CISCO-WIRELESS-P2MP-PHY-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CISCO-WIRELESS-P2MP-PHY-MIB.
114
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
114 total| Object Name |
|---|
ciscoWirelessPhyMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170 |
SNMPv2-SMI-v1 Unknown .1.3.6.1.4.1.9.9.170 |
p2mpRadioObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1 |
p2mpRadioBaseObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.1 |
p2mpPhyConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.1.1 |
p2mpRadioPhyTableThis table provides facilities to configure the physical
layer characteristics of the radio link.
The objects in this table are supported on the head end and
at the subscriber unit. SEQUENCE OF P2mpRadioPhyEntry .1.3.6.1.4.1.9.9.170.1.1.1.1 |
p2mpRadioPhyEntryThe entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface. The entry
is removed when the associated propDocsWirelessMaclayer
interface is deleted from the ifTable. P2mpRadioPhyEntry .1.3.6.1.4.1.9.9.170.1.1.1.1.1 |
p2mpSelfTestThis object is used to enable/disable self test. When set to
true(1), the software tests the memory and hardware integrity
shortly after the router powers up.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.1.1.1.1 |
p2mpDiversityAntennaPresentWhen true(1), this object indicates that a diversity
antenna is being used to receive the wireless transmissions.
When false(2), the radio system is using a single antenna
to transmit and receive.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.1.1.1.2 |
p2mpCableLossThis object indicates the measured signal power loss in dB
due to the cable connecting the radio to the main antenna.
The hardware compensates for this cable loss by adjusting the
receive and transmit gain appropriately. A value of 0
indicates no degradation in the signal due to the cable. The
radio hardware can compensate for a cable loss of no more
than 15 db.
This cable loss applies to the main antenna only.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.3 |
p2mpCableLossDiversityThis object indicates the measured signal power loss in dB
due to the cable connecting the radio to the diversity
antenna. The hardware compensates for this loss by adjusting
the receive and transmit gain appropriately. A value of 0
indicates no degradation in the signal due to the cable. The
radio hardware can compensate for a cable loss of no more
than 15 dB.
This cable loss applies to the diversity antenna only.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.4 |
p2mpDenyServiceIndicates if the service is disabled in the unit.
For Head-end unit, if this object has the value of
'true', the link is in loopback mode; otherwise the
link is enabled for transmitting / receiving data.
For Subscriber unit, if this object has the value of
'true', the subscriber unit service is disabled;
otherwise, the subscriber unit is enabled for
transmitting / receiving dataro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.1.1.1.5 |
p2mpClockRefExtThis object controls the use of external reference
clock for IF module as follows:
'true(1)' - an external reference clock is used
'false(2)' - an internal reference clock is used.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.1.1.1.6 |
p2mpCommonTrapEnableWhen set to true(1), the notifications common to the head end
and subscriber unit are enabled. When set to false(2), these
notifications are disabled.
The notification controlled by this object are:
- p2mpRadioPhyFailNotification
- p2mpTrapRfSupplyVoltage
- p2mpTrapRfRxOsc
- p2mpTrapRfTxOsc
- p2mpTrapRfTemp
- p2mpTrapRfCommLinkError
- p2mpTrapTxPower
- p2mpTrapRfStatusChangerw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.1.1.1.7 |
p2mpLastPhyFailureTypeThis object indicates the last physical link failure that
resulted in a p2mpRadioPhyFailNotification trap.
none(1) - no failure
p2mpHwConfigUnsupported(2) - The radio subsystem has
detected that the configuration requested is not
supported by the hardware. The p2mpLastPhyFailureReason
variable will indicate which configuration parameter is
not supported.
p2mpHwConfigMismatch(3) - The radio subsystem has detected
that the combination of the configuration parameters
requested is inconsistent and cannot be supported.
The p2mpLastPhyFailReason variable will indicate the
configuration parameter that causes the mismatch.
p2mpHwInitFailure(4) - The radio subsystem has failed to
initialize the hardware. This implies that there is a
critical error condition in the associated hardware.
The p2mpLastPhyFailReason specifies the reason why the
init failed.
p2mpHostIfCommLinkError(5) - The host could not communicate
with the IF module.
p2mpAutoCableCompFailure(6) - Failed to achieve automatic
cable compensation due to loss of Tx signal.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.1.1.1.8 |
p2mpLastPhyFailureReasonThis is a text string that describes the last physical link
failure identified by p2mpLastPhyFailureType.ro DisplayString .1.3.6.1.4.1.9.9.170.1.1.1.1.1.9 |
p2mpFreqResourceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.1.2 |
p2mpRfTableThis table contains information about the state of the radio
frequency resources used by the radio system.
Physically each RF resource may be realized by one antenna and
its associated control hardware. A single antenna and its
associated electronics may act as more than 1 RF resource. When
an RF resource acts as both a transmit and receive resource,
the transmit and receive frequency ranges may overlap. SEQUENCE OF P2mpRfEntry .1.3.6.1.4.1.9.9.170.1.1.2.1 |
p2mpRfEntryThis represents one entry in the p2mpRfTable.
An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless system. P2mpRfEntry .1.3.6.1.4.1.9.9.170.1.1.2.1.1 |
p2mpRfIndexThis object, along with the ifIndex of the MAC layer,
represents the index of this entry in the p2mpRfTable.
Each entry in the table provides details on the state of
the RF resources available in the system. Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.1 |
p2mpRfTypeThis object identifies the RF resource.ro CwrRfType -- Rsyntax INTEGER { -- main(0), -- diversity(1) -- } .1.3.6.1.4.1.9.9.170.1.1.2.1.1.2 |
p2mpRfOpModeThis object specifies whether this RF resource can either
transmit, receive, or do both.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.2.1.1.3 |
p2mpTxFreqRangeMinThis object represents the minimum frequency at which this RF
resource can transmit.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.4 |
p2mpTxFreqRangeMaxThis object represents the maximum frequency at which this RF
resource can transmit.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.5 |
p2mpRxFreqRangeMinThis object represents the lowest transmission frequency this
RF resource can receive.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.6 |
p2mpRxFreqRangeMaxThis object represents the highest transmission frequency that
this RF resource can receive.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.7 |
p2mpMinTxPowerThis object represents the minimum power that the RF subsystem
can supply the antenna.ro Integer32(-80..50) -- Units -- dBm .1.3.6.1.4.1.9.9.170.1.1.2.1.1.8 |
p2mpMaxTxPowerThis object represents the maximum power that the RF subsystem
can supply the antenna.ro Integer32(-80..50) -- Units -- dBm .1.3.6.1.4.1.9.9.170.1.1.2.1.1.9 |
p2mpRfTemperatureThis object represents the current temperature of the RF unitro Integer32(-40..100) -- Units -- Degrees Centigrade .1.3.6.1.4.1.9.9.170.1.1.2.1.1.10 |
p2mpRfTxOscStateThis object represents the state of the transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.ro CwrOscState -- Rsyntax INTEGER { -- oscillatorOk(1), -- osccillatorBad(2) -- } .1.3.6.1.4.1.9.9.170.1.1.2.1.1.11 |
p2mpRfRxOscStateThis object represents the state of the receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.ro CwrOscState -- Rsyntax INTEGER { -- oscillatorOk(1), -- osccillatorBad(2) -- } .1.3.6.1.4.1.9.9.170.1.1.2.1.1.12 |
p2mpRfSupplyVoltageStateThis object specifies whether the voltage supply to the RF
unit is within specifications or not. Voltage specifications
are hardware dependent.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.2.1.1.13 |
p2mpRfStatusThis object specifies whether the RF resource is functioning
properly. If it is functioning properly then it will be
online(1), else offline(2).
At the Subscriber Unit, this object will reflect offline(2)
if p2mpTxMuteEnable in the p2mpSuRadioPhyTable is true(1).ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.2.1.1.14 |
p2mpRfLoopbackSupportedThis object indicates if the RF unit supports loopback.
When true(1), the user can configure loopback using the
objects in p2mpLoopbackTable. When false(2), any attempt
to configure RF loopback will fail.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.1.2.1.1.15 |
p2mpDuplexerTableThis table contains information about the Duplexers
available for use on the system.
A Duplexer is a mechanical device, that acts as a band
pass filter when installed in an RF resource.
Normally a RF resource is capable of operating over a wide
frequency range. To operate at restricted frequencies, the user
has to own that part of the frequency spectrum. Since the user
may not own parts of the frequency spectrum over which the RF
resource may operate, a duplexer is installed at the RF.
This restricts the RF resource to operate in the passband
defined by the duplexer. SEQUENCE OF P2mpDuplexerEntry .1.3.6.1.4.1.9.9.170.1.1.2.2 |
p2mpDuplexerEntryThis represents one entry in the p2mpDuplexerTable.
Each entry contains information about the duplexers
capabilities and the associated RF resource.
An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless system. P2mpDuplexerEntry .1.3.6.1.4.1.9.9.170.1.1.2.2.1 |
p2mpDuplexerIndexThis object, along with ifIndex, uniquely identifies
an entry in this table. Each entry contains
information about the duplexer's capabilities and also
identifies the associated RF resource. Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.1 |
p2mpDuplexerRFThis object identifies the RF resource associated with this
duplexer.ro CwrRfType -- Rsyntax INTEGER { -- main(0), -- diversity(1) -- } .1.3.6.1.4.1.9.9.170.1.1.2.2.1.2 |
p2mpDuplexerLoPassbandMinFreqThis object identifies the minimum frequency in the low
passband that this duplexer will pass through without
attenuation.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.3 |
p2mpDuplexerLoPassbandMaxFreqThis object identifies the maximum frequency in the low
passband that this duplexer will pass through without
attenuation.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.4 |
p2mpDuplexerHiPassbandMinFreqThis object identifies the minimum frequency in the high
passband that this duplexer will pass through without
attenuation.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.5 |
p2mpDuplexerHiPassbandMaxFreqThis object identifies the maximum frequency in the high
passband that this duplexer will pass through without
attenuation.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.6 |
p2mpDuplexerReceivePassbandThis object indicates which of the two passbands are being used
to receive transmissions. The RF Resource can receive on
either of the duplexer passbands.
loPassband(1) - The RF Resource is receiving on a frequency
in the low passband.
hiPassband(2) - The RF Resource is receiving on a frequency
in the high passband.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.2.2.1.7 |
p2mpDuplexerTxInsertionLossThis object represents the loss in 'dB' that would result in
the transmission path due to the duplexer.ro Integer32 -- Units -- dB .1.3.6.1.4.1.9.9.170.1.1.2.2.1.8 |
p2mpDuplexerBurnDateThis object indicates the date when the revision information
was programmed into non-volatile memory.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.170.1.1.2.2.1.9 |
p2mpAntennaTableThis table contains information about the antennas available
in the system. SEQUENCE OF P2mpAntennaEntry .1.3.6.1.4.1.9.9.170.1.1.2.3 |
p2mpAntennaEntryAn entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless system. P2mpAntennaEntry .1.3.6.1.4.1.9.9.170.1.1.2.3.1 |
p2mpAntennaIndexThis object, along with ifIndex, represents the index of this
entry in the p2mpAntennaTable. Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.1 |
p2mpRfResourceThis object identifies if the antenna is connected to the main
or the diversity RF resource.ro CwrRfType -- Rsyntax INTEGER { -- main(0), -- diversity(1) -- } .1.3.6.1.4.1.9.9.170.1.1.2.3.1.2 |
p2mpAntennaXDimThis object represents the dimension of the antenna in the
X direction.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.3 |
p2mpAntennaYDimThis object represents the dimension of the antenna in the
Y direction.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.4 |
p2mpAntennaTypeThis object represents the antenna type. For example,
'dish-antenna'.rw DisplayString .1.3.6.1.4.1.9.9.170.1.1.2.3.1.5 |
p2mpAntennaDescrThis object is used to describe the antenna. For example,
it could be used to identify the manufacturer like in
'Manufactured by Watkins Johnson'.rw DisplayString .1.3.6.1.4.1.9.9.170.1.1.2.3.1.6 |
p2mpAntennaGainThis object represents the receive and transmit gain
of this antenna.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.7 |
p2mpAntennaPolarizationThis object represents the polarization of the antanna.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.2.3.1.8 |
p2mpRadioTestGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.1.3 |
p2mpLoopbackTableThis table provides facilities to establish loopback points to
exercise various sections of the hardware. SEQUENCE OF P2mpLoopbackEntry .1.3.6.1.4.1.9.9.170.1.1.3.1 |
p2mpLoopbackEntryThis represents one entry in the p2mpLoopbackTable. It
is created when the managed system detects a
propDocsWirelessMaclayer interface. The entry is removed
when the associated propDocsWirelessMaclayer interface
is deleted from the ifTable. P2mpLoopbackEntry .1.3.6.1.4.1.9.9.170.1.1.3.1.1 |
p2mpLocalLoopbackModeThis object is used to configure the system in loopback mode
prior to executing some system diagnostic tests. The user
selects the point in the system where the data signal should be
looped back. The diagnostic tests outlined in the user manual
have to be manually executed to determine success or failure.
Once all the tests are completed, normal operation is restored
by setting this object to noLoopback(1).
noLoopback(1) - no loopback
fir(2) - loopback at the Finite Impulse
Response (FIR) module.
if(3) - loopback at the IF module. This
exercises the FIR, and IF modules.
rf(4) - loopback at the RF unit. This
exercises the FIR, IF, and RF modules.
This mode is supported only when
p2mpRfLoopbackSupported is true(1).rw Enumeration .1.3.6.1.4.1.9.9.170.1.1.3.1.1.1 |
p2mpLocalLoopbackAntennaThis object identifies the RF resource used for
loopback testing. This object is not applicable for
loopback testing when p2mpLocalLoopbackMode has a
value of 'noLoopback(1)'.rw CwrRfType -- Rsyntax INTEGER { -- main(0), -- diversity(1) -- } .1.3.6.1.4.1.9.9.170.1.1.3.1.1.2 |
p2mpLocalLoopbackChannelThis object identifies the channel being used to
loopback the data. This object is not applicable
for loopback testing when p2mpLocalLoopbackMode has
a value of 'noLoopback(1)'.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.1.3.1.1.3 |
p2mpLedGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.1.4 |
p2mpLedTableEntity (Light emitting diode) LED information. For each LED on
the entity, an entry will exist in this table, describing the
location and current status of that LED. SEQUENCE OF P2mpLedEntry .1.3.6.1.4.1.9.9.170.1.1.4.1 |
p2mpLedEntryAn entry in the table, containing the LED information.
The entPhysicalIndex identifies the entity on which the LED's
are present. P2mpLedEntry .1.3.6.1.4.1.9.9.170.1.1.4.1.1 |
p2mpLedIndexFor a given entPhysicalIndex, this index value uniquely
identifies an entry in the p2mpLedTable. Integer32 .1.3.6.1.4.1.9.9.170.1.1.4.1.1.1 |
p2mpLedTypeIndicates the type or label of the LED.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.4.1.1.2 |
p2mpLedStateIndicates the state of the LED.ro Enumeration .1.3.6.1.4.1.9.9.170.1.1.4.1.1.3 |
p2mpRadioSuObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.2 |
p2mpSuRadioPhyTableThis table contains information about the currently configured
physical layer interfaces in the subscriber unit. SEQUENCE OF P2mpSuRadioPhyEntry .1.3.6.1.4.1.9.9.170.1.2.1 |
p2mpSuRadioPhyEntryAn entry containing the radio configuration information
of the propDocsWirelessMaclayer interface in the
subscriber unit.
The entry is created when a propDocsWirelessMaclayer
interface is detected in the subscriber unit. The entry
is deleted when the associated propDocsWirelessMaclayer
interface is removed. P2mpSuRadioPhyEntry .1.3.6.1.4.1.9.9.170.1.2.1.1 |
p2mpSuTxMuteEnableWhen true(1), this object indicates the subscriber unit
transmission has been turned off for a duration indicated by
p2mpSuTxMuteDuration. When false(2), this object indicates
that the subscriber unit is transmitting.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.2.1.1.1 |
p2mpSuTxMuteDurationThis object indicates the duration of time (in minutes)
for which the subscriber transmission will be turned off.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.2.1.1.2 |
p2mpSuPowerScanTableThis table contains information about the receive power
measured at the different possible center frequencies. SEQUENCE OF P2mpSuPowerScanEntry .1.3.6.1.4.1.9.9.170.1.2.2 |
p2mpSuPowerScanEntryAn entry containing the power related status
information of the propDocsWirelessMaclayer
interface in the subscriber unit.
The entry is created when a propDocsWirelessMaclayer
interface is detected in the subscriber unit. The entry
is deleted after the associated propDocsWirelessMaylayer
interface is removed. P2mpSuPowerScanEntry .1.3.6.1.4.1.9.9.170.1.2.2.1 |
p2mpSuPowerScanIndexFor a given ifIndex, this index value uniquely
identifies an entry in the p2mpSuPowerScanTable. Integer32 .1.3.6.1.4.1.9.9.170.1.2.2.1.1 |
p2mpSuCenterFrequencyThis object indicates the frequency at which the receive power
at the subscriber unit was measured.ro CwrRfFreqRange -- Rsyntax Integer32 .1.3.6.1.4.1.9.9.170.1.2.2.1.2 |
p2mpSuMeasuredPowerThis object represents the power measured at the frequency
indicated by p2mpSuCenterFrequency.ro Integer32(-127..50) -- Units -- dBm .1.3.6.1.4.1.9.9.170.1.2.2.1.3 |
p2mpRadioHeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.3 |
p2mpHeAlcTableThis table contains Automatic Line Control (ALC) configuration
information. It is supported at the head end only. SEQUENCE OF P2mpHeAlcEntry .1.3.6.1.4.1.9.9.170.1.3.1 |
p2mpHeAlcEntryAn entry containing the ALC configuration information
the propDocsWirelessMaylayer interface at the head end.
The entry is created when a propDocsWirelessMaclayer
interface is detected in the head end unit. The entry is
deleted after the associated propDocsWirelessMaclayer
interface is removed. P2mpHeAlcEntry .1.3.6.1.4.1.9.9.170.1.3.1.1 |
p2mpHeAlcEnableThis object is used to enable/disable ALC at the Head End. A
value of true(1), indicates that ALC is enabled.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.3.1.1.1 |
p2mpHeAlcIntervalThis object represents the scheduling interval. It is the
regular interval at which the ALC grant in Map is transmitted
to the SU'srw Unsigned32 .1.3.6.1.4.1.9.9.170.1.3.1.1.2 |
p2mpHeAlcNumMiniSlotsThis indicates the number of minislots within each grant.rw Unsigned32 .1.3.6.1.4.1.9.9.170.1.3.1.1.3 |
p2mpHeIntFreqTableThis table contains information about the state of the
intermediate frequency subsystem in the radio system. This
table is supported at the head end only. SEQUENCE OF P2mpHeIntFreqEntry .1.3.6.1.4.1.9.9.170.1.3.2 |
p2mpHeIntFreqEntryThe entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface in the head
end unit.
The entry is deleted when the associated
propDocsWirelessMaclayer interface is removed. P2mpHeIntFreqEntry .1.3.6.1.4.1.9.9.170.1.3.2.1 |
p2mpHeIfTxOscStateThis object indicates the state of the IF transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.ro CwrOscState -- Rsyntax INTEGER { -- oscillatorOk(1), -- osccillatorBad(2) -- } .1.3.6.1.4.1.9.9.170.1.3.2.1.1 |
p2mpHeIfRxOscStateThis object indicates the state of the IF receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.ro CwrOscState -- Rsyntax INTEGER { -- oscillatorOk(1), -- osccillatorBad(2) -- } .1.3.6.1.4.1.9.9.170.1.3.2.1.2 |
p2mpHeIfRefOscStateThis object indicates the state of the IF reference oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.ro CwrOscState -- Rsyntax INTEGER { -- oscillatorOk(1), -- osccillatorBad(2) -- } .1.3.6.1.4.1.9.9.170.1.3.2.1.3 |
p2mpHeIfInpFreqThis object represents the IF input frequency.ro Unsigned32 .1.3.6.1.4.1.9.9.170.1.3.2.1.4 |
p2mpHeIfOutFreqThis object represents the IF output frequency.ro Unsigned32 .1.3.6.1.4.1.9.9.170.1.3.2.1.5 |
p2mpHeTrapEnableWhen set to true(1), this enables the notifications
that are specific to the head end. When set to false(2),
these notifications are disabled.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.170.1.3.2.1.6 |
p2mpRadioPhyConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4 |
p2mpRadioPhyCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.1 |
p2mpRadioPhyCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.1.1 |
p2mpRadioPhyGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2 |
p2mpCommonRadioGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.1 |
p2mpCommonRfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.2 |
p2mpCommonTestGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.3 |
p2mpRadioSuGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.5 |
p2mpRadioHeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.6 |
p2mpRadioAntennaGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.1.4.2.8 |
p2mpPhyMIBNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.2 |
p2mpPhyMIBNotification OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.170.2.0 |
p2mpRadioPhyFailNotificationA p2mpRadioPhyFailNotification is sent if the value of
p2mpLastPhyFailureType changes due to the new failure
being detected in the Radio interface. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.1 |
p2mpTrapRfSupplyVoltageThe supply voltage to the RF resource has changed.
The p2mpRfSupplyVoltageState specifies whether the supply
voltage is in spec or not. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.2 |
p2mpTrapRfRxOscThe RF receive frequency oscillator has changed state.
The p2mpRfRxOscState specifies the current state of
the oscillator. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.3 |
p2mpTrapRfTxOscThe RF transmit frequency oscillator has changed state.
The p2mpRfRxOscState specifies the state of the
oscillator. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.4 |
p2mpTrapRfTempThe temperature of the RF module identified by p2mpRfIndex
has exceeded a defined reference. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.5 |
p2mpTrapRfCommLinkErrorThis trap indicates that the host and the IF module cannot
communicate with the RF resource identified by p2mpRfType. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.6 |
p2mpTrapTxPowerThis trap indicates that the transmit power for the RF resource
identified by p2mpRfType exceeded a predefined threshold. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.7 |
p2mpTrapRfStatusChangeThis trap indicates that the RF resource either came online(1)
or went offline(2). TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.8 |
p2mpTrapHeIfRxOscThe IF receive frequency oscillator has changed state. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.9 |
p2mpTrapHeIfTxOscThe IF transmit frequency oscillator has changed state. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.10 |
p2mpTrapHeIfExtRefOscThe IF Reference Frequency oscillator has changed state. TRAP-TYPE .1.3.6.1.4.1.9.9.170.2.0.11 |