CISCO-PRIVATE-VLAN-MIB
AI MIB Summary
The CISCO-PRIVATE-VLAN-MIB enables monitoring and management of Private VLAN (PVLAN) configurations, including primary, isolated, and community VLAN associations, on Cisco switching devices via SNMP. It exposes specific metrics for PVLAN port states, VLAN membership, and isolation domain status to facilitate granular traffic segmentation verification and troubleshooting.
The MIB module to support Private VLAN feature on Cisco's switching devices.
58
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
58 total| Object Name |
|---|
ciscoPrivateVlanMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173 |
IF-MIB Unknown .1.3.6.1.4.1.9.9.173 |
cpvlanMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.1 |
cpvlanVlanObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.1.1 |
cpvlanVlanTableA table containing Private VLAN information on the
VLANs which currently exist. SEQUENCE OF CpvlanVlanEntry .1.3.6.1.4.1.9.9.173.1.1.1 |
cpvlanVlanEntryA conceptual row containing the Private VLAN
information on the VLANs for a particular management
domain. CpvlanVlanEntry .1.3.6.1.4.1.9.9.173.1.1.1.1 |
cpvlanVlanPrivateVlanTypeIndicated the VLAN type as defined for Private VLAN
feature.ro PrivateVlanType -- Rsyntax INTEGER { -- normal(1), -- primary(2), -- isolated(3), -- community(4), -- twoWayCommunity(5) -- } .1.3.6.1.4.1.9.9.173.1.1.1.1.1 |
cpvlanVlanAssociatedPrimaryVlanThe VLAN ID of The associated primary VLAN used for
the Private VLAN feature if cpvlanVlanPrivateVlanType
has the value of isolated(3), community(4) or
twoWayCommunity(5). If cpvlanVlanPrivateVlanType
has the value of normal(1) or primary(2), then this
object has the value of 0.
Note that one isolated VLAN can only be associated with
one unique primary VLAN. One primary VLAN can only be
associated with one isolated VLAN.
One primary VLAN can be associated with multiple VLANs
of community or twoWayCommunity type; one community
or twoWayCommunity VLAN can only be associated with one
unique primary VLAN.ro VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.1.1.1.2 |
cpvlanVlanEditTableA table containing Private VLAN information on the VLANs
in the VLAN Edit Buffer for a particular management
domain. SEQUENCE OF CpvlanVlanEditEntry .1.3.6.1.4.1.9.9.173.1.1.2 |
cpvlanVlanEditEntryA conceptual row containing the Private VLAN information
on the VLANs in the VLAN Edit Buffer for a particular
management domain. CpvlanVlanEditEntry .1.3.6.1.4.1.9.9.173.1.1.2.1 |
cpvlanVlanEditPrivateVlanTypeThe VLAN type as defined for Private VLAN feature.
Note that a VLAN's Private VLAN type can not be
changed once it already has any ports in it.rw PrivateVlanType -- Rsyntax INTEGER { -- normal(1), -- primary(2), -- isolated(3), -- community(4), -- twoWayCommunity(5) -- } .1.3.6.1.4.1.9.9.173.1.1.2.1.1 |
cpvlanVlanEditAssocPrimaryVlanThe VLAN ID of the associated primary VLAN used for
the Private VLAN feature if
cpvlanVlanEditPrivateVlanType has the value of
isolated(3), community(4), twoWayCommunity(5). If
cpvlanVlanEditPrivateVlanType has the value of normal(1)
or primary(2), then this object has the value of 0.
Note that one isolated VLAN can only be associated
with one unique primary VLAN. One primary VLAN can only
be associated with one isolated VLAN.
One primary VLAN can be associated with multiple VLANs
of community or twoWayCommunity type; one community
or twoWayCommunity VLAN can only be associated with one
unique primary VLAN.rw VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.1.2.1.2 |
cpvlanPortObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.1.2 |
cpvlanPrivatePortTableA table containing information of the configuration of
secondary VLAN on the ports of the device. SEQUENCE OF CpvlanPrivatePortEntry .1.3.6.1.4.1.9.9.173.1.2.1 |
cpvlanPrivatePortEntryA conceptual row containing information of the
configuration of secondary VLAN for each port. An entry
is created by the managed system for each interface which
can be configured as a private port for Private VLAN
feature. CpvlanPrivatePortEntry .1.3.6.1.4.1.9.9.173.1.2.1.1 |
cpvlanPrivatePortSecondaryVlanThe VLAN ID of the secondary VLAN configured on this
private port. A private port is a port that allows
the ingress traffic of the secondary VLAN as well as
egress traffic of its associated primary VLAN, but
blocks the egress traffic of the isolated VLAN while
allowing the egress traffic of the community
or twoWayCommunity VLAN depending on the type of the
secondary VLAN.
Note that a port can join a secondary VLAN only after
this secondary VLAN has been associated with a primary
VLAN, i.e., the cpvlanVlanAssociatedPrimaryVlan has a
non-zero value. The default value of 0 for this object
means this port has not joined any secondary VLAN yet.rw VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.2.1.1.1 |
cpvlanPromPortTableA table containing information of secondary VLAN to
primary VLAN remapping on ports of the device. SEQUENCE OF CpvlanPromPortEntry .1.3.6.1.4.1.9.9.173.1.2.2 |
cpvlanPromPortEntryA conceptual row containing information of secondary
VLAN to primary VLAN remapping for each port. An entry
is created by the managed system for each interface
which can be configured as a promiscuous port for
Private VLAN feature. CpvlanPromPortEntry .1.3.6.1.4.1.9.9.173.1.2.2.1 |
cpvlanPromPortMultiPrimaryVlanIndicates whether all the bits set as secondary VLANs
in the corresponding remapping objects (i.e.
cpvlanPromPortSecondaryRemap,
cpvlanPromPortSecondaryRemap2k,
cpvlanPromPortSecondaryRemap3k,
cpvlanPromPortSecondaryRemap4k) can belong to multiple
primary VLANs or not for this port. If this object value
is false(2), then the object values of
cpvlanVlanAssociatedPrimaryVlan for the secondary VLANs
with their bits turned on as '1' in those remapping
objects must be the same. If this object value is
true(1), then the object values of
cpvlanVlanAssociatedPrimaryVlan for the secondary VLANs
with their bits turned on as '1' in those remapping
objects need not be the same.
A promiscuous port can remap a secondary VLAN to its
associated primary VLAN for egress traffic on the fly
as defined for Private VLAN feature.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.173.1.2.2.1.1 |
cpvlanPromPortSecondaryRemapA string of octets containing one bit per VLAN in the
management domain on this port. The first octet
corresponds to VLANs with VlanIndexOrZero values of 0
through 7; the second octet to VLANs 8 through 15; etc.
The most significant bit of each octet corresponds to
the lowest value VlanIndexOrZero in that octet.
A bit can only be set to '1' when the bit is
corresponding to a VLAN of Private VLAN isolated,
community or twoWayCommunity type which has already
been associated with a primary VLAN. Setting this bit
to '1' makes this promiscuous port remap the secondary
VLAN to its associated primary VLAN for egress traffic
on the fly, or remap the associated primary VLAN to
the secondary VLAN if the secondary VLAN is of
twoWayCommunity type and the object value of
cpvlanPromPortTwoWayRemapCapable for this promiscuous
port is true(1).
Note that if the length of this string is less than
128 octets, any 'missing' octets are assumed to contain
the value zero. An NMS may omit any zero-valued octets
from the end of this string in order to reduce SetPDU
size, and the agent may also omit zero-valued trailing
octets, to reduce the size of GetResponse PDUs.rw OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.2.1.2 |
cpvlanPromPortSecondaryRemap2kA string of octets containing one bit per VLAN for
VLANs with VlanIndexOrZero values of 1024 through 2047
in the management domain on this port. The first octet
corresponds to VLANs with VlanIndexOrZero values of 1024
through 1031; the second octet to VLANs 1032 through
1039; etc. The most significant bit of each octet
corresponds to the lowest value VlanIndexOrZero in
that octet.
A bit can only be set to '1' when the bit is
corresponding to a VLAN of Private VLAN isolated or
community type which has already been associated with a
primary VLAN. Setting this bit to '1' makes this
promiscuous port remap the secondary VLAN to its
associated primary VLAN for egress traffic on the fly,
or remap the associated primary VLAN to the secondary
VLAN if the secondary VLAN is of twoWayCommunity type
and the object value of cpvlanPromPortTwoWayRemapCapable
for this promiscuous port is true(1).
Note that if the length of this string is less than
128 octets, any 'missing' octets are assumed to contain
the value zero. An NMS may omit any zero-valued octets
from the end of this string in order to reduce SetPDU
size, and the agent may also omit zero-valued trailing
octets, to reduce the size of GetResponse PDUs.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.2.1.3 |
cpvlanPromPortSecondaryRemap3kA string of octets containing one bit per VLAN for
VLANs with VlanIndexOrZero values of 2048 through 3071
in the management domain on this port. The first octet
corresponds to VLANs with VlanIndexOrZero values of 2048
through 2055; the second octet to VLANs 2056 through
2063; etc. The most significant bit of each octet
corresponds to the lowest value VlanIndexOrZero in
that octet.
A bit can only be set to '1' when the bit is
corresponding to a VLAN of Private VLAN isolated or
community type which has already been associated with a
primary VLAN. Setting this bit to '1' makes this
promiscuous port remap the secondary VLAN to its
associated primary VLAN for egress traffic on the fly,
or remap the associated primary VLAN to the secondary
VLAN if the secondary VLAN is of twoWayCommunity type
and the object value of cpvlanPromPortTwoWayRemapCapable
for this promiscuous port is true(1).
Note that if the length of this string is less than
128 octets, any 'missing' octets are assumed to contain
the value zero. An NMS may omit any zero-valued octets
from the end of this string in order to reduce SetPDU
size, and the agent may also omit zero-valued trailing
octets, to reduce the size of GetResponse PDUs.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.2.1.4 |
cpvlanPromPortSecondaryRemap4kA string of octets containing one bit per VLAN for
VLANs with VlanIndexOrZero values of 3072 through 4095
in the management domain on this port. The first octet
corresponds to VLANs with VlanIndexOrZero values of 3072
through 3079; the second octet to VLANs 3080 through
3087; etc. The most significant bit of each octet
corresponds to the lowest value VlanIndexOrZero in
that octet.
A bit can only be set to '1' when the bit is
corresponding to a VLAN of Private VLAN isolated or
community type which has already been associated with a
primary VLAN. Setting this bit to '1' makes this
promiscuous port remap the secondary VLAN to its
associated primary VLAN for egress traffic on the fly,
or remap the associated primary VLAN to the secondary
VLAN if the secondary VLAN is of twoWayCommunity type
and the object value of cpvlanPromPortTwoWayRemapCapable
for this promiscuous port is true(1).
Note that if the length of this string is less than
128 octets, any 'missing' octets are assumed to contain
the value zero. An NMS may omit any zero-valued octets
from the end of this string in order to reduce SetPDU
size, and the agent may also omit zero-valued trailing
octets, to reduce the size of GetResponse PDUs.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.2.1.5 |
cpvlanPromPortTwoWayRemapCapableIndicates whether the port is capable to perform
remapping from primary VLANs to the twoWayCommunity VLANs
associated with them for the Private VLAN feature. A
promiscuous port with this object value of false(2) can
only perform one-way remapping from secondary VLANs to
their associated primary VLANs, while a promiscuous port
with this object value of true(1) can also perform
remapping from primary VLANs to the twoWayCommunity VLANs
associated with them in addition to that.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.173.1.2.2.1.6 |
cpvlanPortModeTableA table containing information of the configuration of
port mode for the Private VLAN feature. SEQUENCE OF CpvlanPortModeEntry .1.3.6.1.4.1.9.9.173.1.2.3 |
cpvlanPortModeEntryA conceptual row containing information of the
configuration of port mode on each port for the
Private VLAN feature. An entry of this table is
created by the managed system when the capability
to be a Private VLAN port is detected on an
interface. CpvlanPortModeEntry .1.3.6.1.4.1.9.9.173.1.2.3.1 |
cpvlanPortModeThe Private VLAN port mode on this port.
nonPrivateVlan(1)
non-Private-VLAN port.
host(2)
a Private-VLAN host port, i.e., private
port.
promiscuous(3)
a Private-VLAN promiscuous port.
trunk(4)
Private-VLAN trunk port.rw Enumeration .1.3.6.1.4.1.9.9.173.1.2.3.1.1 |
cpvlanTrunkPortTableA table containing information of the configuration of
a private vlan trunk port in the device. This includes
secondary and normal allowed VLAN, encapsulation type,
trunk native vlan (as applied to private vlan trunks). SEQUENCE OF CpvlanTrunkPortEntry .1.3.6.1.4.1.9.9.173.1.2.4 |
cpvlanTrunkPortEntryA conceptual row containing information of the
configuration of one private vlan trunk port. An entry
is created by the managed system for each interface which
can be configured as a private vlan trunk port CpvlanTrunkPortEntry .1.3.6.1.4.1.9.9.173.1.2.4.1 |
cpvlanTrunkPortDynamicStateFor private VLAN trunk ports, this object allows the
operator to mandate the trunking behavior of the port
on(1) dictates that the private VLAN port will always be a
trunk. If the negotiation is supported on this port,
negotiation will take place with the far end to attempt to
bring the far end into trunking state.
onNoNegotiate(2) is used to indicate that the interface is
permanently set to be a trunk, and no negotiation takes
place with the far end on the link to ensure consistent
operation. This is similar to on(1) except no negotiation
takes place with the far end.
If a port does not support negotiation, the value of on(1)
is not allowed. If the port's cpvlanTrunkPortEncapType is
set to negotiate(3), onNoNegotiate(2) is not allowed.rw Enumeration .1.3.6.1.4.1.9.9.173.1.2.4.1.1 |
cpvlanTrunkPortEncapTypeThe type of VLAN encapsulation desired to be used on this
private vlan trunk port.
It is either a particular type, or 'negotiate' meaning
whatever type results from the negotiation.
dot1Q(1) indicates that the port should accept and transmit
packets with IEEE 802.1q VLAN encapsulation
isl(2) indicates that the port should accept and transmit
packets with Inter Switch Link (ISL) VLAN encapsulation
negotiate(3) indicates that the VLAN encapsulation is
negotiated with the far end. The negotiated VLAN
encapsulation can be dot1Q or isl. negotiate(2) is not
allowed if the port does not support negotiation of
VLAN encapsulation type or if its
cpvlanTrunkPortDynamicState is set to onNoNegotiate(2)rw Enumeration .1.3.6.1.4.1.9.9.173.1.2.4.1.2 |
cpvlanTrunkPortNativeVlanThe VlanIndex of the VLAN which is represented by native
frames on this private vlan trunk port. For private vlan
trunk ports that need to drop untagged frames or not
supporting the sending and receiving of native frames,
this value should be set to zerorw VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.2.4.1.3 |
cpvlanTrunkPortSecondaryVlansA string of octets containing one bit per VLAN for VLANs
with values of 0 through 1023 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a secondary VLAN that has already been
associated with a primary VLAN, it allows this private
VLAN trunk port to remap the secondary VLAN to its primary
VLAN for ingress traffic and to remap its associated primary
VLAN to the secondary VLAN for egress traffic.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a secondary VLAN, then the local
system is enabled to transmit and receive frames with
proper VLAN remapping via this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a normal VLAN,
then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.4 |
cpvlanTrunkPortSecondaryVlans2kA string of octets containing one bit per VLAN for VLANs
with values of 1024 through 2047 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a secondary VLAN that has already been
associated with a primary VLAN, it allows this private
VLAN trunk port to remap the secondary VLAN to its primary
VLAN for ingress traffic and to remap its associated primary
VLAN to the secondary VLAN for egress traffic.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a secondary VLAN, then the local
system is enabled to transmit and receive frames with
proper VLAN remapping via this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a normal VLAN,
then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of VLANs up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.5 |
cpvlanTrunkPortSecondaryVlans3kA string of octets containing one bit per VLAN for VLANs
with values of 2048 through 3071 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a secondary VLAN that has already been
associated with a primary VLAN, it allows this private
VLAN trunk port to remap the secondary VLAN to its primary
VLAN for ingress traffic and to remap its associated primary
VLAN to the secondary VLAN for egress traffic.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a secondary VLAN, then the local
system is enabled to transmit and receive frames with
proper VLAN remapping via this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a normal VLAN,
then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.6 |
cpvlanTrunkPortSecondaryVlans4kA string of octets containing one bit per VLAN for VLANs
with values of 3072 through 4095 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a secondary VLAN that has already been
associated with a primary VLAN, it allows this private
VLAN trunk port to remap the secondary VLAN to its primary
VLAN for ingress traffic and to remap its associated primary
VLAN to the secondary VLAN for egress traffic.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a secondary VLAN, then the local
system is enabled to transmit and receive frames with
proper VLAN remapping via this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a normal VLAN,
then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.7 |
cpvlanTrunkPortNormalVlansA string of octets containing one bit per VLAN for VLANs
with values of 0 through 1023 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a normal VLAN, it allows packets belonging to
this vlan on this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a normal VLAN, then the local
system is enabled to transmit and receive frames as
normal VLAN
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a secondary
VLAN, then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.8 |
cpvlanTrunkPortNormalVlans2kA string of octets containing one bit per VLAN for VLANs
with values of 1024 through 2047 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a normal VLAN, it allows packets belonging to
this vlan on this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a normal VLAN, then the local
system is enabled to transmit and receive frames as
normal VLAN
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a secondary
VLAN, then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.9 |
cpvlanTrunkPortNormalVlans3kA string of octets containing one bit per VLAN for VLANs
with values of 2048 through 3071 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a normal VLAN, it allows packets belonging to
this vlan on this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a normal VLAN, then the local
system is enabled to transmit and receive frames as
normal VLAN
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a secondary
VLAN, then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.10 |
cpvlanTrunkPortNormalVlans4kA string of octets containing one bit per VLAN for VLANs
with values of 3072 through 4095 in the management domain
on this port.
If the VLAN represented by setting a bit to '1' in the
bitmap is a normal VLAN, it allows packets belonging to
this vlan on this Private VLAN trunk port.
If the bit corresponding to a VLAN is set to '1' and if
the corresponding VLAN is a normal VLAN, then the local
system is enabled to transmit and receive frames as
normal VLAN
If the bit corresponding to a VLAN is set to '0', and if
the corresponding VLAN is not configured as a secondary
VLAN, then the system is disabled from sending and receiving
frames on that VLAN via this Private VLAN trunk port.
This object is only instantiated on devices which support
the range of VlanIndexOrZero up to 4095.rw VlanIndexBitmap -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.173.1.2.4.1.11 |
cpvlanTrunkPortDynamicStatusIndicates the current dynamic trunking status of the
specified private VLAN port.
trunking(1) indicates that the private VLAN port is
currently operating as a private VLAN trunk port
notTrunking(2) indicates that the private VLAN port
is currently not trunking but is operating as an
access port.ro Enumeration .1.3.6.1.4.1.9.9.173.1.2.4.1.12 |
cpvlanTrunkPortEncapOperTypeThe type of VLAN encapsulation in use on this private
vlan trunk port.
dot1Q(1) indicates that the port accepts and transmits
packets with IEEE 802.1q VLAN encapsulation
isl(2) indicates that the port accepts and transmits
packets with Inter Switch Link (ISL) VLAN encapsulation
If the cpvlanTrunkPortDynamicStatus is notTrunking(2) or
if the encapsulation type negotiation has not been
completed, the object is set to notApplicable(3).ro Enumeration .1.3.6.1.4.1.9.9.173.1.2.4.1.13 |
cpvlanSVIObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.1.3 |
cpvlanSVIMappingTableA table containing the configuration of
primary VLAN SVI (Switch Virtual Interfaces)
mapping for the secondary VLANs for the Private
VLAN feature. SEQUENCE OF CpvlanSVIMappingEntry .1.3.6.1.4.1.9.9.173.1.3.1 |
cpvlanSVIMappingEntryA conceptual row containing the Primary VLAN
SVI mapping configuration for the existing
secondary VLANs. An entry is created by the managed
system for each VLAN with corresponding VLAN's
cpvlanVlanPrivateVlanType of isolated(3),
community(4), and twoWayCommunity(5). CpvlanSVIMappingEntry .1.3.6.1.4.1.9.9.173.1.3.1.1 |
cpvlanSVIMappingVlanIndexAn index value that uniquely identifies the
Virtual LAN associated with this information. VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.3.1.1.1 |
cpvlanSVIMappingPrimarySVIThe Vlan ID of the primary VLAN SVI this secondary
VLAN is mapped to for the Private VLAN feature.
This object has the value of zero if this secondary
VLAN is not mapped to any primary VLAN SVI.rw VlanIndexOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.173.1.3.1.1.2 |
cpvlanMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2 |
cpvlanMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.1 |
cpvlanMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.1.1 |
cpvlanMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2 |
cpvlanVlanGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.1 |
cpvlanPrivatePortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.2 |
cpvlanPromPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.3 |
cpvlanPromPort4kGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.4 |
cpvlanPortModeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.5 |
cpvlanSVIMappingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.6 |
cpvlanTrunkPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.173.2.2.7 |