Home/Catalog/CISCO-OPTICAL-MIB

CISCO-OPTICAL-MIB

AI MIB Summary

The CISCO-OPTICAL-MIB enables monitoring of Cisco optical interface physical layer characteristics and protocol-specific performance counters, specifically tracking metrics such as Laser Bias Current (LBC), Optical Signal to Noise Ratio (OSNR), Chromatic Dispersion (CD), and Polarization Mode Dispersion (PMD). It facilitates the configuration of threshold crossing alarms (TCAs) to detect performance degradation by comparing real-time parameter values against defined error levels during accumulation cycles.

This MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer.
Main OID:
ciscoOpticalMIB.1.3.6.1.4.1.9.9.828
167
Objects
Active
Status
5
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
SNMPv2-CONF
IF-MIB
CISCO-SMI

Objects

167 total
Object Name
ciscoOpticalMIBThis MIB module defines the managed objects for physical layer characteristics of optical interfaces and performance statistics objects for protocol specific counters in optical devices. Performance monitoring (PM) parameters are used by service providers to gather, store, set thresholds for and report performance data for early detection of problems. Thresholds are used to set error levels for each PM parameter. During the accumulation cycle, if the current value of a performance monitoring parameter reaches or exceeds its corresponding threshold value, a threshold crossing alarm (TCA) is generated. The TCAs provide early detection of performance degradation. Glossary: LBC : Laser Bias Current TX : Transmit RX : Receive PMD : Polarization Mode Dispersion OSNR : Optical Signal to Noise Ratio DGD : Differential Group Delay CD : Chromatic Dispersion rad/s : radian per second dB : decibel dBm : decibel-milliwatt ps : picosecond nm : nanometer.
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.828
ciscoOpticalMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.0
coiOpticsStatusChangeThis notification is generated whenever the defect status of Optics on an interface changes. Varbind 'ifIndex' indicates the interface whose defect status of the Optics layer has just changed. Varbind 'ifName' indicates the interface Name whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerPortType' indicates the port type of the interface whose defect status of the Optics layer has just changed. Varbind 'coiOpticalControllerStatus' indicates the current defect status of the Optics layer on the interface.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.828.0.1
coiOpticalEquipmentAlarmThis notification is generated whenever the optical equipment alarm is generated. Varbind 'coiOpticalAlarmLocation' indicates the location on which equipment failed alarm has generated. Varbind 'coiOpticalAlarmType' indicates the type of alarm. Varbind 'coiOpticalAlarmTimeStamp' indicates the timestamp when alarm is generated. Varbind 'coiOpticalAlarmName' indicates the alarm object. Varbind 'coiOpticalAlarmAdditionalInfo' indicates additional info related to the alarm. Varbind 'coiOpticalAlarmSeverity' indicates the severity of the alarm. Varbind 'coiOpticalAlarmStatus' indicates status of the alarm. Varbind 'coiOpticalAlarmServiceAffecting' indicates the service affected state when alarm is generated.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.828.0.2
ciscoOpticalMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.1
coiOpticalController
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.1.1
coiOpticalNotifEnabledThis object controls the generation of coiOpticsStatusChange notification. If the value of this object is 'true', then the generation of coiOpticsStatusChange notification is enabled. If the value of this object is 'false', then the generation of coiOpticsStatusChange notification is disabled.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.1.1
coiOpticalControllerTableThis table provides management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195).
SEQUENCE OF CoiOpticalControllerEntry
.1.3.6.1.4.1.9.9.828.1.1.2
coiOpticalControllerEntryAn entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
CoiOpticalControllerEntry
.1.3.6.1.4.1.9.9.828.1.1.2.1
coiOpticalControllerWavelengthThis object is used to configure the wavelength on optical channel interfaces in 1/100 nm.rw
CoiOpticalWavelength UNITS "1/100 nm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.1
coiOpticalControllerLaserStatusThis object gives the current operational state of the Laser. Valid values are - 'up' - The laser is operational. 'down' - The laser is not operational.ro
Enumeration
.1.3.6.1.4.1.9.9.828.1.1.2.1.2
coiOpticalControllerFrequencyThis object is used to configure the frequency on optical channel interfaces in 100 MHz.rw
Unsigned32 UNITS "100 MHz"
.1.3.6.1.4.1.9.9.828.1.1.2.1.3
coiOpticalControllerChannelNumberThis object is used to configure the channel number on optical channel interfaces. Channel Number is set to 0 if not 50GHz grid.rw
Unsigned32
.1.3.6.1.4.1.9.9.828.1.1.2.1.4
coiOpticalControllerTransmitPowerThis object is used to configure the Transmit Power in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.5
coiOpticalControllerOpticsTypeThis object gives the description of optics present on optical channel interfaces.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.1.2.1.6
coiOpticalControllerRXLowThresholdThis object is used to configure the Receive Low Threshold in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.7
coiOpticalControllerTXLowThresholdThis object is used to configure the Transmit Low Threshold in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.8
coiOpticalControllerRXHighThresholdThis object is used to configure the Receive High Threshold in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.9
coiOpticalControllerTXHighThresholdThis object is used to configure the Transmit High Threshold in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.10
coiOpticalControllerLBCHighThresholdThis object is used to configure the Laser Bias Current High Threshold in 1/10% on optical channel interfaces.rw
Integer32
.1.3.6.1.4.1.9.9.828.1.1.2.1.11
coiOpticalControllerStatusThis object indicates the current defect status of the Optics layer. noDefect(0): No Defect. This bit is set high when no defect is detected on the optics. improprmvl(1): Improper Removal. This will be set when a physical pluggable is absent on a service (hw-module) provisioned port. mea(2): This bit will be set when Port Pluggable Module Mismatches With Pre-Provisoned PPM. provMismatch(3): Provision Mismatch. This bit is set when Provisioned wavelength is Not supported By Pluggable. highRXPwr(4): High Receive Power. This bit is set when the measured optical power of the received signal exceeds the threshold high value, which is user-provisionable. highTXPwr(5): High Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls over the threshold. lowRXPwr(6): Low Receive Power. This bit is set when the measured optical power of the received signal falls below the low threshold value, which is user-provisionable. lowTXPwr(7): Low Transmit Power. This bit is set when Pluggable measured optical power of the transmitted signal falls below the low threshold. highLBC(8): High Laser Bias. This bit is set when the Physical Pluggable Port laser reads laser bias value beyond configured high threshold. highDGD(9): High DGD. This bit is set when the pluggable port Module reads the Differential Group delay value that exceeds the configured high threshold. outOfRangeCD(10): Out of Range Chromatic Dispersion. This bit is set when the Chromatic dispersion value read by the associated HW is out of range with the configured threshold. lowOSNR(11): Low Optical Signal to Noise Ratio. This bit is set when the HW read Optical Signal to Noise ratio falls below the configured low threshold. wvlOutOfLock(12): Wavelength Out of Lock. This bit is set when Trunk Port optics detects that optical input frequency is out of range. highLaserTemp(13): High LaserTemp.This bit is set when the internally measured transceiver temperature exceeds the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. lowLaserTemp(14): Low LaserTemp. This bit is set when the internally measured transceiver temperature falls below the card setting by 35.6 degrees F or 2 degrees C. A laser temperature change affects the transmitted wavelength. (This temperature is equivalent to about 200 picometers of wavelength. ppmFail(15): Pluggable Equipment Fail. This bit is set when Pluggable Equipment is not operational or manageable. This object is sent out as a notification to the agent.ro
Bits
.1.3.6.1.4.1.9.9.828.1.1.2.1.12
coiOpticalControllerPortTypeThis object gives the port type of the optical interface.ro
CoiPortType
.1.3.6.1.4.1.9.9.828.1.1.2.1.13
coiOpticalControllerTotalRXPowerThis object is used to configure the total receive power in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.14
coiOpticalControllerTotalTXPowerThis object is used to configure the total transmit power in 1/100 dBm on optical channel interfaces.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.2.1.15
coiOpticalControllerPerLaneTableThis table provides the management information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and lane number as coiOpticalControllerLane.
SEQUENCE OF CoiOpticalControllerPerLaneEntry
.1.3.6.1.4.1.9.9.828.1.1.3
coiOpticalControllerPerLaneEntryAn entry containing management information on optical layer related attributes of interfaces with an ifType opticalChannel(195) and lane number as coiOpticalControllerLane. Entries are created by the feature when a new interface is added to the ifTable.
CoiOpticalControllerPerLaneEntry
.1.3.6.1.4.1.9.9.828.1.1.3.1
coiOpticalControllerLaneThis object specifies the lane number for the optical controller. Each optical controller is divided into data lanes, with each lane operating at some data rate, giving an aggregated bandwidth of the controller, as a whole. Lane is applicable for breakout mode of operation.
Integer32
.1.3.6.1.4.1.9.9.828.1.1.3.1.1
coiOpticalControllerPerLaneRXPowerThis object specifies the Receive power in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.3.1.2
coiOpticalControllerPerLaneTXPowerThis object specifies the Transmit power in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.1.3.1.3
coiOpticalControllerPerLaneLBCThis object specifies the Laser Bias Current in 1/10%.ro
Integer32
.1.3.6.1.4.1.9.9.828.1.1.3.1.4
coiOpticalControllerPerLaneOSNRThis object specifies the Optical Signal to Noise Ratio in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.1.3.1.5
coiOpticalControllerPerLaneChromaticDispersionThis object specifies the measure of spread of light pulse in ps/nm.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.1.3.1.6
coiOpticalControllerPerLaneDifferentialGroupDelayThis object specifies the propagation time difference between eigenmodes X and Y in 1/100 ps.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.1.3.1.7
coiOpticalControllerPerLaneSecondOrderPMDThis object specifies the threshold Second Order Polarization Mode Dispersion in 1/100 ps^2.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.1.3.1.8
coiOpticalControllerPerLanePolarizationDependentLossThis object specifies the threshold Polarization Dependent Loss in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.1.3.1.9
coiOpticalControllerPerLanePolarizationChangeRateThis object specifies the Polarization Change Rate in 1/100 rad/s.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.1.3.1.10
coiOpticalControllerPerLanePhaseNoiseThis object specifies the Fluctuations in the Phase of a Waveform in 1/1000 dB.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.1.3.1.11
coiOpticalPerformanceMonitoring
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.1.2
coiOpticalThresholdTableThis table provides threshold information for optical layer related attributes of interfaces with an ifType of opticalChannel(195) and Interval type as coiOptThreshIntervalType.
SEQUENCE OF CoiOpticalThresholdEntry
.1.3.6.1.4.1.9.9.828.1.2.1
coiOpticalThresholdEntryAn entry containing threshold information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
CoiOpticalThresholdEntry
.1.3.6.1.4.1.9.9.828.1.2.1.1
coiOptThreshIntervalTypeThis object gives the interval type during which the performance statistics are accumulated for the interface.
CoiIntervalType
.1.3.6.1.4.1.9.9.828.1.2.1.1.1
coiOptThreshTXPowerMinThis object is used to configure the threshold of minimum Transmit power for the interface in 1/100 dBm.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.2
coiOptThreshRXPowerMinThis object is used to configure the threshold of minimum Receive power for the interface in 1/100 dBm.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.3
coiOptThreshOSNRMinThis object is used to configure the threshold of minimum Optical Signal to Noise Ratio for the interface in 1/100 dB.rw
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.4
coiOptThreshChromaticDispersionMinThis object is used to configure the threshold of minimum measure of spread of light pulse for the interface in ps/nm.rw
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.5
coiOptThreshDifferentialGroupDelayMinThis object is used to configure the threshold of minimum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.rw
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.1.1.6
coiOptThreshSecondOrderPMDMinThis object is used to configure the threshold of minimum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.rw
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.1.1.7
coiOptThreshPolarizationDependentLossMinThis object is used to configure the threshold of minimum Polarization Dependent Loss for the interface in 1/100 dB.rw
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.8
coiOptThreshPolarizationChangeRateMinThis object is used to configure the threshold of minimum Polarization Change Rate for the interface in 1/100 rad/s.rw
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.1.1.9
coiOptThreshPhaseNoiseMinThis object is used to configure the threshold of minimum Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.rw
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.10
coiOptThreshLBCMinThis object is used to configure the threshold of minumum Laser Bias Current in 1/10%.rw
Integer32
.1.3.6.1.4.1.9.9.828.1.2.1.1.11
coiOptThreshTXPowerMaxThis object is used to configure the threshold of maximum Transmit power for the interface in 1/100 dBm.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.12
coiOptThreshRXPowerMaxThis object is used to configure the threshold of maximum Receive power for the interface in 1/100 dBm.rw
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.13
coiOptThreshOSNRMaxThis object is used to configure the threshold of maximum Optical Signal to Noise Ratio for the interface in 1/100 dB.rw
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.14
coiOptThreshChromaticDispersionMaxThis object is used to configure the threshold of maximum measure of spread of light pulse for the interface in ps/nm.rw
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.1.1.15
coiOptThreshDifferentialGroupDelayMaxThis object is used to configure the threshold of maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.rw
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.1.1.16
coiOptThreshSecondOrderPMDMaxThis object is used to configure the threshold of maximum Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.rw
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.1.1.17
coiOptThreshPolarizationDependentLossMaxThis object is used to configure the threshold of maximum Polarization Dependent Loss for the interface in 1/100 dB.rw
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.18
coiOptThreshPolarizationChangeRateMaxThis object is used to configure the threshold of maximum Polarization Change Rate in 1/100 rad/s for the interface.rw
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.1.1.19
coiOptThreshPhaseNoiseMaxThis object is used to configure the threshold of maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.rw
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.1.1.20
coiOptThreshLBCMaxThis object is used to configure the threshold of maximum Laser Bias Current in 1/10 % for the interface.rw
Integer32
.1.3.6.1.4.1.9.9.828.1.2.1.1.21
coiOptThreshTXPowerEnableMinThis object is used to configure the enablement of threshold min Transmit power for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.22
coiOptThreshRXPowerEnableMinThis object is used to configure the enablement of the threshold min Receive power for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.23
coiOptThreshOSNREnableMinThis object is used to configure the enablement of the threshold min Optical Signal to Noise Ratio for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.24
coiOptThreshChromaticDispersionEnableMinThis object is used to configure the enablement of the threshold min measure of spread of light pulse for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.25
coiOptThreshDifferentialGroupDelayEnableMinThis object is used to configure the enablement of the threshold min propagation time difference between eigenmodes X and Y for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.26
coiOptThreshSecondOrderPMDEnableMinThis object is used to configure the enablement of the threshold min Second Order Polarization Mode Dispersion for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.27
coiOptThreshPolarizationDependentLossEnableMinThis object is used to configure the enablement of the threshold min Polarization Dependent Loss for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.28
coiOptThreshPolarizationChangeRateEnableMinThis object is used to configure the enablement of the threshold min Polarization Change Rate for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.29
coiOptThreshPhaseNoiseEnableMinThis object is used to configure the enablement of the threshold min Fluctuations in the Phase of a Waveform for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.30
coiOptThreshLBCEnableMinThis object is used to configure the enablement of the threshold min Laser Bias Current for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.31
coiOptThreshTXPowerEnableMaxThis object is used to configure the enablement of the threshold max Transmit power for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.32
coiOptThreshRXPowerEnableMaxThis object is used to configure the enablement of the threshold max Receive power for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.33
coiOptThreshOSNREnableMaxThis object is used to configure the enablement of the threshold max Optical Signal to Noise Ratio for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.34
coiOptThreshChromaticDispersionEnableMaxThis object is used to configure the enablement of the threshold max measure of spread of light pulse for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.35
coiOptThreshDifferentialGroupDelayEnableMaxThis object is used to configure the enablement of the threshold max propagation time difference between eigenmodes X and Y for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.36
coiOptThreshSecondOrderPMDEnableMaxThis object is used to configure the enablement of the threshold max Second Order Polarization Mode Dispersion for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.37
coiOptThreshPolarizationDependentLossEnableMaxThis object is used to configure the enablement of the threshold max Polarization Dependent Loss for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.38
coiOptThreshPolarizationChangeRateEnableMaxThis object is used to configure the enablement of the threshold max Polarization Change Rate for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.39
coiOptThreshPhaseNoiseEnableMaxThis object is used to configure the enablement of the threshold max Fluctuations in the Phase of a Waveform for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.40
coiOptThreshLBCEnableMaxThis object is used to configure the enablement of the threshold max Laser Bias Current for the interface.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.2.1.1.41
coiOpticalCurrentTableThis table provides current information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), Lane as coiOptCurrentLane and Interval as coiOptCurrentIntervalType.
SEQUENCE OF CoiOpticalCurrentEntry
.1.3.6.1.4.1.9.9.828.1.2.2
coiOpticalCurrentEntryAn entry containing current information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
CoiOpticalCurrentEntry
.1.3.6.1.4.1.9.9.828.1.2.2.1
coiOptCurrentLaneThis object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole. Lane is applicable for breakout mode of operation.
Integer32
.1.3.6.1.4.1.9.9.828.1.2.2.1.1
coiOptCurrentIntervalTypeThis object gives the interval type during which the current performance statistics are accumulated.
CoiIntervalType
.1.3.6.1.4.1.9.9.828.1.2.2.1.2
coiOptCurrentTXPowerMaxThis object specifies the current max Transmit power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.3
coiOptCurrentRXPowerMaxThis object specifies the current max Receive power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.4
coiOptCurrentOSNRMaxThis object specifies the current max Optical Signal to Noise Ratio for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.5
coiOptCurrentChromaticDispersionMaxThis object specifies the current max measure of spread of light pulse for the interface in ps/nm.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.6
coiOptCurrentDifferentialGroupDelayMaxThis object specifies the current max propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.2.1.7
coiOptCurrentSecondOrderPMDMaxThis object specifies the current max Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.2.1.8
coiOptCurrentPolarizationDependentLossMaxThis object specifies the current max Polarization Dependent Loss for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.9
coiOptCurrentPolarizationChangeRateMaxThis object specifies the current max Polarization Change Rate for the interface in 1/100 rad/s.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.2.1.10
coiOptCurrentPhaseNoiseMaxThis object specifies the current max Fluctuations in the Phase of a Waveform for the interface in 1/1000 dB.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.11
coiOptCurrentLBCMaxThis object specifies the current max Laser Bias Current in 1/10% for the interface.ro
Integer32
.1.3.6.1.4.1.9.9.828.1.2.2.1.12
coiOptCurrentTXPowerMinThis object specifies the current min Transmit power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.13
coiOptCurrentRXPowerMinThis object specifies the current min Receive power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.14
coiOptCurrentOSNRMinThis object specifies the current min Optical Signal to Noise Ratio for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.15
coiOptCurrentChromaticDispersionMinThis object specifies the current min measure of spread of light pulse for the interface in ps/nm.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.16
coiOptCurrentDifferentialGroupDelayMinThis object specifies the current min propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.2.1.17
coiOptCurrentSecondOrderPMDMinThis object specifies the current min Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.2.1.18
coiOptCurrentPolarizationDependentLossMinThis object specifies the current min Polarization Dependent Loss for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.19
coiOptCurrentPolarizationChangeRateMinThis object specifies the current min Polarization Change Rate for the interface in 1/100 rad/s.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.2.1.20
coiOptCurrentPhaseNoiseMinThis object specifies the current min Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.21
coiOptCurrentLBCMinThis object specifies the current min Laser Bias Current in 1/10% for the interface.ro
Integer32
.1.3.6.1.4.1.9.9.828.1.2.2.1.22
coiOptCurrentTXPowerAvgThis object specifies the current average Transmit power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.23
coiOptCurrentRXPowerAvgThis object specifies the current average Receive power for the interface in 1/100 dBm.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.24
coiOptCurrentOSNRAvgThis object specifies the current average Optical Signal to Noise Ratio for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.25
coiOptCurrentChromaticDispersionAvgThis object specifies the current average measure of spread of light pulse for the interface in ps/nm.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.2.1.26
coiOptCurrentDifferentialGroupDelayAvgThis object specifies the current average propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.2.1.27
coiOptCurrentSecondOrderPMDAvgThis object specifies the current average Second Order Polarization Mode Dispersion for the interface in 1/100 ps^2.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.2.1.28
coiOptCurrentPolarizationDependentLossAvgThis object specifies the current average Polarization Dependent Loss for the interface in 1/100 dB.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.29
coiOptCurrentPolarizationChangeRateAvgThis object specifies the current average Polarization Change Rate for the interface in 1/100 rad/s.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.2.1.30
coiOptCurrentPhaseNoiseAvgThis object specifies the current average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.2.1.31
coiOptCurrentLBCAvgThis object specifies the current average Laser Bias Current in 1/10% for the interface.ro
Integer32
.1.3.6.1.4.1.9.9.828.1.2.2.1.32
coiOptCurrentTimestampThis object specifies the timestamp for the current bucket for the interface.ro
OCTET STRING
.1.3.6.1.4.1.9.9.828.1.2.2.1.33
coiOpticalIntervalTableThis table provides interval information for optical layer related attributes of interfaces with an ifType of opticalChannel(195), lane as coiOptIntervalLane, Interval as coiOptIntervalIntervalType and history bucket as coiOptIntervalIntervalType.
SEQUENCE OF CoiOpticalIntervalEntry
.1.3.6.1.4.1.9.9.828.1.2.3
coiOpticalIntervalEntryAn entry containing interval information on optical layer related attributes of interfaces with an ifType opticalChannel(195). Entries are created by the feature when a new interface is added to the ifTable.
CoiOpticalIntervalEntry
.1.3.6.1.4.1.9.9.828.1.2.3.1
coiOptIntervalLaneThis object specifies the lane number for the optical interface. Each optical controller is divided into data lanes with each lane operating at some data rate, giving an aggregated bandwidth of the controller as a whole.Lane is applicable for breakout mode of operation.
Integer32
.1.3.6.1.4.1.9.9.828.1.2.3.1.1
coiOptIntervalIntervalTypeThis object gives the interval type during which the performance statistics are accumulated.
CoiIntervalType
.1.3.6.1.4.1.9.9.828.1.2.3.1.2
coiOptIntervalNumThis object identifies the interval for which the set of interval performance values is available. The interval identified by 1 is the most recent 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1.
Integer32
.1.3.6.1.4.1.9.9.828.1.2.3.1.3
coiOptIntervalTXPowerMaxThis object specifies the interval maximum Transmit power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.4
coiOptIntervalRXPowerMaxThis object specifies the interval maximum Receive power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.5
coiOptIntervalOSNRMaxThis object specifies the interval maximum Optical Signal to Noise Ratio in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.6
coiOptIntervalChromaticDispersionMaxThis object specifies the interval maximum measure of spread of light pulse for the interface in ps/nm.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.7
coiOptIntervalDifferentialGroupDelayMaxThis object specifies the interval maximum propagation time difference between eigenmodes X and Y for the interface in 1/100 ps.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.3.1.8
coiOptIntervalSecondOrderPMDMaxThis object specifies the interval maximum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.3.1.9
coiOptIntervalPolarizationDependentLossMaxThis object specifies the interval maximum Polarization Dependent Loss in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.10
coiOptIntervalPolarizationChangeRateMaxThis object specifies the interval maximum Polarization Change Rate in 1/100 rad/s for the interface.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.3.1.11
coiOptIntervalPhaseNoiseMaxThis object specifies the interval maximum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.12
coiOptIntervalLBCMaxThis object specifies the interval maximum Laser Bias Current in 1/10% for the interface.ro
Integer32 UNITS "1/10 %"
.1.3.6.1.4.1.9.9.828.1.2.3.1.13
coiOptIntervalTXPowerMinThis object specifies the interval minimum Transmit power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.14
coiOptIntervalRXPowerMinThis object specifies the interval minimum Receive power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.15
coiOptIntervalOSNRMinThis object specifies the interval minimum Optical Signal to Noise Ratio in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.16
coiOptIntervalChromaticDispersionMinThis object specifies the interval minimum measure of spread of light pulse in ps/nm for the interface.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.17
coiOptIntervalDifferentialGroupDelayMinThis object specifies the interval minimum propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.3.1.18
coiOptIntervalSecondOrderPMDMinThis object specifies the interval minimum Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.3.1.19
coiOptIntervalPolarizationDependentLossMinThis object specifies the interval minimum Polarization Dependent Loss in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.20
coiOptIntervalPolarizationChangeRateMinThis object specifies the interval minimum Polarization Change Rate in 1/100 rad/s for the interface.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.3.1.21
coiOptIntervalPhaseNoiseMinThis object specifies the interval minimum Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.22
coiOptIntervalLBCMinThis object specifies the interval minimum Laser Bias Current in 1/10% for the interface.ro
Integer32 UNITS "1/10 %"
.1.3.6.1.4.1.9.9.828.1.2.3.1.23
coiOptIntervalTXPowerAvgThis object specifies the interval average Transmit power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.24
coiOptIntervalRXPowerAvgThis object specifies the interval average Receive power in 1/100 dBm for the interface.ro
CoiOpticalPower UNITS "1/100 dBm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.25
coiOptIntervalOSNRAvgThis object specifies the interval average Optical Signal to Noise Ratio in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.26
coiOptIntervalChromaticDispersionAvgThis object specifies the interval average measure of spread of light pulse in ps/nm for the interface.ro
Integer32 UNITS "ps/nm"
.1.3.6.1.4.1.9.9.828.1.2.3.1.27
coiOptIntervalDifferentialGroupDelayAvgThis object specifies the interval average propagation time difference between eigenmodes X and Y in 1/100 ps for the interface.ro
Integer32 UNITS "1/100 ps"
.1.3.6.1.4.1.9.9.828.1.2.3.1.28
coiOptIntervalSecondOrderPMDAvgThis object specifies the interval average Second Order Polarization Mode Dispersion in 1/100 ps^2 for the interface.ro
Integer32 UNITS "1/100 ps^2"
.1.3.6.1.4.1.9.9.828.1.2.3.1.29
coiOptIntervalPolarizationDependentLossAvgThis object specifies the interval average Polarization Dependent Loss in 1/100 dB for the interface.ro
Integer32 UNITS "1/100 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.30
coiOptIntervalPolarizationChangeRateAvgThis object specifies the interval average Polarization Change Rate in 1/100 rad/s for the interface.ro
Integer32 UNITS "1/100 rad/s"
.1.3.6.1.4.1.9.9.828.1.2.3.1.31
coiOptIntervalPhaseNoiseAvgThis object specifies the interval average Fluctuations in the Phase of a Waveform in 1/1000 dB for the interface.ro
Integer32 UNITS "1/1000 dB"
.1.3.6.1.4.1.9.9.828.1.2.3.1.32
coiOptIntervalLBCAvgThis object specifies the interval average Laser Bias Current in 1/10 % for the interface.ro
Integer32 UNITS "1/10 %"
.1.3.6.1.4.1.9.9.828.1.2.3.1.33
coiOptIntervalTimestampThis object specifies the timestamp, for the bucket specified by 'coiOptIntervalNum', for the interface.ro
OCTET STRING
.1.3.6.1.4.1.9.9.828.1.2.3.1.34
coiOpticalClientInfoTableThis table provides management information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6).This parameter is applicable only for client interfaces.
SEQUENCE OF CoiOpticalClientInfoEntry
.1.3.6.1.4.1.9.9.828.1.3
coiOpticalClientInfoEntryAn entry containing information for optical's client layer related attributes of interfaces with an ifType of ethernetCsmacd(6). Entries are created by the feature when the interface discovers the neighbour's ethernet MAC Address.
CoiOpticalClientInfoEntry
.1.3.6.1.4.1.9.9.828.1.3.1
coiOpticalClientEthernetNeighbourMACThis object gives the neighbour MAC Address to which the interface is connected.ro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.3.1.1
coiOpticalEquipmentAlarmGroup
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.1.4
coiOpticalAlarmLocationThis object indicates the location of the component that raised alarm, within the device.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.4.1
coiOpticalAlarmTypeThis object indicates the type of alarm that is raised.ro
CoiOptAlarmType
.1.3.6.1.4.1.9.9.828.1.4.2
coiOpticalAlarmTimeStampThis object gives the time when an event occurred. This is accurate only upto a second.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.4.3
coiOpticalAlarmNameThis variable gives the user-visible name, which uniquely identifies the alarm in the system.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.4.4
coiOpticalAlarmAdditionalInfoThis variable provides additional info about the alarm. This object would be a null string if no additional information is specified.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.9.9.828.1.4.5
coiOpticalAlarmSeverityThis variable specifies alarm severity.ro
CoiOptAlarmSeverity
.1.3.6.1.4.1.9.9.828.1.4.6
coiOpticalAlarmStatusThis variable specifies alarm status.ro
CoiOptAlarmStatus
.1.3.6.1.4.1.9.9.828.1.4.7
coiOpticalAlarmServiceAffectingThis variable specifies the service affecting state of the alarm.ro
CoiOptAlarmServiceAffecting
.1.3.6.1.4.1.9.9.828.1.4.8
ciscoOpticalMIBConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.2
ciscoOpticalMIBCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.2.1
ciscoOpticalMIBGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.828.2.2
CISCO-OPTICAL-MIB - SNMP MIB Reference | MIBs Explorer