call was made.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.5 |
callHistoryDisconnectCauseThe encoded network cause value associated with this call.
The value of this object will depend on the interface type
as well as on the protocol and protocol version being
used on this interface. The more common cause values are
indicated in the list.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.6 |
callHistoryConnectTimeThe value of system up time when the call was connected.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.7 |
callHistoryDisconnectTimeThe value of system up time when the call was disconnected.ro INTEGER .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.8 |
callHistoryCallOriginThe call origin.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.9 |
callHistoryInfoTypeThe information type for this call.ro Enumeration .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.10 |
callHistoryTransmitPacketsThe number of packets which were transmitted while this
call was active.ro Counter .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.11 |
callHistoryTransmitBytesThe number of bytes which were transmitted while this
call was active.ro Counter .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.12 |
callHistoryReceivePacketsThe number of packets which were received while this
call was active.ro Counter .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.13 |
callHistoryReceiveBytesThe number of bytes which were received while this
call was active.ro Counter .1.3.6.1.4.1.52.4.1.2.7.4.2.2.1.14 |