CISCO-SONET-MIB
AI MIB Summary
The CISCO-SONET-MIB enables monitoring and management of SONET/SDH interface performance and fault conditions on Cisco hardware by extending standard RFC 2558 counters with vendor-specific objects. It tracks critical physical layer metrics such as signal loss, bit errors, and alarm states to facilitate precise troubleshooting of optical transport circuits.
The MIB module to describe SONET/SDH interfaces objects. This is an extension to the standard SONET MIB(RFC 2558).
124
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
124 total| Object Name |
|---|
ciscoSonetMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9.9.126 |
ciscoSonetMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.0 |
ciscoSonetSectionStatusChangeThis notification is generated whenever the value of
sonetSectionCurrentStatus changes. TRAP-TYPE .1.3.6.1.4.1.9.9.126.0.1 |
ciscoSonetLineStatusChangeThis notification is generated whenever the value of
sonetLineCurrentStatus changes. TRAP-TYPE .1.3.6.1.4.1.9.9.126.0.2 |
ciscoSonetPathStatusChangeThis notification is generated whenever the value of
sonetPathCurrentStatus changes. TRAP-TYPE .1.3.6.1.4.1.9.9.126.0.3 |
ciscoSonetVTStatusChangeThis notification is generated whenever the value of
sonetVTCurrentStatus changes. TRAP-TYPE .1.3.6.1.4.1.9.9.126.0.4 |
ciscoSonetMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1 |
csConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.1 |
csConfigTableThe SONET/SDH configuration table. This table has objects
for configuring sonet lines. SEQUENCE OF CsConfigEntry .1.3.6.1.4.1.9.9.126.1.1.1 |
csConfigEntryAn entry in the table. There is an entry for each SONET line
in the table. Entries are automatically created for an
ifType value of sonet(39). 'ifAdminStatus' from the ifTable
must be used to enable or disable a line. A line is in
disabled(down) state unless provisioned 'up' using
'ifAdminStatus'. CsConfigEntry .1.3.6.1.4.1.9.9.126.1.1.1.1 |
csConfigLoopbackTypeThis object specifies the desired loopback mode
configuration of the SONET line.
The possible values of this objects are follows:
noLoopback :
Not in the loopback state.
lineLocal :
The signal transmitted from this interface
is connected to the associated incoming
receiver. This ensures that the SONET frame
transmitted from the interface is received back
at the interface.
lineRemote :
The signal received at the interface is looped
back out to the associated transmitter.
This ensures that the remote equipment that
originated the signal receives it back. The
signal may undergo degradation as a result of
the characteristics of the transmission
medium.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.1 |
csConfigXmtClockSourceSpecifies the source of the transmit clock.
loopTiming: indicates that the recovered receive
clock is used as the transmit clock.
localTiming: indicates that a local clock source is
used or that an external clock is
attached to the box containing the
interface.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.2 |
csConfigFrameScrambleThis object is used to disable or enable the Scrambling
option in SONET line.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.3 |
csConfigTypeThis object represents the configured line type.
Sts is SONET format. Stm is SDH format.
sonetSts3c : OC3 concatenated
sonetStm1 : European standard OC3
sonetSts12c : OC12 concatenated
sonetStm4 : European standard OC12
sonetSts48c : OC48 concatenated
sonetStm16 : European standard OC48
sonetSts192c : OC-192 concatenated
sonetStm64 : European standard OC-192
sonetSts3 : OC3 (unconcatenated)ro Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.4 |
csConfigRDIVTypeThis object specifies the type of RDI-V (Remote Defect
Indication - Virtual Tributary/Container) sent by this
Network Element (NE) to the remote Network Element.
onebit : use 1 bit RDI-V
threebit : use 3 bit enhanced RDI-V.
Default is onebit.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.5 |
csConfigRDIPTypeThis object represents the type of RDI-P (Remote Defect
Indication - Path) sent by this Network Element (NE)
to remote Network Element.
onebit : use 1 bit RDI-P
threebit : use 3 bit enhanced RDI-P.
Default is onebit.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.1.1.6 |
csVTConfigTableThis table contains objects to configure the VT/VC (Virtual
Tributary / Virtual Container) related properties of
SONET/SDH lines. SEQUENCE OF CsVTConfigEntry .1.3.6.1.4.1.9.9.126.1.1.2 |
csVTConfigEntryThere is an entry in this table for each SONET line that
supports SONET virtual tributaries or SDH virtual containers.
Each entry in this table will have a corresponding entry
in csConfigTable. CsVTConfigEntry .1.3.6.1.4.1.9.9.126.1.1.2.1 |
csTributaryTypeType of the tributary carried within the SONET/SDH signal.
vt15vc11 : carries T1 signal
vt2vc12 : carries E1 signalrw Enumeration .1.3.6.1.4.1.9.9.126.1.1.2.1.1 |
csTributaryMappingTypeThis object represents the VT/VC mapping type.
asynchronous: In this mode, the channel structure of
DS1/E1 is neither visible nor preserved.
byteSynchronous: In this mode, the DS0 signals inside the
VT/VC can be found and extracted from the
frame.
Default is asynchronous(1).rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.2.1.2 |
csTributaryFramingTypeThis object represents the framing type to be assigned to the
virtual tributaries in byte sync mapping mode.
notApplicable : If VT mapping is not byteSynchronous(2).
dsx1ESF : Extended Superframe Format
dsx1D4 : Superframe Format
Default is dsx1ESF(3) if csTributaryMappingType is
byteSynchronous(2). For asynchronous(1) mapping, the default is
notApplicable(1).
The value notApplicable(1) can not be set.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.2.1.3 |
csSignallingTransportModeThis object represents the mode used to transport DS0
signalling information for T1 byteSynchronous mapping (GR253).
In signallingTransferMode(2), the robbed-bit signalling is
transferred to the VT header. In clearMode(3), only the
framing bit is transferred to the VT header.
Default is signallingTransferMode(2) if csTributaryMappingType
is byteSynchronous. For asynchronous mapping, it is
notApplicable(1).
The value notApplicable(1) can not be set.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.2.1.4 |
csTributaryGroupingTypeThis object represents the method used to group VCs into an
STM-1 signal. Applicable only to SDH.
au3Grouping: STM1<-AU-3<-TUG-2<-TU-12<-VC12 or
STM1<-AU-3<-TUG-2<-TU-11<-VC11.
au4Grouping: STM1<-AU-4<-TUG-3<-TUG-2<-TU-12<-VC12 or
STM1<-AU-4<-TUG-3<-TUG-2<-TU-11<-VC11.
Default is au3Grouping(2) for SDH and notApplicable(1) for SONET.rw Enumeration .1.3.6.1.4.1.9.9.126.1.1.2.1.5 |
csApsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.2 |
csApsConfigTableThis table contains objects to configure APS
(Automatic Protection Switching) feature in a SONET
Line. APS is the ability to configure a pair of SONET
lines for redundancy so that the hardware will
automatically switch the active line from working line
to the protection line or vice versa, within 60ms,
when the active line fails. SEQUENCE OF CsApsConfigEntry .1.3.6.1.4.1.9.9.126.1.2.1 |
csApsConfigEntryAn entry is created when an APS pair is configured.
To create an entry, the following objects must be
specified:
csApsWorkingIndex, csApsProtectionIndex, csApsEnable,
csApsArchMode. The protection line must not be active,
i.e, ifAdminStatus must be 'down', while configuring
APS. An entry is created by setting the value of
'csApsEnable' to csApsEnabled (2) and deleted by
setting it to csApsDisabled (1). Once a line is
configured as working line or protection line, it
remains in that role until APS is disabled on that
sonet line pair. It remains in the working/protection
role even after the card is reset. CsApsConfigEntry .1.3.6.1.4.1.9.9.126.1.2.1.1 |
csApsWorkingIndexWhen a pair of APS lines is configured, one line has
to be the working line, which is the primary line,
and the other has to be the protection line, which
is the backup line. This object refers to the working line
in the APS pair. For G.783 AnnexB, this index refers to
Working Section 1. InterfaceIndex -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.126.1.2.1.1.1 |
csApsProtectionIndexThe protection line indicates that it will become
the active line when an APS switch occurs (APS switch
could occur because of a failure on the working line).
For G.783 AnnexB, This index refers to Working Section
2.rw InterfaceIndex -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.126.1.2.1.1.2 |
csApsEnableThis object is used to enable or disable the APS feature
on the working/protection line pairs. When enabled,
the hardware will automatically switch the active line
from the working line to the protection line within 60ms,
or vice versa.rw Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.3 |
csApsArchModeThis object is used to configure APS architecture mode
on the working/protection line pairs.
All of the following are supported on single slot.
oneToOne(2) is not supported across 2 slots,i.e. the
working and protection slot numbers must be the same in
oneToOne(2).
onePlusOne : This can be supported on the same card
and across 2 cards.
This mode means that the transmit and receive signals
go only over the active line(which could be working or
protection line). (straight cable implied)
oneToOne : This is supported only on the same card
This mode means that the transmit and receive signals
go over the working and protection lines.
(straight cable implied)
anexBOnePlusOne : This can be supported on the same card
and across 2 cards.
This mode is like the onePlusOne mode, except that the
'csApsDirection' can only be bi-directional.
(straight cable implied)
ycableOnePlusOneNok1k2: With Y-cable ignore K1K2 bytes.
This mode is the Y-cable redundancy mode.
straightOnePlusOneNok1k2 : With straight cable, ignore
K1K2 bytes. This mode is like
onePlusOne, but with K1, K2
bytes ignored.rw Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.4 |
csApsActiveLineThis object indicates which line is currently active.
It could be the working line(Section 1 for Annex B),
the protection line(Section 2 for Annex B) or none
if neither working nor protection line is active.
This object reflects the status of receive direction.ro Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.5 |
csApsSigFaultBERThis object contains the Bit Error Rate threshold for
Signal Fault detection on the working line. Once this
threshold is exceeded, an APS switch will occur.
This value is 10 to the -n, where n is between 3 and 5.rw Gauge .1.3.6.1.4.1.9.9.126.1.2.1.1.6 |
csApsSigDegradeBERThis object contains the Bit Error Rate threshold for
Signal Degrade detection on the working line. Once this
threshold is exceeded, an APS switch will occur.
This value is 10 to -n where n is between 5 and 9.rw Gauge .1.3.6.1.4.1.9.9.126.1.2.1.1.7 |
csApsWaitToRestoreThis object contains interval in minutes to wait
before attempting to switch back to working line.
Not applicable if the line is configured in
non-revertive mode, i.e. protection line will
continue to be active, even if failures on the
working line are cleared. The framer clears the
signal-fault and signal-degrade when APS switch
occurs. Please refer to 'csApsRevertive' for
description of non-revertive.rw Gauge .1.3.6.1.4.1.9.9.126.1.2.1.1.8 |
csApsDirectionThis object is used to configure the switching
direction which this APS line supports.
Unidirectional : APS switch only in one direction.
Bidirectional : APS switch in both ends of the line.rw Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.9 |
csApsRevertiveThis object is used to configure the APS revertive or
nonrevertive option.
revertive :
Will switch the working line back to active state after
the Wait-To-restore interval has expired and the
working line Signal-Fault/Signal-Degrade has been
cleared. Please refer to 'csApsWaitToRestore' for
description of Wait-To-Restore interval.
nonrevertive :
The protection line continues to be the active line,
The active line does not switch to the working line.rw Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.10 |
csApsDirectionOperationalThis object shows the actual APS direction that is
implemented on the Near End terminal. APS direction
configured through csApsDirection is negotiated with
the Far End and APS direction setting acceptable to
both ends is operational at the Near End.ro Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.11 |
csApsArchModeOperationalThis object shows the actual APS architecture mode that
is implemented on the Near End terminal. APS architecture
mode configured through csApsArchMode object is
negotiated with the Far End through APS channel.
Architecture mode acceptable to both the Near End and
the Far End terminals is then operational at the Near
End. This value can be different than the APS
Architecture mode configured.ro Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.12 |
csApsChannelProtocolThis object allows to configure APS channel protocol to
be implemented at Near End terminal.
K1 and K2 overhead bytes in a SONET signal are used as
an APS channel.
This channel is used to carry APS protocol.
Possible values:
bellcore(1) : Implements APS channel protocol as defined
in bellcore document GR-253-CORE.
itu(2) : Implements APS channel protocol as defined in
ITU document G.783.rw Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.13 |
csApsFailureStatusThis object indicates APS line failure status.ro CsApsLineFailureStatus -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.126.1.2.1.1.14 |
csApsSwitchReasonThis object indicates APS line switch reason.ro CsApsLineSwitchReason -- Rsyntax INTEGER { -- csApsOther(1), -- csApsRevertive(2), -- csApsManual(3), -- csApsSignalDefectLow(4), -- csApsSignalDefectHigh(5), -- csApsSignalFailureLow(6), -- csApsSignalFailureHigh(7), -- csApsForceSwitch(8), -- csApsLockOut(9), -- csApsNoSwitch(10) -- } .1.3.6.1.4.1.9.9.126.1.2.1.1.15 |
csApsPrimarySectionThis object indicates which working section is the APS
primary section. In G.783 AnnexB, the K1/K2 Bytes are
received on the secondary Section. All the Switch
Requests are for a switch from the primary section to
the secondary section. The object csApsActiveline will
indicate which section is currently carrying the
traffic. Once the switch request clears normally,
traffic is maintained on the section to which it was
switched by making that section the primary section.
Possible values:
workingSection1(1): Working Section 1 is Primary Section
workingSection2(2): Working Section 2 is Primary Section
none(3) : none.ro Enumeration .1.3.6.1.4.1.9.9.126.1.2.1.1.16 |
csApsLineFailureCodeThe object indicates the APS line failure code. This is the
failure encountered by the APS line.
Refer to CsApsLineFailureCode TC for failure code definitions.
The object is used for notifications.ro CsApsLineFailureCode -- Rsyntax INTEGER { -- csApsChannelMismatch(1), -- csApsProtectionByteFail(2), -- csApsFEProtectionFailure(3), -- csApsModeMismatch(4) -- } .1.3.6.1.4.1.9.9.126.1.2.2 |
csApsLineSwitchReasonThis object indicates the APS line switch reason.
When the working line on one end fails, its other end
is told to do an APS switch.
Refer to CsApsLineSwitchReason TC for more information.
The object is used for notifications.ro CsApsLineSwitchReason -- Rsyntax INTEGER { -- csApsOther(1), -- csApsRevertive(2), -- csApsManual(3), -- csApsSignalDefectLow(4), -- csApsSignalDefectHigh(5), -- csApsSignalFailureLow(6), -- csApsSignalFailureHigh(7), -- csApsForceSwitch(8), -- csApsLockOut(9), -- csApsNoSwitch(10) -- } .1.3.6.1.4.1.9.9.126.1.2.3 |
csSection OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.3 |
cssTotalTableThe SONET/SDH Section Total table. It contains the
cumulative sum of the various statistics for the 24 hour
period preceding the current interval. The object
'sonetMediumValidIntervals' from RFC2558 contains the
number of 15 minute intervals that have elapsed since
the line is enabled. SEQUENCE OF CssTotalEntry .1.3.6.1.4.1.9.9.126.1.3.1 |
cssTotalEntryAn entry in the SONET/SDH Section Total table. Entries
are created automatically for sonet lines. CssTotalEntry .1.3.6.1.4.1.9.9.126.1.3.1.1 |
cssTotalESsThe number of Errored Seconds encountered by a SONET/SDH
Section in the last 24 hours.ro Gauge -- Units -- errored seconds .1.3.6.1.4.1.9.9.126.1.3.1.1.1 |
cssTotalSESsThe number of Severely Errored Seconds encountered by a
SONET/SDH Section in the last 24 hours.ro Gauge -- Units -- severely errored seconds .1.3.6.1.4.1.9.9.126.1.3.1.1.2 |
cssTotalSEFSsThe number of Severely Errored Framing Seconds
encountered by a SONET/SDH Section in the last 24 hours.ro Gauge -- Units -- severely errored framing seconds .1.3.6.1.4.1.9.9.126.1.3.1.1.3 |
cssTotalCVsThe number of Coding Violations encountered by a
SONET/SDH Section in the last 24 hours.ro Gauge -- Units -- coding violations .1.3.6.1.4.1.9.9.126.1.3.1.1.4 |
cssTraceTableThe SONET/SDH Section Trace table. This table contains
objects for tracing the sonet section. SEQUENCE OF CssTraceEntry .1.3.6.1.4.1.9.9.126.1.3.2 |
cssTraceEntryAn entry in the trace table. Entries exist for active sonet
lines. The objects in this table are used to verify
continued connection between the two ends of the line. CssTraceEntry .1.3.6.1.4.1.9.9.126.1.3.2.1 |
cssTraceToTransmitSonet Section Trace To Transmit. This is string that
is transmitted to perform Sonet section trace
diagnostics. The trace string is repetitively
transmited so that a trace receiving terminal can
verify its continued connection to the intended
transmitter. The default value is a zero-length string.
Unless this object is set to a non-zero length string,
tracing will not be performed.rw OCTET STRING .1.3.6.1.4.1.9.9.126.1.3.2.1.1 |
cssTraceToExpectSonet Section Trace To Expect. The receiving terminal
verifies if the incoming string matches this string.
The value of 'cssTraceFailure' indicates whether a
trace mismatch occurred. The default value is a
zero-length string.rw OCTET STRING .1.3.6.1.4.1.9.9.126.1.3.2.1.2 |
cssTraceFailureThe value of this object is set to 'true' when Sonet
Section received trace does not match the
'cssTraceToExpect'.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.126.1.3.2.1.3 |
cssTraceReceivedThis object is used to view the Sonet Section Trace that
is received by the receiving terminal.ro OCTET STRING .1.3.6.1.4.1.9.9.126.1.3.2.1.4 |
csLine OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.4 |
cslTotalTableThe SONET/SDH Line Total table. It contains the
cumulative sum of the various statistics for the 24
hour period preceding the current interval. The object
'sonetMediumValidIntervals' from RFC2558 contains the
number of 15 minute intervals that have elapsed since
the line is enabled. SEQUENCE OF CslTotalEntry .1.3.6.1.4.1.9.9.126.1.4.1 |
cslTotalEntryAn entry in the SONET/SDH Line Total table. Entries
are created automatically for sonet lines. CslTotalEntry .1.3.6.1.4.1.9.9.126.1.4.1.1 |
cslTotalESsThe number of Errored Seconds encountered by a SONET/SDH
Line in the last 24 hours.ro Gauge -- Units -- errored seconds .1.3.6.1.4.1.9.9.126.1.4.1.1.1 |
cslTotalSESsThe number of Severely Errored Seconds encountered by a
SONET/SDH Line in the last 24 hours.ro Gauge -- Units -- severely errored seconds .1.3.6.1.4.1.9.9.126.1.4.1.1.2 |
cslTotalCVsThe number of Coding Violations encountered by a
SONET/SDH Line in the last 24 hours.ro Gauge -- Units -- coding violations .1.3.6.1.4.1.9.9.126.1.4.1.1.3 |
cslTotalUASsThe number of Unavailable Seconds encountered by a
SONET/SDH Line in the last 24 hours.ro Gauge -- Units -- unavailable seconds .1.3.6.1.4.1.9.9.126.1.4.1.1.4 |
cslFarEndTotalTableThe SONET/SDH Far End Line Total table. It contains the
cumulative sum of the various statistics for the 24 hour
period preceding the current interval. The object
'sonetMediumValidIntervals' from RFC2558 contains the
number of 15 minute intervals that have elapsed since the
line is enabled. SEQUENCE OF CslFarEndTotalEntry .1.3.6.1.4.1.9.9.126.1.4.2 |
cslFarEndTotalEntryAn entry in the SONET/SDH Far End Line Total table. Entries
are created automatically for sonet lines. CslFarEndTotalEntry .1.3.6.1.4.1.9.9.126.1.4.2.1 |
cslFarEndTotalESsThe number of Errored Seconds encountered by a SONET/SDH Far
End Line in the last 24 hours.ro Gauge -- Units -- errored seconds .1.3.6.1.4.1.9.9.126.1.4.2.1.1 |
cslFarEndTotalSESsThe number of Severely Errored Seconds encountered by a
SONET/SDH Far End Line in the last 24 hours.ro Gauge -- Units -- severely errored seconds .1.3.6.1.4.1.9.9.126.1.4.2.1.2 |
cslFarEndTotalCVsThe number of Coding Violations encountered by a SONET/SDH
Far End Line in the last 24 hours.ro Gauge -- Units -- coding violations .1.3.6.1.4.1.9.9.126.1.4.2.1.3 |
cslFarEndTotalUASsThe number of Unavailable Seconds encountered by a
SONET/SDH Far End Line in the last 24 hours.ro Gauge -- Units -- unavailable seconds .1.3.6.1.4.1.9.9.126.1.4.2.1.4 |
csPath OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.5 |
cspTotalTableThe SONET/SDH Path Total table. It contains the cumulative
sum of the various statistics for the 24 hour period
preceding the current interval.The object
'sonetMediumValidIntervals' from RFC2558 contains the number
of 15 minute intervals that have elapsed since the line is
enabled. SEQUENCE OF CspTotalEntry .1.3.6.1.4.1.9.9.126.1.5.1 |
cspTotalEntryAn entry in the SONET/SDH Path Total table. Entries
are created automatically for sonet lines. CspTotalEntry .1.3.6.1.4.1.9.9.126.1.5.1.1 |
cspTotalESsThe number of Errored Seconds encountered by a SONET/SDH
Path in the last 24 hours.ro Gauge -- Units -- errored seconds .1.3.6.1.4.1.9.9.126.1.5.1.1.1 |
cspTotalSESsThe number of Severely Errored Seconds encountered by a
SONET/SDH Path in the last 24 hours.ro Gauge -- Units -- severely errored seconds .1.3.6.1.4.1.9.9.126.1.5.1.1.2 |
cspTotalCVsThe number of Coding Violations encountered by a
SONET/SDH Path in the last 24 hours.ro Gauge -- Units -- coding violations .1.3.6.1.4.1.9.9.126.1.5.1.1.3 |
cspTotalUASsThe number of Unavailable Seconds encountered by a
SONET/SDH Path in the last 24 hours.ro Gauge -- Units -- unavailable seconds .1.3.6.1.4.1.9.9.126.1.5.1.1.4 |
cspFarEndTotalTableThe SONET/SDH Far End Path Total table. Far End is the
remote end of the line. The table contains the cumulative
sum of the various statistics for the 24 hour period
preceding the current interval. The object
'sonetMediumValidIntervals' from RFC2558 contains the
number of 15 minute intervals that have elapsed since
the line is enabled. SEQUENCE OF CspFarEndTotalEntry .1.3.6.1.4.1.9.9.126.1.5.2 |
cspFarEndTotalEntryAn entry in the SONET/SDH Far End Path Total table.
Entries are created automatically for sonet lines. CspFarEndTotalEntry .1.3.6.1.4.1.9.9.126.1.5.2.1 |
cspFarEndTotalESsThe number of Errored Seconds encountered by a SONET/SDH
far end path in the last 24 hours.ro Gauge -- Units -- errored seconds .1.3.6.1.4.1.9.9.126.1.5.2.1.1 |
cspFarEndTotalSESsThe number of Severely Errored Seconds encountered by a
SONET/SDH far end path in the last 24 hours.ro Gauge -- Units -- severely errored seconds .1.3.6.1.4.1.9.9.126.1.5.2.1.2 |
cspFarEndTotalCVsThe number of Coding Violations encountered by a
SONET/SDH far end path in the last 24 hours.ro Gauge -- Units -- coding violations .1.3.6.1.4.1.9.9.126.1.5.2.1.3 |
cspFarEndTotalUASsThe number of Unavailable Seconds encountered by a
SONET/SDH far end path in the last 24 hours.ro Gauge -- Units -- unavailable seconds .1.3.6.1.4.1.9.9.126.1.5.2.1.4 |
cspTraceTableThe SONET/SDH Path Trace table. This table contains objects
for tracing the sonet path. SEQUENCE OF CspTraceEntry .1.3.6.1.4.1.9.9.126.1.5.3 |
cspTraceEntryAn entry in the SONET/SDH Path Trace table. The entries
exist for active sonet lines. The objects in this table are
used to verify continued connection between the two ends of
the line. CspTraceEntry .1.3.6.1.4.1.9.9.126.1.5.3.1 |
cspTraceToTransmitSonet Path Trace To Transmit. The trace string is
repetitively transmited so that a trace receiving terminal
can verify its continued receiving terminal can verify its
continued connection to the intended transmitter. The
default value is a zero-length string. Unless this object
is set to a non-zero length string, tracing will not be
performed.rw OCTET STRING .1.3.6.1.4.1.9.9.126.1.5.3.1.1 |
cspTraceToExpectSonet Path Trace To Expect. The receiving terminal verifies
if the incoming string matches this string. The value of
'cspTraceFailure' indicates whether a trace mismatch
occured. The default value is a zero-length string.rw OCTET STRING .1.3.6.1.4.1.9.9.126.1.5.3.1.2 |
cspTraceFailureThe value of this object is set to 'true' when Sonet Path
received trace does not match the 'cspTraceToExpect'.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.126.1.5.3.1.3 |
cspTraceReceivedThis object is used to view the Sonet Path Trace that is
received by the receiving terminal.ro OCTET STRING .1.3.6.1.4.1.9.9.126.1.5.3.1.4 |
csStats OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.6 |
csStatsTableThe SONET/SDH Section statistics table. This table
maintains the number of times the line encountered Loss of
Signal(LOS), Loss of frame(LOF), Alarm Indication
signals(AISs), Remote failure indications(RFIs). SEQUENCE OF CsStatsEntry .1.3.6.1.4.1.9.9.126.1.6.1 |
csStatsEntryAn entry in the SONET/SDH statistics table. These are
realtime statistics for the Sonet section, line and path
layers. The statistics are gathered for each sonet line.
An entry is created automatically and is indexed by
ifIndex. CsStatsEntry .1.3.6.1.4.1.9.9.126.1.6.1.1 |
cssLOSsThe number of Loss of signals(LOS) encountered by a
SONET/SDH Section. A high value for this object may
indicate a problem with the Sonet Section layer.ro Counter -- Units -- loss of signals .1.3.6.1.4.1.9.9.126.1.6.1.1.1 |
cssLOFsThe number of Loss of Frames (LOF) encountered by a
SONET/SDH Section. A high value for this object may
indicate a problem with the Sonet Section layer.ro Counter -- Units -- loss of frames .1.3.6.1.4.1.9.9.126.1.6.1.1.2 |
cslAISsThe number of alarm indication signals(AIS) encountered by
a SONET/SDH Line. A high value for this object may indicate a
problem with the Sonet Line layer.ro Counter -- Units -- alarm indication signals .1.3.6.1.4.1.9.9.126.1.6.1.1.3 |
cslRFIsThe number of remote failure indications (RFI) encountered
by a SONET/SDH Line. A high value for this object may
indicate a problem with the Sonet Line layer.ro Counter -- Units -- remote failure indications .1.3.6.1.4.1.9.9.126.1.6.1.1.4 |
cspAISsThe number of alarm indication signals (AIS) encountered
by a SONET/SDH Path. A high value for this object may
indicate a problem with the Sonet Path layer.ro Counter -- Units -- alarm indication signals .1.3.6.1.4.1.9.9.126.1.6.1.1.5 |
cspRFIsThe number of remote failure indications (RFI)
encountered by a SONET/SDH Path. A high value for this
object may indicate a problem with the Sonet Path layer.ro Counter -- Units -- remote failure indications .1.3.6.1.4.1.9.9.126.1.6.1.1.6 |
cspConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.7 |
cspConfigTableCisco extension to SONET Path current table. SEQUENCE OF CspConfigEntry .1.3.6.1.4.1.9.9.126.1.7.1 |
cspConfigEntryAn entry in Cisco extension to the SONET path current table. CspConfigEntry .1.3.6.1.4.1.9.9.126.1.7.1.1 |
cspSonetPathPayloadSpecifies the payload carried by the SONET/SDH Path.
The payload specification corresponds to C2 (Signal Label)
overhead byte in SONET/SDH Path Overhead:
unequipped(1) : Path is not provisioned to carry any payload.
unspecified(2): Path is carrying an unspecifed payload.
ds3(3) : Path is carrying a DS3 path as payload.
vt15vc11(4) : Path is carrying SONET-VT1.5/SDH-VC11 payload.
vt2vc12(5) : Path is carrying SONET-VT2/SDH-VC12 as payload.
atmCell(6) : Path is carrying ATM Cells as payload.
hdlcFr(7) : Path is carrying Frame Relay (HDLC) payload.
A write operation on this object will result in update to
C2 overhead byte in the Path Overhead.rw Enumeration .1.3.6.1.4.1.9.9.126.1.7.1.1.1 |
csNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.1.8 |
csNotificationsEnabledThis object controls if the generation of
ciscoSonetSectionStatusChange, ciscoSonetLineStatusChange,
ciscoSonetPathStatusChange and ciscoSonetVTStatusChange
notifications is enabled. If the value of this object
is 'true(1)', then all notifications in this MIB are
enabled; otherwise they are disabled.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.126.1.8.1 |
ciscoSonetMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3 |
ciscoSonetMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.1 |
ciscoSonetMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.1.1 |
ciscoSonetMIBCompliance1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.1.2 |
ciscoSonetMIBCompliance2 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.1.3 |
ciscoSonetMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2 |
ciscoSonetConfMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.1 |
ciscoSonetStatsMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.2 |
ciscoSonetTraceMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.3 |
ciscoSonetApsMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.4 |
ciscoSonetApsMIBGroup1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.5 |
ciscoSonetConfMIBGroup1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.6 |
ciscoSonetVTConfMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.7 |
ciscoSonetPathConfMIBGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.8 |
ciscoSonetNotifEnableGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.9 |
ciscoSonetSectionNotifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.10 |
ciscoSonetLineNotifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.11 |
ciscoSonetPathNotifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.12 |
ciscoSonetVTNotifGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.126.3.2.13 |