ADVA-FSP3000ALM-MIB
AI MIB Summary
The ADVA-FSP3000ALM-MIB module enables SNMP-based monitoring of alarm states and fault conditions within ADVA FSP 3000 optical transport network equipment. It specifically tracks fiber optical link integrity, signal degradation events, and hardware component failures to facilitate rapid network fault isolation.
Fiber monitoring system for fiber optical networks.
Main OID:
fsp3000alm.1.3.6.1.4.1.2544.1.14
778
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
778 total| Object Name |
|---|
advaMIB OBJECT IDENTIFIER .1.3.6.1.4.1.2544 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1 |
fsp3000almFiber monitoring system for fiber optical networks. MODULE-IDENTITY .1.3.6.1.4.1.2544.1.14 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.0 |
alarmTempCPUThis trap is sent if tempCPU value crossed tresholdMaxTempCPU threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.1 |
alarmTempBoard1This trap is sent if tempBoard1 (CPU board) value crossed tresholdMaxTempBoard1 threshold. Not used on 16ALM-1650D. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.2 |
alarmTempBoard2LowThis trap is sent if tempBoard2 (laser board) value crossed tresholdMinTempBoard2 threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.3 |
alarmTempBoard2HighThis trap is sent if tempBoard2 (laser board) value crossed tresholdMaxTempBoard2 threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.4 |
alarmTempLaserLowThis trap is sent if tempLaser value crossed tresholdMinTempLaser threshold. Not used on 16ALM-1650D. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.5 |
alarmTempLaserHighThis trap is sent if tempLaser value crossed tresholdMaxTempLaser threshold. Not used on 16ALM-1650D. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.6 |
alarmMonNotRunningThis trap is related with enabling/disabling monitoring function by user. The relevant alarm in alarmTable refering to this trap will be set/cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.7 |
alarmFpRunningThis trap is related with initiating/finishing fingerprint calculation. The relevant alarm in alarmTable refering to this trap will be set/cleared. Not used on 16ALM-1650D. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.8 |
alarmFaRunningThis trap is related with initiating/finishing fault analysis. The relevant alarm in alarmTable refering to this trap will be set/cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.9 |
alarmFpMissingThis trap is related with situation when fingerprint was not calculated for a port. The relevant alarm in alarmTable refering to this trap will be set/cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.10 |
alarmThresCrossedFastThis trap is sent if the absolute value of measurementLossDevFast exceeded portThresDeviationFast threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.11 |
alarmThresCrossedMediumThis trap is sent if the absolute value of measurementLossDevMedium exceeded portThresDeviationMedium threshold. This alarm is not supported any longer and thus it will never be raised. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.12 |
alarmThresCrossedSlowThis trap is sent if the absolute value of measurementLossDevSlow exceeded portThresDeviationSlow threshold. This alarm is not supported any longer and thus it will never be raised. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.13 |
alarmLinkBudgetExceededThis trap is sent if measurementLossLinkLoss value exceeded portThresBudget threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.14 |
alarmLinkBudgetNearlyExceededThis trap is sent if measurementLossLinkLoss value exceeded portThresCloseToBudget threshold. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.15 |
alarmManagementStateThis trap is sent each time when portAdminState is changed from/to mgt(4) value. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.16 |
alarmDisabledStateThis trap is sent each time when portAdminState is changed from/to dsbld(6) value. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.17 |
stateChangedTrapThis trap is sent when an entity state is changed (OperState or AdminState). Additionally this trap will contain changed object: portOperState or portAdminState NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.18 |
objectChangedTrapThis trap is sent when an object such as alarm severity or threshold is changed Additionally this trap will contain changed object, portAidString, aidString, if relevant NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.19 |
trapsinkCreatedTrapThis trap is sent every time an new entry is added to the trapsinkTable or ipv6TrapsinkTable or dnsTrapsinkTable NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.20 |
trapsinkDeletedTrapThis trap is sent every time an new entry is removed from the trapsinkTable or ipv6TrapsinkTable or dnsTrapsinkTable NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.21 |
transient15MinMeasCollectedThis trap is every time when all the measurement data for all the port are collected for selected period NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.22 |
transient1DayMeasCollectedThis trap is every time when all the measurement data for all the port are collected for selected period NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.23 |
transientFpStartedThis trap is sent when fingerprint monitoring has started NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.24 |
transientFpCompletedThis trap is sent when fingerprint monitoring has completed with success NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.25 |
transientFpFailedThis trap is sent when fingerprint monitoring has ended with failure NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.26 |
transientSwMgmtActionStartedThis trap is sent when any action related with Software Management is initiated. In case of file-transfer related operations it will contain softwareMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.27 |
transientSwMgmtActionCompletedThis trap is sent when any action related with Software Management is successfully completed. In case of file-transfer related operations it will contain softwareMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.28 |
transientSwMgmtActionFailedThis trap is sent when any action related with Software Management failed. In case of file-transfer related operations it will contain softwareMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.29 |
transientDbMgmtActionStartedThis trap is sent when any action related with Database Management is initiated. In case of file-transfer related operations it will contain additionally databaseMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.30 |
transientDbMgmtActionCompletedThis trap is sent when any action related with Database Management is successfully completed. In case of file-transfer related operations it will contain additionally databaseMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.31 |
transientDbMgmtActionFailedThis trap is sent when any action related with Database Management failed. In case of file-transfer related operations it will contain additionally databaseMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.32 |
alarmNtpServerUnreachableTrap to be sent when NTP servers are unreachable. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.33 |
transientFpSavedThis trap is sent when a completed fingerprint measurement is saved as current fingerprint. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.34 |
transientMonStartedThis trap is sent when monitoring of the particular port was enabled. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.35 |
transientMonStoppedThis trap is sent when monitoring of the particular port was disabled. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.36 |
transientOtdrMeasurementStartedThis trap is sent when manual OTDR measurement was intitiated. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.37 |
transientOtdrMeasurementCompletedThis trap is sent when manual OTDR measurement is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.38 |
transientOtdrMeasurementFailedThis trap is sent when manual OTDR measurement failed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.39 |
transientOtdrMeasurementSavedThis trap is sent when data of manual OTDR measurement was saved. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.40 |
transientFaStartedThis trap is sent when fault analysis in initiated. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.41 |
transientFaCompletedThis trap is sent when fault analysis is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.42 |
transientFaFailedThis trap is sent when fault analysis is completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.43 |
transientFaSavedThis trap is sent when the data of a completed fault analysis was saved. Which FaultPos objects are present is determined by the type AutoFa or (manual)Fa , CorrectedFaultPos is only contained when it exists. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.44 |
transientInternalErrorThis trap is sent when some critical error happened which affects monitoring capabilities NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.45 |
alarmRebootRunningThis trap is to inform user that rebooting of system started NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.46 |
alarmWarmupRunningThis trap is sent when to inform a user about starting/finishing warming up process. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.47 |
alarmBadSysStatThis trap is sent when some critical error happened due to hardware failure. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.48 |
alarmWrongFWVersionThis trap is sent when alarm informing about the fact that firmware version is not up to date is raised/cleared. Not used on 16ALM-1650D. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.49 |
alarmMonProcNotRunningThis trap is sent when some critical error happened which affects monitoring capabilities of the unit. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.50 |
transientFaDeletedThis trap is sent when fault analysis was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.51 |
transientOtdrMeasurementDeletedThis trap is sent when manual OTDR measurement was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.52 |
transientOtdrTraceMgmtActionStartedThis trap is sent when any action related with OTDR Trace Management is initiated. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.53 |
transientOtdrTraceMgmtActionCompletedThis trap is sent when any action related with OTDR Trace Management is successfully completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.54 |
transientOtdrTraceMgmtActionFailedThis trap is sent when any action related with OTDR Trace Management failed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.55 |
alarmAlmPackageMismatchThis trap is sent when softwareVersion and expectedSoftwareVersion values do not match and expectedSoftwareVersion value is not empty and operationMode is set to 'standalone'. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.56 |
alarmEmailNotifyThresCrossedFastThis trap is sent if the absolute value of measurementLossDevFast exceeded portThresDeviationFast threshold and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.57 |
alarmEmailNotifyThresCrossedMediumThis trap is sent if the absolute value of measurementLossDevMedium exceeded portThresDeviationMedium threshold and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. This alarm is not supported any longer and thus it will never be raised. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.58 |
alarmEmailNotifyThresCrossedSlowThis trap is sent if the absolute value of measurementLossDevSlow exceeded portThresDeviationSlow threshold and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. This alarm is not supported any longer and thus it will never be raised. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.59 |
alarmEmailNotifyLinkBudgetExceededThis trap is sent if measurementLossLinkLoss value exceeded portThresBudget threshold and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.60 |
alarmEmailNotifyLinkBudgetNearlyExceededThis trap is sent if measurementLossLinkLoss value exceeded portThresCloseToBudget threshold and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.61 |
authenticationNotificationThis trap is sent when authentication event happens. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.62 |
authenticationNotificationSummaryThis trap is sent when authentication event happens more often than 5 times within 10 seconds. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.63 |
monitorPointCreatedThis trap is sent when Monitor Point was created NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.64 |
monitorPointDeletedThis trap is sent when Monitor Point was deleted NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.65 |
alarmLossDeviationHighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portMonitorThresDeviation. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.66 |
alarmLossHighThis trap is sent if monitorPointLossCurrentLoss value exceeded portMonitorThresLossBudget. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.67 |
alarmRootLinkFaultPON: This trap is sent if alarmLossHigh or alarmLossDeviationHigh is present for all Monitor Points. PES: This trap is sent if the Last Reflection changes. ADL: This trap is sent if a FaultPosition is before at least one corresponding addDropPoint. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.68 |
transientResetMeansStartedThis trap is sent when reset mean value action has started NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.69 |
transientResetMeansCompletedThis trap is sent when reset mean value action has completed with success NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.70 |
transientResetMeansFailedThis trap is sent when reset mean value action has ended with failure NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.71 |
alarmTrafficOutageThis trap is sent when DWDM traffic on the specific port was not detected any longer NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.72 |
userAddedThis trap is sent when user was added NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.73 |
userDeletedThis trap is sent when user was deleted NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.74 |
customizedFpEventCreatedThis trap is sent when a customized Fingerprint Event was created NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.75 |
customizedFpEventDeletedThis trap is sent when a customized Fingerprint Event was deleted NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.76 |
transientExportMgmtActionStartedThis trap is sent when any action related with Export Management is initiated. In case of file-transfer related operations it will contain additionally exportMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.77 |
transientExportMgmtActionCompletedThis trap is sent when any action related with Export Management is successfully completed. In case of file-transfer related operations it will contain additionally exportMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.78 |
transientExportMgmtActionFailedThis trap is sent when any action related with Export Management failed. In case of file-transfer related operations it will contain additionally exportMgmtFileName varbind. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.79 |
alarmSensor1HighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portSensor1Thres. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.80 |
alarmSensor2HighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portSensor2Thres. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.81 |
alarmEmailNotifyRootLinkFaultThis trap is sent if alarmRootLinkFault is set and the corresponding automatic fault analysis measurement has been completed. alarmEmailNotifyCorrectedFaultPos is only contained when it exists. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.82 |
transientTimeChangeThis trap is sent if a time step occured (manually or ntp) NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.83 |
alarmTopologyChangedThis trap is sent if the Link Topology has changed NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.84 |
alarmEmailNotifyLossDeviationHighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portMonitorThresDeviation and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.85 |
alarmEmailNotifyLossHighThis trap is sent if monitorPointLossCurrentLoss value exceeded portMonitorThresLossBudget and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.86 |
alarmEmailNotifySensor1HighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portSensor1Thres and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.87 |
alarmEmailNotifySensor2HighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portSensor2Thres and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.88 |
alarmEmulationModeThis trap is sent when the unit is switched to emulationmode. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.89 |
transientFiberIdentifierStartedThis trap is sent when Fiber Identification has started. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.90 |
transientFiberIdentifierCompletedThis trap is sent when Fiber Identification has completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.91 |
transientFiberIdentifierFailedThis trap is sent when Fiber Identification has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.92 |
transientPkiCertRequestStartedThis trap is sent when Pki Certificate Request has started. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.93 |
transientPkiCertRequestCompletedThis trap is sent when Pki Certificate Request has completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.94 |
transientPkiCertRequestFailedThis trap is sent when Pki Certificate Request has failed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.95 |
alarmCertExceededThis trap is sent when a Certificate has exceeded its Validity Period. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.96 |
alarmCertNearlyExceededThis trap is sent when a Certificate soon will exceed its Validity Period. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.97 |
transientLinkChangedThis trap is sent when an Add-Drop Link Layout has changed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.98 |
alarmAddDropLinkLossHighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portThresAddDropHigh. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.99 |
alarmAddDropLinkLossDevThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portThresAddDropDeviation. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.100 |
alarmEmailNotifyAddDropLinkLossHighThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portThresAddDropHigh and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.101 |
alarmEmailNotifyAddDropLinkLossDevThis trap is sent if difference between monitorPointLossCurrentLoss and monitorPointLossFpLoss exceeded portThresAddDropDeviation and the corresponding automatic fault analysis measurement has been completed. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.102 |
segmentCreatedThis trap is sent when a Segment was created. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.103 |
segmentDeletedThis trap is sent when a Segment was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.104 |
alarmEquipmentRemovedThis trap is sent if the Equipment is not reachable NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.105 |
alarmEquipmentFaultThis trap is sent if the Equipment is faulty NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.106 |
alarmAttenuationHighThis trap is sent if the Optical Connection from this Port to its extender has a too high loss NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.107 |
internalExtensionChannelCreatedThis trap is sent when a internalExtensionChannel including the correspondig set of Ports was created, with first and last aidString. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.108 |
internalExtensionChannelDeletedThis trap is sent when a internalExtensionChannel including the correspondig set of Ports was deleted, with first and last aidString. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.109 |
portExtenderCreatedThis trap is sent when a Portextender was created. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.110 |
portExtenderDeletedThis trap is sent when a Portextender was deleted. NOTIFICATION-TYPE .1.3.6.1.4.1.2544.1.14.0.111 |
alarm OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.1 |
alarmTable SEQUENCE OF AlarmEntry .1.3.6.1.4.1.2544.1.14.1.1 |
alarmEntry AlarmEntry .1.3.6.1.4.1.2544.1.14.1.1.1 |
alarmSourceEquals portId of the concerned port if the alarm is port-specific. Zero otherwise. Integer32 .1.3.6.1.4.1.2544.1.14.1.1.1.1 |
alarmTypeType of alarm. Fsp3000almAlarmListType .1.3.6.1.4.1.2544.1.14.1.1.1.2 |
alarmSeverityValue of severity.ro TrapAlarmSeverity (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.1.1.1.3 |
alarmTimeStampTimestamp of alarm.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.1.1.1.4 |
alarmSeverityTable SEQUENCE OF AlarmSeverityEntry .1.3.6.1.4.1.2544.1.14.1.2 |
alarmSeverityEntry AlarmSeverityEntry .1.3.6.1.4.1.2544.1.14.1.2.1 |
alarmSeverityTypeType of severity. Fsp3000almAlarmListType .1.3.6.1.4.1.2544.1.14.1.2.1.2 |
alarmSeverityValueValue of severity.rw TrapAlarmSeverity (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.1.2.1.3 |
alarmEmailNotifyTable SEQUENCE OF AlarmEmailNotifyEntry .1.3.6.1.4.1.2544.1.14.1.3 |
alarmEmailNotifyEntry AlarmEmailNotifyEntry .1.3.6.1.4.1.2544.1.14.1.3.1 |
alarmEmailNotifyTypeType of alarm. Fsp3000almAlarmListType .1.3.6.1.4.1.2544.1.14.1.3.1.1 |
alarmEmailNotifyExternalIdExternalId of port.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.2 |
alarmEmailNotifyIdId of alarm.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.3 |
alarmEmailNotifySeverityValue of severity.ro Enumeration .1.3.6.1.4.1.2544.1.14.1.3.1.4 |
alarmEmailNotifyTimeStampTimestamp of alarm creation.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.1.3.1.5 |
alarmEmailNotifyFaultPositionFault position in kilometers.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.6 |
alarmEmailNotifyFaultTypeFault type of alarm.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.7 |
alarmEmailNotifyStateState of alarm.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.8 |
alarmEmailNotifyEventAlarm event.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.9 |
alarmEmailNotifyEventTimeStampTimestamp of alarm event.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.1.3.1.10 |
alarmEmailNotifyFaultAnalysisReferenceFault analysis reference number.ro Integer32 .1.3.6.1.4.1.2544.1.14.1.3.1.11 |
alarmEmailNotifyCorrectedFaultPosFault analysis corrected position.ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.12 |
alarmEmailNotifyFaultPosLatitudeThe latitude of the fault position in decimal degrees (-90 to 90 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.13 |
alarmEmailNotifyFaultPosLongitudeThe longitude of the fault position in decimal degrees (-180 to 180 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.1.3.1.14 |
alarmDescriptionTable SEQUENCE OF AlarmDescriptionEntry .1.3.6.1.4.1.2544.1.14.1.4 |
alarmDescriptionEntry AlarmDescriptionEntry .1.3.6.1.4.1.2544.1.14.1.4.1 |
alarmDescriptionNameName of alarm.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.1.4.1.2 |
lossAlarmsMasking1 disable / 2 enable Alarmmasking LinkLoss>LinkLossNearly>Fast>Medium>Slow this attribute is deprecated, it can be set but it has no effect.rw Enumeration .1.3.6.1.4.1.2544.1.14.1.5 |
device OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.2 |
shelf OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.2.1 |
shelfUnitNameOfficial Equipment Namero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.1 |
firmwarePackageRevFirmware Package Revision Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.2 |
hardwareRevEquipment Revision Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.3 |
fpgaRevThe active FPGA version on the devicero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.4 |
serialNumberEquipment Serial Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.5 |
partNumberPart Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.6 |
cleiCodeCommon Language Equipment Identifierro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.7 |
vendorIdOEM Vendor Codero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.8 |
inventoryTypeType of the physical entityro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.9 |
universalSerialIdentUniversal Serial Identifierro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.1.10 |
tempCPUCurrent CPU temperature (in 0.1 degree Celsius).ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.11 |
thresholdMaxTempCPUUpper threshold for CPU temperature. If tempCPU is higher than threshold, the system will send a trap.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.12 |
tempBoard1Current temperature of the management board (in 0.1 degree Celsius). Not available on 16ALM-1650D.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.13 |
thresholdMaxTempBoard1Upper threshold for board temperature. If tempBoard is higher than threshold, the system will send a trap. Not available on 16ALM-1650D.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.14 |
tempBoard2ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.15 |
thresholdMinTempBoard2ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.16 |
thresholdMaxTempBoard2ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.17 |
tempLaserNot available on 16ALM-1650D.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.18 |
thresholdMinTempLaserNot available on 16ALM-1650D.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.19 |
thresholdMaxTempLaserNot available on 16ALM-1650D.ro Integer32 UNITS "0.1 C" .1.3.6.1.4.1.2544.1.14.2.1.20 |
aidStringName of the devicero OCTET STRING .1.3.6.1.4.1.2544.1.14.2.1.21 |
shelfNameName of the devicerw DisplayString .1.3.6.1.4.1.2544.1.14.2.1.22 |
portTableTable of optical ports. SEQUENCE OF PortEntry .1.3.6.1.4.1.2544.1.14.2.2 |
portEntry PortEntry .1.3.6.1.4.1.2544.1.14.2.2.1 |
portId Integer32 .1.3.6.1.4.1.2544.1.14.2.2.1.1 |
portAdminStateAdministrative State of the port. Setting to mgt disables the service. It is, however, manadatory to set state to mgt to perform other measurement affecting actions (e.g. changing thresholds values).rw Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.2 |
portOperStateOperational State of the port. The value of the port is set to anr if the at least one of the following alarms are set on this port: alarmMonNotRunning, alarmFpMissing.ro Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.3 |
portNameName of the link.rw DisplayString .1.3.6.1.4.1.2544.1.14.2.2.1.4 |
portAidStringro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.2.2.1.5 |
portRemarkPort remark.rw DisplayString .1.3.6.1.4.1.2544.1.14.2.2.1.6 |
portFingerprintModeType of the current Fingerprint.ro Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.7 |
portPriorityPriority of the Port.rw Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.8 |
portGisConfiguredThis variable is set to 'yes' when a route is configured in the internal ALM GIS for this port. Can be set to 'no' to delete the routerw Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.9 |
portConnectedInternalChannelCurrent mapping, i.e. internal optical port on Port Extender, which the port is connected to, 'empty' if nonerw IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.2.2.1.10 |
portPmDataThis value needs to be set to 2 to enable perfomance monitor data collection, there is a maximum amount of ports, which can be selected.rw Enumeration .1.3.6.1.4.1.2544.1.14.2.2.1.11 |
monitoringItems OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.2.3 |
feederLengthTable SEQUENCE OF FeederLengthEntry .1.3.6.1.4.1.2544.1.14.2.3.1 |
feederLengthEntry FeederLengthEntry .1.3.6.1.4.1.2544.1.14.2.3.1.1 |
feederLengthDistance in decimeter up to the splitter.rw Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.2.3.1.1.1 |
monitorPointTableTable of optical ports. SEQUENCE OF MonitorPointEntry .1.3.6.1.4.1.2544.1.14.2.3.2 |
monitorPointEntry MonitorPointEntry .1.3.6.1.4.1.2544.1.14.2.3.2.1 |
mpId Integer32 .1.3.6.1.4.1.2544.1.14.2.3.2.1.1 |
monitorPointPosPosition of the Monitor Point in decimeter.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.2.3.2.1.2 |
monitorPointStateThis variable is set to '1' when this Monitor Point is active. If this Monitor Point is inactive this variable is set to '0'.rw Enumeration .1.3.6.1.4.1.2544.1.14.2.3.2.1.3 |
monitorPointNameName of the Monitor Point.rw DisplayString .1.3.6.1.4.1.2544.1.14.2.3.2.1.4 |
monitorPointAidStringro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.2.3.2.1.5 |
monitorPointRemarkRemark of the Monitor Point.rw DisplayString .1.3.6.1.4.1.2544.1.14.2.3.2.1.6 |
monitorPointExternalIdThe externalId of the Monitor Point.rw DisplayString .1.3.6.1.4.1.2544.1.14.2.3.2.1.7 |
extShelfTableTable of external Shelves aka Port Extenders. SEQUENCE OF ExtShelfEntry .1.3.6.1.4.1.2544.1.14.2.4 |
extShelfEntry ExtShelfEntry .1.3.6.1.4.1.2544.1.14.2.4.1 |
extShelfNoNumber of external shelf Integer32 .1.3.6.1.4.1.2544.1.14.2.4.1.1 |
extShelfRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.2.4.1.2 |
extShelfTypeType of the external shelf, i.e. ALM-EXT-16MPO24-8LA or ALM-EXT-96LA-2LArw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.2.4.1.3 |
extShelfAidStringAID: SHEXT-1 .. SHEXT-8ro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.2.4.1.4 |
extShelfInternalId91, ..., 98 the internal ID used for the alarm tablero Integer32 .1.3.6.1.4.1.2544.1.14.2.4.1.5 |
extShelfNrInternalPortsNumber of internal optical portsro Integer32 (2|8) .1.3.6.1.4.1.2544.1.14.2.4.1.6 |
extShelfNrMonitorPortsNumber of Monitor Ports on the Port Extenderro Integer32 (96|384) .1.3.6.1.4.1.2544.1.14.2.4.1.7 |
extShelfNameName of the Port Extenderrw DisplayString .1.3.6.1.4.1.2544.1.14.2.4.1.8 |
extShelfRemarkRemark of the Port Extenderrw DisplayString .1.3.6.1.4.1.2544.1.14.2.4.1.9 |
entityPortTableTable of Monitor Ports SEQUENCE OF EntityPortEntry .1.3.6.1.4.1.2544.1.14.2.5 |
entityPortEntry EntityPortEntry .1.3.6.1.4.1.2544.1.14.2.5.1 |
entityPortInternalNoNumber of the internal optical port, A .. H as ASCII decimal code 65, .., 72; 0 for the Monitor Ports on the ALM itself Integer32 (0|65..72) .1.3.6.1.4.1.2544.1.14.2.5.1.1 |
entityPortPortNoNumber of Monitor Port, 1 .. 16 on 16ALM, 1 .. 64 on 64ALM, 1 .. 48 on Port Extenders Integer32 .1.3.6.1.4.1.2544.1.14.2.5.1.2 |
entityPortAidStringAID: MCH-1-x for Monitor Ports on the ALM, MCH-Ex-X-y for Monitor Ports on Port Extenders, ICH-Ex-X for internal optical ports on Port Extendersro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.2.5.1.3 |
entityPortPortIdInternal port ID: 1 .. 16|64 for Monitor Ports on ALM itself 100, 150, 200, ... for internal optical ports on Port Extender 101, ..., 148, 151, ..., 198, ........, 851, ..., 898 for Monitor Ports on Port Extenderro Integer32 .1.3.6.1.4.1.2544.1.14.2.5.1.4 |
measurement OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.3 |
measurementLossTable SEQUENCE OF MeasurementLossEntry .1.3.6.1.4.1.2544.1.14.3.1 |
measurementLossEntry MeasurementLossEntry .1.3.6.1.4.1.2544.1.14.3.1.1 |
measurementLossIndexro Integer32 .1.3.6.1.4.1.2544.1.14.3.1.1.1 |
measurementLossLinkLossLink loss at termination in tenth of dB.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.1.1.2 |
measurementLossLinkFaultLocFault location in decimetres. If there is no current Fault Position the value is -1ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.1.1.3 |
measurementLossLinkFaultLocResResolution of the fault location measurement in decimetres.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.1.1.4 |
measurementLossDevFastro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.1.1.5 |
measurementLossDevMediumro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.1.1.6 |
measurementLossDevSlowro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.1.1.7 |
measurementLossDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.1.1.8 |
histMeasLoss15MinTable SEQUENCE OF HistMeasLoss15MinEntry .1.3.6.1.4.1.2544.1.14.3.4 |
histMeasLoss15MinEntryEntry of histMeasLoss15MinTable HistMeasLoss15MinEntry .1.3.6.1.4.1.2544.1.14.3.4.1 |
histMeasLoss15MinNumberA number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. Integer32 .1.3.6.1.4.1.2544.1.14.3.4.1.1 |
histMeasLoss15MinLowLowest link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.4.1.2 |
histMeasLoss15MinMeanMean link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.4.1.3 |
histMeasLoss15MinHighHighest link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.4.1.4 |
histMeasLoss15MinValidFlagValid Flagro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.4.1.5 |
histMeasLoss15MinTimeStampTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.4.1.6 |
histMeasLoss15MinLengthLink legthro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.4.1.7 |
histMeasLoss15MinLossPerKmLowLowest link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.4.1.8 |
histMeasLoss15MinLossPerKmMeanMean link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.4.1.9 |
histMeasLoss15MinLossPerKmHighHighest link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.4.1.10 |
histMeasLoss1DayTable SEQUENCE OF HistMeasLoss1DayEntry .1.3.6.1.4.1.2544.1.14.3.5 |
histMeasLoss1DayEntryEntry of histMeasLoss1DayTable HistMeasLoss1DayEntry .1.3.6.1.4.1.2544.1.14.3.5.1 |
histMeasLoss1DayNumberA number, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 1 day interval. Integer32 .1.3.6.1.4.1.2544.1.14.3.5.1.1 |
histMeasLoss1DayLowLowest link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.5.1.2 |
histMeasLoss1DayMeanMean link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.5.1.3 |
histMeasLoss1DayHighHighest link lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.5.1.4 |
histMeasLoss1DayValidFlagValid Flagro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.5.1.5 |
histMeasLoss1DayTimeStampTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.5.1.6 |
histMeasLoss1DayLengthLink legthro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.5.1.7 |
histMeasLoss1DayLossPerKmLowLowest link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.5.1.8 |
histMeasLoss1DayLossPerKmMeanMean link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.5.1.9 |
histMeasLoss1DayLossPerKmHighHighest link loss per kmro Integer32 UNITS "0.01 dB/km" .1.3.6.1.4.1.2544.1.14.3.5.1.10 |
portThresTable SEQUENCE OF PortThresEntry .1.3.6.1.4.1.2544.1.14.3.6 |
portThresEntry PortThresEntry .1.3.6.1.4.1.2544.1.14.3.6.1 |
portThresDeviationFastportThresDeviationFastrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.2 |
portThresDeviationMediumportThresDeviationMedium This attribute is deprecated, it can be set but is has no effect.rw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.3 |
portThresDeviationSlowportThresDeviationSlow This attribute is deprecated, it can be set but is has no effect.rw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.4 |
portThresBudgetportThresBudgetrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.5 |
portThresCloseToBudgetportThresCloseToBudgetrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.6 |
portMonitorThresLossBudgetportMonitorThresLossBudgetrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.7 |
portMonitorThresDeviationportMonitorThresDeviationrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.8 |
portSensor1ThresportSensor1Thresrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.9 |
portSensor2ThresportSensor2Thresrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.10 |
portAutoThresAdjustment1 disable / 2 enable automatic adjustment of ThresBudget/ThresCloseToBudget with the following marginsrw Enumeration .1.3.6.1.4.1.2544.1.14.3.6.1.11 |
portThresBudgetMarginportThresBudgetMarginrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.12 |
portThresCloseToBudgetMarginportThresCloseToBudgetMarginrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.13 |
portThresAddDropHighportThresAddDropHighrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.14 |
portThresAddDropDeviationportThresAddDropDeviationrw Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.6.1.15 |
portPeriodLossDevTable SEQUENCE OF PortPeriodLossDevEntry .1.3.6.1.4.1.2544.1.14.3.7 |
portPeriodLossDevEntry PortPeriodLossDevEntry .1.3.6.1.4.1.2544.1.14.3.7.1 |
portPeriodLossDevFastThis attribute is deprecated it can be set but it has no effect.rw Integer32 UNITS "min" .1.3.6.1.4.1.2544.1.14.3.7.1.1 |
portPeriodLossDevMediumThis attribute is deprecated it can be set but it has no effect.rw Integer32 UNITS "h" .1.3.6.1.4.1.2544.1.14.3.7.1.2 |
portPeriodLossDevSlowThis attribute is deprecated it can be set but it has no effect.rw Integer32 UNITS "d" .1.3.6.1.4.1.2544.1.14.3.7.1.3 |
measurementFpTable SEQUENCE OF MeasurementFpEntry .1.3.6.1.4.1.2544.1.14.3.8 |
measurementFpEntry MeasurementFpEntry .1.3.6.1.4.1.2544.1.14.3.8.1 |
measurementFpIndex Integer32 .1.3.6.1.4.1.2544.1.14.3.8.1.1 |
measurementFpRefractiveIndexRefractive index multiplied by 1000000.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.8.1.2 |
measurementFpExternalOffsetExternal offset length in meters.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.8.1.3 |
measurementFpCouplerLossCoupler loss in tenth of dB.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.8.1.4 |
measurementFpLinkLossLink loss at reflector in tenth of dB.ro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.8.1.5 |
measurementFpLineEndPosPosition of the reflector in decimetres.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.8.1.6 |
measurementFpDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.8.1.7 |
measurementFpNumConnectorsEquals -2147483648 if loss guidance was not enabled during fingerprint creation.ro Integer32 (0..20 | -2147483648) .1.3.6.1.4.1.2544.1.14.3.8.1.8 |
measurementFpNumSplicesEquals -2147483648 if loss guidance was not enabled during fingerprint creation.ro Integer32 (0..20 | -2147483648) .1.3.6.1.4.1.2544.1.14.3.8.1.9 |
measurementFpMaxLaserPowerMaximal laser power in 0.01dBm. Only available on 16ALM-1650D.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.8.1.10 |
measurementFpFastModeIf this variable is 'enabled' faster OTDR measurements are activated with less accuracy.ro Enumeration .1.3.6.1.4.1.2544.1.14.3.8.1.11 |
measurementFpMonitoringModeMeasurement method for monitoring.ro Enumeration .1.3.6.1.4.1.2544.1.14.3.8.1.12 |
measurementFpTrafficDetectedThis object is available if traffic check is enabled.ro Enumeration .1.3.6.1.4.1.2544.1.14.3.8.1.13 |
measurementFaTable SEQUENCE OF MeasurementFaEntry .1.3.6.1.4.1.2544.1.14.3.9 |
measurementFaEntry MeasurementFaEntry .1.3.6.1.4.1.2544.1.14.3.9.1 |
measurementFaIndex Integer32 .1.3.6.1.4.1.2544.1.14.3.9.1.1 |
measurementFaLinkLossLink loss at reflector in tenth of dB.ro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.9.1.2 |
measurementFaFaultPosFault position in decimetres.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.9.1.3 |
measurementFaDeprecatedThis variable is set to 'yes' when this Fault Analysis refers to old fingerprint, i.e. new finger print was generated after this Fault Analysis had been performed.ro Enumeration .1.3.6.1.4.1.2544.1.14.3.9.1.4 |
measurementFaDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.9.1.5 |
measurementFaCorrectedFaultPosCorrected fault position in decimetres. If no customized events were added this entry equals -2147483648.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.9.1.6 |
measurementFaFaultPosLatitudeThe latitude of the fault position in decimal degrees (-90 to 90 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.3.9.1.7 |
measurementFaFaultPosLongitudeThe longitude of the fault position in decimal degrees (-180 to 180 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.3.9.1.8 |
measurementOtdrTable SEQUENCE OF MeasurementOtdrEntry .1.3.6.1.4.1.2544.1.14.3.10 |
measurementOtdrEntry MeasurementOtdrEntry .1.3.6.1.4.1.2544.1.14.3.10.1 |
measurementOtdrIndex Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.1 |
measurementOtdrLengthMeasurement length in meters.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.2 |
measurementOtdrExternalOffsetExternal offset length in meters.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.3 |
measurementOtdrRefractiveIndexRefractive index multiplied by 1000000.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.4 |
measurementOtdrPowerLevelPower level in 0.01dBm. Not available on 16ALM-1650D.ro Integer32 (-2000..2000) UNITS "0.01 dBm" .1.3.6.1.4.1.2544.1.14.3.10.1.5 |
measurementOtdrPulseWidthPulse width in ns.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.6 |
measurementOtdrAverageRateAverage rate (0=512,1=1024,2=2048,3=4096,4=8192,5=16384,6=32768,7=65536). Not available on 16ALM-1650D.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.7 |
measurementOtdrDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.10.1.8 |
measurementOtdrMaxLaserPowerMaximal laser power in 0.01dBm. Not available on 16ALM.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.9 |
measurementOtdrLinkLengthLength of the optical link in meters. Not available on 16ALM.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.10 |
measurementOtdrMeasTimeMeasurement time in seconds. Not available on 16ALM.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.10.1.11 |
measurementAutoFaTable SEQUENCE OF MeasurementAutoFaEntry .1.3.6.1.4.1.2544.1.14.3.11 |
measurementAutoFaEntry MeasurementAutoFaEntry .1.3.6.1.4.1.2544.1.14.3.11.1 |
measurementAutoFaIndex Integer32 .1.3.6.1.4.1.2544.1.14.3.11.1.1 |
measurementAutoFaReferenceFault analysis reference number.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.11.1.2 |
measurementAutoFaLinkLossLink loss at reflector in tenth of dB.ro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.11.1.3 |
measurementAutoFaFaultPosFault position in decimetres.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.11.1.4 |
measurementAutoFaDeprecatedThis variable is set to 'yes' when this Fault Analysis refers to old fingerprint, i.e. new finger print was generated after this Fault Analysis had been performed.ro Enumeration .1.3.6.1.4.1.2544.1.14.3.11.1.5 |
measurementAutoFaDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.11.1.6 |
measurementAutoFaCorrectedFaultPosCorrected fault position in decimetres. If no customized events were added this entry equals -2147483648.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.11.1.7 |
measurementAutoFaFaultPosLatitudeThe latitude of the fault position in decimal degrees (-90 to 90 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.3.11.1.8 |
measurementAutoFaFaultPosLongitudeThe longitude of the fault position in decimal degrees (-180 to 180 degree).ro DisplayString .1.3.6.1.4.1.2544.1.14.3.11.1.9 |
monitorPointLossTable SEQUENCE OF MonitorPointLossEntry .1.3.6.1.4.1.2544.1.14.3.12 |
monitorPointLossEntry MonitorPointLossEntry .1.3.6.1.4.1.2544.1.14.3.12.1 |
monitorPointLossCurrentLossCurrent loss at monitor point in tenth of dB.ro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.12.1.1 |
monitorPointLossFpLossFingerprint loss at monitor point in tenth of dB.ro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.12.1.2 |
monitorPointLossDataTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.12.1.3 |
histMonitorPointLoss15MinTable SEQUENCE OF HistMonitorPointLoss15MinEntry .1.3.6.1.4.1.2544.1.14.3.13 |
histMonitorPointLoss15MinEntryEntry of histMonitorPointLoss15MinTable HistMonitorPointLoss15MinEntry .1.3.6.1.4.1.2544.1.14.3.13.1 |
histMonitorPointLoss15MinNumberA number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. Only existing values will be shown. Integer32 .1.3.6.1.4.1.2544.1.14.3.13.1.1 |
histMonitorPointLoss15MinLowLowest monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.13.1.2 |
histMonitorPointLoss15MinMeanMean monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.13.1.3 |
histMonitorPointLoss15MinHighHighest monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.13.1.4 |
histMonitorPointLoss15MinValidValid Flagro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.13.1.5 |
histMonitorPointLoss15MinTimeStampTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.13.1.6 |
histMonitorPointLoss1DayTable SEQUENCE OF HistMonitorPointLoss1DayEntry .1.3.6.1.4.1.2544.1.14.3.14 |
histMonitorPointLoss1DayEntryEntry of histMonitorPointLoss1DayTable HistMonitorPointLoss1DayEntry .1.3.6.1.4.1.2544.1.14.3.14.1 |
histMonitorPointLoss1DayNumberA number, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 1 day interval. Only existing values will be shown. Integer32 .1.3.6.1.4.1.2544.1.14.3.14.1.1 |
histMonitorPointLoss1DayLowLowest monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.14.1.2 |
histMonitorPointLoss1DayMeanMean monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.14.1.3 |
histMonitorPointLoss1DayHighHighest monitor point lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.14.1.4 |
histMonitorPointLoss1DayValidValid Flagro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.14.1.5 |
histMonitorPointLoss1DayTimeStampTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.14.1.6 |
measurementFpEventTable SEQUENCE OF MeasurementFpEventEntry .1.3.6.1.4.1.2544.1.14.3.15 |
measurementFpEventEntryEntry of measurementFpEventEntry MeasurementFpEventEntry .1.3.6.1.4.1.2544.1.14.3.15.1 |
measurementFpEventId Integer32 .1.3.6.1.4.1.2544.1.14.3.15.1.1 |
measurementFpEventPositionPosition in decimeter.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.15.1.2 |
measurementFpEventReflectanceReflectance in tenth of dBro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.15.1.3 |
measurementFpEventAttenuationAttenuation in tenth of dBro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.15.1.4 |
measurementFpEventRemarkrw DisplayString .1.3.6.1.4.1.2544.1.14.3.15.1.5 |
customizedFpEventTable SEQUENCE OF CustomizedFpEventEntry .1.3.6.1.4.1.2544.1.14.3.16 |
customizedFpEventEntryEntry of customizedFpEventEntry CustomizedFpEventEntry .1.3.6.1.4.1.2544.1.14.3.16.1 |
customizedFpEventIdro Integer32 .1.3.6.1.4.1.2544.1.14.3.16.1.1 |
customizedFpEventRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.16.1.2 |
customizedFpEventCorrectedPositionCorrected position in tenth of meter.rw Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.16.1.3 |
customizedFpEventRemarkRemark.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.3.16.1.4 |
customizedFpEventOtdrIdOTDR fingerprint event ID. If no mapping between GIS and OTDR event was found this entry equals -2147483648.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.16.1.5 |
customizedFpEventOtdrPositionOTDR distance in tenth of meter is either filled when event mapped to a fingerprint event or potentially added when not mapped.rw Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.16.1.6 |
customizedFpEventLayoutId0 for all fingerprinttyps other then AddDropFiber. Values great the 0 are then mapping to a AddDropFiberLayoutLine between the coupler and reflector of this id.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.16.1.7 |
mergedFpEventTable SEQUENCE OF MergedFpEventEntry .1.3.6.1.4.1.2544.1.14.3.17 |
mergedFpEventEntryEntry of mergedFpEventEntry MergedFpEventEntry .1.3.6.1.4.1.2544.1.14.3.17.1 |
mergedFpEventId Integer32 .1.3.6.1.4.1.2544.1.14.3.17.1.1 |
mergedFpEventCustomizedEventIdCustomized fingerprint event ID.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.17.1.2 |
mergedFpEventOtdrIdOTDR fingerprint event ID.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.17.1.3 |
mergedFpEventCorrectedPositionCorrected position in tenth of meter.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.17.1.4 |
mergedFpEventOtdrPositionOTDR distance in tenth of meter is either filled when event mapped to a fingerprint event or potentially added when not mapped.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.17.1.5 |
mergedFpEventRemarkRemark.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.3.17.1.6 |
linkLayoutEventTable SEQUENCE OF LinkLayoutEventEntry .1.3.6.1.4.1.2544.1.14.3.18 |
linkLayoutEventEntryEntry of linkLayoutEventEntry LinkLayoutEventEntry .1.3.6.1.4.1.2544.1.14.3.18.1 |
linkLayoutEventIdro Integer32 .1.3.6.1.4.1.2544.1.14.3.18.1.1 |
linkLayoutEventRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.18.1.2 |
linkLayoutEventMpIdMonitorPoint event ID.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.18.1.3 |
linkLayoutEventFpEventIdFingerprint event ID of matching coupler.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.18.1.4 |
linkLayoutEventCustomizedEventIdCustomized Event ID of matching coupler.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.18.1.5 |
linkLayoutEventFaultPosFault position starting from last coupler in decimetres, is negative if the fault position is before the position of the corresponding coupler.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.18.1.6 |
linkLayoutEventCorrectedFaultPosCorrected fault position starting from last coupler in decimetres. If no customized events were added this entry equals -2147483648.ro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.18.1.7 |
segmentTable SEQUENCE OF SegmentEntry .1.3.6.1.4.1.2544.1.14.3.19 |
segmentEntryEntry of segmentTable SegmentEntry .1.3.6.1.4.1.2544.1.14.3.19.1 |
segmentIdA number which identifies the Segment. The sequenze does not have to be without holes.Creating a new segment needs a free number.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.19.1.1 |
segmentRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.19.1.2 |
segmentStartEventIdFingerpintId for the starting event of the segment . 0 for measuring from link start.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.19.1.3 |
segmentStopEventIdFingerpintId for the stoping event of the segment . 0 for measuring from link start.rw Integer32 .1.3.6.1.4.1.2544.1.14.3.19.1.4 |
segmentStartCorrectionOffest for the segment start realtiv to the event (0 from link start) , can be + or - , regadles of value the segment can't escape the link boundrys.rw Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.19.1.5 |
segmentStopCorrectionOffest for the segment stop realtiv to the event (0 from link start), can be + or - , regadles of value the segment can't escape the link boundrys.rw Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.19.1.6 |
segmentRemarkRemark.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.3.19.1.7 |
segmentFpLengthSegment length in decimeterro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.19.1.8 |
segmentFpLossSegment lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.19.1.9 |
segmentFpLossPerKmSegment loss per kmro Integer32 UNITS "0.01 dB" .1.3.6.1.4.1.2544.1.14.3.19.1.10 |
histSegmentTable SEQUENCE OF HistSegmentEntry .1.3.6.1.4.1.2544.1.14.3.20 |
histSegmentEntryEntry of histSegmentTable HistSegmentEntry .1.3.6.1.4.1.2544.1.14.3.20.1 |
histSegmentNumberA number between 1 and 30, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. Only existing values will be shown. Integer32 .1.3.6.1.4.1.2544.1.14.3.20.1.1 |
histSegmentLengthSegment length in decimeterro Integer32 UNITS "0.1 m" .1.3.6.1.4.1.2544.1.14.3.20.1.2 |
histSegmentLossSegment lossro Integer32 UNITS "0.1 dB" .1.3.6.1.4.1.2544.1.14.3.20.1.3 |
histSegmentLossPerKmSegment loss per kmro Integer32 UNITS "0.01 dB" .1.3.6.1.4.1.2544.1.14.3.20.1.4 |
histSegmentUncertainSet if the loss value was to close to the noisero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.20.1.5 |
histSegmentTimeStampTimestampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.20.1.6 |
internalChannelLossTable SEQUENCE OF InternalChannelLossEntry .1.3.6.1.4.1.2544.1.14.3.21 |
internalChannelLossEntryEntry of internalChannelLossTable InternalChannelLossEntry .1.3.6.1.4.1.2544.1.14.3.21.1 |
internalChannelLossValueLink loss at termination in tenth of dB.ro Integer32 .1.3.6.1.4.1.2544.1.14.3.21.1.1 |
internalChannelLossTimeStampro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.3.21.1.2 |
eventLogs OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.4 |
eventsLoggedThis value is the sum of all notified events (trap counter). It is also the event number of the most recent event (eventLogIndex) found in the eventLog tables. It can, for example, be used to check if a notification (trap) is lost. The value is reset to 0 after a cold start. The counter is increased even if no trap sinks are specified.ro Unsigned32 .1.3.6.1.4.1.2544.1.14.4.1 |
eventLogTableTable of events issued by the NE's SNMP agent. The eventLog entries are read-only. SEQUENCE OF EventLogEntry .1.3.6.1.4.1.2544.1.14.4.2 |
eventLogEntryEntries in the eventLog Table. Enterprise traps are always logged; logging of Generic traps is product specific. EventLogEntry .1.3.6.1.4.1.2544.1.14.4.2.1 |
eventLogIndexThe associated neEventsLogged counter for the logged event (trap). Unsigned32 .1.3.6.1.4.1.2544.1.14.4.2.1.1 |
eventLogTimeStampThe NE Date and Time when the event (trap) occurred. This object is used in the trap varbind.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.2.1.2 |
eventLogNotificationOIDThe NOTIFICATION-TYPE object identifier of the event that occurred. The last part of the OID corresponds to the specific trap type value in the trap PDU.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.4.2.1.3 |
eventLogIdentityTranslationTranslation of entPhysicalIndex/ifIndex or other identifier to a string used in the trap varbind following the timestamp varbind.ro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.4.2.1.4 |
eventLogVarTableTable of variables corresponding to events logged in the eventLog. SEQUENCE OF EventLogVarEntry .1.3.6.1.4.1.2544.1.14.4.3 |
eventLogVarEntryEntries in the eventLogVar Table. An entry appears in this table for each variable in the varbind list of an entry in the eventLogTable. For an event having no variables, no entries are found in this table. EventLogVarEntry .1.3.6.1.4.1.2544.1.14.4.3.1 |
eventLogVarIndexA monotonically increasing integer, starting at 1 for a given eventLogIndex, for indexing a variable contained in the varbind list of a logged event. Unsigned32 .1.3.6.1.4.1.2544.1.14.4.3.1.1 |
eventLogVarIdThe object identifier of the variable in the varbind list.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.4.3.1.2 |
eventLogVarTypeThe type of variable. One and only one of the value objects that follow must be instantiated, based on this type. The used types depend on the enterprise traps defined for the specific product.ro Enumeration .1.3.6.1.4.1.2544.1.14.4.3.1.3 |
eventLogVarInteger32ValThe value when eventLogVarType is 'integer32'. Integer32 is also used to represent INTEGER types. Otherwise, 0 is returned.ro Integer32 .1.3.6.1.4.1.2544.1.14.4.3.1.4 |
eventLogVarIpAddressValThe value when eventLogVarType is 'ipAddress'. Otherwise, an empty address is returned.ro IpAddress .1.3.6.1.4.1.2544.1.14.4.3.1.5 |
eventLogVarOctetStringValThe value when eventLogVarType is 'octetString'. OctetString is used for all string types, including DisplayString, SnmpAdminString and DateAndTime. Otherwise, an empty string is returned.ro OCTET STRING .1.3.6.1.4.1.2544.1.14.4.3.1.6 |
eventLogVarOidValThe value when eventLogVarType is 'objectId'. Otherwise, an objectId { 0.0 } is returned.ro OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.4.3.1.7 |
eventLogVarCounter64ValThe value when eventLogVarType is 'counter64'.ro Counter64 .1.3.6.1.4.1.2544.1.14.4.3.1.8 |
eventLogVarUnsigned32ValThe value when eventLogVarType is 'unsigned32'.ro Unsigned32 .1.3.6.1.4.1.2544.1.14.4.3.1.10 |
trapsinkTableTable of Trapsinks. A trapsinkTable entry can be created, deleted or modified via the SNMP interface for a specific address and port. SEQUENCE OF TrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.4 |
trapsinkEntryEntries in the Trapsink Table. Entries are created and deleted using the trapsinkRowStatus object. The maximum of rows in this table is product specific. TrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.4.1 |
trapsinkAddressIP Address of the Management System which should receive SNMP Traps.ro IpAddress .1.3.6.1.4.1.2544.1.14.4.4.1.1 |
trapsinkPortThe port number where the specified trap sink will receive SNMP traps. Integer32 .1.3.6.1.4.1.2544.1.14.4.4.1.2 |
trapsinkCommunityCommunity String which is sent with an SNMP Trap to the Management Station. The default is 'public'.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.4.1.3 |
trapsinkRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.4.1.4 |
trapsinkVersionThe default is v2(2).rw Enumeration .1.3.6.1.4.1.2544.1.14.4.4.1.5 |
trapsinkUserNameA human readable string representing the name of the user.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.4.1.6 |
trapsinkRemarkA human readable string representing the remark for the trap sink.rw OCTET STRING .1.3.6.1.4.1.2544.1.14.4.4.1.7 |
trapsinkLifetimeLifetime of Trapsinkrw Enumeration .1.3.6.1.4.1.2544.1.14.4.4.1.8 |
ipv6TrapsinkTableTable of IPv6 Trapsinks. A ipv6TrapsinkTable entry can be created, deleted or modified via the SNMP interface for a specific address and port. SEQUENCE OF Ipv6TrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.5 |
ipv6TrapsinkEntryEntries in the IPv6 Trapsink Table. Entries are created and deleted using the ipv6TrapsinkRowStatus object. The maximum of rows in this table is product specific. Ipv6TrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.5.1 |
ipv6TrapsinkIdro Integer32 .1.3.6.1.4.1.2544.1.14.4.5.1.1 |
ipv6TrapsinkAddressIPv6 Address of the Management System which should receive SNMP Traps.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.5.1.2 |
ipv6TrapsinkPortThe port number where the specified trap sink will receive SNMP traps.rw Integer32 .1.3.6.1.4.1.2544.1.14.4.5.1.3 |
ipv6TrapsinkCommunityCommunity String which is sent with an SNMP Trap to the Management Station. The default is 'public'.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.5.1.4 |
ipv6TrapsinkRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.5.1.5 |
ipv6TrapsinkVersionThe default is v2(2).rw Enumeration .1.3.6.1.4.1.2544.1.14.4.5.1.6 |
ipv6TrapsinkUserNameA human readable string representing the name of the user.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.5.1.7 |
ipv6TrapsinkRemarkA human readable string representing the remark for the trap sink.rw OCTET STRING .1.3.6.1.4.1.2544.1.14.4.5.1.8 |
ipv6TrapsinkLifetimeLifetime of ipv6Trapsinkrw Enumeration .1.3.6.1.4.1.2544.1.14.4.5.1.9 |
sysLogRecipients OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.4.6 |
sysLogRecipient1AddressAn IPv4/IPv6 address of one syslog server.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.6.1 |
sysLogRecipient2AddressAn IPv4/IPv6 address of one syslog server.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.6.2 |
sysLogRecipient3AddressAn IPv4/IPv6 address of one syslog server.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.6.3 |
dnsTrapsinkTableTable of Trapsinks. A dnsTrapsinkTable entry can be created, deleted or modified via the SNMP interface for a specific address and port. SEQUENCE OF DnsTrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.7 |
dnsTrapsinkEntryEntries in the dns Trapsink Table. Entries are created and deleted using the dnsTrapsinkRowStatus object. The maximum of rows in this table is product specific. DnsTrapsinkEntry .1.3.6.1.4.1.2544.1.14.4.7.1 |
dnsTrapsinkIdro Integer32 .1.3.6.1.4.1.2544.1.14.4.7.1.1 |
dnsTrapsinkHostNameHost Address of the Management System which should receive SNMP Traps.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.7.1.2 |
dnsTrapsinkPortThe port number where the specified trap sink will receive SNMP traps.rw Integer32 .1.3.6.1.4.1.2544.1.14.4.7.1.3 |
dnsTrapsinkCommunityCommunity String which is sent with an SNMP Trap to the Management Station. The default is 'public'.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.7.1.4 |
dnsTrapsinkRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.4.7.1.5 |
dnsTrapsinkVersionThe default is v2(2).rw Enumeration .1.3.6.1.4.1.2544.1.14.4.7.1.6 |
dnsTrapsinkUserNameA human readable string representing the name of the user.rw DisplayString .1.3.6.1.4.1.2544.1.14.4.7.1.7 |
dnsTrapsinkRemarkA human readable string representing the remark for the trap sink.rw OCTET STRING .1.3.6.1.4.1.2544.1.14.4.7.1.8 |
dnsTrapsinkLifetimeLifetime of dnsTrapsinkrw Enumeration .1.3.6.1.4.1.2544.1.14.4.7.1.9 |
sysLogFacilityThis value is the default facility ALM labels its syslog messages.rw Enumeration .1.3.6.1.4.1.2544.1.14.4.8 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5 |
information OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.1 |
softwareVersionReports the running software version on the devicero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.1.1 |
localDateAndTimeReports the current local time on the device.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.1.2 |
releaseNumberThe release number of the product. It will have the following format: XXYYZZ. For example, release version 1.2.1 will be identified in the following way:'10201'.ro Integer32 .1.3.6.1.4.1.2544.1.14.5.1.3 |
expectedSoftwareVersionValue set by System Controller when this unit is attached to it. The value must match the softwareVersion value. In case values do not match, then trap alarmAlmPackageMismatch is sent (and alarm is raised). Trap is not sent (and alarm is not raised) when value is empty or when operationMode is set to 'standalone'.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.1.4 |
ipSettings OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.2 |
ipAddressIP address of the system (IPv4). Changes to IP Settings should be made in one SET request.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.2.1 |
subnetMaskSubnet mask. Changes to IP Settings should be made in one SET request.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.2.2 |
gatewayGateway. Changes to IP Settings should be made in one SET request.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.2.3 |
dns1DNS server 1. The address '0.0.0.0' may be used to remove an entry. Changes to IP Settings should be made in one SET request.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.2.4 |
dns2DNS server 2. The address '0.0.0.0' may be used to remove an entry. Changes to IP Settings should be made in one SET request.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.2.5 |
dhcpDynamic Host Configuration Protocol (DHCP) configuration. Changes to IP Settings should be made in one SET request but if you enable DHCP only this value and IPv6 address/dns can be set in one SET request.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.2.6 |
ipv6AddressIPv6 address of the system. Changes to IP Settings should be made in one SET request but IPv6 Address can be configured independently.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.7 |
ipv6Dns1IPv6 DNS server 1. The address '::' may be used to remove an entry. Changes to IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.8 |
ipv6Dns2IPv6 DNS server 2. The address '::' may be used to remove an entry. Changes to IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.9 |
ipSettingsUsb OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.2.10 |
ipSettingsUsbModeNeeds to be set according to the connected USB-device . Changes to USB IP Settings should be made in one SET request.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.2.10.1 |
ipSettingsUsbMobileDialInNumberOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.2 |
ipSettingsUsbMobileAPNOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.3 |
ipSettingsUsbMobileUserNameOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.4 |
ipSettingsUsbMobileUserPasswordOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.5 |
ipSettingsUsbMobileSIMPinOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.6 |
ipSettingsUsbMobileIPAddressOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.7 |
ipSettingsUsbMobileRoutingNetAddressOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.8 |
ipSettingsUsbMobileRoutingNetMaskOnly relevant for usbmode=Mobile(3). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.9 |
ipSettingsUsbLanAdapterIPAddressOnly relevant for usbmode=LanAdapter(5). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.10 |
ipSettingsUsbLanAdapterSubnetMaskOnly relevant for usbmode=LanAdapter(5). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.11 |
ipSettingsUsbLanAdapterGatewayOnly relevant for usbmode=LanAdapter(5). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.12 |
ipSettingsUsbLanAdapterRoutingNetAddressOnly relevant for usbmode=LanAdapter(5). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.13 |
ipSettingsUsbLanAdapterRoutingNetMaskOnly relevant for usbmode=LanAdapter(5). Changes to USB IP Settings should be made in one SET request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.10.14 |
ethernetPortTable SEQUENCE OF EthernetPortEntry .1.3.6.1.4.1.2544.1.14.5.2.11 |
ethernetPortEntry EthernetPortEntry .1.3.6.1.4.1.2544.1.14.5.2.11.1 |
ethernetPortIdIndex Integer32 .1.3.6.1.4.1.2544.1.14.5.2.11.1.1 |
ethernetPortIdentifierIdentifier of the Ethernetdevicero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.2.11.1.2 |
ethernetPortModeselected ethernet mode,not configurable on some hardwarerw Enumeration .1.3.6.1.4.1.2544.1.14.5.2.11.1.3 |
ethernetPortBitratecurent ethernet Bitratero Enumeration .1.3.6.1.4.1.2544.1.14.5.2.11.1.4 |
ethernetPortDuplexcurrent duplex modero Enumeration .1.3.6.1.4.1.2544.1.14.5.2.11.1.5 |
ethernetPortMtuconfigured Mturw Integer32 .1.3.6.1.4.1.2544.1.14.5.2.11.1.6 |
softwareMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.3 |
softwareMgmtFileTable SEQUENCE OF SoftwareMgmtFileEntry .1.3.6.1.4.1.2544.1.14.5.3.1 |
softwareMgmtFileEntry SoftwareMgmtFileEntry .1.3.6.1.4.1.2544.1.14.5.3.1.1 |
softwareMgmtFileIndexIndex Integer32 .1.3.6.1.4.1.2544.1.14.5.3.1.1.1 |
softwareMgmtFileSizeSize of Filero Unsigned32 UNITS "Byte" .1.3.6.1.4.1.2544.1.14.5.3.1.1.2 |
softwareMgmtFileCreationTimeCreation Timero DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.3.1.1.3 |
softwareMgmtFileVersionGeneral Release Issue Number of softwarero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.1.1.4 |
softwareMgmtFileFileNameFile Namero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.1.1.5 |
softwareMgmtFileRowStatusThe status of this row. Only active(1) and destroy(6) values are supported. New row is created when a new DB file is generated by backup action or downloaded to the storage. To remove a file from storage represented by this row, set this object destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.3.1.1.6 |
softwareMgmtRequestSet request to initiate software management related actionrw Enumeration .1.3.6.1.4.1.2544.1.14.5.3.2 |
softwareMgmtStateThe current status of the SW upgrade process. When failure is set then softwareMgmtLastError is applicable.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.3.3 |
softwareMgmtLastErrorThe latest failure in the software upgrade process. Applicable only when softwareMgmtState is set to 'failure'. NOTE: All failures that are caused by malfunctioning hardware are reported as internalError(10).ro Enumeration .1.3.6.1.4.1.2544.1.14.5.3.4 |
softwareMgmtDatabaseUsageOptions defining which database will be used after upgrade/reboot. When storage is selected then softwareMgmtDatabaseFileName must be setrw Enumeration .1.3.6.1.4.1.2544.1.14.5.3.5 |
softwareMgmtDatabaseFileNameDB filename located in the storage which will be used after SW installation when softwareMgmtDatabaseUsage is set to storage(2)rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.6 |
softwareMgmtServerAddressThe IP address of the external FTP/SCP server.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.3.7 |
softwareMgmtServerLoginThe login name on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.8 |
softwareMgmtServerPasswdThe password on the external FTP/SCP server. Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.9 |
softwareMgmtServerDirectoryThe SW file location (path) on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.10 |
softwareMgmtFileNameThe SW file name (without path) on the external FTP/SCP server or the name of the file which has been downloaded to the NE.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.11 |
softwareMgmtTransferProtocolThe transfer protocol to be used.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.3.12 |
softwareMgmtFtpPortThe TCP port number of FTP server used for file transfer. Default value is 21.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.3.13 |
softwareMgmtActionProgressOperational progress in % i.e. file transferro Integer32 (0..100 | -2147483648) UNITS "%" .1.3.6.1.4.1.2544.1.14.5.3.14 |
softwareMgmtIpv6AddressThe IPv6 address of the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.15 |
softwareMgmtScpPortThe TCP port number of SCP server used for file transfer. Default value is 22.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.3.16 |
softwareMgmtBackupPasswordOptional, the password decrypting the backup. Only used if softwareMgmtDatabaseUsage is set to storage(2) For Decryption it has to be sent together with softwareMgmtRequest Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.3.17 |
databaseMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.4 |
databaseMgmtFileTable SEQUENCE OF DatabaseMgmtFileEntry .1.3.6.1.4.1.2544.1.14.5.4.1 |
databaseMgmtFileEntry DatabaseMgmtFileEntry .1.3.6.1.4.1.2544.1.14.5.4.1.1 |
databaseMgmtFileIndexIndex Integer32 .1.3.6.1.4.1.2544.1.14.5.4.1.1.1 |
databaseMgmtFileSizeSize of Filero Unsigned32 UNITS "Byte" .1.3.6.1.4.1.2544.1.14.5.4.1.1.2 |
databaseMgmtFileCreationTimeCreation Timero DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.4.1.1.3 |
databaseMgmtFileVersionGeneral Release Issue Number of softwarero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.1.1.4 |
databaseMgmtFileFileNameFile Namero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.1.1.5 |
databaseMgmtFileRowStatusThe status of this row. Only active(1) and destroy(6) values are supported. New row is created when a new software image file downloaded to the storage. To remove a file from storage represented by this row, set this object destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.4.1.1.6 |
databaseMgmtRequestSet request to initiate software management related actionrw Enumeration .1.3.6.1.4.1.2544.1.14.5.4.2 |
databaseMgmtStateThe current status of the backup/restore DB process. When failure is set then databaseMgmtLastError is applicable.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.4.3 |
databaseMgmtLastErrorThe latest failure of the backup/restore DB process. Applicable only when databaseMgmtState is set to 'failure'. NOTE: All failures that are caused by malfunctioning hardware are reported as internalError.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.4.4 |
databaseMgmtServerAddressThe IP address of the external FTP/SCP server.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.4.5 |
databaseMgmtServerLoginThe login name on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.6 |
databaseMgmtServerPasswdThe password on the external FTP/SCP server. Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.7 |
databaseMgmtServerDirectoryThe file location (path) on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.8 |
databaseMgmtFileNameThe file name (without path and either without file name extension or with .ADB extension) on the external FTP/SCP server or the name of the file which has been downloaded to the NE. Set to empty for auto-generated filename, only available during the backup process, will be changed to the file name once the backup is startedrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.9 |
databaseMgmtTransferProtocolThe transfer protocol to be used.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.4.10 |
databaseMgmtFtpPortThe TCP port number of the FTP server used for file transfer. Default value is 21.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.4.11 |
databaseMgmtActionProgressOperational progress in % i.e. file transferro Integer32 (0..100 | -2147483648) UNITS "%" .1.3.6.1.4.1.2544.1.14.5.4.12 |
databaseMgmtIpv6AddressThe IPv6 address of the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.13 |
databaseMgmtScpPortThe TCP port number of the FTP server used for file transfer. Default value is 22.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.4.14 |
databaseMgmtBackupPasswordOptional, the password encrypting/decrypting the backup, For En-/Decryption it has to be sent together with databaseMgmtRequest. Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.4.15 |
ntpMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.5 |
ntpClientConfigNTP client configuration.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.5.1 |
ntpServerNameAddress of first NTP Server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.5.2 |
ntpServerName2Address of second NTP Server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.5.3 |
ntpServerName3Address of second NTP Server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.5.4 |
ntpTimeChangeReasonReason of Time Change (manual, ntp)ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.5.5 |
generalSettings OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.6 |
operationModeMode of operation. Switching between versions affects the available functionality of NE (e.g. user management). Switching between the modes is not service affecting and does not cause any other effects, except showing/hiding particular functionality.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.1 |
httpsPortHttps Port for webgui accessrw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.2 |
access OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.6.3 |
sshInterfaceSsh server configuration.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.3.1 |
netconfInterfaceNetconf server configuration.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.3.2 |
sshPasswordAuthenticationSsh server configuration for password interactive.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.3.3 |
generalSessionTimeoutTimeout for all sessions except snmp in minutes.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.3.4 |
snmpSessionTimeoutTimeout for snmp sessions in secondsrw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.3.5 |
maxLoginFailureDelayMaximum wait time after a fail login attempt in secondsrw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.3.6 |
passwordStrengthStrength required for user passwordsrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.3.7 |
userInfoDeletionPeriodPeriod in days after user info is deleted from logs, 0 to disable the featurerw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.3.8 |
defaultTrapsinkLifetimeDefault lifetime of Trapsinkrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.3.9 |
pki OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.6.4 |
caTablecaTable SEQUENCE OF CaEntry .1.3.6.1.4.1.2544.1.14.5.6.4.1 |
caEntryEntry of caTable CaEntry .1.3.6.1.4.1.2544.1.14.5.6.4.1.1 |
caIdro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.1 |
caRowStatusRowStatus object is used to create or delete a row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.2 |
caAliasUser Applied Descriptorrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.3 |
caScepUrlSCEP service URL. May omit the scheme, because HTTP is used by default anyway. May omit the path, then default path for MS CA will be assumed '/CertSrv/mscep/mscep.dll/pkiclient.exe'rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.4 |
caScepDomainNameDomain name for SCEP service authorization.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.5 |
caScepUserNameUser name for SCEP service authorization.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.6 |
caScepPasswordPassword for SCEP service authorization.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.7 |
caScepCertValidationSCEP certificate(s) attibutes/extensions validationrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.8 |
caScepQueryMessageOptional SCEP query message, required by some SCEP server implementations, e.g. common name of the CA/RA or any non-empty value.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.9 |
caScepCipherAlgorithmSCEP cipher algorithmrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.10 |
caScepDigestAlgorithmSCEP digest algorithmrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.11 |
caScepRequestMethodSCEP request methodrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.1.1.12 |
keyTablekeyTable SEQUENCE OF KeyEntry .1.3.6.1.4.1.2544.1.14.5.6.4.2 |
keyEntryEntry of keyTable KeyEntry .1.3.6.1.4.1.2544.1.14.5.6.4.2.1 |
keyIdro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.1 |
keyRowStatusRowStatus object is used to create or delete a row in the table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.2 |
keyAliasUser Applied Descriptorrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.3 |
keyProfileCryptographic key usage/application profile.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.4 |
keyAlgorithmCryptographic key algorithmrw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.5 |
keyLengthCryptographic key bit-length or bit-size. It is not a direct 'security level', because it depends on key algorithm in the first place.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.6 |
keySha1SHA-1 fingerprint (hash value) of dataro OCTET STRING .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.7 |
keySha256SHA-256 fingerprint (hash value) of dataro OCTET STRING .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.8 |
keyCertCommonNamePublic key certificate subject's common namerw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.9 |
keyCertAlternativeNameIpPublic key certificate subject's alternative name (IP address)rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.10 |
keyCertAlternativeNameDnsPublic key certificate subject's alternative name (DNS name)rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.11 |
keyCertKeyUsagePublic key certificate key usage (X.509 attribute)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.12 |
keyCertExtKeyUsagePublic key certificate extended key usage (X.509 attribute)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.13 |
keyCertValidityPeriodPublic key certificate requested validity period (in years), only for selfsignedrw Integer32 UNITS "y" .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.14 |
keyCertRequestChallengeCertificate signing request challenge password. When using automatic enrollment procotol (SCEP), request challenge is used to authorize initial certificate signing request.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.15 |
keyCertRenewModePublic key certificate renewal mode - either manual or automatic. In manual mode the user must trigger generation of a new certificate.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.16 |
keyCertRenewIntervalPublic key certificate renewal interval. Determines when to renew the certificate relative to current certificate's either validity period (when given in -percentage) or validity end date (+ minutes).rw Integer32 UNITS "%|min" .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.17 |
keyCertRenewRetryIntervalPublic key certificate renewal retry interval. In minutesrw Integer32 UNITS "min" .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.18 |
keyCertRenewDatePlanned date (UTC) of certificate (optionally, also key) renewal. Normally should be in the future, but might be in the past, especially in case of failure.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.19 |
keyCertWarnIntervalPublic key certificate warn periode. Determines when to warn about a certificate, relative to current certificate's either validity period (when given in -percentage) or validity end date (+ minutes)rw Integer32 .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.20 |
keyCertRequestStarts procedure of certificate signing request to be processed by a external CA.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.21 |
keyCertRequestStatusStatus of the last certificate signing requestro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.22 |
keyCaEntityIdentifier of an associated certificate authorityro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.23 |
keyCertificatesIdentifiers of associated public key certificate(s)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.2.1.24 |
certificateTablecertificateTable SEQUENCE OF CertificateEntry .1.3.6.1.4.1.2544.1.14.5.6.4.3 |
certificateEntryEntry of certificateTable CertificateEntry .1.3.6.1.4.1.2544.1.14.5.6.4.3.1 |
certificateIdro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.1 |
certificateTypePublic key certificate type.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.2 |
certificateValidityStatusPublic key certificate type and validity statusro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.3 |
certificatePurposePublic key certificate purpose/application. When associated key is available, its purpose is derived from the associated key's profile. Otherwise the purpose needs to be declared.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.4 |
certificateStatusCertificate status.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.5 |
certificateIssuerPublic key certificate issuerro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.6 |
certificateSerialNoPublic key certificate serial numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.7 |
certificateSubjectPublic key certificate subjectro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.8 |
certificateCommonNamePublic key certificate subject's common namero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.9 |
certificateValidFromStart date (UTC) of public key certificate's validity periodro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.10 |
certificateValidToEnd date (UTC) of public key certificate's validity periodro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.11 |
certificateSignAlgorithmCertificate signature hash (message digest) algorithmro Enumeration .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.12 |
certificateSha1SHA-1 fingerprint (hash value) of dataro OCTET STRING .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.13 |
certificateSha256SHA-256 fingerprint (hash value) of dataro OCTET STRING .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.14 |
certificateAlternativeNameIpPublic key certificate subject's alternative name (multiple IP addresses)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.15 |
certificateAlternativeNameDnsPublic key certificate subject's alternative name (multiple DNS names)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.16 |
certificateKeyUsagePublic key certificate key usage (X.509 attribute)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.17 |
certificateExtKeyUsagePublic key certificate extended key usage (X.509 attribute)ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.18 |
certificateBasicConstraintsPublic key certificate basic constraintsro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.19 |
certificateCrlDistrPointsList of CRL distribution points URLs (CDPs), extracted from certificate extension. Supports only HTTP URLs, other protocols are ignored.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.20 |
certificateCaEntityIdentifier of an associated certificate authorityro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.21 |
certificateKeyEntityIdentifiers of cryptograhic keys associated with public key certificate.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.6.4.3.1.22 |
emailNotifySettings OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.7 |
emailNotifyConfigEmail functionality configuration.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.1 |
smtpServerNameName or IP Address (IPv4 or IPv6) of the SMTP server.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.7.2 |
smtpServerPortPort of the SMTP server.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.7.3 |
smtpServerConnectionSecuritySecurity type for the connection to the SMTP server.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.4 |
smtpServerAuthConfigConfiguration of authentication with SMTP server. If set from noAuth(1) to auth(2) then smtpServerAccount and smtpServerPasswd have to be given in the same SET request.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.5 |
smtpServerAccountAccount used for authentication with SMTP server.rw SnmpAdminString .1.3.6.1.4.1.2544.1.14.5.7.6 |
smtpServerPasswdPassword used for authentication with SMTP server. Read requests on this object will return a zero-length string.rw SnmpAdminString .1.3.6.1.4.1.2544.1.14.5.7.7 |
emailRecipientTableTable of email recipients. SEQUENCE OF EmailRecipientEntry .1.3.6.1.4.1.2544.1.14.5.7.8 |
emailRecipientEntry EmailRecipientEntry .1.3.6.1.4.1.2544.1.14.5.7.8.1 |
emailRecipientId Integer32 .1.3.6.1.4.1.2544.1.14.5.7.8.1.1 |
emailRecipientAddressAn email address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.7.8.1.2 |
emailRecipientTypeThe default value is to(1).rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.8.1.3 |
emailRecipientRowStatusThe status of this conceptual row. To create a row in this table, set this object to createAndGo(4). To remove a row, set this object to destroy(6).rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.7.8.1.4 |
emailRecipientFormatThe email format. You can choose either XML or the human readable email text format. The default value is xml(1)rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.8.1.5 |
emailRecipientMinSeverityThe minimum severity of alarms that are sent to the recipient. The default value is low(1)rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.8.1.6 |
emailRecipientAttachmentAttach trace in sor format. The default value is no(1)rw Enumeration .1.3.6.1.4.1.2544.1.14.5.7.8.1.7 |
externalIdTableTable defining the mapping of portIds to externalIds. SEQUENCE OF ExternalIdEntry .1.3.6.1.4.1.2544.1.14.5.7.9 |
externalIdEntry ExternalIdEntry .1.3.6.1.4.1.2544.1.14.5.7.9.1 |
externalIdThe externalId for the corresponding port.rw DisplayString .1.3.6.1.4.1.2544.1.14.5.7.9.1.1 |
smtpSenderAddressSender Address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.7.10 |
smtpExtendedHelloEHLO (Extended Hello) or HELO (Hello) identifies the server initiating the connection.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.7.11 |
advaSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.8 |
authTrapUserNameThe name string for user authentication purposes.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.8.1 |
authTrapLctIpIP address of LCT used in NE access.ro IpAddress .1.3.6.1.4.1.2544.1.14.5.8.2 |
authTrapStatusIndication whether security operation was successful/unsuccessful.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.8.3 |
authTrapSessionIdSession name used in NE access.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.8.4 |
authTrapProtocolProtocol type used in NE access.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.8.5 |
authTrapSuccessfulAuthCountNumber of successful authentications.ro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.8.6 |
authTrapUnsuccessfulAuthCountNumber of unsuccessful authentications.ro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.8.7 |
authTrapLogoutCountNumber of logouts.ro Unsigned32 .1.3.6.1.4.1.2544.1.14.5.8.8 |
authTrapLctIpv6IPv6 address of LCT used in NE access.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.8.9 |
lossGuidance OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.9 |
lossGuidanceConfigrw Enumeration .1.3.6.1.4.1.2544.1.14.5.9.1 |
minLossDefault value is 20. In tenth of dB.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.2 |
alwDevDefault value is 10. In tenth of dB.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.3 |
lossKmDefault value is 29. In hundredth of dB.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.4 |
lossConnectorsDefault value is 5. In tenth of dB.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.5 |
lossSplicesDefault value is 1. In tenth of dB.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.6 |
numConnectorsDefault value is 2.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.7 |
numSplicesDefault value is 2.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.9.8 |
userManagement OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.10 |
userManagementTableuserManagementTable SEQUENCE OF UserManagementEntry .1.3.6.1.4.1.2544.1.14.5.10.1 |
userManagementEntryEntry of userManagementTable UserManagementEntry .1.3.6.1.4.1.2544.1.14.5.10.1.1 |
userManagementRowStatusRowStatusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.10.1.1.1 |
userManagementUsernameThe name string for user authentication purposesrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.10.1.1.2 |
userManagementEmailAddressAn email addressrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.10.1.1.3 |
userManagementPrivilegeLevelrw Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.4 |
userManagementSecurityLevelrw Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.5 |
userManagementAuthPrivKeyA human readable string representing the current or new password for user account. Users with administrator privileges can use this object to set the password of other users.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.10.1.1.6 |
userManagementAuthPrivKeyOldA human readable string representing the old password for user account. This object should be used only for password change procedure.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.10.1.1.7 |
userManagementUdpSessionStatusUDP-based User Session Statusro Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.8 |
userManagementSso2faIf enabled, user can login only if Single Sign On and 2 Factor Authentication are enabled. This parameter can be set only on user creation.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.9 |
userManagementSnmpAuthProtocolChanges the HMAC for v3 Authentication. Default is MD5. This parameter can be set only on password creation/change.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.10 |
userManagementPrivacyKeyTypeDefines if SNMP Privacy Key should use a user password as value. Will delete userManagementPrivacyKey if set to authkey.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.10.1.1.11 |
userManagementPrivacyKeyPrivacy key/password for SNMP v3 auth-priv queries encryption.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.10.1.1.12 |
exportMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.11 |
exportMgmtRequestSet request to initiate software management related actionrw Enumeration .1.3.6.1.4.1.2544.1.14.5.11.1 |
exportMgmtStateThe current status of the export process. When failure is set then databaseMgmtLastError is applicable.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.11.2 |
exportMgmtLastErrorThe latest failure of the export process. Applicable only when exportMgmtLastError is set to 'failure'. NOTE: All failures that are caused by malfunctioning hardware are reported as internalError.ro Enumeration .1.3.6.1.4.1.2544.1.14.5.11.3 |
exportMgmtServerAddressThe IP address of the external FTP/SCP server.rw IpAddress .1.3.6.1.4.1.2544.1.14.5.11.4 |
exportMgmtServerLoginThe login name on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.11.5 |
exportMgmtServerPasswdThe password on the external FTP/SCP server. Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.11.6 |
exportMgmtServerDirectoryThe file location (path) on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.11.7 |
exportMgmtFileNameThe file name (without path and either without file name extension) on the external FTP/SCP server or the name of the file which has been downloaded to the NE.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.11.8 |
exportMgmtTransferProtocolThe transfer protocol to be used.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.11.9 |
exportMgmtFtpPortThe TCP port number of the FTP server used for file transfer. Default value is 21.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.11.10 |
exportMgmtActionProgressOperational progress in % i.e. file transferro Integer32 (0..100 | -2147483648) UNITS "%" .1.3.6.1.4.1.2544.1.14.5.11.11 |
exportMgmtIpv6AddressThe IPv6 address of the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.5.11.12 |
exportMgmtScpPortThe TCP port number of the SCP server used for file transfer. Default value is 22.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.11.13 |
bidirSettings OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.12 |
bidirSettingsTimeSlotConfigThis value selects the system-wide configuration about the number of time slots and the time slot used by this ALM unit. numSlots3unitSlot2 (32) means three time slots and the second one is used on this ALM unit.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.12.1 |
bidirSettingsInactiveUserCmdsIf this option is enabled it allows users to run tasks during the inactive time slot.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.12.2 |
dwdmExtraWaitTimeSlotAdd extra time before sending out the laser pulserw Integer32 .1.3.6.1.4.1.2544.1.14.5.12.3 |
remoteAuth OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.13 |
authmodedefines whether a remote authentication is enabled or not and if so which kind of serverrw Enumeration .1.3.6.1.4.1.2544.1.14.5.13.1 |
loginmodespecifies the authentication protocolrw Enumeration .1.3.6.1.4.1.2544.1.14.5.13.2 |
sso2faspecifies whether single sign on is possible during 2 factor authenticationrw Enumeration .1.3.6.1.4.1.2544.1.14.5.13.3 |
remoteAuthServersTableremoteAuthServersTable SEQUENCE OF RemoteAuthServersEntry .1.3.6.1.4.1.2544.1.14.5.13.4 |
remoteAuthServersEntryEntry of remoteAuthServersTable RemoteAuthServersEntry .1.3.6.1.4.1.2544.1.14.5.13.4.1 |
remoteAuthServersId Integer32 .1.3.6.1.4.1.2544.1.14.5.13.4.1.1 |
remoteAuthServersIpAddressIpAddresse v4/v6rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.13.4.1.2 |
remoteAuthServersPortThe default Radius 1812 /TACACS+ 49.rw Integer32 .1.3.6.1.4.1.2544.1.14.5.13.4.1.3 |
remoteAuthServersSecretsecret of the remoteAuthServerrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.5.13.4.1.4 |
remoteAuthServersTimeoutthe timeout in seconds (default 3)rw Integer32 (1..10 ) UNITS "s" .1.3.6.1.4.1.2544.1.14.5.13.4.1.5 |
remoteAuthServersActiverw Enumeration .1.3.6.1.4.1.2544.1.14.5.13.4.1.6 |
prioSettings OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.5.14 |
prioSettingsConfigThis value enables/disables the system-wide usage of Priority Ports.rw Enumeration .1.3.6.1.4.1.2544.1.14.5.14.1 |
maintain OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.6 |
maintainTableTable of maintenance actions of monitor ports. SEQUENCE OF MaintainEntry .1.3.6.1.4.1.2544.1.14.6.1 |
maintainEntry MaintainEntry .1.3.6.1.4.1.2544.1.14.6.1.1 |
maintainOperationRequestSet request to initiate OTDR measurement. It can be performed only if portAdminState is in Mgt state except of runOtdrMeasurement (3), runFaultAnalysis (4), runResetMeanValues (7) and runFiberIdentification (10) which can be performed also if portAdminState is in service.rw Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.1 |
maintainOperationRefractiveIndexRefractive index multiplied by 1000000. Parameter must be provided for Fingerprint generation or OTDR measurement.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.2 |
maintainOperationExternalOffsetExternal offset length in meters. Parameter must be provided for Fingerprint generation or OTDR measurement.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.3 |
maintainOperationCouplerLossCoupler loss in tenth of dB. Parameter must be provided for Fingerprint generation.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.4 |
maintainOperationOtdrLengthMeasurement length in meters. Parameter must be provided for OTDR measurement. On 16ALM the allowed range is 100..35000.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.5 |
maintainOperationOtdrPowerLevelPower level in 0.01dBm. Parameter must be provided for OTDR measurement. Not available on 16ALM-1650D.rw Integer32 (-2000..2000) UNITS "0.01 dBm" .1.3.6.1.4.1.2544.1.14.6.1.1.6 |
maintainOperationOtdrPulseWidthPulse width in ns. Parameter must be provided for OTDR measurement. On 16ALM the allowed range is 25..1000.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.7 |
maintainOperationOtdrAverageRateAverage rate (0=512,1=1024,2=2048,3=4096,4=8192,5=16384,6=32768,7=65536). Parameter must be provided for OTDR measurement. Not available on 16ALM-1650D.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.8 |
maintainOperationStateThe current status of a measurement. When failure is set then maintainOperationLastError is applicable.ro Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.9 |
maintainOperationLastErrorThe latest failure of the maintain operation action. Applicable only when maintainOperationState is set to 'failure'.ro Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.10 |
maintainOperationNumConnectorsDefault value is taken from system.lossGuidancerw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.11 |
maintainOperationNumSplicesDefault value is taken from system.lossGuidancerw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.12 |
maintainOperationMaxLaserPowerMaximal laser power used for Fingerprint generation or OTDR measurement in 0.01dBm. Parameter must be provided for Fingerprint generation or OTDR measurement. The value '-1' correspond to the maximal laser power. For GPON measurements only values between 4 to 15 dbm are allowed. Not available on 16ALM.rw Integer32 (-1..1500) UNITS "0.01 dBm" .1.3.6.1.4.1.2544.1.14.6.1.1.13 |
maintainOperationOtdrLinkLengthLength of the optical link in meters. Parameter must be provided for OTDR measurement (max. 200000 meters) and fingerprint without reflector (max. 300000 meters) and must be greater or equal than maintainOperationOtdrLength. Not available on 16ALM.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.14 |
maintainOperationOtdrMeasTimeMeasurement time in seconds. Parameter must be provided for OTDR measurement. Not available on 16ALM.rw Integer32 .1.3.6.1.4.1.2544.1.14.6.1.1.15 |
maintainOperationDwdmModeThis variable is set to 'enabled' to allow DWDM measurements else only standard non DWDM measurements can be done.rw Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.16 |
maintainOperationLossCalculationPointLoss between the origin of the optical link and the loss calculation point is used for the bidirectional measurements or other measurements without reflector. Set to 0 to enable maintainOperationExpectedLoss for FingerprintWithoutReflector mode.rw Integer32 (500..150000 | 0) UNITS "m" .1.3.6.1.4.1.2544.1.14.6.1.1.17 |
maintainOperationFastModeThis variable is set to 'enabled' to activate faster OTDR measurements with less accuracy.rw Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.18 |
maintainOperationMonitoringModeThis variables decides which measurements method will be used for monitoring. Also used the set the Tone Frequency used for runFiberIdentification.rw Enumeration .1.3.6.1.4.1.2544.1.14.6.1.1.19 |
maintainOperationExpectedLossExpected loss in tenth of dB. Between 5 and 35 db. Parameter maintainOperationLossCalculationPoint must be set to 0 for it to be used.rw Integer32 (50..350 | 0) .1.3.6.1.4.1.2544.1.14.6.1.1.20 |
scheduleFaTableTable of scheduled measurement actions of monitor ports. SEQUENCE OF ScheduleFaEntry .1.3.6.1.4.1.2544.1.14.6.2 |
scheduleFaEntry ScheduleFaEntry .1.3.6.1.4.1.2544.1.14.6.2.1 |
scheduleFaFirstRunDate (UTC) from where the schedule calculation should start.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.6.2.1.1 |
scheduleFaIntervalInterval between two measurements, will not run if disabled.rw Enumeration .1.3.6.1.4.1.2544.1.14.6.2.1.2 |
scheduleFaRequiredStateScheduled Fa Measurement, will only be done if in the right adminstate (default 1 inService)rw Enumeration .1.3.6.1.4.1.2544.1.14.6.2.1.3 |
scheduleFaNextRunNext date (UTC) where scheduled Fa will try to run.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.6.2.1.4 |
scheduleFaLastRunLast date (UTC) where scheduled Fa was executed.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.2544.1.14.6.2.1.5 |
scheduleFaStatusStatus of scheduled Fa Measurement, will rest to idle (1) only at full 1/4 hour intevallsro Enumeration .1.3.6.1.4.1.2544.1.14.6.2.1.6 |
otdrTraceMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.7 |
otdrTraceMgmtTableTable of trace management of monitor ports. SEQUENCE OF OtdrTraceMgmtEntry .1.3.6.1.4.1.2544.1.14.7.1 |
otdrTraceMgmtEntry OtdrTraceMgmtEntry .1.3.6.1.4.1.2544.1.14.7.1.1 |
otdrTraceMgmtRequestSet request to initiate trace management related actionrw Enumeration .1.3.6.1.4.1.2544.1.14.7.1.1.1 |
otdrTraceMgmtStateThe current status of the export/upload of OTDR traces. When failure is set then otdrTraceMgmtLastError is applicable.ro Enumeration .1.3.6.1.4.1.2544.1.14.7.1.1.2 |
otdrTraceMgmtLastErrorThe latest failure of the export/upload of OTDR traces process. Applicable only when otdrTraceMgmtState is set to 'failure'. NOTE: All failures that are caused by malfunctioning hardware are reported as internalError.ro Enumeration .1.3.6.1.4.1.2544.1.14.7.1.1.3 |
otdrTraceMgmtServerAddressThe IP address of the external FTP/SCP server.rw IpAddress .1.3.6.1.4.1.2544.1.14.7.1.1.4 |
otdrTraceMgmtServerLoginThe login name on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.7.1.1.5 |
otdrTraceMgmtServerPasswdThe password on the external FTP/SCP server. Read requests on this object will return a zero-length string.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.7.1.1.6 |
otdrTraceMgmtServerDirectoryThe OTDR trace destination location (path) on the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.7.1.1.7 |
otdrTraceMgmtFileNameTarget File Name of the trace without extension. Extension is either 'sor' or 'csv'. Depends on the selected OTDR Trace Management Requestrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.7.1.1.8 |
otdrTraceMgmtTransferProtocolThe transfer protocol to be used.rw Enumeration .1.3.6.1.4.1.2544.1.14.7.1.1.9 |
otdrTraceMgmtFtpPortThe TCP port number of the FTP server used for file transfer. Default value is 21.rw Integer32 .1.3.6.1.4.1.2544.1.14.7.1.1.10 |
otdrTraceMgmtActionProgressOperational progress in % i.e. file transferro Integer32 (0..100 | -2147483648) UNITS "%" .1.3.6.1.4.1.2544.1.14.7.1.1.11 |
otdrTraceMgmtAutoFaReferenceFault Analysis reference number. A value of 0 means the latest auto-generated fault analysis is exported.rw Integer32 .1.3.6.1.4.1.2544.1.14.7.1.1.12 |
otdrTraceMgmtIpv6AddressThe IPv6 address of the external FTP/SCP server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.7.1.1.13 |
otdrTraceMgmtScpPortThe TCP port number of the SCP server used for file transfer. Default value is 22.rw Integer32 .1.3.6.1.4.1.2544.1.14.7.1.1.14 |
inventory OBJECT IDENTIFIER .1.3.6.1.4.1.2544.1.14.8 |
inventoryTableInventory table SEQUENCE OF InventoryEntry .1.3.6.1.4.1.2544.1.14.8.1 |
inventoryEntry InventoryEntry .1.3.6.1.4.1.2544.1.14.8.1.1 |
inventoryShelfNoShelf number: 0 for the ALM itself, 1 .. 8 for Port Extenders Integer32 .1.3.6.1.4.1.2544.1.14.8.1.1.1 |
inventorySlotNoAdress index. Integer32 .1.3.6.1.4.1.2544.1.14.8.1.1.2 |
inventoryPortNoAdress index. Integer32 .1.3.6.1.4.1.2544.1.14.8.1.1.3 |
inventoryExtNoAdress index. Integer32 .1.3.6.1.4.1.2544.1.14.8.1.1.4 |
inventoryClassNameEntity Class Name. Integer32 .1.3.6.1.4.1.2544.1.14.8.1.1.5 |
inventoryAidStringAID: SHMON-1 or SHEXT-1 ... SHEXT-8ro IdentityTranslation (ADVA-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.6 |
inventoryUnitNameOfficial Equipment Namero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.7 |
inventoryFirmwarePackageRevFirmware Package Revision Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.8 |
inventoryHardwareRevEquipment Revision Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.9 |
inventoryFpgaRevThe active FPGA version on the Unitro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.10 |
inventorySerialNumberEquipment Serial Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.11 |
inventoryPartNumberPart Numberro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.12 |
inventoryCleiCodeCommon Language Equipment Identifierro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.13 |
inventoryOriginEither Vendor Code for the ALM itself or Country of Origin Code for Port Extendersro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.14 |
inventoryShelfTypeType of the physical entityro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.15 |
inventoryUniversalSerialIdentUnique Serial Identifierro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.2544.1.14.8.1.1.16 |