CISCO-TAP2-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CISCO-TAP2-MIB.
67
Objects
Active
Status
8
Dependencies
Imported Objects
Objects
67 total| Object Name |
|---|
ciscoTap2MIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9.9.399 |
ciscoTap2MIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.0 |
ciscoTap2MIBActiveThis Notification is sent when an intercepting router or
switch is first capable of intercepting a packet corresponding
to a configured data stream. The value of the corresponding
cTap2StreamType which identifies the actual intercept stream
type is included in this notification.
This notification may be generated in conjunction with the
intercept application, which is designed to expect the
notification to be sent as reliably as possible, e.g., through
the use of a finite number of retransmissions until
acknowledged, as and when such mechanisms are available; for
example, with SNMPv3, this would be an InformRequest. Filter
installation can take a long period of time, during which call
progress may be delayed. TRAP-TYPE .1.3.6.1.4.1.9.9.399.0.1 |
ciscoTap2MediationTimedOutWhen an intercept is autonomously removed by an intercepting
device, such as due to the time specified in
cTap2MediationTimeout arriving, the device notifies the manager
of the action. TRAP-TYPE .1.3.6.1.4.1.9.9.399.0.2 |
ciscoTap2MediationDebugWhen there is intervention needed due to some events related
to entries configured in cTap2MediationTable, the device
notifies the manager of the event.
This notification may be generated in conjunction with the
intercept application, which is designed to expect the
notification to be sent as reliably as possible, e.g., through
the use of a finite number of retransmissions until
acknowledged, as and when such mechanisms are available; for
example, with SNMPv3, this would be an InformRequest. TRAP-TYPE .1.3.6.1.4.1.9.9.399.0.3 |
ciscoTap2StreamDebugWhen there is intervention needed due to some events related
to entries configured in cTap2StreamTable, the device
notifies the manager of the event.
This notification may be generated in conjunction with the
intercept application, which is designed to expect the
notification to be sent as reliably as possible, e.g., through
the use of a finite number of retransmissions until
acknowledged, as and when such mechanisms are available; for
example, with SNMPv3, this would be an InformRequest. TRAP-TYPE .1.3.6.1.4.1.9.9.399.0.4 |
ciscoTap2SwitchoverThis notification is sent when there is a redundant (standby)
route processor available on the intercepting device and the
current active processor is going down causing standby to
takeover. Note that this notification may be sent by the
intercepting device only when it had a chance to know before it
goes down.
Mediation device when received this notification should assume
that configured intercepts on the intercepting device no longer
exist, when the standby processor takes control. This means that
the Mediation device should again configure the intercepts. TRAP-TYPE .1.3.6.1.4.1.9.9.399.0.5 |
ciscoTap2MIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.1 |
cTap2MediationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.1.1 |
cTap2MediationNewIndexThis object contains a value which may be used as an index
value for a new cTap2MediationEntry. Whenever read, the agent
will change the value to a new non-conflicting value. This is
to reduce the probability of errors during creation of new
cTap2MediationTable entries.ro INTEGER .1.3.6.1.4.1.9.9.399.1.1.1 |
cTap2MediationTableThis table lists the Mediation Devices with which the
intercepting device communicates. These may be on the same or
different Mediation Devices.
This table is written by the Mediation Device, and is always
volatile. This is because intercepts may disappear during a
restart of the intercepting equipment.
Entries are added to this table via cTap2MediationStatus in
accordance with the RowStatus convention. SEQUENCE OF CTap2MediationEntry .1.3.6.1.4.1.9.9.399.1.1.2 |
cTap2MediationEntryThe entry describes a single session maintained with an
application on a Mediation Device. CTap2MediationEntry .1.3.6.1.4.1.9.9.399.1.1.2.1 |
cTap2MediationContentIdcTap2MediationContentId is a session identifier, from the
intercept application's perspective, and a content identifier
from the Mediation Device's perspective. The Mediation Device
is responsible for making sure these are unique, although the
SNMP RowStatus row creation process will help by not allowing
it to create conflicting entries. Before creating a new entry,
a value for this variable may be obtained by reading
cTap2MediationNewIndex to reduce the probability of a value
collision. INTEGER .1.3.6.1.4.1.9.9.399.1.1.2.1.1 |
cTap2MediationDestAddressTypeThe type of cTap2MediationDestAddress.rw InetAddressType -- Rsyntax INTEGER { -- ?? enum value of zero may cause problems -- unknown(0), -- ipv4(1), -- ipv6(2), -- ipv4z(3), -- ipv6z(4), -- dns(16) -- } .1.3.6.1.4.1.9.9.399.1.1.2.1.2 |
cTap2MediationDestAddressThe IP Address of the Mediation Device's network interface
to which to direct intercepted traffic.rw InetAddress -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.399.1.1.2.1.3 |
cTap2MediationDestPortThe port number on the Mediation Device's network interface
to which to direct intercepted traffic.rw InetPortNumber -- Rsyntax Gauge .1.3.6.1.4.1.9.9.399.1.1.2.1.4 |
cTap2MediationSrcInterfaceThe interface on the intercepting device from which to
transmit intercepted data. If zero, any interface may be used
according to normal IP practice.rw InterfaceIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.399.1.1.2.1.5 |
cTap2MediationRtcpPortThe port number on the intercepting device to which the
Mediation Devices directs RTCP Receiver Reports and Nacks.
This object is only relevant when the value of
cTap2MediationTransport is 'rtpNack'.
This port is assigned by the intercepting device, rather than
by the Mediation Device or manager application. The value of
this MIB object has no effect before activating the
cTap2MediationEntry.ro InetPortNumber -- Rsyntax Gauge .1.3.6.1.4.1.9.9.399.1.1.2.1.6 |
cTap2MediationDscpThe Differentiated Services Code Point the intercepting
device applies to the IP packets encapsulating the
intercepted traffic.rw Ctap2Dscp -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.399.1.1.2.1.7 |
cTap2MediationDataTypeIf RTP with Ack/Nack resilience is selected as a transport,
the mediation process requires an RTP payload type for data
transmissions, and a second RTP payload type for
retransmissions. This is the RTP payload type for
transmissions.
This object is only effective when the value of
cTap2MediationTransport is 'rtpNack'.rw INTEGER .1.3.6.1.4.1.9.9.399.1.1.2.1.8 |
cTap2MediationRetransmitTypeIf RTP with Ack/Nack resilience is selected as a transport,
the mediation process requires an RTP payload type for data
transmissions, and a second RTP payload type for
retransmissions. This is the RTP payload type for
retransmissions.
This object is only effective when the value of
cTap2MediationTransport is 'rtpNack'.rw INTEGER .1.3.6.1.4.1.9.9.399.1.1.2.1.9 |
cTap2MediationTimeoutThe time at which this row and all related Stream Table rows
should be automatically removed, and the intercept function
cease. Since the initiating network manager may be the only
device able to manage a specific intercept or know of its
existence, this acts as a fail-safe for the failure or removal
of the network manager. The object is only effective when the
value of cTap2MediationStatus is 'active'.rw DateAndTime -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.399.1.1.2.1.10 |
cTap2MediationTransportThe protocol used in transferring intercepted data to the
Mediation Device. The following protocols may be supported:
udp: PacketCable udp format
rtpNack: RTP with Nack resilience
tcp: TCP with head of line blocking
sctp: SCTP with head of line blocking
rtp: Realtime Transport Protocol(RTP)
packet formatrw Enumeration .1.3.6.1.4.1.9.9.399.1.1.2.1.11 |
cTap2MediationNotificationEnableThis variable controls the generation of any notifications or
informs by the MIB agent for this table entry.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.399.1.1.2.1.12 |
cTap2MediationStatusThe status of this conceptual row. This object is used to
manage creation, modification and deletion of rows in this
table.
cTap2MediationTimeout may be modified at any time (even while
the row is active). But when the row is active, the other
writable objects may not be modified without setting its value
to 'notInService'.
The entry may not be deleted or deactivated by setting its
value to 'destroy' or 'notInService' if there is any associated
entry in cTap2StreamTable.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.399.1.1.2.1.13 |
cTap2MediationCapabilitiesThis object displays the device capabilities with respect to
certain fields in Mediation Device table. This may be dependent
on hardware capabilities, software capabilities.
The following values may be supported:
ipV4SrcInterface: SNMP ifIndex Value may be used to select
the interface (denoted by
cTap2MediationSrcInterface) on the
intercepting device from which to
transmit intercepted data to an IPv4
address Mediation Device.
ipV6SrcInterface: SNMP ifIndex Value may be used to select
the interface (denoted by
cTap2MediationSrcInterface) on the
intercepting device from which to
transmit intercepted data to an IPv6
address Mediation Device.
udp: UDP may be used as transport protocol
(denoted by cTap2MediationTransport) in
transferring intercepted data to the
Mediation Device.
rtcpNack: RTP with Nack resilience may be used
as transport protocol (denoted by
cTap2MediationTransport) in transferring
intercepted data to the Mediation
Device.
tcp: TCP may be used as transport protocol
(denoted by cTap2MediationTransport) in
transferring intercepted data to the
Mediation Device.
sctp: SCTP may be used as transport protocol
(denoted by cTap2MediationTransport) in
transferring intercepted data to the
Mediation Device.
rtp: RTP may be used as transport protocol
(denoted by cTap2MediationTransport) in
transferring intercepted data to the
Mediation Device.ro OCTET STRING .1.3.6.1.4.1.9.9.399.1.1.3 |
cTap2StreamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.1.2 |
cTap2StreamTableThe Intercept Stream Table lists the traffic streams to be
intercepted. The same data stream may be required by multiple
taps, and one might assume that often the intercepted stream
is a small subset of the traffic that could be intercepted.
The Table consists of generic fields that are independent
of the type of intercept. It contains type of the specific
filter which is defined in an extension MIB and counters to
account for packets intercepted or dropped by the attached
filter specification.
Note that the Mediation Device must make sure there is
only one type of specific filter created with the same
indices as that of a row in this table, otherwise the
later creations will fail. For example, if there is a
row in this table with index 1.2, there can be a
corresponding row with the same index either in
citapStreamTable, c8tapStreamTable or cuctTapStreamTable,
but not all.
The first index indicates which Mediation Device the
intercepted traffic will be diverted to. The second index
permits multiple classifiers to be used together.
Entries are added to this table via cTap2StreamStatus in
accordance with the RowStatus convention. SEQUENCE OF CTap2StreamEntry .1.3.6.1.4.1.9.9.399.1.2.1 |
cTap2StreamEntryA stream entry indicates a single data stream to be
intercepted to a Mediation Device. Many selected data
streams may go to the same application interface, and many
application interfaces are supported. CTap2StreamEntry .1.3.6.1.4.1.9.9.399.1.2.1.1 |
cTap2StreamIndexThe index of the stream itself. INTEGER .1.3.6.1.4.1.9.9.399.1.2.1.1.1 |
cTap2StreamTypeIdentifies the type of intercept filter associated to this
generic stream. The following types of streams are supported:
ip: The specific filter is an IP filter
with same indices as that of this
table. The exact filter is a row in
citapStreamTable of CISCO-IP-TAP-MIB.
mac: The specific filter is a MAC filter
with same indices as that of this table.
The exact filter is a row in
c8tapStreamTable of CISCO-802-TAP-MIB.
userConnecton: The specific filter is a user connection
filter with same indices as that of
this table. The exact filter is a row
in cuctTapStreamTable of
CISCO-USER-CONNECTION-TAP-MIB.
msPdsn: The specific filter is a Mobile Sub
connection filter with same indices as
that of this table. The exact filter
is a row in ccptapStreamTable of
CISCO-CDMA-PDSN-TAP-MIB.
mobility: The specific filter is a Mobile
Subscriber connection filter with same
indices as that of this table. The exact
filter is a row in cmtapStreamTable of
CISCO-MOBILITY-TAP-MIB.rw Enumeration .1.3.6.1.4.1.9.9.399.1.2.1.1.2 |
cTap2StreamInterceptEnableIf 'true', the tap should intercept matching traffic. The
value for this object should be set to 'true' only after an
additional filter specification has been attached to this
stream.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.399.1.2.1.1.3 |
cTap2StreamInterceptedPacketsThe number of packets matching this data stream specification
that have been intercepted.ro Counter .1.3.6.1.4.1.9.9.399.1.2.1.1.4 |
cTap2StreamInterceptDropsThe number of packets matching this data stream specification
that, having been intercepted, were dropped in the lawful
intercept process.ro Counter .1.3.6.1.4.1.9.9.399.1.2.1.1.5 |
cTap2StreamStatusThe status of this conceptual row. This object manages
creation, modification, and deletion of rows in this table.
cTap2StreamInterceptEnable may be modified any time even the
value of this entry rowStatus object is 'active'. When other
rows must be changed, cTap2StreamStatus must be first set to
'notInService'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.399.1.2.1.1.6 |
cTap2StreamInterceptedHCPacketsThe number of packets matching this data stream specification
that have been intercepted. This object is a 64-bit version of
cTap2StreamInterceptedPackets.ro --?? syntax is not convertable to SMIv1 Counter .1.3.6.1.4.1.9.9.399.1.2.1.1.7 |
cTap2StreamInterceptHCDropsThe number of packets matching this data stream specification
that, having been intercepted, were dropped in the lawful
intercept process. This object is a 64-bit version of
cTap2StreamInterceptDrops.ro --?? syntax is not convertable to SMIv1 Counter .1.3.6.1.4.1.9.9.399.1.2.1.1.8 |
cTap2DebugGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.1.3 |
cTap2DebugAgeThis object contains the duration in minutes for which an
entry in cTap2DebugTable is maintained by the implementing
device after which the entry is deleted. The management
station also has the option of deleting the entry itself
by setting cTap2DebugStatus.ro INTEGER .1.3.6.1.4.1.9.9.399.1.3.1 |
cTap2DebugMaxEntriesThis object contains the maximum number of debug messages
maintained by the implementing device at a time. If this
limit is crossed, most recent message will replace the
least recent message.ro INTEGER .1.3.6.1.4.1.9.9.399.1.3.2 |
cTap2DebugTableA table that contains Lawful Intercept debug messages
generated by the implementing device. This table is used
by ciscoTap2MediationDebug and ciscoTap2StreamDebug
notifications.
An entry in this table contains a debug message which is
regarding either a Mediation Device or a intercept stream
created by a Mediation Device. The Mediation device is
identified by cTap2DebugMediationId whose value is
that of cTap2MediationContentId of cTapMediationEntry.
The stream is identified by cTap2DebugMediationId and
cTap2DebugStreamId whose values are that of
cTap2MediationContentId and cTap2StreamIndex of
the corresponding cTap2StreamEntry.
Note that cTap2DebugStreamId may be zero for an entry,
in which case the debug message is regarding a Medation
Device.
Entries are added to this table via cTap2DebugStatus in
accordance with the RowStatus convention. SEQUENCE OF CTap2DebugEntry .1.3.6.1.4.1.9.9.399.1.3.3 |
cTap2DebugEntryA list of the debug messages. CTap2DebugEntry .1.3.6.1.4.1.9.9.399.1.3.3.1 |
cTap2DebugIndexIndex to the debug table. INTEGER .1.3.6.1.4.1.9.9.399.1.3.3.1.1 |
cTap2DebugMediationIdThe value of this object is that of cTap2MediationContentId
identifying an entry in cTap2MediationTable. Note this object
may contain a value for which an entry in cTap2MediationTable
does not exist. This happens when creation of an entry in
cTap2MediationTable fails and this debug message conveys more
detailed information regarding the failure.ro Gauge .1.3.6.1.4.1.9.9.399.1.3.3.1.2 |
cTap2DebugStreamIdThe value of this object is that of cTap2StreamIndex of an
entry in cTap2StreamTable. This object along with
cTap2DebugMediationId identifies an entry in cTap2StreamTable.
The value of this object may be zero, in which this debug
message is regarding a Mediation Device, but not a particular
stream. Note this object may contain a value for which an
entry in cTap2MediationTable does not exist. This happens
when creation of an entry in cTap2StreamTable fails.ro Gauge .1.3.6.1.4.1.9.9.399.1.3.3.1.3 |
cTap2DebugMessageA text string contains the debug message.ro SnmpAdminString -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.399.1.3.3.1.4 |
cTap2DebugStatusThe status of this conceptual row. A row in this table is
created by the implementing device. A management station cannot
modify any of the objects in this row, except deleting the row
by setting this object to 'destroy'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.399.1.3.3.1.5 |
cTap2DebugUserTableThe User Table lists information of all the users configured
in the system who are given permission by different Mediation
Devices to access Lawful Intercept CLIs.
This table will have dependancy on cTap2MediationTable. When
entry in cTap2MediationTable is deleted or moved to
'notInService', entries corresponding cTap2MediationContentId
in this table will be deleted. SEQUENCE OF CTap2DebugUserEntry .1.3.6.1.4.1.9.9.399.1.3.4 |
cTap2DebugUserEntryA conceptual row in the cTap2DebugUserTable. Each row
represents name of user on the router to whom Mediation Device
with CCCid represented by cTap2MediationContentId has given
access to Lawful Intercept commands and cTap2DebugUserTimeout
represents the time when the entry will expire. CTap2DebugUserEntry .1.3.6.1.4.1.9.9.399.1.3.4.1 |
cTap2DebugUserNameA human readable string representing the name of debug user
who will have access to Lawful Intercept commands. SnmpAdminString .1.3.6.1.4.1.9.9.399.1.3.4.1.1 |
cTap2DebugUserTimeoutThis object specifies the time at which the row will be
removed from the table by the system. The value of this object
is only effective when the value of corresponding instance of
cTap2DebugUserStatus is 'active'.rw DateAndTime -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.399.1.3.4.1.2 |
cTap2DebugUserStorageTypeThis object specifies the storage type of this conceptual row.
If it is set to 'nonVolatile', this entry can be saved into
non-volatile memory.rw StorageType -- Rsyntax INTEGER { -- other(1), -- volatile(2), -- nonVolatile(3), -- permanent(4), -- readOnly(5) -- } .1.3.6.1.4.1.9.9.399.1.3.4.1.3 |
cTap2DebugUserStatusThe status of this conceptual row. This object manages
creation, modification, and deletion of rows in this table.
cTap2DebugUserTimeout may be modified any time even when the
value of this entry rowStatus object is 'active'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.399.1.3.4.1.4 |
ciscoTap2MIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2 |
ciscoTap2MIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.1 |
ciscoTap2MIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.1.1 |
ciscoTap2MIBComplianceRev2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.1.2 |
ciscoTap2MIBComplianceRev3 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.1.3 |
ciscoTap2MIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2 |
ciscoTap2MediationComplianceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.1 |
ciscoTap2StreamComplianceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.2 |
ciscoTap2NotificationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.3 |
ciscoTap2MediationCpbComplianceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.4 |
ciscoTap2DebugComplianceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.5 |
ciscoTap2StreamHCStatsGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.6 |
ciscoTap2DebugComplianceGroupRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.399.2.2.7 |