CISCO-MEETINGPLACE-MIB
AI MIB Summary
The CISCO-MEETINGPLACE-MIB enables SNMP-based monitoring of Cisco Unified MeetingPlace application servers to track conferencing session usage, resource utilization, and system health status. It facilitates the retrieval of operational metrics via polling and the reception of critical alarm traps for both minor and major system faults.
This MIB allows management of Cisco Unified MeetingPlace (CUMP) features, CUMP is the key conferencing solution component for Cisco Unified Communications. The CUMP MIB runs on the CUMP application server and provides the status/usage information, and minor/major system alarms to the monitoring station. The monitoring station can either pull application server information through the MIB or set as a trap destination to receive alarms.
Main OID:
ciscoMeetingPlaceMIB.1.3.6.1.4.1.9.9.733
42
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
42 total| Object Name |
|---|
ciscoMeetingPlaceMIBThis MIB allows management of Cisco Unified MeetingPlace (CUMP)
features, CUMP is the key conferencing solution component for
Cisco Unified Communications. The CUMP MIB runs on the CUMP
application server and provides the status/usage information,
and minor/major system alarms to the monitoring station. The
monitoring station can either pull application server
information through the MIB or set as a trap
destination to receive alarms. MODULE-IDENTITY .1.3.6.1.4.1.9.9.733 |
ciscoMeetingPlaceMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.0 |
cmpT1DownMeetingPlace T1 line Down Alarm.
This notification indicates that there is a problem with a
telephony port which is caused when the T1 line goes down. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.1 |
cmpGWSimAlarmMeetingPlace Gateway Alarm.
This notification indicates an alarm generated by a MeetingPlace
gateway system, when the gateway system is blocking the
signaling. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.2 |
cmpMajHwAlarmMeetingPlace Major Hardware Alarm. The network management
station will receive the trap, and see the description in
cmpAlarmDesc. The system will keep sending alarms until alarms
have been cleared.
This notification indicates any major hardware alarms reported
in the system.
cmpExCode is MeetingPlace Exception Code
cmpSysUnit is MeetingPlace Server Unit Number
cmpHwDev is MeetingPlace Hardware Device Code
cmpHwUnit is MeetingPlace Hardware Device Unit Number
cmpHwSlot is MeetingPlace Hardware Device Slot Number
cmpHwPort is MeetingPlace Hardware Device Port Number NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.3 |
cmpMinHwAlarmMeetingPlace Minor Hardware Alarm.
This notification indicates any major hardware alarms reported
in the system. The network management station will receive the
trap, and see the description in cmpAlarmDesc. The system will
keep sending alarms until alarms have been cleared.
cmpExCode is MeetingPlace Exception Code
cmpSysUnit is MeetingPlace Server Unit Number
cmpHwDev is MeetingPlace Hardware Device Code
cmpHwUnit is MeetingPlace Hardware Device Unit Number
cmpHwSlot is MeetingPlace Hardware Device Slot Number
cmpHwPort is MeetingPlace Hardware Device Port Number NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.4 |
cmpMajSwAlarmMeetingPlace Major Software Alarm.
This notification indicates any major software alarms reported
in the system. The network management station will receive the
trap, and see the description in cmpAlarmDesc. The system will
keep sending alarms until alarms have been cleared.
cmpExCode is MeetingPlace Exception Code
cmpSysUnit is MeetingPlace Server Unit Number
cmpAlarmDesc is MeetingPlace Alarm Description NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.5 |
cmpMinSwAlarmMeetingPlace Minor Software Alarm.
This notification indicates any minor software alarms reported
in the system. The network management station will receive the
trap, and see the description in cmpAlarmDesc. The system will
keep sending alarms until alarms have been cleared.
cmpExCode is MeetingPlace Exception Code
cmpSysUnit is the MeetingPlace Server Unit Number
cmpAlarmDesc is MeetingPlace Alarm Description NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.733.0.6 |
ciscoMeetingPlaceMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1 |
cmpAlarmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1.1 |
cmpExceptionCodeThis object indicates MeetingPlace Exception Code.
This is the primary code associated with each
MeetingPlace exception condition. Each exception code is
associated with a description, and the monitoring station will
receive the cmpAlarmDesc and the exception code in the same
trap. The application server will keep sending the alarm in
every 1 minute until the event has been cleared.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.1.1 |
cmpSysUnitThis object indicates MeetingPlace Server Unit (Component)
Number.
This is the unit (component) number of the server that
reported the exception. In the MeetingPlace Server, there are
multiple units, such as database, SIP signaling, ..., etc.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.1.2 |
cmpHwDevThis object indicates MeetingPlace Hardware Device Code.
This defines the class of device that generated a
hardware fault.
'mpTemperature' - indicates the hardware temperature is high
'mpPowerSupply' - indicates the power supply failure
'mpSerialPort' - indicates the serial ports failure
'mpTapeDrive' - indicates the tape device failure
'mpHardDrive' - indicates the hard drive failure
'mpDisketteDrive' - indicates the floppy drive failure
'mpEthernet' - indicates the ethernet card failure
'mpModem' - indicates the modem failure
'mpSystemMisc' - indicates the other hardware failure
'mpDSPMSC' - indicates the DSPMSC device failure
'mpDSPPRC' - indicates the DSPPRC device failure
'mpT1Blade' - indicates the T1 line blade device failure
'mpAnalogBlade' - indicates the analog blade device failure
'mpT1Network' - indicates the T1 network device failure
'mpSystemIntegrityCard' - indicates the system integrity card
failure
'mpMainMemory' - indicates the main memory failure
'mpE1Blade' - indicates the E1 blade device failure
'mpE1Network' - indicates the E1 network failure
'mpVoIPBlade' - indicates the Voice Over IP blade failurero Enumeration .1.3.6.1.4.1.9.9.733.1.1.3 |
cmpHwUnitThis object indicates MeetingPlace Hardware Device Unit
Number. This is the unit number of the hardware device that
generated a fault. For a disk this would be the SCSI
ID. For a blade this would the the logical card
number as defined in the system configuration.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.1.4 |
cmpHwSlotThis object indicates MeetingPlace Hardware Device Slot
Number. This is the location of the hardware device that
generated a fault. For a blade this would be the slot
numberro Unsigned32 .1.3.6.1.4.1.9.9.733.1.1.5 |
cmpHwPortThis object indicates MeetingPlace Hardware Device Port
Number. This is the logical port number associated with a
hardware fault. For a T1 alarm, this is the logical
span number.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.1.6 |
cmpAlarmDescThis object indicates MeetingPlace Alarm Description.
This is a one-line text description of the exception
condition. It comprises a string indexed by the
exception code filled in with context-specific values.
The exception code and alarm description has one to one mapping,
the alarm description is in the admin help page.ro SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.733.1.1.7 |
cmpConferenceInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1.2 |
cmpPeakMeetingThis object indicates the maximum number of meetings that
has been scheduled during the last 24 hours time frame.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.2.1 |
cmpPeakHourThis object indicates the peak hour which has the maximum
number of meetings in last 24 hours. For example, if the
meetingplace server has maximum number of meetings at 2pm, it
will give value of 14.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.2.2 |
cmpMeetingCurrentThis object indicates the number of meeting on current moment
at this meetingplace server.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.2.3 |
cmpLicenseInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1.3 |
cmpAudioLicenseThis object indicates the number of audio license is used on
this node.
.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.3.1 |
cmpMaxAudioLicenseThis object indicates the maximum number of audio license that
can be used on this meetingplace system.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.3.2 |
cmpVideoLicenseThis object indicates the number of video license is used on
this node.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.3.3 |
cmpMaxVideoLicenseThis object indicates the maximum number of video license that
can be used on this meetingplace system.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.3.4 |
cmpUsageInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1.4 |
cmpVideoPortsUsageThis object indicates the number of video ports in use at this
meetingplace server on the current moment.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.1 |
cmpMaxVideoPortsAvailableThis object indicates the maximum number of video ports
available on this meetingplace server.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.2 |
cmpAudioPortsUsageThis object indicates the number of audio ports in use at this
meetingplace server on the current moment.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.3 |
cmpMaxAudioPortsAvailableThis object indicates the maximum number of audio ports
available on this meetingplace server.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.4 |
cmpMaxAudioPortsUsage24HoursThis object indicates the maximum number of audio ports has
been used during the last 24 hours.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.5 |
cmpMaxVideoPortsUsage24HoursThis object indicates the maximum number of video ports has
been used during the last 24 hours.ro Unsigned32 .1.3.6.1.4.1.9.9.733.1.4.6 |
cmpNodeInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.1.5 |
cmpNodeDeployTypeThis object indicates the meetingplace deployment type. It can
be webex type I, webex type II and audio only.ro OCTET STRING .1.3.6.1.4.1.9.9.733.1.5.1 |
cmpNodeRoleThis object indicates the role of this MeetingPlace node,
this meetingplace node can be acting as a master node, leaf
node, replica node, or TSPP node.ro OCTET STRING .1.3.6.1.4.1.9.9.733.1.5.2 |
cmpRegionInfoThis object indicates which geographic region the meetingplace
server is located.ro OCTET STRING .1.3.6.1.4.1.9.9.733.1.5.3 |
cmpSiteInfoThis object indicates which geographic site the meetingplace
server is located.ro OCTET STRING .1.3.6.1.4.1.9.9.733.1.5.4 |
cmpNotificationStatusThis object specifies the current status of the notification.
The notifications are generated when the object is set to
'true'. The notifications, which are controlled by this MIB
object, include the cmpT1Down, cmpGWSimAlarm, cmpMajHwAlarm,
cmpMinHwAlarm, cmpMajSwAlarm, and cmpMinSwAlarm.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.733.1.6 |
ciscoMeetingPlaceMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.2 |
cmpMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.2.1 |
cmpMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.733.2.2 |