CISCO-WAN-3G-MIB
AI MIB Summary
The CISCO-WAN-3G-MIB enables SNMP-based monitoring and management of Cisco cellular WAN interfaces supporting 3G, 4G LTE, and legacy CDMA/GSM technologies by exposing critical RF link quality metrics (such as RSSI, Ec/Io, SNR, and BER), network attachment states, and data session parameters for UMTS, HSPA, and LTE protocols.
This MIB module provides network management support for Cisco cellular 3G and 4G LTE WAN products.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
1xRTT - 1 times Radio Transmission Technology.
3G - Third generation of mobile phones standards and technologies.
4G - Fourth generation of mobile phones standards and technologies
Azimuth - Angle of rotation of a satellite Dish.
BER - Bit Error Ratio.
BS - Base Station.
CDMA - Code Division Multiple Access.
dB - decibel.
dBm - power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW).
CnS - Control and Status proprietary protocol for managing the control and status of the modem.
Ec/Io - ratio of received pilot energy, Ec, to total received energy or the total power spectral density, Io.
EDGE - Enhanced Data rate for GSM Evolution.
EPS - Evolved Packet System
EVDO - EVolution Data Optimized.
FDD - Frequency Division Duplexing
GPRS - General Packet Radio Service.
GSM - Global System for Mobile communications.
GPS - Global Positioning System.
HSDPA - High Speed Downlink Packet Access.
HSPA - High Speed Packet Access.
HSUPA - High Speed Uplink Packet Access.
LBS - Location Based Service.
LTE - Long Term Evolution
MT - Mobile Termination.
PDP - Packet Data Protocol.
PLMN - Public Land Mobile Network.
QoS - Quality of Service.
RSSI - Received Signal Strength Indication.
SDU - Service Data Unit.
SER - SDU Error Ratio.
SIM - Subscriber Identity Module.
SMS - Short Messaging Service.
SNR - Signal to Noise Ratio.
TDD - Time Division Duplexing
UMTS - Universal Mobile Telecommunication System.
WCDMA - Wideband Code Division Multiple Access.
Main OID:
ciscoWan3gMIB.1.3.6.1.4.1.9.9.661
368
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
368 total| Object Name |
|---|
ciscoWan3gMIBThis MIB module provides network management
support for Cisco cellular 3G and 4G LTE WAN products.
*** ABBREVIATIONS, ACRONYMS, AND SYMBOLS ***
1xRTT - 1 times Radio Transmission Technology.
3G - Third generation of mobile phones standards and
technologies.
4G - Fourth generation of mobile phones standards and
technologies
Azimuth - Angle of rotation of a satellite Dish.
BER - Bit Error Ratio.
BS - Base Station.
CDMA - Code Division Multiple Access.
dB - decibel.
dBm - power ratio in decibels (dB) of the measured power
referenced to one milliwatt (mW).
CnS - Control and Status proprietary protocol for
managing the control and status of the modem.
Ec/Io - ratio of received pilot energy, Ec, to total received
energy or the total power spectral density, Io.
EDGE - Enhanced Data rate for GSM Evolution.
EPS - Evolved Packet System
EVDO - EVolution Data Optimized.
FDD - Frequency Division Duplexing
GPRS - General Packet Radio Service.
GSM - Global System for Mobile communications.
GPS - Global Positioning System.
HSDPA - High Speed Downlink Packet Access.
HSPA - High Speed Packet Access.
HSUPA - High Speed Uplink Packet Access.
LBS - Location Based Service.
LTE - Long Term Evolution
MT - Mobile Termination.
PDP - Packet Data Protocol.
PLMN - Public Land Mobile Network.
QoS - Quality of Service.
RSSI - Received Signal Strength Indication.
SDU - Service Data Unit.
SER - SDU Error Ratio.
SIM - Subscriber Identity Module.
SMS - Short Messaging Service.
SNR - Signal to Noise Ratio.
TDD - Time Division Duplexing
UMTS - Universal Mobile Telecommunication System.
WCDMA - Wideband Code Division Multiple Access. MODULE-IDENTITY .1.3.6.1.4.1.9.9.661 |
ciscoWan3gMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.0 |
c3gModemUpNotifThis is the notification that the modem has been detected by
host interface. Users can enable or disable the generation of
this notification by using object c3gModemUpNotifEnabled. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.1 |
c3gModemDownNotifThis is the notification that the modem has not been detected
by host interface, or has been disconnected from host interface.
Users can enable or disable the generation of this notification
by using object c3gModemDownNotifEnabled. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.2 |
c3gServiceChangedNotifNotification for service change event. Objects
c3gPreviousServiceType and c3gCurrentServiceType will be
included in the notification. Users can enable or disable the
generation of this notification by using object
c3gServiceChangedNotifEnabled. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.3 |
c3gNetworkChangedNotifNotification for network change event. Objects c3gCurrentSid,
c3gCurrentNid, c3gGsmMcc, c3gGsmMnc and c3gRoamingStatus will
be included in the notification. Users can enable or disable
the generation of this notification by using object
c3gNetworkChangedNotifEnabled. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.4 |
c3gConnectionStatusChangedNotifNotification for connection status change event. Objects
c3gConnectionStatus and c3gCurrentServiceType will be included
in the notification. Users can use object
c3gConnectionStatusChangedNotifFlag to control what connection
status changes will cause the generation of this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.5 |
c3gRssiOnsetNotifIf RSSI goes below c3gRssiOnsetNotifThreshold and the service
bit in c3gRssiOnsetNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated RSSI
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
is used to indicate the RSSI value that triggers the
notification, user should go to the corresponding radio table to
get the current RSSI value. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.6 |
c3gRssiAbateNotifIf RSSI goes above c3gRssiAbateNotifThreshold and the service
bit in c3gRssiAbateNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated RSSI
will be reported in c3gNotifRssi. Please note that c3gNotifRssi
is used to indicate the RSSI value that triggers the
notification, user should go to the corresponding radio table to
get the current RSSI value. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.7 |
c3gEcIoOnsetNotifIf Ec/Io goes below c3gEcIoOnsetNotifThreshold and the service
bit in c3gEcIoOnsetNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated Ec/Io
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
is used to indicate the Ec/Io value that triggers the
notification, user should go to the corresponding radio table to
get the current Ec/Io value. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.8 |
c3gEcIoAbateNotifIf Ec/Io goes above c3gEcIoAbateNotifThreshold and the service
bit in c3gEcIoAbateNotifFlag is set, this notification will be
generated. Object c3gNotifRadioService will indicate which
service generates this notification and the associated Ec/Io
will be reported in c3gNotifEcIo. Please note that c3gNotifEcIo
is used to indicate the Ec/Io value that triggers the
notification, user should go to the corresponding radio table to
get the current Ec/Io value. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.9 |
c3gModemTemperOnsetNotifIf modem temperature goes above
c3gModemTemperOnsetNotifThreshold and the value of
c3gModemTemperOnsetNotifEnabled is 'true', this notification
will be generated and the current value of c3gModemTemperature
will be included in this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.10 |
c3gModemTemperAbateNotifIf modem temperature goes below
c3gModemTemperAbateNotifThreshold and the value of
c3gModemTemperAbateNotifEnabled is 'true', this notification
will be generated and the current value of c3gModemTemperature
will be included in this notification. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.11 |
c3gModemTemperOnsetRecoveryNotifThis trap is generated as a recovery notification for
c3gModemTemperOnsetNotif.This trap is generated when the current
value of c3gModemTemperature goes below
c3gModemTemperOnsetNotifThreshold once it has generated the
c3gModemTemperOnsetNotif and the value of
c3gModemTemperOnsetNotifEnabled is 'true'.
c3gModemTemperature contains the current value of modem
temperature. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.12 |
c3gModemTemperAbateRecoveryNotifThis trap is generated as a recovery notification for
c3gModemTemperAbateNotif.This trap is generated when the current
value of c3gModemTemperature goes above
c3gModemTemperAbateNotifThreshold once it has generated the
c3gModemTemperAbateNotif and the value of
c3gModemTemperAbateNotifEnabled is 'true'
c3gModemTemperature contains the current value of modem
temperature NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.661.0.13 |
ciscoWan3gMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1 |
c3gWanCommonTableCellular common objects table which is technology
independent. SEQUENCE OF C3gWanCommonEntry .1.3.6.1.4.1.9.9.661.1.1 |
c3gWanCommonEntryAn entry (conceptual row) in the c3gWanCommonTable. C3gWanCommonEntry .1.3.6.1.4.1.9.9.661.1.1.1 |
c3gStandardCellular Standard: GSM (Global System for Mobile
communications, 3GPP), CDMA (Code Division Multiple
Access, 3GPP-2). GSM standard also include 4G-LTE
technology modero Enumeration .1.3.6.1.4.1.9.9.661.1.1.1.1 |
c3gCapabilityCellular service capability. It currently includes the 2G,
3G and 4G-LTE standard.ro C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.2 |
c3gModemStateCellular modem state, up(2) indicates modem can be detected
and down(3) indicates modem can not be detected.ro Enumeration .1.3.6.1.4.1.9.9.661.1.1.1.3 |
c3gPreviousServiceTypeThis object indicates the previous service type when service
type changes.ro C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.4 |
c3gCurrentServiceTypeThis object indicates the current service type when service
type changes.ro C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.5 |
c3gRoamingStatusCellular current roaming status.ro Enumeration .1.3.6.1.4.1.9.9.661.1.1.1.6 |
c3gCurrentSystemTimeCellular current system time received from base station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.1.1.7 |
c3gConnectionStatusIndicates the current connection status.ro Enumeration .1.3.6.1.4.1.9.9.661.1.1.1.8 |
c3gNotifRadioServiceThis object is used as one of the var-bind object when
notification for RSSI or Ec/Io is generated. This object
indicates which service generates the notification.ro C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.9 |
c3gNotifRssiThis object is used as one of the var-bind object when
notification for RSSI is generated. The relevant RSSI will be
copied into c3gNotifRssi which corresponds to the service
indicated in c3gNotifRadioService object. This object will
reflect the value of one of the following objects:
c3gCurrent1xRttRssi, c3gCurrentEvDoRssi and c3gCurrentGsmRssi.
User should not use this object to get the current RSSI value as
this object is used to indicate the RSSI value that triggers
c3gRssiOnsetNotif or c3gRssiAbateNotif notification.ro C3gRssi .1.3.6.1.4.1.9.9.661.1.1.1.10 |
c3gNotifEcIoThis object is used as one of the var-bind object when
notification for Ec/Io is generated. The relevant Ec/Io will
be copied into c3gNotifEcIo which corresponds to the service
indicated in c3gNotifRadioService object. This object will
reflect the value of one of the following objects:
c3gCurrent1xRttEcIo, c3gCurrentEvDoEcIo and c3gCurrentGsmEcIo.
User should not use this object to get the current Ec/Io value
as this object is used to indicate the Ec/Io value that triggers
c3gEcIoOnsetNotif or c3gEcIoAbateNotif notification.ro C3gEcIo .1.3.6.1.4.1.9.9.661.1.1.1.11 |
c3gModemTemperatureThe modem temperature.ro C3gTemperature UNITS "degrees Celsius" .1.3.6.1.4.1.9.9.661.1.1.1.12 |
c3gRssiOnsetNotifThresholdThe RSSI onset threshold value. If RSSI goes below the
threshold and the service bit in c3gRssiOnsetNotifFlag is
set, the c3gRssiOnsetNotif notification for that service
will be sent. The absolute value of
c3gRssiAbateNotifThreshold should be less than or equal to
the absolute value of c3gRssiOnsetNotifThreshold
(|c3gRssiAbateNotifThreshold| <= |c3gRssiOnsetNotifThreshold|).
e.g. setting c3gRssiAbateNotifThreshold to -115 dBm and then
setting c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
and will be rejected.rw C3gRssi UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.1.1.13 |
c3gRssiAbateNotifThresholdThe RSSI abate threshold value. If RSSI goes above the
threshold and the service bit in c3gRssiAbateNotifFlag is
set, the c3gRssiAbateNotif notification for that service will
be sent. The absolute value of c3gRssiAbateNotifThreshold
should be less than or equal to the absolute value of
c3gRssiOnsetNotifThreshold (|c3gRssiAbateNotifThreshold| <=
|c3gRssiOnsetNotifThreshold|). e.g. setting
c3gRssiAbateNotifThreshold to -115 dBm and then setting
c3gRssiOnsetNotifThreshold to -110 dBm is not allowed
and will be rejected.rw C3gRssi UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.1.1.14 |
c3gEcIoOnsetNotifThresholdThe EcIo onset threshold value. If EcIo goes below the
threshold and the service bit in c3gEcIoOnsetNotifFlag is set,
the c3gEcIoOnsetNotif notification for that service will be
sent. The absolute value of c3gEcIoAbateNotifThreshold should
be less than or equal to the absolute value of
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|c3gEcIoOnsetNotifThreshold|). e.g. setting
c3gEcIoAbateNotifThreshold to -15 dB and then setting
c3gEcIoOnsetNotifThreshold to -10 dB is not allowed and will
be rejected.rw C3gEcIo UNITS "dB" .1.3.6.1.4.1.9.9.661.1.1.1.15 |
c3gEcIoAbateNotifThresholdThe threshold value that if EcIo goes above the threshold and
the service bit in c3gEcIoAbateNotifFlag is set, the
c3gEcIoAbateNotif notification for that service will be sent.
The absolute value of c3gEcIoAbateNotifThreshold
should be less than or equal to the absolute value of
c3gEcIoOnsetNotifThreshold (|c3gEcIoAbateNotifThreshold| <=
|c3gEcIoOnsetNotifThreshold|). e.g. setting
c3gEcIoOnsetNotifThreshold to -15 dB and then setting
c3gEcIoAbateNotifThreshold to -10 dB is not allowed and will
be rejected.rw C3gEcIo UNITS "dB" .1.3.6.1.4.1.9.9.661.1.1.1.16 |
c3gModemTemperOnsetNotifThresholdThe modem temperature onset threshold value. If modem
temperature goes above the threshold and the value of
c3gModemTemperOnsetNotifEnabled is 'true',
the c3gModemTemperOnsetNotif notification will be sent.
The value of c3gModemTemperAbateNotifThreshold should be less
than or equal to the value of
c3gModemTemperOnsetNotifThreshold. e.g. setting
c3gModemTemperAbateNotifThreshold to 50 degree Celsius and
then setting c3gModemTemperOnsetNotifThreshold to
40 degree Celsius is not allowed and will be rejected.rw C3gTemperature UNITS "degrees Celsius" .1.3.6.1.4.1.9.9.661.1.1.1.17 |
c3gModemTemperAbateNotifThresholdThe modem temperature abate threshold value. If modem
temperature goes below the threshold and the value of
c3gModemTemperAbateNotifEnabled is 'true', the
c3gModemTemperAbateNotif notification will be sent. The value
of c3gModemTemperAbateNotifThreshold should be less than or
equal to the value of c3gModemTemperOnsetNotifThreshold.
e.g. setting c3gModemTemperAbateNotifThreshold to 50 degree
Celsius and then setting c3gModemTemperOnsetNotifThreshold
to 40 degree Celsius is not allowed and will be rejected.rw C3gTemperature UNITS "degrees Celsius" .1.3.6.1.4.1.9.9.661.1.1.1.18 |
c3gModemResetThis object is used to reset or power-cycle the modem.rw Enumeration .1.3.6.1.4.1.9.9.661.1.1.1.19 |
c3gModemUpNotifEnabledThis object is used to enable/disable the generation of modem
up notification c3gModemUpNotif.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.20 |
c3gModemDownNotifEnabledThis object is used to enable/disable the generation of modem
down notification c3gModemDownNotif.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.21 |
c3gServiceChangedNotifEnabledThis object is used to enable/disable the generation of service
changed notification c3gServiceChangedNotif.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.22 |
c3gNetworkChangedNotifEnabledThis object is used to enable/disable the generation of network
changed notification c3gNetworkChangedNotif.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.23 |
c3gConnectionStatusChangedNotifFlagThis object is the flag bitmap to control the generation of
notification c3gConnectionStatusChangedNotif. e.g. setting bit
0 (error(0)) to 1 and bit 4 (disconnected(4)) to 1 will cause
the notification c3gConnectionStatusChangedNotif to be
generated when object c3gConnetionStatus changes the status to
error or disconnected. The default value of this object is
'00'H.rw Bits .1.3.6.1.4.1.9.9.661.1.1.1.24 |
c3gRssiOnsetNotifFlagThis object is the flag bitmap to control the generation of
notification c3gRssiOnsetNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gRssiOnsetNotif for that service. The default value of this
object is all bits are 0.rw C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.25 |
c3gRssiAbateNotifFlagThis object is the flag bitmap to control the generation of
notification c3gRssiAbateNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gRssiAbateNotif for that service. The default value of this
object is all bits are 0.rw C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.26 |
c3gEcIoOnsetNotifFlagThis object is the flag bitmap to control the generation of
notification c3gEcIoOnsetNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gEcIoOnsetNotif for that service. The default value of this
object is all bits are 0.rw C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.27 |
c3gEcIoAbateNotifFlagThis object is the flag bitmap to control the generation of
notification c3gEcIoAbateNotif. Each bit represents a service
as defined in C3gServiceCapability, set the bit value to 1 to
enable (and 0 to disable) the generation of notification
c3gEcIoAbateNotif for that service. The default value of this
object is all bits are 0.rw C3gServiceCapability .1.3.6.1.4.1.9.9.661.1.1.1.28 |
c3gModemTemperOnsetNotifEnabledThis object is used to enable/disable the generation of
c3gModemTemperOnsetNotif notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.29 |
c3gModemTemperAbateNotifEnabledThis object is used to enable/disable the generation of
c3gModemTemperAbateNotif notification.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.30 |
c3gGpsStateThis object is used to determine or enable/disable
the GPS state.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.1.1.31 |
c3gWanCdma OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.2 |
c3gCdmaSessionTableThis table describes wireless session (link) created when a
modem connects to a particular cellular network. One or more
logical calls can be placed over wireless session(link). These
logical calls are represented in the c3gCdmaConnectionTable. SEQUENCE OF C3gCdmaSessionEntry .1.3.6.1.4.1.9.9.661.1.2.1 |
c3gCdmaSessionEntryAn entry (conceptual row) in the c3gCdmaSessionTable. C3gCdmaSessionEntry .1.3.6.1.4.1.9.9.661.1.2.1.1 |
c3gCdmaTotalCallDurationTotal duration of all calls.ro Counter64 UNITS "seconds" .1.3.6.1.4.1.9.9.661.1.2.1.1.1 |
c3gCdmaTotalTransmittedTotal data transmitted for all calls. It is the total amount
of data transmitted by modem, not to be confused with the number
of bytes transmitted through the interface.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.2.1.1.2 |
c3gCdmaTotalReceivedTotal data received for all calls. It is the total amount of
data received by modem, not to be confused with the number of
bytes received from the interface.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.2.1.1.3 |
c3gHdrDdtmPreferenceHDR Data Dedicated Transmission Mode (DDTM) preference:
unknown(1) - DDTM preference is unknown
off(2) - DDTM preference set to OFF
on(3) - DDTM preference set to ON
noChange(4) - DDTM preference is no changerw Enumeration .1.3.6.1.4.1.9.9.661.1.2.1.1.4 |
c3gCdmaConnectionTableCellular 3G CDMA connection table. This table describes
logical connections/calls over wireless link, the wireless link
is described in c3gCdmaSessionTable. SEQUENCE OF C3gCdmaConnectionEntry .1.3.6.1.4.1.9.9.661.1.2.2 |
c3gCdmaConnectionEntryAn entry (conceptual row) in the c3gCdmaConnectionTable. C3gCdmaConnectionEntry .1.3.6.1.4.1.9.9.661.1.2.2.1 |
c3gOutgoingCallNumberPhone number of outgoing call.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.2.1.1 |
c3gHdrAtStateHigh Data Rate (HDR) Access Terminal (AT) state.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.2 |
c3gHdrSessionStateHigh Data Rate (HDR) session state.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.3 |
c3gUatiUnicast Access Terminal Identifier (UATI), AT seeking access
to the 1 times EV-DO system receives a UATI allocated from the
system after setting up a radio traffic channel with a base
station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.2.1.4 |
c3gColorCodeColor code. A sync channel may be used by the base station
to communicate administrative information to a mobile station.
For example, a base station may transmit a base station ID to a
user, a color code and administrative information identifying
system status.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.2.1.5 |
c3gRatiRandom Access Terminal Identifier (RATI). AT transmits a
UATI request message to the ANC using the RATI to make a UATI
allocation request.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.2.1.6 |
c3gHdrSessionDurationHDR connection session duration. It is the duration
between c3gHdrSessionStart and c3gHdrSessionEnd.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.661.1.2.2.1.7 |
c3gHdrSessionStartHDR connection session starting time.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.661.1.2.2.1.8 |
c3gHdrSessionEndHDR connection session ending time.ro Unsigned32 UNITS "milliseconds" .1.3.6.1.4.1.9.9.661.1.2.2.1.9 |
c3gAuthStatusConnection authentication status:
unknown(1) - authentication status is unknown
notAuthenticated(2) - not yet authenticated.
authenticated(3) - authenticated.
failed(4) - authentication failed.
authenticationDisabled(5) - authentication disabledro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.10 |
c3gHdrDrcHigh Data Rate (HDR) Data Rate Control (DRC). AT provides
requests for data transmissions by sending a Data Rate Control,
DRC, message via a specific channel referred to as the DRC
channel.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.2.1.11 |
c3gHdrDrcCoverHDR DRC cover. The DRC cover is a coding applied to
identify the sector from which the data is to be transmitted.
In one embodiment, the DRC cover is a Walsh code applied to
the DRC value, wherein a unique code corresponds to each sector
in the Active Set of the AT.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.2.1.12 |
c3gHdrRriHDR Rate Request Indicator (RRI). RRI provides the
structure of a frame currently being transmitted when frames
are transmitted at different rates. Services at different rates
are reliably provided by the RRI:
unknown(1) - RRI unknown
pilotOnly(2) - pilot channel only
rri9dot6kbps(3) - RRI is 9.6 Kbit/s
rri19dot2kbps(4) - RRI is 19.2 Kbit/s
rri38dot4kbps(5) - RRI is 38.4 Kbit/s
rri76dot8kbps(6) - RRI is 76.8 Kbit/s
rri153dot6kbps(7) - RRI is 153.6 Kbit/sro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.13 |
c3gMobileIpErrorCodeMobile IP error code (please refer to RFC 2002).ro Integer32 .1.3.6.1.4.1.9.9.661.1.2.2.1.14 |
c3gCdmaCurrentTransmittedCurrent number of bytes transmitted by modem for current
connection.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.2.2.1.15 |
c3gCdmaCurrentReceivedCurrent number of bytes received by modem for current
connection.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.2.2.1.16 |
c3gCdmaCurrentCallStatusCurrent call status.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.17 |
c3gCdmaCurrentCallDurationCurrent call duration.ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.9.9.661.1.2.2.1.18 |
c3gCdmaCurrentCallTypeCurrent call type.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.19 |
c3gCdmaLastCallDisconnReasonLast call disconnect reason:
unknown(1) - Unknown
modemOffline(2) - Modem offline
modemCdmaLocTilPowCyc(3) - Modem CDMA locked till power cycle
noService(4) - No service
abnormalCallEnd(5) - Abnormal call end
baseStatIntercept(6) - Base station intercept
baseStatRelease(7) - Base station release
baseStatReleaseNoReas(8) - Base station release (No reason)
baseStatReleaseSoRej(9) - Base station release (SO reject)
incomingCall(10) - Incoming call
baseStatAlertStop(11) - Base station alert stop
clientEndedCall(12) - Client ended call
activationEndedOtasp(13) - Activation ended OTASP (Over-
The-Air Service Provisioning)
ndssFailure(14) - NDSS (Network and Distributed
System Security) failure
maxAccesProbTransmit(15) - Max access probes transmitted
persistTestFailure(16) - Persistence test failure
ruimNotPresent(17) - RUIM (Removable User Identity
Module) not present
accessAttemptInProg(18) - Access attempt in progress
reasonUnspecified(19) - Reason unspecified
recdRetryOrder(20) - Recd retry order
modemLocked(21) - Modem Locked
gpsCallEnded(22) - GPS call ended
smsCallEnded(23) - SMS (Short Message Service)
call ended
noConcurrentService(24) - No concurrent service
noResponseFromBs(25) - No response from BS (Base station)
rejectedByBs(26) - Rejected by BS
notCompatConcurServ(27) - Not compatible concurrent service
accessBlockedByBs(28) - Access blocked by BS
alreadyOnTraffChann(29) - Already on Traffic channel
emergencyCall(30) - Emergency call
dataCallEnded(31) - Data call ended
busyHdr(32) - Busy (HDR)
billingOrAuthErrHdr(33) - Billing or Auth error (HDR)
sysChangeDueToPrlHdr(34) - System change due to PRL (HDR)
hdrExitDueToPrl(35) - HDR exit due to PRL (HDR)
noSessionHdr(36) - No Session (HDR)
callEndedHdr(37) - Call ended (HDR)ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.20 |
c3gCdmaLastConnErrorLast connect error:
none(1) - None
invalidClientId(2) - Invalid client ID
badCallType(3) - Bad call type
badServiceType(4) - Bad service type
expectingNumber(5) - Expecting number
nullNumberBuffer(6) - Null number buffer
invalidDigits(7) - Invalid digits
outOfRangeNumber(8) - Out of range number
nullAalphaBuffer(9) - Null alpha buffer
outOfRangeAlphaNumber(10) - Out of range alpha number
invalidOtaspActivatCode(11) - Invalid OTASP activation code
modemOffline(12) - Modem offline
modemLocked(13) - Modem locked
unsupportedFlash(14) - Unsupported flash
dialedNumberProhibited(15) - Dialed number prohibited
onlyE911Calls(16) - Only E911 calls
modemInUse(17) - Modem in use
unsupportedServiceType(18) - Unsupported service type
wrongCallType(19) - Wrong call type
invalidCommandCallState(20) - Invalid command (call state)
invalidCommandModemState(21) - Invalid command (modem state)
noValidService(22) - No valid service
cannotAnswerIncomingCall(23) - Cannot answer incoming call
badPrivacySetting(24) - Bad privacy setting
noCommandBuffers(25) - No command buffers
communicationProblem(26) - Communication problem
unspecifiedError(27) - Unspecified error
invalidLastActiveNetwork(28) - Invalid last active network
noCollocatedHdr(29) - No collocated HDR
uimNotPresent(30) - UIM (User Identity Module) not
presentro Enumeration .1.3.6.1.4.1.9.9.661.1.2.2.1.21 |
c3gCdmaIdentityTableCellular 3G CDMA identity table. SEQUENCE OF C3gCdmaIdentityEntry .1.3.6.1.4.1.9.9.661.1.2.3 |
c3gCdmaIdentityEntryAn entry (conceptual row) in the c3gCdmaIdentityTable. C3gCdmaIdentityEntry .1.3.6.1.4.1.9.9.661.1.2.3.1 |
c3gEsnThis object indicates Electronic Serial Number (ESN).ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.3.1.1 |
c3gModemActivationStatusModem activation status.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.3.1.2 |
c3gAccountActivationDateModem account activation date.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.3.1.3 |
c3gCdmaRoamingPreferenceThis object indicates the roaming preference:
unknown(1) - preference unknown
home(2) - home networks only
affiliated(3) - roaming on affiliated networks
any(4) - roaming on any networkrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.3.1.4 |
c3gPrlVersionPreferred Roaming List (PRL) version.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.3.1.5 |
c3gMdnMobile Directory Number (MDN), a dialable number assigned to a
wireless phone.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.3.1.6 |
c3gMsidMobile Station Identifier (MSID), MSID is utilized to
distinguish the mobile station being programmed from other
mobile stations during messaging and paging processes,
including the downloading of programming information to the
mobile station.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.3.1.7 |
c3gMslMobile Subscriber Lock (MSL).rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.3.1.8 |
c3gCdmaNetworkTableCellular 3G CDMA network table. SEQUENCE OF C3gCdmaNetworkEntry .1.3.6.1.4.1.9.9.661.1.2.4 |
c3gCdmaNetworkEntryAn entry (conceptual row) in the c3gCdmaNetworkTable. C3gCdmaNetworkEntry .1.3.6.1.4.1.9.9.661.1.2.4.1 |
c3gCdmaCurrentServiceStatusCurrent service status.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.4.1.1 |
c3gCdmaHybridModePreferenceThis object indicates the hybrid mode preference:
unknown(1) - preference unknown
hybrid(2) - connect to EV-DO/1xRTT services
evDoOnly(3) - connect to only EV-DO service
oneXRttOnly(4) - connect to only 1xRTT servicerw Enumeration .1.3.6.1.4.1.9.9.661.1.2.4.1.2 |
c3gCdmaCurrentRoamingStatusCurrent 1xRTT roaming status, roaming is a general term in
wireless telecommunications that refers to the extending of
connectivity service in a location that is different from the
home location where the service was registered:
unknown(1) - roaming status is unknown.
home(2) - connectivity service in home location.
roamingWithSid(3) - roaming with SID.
roamingWithoutSid(4) - roaming without SIDro Enumeration .1.3.6.1.4.1.9.9.661.1.2.4.1.3 |
c3gCurrentIdleDigitalModeCurrent idle digital mode:
unknown(1) - service is unknown
noService(2) - no service
amps(3) - Advanced Mobile Phone Service (AMPS)
cdma(4) - Code Division Multiple Access (CDMA)
gsm(5) - Global System for Mobile communications (GSM)
hdr(6) - High Data Rate (HDR)
wcdma(7) - Wideband Code-Division Multiple-Access (WCDMA)
gps(8) - Global Positioning System (GPS)
lte(9) - Long Term Evolution (LTE)ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.4.1.4 |
c3gCurrentSidCurrent System Identifier (SID), SID is a 15-bit numeric
identifiers used by cellular systems to identify the
home system of a cellular telephone and by the cellular
telephone to determine its roaming status. Value of '-1'
indicates SID is 'Not Applicable'.rw Integer32 (-1..32767) .1.3.6.1.4.1.9.9.661.1.2.4.1.5 |
c3gCurrentNidCurrent Network Identification (NID), NID is a 16-bit numeric
identifiers used by cellular systems. Value of '-1' indicates
NID is 'Not Applicable'.rw Integer32 (-1..65535) .1.3.6.1.4.1.9.9.661.1.2.4.1.6 |
c3gCurrentCallSetupModeCurrent call setup mode. The 1xEV-DO system supports packet
data connections to a public or private data network using
either mobile IP or simple IP protocol. For simple IP
protocol, moving from the coverage area of one PDSN to another
PDSN constitutes a change in packet data session. For mobile
IP protocol, a packet data session can span several PDSNs as
long as the user continuously maintains mobility bindings at
the Home Agent (the IP address is persistent). The modes are:
unknown(1) - mode is unknown
simpleIpOnly(2) - simple IP only
mobileIpPreferWithSipFallback(3) - prefer mobile IP with
simple IP as fallback mode
mobileIpOnly(4) - mobile IP onlyrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.4.1.7 |
c3gSipUsernameSimple IP (SIP) user name.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.4.1.8 |
c3gSipPasswordSimple IP (SIP) password.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.4.1.9 |
c3gServingBaseStationLongitudeLongitude of the serving base station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.4.1.10 |
c3gServingBaseStationLatitudeLatitude of the serving base station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.4.1.11 |
c3gCdmaProfile OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.2.5 |
c3gCdmaProfileCommonTableCellular 3G CDMA profile common table. SEQUENCE OF C3gCdmaProfileCommonEntry .1.3.6.1.4.1.9.9.661.1.2.5.1 |
c3gCdmaProfileCommonEntryAn entry (conceptual row) in the c3gCdmaProfileCommonTable. C3gCdmaProfileCommonEntry .1.3.6.1.4.1.9.9.661.1.2.5.1.1 |
c3gNumberOfDataProfileConfigurableThe number of data profiles configurable.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.5.1.1.1 |
c3gCurrentActiveDataProfileThe current active data profile.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.5.1.1.2 |
c3gCdmaProfileTableCellular 3G CDMA profile table. SEQUENCE OF C3gCdmaProfileEntry .1.3.6.1.4.1.9.9.661.1.2.5.2 |
c3gCdmaProfileEntryAn entry (conceptual row) in the c3gCdmaProfileTable. C3gCdmaProfileEntry .1.3.6.1.4.1.9.9.661.1.2.5.2.1 |
c3gCdmaProfileIndexProfile index, combined with entPhysicalIndex to access
the profile table c3gCdmaProfileTable. Integer32 .1.3.6.1.4.1.9.9.661.1.2.5.2.1.1 |
c3gNaiNetwork Access Identifier (NAI). NAI is required to identify
the mobile user and the network the mobile user intended to
access. The NAI is provided by the mobile node to the dialed
ISP during PPP authentication.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.5.2.1.2 |
c3gAaaPasswordThis object indicates the password for AAA.rw DisplayString .1.3.6.1.4.1.9.9.661.1.2.5.2.1.3 |
c3gMnHaSsMobile Node (MN) Home Agent (HA) Shared Secret (SS) setting:
set(1) - shared secret is set
notSet(2) - shared secret is not setrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.5.2.1.4 |
c3gMnHaSpiMobile Node (MN) Home Agent (HA) Security Parameter Index
(SPI).rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.5.2.1.5 |
c3gMnAaaSsMobile Node (MN) Authentication Authorization Accounting (AAA)
Shared Secret (SS) setting:
set(1) - shared secret is set
notSet(2) - shared secret is not setrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.5.2.1.6 |
c3gMnAaaSpiMobile Node (MN) Authentication Authorization Accounting (AAA)
Security Parameter Index (SPI).rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.5.2.1.7 |
c3gReverseTunnelPreferenceReverse tunnel preference.rw Enumeration .1.3.6.1.4.1.9.9.661.1.2.5.2.1.8 |
c3gHomeAddrTypeA value that represents the type of the IP Address stored in
the object c3gHomeAddr.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.9 |
c3gHomeAddrA unicast routable address assigned to a Mobile Node, used as
the permanent address of the Mobile Node.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.10 |
c3gPriHaAddrTypeA value that represents the type of the IP Address stored in
the object c3gPriHaAddr.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.11 |
c3gPriHaAddrThe primary home agent address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.12 |
c3gSecHaAddrTypeA value that represents the type of the IP Address stored in
the object c3gSecHaAddr.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.13 |
c3gSecHaAddrThe secondary home agent address.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.661.1.2.5.2.1.14 |
c3gCdmaRadio OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.2.6 |
c3gCdma1xRttRadioTableCellular 3G CDMA 1xRTT radio table. SEQUENCE OF C3gCdma1xRttRadioEntry .1.3.6.1.4.1.9.9.661.1.2.6.1 |
c3gCdma1xRttRadioEntryAn entry (conceptual row) in the c3gCdma1xRttRadioTable. C3gCdma1xRttRadioEntry .1.3.6.1.4.1.9.9.661.1.2.6.1.1 |
c3gCurrent1xRttRssiCurrent 1xRTT RSSI value.ro C3gRssi .1.3.6.1.4.1.9.9.661.1.2.6.1.1.1 |
c3gCurrent1xRttEcIoCurrent 1xRTT Ec/Io value.ro C3gEcIo .1.3.6.1.4.1.9.9.661.1.2.6.1.1.2 |
c3gCurrent1xRttChannelNumberCurrent 1xRTT channel number. Current channel number to which
the modem is attached to the base station. Value of '-1'
indicates 'No Service'.ro Integer32 .1.3.6.1.4.1.9.9.661.1.2.6.1.1.3 |
c3gCurrent1xRttChannelStateCurrent 1xRTT channel state. Indicates whether the modem is
scanning or has acquired the channel.ro Enumeration .1.3.6.1.4.1.9.9.661.1.2.6.1.1.4 |
c3gCdma1xRttBandClassTableCellular 3G CDMA 1xRTT band class table. This table contains
band class information for each available band. SEQUENCE OF C3gCdma1xRttBandClassEntry .1.3.6.1.4.1.9.9.661.1.2.6.2 |
c3gCdma1xRttBandClassEntryAn entry (conceptual row) in the c3gCdma1xRttBandClassTable. C3gCdma1xRttBandClassEntry .1.3.6.1.4.1.9.9.661.1.2.6.2.1 |
c3gBandClassIndexBand class index, combined with entPhysicalIndex to access
the band class table. Integer32 .1.3.6.1.4.1.9.9.661.1.2.6.2.1.1 |
c3g1xRttBandClassThis object contains 1xRTT band class.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.2.1.2 |
c3gCdmaEvDoRadioTableCellular 3G CDMA EV-DO radio table. SEQUENCE OF C3gCdmaEvDoRadioEntry .1.3.6.1.4.1.9.9.661.1.2.6.3 |
c3gCdmaEvDoRadioEntryAn entry (conceptual row) in the c3gCdmaEvDoRadioTable. C3gCdmaEvDoRadioEntry .1.3.6.1.4.1.9.9.661.1.2.6.3.1 |
c3gCurrentEvDoRssiCurrent EV-DO RSSI value.ro C3gRssi .1.3.6.1.4.1.9.9.661.1.2.6.3.1.1 |
c3gCurrentEvDoEcIoCurrent EV-DO Ec/Io value.ro C3gEcIo .1.3.6.1.4.1.9.9.661.1.2.6.3.1.2 |
c3gCurrentEvDoChannelNumberCurrent EV-DO channel number. Current channel number to
which the modem is attached to the base station. Value of '-1'
indicates 'No Service'.ro Integer32 .1.3.6.1.4.1.9.9.661.1.2.6.3.1.3 |
c3gSectorIdSector ID of the base station to which the modem is attached.ro DisplayString .1.3.6.1.4.1.9.9.661.1.2.6.3.1.4 |
c3gSubnetMaskSubnet mask of the sector, not to be confused with the IP
subnet mask.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.3.1.5 |
c3gHdrColorCodeColor code of the sector.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.3.1.6 |
c3gPnOffsetPN offset. PN offset is a time offset from the beginning of
the well-known pseudo-random noise sequence that is used to
spread the signal from the base station.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.3.1.7 |
c3gRxMainGainControlReceived main gain control for the modem. value of '-1'
indicates the received main gain control is unavailable.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.2.6.3.1.8 |
c3gRxDiversityGainControlReceived diversity for the modem. value of '-1' indicates the
received diversity is unavailable.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.2.6.3.1.9 |
c3gTxTotalPowerTransmit total power.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.2.6.3.1.10 |
c3gTxGainAdjustTransmit gain adjust.ro Integer32 UNITS "dBm" .1.3.6.1.4.1.9.9.661.1.2.6.3.1.11 |
c3gCarrierToInterferenceRatioCarrier to interference ratio. Carrier-to-Interference
ratio (C/I) is the ratio of power in an RF carrier to the
interference power in the channel.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.3.1.12 |
c3gCdmaEvDoBandClassTableCellular 3G CDMA EV-DO band class table. This table contains
band class information for each available band. SEQUENCE OF C3gCdmaEvDoBandClassEntry .1.3.6.1.4.1.9.9.661.1.2.6.4 |
c3gCdmaEvDoBandClassEntryAn entry (conceptual row) in the c3gCdmaEvDoBandClassTable. C3gCdmaEvDoBandClassEntry .1.3.6.1.4.1.9.9.661.1.2.6.4.1 |
c3gEvDoBandClassThis object contains EV-DO band class.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.2.6.4.1.1 |
c3gCdmaHistoryTableCellular 3G CDMA history table. The history of RSSI are
carried in an octet of string. Each octet in the octet string
has a value from 0 to 150 and the 255 value is reserved to
indicate an uninitialized (Invalid) value. The format of the
octet string with n octets is as following:
[ octet 0 is latest,
octet 1 is latest-1,
.
.
octet n-2 is oldest-1,
octet n-1 is oldest ]
To convert the provided value into dBm the following formula
should be used:
dBm = (-1)*value; SEQUENCE OF C3gCdmaHistoryEntry .1.3.6.1.4.1.9.9.661.1.2.6.5 |
c3gCdmaHistoryEntryAn entry (conceptual row) in the c3gCdmaHistoryTable. C3gCdmaHistoryEntry .1.3.6.1.4.1.9.9.661.1.2.6.5.1 |
c3gCdmaHistory1xRttRssiPerSecondPer-second 1xRTT RSSI history. This object contains a
per-second history of 1xRTT RSSI values for the last 60
seconds.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.1 |
c3gCdmaHistory1xRttRssiPerMinutePer-minute 1xRTT weakest RSSI value history. This
object contains a per-minute history of 1xRTT weakest RSSI
values for the last 60 minutes. The octet in the string
is the weakest RSSI value measured in a minute interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.2 |
c3gCdmaHistory1xRttRssiPerHourPer-hour 1xRTT weakest RSSI value history. This object
contains a per-hour history of 1xRTT weakest RSSI values for the
last 72 hours. The octet in the string is the weakest RSSI
value measured in an hour interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.3 |
c3gCdmaHistoryEvDoRssiPerSecondPer-second EV-DO RSSI history. This object contains a
per-second history of EV-DO RSSI values for the last 60
seconds.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.4 |
c3gCdmaHistoryEvDoRssiPerMinutePer-minute EV-DO weakest RSSI value history. This
object contains a per-minute history of EV-DO weakest RSSI
values for the last 60 minutes. The octet in the string is the
weakest RSSI value measured in a minute interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.5 |
c3gCdmaHistoryEvDoRssiPerHourPer-hour EV-DO weakest RSSI value history. This object
contains a per-hour history of EV-DO weakest RSSI values for the
last 72 hours. The octet in the string is the weakest RSSI
value measured in an hour interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.2.6.5.1.6 |
c3gCdmaSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.2.7 |
c3gCdmaSecurityTableCellular 3G CDMA security table. SEQUENCE OF C3gCdmaSecurityEntry .1.3.6.1.4.1.9.9.661.1.2.7.1 |
c3gCdmaSecurityEntryAn entry (conceptual row) in the c3gCdmaSecurityTable. C3gCdmaSecurityEntry .1.3.6.1.4.1.9.9.661.1.2.7.1.1 |
c3gCdmaPinSecurityStatusCDMA Personal Identification Number (PIN) security:
unknown(1) - PIN security unknown
locked(2) - PIN security is locked
unlocked(3) - PIN security is unlockedrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.7.1.1.1 |
c3gCdmaPowerUpLockStatusCDMA power up lock:
unknown(1) - power up lock unknown
enabled(2) - power up lock enabled
disabled(3) - power up lock disabledrw Enumeration .1.3.6.1.4.1.9.9.661.1.2.7.1.1.2 |
c3gWanGsm OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.3 |
c3gGsmIdentityTable. SEQUENCE OF C3gGsmIdentityEntry .1.3.6.1.4.1.9.9.661.1.3.1 |
c3gGsmIdentityEntryAn entry (conceptual row) in the c3gGsmIdentityTable. C3gGsmIdentityEntry .1.3.6.1.4.1.9.9.661.1.3.1.1 |
c3gImsiInternational Mobile Subscriber Identifier (IMSI), a unique
15-digit code used to identify an individual user on a GSM/LTE
network.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.1.1.1 |
c3gImeiInternational Mobile Equipment Identifier (IMEI), a unique 15
or 17 digit code used to identify an individual mobile station
to a GSM, UMTS or LTE network.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.1.1.2 |
c3gIccIdThis object indicates the Integrated Circuit Card ID (ICCID).
The ICCID is defined by the ITU-T recommendation E.118.
ICCIDs are stored in the SIM cards and are also engraved or
printed on the SIM card body during a process called
personalization.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.1.1.3 |
c3gMsisdnThis object indicates the Mobile Subscriber Integrated Services
Digital Network Number (MSISDN). It is a number uniquely
identifying a subscription in a GSM, UMTS or LTE mobile
network. It represents the telephone number to the SIM
card in a mobile/cellular phone.rw DisplayString .1.3.6.1.4.1.9.9.661.1.3.1.1.4 |
c3gFsnForward Sequence Number (FSN), a message acknowledgement
method using sequence number in the forward direction.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.1.1.5 |
c3gModemStatusModem status:
unknown(1) - modem status is unknown
offLine(2) - modem is off line
onLine(3) - modem is on line
lowPowerMode(4) - modem is in the low power modero Enumeration .1.3.6.1.4.1.9.9.661.1.3.1.1.6 |
c3gGsmRoamingPreferenceThis object indicates the roaming preference.rw Enumeration .1.3.6.1.4.1.9.9.661.1.3.1.1.7 |
c3gGsmNetworkTableCellular GSM Network table. This table is applicable in both
3G and 4G-LTE technology mode SEQUENCE OF C3gGsmNetworkEntry .1.3.6.1.4.1.9.9.661.1.3.2 |
c3gGsmNetworkEntryAn entry (conceptual row) in the c3gGsmNetworkTable. C3gGsmNetworkEntry .1.3.6.1.4.1.9.9.661.1.3.2.1 |
c3gGsmLacLocation Area Code (LAC), also called as Tracking
Area Code (TAC) in LTE standard. LAC/TAC is given
by the base station.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.2.1.1 |
c3gGsmCurrentServiceStatusCurrent Service Status:
unknown(1) - current service status is unknown
noService(2) - no service
normal(3) - service status is normal
emergencyOnly(4) - emergency service onlyro Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.2 |
c3gGsmCurrentServiceErrorCurrent service error:
unknown(1) - Unknown
none(2) - None
imsiUnknownInHlr(3) - IMSI unknown in HLR (Home
Location Register)
illegalMs(4) - Illegal MS (Mobile Station)
imsiUnknownInVlr(5) - IMSI unknown in VLR (Visitor
Location Register)
imeiNotAccepted(6) - IMEI not accepted
illegalMe(7) - Illegal ME (Mobile Entity)
gprsServNotAllowed(8) - GPRS services not allowed
gprsNonGprsServNotAllow(9) - GPRS and non-GPRS services
not allowed
msIdentUnknown(10) - MS identity unknown
implicitlyDetached(11) - Implicitly detached
plmnNotAllowed(12) - PLMN not allowed
lacNotAllowed(13) - LAC not allowed
roamingNotAllowed(14) - Roaming not allowed
gprsServNotAllowInPlmn(15) - GPRS services not allowed
in this PLMN
noSuitableCellInLa(16) - No suitable cells in LA (Location
Area)
mscTempNotReachable(17) - MSC (Mobile Switching Center)
temporarily not reachable
networkFailure(18) - Network failure
macFailure(19) - MAC failure
synchFailure(20) - Synch failure
congestion(21) - Congestion
gsmAuthenNotAccept(22) - GSM/LTE Authentication not accepted
servOptionNotSupport(23) - Service option not supported
reqServOptionNotSub(24) - Requested service option not
subscribed
servOptionOutOfOrder(25) - Service option out of order
callCannotIdentified(26) - Call cannot be identified
noPdpContextActivated(27) - No PDP context activated
invalidMandatInfo(28) - Invalid mandatory info
unpsecProtErr(29) - Unspecified protocol errorro Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.3 |
c3gGsmCurrentServiceCurrent service type:
unknown(1) - service type is unknown
invalid(2) - no service
circuitSwitched(3) - circuit switched service
packetSwitched(4) - packet switched service
combined(5) - combination of circuit and packet
switched servicero Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.4 |
c3gGsmPacketServicePacket Service type:
unknown(1) - service type is unknown.
none(2) - no service.
gprs(3) - General Packet Radio Service (GPRS).
edge(4) - Enhanced Data rates for GSM Evolution (EDGE).
umtsWcdma(5) - Universal Mobile Telecommunications
System (UMTS) / Wideband Code-Division
Multiple-Access (W-CDMA).
hsdpa(6) - High-Speed Downlink Packet Access (HSDPA)
hsdpa(7) - High-Speed Uplink Packet Access (HSUPA)
hspa(8) - High-Speed Packet Access (HSPA)
hspaPlus(9) - High-Speed Packet Access (HSPA) Plus
lte(10) - Long Term Evolutionro Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.5 |
c3gGsmCurrentRoamingStatusThis object indicates whether the modem is in the home network
or is roaming.ro Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.6 |
c3gGsmNetworkSelectionModeNetwork selection mode. Can be manual selection mode or
automatic selection mode. Set to automatic by default.rw Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.7 |
c3gGsmCountryCountry code. Country code string is given by the base
station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.2.1.8 |
c3gGsmNetworkNetwork code. Network Code string is given by the base
station.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.2.1.9 |
c3gGsmMccMobile Country Code (MCC). Value of '-1' indicates MCC is 'Not
Applicable'.rw Integer32 .1.3.6.1.4.1.9.9.661.1.3.2.1.10 |
c3gGsmMncMobile Network Code (MNC). Value of '-1' indicates MNC is 'Not
Applicable'.rw Integer32 .1.3.6.1.4.1.9.9.661.1.3.2.1.11 |
c3gGsmRacRouting Area Code (RAC). RAC is given by the base station.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.2.1.12 |
c3gGsmCurrentCellIdCell Identifier of current cell. Cell ID is given by the
base station.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.2.1.13 |
c3gGsmCurrentPrimaryScramblingCodePrimary scrambling code of current cell. The primary
scrambling code is typically identified through
symbol-by-symbol correlation over the CPICH (Common Pilot
Channel) with all codes within the code group, after the
primary scrambling code has been identified,
the Primary CCPCH can be detected and the system and cell
specific BCH information can be read.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.2.1.14 |
c3gGsmPlmnSelectionPublic Land Mobile Network (PLMN) selection. Can be manual
selection mode or automatic selection mode. Set to automatic by
default.rw Enumeration .1.3.6.1.4.1.9.9.661.1.3.2.1.15 |
c3gGsmRegPlmnRegistered PLMN.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.2.1.16 |
c3gGsmPlmnAbbrPLMN abbreviated number.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.2.1.17 |
c3gGsmServiceProviderService provider.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.2.1.18 |
c3gGsmTotalByteTransmittedTotal number of bytes transmitted for all calls. It is the
total number of bytes transmitted by modem, not to be confused
with the number of bytes transmitted through the interface.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.3.2.1.19 |
c3gGsmTotalByteReceivedTotal number of bytes received for all calls. It is the total
number of bytes received by modem, not to be confused with the
number of bytes received from the interface.ro Counter64 UNITS "bytes" .1.3.6.1.4.1.9.9.661.1.3.2.1.20 |
c3gGsmPdpProfile OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.3.3 |
c3gGsmPdpProfileTableCellular GSM PDP profiles table. Cellular device contains
multiple profile entries which can be used to establish
cellular data connections (PDP contexts). Users can choose
any of available PDP profiles to establish data connections.
Data connections are described in c3gGsmPacketSessionTable.
This table is applicable in only 3G technology mode. Refer
CISCO-WAN-CELL-EXT-MIB when in 4G-LTE mode. SEQUENCE OF C3gGsmPdpProfileEntry .1.3.6.1.4.1.9.9.661.1.3.3.1 |
c3gGsmPdpProfileEntryAn entry (conceptual row) in the c3gGsmPdpProfileTable. C3gGsmPdpProfileEntry .1.3.6.1.4.1.9.9.661.1.3.3.1.1 |
c3gGsmPdpProfileIndexProfile index, combined with entPhysicalIndex to
access profile table. Integer32 .1.3.6.1.4.1.9.9.661.1.3.3.1.1.1 |
c3gGsmPdpProfileTypeThis object indicates configured Packet Data Protocol (PDP)
type.rw C3gPdpType .1.3.6.1.4.1.9.9.661.1.3.3.1.1.2 |
c3gGsmPdpProfileAddrConfigured PDP/EPS Bearer address. PDP type is
defined in c3gGsmPdpProfileType.rw DisplayString .1.3.6.1.4.1.9.9.661.1.3.3.1.1.3 |
c3gGsmPdpProfileApnThis object indicates profile Access Point Name (APN). This
information is provided by the service provider.rw DisplayString .1.3.6.1.4.1.9.9.661.1.3.3.1.1.4 |
c3gGsmPdpProfileAuthenTypeThis object indicates PDP authentication type
supported. CHAP and PAP are supported in GSM. The type of
authentication to be used is provided by the service
provider.rw Enumeration .1.3.6.1.4.1.9.9.661.1.3.3.1.1.5 |
c3gGsmPdpProfileUsernameThis object indicates the username to be used for PDP
authentication. This information is provided by the service
provider.rw DisplayString .1.3.6.1.4.1.9.9.661.1.3.3.1.1.6 |
c3gGsmPdpProfilePasswordThis object indicates the password to be used for PDP
authentication. This information is provided by the service
provider.rw DisplayString .1.3.6.1.4.1.9.9.661.1.3.3.1.1.7 |
c3gGsmPdpProfileRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.3.3.1.1.8 |
c3gGsmPacketSessionTableCellular 3G GSM packet session table. This table is applicable
in only 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
when in 4G-LTE mode. SEQUENCE OF C3gGsmPacketSessionEntry .1.3.6.1.4.1.9.9.661.1.3.3.2 |
c3gGsmPacketSessionEntryAn entry (conceptual row) in the c3gGsmPacketSessionTable. C3gGsmPacketSessionEntry .1.3.6.1.4.1.9.9.661.1.3.3.2.1 |
c3gGsmPacketSessionStatusThis object indicates PDP session status
of the profile. This is active when the call is established
and PDP contextr has become active.ro Enumeration .1.3.6.1.4.1.9.9.661.1.3.3.2.1.1 |
c3gGsmPdpTypeThis object indicates current session PDP type.ro C3gPdpType .1.3.6.1.4.1.9.9.661.1.3.3.2.1.2 |
c3gGsmPdpAddressCurrent session PDP context/EPS Bearer address. PDP type is
obtained from c3gGsmPdpType.ro DisplayString .1.3.6.1.4.1.9.9.661.1.3.3.2.1.3 |
c3gGsmReqUmtsQosTableRequested UMTS QoS parameters table. This table contains UMTS
QoS parameters requested by modem to the cellular network
via PDP Context Activation Request message. The requested UMTS
QoS profile is optional. This table is applicable only in 3G
technology mode. SEQUENCE OF C3gGsmReqUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.3 |
c3gGsmReqUmtsQosEntryAn entry (conceptual row) in the c3gGsmReqUmtsQosTable. C3gGsmReqUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.3.1 |
c3gGsmReqUmtsQosTrafficClassRequest UMTS QoS traffic classes.rw C3gUmtsQosTrafficClass .1.3.6.1.4.1.9.9.661.1.3.3.3.1.2 |
c3gGsmReqUmtsQosMaxUpLinkBitRateRequest UMTS QoS maximum uplink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.3.1.3 |
c3gGsmReqUmtsQosMaxDownLinkBitRateRequest UMTS QoS maximum downlink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.3.1.4 |
c3gGsmReqUmtsQosGuaUpLinkBitRateRequest UMTS QoS guaranteed uplink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.3.1.5 |
c3gGsmReqUmtsQosGuaDownLinkBitRateRequest UMTS QoS guaranteed downlink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.3.1.6 |
c3gGsmReqUmtsQosOrderRequest UMTS QoS deliver order.rw C3gUmtsQosOrder .1.3.6.1.4.1.9.9.661.1.3.3.3.1.7 |
c3gGsmReqUmtsQosErroneousSduRequest UMTS QoS Delivery of Erroneous SDU.rw C3gUmtsQosErroneousSdu .1.3.6.1.4.1.9.9.661.1.3.3.3.1.8 |
c3gGsmReqUmtsQosMaxSduSizeRequest UMTS QoS maximum SDU size, the valid range is between 1
and 1520 bytes. Value of '0' indicates the maximum SDU size is
unspecified.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.3.1.9 |
c3gGsmReqUmtsQosSerRequest UMTS QoS SDU error ratio.rw C3gUmtsQosSer .1.3.6.1.4.1.9.9.661.1.3.3.3.1.10 |
c3gGsmReqUmtsQosBerRequest UMTS QoS residual bit error ratio.rw C3gUmtsQosBer .1.3.6.1.4.1.9.9.661.1.3.3.3.1.11 |
c3gGsmReqUmtsQosDelayRequest UMTS QoS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is unspecified.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.3.1.12 |
c3gGsmReqUmtsQosPriorityRequest UMTS QoS traffic handling priority.rw C3gUmtsQosPriority .1.3.6.1.4.1.9.9.661.1.3.3.3.1.13 |
c3gGsmReqUmtsQosSrcStatDescriptorRequest UMTS QoS source statistics descriptor.rw C3gUmtsQosSrcStatDescriptor .1.3.6.1.4.1.9.9.661.1.3.3.3.1.14 |
c3gGsmReqUmtsQosSignalIndicationRequest UMTS QoS signalling indication.rw C3gUmtsQosSignalIndication .1.3.6.1.4.1.9.9.661.1.3.3.3.1.15 |
c3gGsmReqUmtsQosRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.3.3.3.1.16 |
c3gGsmMinUmtsQosTableMinimum acceptable UMTS QoS table. This table contains minimum
acceptable UMTS QoS parameters which is checked by the MT
(Mobile Termination) against the negotiated profile returned in
the Activate PDP Context Accept message. The minimum acceptable
UMTS QoS profile is optional. This table is applicable only in
3G technology mode. SEQUENCE OF C3gGsmMinUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.4 |
c3gGsmMinUmtsQosEntryAn entry (conceptual row) in the c3gGsmMinUmtsQosTable. C3gGsmMinUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.4.1 |
c3gGsmMinUmtsQosTrafficClassMinimum UMTS QoS traffic classes.rw C3gUmtsQosTrafficClass .1.3.6.1.4.1.9.9.661.1.3.3.4.1.1 |
c3gGsmMinUmtsQosMaxUpLinkBitRateMinimum UMTS QoS maximum uplink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.4.1.2 |
c3gGsmMinUmtsQosMaxDownLinkBitRateMinimum UMTS QoS maximum downlink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.4.1.3 |
c3gGsmMinUmtsQosGuaUpLinkBitRateMinimum UMTS QoS guaranteed uplink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.4.1.4 |
c3gGsmMinUmtsQosGuaDownLinkBitRateMinimum UMTS QoS guaranteed downlink bit rate.rw C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.4.1.5 |
c3gGsmMinUmtsQosOrderMinimum UMTS QoS deliver order.rw C3gUmtsQosOrder .1.3.6.1.4.1.9.9.661.1.3.3.4.1.6 |
c3gGsmMinUmtsQosErroneousSduMinimum UMTS QoS Delivery of Erroneous SDU.rw C3gUmtsQosErroneousSdu .1.3.6.1.4.1.9.9.661.1.3.3.4.1.7 |
c3gGsmMinUmtsQosMaxSduSizeMinimum UMTS maximum SDU size, the valid range is between 1 and
1520 bytes. Value of '0' indicates the maximum SDU size is
unspecified.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.4.1.8 |
c3gGsmMinUmtsQosSerMinimum UMTS QoS SDU error ratio.rw C3gUmtsQosSer .1.3.6.1.4.1.9.9.661.1.3.3.4.1.9 |
c3gGsmMinUmtsQosBerMinimum UMTS residual bit error ratio.rw C3gUmtsQosBer .1.3.6.1.4.1.9.9.661.1.3.3.4.1.10 |
c3gGsmMinUmtsQosDelayMinimum UMTS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is unspecified.rw Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.4.1.11 |
c3gGsmMinUmtsQosPriorityMinimum UMTS QoS traffic handling priority.rw C3gUmtsQosPriority .1.3.6.1.4.1.9.9.661.1.3.3.4.1.12 |
c3gGsmMinUmtsQosSrcStatDescriptorMinimum UMTS QoS source statistics descriptor.rw C3gUmtsQosSrcStatDescriptor .1.3.6.1.4.1.9.9.661.1.3.3.4.1.13 |
c3gGsmMinUmtsQosSignalIndicationMinimum UMTS QoS signalling indication.rw C3gUmtsQosSignalIndication .1.3.6.1.4.1.9.9.661.1.3.3.4.1.14 |
c3gGsmMinUmtsQosRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.3.3.4.1.15 |
c3gGsmNegoUmtsQosTableNegotiated UMTS QoS table. This table contains negotiated UMTS
QoS parameters returned in the Activate PDP Context Accept
message. The objects in this table are valid only if the value
of object c3gGsmPacketSessionStatus defined in
c3gGsmPacketSessionTable is 'active'. This table is applicable
only in 3G technology mode. SEQUENCE OF C3gGsmNegoUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.5 |
c3gGsmNegoUmtsQosEntryAn entry (conceptual row) in the c3gGsmNegoUmtsQosTable. C3gGsmNegoUmtsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.5.1 |
c3gGsmNegoUmtsQosTrafficClassNegotiated UMTS QoS traffic classes.ro C3gUmtsQosTrafficClass .1.3.6.1.4.1.9.9.661.1.3.3.5.1.1 |
c3gGsmNegoUmtsQosMaxUpLinkBitRateNegotiated UMTS QoS maximum uplink bit rate.ro C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.5.1.2 |
c3gGsmNegoUmtsQosMaxDownLinkBitRateNegotiated UMTS QoS maximum downlink bit rate.ro C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.5.1.3 |
c3gGsmNegoUmtsQosGuaUpLinkBitRateNegotiated UMTS QoS guaranteed uplink bit rate.ro C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.5.1.4 |
c3gGsmNegoUmtsQosGuaDownLinkBitRateNegotiated UMTS QoS guaranteed downlink bit rate.ro C3gUmtsQosLinkBitRate .1.3.6.1.4.1.9.9.661.1.3.3.5.1.5 |
c3gGsmNegoUmtsQosOrderNegotiated UMTS QoS deliver order.ro C3gUmtsQosOrder .1.3.6.1.4.1.9.9.661.1.3.3.5.1.6 |
c3gGsmNegoUmtsQosErroneousSduNegotiated UMTS QoS Delivery of Erroneous SDU.ro C3gUmtsQosErroneousSdu .1.3.6.1.4.1.9.9.661.1.3.3.5.1.7 |
c3gGsmNegoUmtsQosMaxSduSizeNegotiated UMTS QoS maximum SDU size, the valid range is
between 1 and 1520 bytes. Value of '0' indicates the maximum
SDU size is subscribed.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.5.1.8 |
c3gGsmNegoUmtsQosSerNegotiated UMTS QoS SDU error ratio.ro C3gUmtsQosSer .1.3.6.1.4.1.9.9.661.1.3.3.5.1.9 |
c3gGsmNegoUmtsQosBerNegotiated UMTS QoS residual bit error ratio.ro C3gUmtsQosBer .1.3.6.1.4.1.9.9.661.1.3.3.5.1.10 |
c3gGsmNegoUmtsQosDelayNegotiated UMTS QoS transfer delay in ms, the valid range
is between 1 and 4000 ms. Value of '0' indicates the
QoS delay is subscribed.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.3.5.1.11 |
c3gGsmNegoUmtsQosPriorityNegotiated UMTS QoS traffic handling priority.ro C3gUmtsQosPriority .1.3.6.1.4.1.9.9.661.1.3.3.5.1.12 |
c3gGsmNegoUmtsQosSrcStatDescriptorNegotiated UMTS QoS source statistics descriptor.ro C3gUmtsQosSrcStatDescriptor .1.3.6.1.4.1.9.9.661.1.3.3.5.1.13 |
c3gGsmNegoUmtsQosSignalIndicationNegotiated UMTS QoS signalling indication.ro C3gUmtsQosSignalIndication .1.3.6.1.4.1.9.9.661.1.3.3.5.1.14 |
c3gGsmReqGprsQosTableRequested GPRS QoS parameters table. This table contains GPRS
QoS parameters requested by modem to the cellular network
via PDP Context Request message. The requested GPRS QoS
profile is optional. This table is applicable only in
3G technology mode. SEQUENCE OF C3gGsmReqGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.6 |
c3gGsmReqGprsQosEntryAn entry (conceptual row) in the c3gGsmReqGprsQosTable. C3gGsmReqGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.6.1 |
c3gGsmReqGprsQosPrecedenceRequest GPRS QoS precedence.rw C3gGprsQosPrecedence .1.3.6.1.4.1.9.9.661.1.3.3.6.1.1 |
c3gGsmReqGprsQosDelayRequest GPRS QoS delay classes.rw C3gGprsQosDelay .1.3.6.1.4.1.9.9.661.1.3.3.6.1.2 |
c3gGsmReqGprsQosReliabilityRequest GPRS QoS reliability.rw C3gGprsQosReliability .1.3.6.1.4.1.9.9.661.1.3.3.6.1.3 |
c3gGsmReqGprsQosPeakRateRequest GPRS QoS peak rate.rw C3gGprsQosPeakRate .1.3.6.1.4.1.9.9.661.1.3.3.6.1.4 |
c3gGsmReqGprsQosMeanRateRequest GPRS QoS mean rate.rw C3gGprsQosMeanRate UNITS "octet-per-hour" .1.3.6.1.4.1.9.9.661.1.3.3.6.1.5 |
c3gGsmReqGprsQosRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.3.3.6.1.6 |
c3gGsmMinGprsQosTableMinimum acceptable GPRS QoS table. This table contains minimum
acceptable GPRS QoS parameters which is checked by the MT
(Mobile Termination) against the negotiated profile returned in
the Activate PDP Context Accept message. The minimum acceptable
GPRS QoS profile is optional. This table is applicable only in
3G technology mode. SEQUENCE OF C3gGsmMinGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.7 |
c3gGsmMinGprsQosEntryAn entry (conceptual row) in the c3gGsmMinGprsQosTable. C3gGsmMinGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.7.1 |
c3gGsmMinGprsQosPrecedenceMinimum GPRS QoS precedence.rw C3gGprsQosPrecedence .1.3.6.1.4.1.9.9.661.1.3.3.7.1.1 |
c3gGsmMinGprsQosDelayMinimum GPRS QoS delay classes.rw C3gGprsQosDelay .1.3.6.1.4.1.9.9.661.1.3.3.7.1.2 |
c3gGsmMinGprsQosReliabilityMinimum GPRS QoS reliability.rw C3gGprsQosReliability .1.3.6.1.4.1.9.9.661.1.3.3.7.1.3 |
c3gGsmMinGprsQosPeakRateMinimum GPRS QoS peak rate.rw C3gGprsQosPeakRate .1.3.6.1.4.1.9.9.661.1.3.3.7.1.4 |
c3gGsmMinGprsQosMeanRateMinimum GPRS QoS mean rate.rw C3gGprsQosMeanRate UNITS "octet-per-hour" .1.3.6.1.4.1.9.9.661.1.3.3.7.1.5 |
c3gGsmMinGprsQosRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.3.3.7.1.6 |
c3gGsmNegoGprsQosTableNegotiated GPRS QoS table. This table contains negotiated GPRS
QoS parameters returned in the Activate PDP Context Accept
message. The objects in this table are valid only if the value
of object c3gGsmPacketSessionStatus defined in
c3gGsmPacketSessionTable is 'active'. This table is applicable
only in 3G technology mode. SEQUENCE OF C3gGsmNegoGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.8 |
c3gGsmNegoGprsQosEntryAn entry (conceptual row) in the c3gGsmNegoGprsQosTable. C3gGsmNegoGprsQosEntry .1.3.6.1.4.1.9.9.661.1.3.3.8.1 |
c3gGsmNegoGprsQosPrecedenceNegotiated GPRS QoS precedence.ro C3gGprsQosPrecedence .1.3.6.1.4.1.9.9.661.1.3.3.8.1.1 |
c3gGsmNegoGprsQosDelayNegotiated GPRS QoS delay classes.ro C3gGprsQosDelay .1.3.6.1.4.1.9.9.661.1.3.3.8.1.2 |
c3gGsmNegoGprsQosReliabilityNegotiated GPRS QoS reliability.ro C3gGprsQosReliability .1.3.6.1.4.1.9.9.661.1.3.3.8.1.3 |
c3gGsmNegoGprsQosPeakRateNegotiated GPRS QoS peak rate.ro C3gGprsQosPeakRate .1.3.6.1.4.1.9.9.661.1.3.3.8.1.4 |
c3gGsmNegoGprsQosMeanRateNegotiated GPRS QoS mean rate.ro C3gGprsQosMeanRate UNITS "octet-per-hour" .1.3.6.1.4.1.9.9.661.1.3.3.8.1.5 |
c3gGsmRadio OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.3.4 |
c3gGsmRadioTableCellular 3G GSM/4G-LTE radio table. SEQUENCE OF C3gGsmRadioEntry .1.3.6.1.4.1.9.9.661.1.3.4.1 |
c3gGsmRadioEntryAn entry (conceptual row) in the c3gGsmRadioTable. C3gGsmRadioEntry .1.3.6.1.4.1.9.9.661.1.3.4.1.1 |
c3gCurrentGsmRssiThe GPRS/UMTS/LTE RSSI value.ro C3gRssi .1.3.6.1.4.1.9.9.661.1.3.4.1.1.1 |
c3gCurrentGsmEcIoThe GPRS, UMTS or LTE Ec/Io value.ro C3gEcIo .1.3.6.1.4.1.9.9.661.1.3.4.1.1.2 |
c3gGsmCurrentBandGPRS/UMTS/LTE band to which the modem is attached.
Refer CISCO-WAN-CELL-EXT-MIB for LTE band number when
in LTE mode.ro Enumeration .1.3.6.1.4.1.9.9.661.1.3.4.1.1.3 |
c3gGsmChannelNumberChannel number to which the modem is attached. This is only
applicable in 3G technology mode. Refer CISCO-WAN-CELL-EXT-MIB
for the LTE uplink and downlink channel valuesro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.4.1.1.4 |
c3gGsmNumberOfNearbyCellThis object indicates the current total number of
nearby cell in the c3gGsmNearbyCellTable. User can
poll this object to get the total number of nearby
cell before polling c3gGsmNearbyCellTable.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.4.1.1.5 |
c3gGsmNearbyCellTableCellular GSM/4G-LTE nearby cell table. Object
c3gGsmNumberOfNearbyCell indicates the total
number of nearby cell in this table. SEQUENCE OF C3gGsmNearbyCellEntry .1.3.6.1.4.1.9.9.661.1.3.4.2 |
c3gGsmNearbyCellEntryAn entry (conceptual row) in the c3gGsmNearbyCellTable. C3gGsmNearbyCellEntry .1.3.6.1.4.1.9.9.661.1.3.4.2.1 |
c3gGsmNearbyCellIndexNearby cell index, combined with entPhysicalIndex to access
the Nearby cell table c3gGsmNearbyCellTable. Integer32 .1.3.6.1.4.1.9.9.661.1.3.4.2.1.1 |
c3gGsmNearbyCellPrimaryScramblingCodeNearby cell primary scrambling code.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.4.2.1.2 |
c3gGsmNearbyCellRscpNearby cell Received Signal Code Power (RSCP).ro Integer32 (-150..0) UNITS "dB" .1.3.6.1.4.1.9.9.661.1.3.4.2.1.3 |
c3gGsmNearbyCellEcIoMeasurementNearby cell Ec/Io measurement.ro C3gEcIo UNITS "dB" .1.3.6.1.4.1.9.9.661.1.3.4.2.1.4 |
c3gGsmHistoryTableCellular 3G GSM/4G-LTE RSSI history table. The history of RSSI
are carried in an octet of string. Each octet in the octet
string has a value from 0 to 150 and the 255 value is reserved
to indicate an uninitialized (Invalid) value. The format of
the octet string with n octets is as following:
[ octet 0 is latest,
octet 1 is latest-1,
.
.
octet n-2 is oldest-1,
octet n-1 is oldest ]
To convert the provided value into dBm the following formula
should be used:
dBm = (-1)*value; SEQUENCE OF C3gGsmHistoryEntry .1.3.6.1.4.1.9.9.661.1.3.4.3 |
c3gGsmHistoryEntryAn entry (conceptual row) in the c3gGsmHistoryTable. C3gGsmHistoryEntry .1.3.6.1.4.1.9.9.661.1.3.4.3.1 |
c3gGsmHistoryRssiPerSecondPer-second RSSI history. This object contains a
per-second history of RSSI values for the last 60 seconds.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.3.4.3.1.1 |
c3gGsmHistoryRssiPerMinutePer-minute weakest RSSI value history. This object
contains a per-minute history of weakest RSSI values for the
last 60 minutes. The octet in the string is the weakest RSSI
value measured in a minute interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.3.4.3.1.2 |
c3gGsmHistoryRssiPerHourPer-hour weakest RSSI value history. This object
contains a per-hour history of weakest RSSI values for the last
72 hours. The octet in the string is the weakest RSSI value
measured in an hour interval.ro OCTET STRING .1.3.6.1.4.1.9.9.661.1.3.4.3.1.3 |
c3gGsmSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.3.5 |
c3gGsmSecurityTableCellular 3G GSM/4G-LTE security table. SEQUENCE OF C3gGsmSecurityEntry .1.3.6.1.4.1.9.9.661.1.3.5.1 |
c3gGsmSecurityEntryAn entry (conceptual row) in the c3gGsmSecurityTable. C3gGsmSecurityEntry .1.3.6.1.4.1.9.9.661.1.3.5.1.1 |
c3gGsmChv1Card Holder Verification 1 (CHV1), if enabled, the PIN will be
verified, if disabled, the PIN will not be verified.rw Enumeration .1.3.6.1.4.1.9.9.661.1.3.5.1.1.1 |
c3gGsmSimStatusSIM status. Indicates whether the SIM is present or removed
from the SIM socket, and its current status.ro Enumeration .1.3.6.1.4.1.9.9.661.1.3.5.1.1.2 |
c3gGsmSimUserOperationRequiredIf the SIM is protected (for example, because of CHV1 enabled),
it will indicate the type of user operation required.ro Enumeration .1.3.6.1.4.1.9.9.661.1.3.5.1.1.3 |
c3gGsmNumberOfRetriesRemainingIndicates the number of attempts remaining in case the SIM is
locked. If the number of retries becomes zero, the SIM is
blocked and becomes unusable.ro Unsigned32 .1.3.6.1.4.1.9.9.661.1.3.5.1.1.4 |
c3gWanLbs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.4 |
c3gWanLbsCommon OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.4.1 |
c3gWanLbsCommonTableThis table contains information about the Cellular Location
Based service feature. This GPS data is provided by the wireless
modem upon GPS configuration. SEQUENCE OF C3gWanLbsCommonEntry .1.3.6.1.4.1.9.9.661.1.4.1.1 |
c3gWanLbsCommonEntryThis entry contains information about the
Cellular Location Based service
variables returned by the wireless modem. C3gWanLbsCommonEntry .1.3.6.1.4.1.9.9.661.1.4.1.1.1 |
c3gLbsModeSelectedMode of Location base service selected.
unKnown - mode selection unkown
standAlone - Standalone mode
msBased - MS-Based mode
msAssist - MS-Assist mode
reserved - reserved for future usero Enumeration .1.3.6.1.4.1.9.9.661.1.4.1.1.1.1 |
c3gLbsStateLocation base service state.
gpsDisabled - GPS is disabled
gpsEnabled - GPS is enabled
gpsLocError - GPS encounters error
gpsAcquiring - GPS is acquiring fixro Enumeration .1.3.6.1.4.1.9.9.661.1.4.1.1.1.2 |
c3gLbsLocFixErrorLocation base service fix error code.ro Enumeration .1.3.6.1.4.1.9.9.661.1.4.1.1.1.3 |
c3gLbsLatitudeLocation base service Latitude.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.661.1.4.1.1.1.4 |
c3gLbsLongitudeLocation base service longitude.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.661.1.4.1.1.1.5 |
c3gLbsTimeStampLocation base service timestamp.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.661.1.4.1.1.1.6 |
c3gLbsLocUncertaintyAngleGPS Uncertainty parameter Angle, in degrees
for the Uncertainty info returned by the GPS
device while doing a location fix.ro Unsigned32 UNITS "degrees" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.7 |
c3gLbsLocUncertaintyAGPS Uncertainty parameter A, value in meters
for the Uncertainty info returned by the GPS
device while doing a location fix.ro Unsigned32 UNITS "meters" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.8 |
c3gLbsLocUncertaintyPosGPS Uncertainty parameter position, value in meters
for the Uncertainty info returned by the GPS device
while doing a location fix.ro Unsigned32 UNITS "meters" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.9 |
c3gLbsFixtypeThe type of location fix in Location Base service.
none - default case, while LBS is not enabled.
twoDimension - 2D location fix.
threeDimension - 3D location fix.ro Enumeration .1.3.6.1.4.1.9.9.661.1.4.1.1.1.10 |
c3gLbsHeightValidThis object indicates whether the height returned by
the GPS device is valid during location fix.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.4.1.1.1.11 |
c3gLbsHeightThis object indicates the GPS height parameter returned
by the GPS device while performing location fix.ro Integer32 (-500..500) UNITS "meters" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.12 |
c3gLbsLocUncertaintyVerticalGPS parameter vertical velocity parameter returned by
the GPS device while performing location fix.ro Unsigned32 UNITS "meters" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.13 |
c3gLbsVelocityValidThis object indicates whether the Velocity value
returned by the GPS device is valid.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.4.1.1.1.14 |
c3gLbsHeadingThe compass direction toward which the GPS receiver
is (or should be) moving.ro Unsigned32 UNITS "degrees" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.15 |
c3gLbsVelocityHorizontalHorizontal Velocity in meters per second the GPS
device is heading. This is the value returned by
the GPS satellite relative to the last horizontal
location of the GPS device. If at Time X satellite
sees the location of GPS device is L1 and then at
Time Y satellite sees the location is L2 then
speed is (L2 - L1) / ( Y - X).ro Unsigned32 UNITS "meters per second" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.16 |
c3gLbsVelocityVerticalVertical Velocity in meters per second
the GPS device is heading. This is the value returned by
the GPS satellite relative to the last vertical location of
the GPS device. If at Time X satellite sees the location
of GPS device is L1 and then at Time Y satellite sees
the location is L2 then speed is (L2 - L1) / ( Y - X).ro Unsigned32 UNITS "meters per second" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.17 |
c3gLbsHepeHorizontal Estimated Position Error returned by the
GPS satellite for current position of the GPS device.ro Unsigned32 UNITS "centimeters" .1.3.6.1.4.1.9.9.661.1.4.1.1.1.18 |
c3gLbsNumSatellitesNumber of GPS satellites in vision to the modem
while GPS tracking is on.ro Gauge32 .1.3.6.1.4.1.9.9.661.1.4.1.1.1.19 |
c3gWanLbsSatelliteInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.4.2 |
c3gWanLbsSatelliteInfoTableThis table provides information on each satellite that is
visible to the modem during the location fix. These
satellites guide the device to acquire a 2D or 3D
location fix. SEQUENCE OF C3gWanLbsSatelliteInfoEntry .1.3.6.1.4.1.9.9.661.1.4.2.1 |
c3gWanLbsSatelliteInfoEntryThis table provides information about each satellite's
elevation, azimuth, Signal to Noise ratio (SNR) and
its reference number local to the router. C3gWanLbsSatelliteInfoEntry .1.3.6.1.4.1.9.9.661.1.4.2.1.1 |
c3gWanLbsSatelliteInfoIndexAn index that is assigned to each satellite under a modem
and in combination with entPhysicalIndex uniquely identify it.
This index is assigned arbitrarily by the engine and is not
saved over reboots. Integer32 .1.3.6.1.4.1.9.9.661.1.4.2.1.1.1 |
c3gWanLbsSatelliteNumberEach Satellite is assigned a unique number
within this device.This object can be used
to locate a particular satellite under
a modem.ro Integer32 .1.3.6.1.4.1.9.9.661.1.4.2.1.1.2 |
c3gWanLbsSatelliteElevationAngle of Elevation between the GPS antenna pointing direction,
directly towards the satellite, and the local horizontal plane.
It is the up-down anglero Integer32 UNITS "degrees" .1.3.6.1.4.1.9.9.661.1.4.2.1.1.3 |
c3gWanLbsSatelliteAzimuthAzimuth of the current satellite in context
referenced by the Satellite InfoIndex.
Azimuth is the degree of rotation of the
satellites dish on its vertical plane.ro Integer32 UNITS "degrees" .1.3.6.1.4.1.9.9.661.1.4.2.1.1.4 |
c3gWanLbsSatelliteInfoSignalNoiseRatioSignal to Noise Ratio(SNR) of received GPS signal.
SNR is refered to as the signal strength in
GPS standards.ro Integer32 UNITS "db" .1.3.6.1.4.1.9.9.661.1.4.2.1.1.5 |
c3gWanLbsSatelliteUsedIs this satellite in line of sight to the
modem used in calculating the GPS location?ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.4.2.1.1.6 |
c3gWanLbsSatelliteInfoRowStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.4.2.1.1.7 |
c3gWanSmsCommon OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.5 |
c3gWanSms OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.1.5.1 |
c3gSmsCommonTableThis table contains Cellular SMS management
MIB objects. SEQUENCE OF C3gSmsCommonEntry .1.3.6.1.4.1.9.9.661.1.5.1.1 |
c3gSmsCommonEntryAn entry contains counters for the SMS messages
received, placed, errored and archived on CDMA,
GSM or LTE based modems. C3gSmsCommonEntry .1.3.6.1.4.1.9.9.661.1.5.1.1.1 |
c3gSmsServiceAvailableThis object indicates the availability of SMS Service.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.661.1.5.1.1.1.1 |
c3gSmsOutSmsCountNumber of SMS messages which have been sent
successfully.ro Counter32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.2 |
c3gSmsOutSmsErrorCountNumber of SMS message that could not be sent.ro Counter32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.3 |
c3gSmsInSmsStorageUsedNumber of SMS message records space used in the
Incoming SMS message storage. One standard
SMS message (cdma or gsm) occupies 1 unit of
record storage space. A big SMS message can span
'n' sms record space but still be called as 1 SMS
message. Storage used can be greater than or equal
to total number of Incoming SMS received.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.4 |
c3gSmsInSmsStorageUnusedThe number of SMS messages record space left
unused in the Incoming SMS message storage.
This is equal to c3gSmsInSmsStorageMax -
c3gSmsInSmsStorageUsed.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.5 |
c3gSmsInSmsArchiveCountNumber of successful archive of Incoming SMS messages
since router reload. Each SMS message occupies x bytes of
space. So if the incoming message is huge, then it is
archived as multiple of x bytes but still called as one
SMS message. This is the difference between
c3gSmsInSmsArchiveCount and c3gSmsInSmsArchived.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.6 |
c3gSmsInSmsArchiveErrorCountThe number of Incoming SMS messages that could not be
archived since device was reloaded.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.7 |
c3gSmsArchiveUrlURL of the sms archive directory on the ftp server.
The url will be of this format
ftp://x.y.z.k/user/dirnamero SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.661.1.5.1.1.1.8 |
c3gSmsOutSmsStatusStatus of the last send operation of outgoing
SMS message to the network.ro Enumeration .1.3.6.1.4.1.9.9.661.1.5.1.1.1.9 |
c3gSmsInSmsCountNumber of SMS messages which have been
received successfully and stored in router.
These SMS's are a mirror copy of SMS stored in
Modem or SIMro Counter32 .1.3.6.1.4.1.9.9.661.1.5.1.1.1.10 |
c3gSmsInSmsDeletedNumber of SMS messages which have been
deleted since router boot up. This does
not include SMS messages that are already
archived.ro Counter32 .1.3.6.1.4.1.9.9.661.1.5.1.1.1.11 |
c3gSmsInSmsStorageMaxNumber of SMS message records space allocated
in the router's DRAM to store Incoming SMS messages.ro Counter64 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.12 |
c3gSmsInSmsCallBackNumber of incoming SMS messages that triggered
callback.ro Counter32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.13 |
c3gSmsOutSmsPendingCountNumber of outgoing SMS messages that are in
pending queue of the router.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.14 |
c3gSmsOutSmsArchiveCountNumber of successfull archive of outgoing SMS messages
since router reload.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.15 |
c3gSmsOutSmsArchiveErrorCountNumber of failed archive of outgoing SMS messages
since router reload.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.16 |
c3gSmsInSmsArchivedNumber of Incoming SMS messages that are successfully
archived since router reload.ro Gauge32 UNITS "msgs" .1.3.6.1.4.1.9.9.661.1.5.1.1.1.17 |
ciscoWan3gMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.2 |
ciscoWan3gMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.2.1 |
ciscoWan3gMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.661.2.2 |