CISCO-XGCP-EXT-MIB
AI MIB Summary
The CISCO-XGCP-EXT-MIB module extends Cisco's xGCP framework to monitor and configure local media gateway call control parameters and provisioning profiles for circuit-based call establishment. It specifically exposes metrics for default call control settings and associated circuit-specific profiles used to manage voice traffic signaling and routing within Cisco gateways.
This MIB module is an extension to CISCO-XGCP-MIB.
It defines the parameters related to the following aspects in xGCP protocols:
* Default call control parameters in the local media
gateway.
* Provisioning specific call control profiles which can
be associated with the circuits for the call establishment in the circuits.
Main OID:
ciscoXgcpExtMIB.1.3.6.1.4.1.9.9.325
63
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
63 total| Object Name |
|---|
ciscoXgcpExtMIBThis MIB module is an extension to CISCO-XGCP-MIB.
It defines the parameters related to the following
aspects in xGCP protocols:
* Default call control parameters in the local media
gateway.
* Provisioning specific call control profiles which can
be associated with the circuits for the call
establishment in the circuits. MODULE-IDENTITY .1.3.6.1.4.1.9.9.325 |
cxgcpExtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.325.1 |
cxgcpExtConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.325.1.1 |
cxeCallCtrlConfigTableThis table contains objects used for configuring general
parameters in call control default to the local media gateway
in xGCP protocols. SEQUENCE OF CxeCallCtrlConfigEntry .1.3.6.1.4.1.9.9.325.1.1.1 |
cxeCallCtrlConfigEntryThere is one entry for each media gateway.
The entry will be automatically generated when a media
gateway is detected. CxeCallCtrlConfigEntry .1.3.6.1.4.1.9.9.325.1.1.1.1 |
cxeCallCtrlControlServiceTypeThis object identifies Type Of Service (TOS) field of
IP header for the control packet in VoIP application.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.1 |
cxeCallCtrlBearerServiceTypeThis object identifies Type Of Service (TOS) field
of IP header for the voice payload packet in VoIP
application.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.2 |
cxeCallCtrlVoIpDtmfRelayModeThis object defines whether the DTMF (Dual Tone,
Multi-Frequency) digits need to be transported to the other
endpoint via NSE packets in Voice Over IP.
The value of this object will be utilized when the call
agent does not specify this parameter.rw DtmfRelayMode .1.3.6.1.4.1.9.9.325.1.1.1.1.3 |
cxeCallCtrlVoIpDtmfCodecThis object identifies DTMF relay codec for VoIP.
This object is not applicable if cxeCallCtrlVoIpDtmfRelay
is DtmfRelayDisabled.rw DtmfCodecType .1.3.6.1.4.1.9.9.325.1.1.1.1.4 |
cxeCallCtrlVoAal2DtmfRelayModeThis object defines whether the DTMF (Dual Tone,
Multi-Frequency) digits need to be transported to the other
endpoint in Voice over AAL2 packets.
The value of this object will be utilized when the call
agent does not specify this parameter.rw DtmfRelayMode .1.3.6.1.4.1.9.9.325.1.1.1.1.5 |
cxeCallCtrlVoAal2DtmfCodecThis object identifies DTMF relay CODEC for Voice over AAL2.
This object is not applicable if cxeCallCtrlVoAal2DtmfRelay
is DtmfRelayDisabled.rw DtmfCodecType .1.3.6.1.4.1.9.9.325.1.1.1.1.6 |
cxeCallCtrlTsePayloadThis object identifies TSE (Telephony Signaling
Events) payload type.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.7 |
cxeCallCtrlNetNseTimerThis object identifies Network Signaling Event (NSE)
timeout value.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.8 |
cxeCallCtrlRtcpRcvTimerThis object identifies the number of times of Real Time
Control Transport (RTCP) report interval if the media
gateway has not recieved any RTCP packets from another
side.
The media gateway will mark another side inactive, or
delete it if no RTCP packet has been received for
the value of this object times the RTCP report interval.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.9 |
cxeCallCtrlIgnoreAal2LcoCodecThis object defines whether to ignore the AAL2 Local
Connection Option (LCO) message from the call agent
or not.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.1.1.10 |
cxeCallCtrlDigitMapOrderThis object defines the type of digit map order.
The MGC can advise and load the gateway with a digit map
that correspond to the dial plan to collect the access
codes, credit card numbers and other numbers requested
by call control services.rw Enumeration .1.3.6.1.4.1.9.9.325.1.1.1.1.11 |
cxeCallCtrlT38InhibitedThis object defines whether T.38 is inhibited in the
media gateway or not.
T.38 is a Fax Relay Protocol defined by ITU for
real-time protocol for Fax over IP networks.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.1.1.12 |
cxeCallCtrlT38NseRspTimerThis object defines a timeout value for a timer.
This timer is started after sending a NSE 200
while waiting for the NSE 201 acknowledgement or
NSE 202 negative acknowledgement. Expiration of the
timer will indicate that the request for switch
to T.38 has been rejected or discarded by the far end.
The initial value is 1000 ms and this value
can only be set in the increments of 250 ms.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.13 |
cxeCallCtrlT38FecEnabledThis object is used to enable the Forward Error
Correction (FEC) for UDP-based fax transport.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.1.1.14 |
cxeCallCtrlT38LsRedundancyThis object determines the extent of the Internet Fax
Protocol (IFP) packet transmission redundancy for
the low-speed control information exchanged during
the first phase of a T.38 fax relay connection.
Depending on whether Forward Error Correction (FEC)
is enabled (cxeCallCtrlT38FecEnabled is set to 'true')
or not, this object has different meanings.
If FEC is disabled, then this object is the maximum
number of prior IFP packets within a Unnumbered
Datagram Protocol Transport Layer (UDPTL) packet carrying
low speed information, not counting the primary or
current IFP packet.
If FEC is enabled, then this object is the maximum
number of FEC messages within a UDPTL packet carrying
low speed information.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.15 |
cxeCallCtrlT38HsRedundancyThis object determines the extent of the Internet Fax
Protocol (IFP) packet transmission redundancy for
the high-speed control and image information
exchanged following the initial low-speed phase of
a T.38 fax relay connection.
Depending on whether forward error correction (FEC)
is enabled (cxeCallCtrlT38FecEnabled is set to 'true')
or not. If FEC is disabled, then this object is the
maximum number of prior IFP packets within a UDPTL packet
carrying high speed information, not counting the
primary or current IFP packet.
If FEC is enabled, then this object is the maximum
number of FEC messages within a UDPTL packet carrying
high speed information.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.1.1.16 |
cxeCallCtrlT38NsfCountryCodeThis object specifies the country code for identifying
the country where the media gateway with non-standard
capabilities was manufactured.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw CountryCodeITU (CISCO-TC) .1.3.6.1.4.1.9.9.325.1.1.1.1.17 |
cxeCallCtrlT38NsfVendorCodePer its definition (ITU T.35), the Vendor Code (also
called the Terminal Provider Code) in the Non-Standard
Facilities (NSF) code is a two-byte field identifying the
manufacturer of the media gateway with non-standard
capabilities.
This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.rw CxeTerminalProviderCode .1.3.6.1.4.1.9.9.325.1.1.1.1.18 |
cxeCallCtrlVselDselFselSupportThis object is used to enable or disable VSEL, DSEL and
FSEL support.
VSEL: Voice codec, packet length and packet times Selection
DSEL: Data codec, packet length and packet times Selection
FSEL: Fax codec, packet length and packet times Selection
If cxeCallCtrlVselDselFselSupport is true, then the media
gateway must indicate prefered codec, packet length and
packet times for an ATM connection.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.1.1.19 |
cxeCallCtrlDefaultBearTrafficThis object specifies the combination of the network
type (IP/ATM), virtual circuit type (PVC/SVC) and
ATM adaptation layer type (AAL1/AAL2/AAL5) for the
connection used in transporting bearer traffic.
ipPvcAal5 (1) - The bearer traffic is transported in
IP network, through Permanent Virtual
Circuit(PVC) over AAL5 adaptation layer.
atmPvcAal2 (2) - The bearer traffic is transported in
ATM network, through Permanent Virtual
Circuit(PVC) over AAL2 adaptation layer.
atmSvcAal2 (3) - The bearer traffic is transported in
ATM network, through Switching Virtual
Circuit(SVC) over AAL2 adaptation layer.
atmSvcAal1 (4) - The bearer traffic is transported in
ATM network, through Switching Virtual
Circuit(SVC) over AAL1 adaptation layer.
If the call agent specifies the bear traffic type in the
MGCP (Media Gateway Control Protocol) local connection
options (CRCX request), then configuration of this object
will have no effect, else the value of this object will be
used when sending CRCX response.rw Enumeration .1.3.6.1.4.1.9.9.325.1.1.1.1.20 |
cxeCallCtrlLastFailedMgcAddrTypeThis object indicates the address type, either IPv4 or
IPv6, of cxeCallCtrlLastFailedMgcAddress.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.325.1.1.1.1.21 |
cxeCallCtrlLastFailedMgcAddressThis object indicates the address of MGC (Media Gateway
Controller) with which the media gateway had tried to
communicate lastly but failed.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.325.1.1.1.1.22 |
cxeCallCtrlProfileTableThis table defines the call control profiles.
A call control profile contains the call control information
that a call agent uses to establish a call. In the call
control profile, it has the following configurations:
(1) The information of call agent, such as its address,
connecting port, service type and version.
(2) The maximum retry parameters in the message exchange
between the call agent and the media gateway.
(3) The timeout settings in the call control.
A call control profile can be associated with a voice
interface (DS0 group in TDM side), so all the calls set up
in the voice interface will use the call control
parameters from the profile.
A call control profile can be associated with a Media Gateway
Controller(MGC)/call agent redundant group (cMgcGrpParamTable
defined in CISCO-MGC-MIB). In this case, the call agent
information for the profile will be determined by the MGC
redundant group. SEQUENCE OF CxeCallCtrlProfileEntry .1.3.6.1.4.1.9.9.325.1.1.2 |
cxeCallCtrlProfileEntryEach entry describes an instance of a call control
profile in the media gateway.
When an entry of call control profile is added to the table,
the following object must be provided:
cxeCcProfileName - an unique string of profile name to
identify the profile.
After the entry is added, all the accessible objects can be
modified except cxeCcProfileName. If users want to modify
the name of the call control profile, they have to delete
the original entry and create another entry with the new
name. CxeCallCtrlProfileEntry .1.3.6.1.4.1.9.9.325.1.1.2.1 |
cxeCcProfileIndexThis object uniquely identifies the call control profile. CCallControlProfileIndex (CISCO-MEDIA-GATEWAY-MIB) .1.3.6.1.4.1.9.9.325.1.1.2.1.1 |
cxeCcProfileNameA unique name for the profile. The name of the profile
has to be unique among all entries of the table.
This object is mandatory during the creation of the entry.
This object can not be modified.
If users want to modify the name of the call control profile,
they have to delete the original entry and create another
entry with the designated name.rw DisplayString .1.3.6.1.4.1.9.9.325.1.1.2.1.2 |
cxeCcProfileNumVifsThis object reprsents the total number of voice interface
(DS0 group) associated with this call control profile.
The value of '0' means there is no voice interfaces
associated with the profile.
Before the call control profile can be deleted,
this object should have the value of 0
(means all voice interfaces should be de-associated with
the profile before the profile can be deleted).ro Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.3 |
cxeCcProfileMgcGrpNumThis object indicates which MGC Redundant group number
that the call control profile will be used.
The value is the index to MGC Redundant Group Table
(cMgcGrpParamTable).
There are two conditions for associating a MGC group
with a profile:
1. At least one MGC is associated with the MGC group
2. At least one protocol is associated with the MGC group
After a MGC Redundant Group is associated with the
profile (cxeCcProfileMgcGrpNum > 0):
In the call setup, the parameters of MGCs
within the MGC Redundant Group will be sequentially
tried according to its preference.
The value of '0' means there is no MGC Redundant
Group associated with the profile.
This object takes the precedence of object
cxeCcProfileMgcAddress of the profile.
If users try to set a value to cxeCcProfileMgcAddress
while the value of this object is non-zero, the set will
be rejected.
Before the call control profile can be deleted,
this object should have the value of 0.
Which means MGC Redundant Group should be
de-associated with the profile before the profile
can be deleted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.4 |
cxeCcProfileMgcAddrTypeThis object identifies the address type applicable to
cxeCcProfileMgcAddress.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.325.1.1.2.1.5 |
cxeCcProfileMgcAddressThis object specifies the address of Media Gateway
Controller (MGC) configured in the profile.
When cxeCcProfileMgcGrpNum is non-zero (which menas
using MGC group), this object can not be set.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.325.1.1.2.1.6 |
cxeCcProfileProtocolIdxThis object specifies the protocol that the media gateway
should communicate with MGC during call setup.
It is the index of the protocol table(cMediaGwProtocolTable).
If cxeCcProfileMgcGrpNum is non-zero, the value of this object
will be ignored. The protocol will be determined by the
MGC group.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.7 |
cxeCcProfileXgcpRetryMethodThis object specifies the command/response retry method
when the media gateway communicates with the MGC in
xGCP protocols.rw CXgcpRetryMethod (CISCO-XGCP-MIB) .1.3.6.1.4.1.9.9.325.1.1.2.1.8 |
cxeCcProfileRetryMax1This object contains the suspicious error threshold for
signaling messages.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.9 |
cxeCcProfileDnsLookupMax1This object enables/disables the Max1 Domain Name Server
(DNS) query operation when Max1 expires.
This object is used when a gateway-initiated message is not
acknowledged by the MGC. If the object is 'true', a DNS
query is performed to re-resolve MGC's domain name after
exhausting Max1 retries on any IP address associated with
the MGC.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.2.1.10 |
cxeCcProfileRetryMax2This object contains the disconnect error threshold
for signaling messages.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.11 |
cxeCcProfileDnsLookupMax2This object enables/disables the Max2 Domain Name Server
(DNS) query operation when Max2 expires.
This object is used when a gateway-initiated message is not
acknowledged by the MGC. If the object is 'true', a DNS
query is performed to re-resolve MGC's domain name after
exhausting Max2 retries on the last IP address associated
with the MGC.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.2.1.12 |
cxeCcProfileMwiTimeoutThe timeout value for the message waiting indicator tone.
Message Waiting Indicator (MWI) tone is used with message
waiting services, it indicates that the media gateway
is ready to accept address information or other information
from an access line.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.13 |
cxeCcProfileTsmaxTimeoutThe timeout value for retransmission removal.
The gateway uses the value of this object to determine how
long for the MGCP messages stored in the retransmission
queue before they are discarded.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.14 |
cxeCcProfileTdinitTimeoutThe voice interface (DS0 group) becomes disconnected when
the media gateway tries to communicate with the call agent
and the retransmission procedure times out after retrying.
The voice interface (DS0 group) in disconnected state
starts the disconnected timer initialised to the random
value and uniformly distributed between 1 and initial
waiting delay (Tdinit) in seconds.
The gateway waits for either the expiration of the timer,
or the reception of call agent command or the detection of
local user activity for the voice interface (DS0 group).
When the disconnected timer elapses, or when a command is
received from the call agent or when there is a local user
activity, the media gateway sends the Restart In Progress
command with the restart method as RM:disconnected to the
call agent.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.15 |
cxeCcProfileTdminTimeoutThe DS0 group (voice interface) becomes disconnected
when it tries to communicate with the call agent and the
retransmission procedure times out after retrying.
The DS0 group (voice interface ) in disconnected state
starts the disconnected timer initialised to the random
value and uniformly distributed between 1 and initial
waiting delay (Tdinit) in seconds.
The gateway waits for either the end of this timer, or the
reception of call agent command or the detection of local
user activity for the DS0 group(voice interface).
When the disconnected timer elapses, or when a command is
received from the call agent or when there is a local user
activity, the Voice Gateway sends the Restart In Progress
command with the restart method as RM:disconnected to the
call agent.
In case of local user activity, a provisionable disconnected
minimum waiting delay (Tdmin) must have been elapsed
since the gateway became disconnected.
The minimum waiting delay (Tdmin) timeout value used by the
voice Gateway to send the Restart In Progress with the restart
method as RM:disconnected to the call agent if there is
any local user activity is defined by this object.
Media gateway initiated delete connection (DLCX) or restart
in progress (RSIP) commands are not considered as local user
activity.
The events observed on the TDM interface or on the network
constitute the local user activity.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.17 |
cxeCcProfileTdmaxTimeoutThe maximum waiting delay (Tdmax) timeout value used by the
media gateway to send the Restart In Progress with the
restart method as RM:disconnected to the call agent when
the voice interface associated ds0-group disconnection
condition occurs.
The DS0 group (voice interface) becomes disconnected when
it tries to communicate with the call agent and the
retransmission procedure times out after retrying.
The DS0 group (voice interface) in disconnected state
starts the disconnected timer initialised to the random
value and uniformly distributed between 1 and initial
waiting delay (Tdinit) in seconds.
The gateway waits for either the expiration of the timer,
or the reception of call agent command or the detection
of local user activity for the DS0 group (voice interface).
When the disconnected timer elapses, or when a command is
received from the call agent or when there is a local user
activity, the media gateway sends the Restart In Progress
command with the restart method as RM:disconnected to the
call agent.
If the disconnected procedure still left the DS0 group
(voice interface) disconnected, the disconnected timer
is doubled subject to a provisionable disconnected
maximum waiting delay (Tdmax) in seconds and the gateway
starts the new disconnected procedure again.
Once the maximum value is reached, the subsequent
disconnected Restart In Progress commands use the maximum
waiting delay (Tdmax).rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.18 |
cxeCcProfileTcritTimeoutThis object represents the timeout value for the critical
timer.
If used along with a digit map, the timer is started when
the last digit is received. i.e and when no more digits
are required for a digit map match. After this timer
expires, the digit map match is assumed to be complete.
If used without a digit map, the timer is started
immediately and cancelled (but not restarted) as soon
as a digit is entered.
This object is used by call processing when it processes
mid-call DTMF digit reporting.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.19 |
cxeCcProfileTparTimeoutThis object represents the partial dial timeout
and is used along with a digit map as the inter-digit
timer.
This object is used by call processing when it processes
mid-call DTMF digit reporting.
The timer is not started until the first digit is entered,
and the timer is restarted after each new digit is entered
untill either a digit map match or mismatch occurs.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.20 |
cxeCcProfileThistTimeoutThe MGCP protocol is organized as set of transactions, each
of which is composed of a command and a resonse. The MGCP
messages, being carried over UDP, may be subject to losses.
In the absence of a timely response, commands are repeated.
The media gateway must keep in memory a list of the responses
that it sent to recent transactions, and a list of the
transactions that are currently being executed.
Recent is here defined by the value of cxeCcProfileThistTimeout
that specifies the number of seconds that responses to
old transactions must be kept for.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.21 |
cxeCcProfileRtTimeoutThis object specifies time for which the local ring back
tone (towards the TDM) will be generated unless
interrupted (e.g., by the answer from the called party
or a delete connection command from the Call Agent).
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.22 |
cxeCcProfileRbkTimeoutThis object specifies time for which the remote ring
back tone (towards the packet network) will be
generated unless interrupted (e.g., by the answer
from the called party or a delete connection command
from the Call Agent).
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.23 |
cxeCcProfileCgTimeoutThis object specifies time for network congestion
tone will be generated.
The network congestion tone will be generated when
the network resources or bandwidth exceed their
threholds.
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.24 |
cxeCcProfileBzTimeoutThis object specifies time for which the busy tone
will be generated unless interrupted (e.g., by the
hangup from the calling party).
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.25 |
cxeCcProfileDlTimeoutThis object specifies time for which the dial tone
will be generated unless interrupted (e.g., by the
first DTMF digit from the calling party).
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.26 |
cxeCcProfileSlTimeoutThis object specifies time for which the stutter
dial tone or confirmation dial tone will be
generated unless interrupted (e.g., by the first
DTMF digit from the calling party).
The value of '0' indicates that the tone will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.27 |
cxeCcProfileRgTimeoutThis object specifies time for which the ringing
cadence will be generated towards the basic PBX
unless interrupted (e.g., by the answer from the
called party or a delete connection command from
the Call Agent).
This is also the time for which remote inband ring back
tone will be played towards the packet network.
The value of '0' indicates that the cadence will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.28 |
cxeCcProfileRoTimeoutThis object specifies time for which the reorder
tone or fast busy tone will be generated unless
interrupted (e.g., by the hangup from the called party).
The value of '0' indicates that the cadence will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.29 |
cxeCcProfileCot1TimeoutThis object specifies time for which the continuity
test tone 1 will be generated unless interrupted.
The value of '0' indicates that the cadence will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.30 |
cxeCcProfileCot2TimeoutThis object specifies time for which the continuity
test tone 2 will be generated unless interrupted.
The value of '0' indicates that the cadence will be
generated indefinitely unless interrupted.rw Integer32 .1.3.6.1.4.1.9.9.325.1.1.2.1.31 |
cxeCcProfileRowStatusThis object is used by users for adding/deleting an
entry from the table.
The entry can't be deleted if the value of
cxeCcProfileNumVifs is greater than zero or
the value of cxeCcProfileMgcGrpNum is greater than zero.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.325.1.1.2.1.32 |
cxeCallCtrlMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.325.2 |
cxeCallCtrlMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.325.2.1 |
cxeCallCtrlMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.325.2.2 |