CTELS100-NG-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CTELS100-NG-MIB.
70
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
70 total| Object Name |
|---|
mib-2 OBJECT IDENTIFIER .1.3.6.1.2.1 |
RFC1213-MIB Unknown .1.3.6.1.2.1 |
cabletron OBJECT IDENTIFIER .1.3.6.1.4.1.52 |
els100 OBJECT IDENTIFIER .1.3.6.1.4.1.52.1011 |
els100SystemConfig OBJECT IDENTIFIER .1.3.6.1.4.1.52.1011.1 |
els100SysSerialnoThe serial number of the system.ro DisplayString .1.3.6.1.4.1.52.1011.1.1 |
els100SysTftpIPAddressThe IP address of the TFTP server from which a software
download is to be initiated. This variable must be set
before a TFTP download can be started with the
els100SysTftpStartDownload variable.rw NetworkAddress .1.3.6.1.4.1.52.1011.1.2 |
els100SysTftpFilenameThe name of the software upgrade file residing on the
TFTP server. Path information must be included in the file
name. This variable must be set before a TFTP download can
be started with the els100SysTftpStartDownload variable.rw DisplayString .1.3.6.1.4.1.52.1011.1.3 |
els100SysPowerupCountThe total number of times the system has powered up since
it was shipped from the factory.ro INTEGER .1.3.6.1.4.1.52.1011.1.4 |
els100SysBrcastCutoffRateThe Broadcast Cutoff Rate of the switch allowing for the
control of broadcast storms. The value of this variable sets
a per second rate. If the broadcast and unknown destination
address frames being forwarded through the system surpass this
rate, they are dropped. Valid values for this parameter are
in the range (100..500000).rw INTEGER .1.3.6.1.4.1.52.1011.1.5 |
els100SysGatewayIPAddressThe IP address of the next hop router (gateway) to which
frames destined for an IP subnet different than what the
system resides are sent.rw NetworkAddress .1.3.6.1.4.1.52.1011.1.6 |
els100SysTftpStartDownloadStart a TFTP download. A SET of this variable with the
value download (1) initiates a TFTP download to upgrade the
system software. The variables els100SysTftpIPAddress and
els100SysTftpFilename must be configured before a download
can begin. A GET of this variable will always return the
value noDownload (2).rw Enumeration .1.3.6.1.4.1.52.1011.1.7 |
els100SysBootPDhcpEnableEnable or disable the operation of the BootP and DHCP
protocols on the system. These protocols are used for
automatically configuring the system's IP address
information if a properly configured BootP and/or DHCP
server exists on the network.rw Enumeration .1.3.6.1.4.1.52.1011.1.8 |
els100SysResetInitiate a software reset of the system.rw Enumeration .1.3.6.1.4.1.52.1011.1.10 |
els100SysSyslogServerThe IP address of the Syslog Server.rw NetworkAddress .1.3.6.1.4.1.52.1011.1.11 |
els100SysLowestSyslogSeverityThe Lowest Syslog Severity Level. All logs with
the same or higher severity will be delivered.
Note: higher severity has lower number.rw Enumeration .1.3.6.1.4.1.52.1011.1.12 |
els100SysComPortEnableThe administrative state of the Com Port.rw Enumeration .1.3.6.1.4.1.52.1011.1.13 |
els100SysBoardIDThe system board ID.ro INTEGER .1.3.6.1.4.1.52.1011.1.14 |
els100PortTableThe port table. SEQUENCE OF Els100PortEntry .1.3.6.1.4.1.52.1011.2 |
els100PortEntryAn entry in the port table. Els100PortEntry .1.3.6.1.4.1.52.1011.2.1 |
els100PortThe number of the port, from 1 to the number of ports on
the system.ro INTEGER .1.3.6.1.4.1.52.1011.2.1.1 |
els100PortStatusThe connection (link) status of the port, either up
(linked) or down (not linked).ro Enumeration .1.3.6.1.4.1.52.1011.2.1.2 |
els100PortDuplexStatusThe duplex status of the port, either half duplex or
full duplex.rw Enumeration .1.3.6.1.4.1.52.1011.2.1.3 |
els100PortForwardedFramesThe number of frames received on the port and forwarded
to another port on the system module for processing.ro Counter .1.3.6.1.4.1.52.1011.2.1.4 |
els100PortRcvdLocalFramesThe number of frames received where the destination is
on the port.ro Counter .1.3.6.1.4.1.52.1011.2.1.5 |
els100PortNameA descriptive string of up to 60 characters used by the
network administrator to name the port.rw DisplayString .1.3.6.1.4.1.52.1011.2.1.6 |
els100PortEnableThe enable status of the port, either enable or disable.rw Enumeration .1.3.6.1.4.1.52.1011.2.1.7 |
els100PortSpeedThe speed the port is operating at: 10Mbps, or
100Mbps, or 1000Mbps.rw Enumeration .1.3.6.1.4.1.52.1011.2.1.8 |
els100PortAutonegEnableThe auto-negotiation status of the port, either enable
or disable. When in the enable (2) state, the port will
automatically configure its duplex and speed operation.rw Enumeration .1.3.6.1.4.1.52.1011.2.1.9 |
els100PortFlowControlEnableThe state of flow control operation of the port, either
enable or disable.rw Enumeration .1.3.6.1.4.1.52.1011.2.1.10 |
els100PortTypePort physical interface type.ro Enumeration .1.3.6.1.4.1.52.1011.2.1.11 |
els100Switch OBJECT IDENTIFIER .1.3.6.1.4.1.52.1011.3 |
els100SwitchIPAddressThe IP address of the system.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.1 |
els100SwitchSubnetMaskThe subnet mask associated with the IP address of the system.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.2 |
els100ActiveAgingTimeThe aging time of entries in the MAC address forwarding table
of the system.rw INTEGER .1.3.6.1.4.1.52.1011.3.3 |
els100SwitchSTPStatusThe Spanning Tree status of the system, enter on or off.rw Enumeration .1.3.6.1.4.1.52.1011.3.5 |
els100SwitchManager OBJECT IDENTIFIER .1.3.6.1.4.1.52.1011.3.6 |
els100SwitchTrapRcvr1The IP address of the first SNMP manager to which traps
from the system are directed.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.6.1 |
els100SwitchTrapCommunity1The community name of the first SNMP manager to which traps
from the system are directed.rw DisplayString .1.3.6.1.4.1.52.1011.3.6.2 |
els100SwitchTrapRcvr2The IP address of the second SNMP manager to which traps
from the system are directed.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.6.3 |
els100SwitchTrapCommunity2The community name of the second SNMP manager to which traps
from the system are directed.rw DisplayString .1.3.6.1.4.1.52.1011.3.6.4 |
els100SwitchTrapRcvr3The IP address of the third SNMP manager to which traps
from the system are directed.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.6.5 |
els100SwitchTrapCommunity3The community name of the third SNMP manager to which traps
from the system are directed.rw DisplayString .1.3.6.1.4.1.52.1011.3.6.6 |
els100SwitchTrapRcvr4The IP address of the fourth SNMP manager to which traps
from the system are directed.rw NetworkAddress .1.3.6.1.4.1.52.1011.3.6.7 |
els100SwitchTrapCommunity4The community name of the fourth SNMP manager to which traps
from the system are directed.rw DisplayString .1.3.6.1.4.1.52.1011.3.6.8 |
els100SwitchPortMirroringStatusThe Port Mirroring status of the system, either disable
or enable.rw Enumeration .1.3.6.1.4.1.52.1011.3.7 |
els100SwitchMirroredPortThe port that is being mirrored - the source.rw INTEGER .1.3.6.1.4.1.52.1011.3.8 |
els100SwitchMirroringPortThe port that is mirroring - the destination.rw INTEGER .1.3.6.1.4.1.52.1011.3.9 |
els100SwitchXmitMirrorEnableEnable or disable the mirroring of transmitted traffic
out the mirrored port to the mirroring port.rw Enumeration .1.3.6.1.4.1.52.1011.3.10 |
els100SwitchRcvMirrorEnableEnable or disable the mirroring of received traffic
into the mirrored port to the mirroring port.rw Enumeration .1.3.6.1.4.1.52.1011.3.11 |
els100SwitchVlanEnableGlobally enable or disable the VLAN operation of the
system.rw Enumeration .1.3.6.1.4.1.52.1011.3.12 |
els100SwitchVlanConfigTableThe VLAN configuration table. SEQUENCE OF Els100SwitchVlanEntry .1.3.6.1.4.1.52.1011.3.13 |
els100SwitchVlanEntryAn entry in the VLAN configuration table. Els100SwitchVlanEntry .1.3.6.1.4.1.52.1011.3.13.1 |
els100SwitchVlanIdThe number of the VLAN, from 1 to the number of VLAN's
supported on the system.rw INTEGER .1.3.6.1.4.1.52.1011.3.13.1.1 |
els100SwitchVlanNameA descriptive string of up to 60 characters used by the
network administrator to name the VLAN.rw DisplayString .1.3.6.1.4.1.52.1011.3.13.1.2 |
els100SwitchVlanPortsThe set of ports in the VLAN. For systems supporting
tagged VLAN's, these are the ports to which packets
on the VLAN are sent untagged. Each octet within the
value of this object specifies a set of eight ports,
with the first octet specifying ports 1 through 8, the
second octet specifying ports 9 through 16, etc. Within
each octet, the most significant bit represents the
lowest numbered port, and the least significant bit
represents the highest numbered port. Thus each port
of the system is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the VLAN; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.52.1011.3.13.1.3 |
els100SwitchVlanEgressPortsThe set of ports defined to be on other VLAN's to which
tagged packets destined for this specific VLAN should
also be sent. Thus, this variable defines ports on the
system that reach stations downstream which are on this
VLAN and to which traffic may be forwarded. Each octet
within the value of this object specifies a set of eight
ports, with the first octet specifying ports 1 through 8,
the second octet specifying ports 9 through 16, etc.
Within each octet, the most significant bit represents the
lowest numbered port, and the least significant bit
represents the highest numbered port. Thus each port
of the system is represented by a single bit within the
value of this object. If that bit has a value of '1'
then that port is included in the VLAN; the port is not
included if its bit has a value of '0'.rw OCTET STRING .1.3.6.1.4.1.52.1011.3.13.1.4 |
els100SwitchVlanStatusControl variable used to enable or disable the operation
of the associated VLAN in the system.rw Enumeration .1.3.6.1.4.1.52.1011.3.13.1.5 |
els100SwitchVlanPortTableThe VLAN port configuration table. SEQUENCE OF Els100SwitchVlanPortEntry .1.3.6.1.4.1.52.1011.3.14 |
els100SwitchVlanPortEntryAn entry in the VLAN port configuration table. Els100SwitchVlanPortEntry .1.3.6.1.4.1.52.1011.3.14.1 |
els100SwitchVlanPortIdThe number of the port, from 1 to number of ports
in the system.ro INTEGER .1.3.6.1.4.1.52.1011.3.14.1.1 |
els100SwitchVlanPvidThe port's VLAN ID. For tagged VLAN's, this variable
defines a 12 bit port VLAN ID (PVID) used as the
identifier of the VLAN in the packet tag.rw INTEGER .1.3.6.1.4.1.52.1011.3.14.1.2 |
els100SwitchVlanPortTypeFor tagged VLAN's, the VLAN port type, either hybrid or
access. Hybrid ports allow both tagged and untagged
packets to enter the switch. Access ports only accept
untagged packets.rw Enumeration .1.3.6.1.4.1.52.1011.3.14.1.3 |
els100SwitchPriorityEnableGlobally enable or disable the Class of Service traffic
priority mechanism for the system.rw Enumeration .1.3.6.1.4.1.52.1011.3.15 |
els100SwitchPriorityThresholdThe global priority threshold level for the system
at which VLAN tagged frames entering the associated
port are assigned a high priority. This variable can
have a value from (0...7). Traffic with a priority level
equal to or above this value are high priority. Traffic
with a priority level below this value are normal priority.rw INTEGER .1.3.6.1.4.1.52.1011.3.16 |
els100SwitchPriorityPortTableThe priority port table. SEQUENCE OF Els100SwitchPriorityPortEntry .1.3.6.1.4.1.52.1011.3.17 |
els100SwitchPriorityPortEntryAn entry in the port priority table. Els100SwitchPriorityPortEntry .1.3.6.1.4.1.52.1011.3.17.1 |
els100SwitchPriorityPortIdThe port number, from 1 to number of ports in the
system.ro INTEGER .1.3.6.1.4.1.52.1011.3.17.1.1 |
els100SwitchPriorityDefaultThe port priority level assigned to untagged
traffic entering the associated port. This variable
can have a value in the range (0...7). This value is
compared to the value of the els100SwitchPriorityThreshold
variable to determine if the traffic on the port is
high or normal.rw INTEGER .1.3.6.1.4.1.52.1011.3.17.1.2 |
els100SwitchSpanningTreeStandbyGlobally enable or disable Spanning Tree Standby.
If set to disable, every port will instanly enter
forwarding mode after link uprw Enumeration .1.3.6.1.4.1.52.1011.3.18 |