CISCO-LWAPP-CLOUD-SERVICES-MIB
This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points.
This MIB provides configuration of Network Assurance (NA) ,Connected Mobility Experience (CMX) and Data Externalization(dx) which comes under Cloud services.
Network Assurance (NA) Its a cloud based Assurance which provided by Cisco to monitor the health of the network by collecting data from controllers and Sensors.
Connected Mobility Experience (CMX) The MIB is used for programming Cloud based CMX services. The Network Mobility Service Protocol(NMSP) data is exported to CMX Cloud Server through https connection. The NMSP encoding will remain as it is for the TCP/TLS connection. Use the MIB for configuring URL and Token ID and to enable this serrvice. The Controller will act as https client and will establish https connection with CMX URL. Controller will verify the CMX cloud server while the cloud server will authenticate the Controller using the configured id-token.
Data Externalization(dx) dx is a feature in wlc which allows it to collect the data which may get published to the NA server for analaytics.
The relationship between CC, NA server and the LWAPP APs can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC +.....+ NA +
+ + + + + +
+......+ +......+ +......+
.. . . . .. . . . . . . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +..........+
+ + + + + + + +
+ AP + + AP + + AP +......+ SENSOR +
+ + + + + + + AP +
+......+ +......+ +......+ +..........+
. . . . . . . . . . . . . . . . . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the communication between the Access Points and the Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably.
Sensors
These are wireless clients which periodically connect to a wireless network, run some tests and report back the test status to Cisco Network Assurance Server.
The sensors are controlled and instructed by the Network Assurance server. APs can be tentatively put in Sensor mode to do the Sensor Job. There can be dedicated sensors as well.
Filtered Channels ( FC )
These are user-defined channels which use the filters configured by the user to choose and carry the required data.
Main OID:
ciscoLwappCloudServicesMIB.1.3.6.1.4.1.9.9.838
112
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
112 total| Object Name |
|---|
ciscoLwappCloudServicesMIBThis MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB provides configuration of Network Assurance
(NA) ,Connected Mobility Experience (CMX) and Data
Externalization(dx) which comes under Cloud services.
Network Assurance (NA)
Its a cloud based Assurance which provided by Cisco
to monitor the health of the network by collecting
data from controllers and Sensors.
Connected Mobility Experience (CMX)
The MIB is used for programming Cloud based CMX services.
The Network Mobility Service Protocol(NMSP) data is exported
to CMX Cloud Server through https connection. The NMSP encoding
will remain as it is for the TCP/TLS connection.
Use the MIB for configuring URL and Token ID and to enable
this serrvice. The Controller will act as https client and
will establish https connection with CMX URL.
Controller will verify the CMX cloud server while the cloud
server will authenticate the Controller using the configured
id-token.
Data Externalization(dx)
dx is a feature in wlc which allows it to collect the
data which may get published to the NA server for
analaytics.
The relationship between CC, NA server and the
LWAPP APs can be depicted as follows:
+......+ +......+ +......+
+ + + + + +
+ CC + + CC +.....+ NA +
+ + + + + +
+......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +..........+
+ + + + + + + +
+ AP + + AP + + AP +......+ SENSOR +
+ + + + + + + AP +
+......+ +......+ +......+ +..........+
. . .
. . . .
. . . .
. . . .
. . . .
+......+ +......+ +......+ +......+
+ + + + + + + +
+ MN + + MN + + MN + + MN +
+ + + + + + + +
+......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node
and client are used interchangeably.
Sensors
These are wireless clients which periodically connect
to a wireless network, run some tests and report back
the test status to Cisco Network Assurance Server.
The sensors are controlled and instructed by the
Network Assurance server. APs can be tentatively put
in Sensor mode to do the Sensor Job. There can be
dedicated sensors as well.
Filtered Channels ( FC )
These are user-defined channels which use the filters
configured by the user to choose and carry the required
data. MODULE-IDENTITY .1.3.6.1.4.1.9.9.838 |
clCSMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.0 |
clCSNANotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.0.0 |
clCSNASensorNotReachableDevStatusThis object is used to send a trap whenever the
device status moves out of compliance with
respect to smart-licensing NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.838.0.0.1 |
clCSSecTunNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.0.1 |
clCSSecTunStateChangeThis object is used to send secure
tunnel status change. NOTIFICATION-TYPE .1.3.6.1.4.1.9.9.838.0.1.1 |
clCSMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1 |
clCSNAObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.1 |
clCSNAServerConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.1.1 |
clCSNAServerUrlThis object specifies the URL for network assurance server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.1.1 |
clCSNAServerIdTokenThis object specifies the token id for network assurance
server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.1.2 |
clCSNAServerOnchangeEnableThis object specifies the type of telemetry data that will be
externalized from the controller.
The type can be bulk or onChange.
With onChange enabled, NA server will receive
only the change in data.
With onChange disabled, NA server will receive
the entire dataset(bulk)
A value of 'true' indicates that onchange is enabled.
A value of 'false' indicates that onChange is disabled.
clCSNAServerOnchangeEnable object is superseded by
clCSNAServerChannelOnChangeMode.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.1.3 |
clCSNAServerSyncIntervalThis object specifies the frequency
at which the telemetry data would be received
at the NA server.
fixed - The controller will provide the
telemetry data once in every 5 minutes
adaptive - The controller will provide the
telemetry data once in every 30 seconds
clCSNAServerSyncInterval object is superseded by
clCSNAServerChannelSyncInterval.rwdeprecated Enumeration .1.3.6.1.4.1.9.9.838.1.1.1.4 |
clCSNAServerSubscriptionActionThis object specifies the possible modifications
to the data content in the telemetry stream
sent to the NA server.
add - will add the specified channel
to the telemetry data stream
remove - will remove the specified channel
from the telemetry data stream
clCSNAServerSubscriptionAction object is superseded by
clCSNAServerChannelRowStatus.rwdeprecated Enumeration .1.3.6.1.4.1.9.9.838.1.1.1.5 |
clCSNAServerSubscriptionTopicThis object specifies the channels that can be modified
in the telemetry data stream that is sent to the NA server.
The user can configure a channel from the given enums
system(0) - Configures the system channel
network(1) - Configures the network channel
client(2) - Configures the client channel
ap(3) - Configures the AP channel
rogue(4) - Configures the rogue channel
interferer(5) - Configures the interferer channel
apEvent(6) - Configures the ap-event channel
clientEvent(7) - Configures the client-event channel
scanReport(8) - Configures the scan-report channel
clientDnsReport(9) - Configures the client-dns-report channel
fra(10) - Configures the fra channel
mapserver(11) - Configures the mapserver channel
clCSNAServerSubscriptionTopic object is superseded by
clCSNAServerChannelName
.rwdeprecated Bits .1.3.6.1.4.1.9.9.838.1.1.1.6 |
cLCSNAServerResetSubscriptionsThis object specfies the option to reset NA server channel
subscriptions to defaults.
A value of 'true' indicates that subscriptions are reset.
A value of 'false' indicates that subscriptions are not reset.
User can only set the value 'true'.
Read on this object always returns the value 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.1.7 |
clCSNAGlobalConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.1.2 |
clCSNAEnableThis object specifies whether network assurance is
enabled or disabled.
A value of 'true' indicates that enables network assurance.
A value of 'false' indicates that disables network assurance.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.2.1 |
clCSNASensorBackhaulSSIDThis object specifies the SSID for network assurance
sensor backhaul.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.2.2 |
clCSNASensorBackhaulAuthTypeThis object specifies about authentication type of
network assurance sensor backhaul.
dot1x(1): This value represents the authentication
type as dot1x.
psk(2): This value represents the authentication
type as psk.
open(3): This value represents the authentication
type as open.rw Enumeration .1.3.6.1.4.1.9.9.838.1.1.2.3 |
clCSNASensorBackhaulEapTypeThis object specifies about Extensible Authentication
Protocol (EAP) type of network assurance sensor backhaul.
eapfast(1): This value represents the EAP type as eapfast.
peap(2): This value represents the EAP type as peap.
none(3): This value represents the EAP type as none.rw Enumeration .1.3.6.1.4.1.9.9.838.1.1.2.4 |
clCSNASensorBackhaulUsernameThis object specifies about the username for dot1x type
authentication type of cloud services sensor backhaul.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.2.5 |
clCSNASensorBackhaulPasswordThis object specifies about the password for
dot1x authentication type of network assurance
sensor backhaul.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.2.6 |
clCSNASensorBackhaulPskModeThis object specifies about the psk mode for psk
authentication type of network assurance for sensor
backhaul.
ascii(1): This value represents psk mode as ascii.
hex(2):This value represents psk mode as hex.rw Enumeration .1.3.6.1.4.1.9.9.838.1.1.2.7 |
clCSNASensorBackhaulPskThis object specifies about the psk value for psk
authentication type of network assurance for sensor
backhaul.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.2.8 |
clCSNAASIEnableThis object specifies whether Network Assurance Adaptive
Sync Interval (ASI) mode is enabled or disabled.
A value of 'true' indicates that Network Assurance ASI
mode is enabled.
A value of 'false' indicates that network assurance ASI
mode is disabled.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.2.9 |
clCSNADiffSyncEnableThis object specifies whether Network Assurance diff sync is
enabled or disabled. In diff sync mode only modified parameters
are externalized from the controller.
A value of 'true' indicates that network assurance diff sync
mode is enabled.
A value of 'false' indicates that network assurance diff sync
mode is disabled.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.2.10 |
clCSNATrapMgmtObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.1.3 |
clCSNASensorLradMacAddrThis object represents the AP mac adress
of the sensor.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.3.1 |
clCSNASensorStatusThis object specifies Sensor reachablity to
NA Server.
wsaNoUpdate(1): This value indicated that NA server
status as no update.
wsaStatusOk(2): This value indicated that NA server
status as Reachable.
wsaServerUrlNotReachable(3): This value indicated that
NA server status as Url not reachable.
wsaServerwrongIdToken(4): This value indicated that NA
server status as Wrong Id token configured.
wsaServerProxyNotReachable(5): This value indicated that
NA server status as Proxy server not reachable.
wsaSensorIntf24Error(6): This value indicated that NA
server status as Sensor backhaul error.
wsaSensorIntf24ProxyError(7): This value indicated that
NA server status as Sensor backhaul error.
wsaSensorIntf50Error(8): This value indicated that NA
server status as Sensor backhaul error.
wsaSensorIntf50ProxyError(9): This value indicated that
NA server status as Sensor backhaul error.
wsaApLicenseDenied(10): This value indicated that NA
server status as License denied.
wsaNAServerUnreachable(11): This value indicated that
NA server status as Cloud server not reachable.
wsaAttemptAssocToRoot(12): This value indicated that
NA server status as attempeting the assocation.
wsaAssocToRoot(13): This value indicated that NA server
status as Associated to Root.
wsaTestCfgRcvd(14): This value indicated that NA server
status as Test coverage Recieved.
wsaStatusmax(15): This value indicated that NA server
status as Status maximum.ro Enumeration .1.3.6.1.4.1.9.9.838.1.1.3.2 |
clCSNASensorErrCodeThis object represents Sensor conectivity status.
wsaSensorBackhaulWronSsid(1): This value indicated that
NA server status as Invalid ssid.
wsaSensorBackhaulInvalidCredential(2): This value indicated
that NA server status as Invalid credentials.
wsaSensorConnError(3): This value indicated that NA server
status as Sensor connection error.
wsaNAServerNotFound(4): This value indicated that NA server
status as Server not found-404
wsaNAServerInternalError(5):This value indicated that NA server
status as Sensor connection error.ro Enumeration .1.3.6.1.4.1.9.9.838.1.1.3.3 |
clCSNAServerConfigTable OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.1.4 |
cLCSNAServerChannelTableThis table represents NA server subscription channel
related configurations. SEQUENCE OF CLCSNAServerChannelEntry .1.3.6.1.4.1.9.9.838.1.1.4.1 |
cLCSNAServerChannelEntryEach entry in this table represents and includes the
attributes needed for subscribing a NA server channel CLCSNAServerChannelEntry .1.3.6.1.4.1.9.9.838.1.1.4.1.1 |
clCSNAServerChannelNameThis object specifies the NA server channel name
to subscribe/unsubscribe/set sync interval/set on-change
mode based on the value of respective objects.
'ap': This value indicates aps channel.
'ap-fra': This value indicates ap-fra channel.
'ap-capwap': This value indicates ap-capwap channel.
'ap-channel': This value indicates ap-channel channel.
'ap-fra-sensor': This value indicates ap-fra-sensor channel.
'ap-interface-stats': This value indicates ap-interface-stats
channel.
'ap-inventory': This value indicates ap-inventory channel.
'ap-network-stats': This value indicates ap-network-stats
channel.
'ap-reports': This value indicates ap-reports channel.
'ap-rf': This value indicates ap-rf channel.
'ap-rf-neighbors': This value indicates ap-rf-neighbors channel.
'ap-rf-stats': This value indicates ap-rf-stats channel.
'ap-events': This value indicates ap-events channel.
'ap-system': This value indicates ap-system channel.
'cdp': This value indicates cdp channel.
'client-app-stats': This value indicates client-app-stats
channel.
'client-mobility-stats': This value indicates
client-mobility-stats channel.
'client-network-stats': This value indicates
client-network-stats channel.
'client-policies': This value indicates client-policies channel.
'client-reports': This value indicates client-reports channel.
'client-rf-measurements': This value indicates
client-rf-measurements channel.
'client-traffic-measurements': This value indicates
client-traffic-measurements channel.
'client-wireless-stats': This value indicates
client-wireless-stats channel.
'client-dns-reports': This value indicates
client-dns-reports channel.
'client-events': This value indicates client-events channel.
'client': This value indicates clients channel.
'dhcp': This value indicates dhcp channel.
'eogre': This value indicates eogre channel.
'fabric': This value indicates fabric channel.
'interferers': This value indicates interferers channel.
'licensing': This value indicates licensing channel.
'mobility': This value indicates mobility channel.
'ndp': This value indicates ndp channel.
'radius-events': This value indicates radius-events channel.
'radius': This value indicates radius channel.
'redundancy-events': This value indicates redundancy-events
channel.
'redundancy': This value indicates redundancy channel.
'rogues': This value indicates rogues channel.
'scan-reports': This value indicates scan-reports channel.
'system-core-stats': This value indicates system-core-stats
channel.
'system-dataplane-stats': This value indicates
system-dataplane-stats channel.
'system-general-stats': This value indicates
system-general-stats channel.
'system-port-stats': This value indicates system-port-stats
channel.
'system-process-stats': This value indicates
system-process-stats channel.
'tacacs': This value indicates tacacs channel.
<filter channel name> : User can also specify filter channel
name to subscribe SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.1.4.1.1.1 |
clCSNAServerChannelSyncIntervalThis object specifies the NA server channel sync interval.
fifteen(15): This value indicates 15 sec interval
thirty(30): This value indicates 30 sec interval
sixty(60): This value indicates 60 sec interval
threehundred(300): This value indicates 300 sec interval.
This object can't be used to set interval for
filter-channels.rw Enumeration .1.3.6.1.4.1.9.9.838.1.1.4.1.1.2 |
clCSNAServerChannelOnChangeModeThis object specifies the value of on-change mode of a
NA server channel. Only the changed data is synced if it's
enabled.
A value of 'true' indicates that only changed data
will be synced.
A value of 'false' indicates that all the data
present in DB will be synced.
This object can't be used to set
on-change mode for filter-channels.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.4.1.1.3 |
clCSNAServerIsFilterChannelThis object represents whether the given channel is filter
channel or static channel.
A value of 'true' indicates that the channel is filter channel
A value of 'false' indicates that the channel is
static channelro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.4.1.1.4 |
clCSNAServerChannelRowStatusThis is the status column for this row and is used to
create and delete specific instances of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.1.4.1.1.5 |
clCSDXObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.2 |
clCSDxConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.2.1 |
clCSDxModeThis object specifies whether data externalization is
enabled or disabled.
A value of 'true' indicates that enables DX.
A value of 'false' indicates that disables DX.
It requires reboot after enablerw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.2.1.1 |
clCSCMXObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.3 |
clCSCMXServerConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.3.1 |
clCSCMXServerUrlThis object specifies the URL for cloud services
server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.3.1.1 |
clCSCMXServerIdTokenThis object specifies the token id for cloud services
server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.3.1.2 |
clCSCMXConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.3.2 |
clCSCMXEnableThis object specifies whether cloud services for
CMX is enabled or disabled.
A value of 'true' indicates that cloud services enables
for CMX.
A value of 'false' indicates that cloud services disables
for CMX.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.3.2.1 |
clCSCMXOnPremisesEnableThis object specifies whether NMSP service for on-premises
CMX is enabled or disabled.
A value of 'true' indicates that NMSP service is enabled for
on-premises CMX.
A value of 'false' indicates that NMSP service is disabled for
on-premises CMX.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.3.2.2 |
clCSSecTunObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.4 |
clCSSecTunConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.4.1 |
clCSSecTunEnableThis object specifies the status of secure tunnel
mode on the controller.
A value of 'true' indicates that, secure tunnel
is enabled.
A value of 'false' indicates that, secure tunnel
is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.4.1.1 |
clCSSecTunTlsGwFqdnThis object specifies the Fully Qualified Domain Name(FQDN)
of the TLS Gateway with which secure tunnel is established.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.2 |
clCSSecTunTlsGwIpAddrTypeThis object specifies the TLS Gateway IP
address type.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.3 |
clCSSecTunTlsGwIpAddrThis object specifies the IP address of the TLS
Gateway with which secure tunnel is established.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.4 |
clCSSecTunTlsGwPortThis object specifies the TLS Gateway port
number.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.5 |
clCSSecTunPskIdThis object specifies the PSK Id for the given WLC.
Id along with clCSSecTunPskKey are used as part of
secure tunnel setup with TLS gateway.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.6 |
clCSSecTunPskKeyThis object specifies the key of the PSK cipher,
which is used while setting up the secure tunnel
with TLS gatewayrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.7 |
clCSSecTunRadiusEnableThis object specifies the secure tunneling status of
RADIUS traffic like Authentication and Accounting servers.
A value of 'true' indicates that, RADIUS traffic on secure
tunnel is enabled.
A value of 'false' indicates that, RADIUS traffic on secure
tunnel is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.4.1.8 |
clCSSecTunSnmpTrapEnableThis object specifies the secure tunneling trap is
enabled or disabled.
A value of 'true' indicates that secure tunnel status
trap is enabled.
A value of 'false' indicates that secure tunnel status
trap is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.4.1.9 |
cLCSSecTunStaticNetworkTableThis table represents static Networks configured
for Secure tunneling of it's traffic. This is the
explicit way of configuration to send traffic of
a given network over TLS secure tunnel SEQUENCE OF CLCSSecTunStaticNetworkEntry .1.3.6.1.4.1.9.9.838.1.4.1.10 |
cLCSSecTunStaticNetworkEntryEach entry in this table represents the
attributes of secure tunnel network. CLCSSecTunStaticNetworkEntry .1.3.6.1.4.1.9.9.838.1.4.1.10.1 |
cLSCSecTunNetworkIPAddressTypeThis object specifies the IP address type
of cLSCSecTunNetworkIPAddress. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.10.1.1 |
cLSCSecTunNetworkIPAddressThis object specifies the IP address or subnet of
the network to be added for secure tunneling InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.10.1.2 |
cLSCSecTunNetworkIPNetmaskTypeThis object specifies IP netmask type of
cLSCSecTunNetworkIPNetmask. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.10.1.3 |
cLSCSecTunNetworkIPNetmaskThis object specifies the IP netmask of the
network added for secure tunneling. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.1.10.1.4 |
cLSCSecTunNetworkRowStatusThis object specifies status column for this
row and used to create and delete specific
instances of rows in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.4.1.10.1.5 |
clCSSecTunInfo OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.4.2 |
clCSSecTunCurrentStateThis object represents the current state of the
secure tunnel.
secureTunnelDown(1): This value indicates that secure tunnel
is down.
secureTunnelUp(2): This values indicates that secure tunnel
is up.ro Enumeration .1.3.6.1.4.1.9.9.838.1.4.2.1 |
clCSSecTunTlsGwIpAddrInUseTypeThis objects represents the TLS Gateway IP
address typero InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.2 |
clCSSecTunTlsGwIpInUseAddrThis object represents the IP address of the TLS Gateway
which is currently in-use. User can configure FQDN or
IP address for TLS Gateway. The preference is to resolve
the FQDN and get the IP address, if that fails it will
use the statically configured IP address.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.3 |
clCSSecTunInnerIpAddrTypeThis objects represents the IP address type
of the TLS client.ro InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.4 |
clCSSecTunInnerIpAddrThis object represents the inner IP address of the TLS
client on the controller. This IP is issued by TLS
gateway as part of the secure tunnel setup and informed
to TLS client as config update.ro InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.5 |
clCSSecTunTLSClientProcStateThis object represents the state of the TLS Client process.
TLS Client process is responsible in establishing TLS tunnel
with the Gateway. It encapsulates the data packets before
sending them to the Gateway over the tunnel.
tlscProcDown(1): This value indicates that the process
is down,
tlscProcInProg(2): This value indicates that the
process is just coming up and is in-progress.
tlscProcUp(3): This value indicates that the process
is up and running.
tlscProcReStart(4): This value indicates that the process
is in restart.ro Enumeration .1.3.6.1.4.1.9.9.838.1.4.2.6 |
cLCSSecTunRouteTableThis table represents the routes for various devices
and networks currently managed by the secure tunnel
module for tunneling of the management traffic. Plumbing
and deletion of the routes to linux occurs based on the
tunnel state changes. SEQUENCE OF CLCSSecTunRouteEntry .1.3.6.1.4.1.9.9.838.1.4.2.7 |
cLCSSecTunRouteEntryEach entry in this table represents attributes
needed for adding a route for secure tunneling CLCSSecTunRouteEntry .1.3.6.1.4.1.9.9.838.1.4.2.7.1 |
cLSCSecTunRouteIPAddressTypeThis object represents the IP address type
of cLSCSecTunRouteIPAddress. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.7.1.1 |
cLSCSecTunRouteIPAddressThis object represents the IP address or subnet
of the route to be added for secure tunneling InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.7.1.2 |
cLSCSecTunRouteNetmaskTypeThis object represents IP netmask type of
cLSCSecTunNetworkIPNetmask. InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.7.1.3 |
cLSCSecTunRouteNetmaskThis object represents the IP netmask of the
route to be added for secure tunneling. InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.838.1.4.2.7.1.4 |
cLSCSecTunRouteTableRowStatusThis object specifies the entry status
of this conceptual row.ro Unsigned32 .1.3.6.1.4.1.9.9.838.1.4.2.7.1.5 |
clCSWebhookGlobalObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.5 |
clCSWebhookUrlThis object specifies the URL for the webhook serverrw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.5.1 |
clCSWebhookAuthTokenThis object specifies the authentication token
of the webhook server.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.5.2 |
clCSWebhookEnableThis object specifies the state of the controller
telemetry data externalization to the webhook server.
A value of 'true' indicates that externalization
to the webhook server is enabled.
A value of 'false' indicates that externalization
to the webhook server is disabledrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.5.3 |
clCSWebhookOnchangeEnableThis object specifies the type of telemetry data that will be
externalized. The type can be bulk or onChange.
With onChange enabled, the server will
receive only the change in data.
With onChange disabled, the server will
receive the entire dataset(bulk)
A value of 'true' indicates that onchange is enabled.
A value of 'false' indicates that onChange is disabled.
clCSWebhookOnchangeEnable object is superseded by
clCSWebhookChannelOnChangeMode.rwdeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.5.4 |
clCSWebhookSyncIntervalThis object specifies the frequency
at which the telemetry data
would be received at the webhook server.
A value of fixed will provide data once in every 5 minutes
A value of adaptive will provide data once in 30 seconds
clCSWebhookSyncInterval object is superseded by
clCSWebhookChannelSyncInterval
.rwdeprecated Enumeration .1.3.6.1.4.1.9.9.838.1.5.5 |
clCSWebhookSubscriptionActionThis object specifies the possible
modifications to the data content
in the telemetry stream sent to the webhook server.
add - will add the channel to the telemetry stream
remove - will remove the channel from the telemetry stream
clCSWebhookSubscriptionAction object is superseded by
clCSWebhookChannelRowStatus.rwdeprecated Enumeration .1.3.6.1.4.1.9.9.838.1.5.6 |
clCSWebhookSubscriptionTopicThis object specifies the channels that can be modified
in the telemetry data stream that is
sent to the webhook server.
The user can configure a channel from the given enums
system(0) - Configures the system channel
network(1) - Configures the network channel
client(2) - Configures the client channel
ap(3) - Configures the AP channel
rogue(4) - Configures the rogue channel
interferer(5) - Configures the interferer channel
mapserver(6) - Configures the mapserver channel
clCSWebhookSubscriptionTopic object is superseded by
clCSWebhookChannelName.rwdeprecated Bits .1.3.6.1.4.1.9.9.838.1.5.7 |
cLCSWebhookResetSubscriptionsThis object specfies the option to reset webhook channel
subscriptions to defaults.
A value of 'true' indicates that subscriptions are reset.
A value of 'false' indicates that subscriptions are not reset.
User can only set the value 'true'.
Read on this object always returns the value 'false'.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.5.8 |
clCSWebhookTableObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.6 |
cLCSWebhookChannelTableThis table represents Webhook subscription channel
related configurations. SEQUENCE OF CLCSWebhookChannelEntry .1.3.6.1.4.1.9.9.838.1.6.1 |
cLCSWebhookChannelEntryEach entry in this table represents and includes the
attributes needed for subscribing a webhook channel CLCSWebhookChannelEntry .1.3.6.1.4.1.9.9.838.1.6.1.1 |
clCSWebhookChannelNameThis object specifies the webhook channel name
to subscribe/unsubscribe/set sync interval/set on-change
mode based on the value of respective objects.
'ap': This value indicates aps channel.
'ap-fra': This value indicates ap-fra channel.
'ap-capwap': This value indicates ap-capwap channel.
'ap-channel': This value indicates ap-channel channel.
'ap-fra-sensor': This value indicates ap-fra-sensor channel.
'ap-interface-stats': This value indicates ap-interface-stats
channel.
'ap-inventory': This value indicates ap-inventory channel.
'ap-network-stats': This value indicates ap-network-stats
channel.
'ap-reports': This value indicates ap-reports channel.
'ap-rf': This value indicates ap-rf channel.
'ap-rf-neighbors': This value indicates ap-rf-neighbors channel.
'ap-rf-stats': This value indicates ap-rf-stats channel.
'ap-events': This value indicates ap-events channel.
'ap-system': This value indicates ap-system channel.
'cdp': This value indicates cdp channel.
'client-app-stats': This value indicates client-app-stats
channel.
'client-mobility-stats': This value indicates
client-mobility-stats channel.
'client-network-stats': This value indicates
client-network-stats channel.
'client-policies': This value indicates client-policies channel.
'client-reports': This value indicates client-reports channel.
'client-rf-measurements': This value indicates
client-rf-measurements channel.
'client-traffic-measurements': This value indicates
client-traffic-measurements channel.
'client-wireless-stats': This value indicates
client-wireless-stats channel.
'client-dns-reports': This value indicates client-dns-reports
channel.
'client-events': This value indicates client-events channel.
'client': This value indicates clients channel.
'dhcp': This value indicates dhcp channel.
'eogre': This value indicates eogre channel.
'fabric': This value indicates fabric channel.
'interferers': This value indicates interferers channel.
'licensing': This value indicates licensing channel.
'mobility': This value indicates mobility channel.
'ndp': This value indicates ndp channel.
'radius-events': This value indicates radius-events channel.
'radius': This value indicates radius channel.
'redundancy-events': This value indicates redundancy-events
channel.
'redundancy': This value indicates redundancy channel.
'rogues': This value indicates rogues channel.
'system-core-stats': This value indicates system-core-stats
channel.
'system-dataplane-stats': This value indicates
system-dataplane-stats channel.
'system-general-stats': This value indicates
system-general-stats channel.
'system-port-stats': This value indicates system-port-stats
channel.
'system-process-stats': This value indicates
system-process-stats channel.
'tacacs': This value indicates tacacs channel. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.6.1.1.1 |
clCSWebhookChannelSyncIntervalThis object specifies the webhook channel sync interval.
fifteen(15): This value indicates 15 sec interval
thirty(30): This value indicates 30 sec interval
sixty(60): This value indicates 60 sec interval
threehundred(300): This value indicates 300 sec interval.rw Enumeration .1.3.6.1.4.1.9.9.838.1.6.1.1.2 |
clCSWebhookChannelOnChangeModeThis object specifies the value of on-change mode
of a webhook server channel.
A value of 'true' indicates that only changed data will be
synced.
A value of 'false' indicates that all the data present
in DB will be synced.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.6.1.1.3 |
clCSWebhookChannelRowStatusThis is the status column for this row and is used to
create and delete specific instances of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.6.1.1.4 |
clCSFilterChanTableObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.1.7 |
cLCSTelemetryFCTableThis table represents telemetry filter channel
related configurations. Filter channel is a user
created channel which uses filters added by user
to externalize the data. SEQUENCE OF CLCSTelemetryFCEntry .1.3.6.1.4.1.9.9.838.1.7.1 |
cLCSTelemetryFCEntryEach entry in this table represents the attributes
needed for managing a filter channel. CLCSTelemetryFCEntry .1.3.6.1.4.1.9.9.838.1.7.1.1 |
clCSTelemetryFCNameThis object specifies the name of filter channel. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.7.1.1.1 |
clCSTelemetryFCParentThis object specifies the name of parent channel to which
the filter channel belongs. Parent channel should be
a static channel.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.7.1.1.2 |
clCSTelemetryFCSubStatusThis object represents whether the filter channel is
subscribed or not.
none(1): This value indicates that filter channel is
not subscribed.
assurance(2): This value indicates that filter channel
is subscribed to assurance.
webhook(3): This value indicates that filter channel
is subscribed to webhook.ro Enumeration .1.3.6.1.4.1.9.9.838.1.7.1.1.3 |
clCSTelemetryFCFilterCountThis object represents the number of filters configured
on this filter channel.ro Unsigned32 .1.3.6.1.4.1.9.9.838.1.7.1.1.4 |
clCSTelemetryFCRowStatusThis is the status column for this row and is used to
create and delete specific instances of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.7.1.1.5 |
cLCSTelemetryFCFilterTableThis table represents all the filters configured on the
filter channels. SEQUENCE OF CLCSTelemetryFCFilterEntry .1.3.6.1.4.1.9.9.838.1.7.2 |
cLCSTelemetryFCFilterEntryEach entry in this table represents the attributes
needed for managing the filters of a perticular filter
channel CLCSTelemetryFCFilterEntry .1.3.6.1.4.1.9.9.838.1.7.2.1 |
clCSTelemetryFCFilterThis object specifies the filters of a given filter channel.
Filter channel extracts the data from parent channel
based on the provided filters. SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.9.838.1.7.2.1.1 |
clCSTelemetryFCFilterRowStatusThis is the status column for this row and is used to
create and delete specific instances of rows in this
table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.838.1.7.2.1.2 |
clCSMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.2 |
clCSMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.2.1 |
clCSMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.838.2.2 |