CM-SYSTEM-MIB
This module defines the System MIB definitions used by the F3 (FSP150CM/CC) product lines. Copyright (C) ADVA Optical Networking.
Main OID:
cmSystemMIB.1.3.6.1.4.1.2544.1.12.2
180
Objects
Active
Status
11
Dependencies
Imported Objects
Objects
180 total| Object Name |
|---|
cmSystemMIBThis module defines the System MIB definitions used by
the F3 (FSP150CM/CC) product lines.
Copyright (C) ADVA Optical Networking. MODULE-IDENTITY .1.3.6.1.4.1.2544.1.12.2 |
cmSystemObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1 |
cmErrorInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.1 |
lastSetErrorInformationThis provides detailed information on the last SNMP SET
operation failure on the enterprise MIBs.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.1.1 |
cmCliObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.2 |
cliCmdPromptPrefixUser specified command prompt prefix, used by the CLI,
at the system level.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.2.1 |
cmAccessProtocols OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.3 |
telnetEnabledThis provides ability to enable/disable the TELNET protocol on the
system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.1 |
sshEnabledThis provides ability to enable/disable the Secure Shell protocol
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.2 |
ftpEnabledThis provides ability to enable/disable the File Transfer Protocol
(FTP) on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.3 |
scpEnabledThis provides ability to enable/disable the Secure Copy (SCP)
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.4 |
serialPortEnabledThis provides ability to enable/disable the Serial Port
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.5 |
httpEnabledThis provides ability to enable/disable the HTTP protocol
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.6 |
httpsEnabledThis provides ability to enable/disable the HTTP protocol
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.7 |
sftpEnabledThis provides ability to enable/disable the SFTP protocol
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.8 |
tftpEnabledThis provides ability to enable/disable the TFTP protocol
on the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.3.9 |
cmSysSecObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.4 |
securityBannerThis provides ability to manage the security banner text
used for Graphical User Interface as well as CLI access.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.4.1 |
aclTableA list of entries corresponding to the access control
IP network addresses. Agent provides upto 10 access control
IP network addresses to be configured. Access is only
'permitted' from these IP network addresses. SEQUENCE OF ACLEntry .1.3.6.1.4.1.2544.1.12.2.1.4.2 |
aclEntryAn entry containing information applicable to a particular
Access Control IP Network Address that can be configured. ACLEntry .1.3.6.1.4.1.2544.1.12.2.1.4.2.1 |
aclEntryIndexAn arbitrary integer index value used to uniquely identify
an ACL entry within an ACL. The manager may not assume any
particular semantics or meaning to this index, except that
it identifies a logical row in the table.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.1 |
aclEntryFilterActionWhether the network IP address specified by aclEntryNetworkAddress
and aclEntryNetworkMask has permission to access the system.
Currently, only 'permit' is supported.ro CmAclFilterAction .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.2 |
aclEntryNetworkAddressThe network IP address of the entry that will be permitted to access
the system.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.3 |
aclEntryNetworkMaskThe network IP mask of the entry that will be permitted to access
the system.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.4 |
aclEntryEnabledThis enables/disables the entity specified by
aclEntryNetworkAddress and aclEntryNetworkMask to access
the system.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.5 |
aclEntryIpVersionThis object describe the ip version.rw IpVersion (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.6 |
aclEntryNetworkIpv6AddrThis object describe the ipv6 adress.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.7 |
aclEntryPrefixLengthThis object describe the ipv6 Prefix length.rw Integer32 .1.3.6.1.4.1.2544.1.12.2.1.4.2.1.8 |
serialPortDisconnectAutoLogOffThis provides ability to manage the property of the system, which
causes Auto Logoff of the user session on the serial port, when
the serial port is disconnected.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.4.3 |
securityPromptEnabledThis object allows management of the CLI security prompt.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.4.4 |
cmSysModeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.5 |
ntpModeThis provides ability to manage the Network Time Protocol (NTP)
mode on the system. Currently, the system only supports
'client' mode.rw CmNtpMode .1.3.6.1.4.1.2544.1.12.2.1.5.1 |
autoProvModeThis provides ability to manage the Auto Provisioning Mode
on the system. If the auto provisioning mode is 'off', auto
discovery is disabled. Network Elements (shelves) need to be
manually configured from the user interfaces. If the auto
provisioning mode is 'confirm', Network Elements (shelves) are
auto discovered, however, they need to be accepted explicitly from
user interfaces to be managed. If the auto provisioning mode
is 'auto', Network Elements (shelves) are auto discovered and
auto provisioned, as permanent, in the system.rw Enumeration .1.3.6.1.4.1.2544.1.12.2.1.5.2 |
sysTimeOfDayTypeThis object provides ability to configure System Time of Day source.
This can be local, ntp or ptp.
Before setting sysTimeOfDayType the f3PtpSysTimeOfDayClock object must be
set to configure PTP Telecom Slave object to be used as Clock source.rw TimeOfDayType .1.3.6.1.4.1.2544.1.12.2.1.5.3 |
ntpServerConfigTypeThis object describe the ntp server configure type.rw ServerConfigType .1.3.6.1.4.1.2544.1.12.2.1.5.4 |
sysLogServerConfigTypeThis object describe the sys log server configure type.rw ServerConfigType .1.3.6.1.4.1.2544.1.12.2.1.5.5 |
sysUseUtcLeapOffsetEnableThis attribute indicates whether to use the currentUtcLeapOffset
in Announce message from PTP to get UTC time from TAI based
timestamps in case we want DM/TWAMP timestamping based on UTC time.
This attribute only works when PTP/TimeClock is configured as source of system time of day.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.5.6 |
cmDatabaseObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.6 |
databaseActionInitiates a configuration database action. This object is
write only. Supported actions are:
backup(1) - Backup the saved configuration database.
restore(2) - Restore the database to the standby partition.
activate(3) - Switches the standby and active partitions and
restarts the system.
save-sysdefaults(4) - Save the database as system defaults.
new-sysdefaults(5) - Restart the system and overwrite the
old system default database with the
factory default database.
restore-sysdefaults(6) - Restart the system using the system
default database.
restore-factorydefaults(7) - Restart the system using the factory
default database.
propagate-to-standby-nemi(8) - Propagate the running database
to standby NEMI and activate it.
force-normal(9) - Accept the database of the NEMI when the NEMI is in DB_maint status.rw Enumeration .1.3.6.1.4.1.2544.1.12.2.1.6.1 |
databaseLastSaveTimeThis object gives value of the last database save time.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.6.2 |
databaseTableThis table lists information about thns. SEQUENCE OF DatabaseEntry .1.3.6.1.4.1.2544.1.12.2.1.6.3 |
databaseEntryA conceptual row in the databaseTable. DatabaseEntry .1.3.6.1.4.1.2544.1.12.2.1.6.3.1 |
databaseIndexAn arbitrary integer index value used to uniquely identify
an entry within the databaseTable.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.6.3.1.1 |
databaseTypeThe type of database partition.ro CmVersionType .1.3.6.1.4.1.2544.1.12.2.1.6.3.1.2 |
databaseVersionThe database version string.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.6.3.1.3 |
cmSoftwareObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.7 |
softwareActionThis object is write only. Setting this object initiates
the specified action.
Supported actions are:
install(1) - Install software.
schedule-upgrade(2) - Schedule a software upgrade. At the
scheduled time, the system will reboot and
load the software image stored on the
standby partition. The scheduled time
can be specified by softwareUpgradeTime.
Also see softwareValidationTimer.
cancel-upgrade(3) - Cancel a scheduled software upgrade.
validate-upgrade(4) - Indicate software as valid and cancel the
validation timer.
revert-upgrade(5) - Revert to previous software image if it
still exists.
propagate-to-standby-nemi(6) - Propagate the running software release
to standby NEMI and active it.rw Enumeration .1.3.6.1.4.1.2544.1.12.2.1.7.1 |
softwareUpgradeTimeSpecifies the date and time to perform a software upgrade reboot.
If this object is set to a date and time in the past or has never
been set, the upgrade reboot will happen as soon as softwareAction
is set to schedule-upgrade(2). This value becomes read-only when
an upgrade has been scheduled. Default value is 1-1-2000 00:00:00.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.7.2 |
softwareValidationTimerTime in minutes before the system will reboot and revert to the active
software after a software upgrade. If set to 0, the timer is
disabled and the software will automatically be validated after
a software upgrade reboot. This object becomes read-only when
the software validation timer is active. Default value is 0.
When enabled, valid values of the timer range from 10 minutes to 720 minutes.rw INTEGER (0 | 10..720) .1.3.6.1.4.1.2544.1.12.2.1.7.3 |
softwareTableThis table lists information about the software installed
in the active and standby partitions. SEQUENCE OF SoftwareEntry .1.3.6.1.4.1.2544.1.12.2.1.7.4 |
softwareEntryA conceptual row in the softwareTable. SoftwareEntry .1.3.6.1.4.1.2544.1.12.2.1.7.4.1 |
softwareIndexAn arbitrary integer index value used to uniquely identify
an entry within the softwareTable.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.7.4.1.1 |
softwareTypeThe type of software partition.ro CmVersionType .1.3.6.1.4.1.2544.1.12.2.1.7.4.1.2 |
softwareVersionThe software version string.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.7.4.1.3 |
cmFileServicesObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.8 |
fileServicesActionThis object is write only. Setting this object initiates
a file transfer
Supported actions are:
get-database(1) - Copy a backup database from a
remote server and place it in the staging
area. (See databaseAction)
put-database(2) - Copy a backup database to a remote
server. (See databaseAction)
software-copy(3) - Transfer a software image file to the
system and write it to the standby
partition.
get-sys-database(4) - Copy a system database from a
remote server and place it in the staging
area. (See databaseAction)
put-sys-database(5) - Copy a system database to a remote
server. (See databaseAction)
get-defaultsvalue-file(6) - Transfer the Defaults Value file
to the system.
put-sysresetdebuginfo-file(7) - Transfer the System Reset Debug Information
file to a remote server.
put-securitylog-file(8) - Transfer the System Security Log Information
file to a remote server.
put-alarmlog-file(9) - Transfer the System Alarm Log Information
file to a remote server.
put-audit-file(10) - Transfer the System Audit Log Information
file to a remote server.
get-config-file(11) - Transfer the Configuration File from a remote server.
put-config-file(12) - Transfer the Configuration File to a remote server.
put-sat-result(13) - Transfer the SAT test result file to a remote server.rw Enumeration .1.3.6.1.4.1.2544.1.12.2.1.8.1 |
fileServicesMethodSpecifies the method of transferring the file. Note
that web(4) is a read-only enumeration.rw CmFileTransferMethod .1.3.6.1.4.1.2544.1.12.2.1.8.2 |
fileServicesServerIpIP address of the remote server. The value of this
object is cleared when fileServicesAction is set.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.8.3 |
fileServicesUserIdUser ID to use to authenticate the file transfer. The value
of this object is cleared when fileServicesAction is set.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.8.4 |
fileServicesPasswordUser password to authenticate the file transfer.
Reading this object will return an empty string if the
password has not been set or ***** if the password has
been set. The value of this object is cleared when
fileServicesAction is set.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.8.5 |
fileServicesRemoteFilePath and name of the remote file. The value of this object
is cleared when fileServicesAction is set.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.8.6 |
fileServicesStatusStatus of the user initiated file transfer.ro CmFileServicesStatus .1.3.6.1.4.1.2544.1.12.2.1.8.7 |
fileServicesPercentCompletePercent completion of operation.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.8.8 |
fileServicesModeThis object provides information on the current state
of file services.ro CmFileServicesMode .1.3.6.1.4.1.2544.1.12.2.1.8.9 |
fileServicesServerTypeThis object describe the remote server's address type.rw FileTransferServerType .1.3.6.1.4.1.2544.1.12.2.1.8.10 |
fileServicesServerIpv6AddrIPv6 address of the remote server. The value of this
object is cleared when fileServicesAction is set.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2544.1.12.2.1.8.11 |
cmLogObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.9 |
cmSysLogObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.9.1 |
sysLogServerTableThis table allows configuration of the remote syslog hosts. SEQUENCE OF SysLogServerEntry .1.3.6.1.4.1.2544.1.12.2.1.9.1.1 |
sysLogServerEntryA conceptual row in the sysLogServerTable. SysLogServerEntry .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1 |
sysLogServerIndexAn integer index value used to uniquely identify
an entry within the sysLogServerTable.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.1 |
sysLogIpAddressIP address of the remote syslog server. Value of 0.0.0.0 indicates
the sys log server is not configured.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.2 |
sysLogPortOptional port address of the remote log server. If not specified,
the default port for the standard syslog utility (UDP Port 514)
will be used.rw Integer32 .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.3 |
sysLogIpVersionThis object describe the ip version.rw IpVersion (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.4 |
sysLogIpv6AddrThis object describe the ipv6 address.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.1.1.1.5 |
cmSecLogObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.9.2 |
secLog2sysLogEnabledThis allows to enable/disable the system security log to syslog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.2.1 |
cmAuditLogObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.9.3 |
auditLog2sysLogEnabledThis allows to enable/disable the system audit log to syslog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.3.1 |
auditLog2fileEnabledThis allows to enable/disable the system audit log to file.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.3.2 |
cmAlarmLogObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.9.4 |
alarmLog2sysLogEnabledThis allows to enable/disable the system alarm log to syslog.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.4.1 |
alarmLog2fileEnabledThis allows to enable/disable the system alarm log to file.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.9.4.2 |
cmTimeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.10 |
ntpClientEnabledThis allows to enable/disable the NTP client.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.10.1 |
ntpPrimaryServerIP address of the primary remote NTP time server. Value of 0.0.0.0
indicates the NTP server is not configured.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.10.2 |
ntpBackupServerIP address of the backup remote NTP time server. Value of 0.0.0.0
indicates the NTP server is not configured.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.10.3 |
ntpTypeType of communication with the remote NTP server.ro CmNtpType .1.3.6.1.4.1.2544.1.12.2.1.10.4 |
ntpActiveServerIndication of which server is currently active.ro CmNtpServerType .1.3.6.1.4.1.2544.1.12.2.1.10.5 |
ntpSwitchServerOperation to switch the NTP Server.rw CmNtpServerType .1.3.6.1.4.1.2544.1.12.2.1.10.6 |
ntpServerRoundTripDelayThis object provides the round-trip delay (in microseconds)
to the NTP Server.
It returns a value of 0 if NTP is not enabled.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.10.7 |
ntpServerPrecisionThis object provides the precision (in microseconds)
to the NTP Server.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.10.8 |
ntpPollingIntervalThis object allows ability to configure the NTP polling
interval in seconds. Polling interval is the time
between successive NTP client requests to update local
time based on time at the NTP server.rw Integer32 .1.3.6.1.4.1.2544.1.12.2.1.10.9 |
ntpPrimaryServerIpVersionThis object describe the ipversion of ntp server.rw IpVersion (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.2.1.10.10 |
ntpPrimaryServerIpv6AddrThis object describe the ipv6 adress of ntp primary server.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2544.1.12.2.1.10.11 |
ntpBackupServerIpVersionThis object describe the ipversion of ntp server.rw IpVersion (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.2.1.10.12 |
ntpBackupServerIpv6AddrThis object describe the ipv6 adress of ntp backup server.rw Ipv6Address (IPV6-TC) .1.3.6.1.4.1.2544.1.12.2.1.10.13 |
cmSnmpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.11 |
f3SnmpTargetAddrExtTableThis table is an extension of the standard snmpTargetAddrTable(SNMP-TARGET-MIB).
This table is used to manage the SNMP Dying Gasp support. SEQUENCE OF F3SnmpTargetAddrExtEntry .1.3.6.1.4.1.2544.1.12.2.1.11.1 |
f3SnmpTargetAddrExtEntryA conceptual row in the f3SnmpTargetAddrExtTable. F3SnmpTargetAddrExtEntry .1.3.6.1.4.1.2544.1.12.2.1.11.1.1 |
f3SnmpTargetAddrExtDyingGaspPortWhen SNMP Dying Gasp is enabled at Card level,
this attribute provides information on the interface (physical port)
through which this Target Address is reachable
(using Layer 3 ping, trace route).ro VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.11.1.1.1 |
f3SnmpTargetAddrExtDyingGaspEnabledWhen SNMP Dying Gasp is enabled at Card level,
this attribute specifies whether this Target Address entry should be
used in the SNMP Dying Gasp TRAP PDU or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.11.1.1.2 |
f3SnmpTargetAddrExtDyingGaspActiveWhen SNMP Dying Gasp is enabled at Card level, in case of
multiple target addresses resolving to the same interface (port),
this flag indicates which target address is used for the SNMP TRAP PDU.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.11.1.1.3 |
f3SnmpTargetAddrExtBulkTrapsEnabledProvides ability to enable/disable the Snmp Bulk Traps on
the Target Address.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.11.1.1.4 |
f3SnmpEngineIDAn SNMP engine's administratively-unique identifier.
Please note that f3SnmpEngineID differs from the
standard snmpEngineID (SNMP-FRAMEWORK-MIB) with
MAX-ACCESS as read-write.rw SnmpEngineID (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.12.2.1.11.2 |
f3SnmpLongIfAliasThis provides ability to enable/disable longer version of ifAlias. If enabled, ifAlias variable can support
up to 255 character string and when disabled ifAlias is limited to 64 character string. When disabled and if
alias is longer than 64 characters the ifAlias will return a string that is truncated to 64 characters.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.11.3 |
cmResetCauseObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.12 |
f3SysLastResetTypeThis provides the System Last Reset Type.ro RestartType (CM-COMMON-MIB) .1.3.6.1.4.1.2544.1.12.2.1.12.1 |
f3SysLastResetCauseTypeThis provides the System Last Reset Cause Type.ro CmRestartCauseType .1.3.6.1.4.1.2544.1.12.2.1.12.2 |
f3SysLastAbnormalResetTimestamp1This provides the timestamp of the most recent abnormal reset.
Note that the system keeps debug logs with 3 most recent
abnormal resets. 8 octets of 0 value indicates that
there was no abnormal reset of the system.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.12.3 |
f3SysLastAbnormalResetTimestamp2This provides the timestamp of the second most recent abnormal reset.
Note that the system keeps debug logs with 3 most recent
abnormal resets. 8 octets of 0 value indicates that
there was only one (f3SysLastAbnormalResetTimestamp1) abnormal
reset of the system.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.12.4 |
f3SysLastAbnormalResetTimestamp3This provides the timestamp of the third most recent abnormal reset.
Note that the system keeps debug logs with 3 most recent
abnormal resets. 8 octets of 0 value indicates that
there were only two (f3SysLastAbnormalResetTimestamp1,
f3SysLastAbnormalResetTimestamp2) abnormal resets of the system.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.12.5 |
f3NotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.13 |
f3DatabaseSyncTrapObjectThis object provides the Object Identifier (OID) of the entity
that needs to be synchronized. This object is not accessible,
it is only carried in the f3DatabaseSyncTrap notification. VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.13.1 |
f3ConfigFileObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.14 |
f3ConfigFileActionFileNameConfiguration File name on which configFileAction is initiated.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.14.1 |
f3ConfigFileActionConfiguration File action to invoke config file operations.rw F3ConfigFileAction .1.3.6.1.4.1.2544.1.12.2.1.14.2 |
f3ConfigFileStatusThis object provides status of Configuration File actions.ro F3ConfigFileStatus .1.3.6.1.4.1.2544.1.12.2.1.14.3 |
f3ConfigFileErrorInformationThis object provides additional information for failed
Configuration File actions.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.14.4 |
f3ConfigFileTableThis table lists information about the configuration files that
are resident on the node. SEQUENCE OF F3ConfigFileEntry .1.3.6.1.4.1.2544.1.12.2.1.14.5 |
f3ConfigFileEntryA conceptual row in the f3ConfigFileTable. F3ConfigFileEntry .1.3.6.1.4.1.2544.1.12.2.1.14.5.1 |
f3ConfigFileIndexAn arbitrary integer index value used to uniquely identify
an entry within the f3ConfigFileTable. Integer32 .1.3.6.1.4.1.2544.1.12.2.1.14.5.1.1 |
f3ConfigFileNameName of the configuration file.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.14.5.1.2 |
f3ConfigFileDescriptionUser description of the configuration file.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.14.5.1.3 |
f3ConfigFilePercentCompleteThis object provides configure file percent complete.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.14.6 |
cmFeatureManagementObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.15 |
f3SystemFeatureTableThis table allows ability to manage enabling/disabling system features. SEQUENCE OF F3SystemFeatureEntry .1.3.6.1.4.1.2544.1.12.2.1.15.1 |
f3SystemFeatureEntryA conceptual row in the f3SystemFeatureTable. F3SystemFeatureEntry .1.3.6.1.4.1.2544.1.12.2.1.15.1.1 |
f3SystemFeatureIndexAn arbitrary integer index value used to uniquely identify
an entry within the f3SystemFeatureTable.ro Integer32 .1.3.6.1.4.1.2544.1.12.2.1.15.1.1.1 |
f3SystemFeatureNameThis object provides the name of the system feature.ro DisplayString .1.3.6.1.4.1.2544.1.12.2.1.15.1.1.2 |
f3SystemFeatureEnabledThis object allows system feature control. If a specific feature
is disabled, the relevant operations to use that feature are denied.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.15.1.1.3 |
cmLldpV2DestAdressADVAExtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.16 |
f3SystemLldpV2DestAddressADVAExtTableThis extension table adds a row status to allow user add/delete/edit the LLDP
Destination Address which is defined to Read-Only in the standard MIB. SEQUENCE OF F3SystemLldpV2DestAddressADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.1 |
f3SystemLldpV2DestAddressADVAExtEntryA conceptual row in the f3SystemLldpV2DestAddressADVAExtTable. F3SystemLldpV2DestAddressADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.1.1 |
f3SystemLldpV2DestAddressADVAExtIndexAn arbitrary integer index value used to uniquely identify
an entry within the f3SystemLldpV2DestAddressADVAExtTable. Integer32 .1.3.6.1.4.1.2544.1.12.2.1.16.1.1.1 |
f3SystemLldpV2ADVAExtDestMacAddressThis attribute description the standard MIB about LLDP Destination Mac Address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.1.1.2 |
f3SystemLldpV2DestAddressADVAExtRowStatusThe status of this row.
The f3SystemLldpV2DestAddressADVAExtRowStatus object may be modified if
the associated instance of this object is equal to active(1),
notInService(2), or notReady(3).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.1.1.3 |
f3SystemLldpV2PortConfigADVAExtTableThis extension table adds a row status to allow user add/delete/edit the LLDP
Destination Address for one port. SEQUENCE OF F3SystemLldpV2PortConfigADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.2 |
f3SystemLldpV2PortConfigADVAExtEntryA conceptual row in the f3SystemLldpV2PortConfigADVAExtTable. F3SystemLldpV2PortConfigADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.2.1 |
f3SystemLldpV2PortConfigADVAExtIfIndexThe interface index value used to identify the port
associated with this entry. Its value is an index into
the interfaces MIB.
The value of this object is used as an index to the
f3SystemLldpV2PortConfigADVAExtTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.1 |
f3SystemLldpV2PortConfigADVAExtDestAddressIndexThe index value used to identify the destination
MAC address associated with this entry. Its value identifies
the row in the lldpV2DestAddressTable where the MAC address
can be found.
The value of this object is used as an index to the
f3SystemLldpV2PortConfigADVAExtTable. LldpV2DestAddressTableIndex (LLDP-V2-TC-MIB) .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.2 |
f3SystemLldpV2PortConfigADVAExtAdminStatusThe administratively desired status of the local LLDP agent.
If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is
set to a value of 'txOnly(1)', then LLDP agent transmits
LLDPframes on this port and it does not store any
information about the remote systems connected.
If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is
set to a value of 'rxOnly(2)', then the LLDP agent
receives, but it does not transmit LLDP frames on this port.
If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set
to a value of 'txAndRx(3)', then the LLDP agent transmits
and receives LLDP frames on this port.
If the associated f3SystemLldpV2PortConfigADVAExtAdminStatus object is set
to a value of 'disabled(4)', then LLDP agent does not
transmit or receive LLDP frames on this port. If there is
remote systems information which is received on this port
and stored in other tables, before the port's
f3SystemLldpV2PortConfigADVAExtAdminStatus becomes disabled, then that
information is deleted.rw Enumeration .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.3 |
f3SystemLldpV2PortConfigADVAExtNotificationEnableThe f3SystemLldpV2PortConfigADVAExtNotificationEnable controls, on a per
agent basis, whether or not notifications from the agent
are enabled. The value true(1) means that notifications are
enabled; the value false(2) means that they are not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.4 |
f3SystemLldpV2PortConfigADVAExtTLVsTxEnableThe f3SystemLldpV2PortConfigADVAExtTLVsTxEnable, defined as a bitmap,
includes the basic set of LLDP TLVs whose transmission is
allowed on the local LLDP agent by the network management.
Each bit in the bitmap corresponds to a TLV type associated
with a specific optional TLV.
It should be noted that the organizationally-specific TLVs
are excluded from the f3SystemLldpV2PortConfigADVAExtTLVsTxEnable bitmap.
LLDP Organization Specific Information Extension MIBs should
have similar configuration object to control transmission
of their organizationally defined TLVs.
The bit 'portDesc(0)' indicates that LLDP agent should
transmit 'Port Description TLV'.
The bit 'sysName(1)' indicates that LLDP agent should transmit
'System Name TLV'.
The bit 'sysDesc(2)' indicates that LLDP agent should transmit
'System Description TLV'.
The bit 'sysCap(3)' indicates that LLDP agent should transmit
'System Capabilities TLV'.
There is no bit reserved for the management address TLV type
since transmission of management address TLVs are controlled
by another object, lldpV2ConfigManAddrTable.
The default value for f3SystemLldpV2PortConfigADVAExtTLVsTxEnable object is
empty set, which means no enumerated values are set.
The value of this object is restored from non-volatile
storage after a re-initialization of the management system.rw Bits .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.5 |
f3SystemLldpV2PortConfigADVAExtStorageTypeThe storage type for this conceptual row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.6 |
f3SystemLldpV2PortConfigADVAExtRowStatusThe status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of f3SystemLldpV2PortConfigADVAExtRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
f3SystemLldpV2PortConfigADVAExtRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The f3SystemLldpV2PortConfigADVAExtRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.2.1.7 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtTableThis extension table adds a row status to allow user add/delete/edit the LLDP
Destination Address for one port. SEQUENCE OF F3SystemLldpV2ManAddrConfigTxPortsADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.3 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtEntryA conceptual row in the f3SystemLldpV2ManAddrConfigTxPortsADVAExtTable. F3SystemLldpV2ManAddrConfigTxPortsADVAExtEntry .1.3.6.1.4.1.2544.1.12.2.1.16.3.1 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtRefInterfaceThis object describe the Tx Port is on what interface,
its value should be management tunnel or one dcn or none. VariablePointer (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.3.1.1 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtEnableThis object describe the interface on Tx Ports whether enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.3.1.2 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtStorageTypeThe storage type for this conceptual row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.3.1.3 |
f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatusThe status of this row. An entry MUST NOT exist in the
active state unless all objects in the entry have an
appropriate value, as described
in the description clause for each writable object.
The values of f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus supported are
createAndGo(4) and destroy(6). All mandatory attributes
must be specified in a single SNMP SET request with
f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus value as createAndGo(4).
Upon successful row creation, this object has a
value of active(1).
The f3SystemLldpV2ManAddrConfigTxPortsADVAExtRowStatus object may be modified if
the associated instance of this object is equal to active(1).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.12.2.1.16.3.1.4 |
f3LldpV2ConfigurationADVAExtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.17 |
f3LldpMaxNeighborsActionDiscard: information selected to be discarded is the
information in the current LLDPDU.
Delete entry::information selected to be discarded is
currently in the LLDP remote systems MIB.rw LldpV2ConfigurationADVAExtMaxNeighborsAction .1.3.6.1.4.1.2544.1.12.2.1.17.1 |
snmpIPv6UDPDomain OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.18 |
f3RawDataObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.19 |
f3RawDataServerFtProtocolSpecifies the method of transferring the file. Note
that web(4) is a read-only enumeration.rw CmFileTransferMethod .1.3.6.1.4.1.2544.1.12.2.1.19.1 |
f3RawDataServerFtServerNameIP address of the raw data server. Value of 0.0.0.0
indicates the raw data server is not configured.rw IpAddress .1.3.6.1.4.1.2544.1.12.2.1.19.2 |
f3RawDataServerFtUserIdUser ID to use to authenticate the file transfer.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.19.3 |
f3RawDataServerFtPasswdUser password to authenticate the file transfer.
Reading this object will return an empty string if the
password has not been set or ***** if the password has
been set.rw DisplayString .1.3.6.1.4.1.2544.1.12.2.1.19.4 |
f3LldpV2RemoteSystemsData OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.1.20 |
f3LldpV2RemExtTableThis table is an extension of the standard lldpV2RemTable (LLDP-V2-MIB).
This table adds remote TTL attribute support SEQUENCE OF F3LldpV2RemExtEntry .1.3.6.1.4.1.2544.1.12.2.1.20.1 |
f3LldpV2RemExtEntryA conceptual row in the f3LldpV2RemExtTable. F3LldpV2RemExtEntry .1.3.6.1.4.1.2544.1.12.2.1.20.1.1 |
f3LldpV2RemTTLInteger value which indicates the number of seconds that the
recipient LLDP agent is to regard the information associated
with particular MSAP identifier to be validro Unsigned32 .1.3.6.1.4.1.2544.1.12.2.1.20.1.1.1 |
cmSystemNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.2 |
cmStateChangeTrapThis is the State Change Notification per Interface sent by the agent.
The actual attribute value is sent by the agent in the form of
a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.1 |
cmAttributeValueChangeTrapThis is the Attribute Value Change Notification sent by the agent.
The actual attribute value is sent by the agent in the form of
a varbind list, as additional objects, as per SMIv2 (RFC2578, Section 8.1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.2 |
cmObjectCreationTrapThis is the Object Creation Notification sent by the agent.
The index value of the SNMP Row that is created is sent by the
agent in the form of a varbind list, as additional objects,
as per SMIv2 (RFC2578, Section 8.1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.3 |
cmObjectDeletionTrapThis is the Object Deletion Notification sent by the agent.
The index value of the SNMP Row that is deleted is sent by the
agent in the form of a varbind list,
as per SMIv2 (RFC2578, Section 8.1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.4 |
cmSnmpDyingGaspTrapThis is the Dying Gasp SNMP trap sent by the agent. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.5 |
f3DatabaseSyncTrapThis is the Database Synchronization trap sent by
the agent for bulk operations. The var bind list
can contain multiple variables with OIDs as
f3DatabaseSyncTrapObject and values as the OIDs
of the entities that need synchronization.
The var-binds are sent implicitly, as per
SMIv2 (RFC2578, Section 8.1). NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.2.6 |
cmSystemConformance OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.3 |
cmSystemCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.3.1 |
cmSystemGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.3.2 |
f3SystemBulkGroups OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.3.3 |
f3BulkNotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.4 |
f3StartNeEventLogIndexThis object provides the associated neEventsLogged counter
for the logged first event (trap) in the bulk trap.ro TrapCounter (ADVA-MIB) .1.3.6.1.4.1.2544.1.12.2.4.1 |
f3EndNeEventLogIndexThis object provides the associated neEventsLogged counter
for the logged last event (trap) in the bulk trap.ro TrapCounter (ADVA-MIB) .1.3.6.1.4.1.2544.1.12.2.4.2 |
f3SystemBulkNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.12.2.5 |
f3BulkTrapThis is the bulk trap sent by
the agent for bulk operations. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.12.2.5.1 |