CISCO-WIRELESS-EXP-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CISCO-WIRELESS-EXP-MIB.
74
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
74 total| Object Name |
|---|
ciscoWirelessExpMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52 |
SNMPv2-SMI-v1 Unknown .1.3.6.1.4.1.9.10.52 |
cwrRadioExpMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.1 |
cwrRadioFreqEntityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.1.1 |
cwrRfEntityTableThis table contains information about the radio frequency resources
available for use on the system. SEQUENCE OF CwrRfEntityEntry .1.3.6.1.4.1.9.10.52.1.1.1 |
cwrRfEntityEntryThis represents one entry in the cwrRfEntityTable. This table is
largely a read only table which provides details on the radio frequency
resources available on the system. Physically each RF resource may be
realized by one antenna and its associated control hardware.
But a single antenna and its associated hardware may act as more than
1 RF resource.
A Duplexor is a mechanical device, that acts as a band pass filter
when installed in an RF resource.
Normally a RF resource is capable of operating over a wide frequency
range. To operate at restricted frequencies, the user has to own that
part of the frequency spectrum. Since the user may not own parts of
the frequency spectrum over which the RF resource may operate, a
Duplexor is installed in the RF resource. This restricts the
RF resource to operate in the passband defined by the Duplexor.
In this table the Duplexor's are identified by an index into the
cwrDuplexorTable.
It is indexed by the ifIndex and cwrRfEntityIndex. CwrRfEntityEntry .1.3.6.1.4.1.9.10.52.1.1.1.1 |
cwrRfEntityIndexThis object represents the index of this entry in the
cwrRfEntityTable. Integer32 .1.3.6.1.4.1.9.10.52.1.1.1.1.1 |
cwrRfSwRevisionThis object represents the software revision number of controlling the
RF subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.2 |
cwrRfAssemblyPartNumberClassThis object represents the assembly part number class of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.3 |
cwrRfAssemblyPartNumberBaseThis object represents the assembly part number base of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.4 |
cwrRfAssemblyPartNumberVersionThis object represents the assembly part number version of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.5 |
cwrRfBoardPartNumberClassThis object represents the board part number class of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.6 |
cwrRfBoardPartNumberBaseThis object represents the board part number base of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.7 |
cwrRfBoardPartNumberVersionThis object represents the board part number version of the RF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.1.1.8 |
cwrRfBoardRevisionThis object represents the board revision of the RF subsystem.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.1.1.9 |
cwrRfSerialNumberThis object represents the serial number of the RF subsystem.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.1.1.10 |
cwrRfManfDateThis object represents the manufacturing date of the RF subsystem.ro DateAndTime -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.1.1.11 |
cwrRfVendorIdThis object represents the Radio frequency device vendor ID.ro Integer32 .1.3.6.1.4.1.9.10.52.1.1.1.1.12 |
cwrRfDuplexorIndexThis object represents the index into cwrDuplexorTable.
This index identifies the Duplexor associated with this
RF resource.ro Integer32 .1.3.6.1.4.1.9.10.52.1.1.1.1.13 |
cwrIntFreqEntityTableThis table contains information about the intermediate frequency
subsystem on the radio card. SEQUENCE OF CwrIntFreqEntityEntry .1.3.6.1.4.1.9.10.52.1.1.2 |
cwrIntFreqEntityEntryThis represents one entry in the cwrIntFreqEntityTable. This table
is largely a read only table which provides details on the intermediate
frequency subsystem available on the radio card.
It is indexed by the ifIndex. CwrIntFreqEntityEntry .1.3.6.1.4.1.9.10.52.1.1.2.1 |
cwrIfAssemblyPartNumberClassThis object represents the assembly part number class of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.1 |
cwrIfAssemblyPartNumberBaseThis object represents the assembly part number base of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.2 |
cwrIfAssemblyPartNumberVersionThis object represents the assembly part number version of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.3 |
cwrIfBoardPartNumberClassThis object represents the board part number class of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.4 |
cwrIfBoardPartNumberBaseThis object represents the board part number base of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.5 |
cwrIfBoardPartNumberVersionThis object represents the board part number version of the IF
subsystem.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.6 |
cwrIfBoardRevisionThis object represents the board revision of the IF subsystem.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.2.1.7 |
cwrIfSerialNumberThis object represents the serial number of the IF subsystem.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.2.1.8 |
cwrIfManfDateThis object represents the manufacturing date of the IF subsystem.ro DateAndTime -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.1.2.1.9 |
cwrIfVendorIdThis object represents the IF vendor ID.ro Integer32 .1.3.6.1.4.1.9.10.52.1.1.2.1.10 |
cwrIfSwRevisionThis object represents the IF software revision.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.1.2.1.11 |
cwrRadioImageGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.1.2 |
cwrImageTableThis table provides facilities to manage the firmware images that the
router will use to configure the radio line cards.
When images need to be downloaded, the software will
search this list starting from the first, for an image whose
capabilities match the configuration specified in the
cwrRadioBaseTable and the cwrRadioPhyTable and download that image
to the appropriate hardware component.
Insertion into the table at arbitrary points is not supported.
Any new image URL added to this table will be inserted at index
1 only.
Also note that an image gets downloaded to the hardware only when
when a radio link is administratively enabled. SEQUENCE OF CwrImageEntry .1.3.6.1.4.1.9.10.52.1.2.1 |
cwrImageEntryThis represents one entry in the cwrImageTable. CwrImageEntry .1.3.6.1.4.1.9.10.52.1.2.1.1 |
cwrImageIndexThis represents the one entry in this table. It also represents
the search order. When images need to be downloaded to the
hardware, the images are searched in the order of this index
for an image that matches the hardware capabilities and uses it. Integer32 .1.3.6.1.4.1.9.10.52.1.2.1.1.1 |
cwrImageNameUrlThis object is the name of the image in the Universal Resource Locator
(URL) format. This URL will be used to access the image when needed.rw DisplayString .1.3.6.1.4.1.9.10.52.1.2.1.1.2 |
cwrImageStateThis represents the state of the image.
image_invalid(1): If the image could not be accessed for any reason.
image_valid(2) : Image accessible and available for use.ro Enumeration .1.3.6.1.4.1.9.10.52.1.2.1.1.3 |
cwrImageSizeThis represents the size of the image in bytes.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.4 |
cwrImageChipClassThis represents the class of chips onto which this image may be
loaded.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.5 |
cwrImageChipTypeThis represents the download method to use.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.6 |
cwrImageCapability1This represents a bitmask. The bit mask identifies the capabilities of
this image. See also cwrImageCapability2.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.7 |
cwrImageCapability2This represents a bitmask. The bit mask identifies the capabilities of
this image in addition to cwrImageCapability1.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.8 |
cwrImageVersionThis represents the version number of this image.ro Unsigned32 -- Rsyntax Gauge32 .1.3.6.1.4.1.9.10.52.1.2.1.1.9 |
cwrImageTagThis object is the tag string associated with the image. Normally used
to trace the source code used to generate this image.ro DisplayString .1.3.6.1.4.1.9.10.52.1.2.1.1.10 |
cwrImageOpThis object represents the operation to be performed on the
identified image.
nop(0) - This value will be returned when this object is
read.
add(1) - Will add the image URL, as the first entry in the image
table.
delete(2) - Will delete the specified ULR from the image table.
move(3) - Will make the image specified by the URL the first entry
in the imageTable.rw Enumeration .1.3.6.1.4.1.9.10.52.1.2.1.1.11 |
cwrRadioLedGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.1.3 |
cwrLedTableEntity (Light emitting diode) LED information. For each LED on the
entity, an entry will exist in this table, describing the location
and current status of that LED. SEQUENCE OF CwrLedEntry .1.3.6.1.4.1.9.10.52.1.3.1 |
cwrLedEntryAn entry in the table, containing the LED information
about the entity. The entPhysicalIndex identifies
the entity on which the Led's are present. CwrLedEntry .1.3.6.1.4.1.9.10.52.1.3.1.1 |
cwrLedIndexFor a given entPhysicalIndex, this index value uniquely identifies
an entry in the cwrLedTable. INTEGER .1.3.6.1.4.1.9.10.52.1.3.1.1.1 |
cwrLedNameThe label of the LED on the physical entity or a textual
description to identify the usage of the LED.ro DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.3.1.1.2 |
cwrLedVerticalPositionThe position of the LED in the entity. It is counted from
top to bottom.ro Integer32 .1.3.6.1.4.1.9.10.52.1.3.1.1.3 |
cwrLedHorizontalPositionThe position of the LED in the entity. It is counted from
from left to right.ro Integer32 .1.3.6.1.4.1.9.10.52.1.3.1.1.4 |
cwrLedModeThis objects specifies the desired mode of LED updates.
automatic(1) and latched(2) are settings used by the software
to determine how the LED should be updated.
The others are for diagnostic purposes. The LED will be turned on
or off as specified by the other (3-8) settings.
The modes mean the following:
automatic(1): The system updates the LED according to the
default settings for that entity.
latched(2): Once the LED is turned on, user has to turn it off.
This applies only to alarm LEDs.
forceOff(3): Force the LED off.
forceSolidGreen(4): Force the LED to be solid green in on state.
forceSolidYellow(5):Force the LED to be solid Yellow in on state
forceBlinkGreen(6): Force the LED to blink in Green.
forceBlinkYellow(7):Force the LED to blink in Yellow.
forceBlinkBoth(8): Force the LED to blink Yellow and
Green alternatively.rw Enumeration .1.3.6.1.4.1.9.10.52.1.3.1.1.5 |
cwrLedCurrentColorIndicates the current color of the LED.ro Enumeration .1.3.6.1.4.1.9.10.52.1.3.1.1.6 |
cwrRadioDuplexorGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.1.4 |
cwrDuplexorTableThis table contains information about the Duplexors
available for use on the system. SEQUENCE OF CwrDuplexorEntry .1.3.6.1.4.1.9.10.52.1.4.1 |
cwrDuplexorEntryThis represents one entry in the cwrDuplexorTable. This table
provides details on the Duplexors available on the system.
It is indexed by the ifIndex and cwrDuplexorIndex. CwrDuplexorEntry .1.3.6.1.4.1.9.10.52.1.4.1.1 |
cwrDuplexorIndexThis object represents the index of this entry in the
cwrDuplexorTable. Integer32 .1.3.6.1.4.1.9.10.52.1.4.1.1.1 |
cwrDuplexorCiscoPartNumberThis object represents the Cisco part number for this Duplexor.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.2 |
cwrDuplexorLoPassbandRangeThis object represents the low frequency range that this Duplexor will
pass through without any attenuation. All low frequencies outside this
range will be attenuated to a level such that an RF resource that
uses this Duplexor will be unable to transmit or receive those
frequencies.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.3 |
cwrDuplexorHiPassbandRangeThis object represents the high frequency range that this Duplexor will
pass through without any attenuation. All high frequencies outside this
range will be attenuated to a level such that an RF resource that
uses this Duplexor will be unable to transmit or receive those
frequencies.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.4 |
cwrDuplexorReceivePassbandThis object indicates which of the two passbands are being used
to receive transmissions. The RF Resource can receive on either of
the duplexor passbands.
loPassband(1) - The RF Resource is receiving on a frequency within
the range identified by cwrDuplexorLoPassbandRange.
hiPassband(2) - The RF Resource is receiving on a frequency within
the range identified by cwrDuplexorHiPassbandRange.rw Enumeration .1.3.6.1.4.1.9.10.52.1.4.1.1.5 |
cwrDuplexorCLEICodeThe CLEI code for this Duplexor.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.6 |
cwrDuplexorVendorNameThe Vendor Name for this Duplexor.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.7 |
cwrDuplexorSerialNumberThe Serial number of this Duplexor.rw DisplayString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.10.52.1.4.1.1.8 |
cwrRadioExpConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2 |
cwrRadioExpCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.1 |
cwrRadioExpCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.1.1 |
cwrRadioExpGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.2 |
cwrComplianceRadioRFGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.2.1 |
cwrComplianceRadioImageGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.2.2 |
cwrComplianceRadioLEDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.2.3 |
cwrComplianceRadioDuplexorGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.52.2.2.4 |