CISCO-IPSLA-JITTER-MIB
AI MIB Summary
The CISCO-IPSLA-JITTER-MIB enables Cisco IOS devices to monitor and retrieve UDP and ICMP Jitter operation statistics, specifically measuring round-trip time, one-way latency, delay variance, and packet loss for synthetic traffic streams.
This MIB module defines templates for IP SLA operations of UDP Jitter and ICMP Jitter.
The UDP Jitter operation is designed to measure the delay variance and packet loss in IP networks by generating synthetic UDP traffic.
The ICMP Jitter operation provides capability to measure metrics such as RTT (Round Trip Time), jitter, packet loss, one-way latency by sending ICMP Timestamp stream to the destination devices.
Main OID:
ciscoIpSlaJitterMIB.1.3.6.1.4.1.9.9.635
55
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
55 total| Object Name |
|---|
ciscoIpSlaJitterMIBThis MIB module defines templates for IP SLA operations of UDP
Jitter and ICMP Jitter.
The UDP Jitter operation is designed to measure the delay
variance and packet loss in IP networks by generating synthetic
UDP traffic.
The ICMP Jitter operation provides capability to measure metrics
such as RTT (Round Trip Time), jitter, packet loss, one-way
latency by sending ICMP Timestamp stream to the destination
devices. MODULE-IDENTITY .1.3.6.1.4.1.9.9.635 |
ciscoIpSlaJitterMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.635.0 |
ciscoIpSlaJitterMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.635.1 |
cipslaUdpJitterTmplTableA table that contains UDP jitter template specific definitions. SEQUENCE OF CipslaUdpJitterTmplEntry .1.3.6.1.4.1.9.9.635.1.1 |
cipslaUdpJitterTmplEntryA row entry representing an IPSLA UDP jitter template. CipslaUdpJitterTmplEntry .1.3.6.1.4.1.9.9.635.1.1.1 |
cipslaUdpJitterTmplNameA string which specifies the UDP Jitter template name. SnmpAdminString .1.3.6.1.4.1.9.9.635.1.1.1.1 |
cipslaUdpJitterTmplDescriptionA string which provides description of UDP Jitter
template.rw SnmpAdminString .1.3.6.1.4.1.9.9.635.1.1.1.2 |
cipslaUdpJitterTmplControlEnableIf this object is enabled, then the IP SLA application
will send control messages to a responder, residing on the
target router to respond to the data request packets being
sent by the source router.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.1.1.3 |
cipslaUdpJitterTmplTimeOutSpecifies the duration to wait for a IP SLA operation
completion.
For connection oriented protocols, this may cause the
connection to be closed by the operation. Once closed, it
will be assumed that the connection reestablishment
will be performed. To prevent unwanted closure of
connections, be sure to set this value to a realistic
connection timeout.rw Unsigned32 (0..604800000 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.1.1.4 |
cipslaUdpJitterTmplVerifyDataWhen set to true, the resulting data in each IP SLA
operation is compared with the expected data. This
includes checking header information (if possible) and
exact packet size.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.1.1.5 |
cipslaUdpJitterTmplCodecTypeSpecifies the codec type to be used with UDP jitter operation.
If codec-type is configured the following parameters cannot be
configured.
cipslaUdpJitterReqDataSize
cipslaUdpJitterInterval
cipslaUdpJitterNumPktsrw IpSlaCodecType (CISCO-IPSLA-TC-MIB) .1.3.6.1.4.1.9.9.635.1.1.1.6 |
cipslaUdpJitterTmplCodecIntervalThis field represents the inter-packet delay between
packets and is in milliseconds. This object is applicable
only to UDP jitter operation which uses codec type.rw Unsigned32 (4..60000 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.1.1.7 |
cipslaUdpJitterTmplCodecPayloadThis object represents the number of octets that needs to be
placed into the Data portion of the message. This value is
used only for UDP jitter operation which uses codec type.rw Unsigned32 (0..16384 ) UNITS "octets" .1.3.6.1.4.1.9.9.635.1.1.1.8 |
cipslaUdpJitterTmplCodecNumPktsThis value represents the number of packets that need to
be transmitted. This value is used only for UDP jitter
operation which uses codec type.rw Unsigned32 (1..60000 ) UNITS "packets" .1.3.6.1.4.1.9.9.635.1.1.1.9 |
cipslaUdpJitterTmplIntervalThis value represents the inter-packet delay between packets
and is in milliseconds.rw Unsigned32 (4..60000 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.1.1.10 |
cipslaUdpJitterTmplNumPktsThis value represents the number of packets that need to be
transmitted.rw Unsigned32 (1..60000 ) UNITS "packets" .1.3.6.1.4.1.9.9.635.1.1.1.11 |
cipslaUdpJitterTmplSrcAddrTypeAn enumerated value which specifies the IP address type
of the source. It must be used along with the
cipslaUdpJitterTmplSrcAddr object.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.635.1.1.1.12 |
cipslaUdpJitterTmplSrcAddrThis field specifies the IP address of the source.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.635.1.1.1.13 |
cipslaUdpJitterTmplSrcPortThis object represents the source's port number. If this
object is not specified, the application will get a
port allocated by the system.rw InetPortNumber (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.635.1.1.1.14 |
cipslaUdpJitterTmplPrecisionThis object specifies the accuracy of jitter statistics in
rttMonJitterStatsTable that needs to be calculated.
milliseconds(1) - The accuracy of stats will be of milliseconds.
microseconds(2) - The accuracy of stats will be in microseconds.rw Enumeration .1.3.6.1.4.1.9.9.635.1.1.1.15 |
cipslaUdpJitterTmplReqDataSizeThis object represents the number of octets to be
placed into the ARR Data portion of the request
message, when using SNA protocols.
For non-ARR protocols' IP SLA request/responses,
this value represents the native payload size.
REMEMBER: The ARR Header overhead is not included
in this value.rw Unsigned32 (16..65024 ) UNITS "octets" .1.3.6.1.4.1.9.9.635.1.1.1.16 |
cipslaUdpJitterTmplPktPriorityThis object specifies the priority that will be assigned
to operation packet.
normal(1) - The packet is of normal priority.
high(2) - The packet is of high priority.rw Enumeration .1.3.6.1.4.1.9.9.635.1.1.1.17 |
cipslaUdpJitterTmplTOSThis object represents the type of service octet in an
IP header.rw Unsigned32 (0..255 ) .1.3.6.1.4.1.9.9.635.1.1.1.18 |
cipslaUdpJitterTmplVrfNameThis field is used to specify the VRF name in
which the IP SLA operation will be used. For regular IP SLA
operation this field should not be configured. The agent
will use this field to identify the VPN routing table for
this operation.rw SnmpAdminString .1.3.6.1.4.1.9.9.635.1.1.1.19 |
cipslaUdpJitterTmplThresholdThis object defines an administrative threshold limit.
If the IP SLA operation time exceeds this limit, then
one threshold crossing occurrence will be counted.rw Unsigned32 (0..2147483647 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.1.1.20 |
cipslaUdpJitterTmplNTPTolAbsThis object specifies the total clock synchronization error
on source and responder that is considered tolerable for
oneway measurement when NTP is used as clock synchronization
mechanism. The total clock synchronization error is sum of
NTP offsets on source and responder. The value specified is
microseconds. This value can be set only for UDP jitter operation
with precision of microsecond.rw Unsigned32 (0..100000 ) UNITS "microseconds" .1.3.6.1.4.1.9.9.635.1.1.1.21 |
cipslaUdpJitterTmplNTPTolPctThis object specifies the total clock synchronization error
on source and responder that is considered tolerable for
oneway measurement when NTP is used as clock synchronization
mechanism. The total clock synchronization error is sum of
NTP offsets on source and responder. The value is expressed
as the percentage of actual oneway latency that is measured.
This value can be set only for UDP jitter operation with precision
of microsecond.rw Unsigned32 (0..100 ) .1.3.6.1.4.1.9.9.635.1.1.1.22 |
cipslaUdpJitterTmplNTPTolTypeThis object specifies whether the value specified for oneway
NTP sync tolerance is absolute value or percent value.
percent(1) - The value for oneway NTP sync tolerance is
absolute value.
absolute(2) - The value for oneway NTP sync tolerance is
percent value.rw Enumeration .1.3.6.1.4.1.9.9.635.1.1.1.23 |
cipslaUdpJitterTmplIcpifFactorThe advantage factor is dependant on the type of access and
how the service is to be used.
Conventional Wire-line 0
Mobility within Building 5
Mobility within geographic area 10
Access to hard-to-reach location 20
It is used when calculating the ICPIF value.rw Unsigned32 (0..20 ) .1.3.6.1.4.1.9.9.635.1.1.1.24 |
cipslaUdpJitterTmplStatsHoursThe maximum number of hours for which statistics are
maintained. Specifically this is the number of hourly
groups to keep before rolling over.
The value of one is not advisable because the hourly
group will close and immediately be deleted before
the network management station will have the
opportunity to retrieve the statistics.
The value of zero will shut off data collection.rw Unsigned32 (0..25 ) UNITS "hours" .1.3.6.1.4.1.9.9.635.1.1.1.25 |
cipslaUdpJitterTmplDistBucketsThe maximum number of statistical distribution
buckets to accumulate.
Since this index does not rollover, only the first
cipslaUdpJitterTmplDistBuckets will be kept.
The last bucket will contain all entries from its
distribution interval start point to infinity.rw Unsigned32 (1..20 ) .1.3.6.1.4.1.9.9.635.1.1.1.26 |
cipslaUdpJitterTmplDistIntervalThe statistical distribution buckets interval.
Distribution Bucket Example:
cipslaUdpJitterTmplDistBuckets = 5 buckets
cipslaUdpJitterTmplDistInterval = 10 milliseconds
| Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 |
| 0-9 ms | 10-19 ms | 20-29 ms | 30-39 ms | 40-Inf ms |
Odd Example:
cipslaUdpJitterTmplDistBuckets = 1 buckets
cipslaUdpJitterTmplDistInterval = 10 milliseconds
| Bucket 1 |
| 0-Inf ms |
Thus, this odd example shows that the value of
cipslaUdpJitterTmplDistInterval does not apply when
cipslaUdpJitterTmplDistBuckets is one.rw Unsigned32 (1..100 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.1.1.27 |
cipslaUdpJitterTmplStorageTypeThe storage type of this conceptual row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.1.1.28 |
cipslaUdpJitterTmplRowStatusThe status of the conceptual UDP Jitter template control row.
When the status is active, all the read-create objects in that
row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.1.1.30 |
cipslaIcmpJitterTmplTableA table that contains ICMP jitter template specific definitions. SEQUENCE OF CipslaIcmpJitterTmplEntry .1.3.6.1.4.1.9.9.635.1.2 |
cipslaIcmpJitterTmplEntryA row entry representing an IP SLA ICMP Jitter template. CipslaIcmpJitterTmplEntry .1.3.6.1.4.1.9.9.635.1.2.1 |
cipslaIcmpJitterTmplNameA string which specifies the ICMP jitter template name. SnmpAdminString .1.3.6.1.4.1.9.9.635.1.2.1.1 |
cipslaIcmpJitterTmplDescriptionA string which provides description of ICMP Jitter
template.rw SnmpAdminString .1.3.6.1.4.1.9.9.635.1.2.1.2 |
cipslaIcmpJitterTmplTimeOutSpecifies the duration to wait for a IP SLA operation
completion.
For connection oriented protocols, this may cause the
connection to be closed by the operation. Once closed, it
will be assumed that the connection reestablishment
will be performed. To prevent unwanted closure of
connections, be sure to set this value to a realistic
connection timeout.rw Unsigned32 (0..604800000 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.2.1.3 |
cipslaIcmpJitterTmplVerifyDataWhen set to true, the resulting data in each IP SLA
operation is compared with the expected data. This
includes checking header information (if possible) and
exact packet size.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.2.1.4 |
cipslaIcmpJitterTmplNumPktsThis value represents the number of packets that need to be
transmitted.rw Unsigned32 (1..60000 ) UNITS "packets" .1.3.6.1.4.1.9.9.635.1.2.1.5 |
cipslaIcmpJitterTmplIntervalThis value represents the inter-packet delay between packets
and is in milliseconds.rw Unsigned32 (4..60000 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.2.1.6 |
cipslaIcmpJitterTmplSrcAddrTypeAn enumerated value which specifies the IP address type
of the source. It must be used along with the
cipslaIcmpJitterTmplSrcAddr object.rw InetAddressType (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.635.1.2.1.7 |
cipslaIcmpJitterTmplSrcAddrA string which specifies the IP address of the source.rw InetAddress (INET-ADDRESS-MIB) .1.3.6.1.4.1.9.9.635.1.2.1.8 |
cipslaIcmpJitterTmplTOSThis object represents the type of service octet in an
IP header.rw Unsigned32 (0..255 ) .1.3.6.1.4.1.9.9.635.1.2.1.9 |
cipslaIcmpJitterTmplVrfNameThis field is used to specify the VRF name in
which the IP SLA operation will be used. For regular IP SLA
operation this field should not be configured. The agent
will use this field to identify the VPN routing Table for
this operation.rw SnmpAdminString .1.3.6.1.4.1.9.9.635.1.2.1.10 |
cipslaIcmpJitterTmplThresholdThis object defines an administrative threshold limit.
If the IP SLA operation time exceeds this limit, then
one threshold crossing occurrence will be counted.rw Unsigned32 (0..2147483647 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.2.1.11 |
cipslaIcmpJitterTmplStatsHoursThe maximum number of hourss for which statistics are
maintained. Specifically this is the number of hourly
groups to keep before rolling over.
The value of one is not advisable because the hourly
group will close and immediately be deleted before
the network management station will have the
opportunity to retrieve the statistics.
The value of zero will shut off data collection.rw Unsigned32 (0..25 ) UNITS "hours" .1.3.6.1.4.1.9.9.635.1.2.1.12 |
cipslaIcmpJitterTmplDistBucketsThe maximum number of statistical distribution
buckets to accumulate.
Since this index does not rollover, only the first
cipslaIcmpJitterTmplDistBuckets will be kept.
The last bucket will contain all entries from its
distribution interval start point to infinity.rw Unsigned32 (1..20 ) .1.3.6.1.4.1.9.9.635.1.2.1.13 |
cipslaIcmpJitterTmplDistIntervalThe statistical distribution buckets interval.
Distribution Bucket Example:
cipslaIcmpJitterTmplDistBuckets = 5 buckets
cipslaIcmpJitterTmplDistInterval = 10 milliseconds
| Bucket 1 | Bucket 2 | Bucket 3 | Bucket 4 | Bucket 5 |
| 0-9 ms | 10-19 ms | 20-29 ms | 30-39 ms | 40-Inf ms |
Odd Example:
cipslaIcmpJitterTmplDistBuckets = 1 buckets
cipslaIcmpJitterTmplDistInterval = 10 milliseconds
| Bucket 1 |
| 0-Inf ms |
Thus, this odd example shows that the value of
cipslaIcmpJitterTmplDistInterval does not apply when
cipslaIcmpJitterTmplDistBuckets is one.rw Unsigned32 (1..100 ) UNITS "milliseconds" .1.3.6.1.4.1.9.9.635.1.2.1.14 |
cipslaIcmpJitterTmplStorageTypeThe storage type of this conceptual row.rw StorageType (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.2.1.15 |
cipslaIcmpJitterTmplRowStatusThe status of the conceptual ICMP jitter template control row.
When the status is active, all the read-create objects in
that row can be modified.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.635.1.2.1.16 |
ciscoIpSlaJitterMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.635.2 |
ciscoIpSlaJitterMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.635.2.1 |
ciscoIpSlaJitterMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.635.2.2 |