CONV-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
29
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
29 total| Object Name |
|---|
IMPORTSProvides configuration information and attributes of each of the module's
convergence ports.
The table contains two rows of default entries; some of these entries can be
modified. If required, you can add additional entries. SEQUENCE OF CxConvEntry .1.3.6.1.4.1.495.2.1.6.8.1 |
cxFwkCircuitTableProvides the attributes of the WAN service(s) used and the circuits
established by each convergence port. It also identifies statistical
information about the WAN circuits.
The table contains two rows of default entries; some of these entries can be
modified. If required, you can add additional entries. SEQUENCE OF CxFwkCircuitEntry .1.3.6.1.4.1.495.2.1.6.8.2 |
cxFwkCircuitEntry CxFwkCircuitEntry .1.3.6.1.4.1.495.2.1.6.8.2.1 |
cxFwkCircuitPortIdentifies the convergence port by a unique index number. This number acts
as an index for this and the cxConvTable.
Range of Values: 1 to the number of convergence ports
Default Values: none
Note that the system defines two default entries; their respective values
are 1 and 2.ro INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.1 |
cxFwkCircuitStateIdentifies the current state of the circuit between the convergence port and
the destination port.
Options:
opened (1): The circuit is active
closed (2): The circuit is not active
opening (3): The circuit is being activated
openFailed (4): The circuit could not be opened.
idle (256): There is no activity over the circuit.
Default Value: None
Configuration Changed: administrativero Enumeration .1.3.6.1.4.1.495.2.1.6.8.2.1.2 |
cxFwkCircuitRowStatusDetermines the status of the objects in a table row.
Options:
invalid (1): row is flagged, after next reset the values will be disabled and
the row will be deleted from the table.
valid (2): values are enabled
Default Value: valid
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.8.2.1.3 |
cxFwkServiceTypeDetermines the WAN service used. At the present time, frame relay is the
only WAN service available.
Options:
frameRelay (1)
notSpecified (256)
Default Value: frameRelay (1)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.8.2.1.4 |
cxFwkServiceProtocolIdentifies the type of connection the WAN service uses. At the present time,
Permanent Virtual Circuit (PVC) is the only type of connection available.
Options
cls (1)
pvc (2)
svc (3)
char (4)
Default Value: pvc (2)
Configuration Changed: administrativerw Enumeration .1.3.6.1.4.1.495.2.1.6.8.2.1.5 |
cxFwkServiceNameIdentifies the textual name of the WAN service used. The system updates the
name automatically when it selects a WAN service for transmission.
Frame Relay is the only WAN service currently available.
Range of Values: 1 to 16 alphanumeric characters
Default Value: Nonero OCTET STRING .1.3.6.1.4.1.495.2.1.6.8.2.1.6 |
cxFwkDestAddressIdentifies the address used to reach the WAN service provider.
Range of Values: 20 octets, each octet ranging from 00 to FF.
Default Value: Nonero OCTET STRING .1.3.6.1.4.1.495.2.1.6.8.2.1.7 |
cxFwkDestAliasDetermines a unique textual name (assigned by a network administrator)
identifying the destination frame relay circuit.
Range of Values: 0-16 alphanumeric characters. (Note that the first character
must be a letter; spaces are not allowed).
Default Value: none
Note: The system defines two default entries; their respective values are
PRIMARY_DEST and BACKUP_DEST.
Related Parameter:
The name must equal a destination alias defined using the
object frpCircuitAlias in the FrameRelayCicuitCfgTable.
Configuration Changed: administrativerw Alias .1.3.6.1.4.1.495.2.1.6.8.2.1.8 |
cxFwkServiceCircuitMduDetermines the maximum size of the data unit (in octets) that may be
transmitted over the WAN circuit.
Range of Values: 0 to 8192
Default Value: 1600
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.9 |
cxFwkServiceCostDetermines the cost of the WAN service. Cost is typically inverse to the
throughput. The smaller the number, the greater the throughput on the port.
A value of 0 indicates that the cost is not known.
Range of Values: 0 to 1000000
Default Value: 0
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.10 |
cxFwkServiceCardIdIdentifies the number of the chassis slot that contains the WAN service
(FR600). This object is not applicable in the CX900 architecture.
Range of Values: 1-16
Default Value: Nonero INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.11 |
cxFwkServiceSapIdIdentifies the ID of the WAN service's SAP (service access point) that the
convergence port uses to establish the circuit. This object is not used if
there is only one SAP on the WAN service.
Range of Values: 0 to 65535
Default Value: Nonero INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.12 |
cxFwkServiceRouteRefDetermines a routing reference number. This number provides a reference for
WAN service providers that offer multiplexing (it is required in situations
where multiple convergence ports are multiplexed over the same DLCI).
If the WAN provider doesn't provide multiplexing, then the object should be
set to 0.
If the WAN provider does provide multiplexing, a value of 0 instructs the
provider not to multiplex other LAN traffic over the same circuit and the
frame must be sent as received (regular RFC 1490 encapsulation in the case of
frame relay service provider). If the value is set to other than 0 (1-255),
the provider will use this number as a reference in its multiplexing
encapsulation header. Each reference within the same WAN circuit must be
unique.
Range of Values: 0-255
Default Value: None
Configuration Changed: administrativerw INTEGER .1.3.6.1.4.1.495.2.1.6.8.2.1.13 |
cxFwkStatsInternalErrorsIdentifies the number of internal errors recognized by the convergence port.
Range of Values: 1 to 4, 294, 967, 295
Default Value: 0ro Counter .1.3.6.1.4.1.495.2.1.6.8.2.1.15 |
cxFwkStatsRegistrationErrorsIdentifies the number of errors that occurred when the convergence port
attempted to register itself to the framework.
Range of Values: 1 to 4, 294, 967, 295
Default Value: 0ro Counter .1.3.6.1.4.1.495.2.1.6.8.2.1.16 |
cxFwkStatsQueryErrorsIdentifies the number of times the convergence port requested a service that
was not available.
Range of Values: 1 to 4, 294, 967, 295
Default Value: 0ro Counter .1.3.6.1.4.1.495.2.1.6.8.2.1.17 |
cxFwkStatsOpenErrorsIdentifies the number of errors that occurred when the convergence port
attempted to establish a connection with a WAN service. A value here may
indicate congestion at the WAN service, or a configuration problem.
Range of Values: 1 to 4, 294, 967, 295
Default Value: 0ro Counter .1.3.6.1.4.1.495.2.1.6.8.2.1.18 |
cxFwkStatsResetsIdentifies the number of resets received from the WAN service. A large value
here may signify a breakdown on the bus or the WAN circuit.
Range of Values: 1 to 4, 294, 967, 295
Default Value: 0ro Counter .1.3.6.1.4.1.495.2.1.6.8.2.1.19 |
cxConvEntry CxConvEntry .cxConvTable.1 |
cxConvPortIdentifies the number of a specific convergence port. This number acts as an
index to this and the cxFwkCircuitTable.
Range of Values: 1 - 32
Default Value: None
Note:
The system defines two default entries; their respective values
are 1 and 2.ro INTEGER .cxConvTable.1.1 |
cxConvPortAliasDetermines a textual name (alias), assigned by the network administrator,
which identifies a particular convergence port. The alias is used by the
routing and bridging protocols when they bind to this port.
Range of Values: 0-16 alphanumeric characters. (Note that the first
character must be a letter, and spaces are not allowed).
Default Value: none
Note: The system defines two default entries; their respective
values are CNV_PORT1 and CNV_PORT2.
Configuration Changed: administrativerw Alias .cxConvTable.1.2 |
cxConvRowStatusDetermines the status of the objects in a table row.
Options:
valid (1): values are enabled
invalid (2) row is flagged, after next reset values will be disabled and the
row will be deleted from the table).
Default Value: valid
Configuration Changed: administrativerw Enumeration .cxConvTable.1.3 |
cxConvIfIndexIdentifies the table row that contains configuration or monitoring objects
for a specific type of physical interface.
Range of Values: 1 to the number of entries in the interface table.
Default Value: Nonero INTEGER .cxConvTable.1.4 |
cxConvStateDetermines whether the convergence port is active (on). When the object is
set to on, transmission can begin over the port; when the object is set to
off transmission will be stopped.
Options:
on (1)
off (2)
Default Value: on
Configuration Changed: administrativerw Enumeration .cxConvTable.1.5 |
cxConvCompressionDetermines whether the port is linked to a compression port. If the port is
not linked to a compression port the value is 0. If the port is linked to a
compression port, then the object identifies the compression port number
(CompressPortNumber on CompressTable.)
Range of Values: 0 to 64.
Default Value: 0.
Configuration Changed: administrativerw INTEGER .cxConvTable.1.6 |
cxConvCompCompatibilityDetermines the data compression synchronization algorithm.
When the CX1000 interfaces with Memotec models CL2800, CL5050, CL5200,
CL5300, or CL5500, this object must be set to compatibleACC; when it
interfaces with any other product the object must be set to
compatibleMemotec.
The CX900 must always be set to
compatibleMemotec.
Options:
compatibleMemotec (1)
compatibleACC (2)
Default Value: compatibleMemotec (1)
Configuration Changed: administrativerw Enumeration .cxConvTable.1.7 |