CISCO-VLAN-MEMBERSHIP-MIB
AI MIB Summary
The CISCO-VLAN-MEMBERSHIP-MIB monitors Cisco VLAN Architecture v2.0 devices to track VLAN Membership Policy Server configurations and non-trunk bridge port VLAN assignments. It provides visibility into dynamic VLAN membership states and policy server interactions for frame-relay and bridge port interfaces.
The MIB module for the management of the VLAN Membership within the frame work of Cisco VLAN Architecture, v 2.0 by Keith McCloghrie. The MIB provides information on VLAN Membership Policy Servers used by a device and VLAN membership assignments of non-trunk bridge ports of the device.
60
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
60 total| Object Name |
|---|
ciscoVlanMembershipMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9.9.68 |
ciscoVlanMembershipMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1 |
vmVmps OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1.1 |
vmVmpsVQPVersionThe VLAN Query Protocol (VQP) version supported on
the device. VQP is the protocol used to query
VLAN Membership Policy Server (VMPS) for VLAN
membership assignments of dynamic VLAN ports.
A VMPS provides VLAN membership policy
assignments based on the content of the packets
received on a port.ro INTEGER .1.3.6.1.4.1.9.9.68.1.1.1 |
vmVmpsRetriesThe number of retries for VQP requests to a VMPS before
using the next available VMPS.rw INTEGER .1.3.6.1.4.1.9.9.68.1.1.2 |
vmVmpsReconfirmIntervalThe switch will reconfirm membership of addresses on
each port with VMPS periodically. This object specifies
the interval to perform reconfirmation. If the value is
set to 0, the switch does not reconfirm membership with
VMPS.rw INTEGER .1.3.6.1.4.1.9.9.68.1.1.3 |
vmVmpsReconfirmSetting this object to execute(2) causes the switch
to reconfirm membership of every dynamic port.
Reading this object always return ready(1).rw Enumeration .1.3.6.1.4.1.9.9.68.1.1.4 |
vmVmpsReconfirmResultThis object returns the result of the last request
that sets vmVmpsReconfirm to execute(2). The
semantics of the possible results are as follows:
other(1) - none of following
inProgress(2) - reconfirm in progress
success(3) - reconfirm completed successfully
noResponse(4) - reconfirm failed because no
VMPS responded
noVmps(5) - No VMPS configured
noDynamicPort(6) - No dynamic ports configured
noHostConnected(7) - No hosts on dynamic portsro Enumeration .1.3.6.1.4.1.9.9.68.1.1.5 |
vmVmpsCurrentThis is the IpAddress of the current VMPS used.ro IpAddress .1.3.6.1.4.1.9.9.68.1.1.6 |
vmVmpsTableA table of VMPS to use. The device will use
the the primary VMPS by default. If the
device is unable to reach the primary server
after vmVmpsRetries retries, it uses the first
secondary server in the table until it runs out
of secondary servers, in which case it will return
to using the primary server. Entries in this table
may be created and deleted via this MIB or
the management console on a device. SEQUENCE OF VmVmpsEntry .1.3.6.1.4.1.9.9.68.1.1.7 |
vmVmpsEntryAn entry (conceptual row) in the vmVmpsTable. VmVmpsEntry .1.3.6.1.4.1.9.9.68.1.1.7.1 |
vmVmpsIpAddressThe Ip Address of the VMPS.ro IpAddress .1.3.6.1.4.1.9.9.68.1.1.7.1.1 |
vmVmpsPrimaryThe status of the VMPS. Setting this value
to true will make this VMPS the primary server
and make the switch use this as the current server.
Setting this entry to true causes other rows
to transition to false. Attempting to write
a value of false after creation will result in
a return of bad value. Deleting an entry whose
value is true will result in the first entry
in the table being set to true.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.68.1.1.7.1.2 |
vmVmpsRowStatusThe status of this conceptual row.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.68.1.1.7.1.3 |
vmMembership OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1.2 |
vmMembershipSummaryTableA summary of VLAN membership of non-trunk
bridge ports. This is a convenience table
for retrieving VLAN membership information.
A row is created for a VLAN if:
a) the VLAN exists, or
b) a port is assigned to a non-existent VLAN.
VLAN membership can only be modified via the
vmMembershipTable. SEQUENCE OF VmMembershipSummaryEntry .1.3.6.1.4.1.9.9.68.1.2.1 |
vmMembershipSummaryEntryAn entry (conceptual row) in the
vmMembershipSummaryTable. VmMembershipSummaryEntry .1.3.6.1.4.1.9.9.68.1.2.1.1 |
vmMembershipSummaryVlanIndexThe VLAN id of the VLAN. VlanIndex -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.68.1.2.1.1.1 |
vmMembershipSummaryMemberPortsThe set of the device's member ports that belong
to the VLAN.
Each octet within the value of this object specifies a
set of eight ports, with the first octet specifying ports
1 through 8, the second octet specifying ports 9
through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
port, and the least significant bit represents the
highest numbered port. Thus, each port of the
VLAN is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that port is included in the set of
ports; the port is not included if its bit has a
value of '0'.
A port number is the value of dot1dBasePort for
the port in the BRIDGE-MIB (RFC 1493).ro OCTET STRING .1.3.6.1.4.1.9.9.68.1.2.1.1.2 |
vmMembershipTableA table for configuring VLAN port membership.
There is one row for each bridge port that is
assigned to a static or dynamic access port. Trunk
ports are not represented in this table. An entry
may be created and deleted when ports are created or
deleted via SNMP or the management console on a device. SEQUENCE OF VmMembershipEntry .1.3.6.1.4.1.9.9.68.1.2.2 |
vmMembershipEntryAn entry (conceptual row) in the vmMembershipTable. VmMembershipEntry .1.3.6.1.4.1.9.9.68.1.2.2.1 |
vmVlanTypeThe type of VLAN membership assigned to this port.
A port with static vlan membership is assigned to a
single VLAN directly. A port with dynamic membership
is assigned a single VLAN based on content of packets
received on the port and via VQP queries to VMPS.
A port with multiVlan membership may be assigned to
one or more VLANs directly.
A static or dynamic port membership is specified
by the value of vmVlan. A multiVlan port membership is
specified by the value of vmVlans.rw Enumeration .1.3.6.1.4.1.9.9.68.1.2.2.1.1 |
vmVlanThe VLAN id of the VLAN the port is assigned to
when vmVlanType is set to static or dynamic.
This object is not instantiated if not applicable.
The value may be 0 if the port is not assigned
to a VLAN.
If vmVlanType is static, the port is always
assigned to a VLAN and the object may not be
set to 0.
If vmVlanType is dynamic the object's value is
0 if the port is currently not assigned to a VLAN.
In addition, the object may be set to 0 only.rw INTEGER .1.3.6.1.4.1.9.9.68.1.2.2.1.2 |
vmPortStatusAn indication of the current VLAN status of the port.
A status of inactive(1) indicates that a dynamic port
does not yet have a VLAN assigned, or a port is assigned
to a VLAN that is currently not active. A status of
active(2) indicates that the currently assigned
VLAN is active. A status of shutdown(3) indicates
that the port has been disabled as a result of VQP
shutdown response.ro Enumeration .1.3.6.1.4.1.9.9.68.1.2.2.1.3 |
vmVlansThe VLAN(s) the port is assigned to when the
port's vmVlanType is set to multiVlan.
This object is not instantiated if not applicable.
The port is always assigned to one or more VLANs
and the object may not be set so that there are
no vlans assigned.
Each octet within the value of this object specifies a
set of eight VLANs, with the first octet specifying
VLAN id 1 through 8, the second octet specifying VLAN
ids 9 through 16, etc. Within each octet, the most
significant bit represents the lowest numbered
VLAN id, and the least significant bit represents the
highest numbered VLAN id. Thus, each VLAN of the
port is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that VLAN is included in the set of
VLANs; the VLAN is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.9.68.1.2.2.1.4 |
vmVlans2kThe VLAN(s) the port is assigned to when the
port's vmVlanType is set to multiVlan.
This object is not instantiated if not applicable.
The port is always assigned to one or more VLANs
and the object may not be set so that there are
no vlans assigned.
Each octet within the value of this object specifies a
set of eight VLANs, with the first octet specifying
VLAN id 1024 through 1031, the second octet specifying VLAN
ids 1032 through 1039, etc. Within each octet, the most
significant bit represents the lowest numbered
VLAN id, and the least significant bit represents the
highest numbered VLAN id. Thus, each VLAN of the
port is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that VLAN is included in the set of
VLANs; the VLAN is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.9.68.1.2.2.1.5 |
vmVlans3kThe VLAN(s) the port is assigned to when the
port's vmVlanType is set to multiVlan.
This object is not instantiated if not applicable.
The port is always assigned to one or more VLANs
and the object may not be set so that there are
no vlans assigned.
Each octet within the value of this object specifies a
set of eight VLANs, with the first octet specifying
VLAN id 2048 through 2055, the second octet specifying VLAN
ids 2056 through 2063, etc. Within each octet, the most
significant bit represents the lowest numbered
VLAN id, and the least significant bit represents the
highest numbered VLAN id. Thus, each VLAN of the
port is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that VLAN is included in the set of
VLANs; the VLAN is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.9.68.1.2.2.1.6 |
vmVlans4kThe VLAN(s) the port is assigned to when the
port's vmVlanType is set to multiVlan.
This object is not instantiated if not applicable.
The port is always assigned to one or more VLANs
and the object may not be set so that there are
no vlans assigned.
Each octet within the value of this object specifies a
set of eight VLANs, with the first octet specifying
VLAN id 3072 through 3079, the second octet specifying VLAN
ids 3040 through 3047, etc. Within each octet, the most
significant bit represents the lowest numbered
VLAN id, and the least significant bit represents the
highest numbered VLAN id. Thus, each VLAN of the
port is represented by a single bit within the
value of this object. If that bit has a value of
'1' then that VLAN is included in the set of
VLANs; the VLAN is not included if its bit has a
value of '0'.rw OCTET STRING .1.3.6.1.4.1.9.9.68.1.2.2.1.7 |
vmStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1.3 |
vmVQPQueriesThe total number of VQP requests sent by this device to
all VMPS since last system re-initialization.ro Counter .1.3.6.1.4.1.9.9.68.1.3.1 |
vmVQPResponsesThe number of VQP responses received by this device from
all VMPS since last system re-initialization.ro Counter .1.3.6.1.4.1.9.9.68.1.3.2 |
vmVmpsChangesThe number of times, since last system re-initialization,
the current VMPS was changed. The current VMPS is changed
whenever the VMPS fails to response after vmVmpsRetries of
a VQP request.ro Counter .1.3.6.1.4.1.9.9.68.1.3.3 |
vmVQPShutdownThe number of times, since last system re-initialization,
a VQP response indicates 'shutdown'. A 'shutdown' response
is a result of the membership policy configured at a VMPS
by the administrator.ro Counter .1.3.6.1.4.1.9.9.68.1.3.4 |
vmVQPDeniedThe number of times, since last system re-initialization,
a VQP response indicates 'denied'. A 'denied' response
is a result of the membership policy configured at a VMPS
by the administrator.ro Counter .1.3.6.1.4.1.9.9.68.1.3.5 |
vmVQPWrongDomainThe number of times, since last system re-initialization,
a VQP response indicates wrong management domain.
A wrong management domain response indicates that the
VMPS used serves a management domain that is different
from the device's management domain.ro Counter .1.3.6.1.4.1.9.9.68.1.3.6 |
vmVQPWrongVersionThe number of times, since last system re-initialization,
a VQP response indicates wrong VQP version.
A wrong VQP version response indicates that the VMPS
used supports a VQP version that is different from
the device's VQP version.ro Counter .1.3.6.1.4.1.9.9.68.1.3.7 |
vmInsufficientResourcesThe number of times, since last system re-initialization,
a VQP response indicates insufficient resources. An
insufficient resources response indicates that the VMPS
used does not have the required resources to verify the
membership assignment requested.ro Counter .1.3.6.1.4.1.9.9.68.1.3.8 |
vmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1.4 |
vmNotificationsEnabledAn indication of whether the notifications/traps
defined in this MIB are enabled.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.68.1.4.1 |
vmVoiceVlan OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.1.5 |
vmVoiceVlanTableA table for configuring the Voice VLAN-ID
for the ports. An entry will exist for each
interface which supports Voice Vlan feature. SEQUENCE OF VmVoiceVlanEntry .1.3.6.1.4.1.9.9.68.1.5.1 |
vmVoiceVlanEntryAn entry (conceptual row) in the vmVoiceVlanTable.
Only interfaces which support Voice Vlan feature
are shown. VmVoiceVlanEntry .1.3.6.1.4.1.9.9.68.1.5.1.1 |
vmVoiceVlanIdThe Voice Vlan ID (VVID) to which this
port belongs to.
0 - The CDP packets transmitting
through this port would contain
Appliance VLAN-ID TLV with value
of 0. VoIP and related packets
are expected to be sent and
received with VLAN-id=0 and an
802.1p priority.
1..4094 - The CDP packets transmitting
through this port would contain
Appliance VLAN-ID TLV with N.
VoIP and related packets are
expected to be sent and received
with VLAN-id=N and an 802.1p
priority.
4095 - The CDP packets transmitting
through this port would contain
Appliance VLAN-ID TLV with value
of 4095. VoIP and related packets
are expected to be sent and
received untagged without an
802.1p priority.
4096 - The CDP packets transmitting
through this port would not
include Appliance VLAN-ID TLV;
or, if the VVID is not supported
on the port, this MIB object will
not be configurable and will
return 4096.rw INTEGER .1.3.6.1.4.1.9.9.68.1.5.1.1.1 |
vmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.2 |
vmNotificationsPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.2.0 |
vmVmpsChangeA VMPS change notification is generated whenever
vmVmpsChanges is incremented. The IP address
of the new VMPS is sent. TRAP-TYPE .1.3.6.1.4.1.9.9.68.2.0.1 |
vmMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3 |
vmMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.1 |
vmMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.1.1 |
vmMIBCompliance2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.1.2 |
vmMIBCompliance3 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.1.3 |
vmMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2 |
vmMembershipGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.1 |
vmVQPClientGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.2 |
vmVQPNotificationsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.3 |
vmStatusGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.4 |
vmMembershipGroup2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.5 |
vm4kVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.6 |
vmVoiceVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.68.3.2.7 |