CISCO-VSIMASTER-MIB
AI MIB Summary
The CISCO-VSIMASTER-MIB provides management objects for the master entity of the Virtual Switch Interface (VSI) protocol on Cisco ATM switches, enabling monitoring of VSI control states, session parameters, and master-slave synchronization metrics for ATM virtual circuit management.
This MIB module contains objects related to the master side of the Virtual Switch Interface protocol used for control of ATM switches.
Main OID:
ciscoVsiMasterMIB.1.3.6.1.4.1.9.9.162
90
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
90 total| Object Name |
|---|
ciscoVsiMasterMIBThis MIB module contains objects related to the master side of
the Virtual Switch Interface protocol used for control of ATM
switches. MODULE-IDENTITY .1.3.6.1.4.1.9.9.162 |
ciscoVsiMasterObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.162.1 |
vsiMasterControllerTableA table containing a set of VSI controllers. Each controller
represents an instance of the VSI Master control protocol.
A controller communicates with a set of VSI Slaves across
a control interface. Running the VSI protocol, the controller
supports a network control application.
Through VSI, such an application can control the Virtual
Circuit cross-connect table inside the ATM switch,
perform monitoring and statistics collection of interfaces and
virtual circuits on the switch, and discover configuration
information from within the switch. SEQUENCE OF VsiMasterControllerEntry .1.3.6.1.4.1.9.9.162.1.1 |
vsiMasterControllerEntryAn entry containing management information applicable to a
controller which uses the VSI protocol. Controller entries
represent internally generated control structures. Therefore
each row is created by the agent in response to the learning of
a controller's instantiation. Instantiation of a controller
is performed by the VSI Master protocol implementation under
management via this MIB. These structures, once instantiated,
are never deleted. Each controller manages a set of VSI
slaves, via a protocol instance called a Session. VsiMasterControllerEntry .1.3.6.1.4.1.9.9.162.1.1.1 |
vsiControllerIndexA unique value per VSI controller, greater than 0. This
object gets its value from the vsiControllerId, and is used
for row selection within the vsiMasterControllerTable.ro VsiControllerIndex .1.3.6.1.4.1.9.9.162.1.1.1.1 |
vsiControllerIdThe controller identifier for the VSI controller. Values are
arbitrarily assigned by the VSI protocol implementation being
managed via this MIB, with local significance only. These
values appear in the header of all VSI protocol messages.ro Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.2 |
vsiCrossConnectsThis object contains a value equal to the number of
cross-connects being controlled via VSI protocol via
this controller.ro Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.3 |
vsiControllerTypeA VSI controller represents an instance of a service layer
accessible to a network control application. This object
serves to identify the type of the network control
application currently being supported by this controller.
other(1): the type is unspecified.
mpls(2): indicates that the client is a Label Switch
Controller performing Multi Protocol Label Switching.
pnni(3): indicates that the client is an instance of the
ATM Private Network to Network Interface.
par(4): indicates that the client is an instance of ATM
Portable Autoroute.ro Enumeration .1.3.6.1.4.1.9.9.162.1.1.1.4 |
vsiBaseVersionSupportedA VSI Master protocol instance defines internally a set of
versions of the protocol that it will support. These versions
are numbered, by default, starting from 1. This object
makes available the lowest numbered version that the VSI
Master protocol supports. This object is related to the other
vsiMasterControllerEntry objects, vsiTopVersionSupported and
vsiVersionInUse.ro Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.5 |
vsiTopVersionSupportedA VSI Master protocol instance defines internally a set of
versions of the protocol that it will support. These versions
are numbered, by default, starting from 1. This object
makes available the highest numbered version that the VSI
Master protocol supports. This object is related to the other
vsiMasterControllerEntry objects, vsiBaseVersionSupported and
vsiVersionInUse.ro Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.6 |
vsiVersionInUseThe number of the VSI version currently being used by this
controller. Protocol selection procedures dictate that this
should be the highest value of protocol version, between
vsiBaseVersionSupported and vsiTopVersionSupported, that is
supported by all slaves. An exception to this rule will
occur when the version is constrained to a specific value
indicated by the vsiSpecifiedVersion object.ro Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.7 |
vsiSpecifiedVersionWhen this object is written with a non-zero value,
re-synchronization procedures will be initiated, if necessary,
in order to constrain the master and slaves to use the
indicated protocol version. When written with zero (0), the
master and slaves should use the version dictated by the
usual protocol version selection procedures; resynchronization
procedures will be invoked, if necessary, to achieve this
result.rw Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.8 |
vsiControlInterfaceA VSI controller communicates with a set of VSI Slaves
across a control interface. The controller is connected to
the ATM switch via an ATM link called the Slave Control Link.
The interface at the Master end of the link is the Master
Control Port, and is described by this object; it is the
ifIndex of this Master Control Port.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.162.1.1.1.9 |
vsiLogicalControlInterfaceThis object describes the instance of a logical interface index
bound to the slave end of the Slave Control Link, which is
referred to in the description of vsiControlInterface.ro VsiLogicalIfIndex .1.3.6.1.4.1.9.9.162.1.1.1.10 |
vsiControlIfIpAddressThe IP address of the interface identified by
the associated vsiControlInterface object.ro IpAddress .1.3.6.1.4.1.9.9.162.1.1.1.11 |
vsiAvailableChnlWarnThresholdA controller has in its domain multiple instances of the
vsiLogicalIfAvailIngressChnls and
vsiLogicalIfAvailEgressChnls counters. This set of values,
associated with all the logical interfaces in the
vsiLogicalIfTable, is monitored so as to note the minimum
value.
The minimum observed value is compared against this threshold
object. If the minimum observed value is less than this
threshold, and the value at the last comparison was greater
than or equal to this threshold, a single event will be
generated, to indicate a warning that available channels are
being depleted. After a warning event is generated, another
such event will not be generated unless the
vsiAvailableChnlAlarmThreshold is reached. If the
vsiAvailableChnlAlarmThreshold is reached and then the minimum
observed value is greater than or equal to this threshold, a
single event is generated, to indicate that a recovery
of resources has occurred.
If this object contains the value zero, then the thresholding
operation will be disabled. Otherwise, the value of this
object must be greater than or equal to the value of the
associated vsiAvailableChnlAlarmThreshold object.
Notification emissions are also gated by the
vsiXCTrapEnable object.rw Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.12 |
vsiAvailableChnlAlarmThresholdA controller has in its domain multiple instances of the
vsiLogicalIfAvailIngressChnls and
vsiLogicalIfAvailEgressChnls counters. This set of values,
associated with all the logical interfaces in the
vsiLogicalIfTable, is monitored so as to note the minimum
value.
The minimum observed value is compared against this threshold
object. If the minimum observed value is less than this
threshold, and the value at the last comparison was greater
than or equal to this threshold, a single event will be
generated, to indicate an alarm that available channels are
being depleted. After an alarm event is generated, another
such event will not be generated unless the
vsiAvailableChnlWarnThreshold is reached.
If this object contains the value zero, then the thresholding
operation will be disabled. Otherwise, the value of this
object must be less than or equal to the value of the
associated vsiAvailableChnlWarnThreshold object.
Notification emissions are also gated by the
vsiXCTrapEnable object.rw Integer32 .1.3.6.1.4.1.9.9.162.1.1.1.13 |
vsiAvailableChnlThresholdStatusAs described for the vsiAvailableChnlWarnThreshold and
vsiAvailableChnlAlarmThreshold objects, events are generated
when these thresholds are crossed. This object defines a
set of unique values that are used with the
vsiLcnExhaustionNotice to convey information about the
context of a threshold crossing.
warning(1): the event qualifier for indicating
vsiAvailableChnlWarnThreshold violations.
alarm(2): the event qualifier for indicating
vsiAvailableChnlAlarmThreshold violations.
recovery(3): the event qualifier for indicating
vsiAvailableChnlWarnThreshold recovery.
normal(4): the initial value that indicates that no
thresholds have been crossed.ro Enumeration .1.3.6.1.4.1.9.9.162.1.1.1.14 |
vsiSessionTableA table containing VSI master-slave session status information.
Each VSI controller manages a set of VSI slaves, via a protocol
instance called a Session. VSI slaves are entities that reside
on the controlled ATM switch. Their number and characteristics
are discovered by the VSI controller via the VSI protocol.
This table has an entry for each slave so discovered. SEQUENCE OF VsiSessionEntry .1.3.6.1.4.1.9.9.162.1.2 |
vsiSessionEntryA vsiSessionEntry is a set of objects that together represent
the status of each instance of VSI protocol and the slave in
an ATM switch to which that instance corresponds. There is
one vsiSession for each slave. The number of slaves is
discovered via the VSI protocol. Each slave is responsible
for a subset of the total number of external interfaces on
the ATM switch. Session entries refer back to their
respective controllers via vsiSessionControllerIndex, and
are in turn referred to by vsiLogicalIfSessionIndex in the
VsiLogicalIfEntry. These entries are never deleted. VsiSessionEntry .1.3.6.1.4.1.9.9.162.1.2.1 |
vsiSessionControllerIndexThe ID of the controller which controls this master-slave
session. This identifies which vsiMasterControllerEntry
represents the controller communicating with a slave through
this Session. VsiControllerIndex .1.3.6.1.4.1.9.9.162.1.2.1.1 |
vsiSessionIndexA VSI controller discovers a set of slaves through VSI
protocol. Each of the discovered slaves is bound to a
protocol Session and each of these Sessions occupies a
row in the vsiSessionTable. This object is the row selector.
The value should remain constant after a VSI session is
reinitialized. VsiSessionIndex .1.3.6.1.4.1.9.9.162.1.2.1.2 |
vsiSessionVpiThe virtual path identifier for this VSI master-slave session.
The Slave Control Link, referred to in the description of
vsiLogicalControlInterface, supports an ATM control VC. This
is the vpi for that link.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.3 |
vsiSessionVciThe virtual channel identifier for this VSI master-slave
session. The Slave Control Link, referred to in the
description of vsiLogicalControlInterface, supports an
ATM control VC. This is the vci for that link.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.4 |
vsiSessionSwitchIdThe identifier of the switch which participates in this VSI
master-slave session. The switch terminates the virtual
circuit identified by the vpi/vci pair referred to by
vsiSessionVpi and vsiSessionVci.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.5 |
vsiSessionSwitchNameThe IP hostname for the slave switch which is controlled by
this session. This is an ascii string of maximum
length 64 characters, learned from the ATM switch.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.162.1.2.1.6 |
vsiSessionSlaveIdThe identifier of the slave for this VSI master-slave session.
This value is learned from the slave on the switch.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.7 |
vsiSessionStateThe state of the VSI session.
inactive(1): communications data structures for communicating
with the slave have been created, but the VSI protocol has
not been started.
unknown(2): slave has been queried, but its configuration data
has not yet been received.
configuring(3): configuration data has been sent to the slave,
but a response has not yet been received.
resyncStarting(4): a re-sync command has been sent to the
slave but a response has not yet been received.
resyncUnderway(5): a re-sync command response has been
received from the slave, but the network applications have
not yet completed reasserting connections.
resyncEnding(6): a command has been sent to end re-sync, but
a response has not yet been received.
discovery(7): a query has been sent to the slave for
interface information, but a response has not yet
been received.
established(8): discovery has completed.
shutdownStarting(9): the master has started an orderly
shutdown of the slave.ro Enumeration .1.3.6.1.4.1.9.9.162.1.2.1.8 |
vsiSessionWindowSizeThe maximum number of command messages the VSI master will
send before requiring a response from slave. If the value
is 0, then flow control is not enabled.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.9 |
vsiSessionCmdsPendingThe number of unacknowledged command messages. The VSI master
sends commands to the slave, without receiving acknowledgement,
until the window size threshold has been reached. This
object is a count of the number of commands that have been
sent and that are awaiting acknowledgment.ro Gauge32 .1.3.6.1.4.1.9.9.162.1.2.1.10 |
vsiSessionActiveIdID supplied by the slave to identify the session. This value
is interpreted by the master, when a change occurs, to
indicate that a resync should be inititated.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.11 |
vsiSessionPowerupIdID supplied by the slave to identify the session at powerup.
This is the initial value for vsiSessionActiveId, and its
default is zero. Changes in vsiSessionActiveId signal a
resync.ro Integer32 .1.3.6.1.4.1.9.9.162.1.2.1.12 |
vsiLogicalIfTableA table containing information about logical interfaces
on the slave switch controlled via VSI. Logical interfaces
are an abstraction of exposed, external ATM interfaces that
are available for connections. When two external interfaces,
represented by two logical interfaces, are paired, they
provide physical paths through the switch. These physical
pathways support cross-connects. SEQUENCE OF VsiLogicalIfEntry .1.3.6.1.4.1.9.9.162.1.3 |
vsiLogicalIfEntryAn entry containing information about a single VSI
logical interface. Entries are instantiated and removed
as signalled by the slave which controls the external
interface. Each entry contains information about the
capacity of cross-connects the interface can bear, cell
rate, merge capability, vpi/vci ranges, and statistics.
Pairs of logical interfaces support potential cross-connects
that, when actualized, are represented by the vsiXCEntrys
in the vsiXCTable.
Logical interfaces are controlled by a designated slave,
as determined by the switch. The slave is in the
domain of the controller whose identity is given
by vsiLogicalIfControllerIndex. This object is an opaque
identifier, provided by the slave, and used as a key to
identify the entry. VsiLogicalIfEntry .1.3.6.1.4.1.9.9.162.1.3.1 |
vsiLogicalIfControllerIndexThe VSI controller index of the controller through which
this logical interface was learned.ro VsiControllerIndex .1.3.6.1.4.1.9.9.162.1.3.1.1 |
vsiLogicalIfIndexA unique value, greater than zero, for each VSI logical
interface. Logical interface numbers are selected by the
switch to be unique and persistent. The same number is
preserved through power failures. This index is not the same
as an ifIndex. It is an abstract number provided by the slave,
representing a virtual interface, which is an identifier to be
used when communicating with the slave about an interface.ro VsiLogicalIfIndex .1.3.6.1.4.1.9.9.162.1.3.1.2 |
vsiLogicalIfNameThe physical descriptor of the logical interface, as
reported by the VSI slave. It is distinct from ifName.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.162.1.3.1.3 |
vsiLogicalIfOperStateThe VSI operational state of the logical interface as
reported to the VSI master by the VSI slave.
removed(1): the interface is not a valid interface on this
controller, is not part of the controller's
partition, or is not available.
active(2): the interface is active and ready for use.
failedExternal(3): external failure, such as a line alarm,
detected.
failedInternal(4): local hardware has detected a failure,
making the interface unusable.ro Enumeration .1.3.6.1.4.1.9.9.162.1.3.1.4 |
vsiLogicalIfAdminStateThe current administrative (configured) state of the
interface, as reported to the VSI master by the VSI slave.
down(1): the interface is not a valid interface for the
controller.
up(2): the interface is configured for use by the controller.
pendingDown(3): the interface is being removed from service,
and the controller is requested to remove all connections.ro Enumeration .1.3.6.1.4.1.9.9.162.1.3.1.5 |
vsiLogicalIfRxCellsThe number of cells received via this logical interface
as reported to the VSI master by the VSI slave.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.6 |
vsiLogicalIfTxCellsThe number of cells transmitted via this logical
interface as reported to the VSI master by the VSI slave.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.7 |
vsiLogicalIfRxCellsDiscardedThe number of received cells discarded by this logical
interface as reported to the VSI master by the VSI slave.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.8 |
vsiLogicalIfTxCellsDiscardedThe number of transmitted cells discarded by this logical
interface as reported to the VSI master by the VSI slave.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.9 |
vsiLogicalIfRxHeaderErrorsThe number of cells received via this logical
interface which had header errors, as reported to
the VSI master by the VSI slave.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.10 |
vsiLogicalIfRxInvalidAddrsThe number of cells received by this logical
interface which had invalid addresses, as
reported to the VSI master by the VSI slave.
An unknown vpi/vci value set is an example of
of an invalid address.ro Counter32 .1.3.6.1.4.1.9.9.162.1.3.1.11 |
vsiLogicalIfEndPointsInUseThe number of end points in use on this logical
interface, as reported to the VSI master by the
VSI slave. This reflects an aggregate count of
input, output and bi-directional end points.
If the logical interface has not been
removed, but does not currently support any cross
connects, this object will be reported as zero (0).ro Gauge32 .1.3.6.1.4.1.9.9.162.1.3.1.12 |
vsiLogicalIfAvailIngressChnlsThe number of ingress channels available for this
logical interface, as reported to the VSI master
by the VSI slave.ro Gauge32 .1.3.6.1.4.1.9.9.162.1.3.1.13 |
vsiLogicalIfAvailEgressChnlsThe number of egress channels available for this
logical interface, as reported to the VSI master
by the VSI slave.ro Gauge32 .1.3.6.1.4.1.9.9.162.1.3.1.14 |
vsiLogicalIfAvailIngressCellRateThe available ingress cell rate in cells/second
for the logical interface, as reported to the VSI
master by the VSI slave.ro Gauge32 .1.3.6.1.4.1.9.9.162.1.3.1.15 |
vsiLogicalIfAvailEgressCellRateThe available egress cell rate in cells/second
for the logical interface, as reported to the VSI
master by the VSI slave.ro Gauge32 .1.3.6.1.4.1.9.9.162.1.3.1.16 |
vsiLogicalIfVcMergeSupportedIf this object has the value true(1) then VC merge
capability is supported for this logical interface.
Otherwise VC merge capability is not supported on
this logical interface.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.3.1.17 |
vsiLogicalIfMulticastSupportedIf this object has the value true(1) then multicast
capability is supported for this logical interface.
Otherwise multicast capability is not supported on
this logical interface.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.3.1.18 |
vsiLogicalIfVpiTranslatedIf this object has the value true(1) then vpi values
entering on this logical interface are translated at
the other end of the link. This translation may be
an indication that the link is supporting a tunnel.
Otherwise, vpi values are not translated for traversal
of the link.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.3.1.19 |
vsiLogicalIfStrictSigRangeIf this object has the value true(1) then signalling
addresses must be in the strict advertised range for
the high-address (vpi). Otherwise, signalling addresses
are not so constrained.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.3.1.20 |
vsiLogicalIfMaxIngressCellRateThe maximum ingress cell rate in cells/second for the
logical interface, as reported to the VSI. This value is
the limiting value for vsiLogicalIfAvailIngressCellRate.ro Integer32 .1.3.6.1.4.1.9.9.162.1.3.1.21 |
vsiLogicalIfMaxEgressCellRateThe maximum egress cell rate in cells/second
for the logical interface, as reported to the VSI
master by the VSI slave.ro Integer32 .1.3.6.1.4.1.9.9.162.1.3.1.22 |
vsiLogicalIfMinVpiMinimum allowed vpi value for this interface
as reported by VSI slave switch.ro INTEGER .1.3.6.1.4.1.9.9.162.1.3.1.23 |
vsiLogicalIfMaxVpiMaximum allowed vpi value for this interface
as reported by VSI slave switch.ro INTEGER .1.3.6.1.4.1.9.9.162.1.3.1.24 |
vsiLogicalIfMinVciMinimum allowed vci value for this interface
as reported by VSI slave switch.ro INTEGER .1.3.6.1.4.1.9.9.162.1.3.1.25 |
vsiLogicalIfMaxVciMaximum allowed vci value for this interface
as reported by VSI slave switch.ro INTEGER .1.3.6.1.4.1.9.9.162.1.3.1.26 |
vsiLogicalControlIfIndexThe interface index for the interface which
controls this logical interface. This is the ifIndex
of the controlling network layer interface, and
is a direct manifestation of the mapping between
a logical interface and the real ifIndex.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.162.1.3.1.27 |
vsiLogicalIfSessionIndexAll logical interfaces are in the domain of a VSI slave,
which communicates with the VSI master through a Session.
This object is a selector for an entry in the table
vsiSessionTable. It is the VSI session index for the VSI
session which controls this logical interface.ro VsiSessionIndex .1.3.6.1.4.1.9.9.162.1.3.1.28 |
vsiXCTableA table containing information about cross-connects
on the slave switch controlled via VSI. cross-connects
represent virtual links across two interfaces. The
participating interfaces that support these links are
represented in this MIB by the vsiLogicalIfTable entries. SEQUENCE OF VsiXCEntry .1.3.6.1.4.1.9.9.162.1.4 |
vsiXCEntryAn entry containing information about one unidirectional
or bidirectional cross-connect on the slave switch
controlled via VSI. A VSI controller represents an instance
of a service layer accessible to a network control application.
The application creates virtual links via service requests to
the controller, which in turn sends commands to the VSI slave,
indicating the participating logical interfaces. Conversely,
links are taken down by a reverse process. Virtual link
creation and deletion come about as a result of routing
decisions. VsiXCEntry .1.3.6.1.4.1.9.9.162.1.4.1 |
vsiXCControllerIndexThe index of the VSI controller through which this
cross-connect was instantiated. This object is the index for
a vsiControllerTable entry; the controller indexed is
the VSI protocol partner to the slave that is controlling
the logical interfaces on which this cross-connect is
supported.ro VsiControllerIndex .1.3.6.1.4.1.9.9.162.1.4.1.1 |
vsiXCLogicalIfLowThe VSI logical interface index for the first endpoint
of the cross-connect. This object is the selector index
for one of the two vsiLogicalIfTable entries that support this
cross-connect. Further, this index value is constrained
to be 'numerically lower than' the index value of the other
vsiLogicalIfTable entry, indexed by vsiXCLogicalIfHi,
supporting this cross-connect.ro VsiLogicalIfIndex .1.3.6.1.4.1.9.9.162.1.4.1.2 |
vsiXCLogicalIfHiThe VSI logical interface index for the second endpoint
of the cross-connect. This object is the selector index
for one of the two vsiLogicalIfTable entries that support this
cross-connect. Further, this index value is constrained
to be 'numerically higher than' the index value of the other
vsiLogicalIfTable entry, indexed by vsiXCLogicalIfLow,
supporting this cross-connect.ro VsiLogicalIfIndex .1.3.6.1.4.1.9.9.162.1.4.1.3 |
vsiXCIndexA unique value greater than zero, for each cross-connect
within the set of VsiXCTable entries indexed by
vsiXCLogicalIfLow and vsiXCLogicalIfHi.
The value should remain constant after a cross-connect
is initialized. These values are assigned in sequence
by the management agent, starting from one (1).ro VsiXCIndex .1.3.6.1.4.1.9.9.162.1.4.1.4 |
vsiXCStateThe operational state of the cross-connect, as reported
to the VSI master by the VSI slave.
deleted(1): the connection does not exist.
reserved(2): connection is in the reserved state.
committed(3): connection is in the committed state.
reservedFail(4): connection is reserved but has an internal
failure.ro Enumeration .1.3.6.1.4.1.9.9.162.1.4.1.5 |
vsiXCVpiLowThe vpi of that endpoint of the cross-connect which
terminates on the logical interface whose index is
given by vsiXCLogicalIfLow.ro Integer32 .1.3.6.1.4.1.9.9.162.1.4.1.6 |
vsiXCVciLowThe vci of that endpoint of the cross-connect which
terminates on the logical interface whose index is
given by vsiXCLogicalIfLow.ro Integer32 .1.3.6.1.4.1.9.9.162.1.4.1.7 |
vsiXCVpiHiThe vpi of that endpoint of the cross-connect which
terminates on the logical interface whose index is
given by vsiXCLogicalIfHi.ro Integer32 .1.3.6.1.4.1.9.9.162.1.4.1.8 |
vsiXCVciHiThe vci of that endpoint of the cross-connect which
terminates on the logical interface whose index is
given by vsiXCLogicalIfHi.ro Integer32 .1.3.6.1.4.1.9.9.162.1.4.1.9 |
vsiControllerTrapEnableIf this object is true, both vsiControllerAdded and
vsiControllerDeleted notifications are enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.5 |
vsiSessionTrapEnableIf this object is true, both vsiSessionUp
and vsiSessionDown notifications are enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.6 |
vsiLogicalIfTrapEnableIf this object is true, both vsiLogicalIfUp
and vsiLogicalIfDown notifications are enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.7 |
vsiXCTrapEnableIf this object is true, both vsiXCFailed and
vsiLcnExhaustionNotice notifications are enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.8 |
vsiVSITrapEnableIf this object is true, all of
vsiControllerTrapEnable, vsiSessionTrapEnable,
vsiLogicalIfTrapEnable, and vsiXCTrapEnable
are also set to true. This allows for enabling
and disabling all notifications as a group.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.162.1.9 |
ciscoVsiMasterNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.162.2 |
vsiControllerAddedThis notification is generated when a vsiMasterControllerEntry
is added to the vsiMasterControllerTable.
The vsiControllerType object identifies the type and instance
of the entry that was added.
The agent will not generate this notification if the
vsiControllerTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.1 |
vsiControllerDeletedThis notification is generated when a vsiMasterControllerEntry
is deleted from the vsiMasterControllerTable.
The vsiControllerType object identifies the type and instance
of the entry that was deleted.
The agent will not generate this notification if the
vsiControllerTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.2 |
vsiSessionUpThis notification is generated when the vsiSessionState
object transitions to the established(8) state.
The vsiSessionState object identifies the state and instance
of the session, after the session has made the transition that
caused the notification to be generated.
The agent will not generate this notification if the
vsiSessionTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.3 |
vsiSessionDownThis notification is generated when the vsiSessionState
object transitions from any of unknown(1), configuring(2), or
established(8) state to shutdownStarting(9) states.
This notification is also generated when the vsiSessionState
transitions from configuring(2) or established(8) state to
the unknown(1) state.
The vsiSessionState object identifies the state and instance
of the session, after the session has made the transition that
caused the notification to be generated.
The agent will not generate this notification if the
vsiSessionTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.4 |
vsiLogicalIfUpThis notification is generated when the vsiLogicalIfOperState
object transitions to the active(2) state.
The vsiLogicalIfOperState object identifies the state and
instance of the logical interface, after the logical interface
has made the transition that caused the notification to be
generated.
The agent will not generate this notification if the
vsiLogicalIfTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.5 |
vsiLogicalIfDownThis notification is generated when the vsiLogicalIfOperState
object transitions from the active(2) state to either the
failedExternal(3) or failedInternal(4) state.
The vsiLogicalIfOperState object identifies the state and
instance of the logical interface, after the logical interface
has made the transition that caused the notification to be
generated.
The agent will not generate this notification if the
vsiLogicalIfTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.6 |
vsiXCFailedThis notification is generated when an attempt to create a
cross-connect fails. Failure means the slave has answered
a connect command with a nak, reject, or error response.
The vsiXCControllerIndex object identifies the
VsiControllerIndex of the VSI controller through which the
cross-connect was attempted.
The vsiXCLogicalIfLow object provides the lower valued
VsiLogicalIfIndex of the logical interface on which the
cross-connect was attempted.
The vsiXCLogicalIfHi object provides the higher valued
VsiLogicalIfIndex of the logical interface on which the
cross-connect was attempted.
The agent will not generate this notification if the
vsiXCTrapEnable object is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.7 |
vsiLcnExhaustionNoticeAs cross-connects on logical interfaces are instantiated or
released, and available channel counts are respectively
diminished or augmented, there is a potential for the
available channel counts to cross a threshold. The threshold
value may be crossed in the positive direction as the
available channel count is rising, or in a negative direction
as the available channel count is falling. The threshold
values are described as the vsiAvailableChnlWarnThreshold and
the vsiAvailableChnlAlarmThreshold objects.
The vsiControllerIndex identifies the controller domain in
which the threshold event took place.
The vsiAvailableChnlThresholdStatus indicates the particular
kind of threshold crossing that occurred.
When comparison with vsiAvailableChnlWarnThreshold indicates a
negative crossing, this notification, with
vsiAvailableChnlThresholdStatus:warning(1) is emitted.
When comparison with vsiAvailableChnlAlarmThreshold indicates
a negative threshold violation, this notification, with
vsiAvailableChnlThresholdStatus:alarm(2) is emitted.
When comparison with vsiAvailableChnlWarnThreshold indicates a
positive threshold crossing, and if the preceeding
vsiLcnExhaustionNotice had been sent with the
vsiAvailableChnlThresholdStatus:alarm(2) parameter, this
notification, with vsiAvailableChnlThresholdStatus:recovery(3)
is emitted.
The agent will not generate this notification if the
vsiXCTrapEnable is equal to 'false'. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.162.2.8 |
ciscoVsiMasterConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.162.3 |
ciscoVsiMasterGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.162.3.1 |
ciscoVsiMasterCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.162.3.2 |