Home/Catalog/CISCO-IP-RAN-BACKHAUL-MIB

CISCO-IP-RAN-BACKHAUL-MIB

AI MIB Summary

The CISCO-IP-RAN-BACKHAUL-MIB monitors traffic volume, compression efficiency, and error statistics for GSM (A-bis) and UMTS (Iub) backhaul links connecting Base Transceiver Systems (BTS) and Node Bs to Base Station Controllers (BSC) and Radio Network Controllers (RNC). It specifically tracks performance metrics for legacy transport protocols including PPP multilink, ATM, and IMA, alongside IP cloud transport, to facilitate optimization of the Radio Access Network (RAN) infrastructure.

This MIB provides information on the IP-RAN traffic from cell site to aggregation site in the following situations. In an GSM environment the cell site will be the Base station Transceiver System(BTS) and the aggregation site will be the Base Station Controller(BSC). In the UMTS environment the cell site will be the B-Node and the aggregation site will Radio Network Controller(RNC). There are two typical type backhaul, also know as longhaul, links. The traditional backhaul connection consists of a PPP multilink containing two or more E1 or T1 links or ATM or ATM/IMA. The alternate backhaul is traffic transported using IP cloud. Simple back-to-back configuration - This setup consists of two devices that support a limited number of GSM and UMTS links. They are deployed in pairs and inserted between the existing BTS device and BSC device. BTS site BSC site GSM-Abis GSM-Abis |||||||| Backhaul |||||||| | | | | |||||||| |||||||| RNC B-Node site RNC UMTS UMTS |||||||| Backhaul |||||||| | | | | |||||||| |||||||| | | | Alternate backhaul over IP cloud Aggregate node configuration This configuration consists of one aggregate node located at BSC site and several devices at BTS sites. The aggregate device has a seperate backhaul link to each BTS site. BTS site BSC site Aggregate GSM GSM |||||||| Backhaul |||||||| | | | | |||||||| | | . | | . . | | . GSM . | | . |||||||| Backhaul | | | | | | |||||||| |||||||| RNC B-Node UMTS UMTS |||||||| Backhaul |||||||| | | | | |||||||| | | | Alternate | | | .... | | . IP . | | . Cloud.-| | . . | | | ...... | | | Backhaul | | UMTS | | | |||||||| Backhaul | | | | | | |||||||| |||||||| Compression Multiplexing | BSC <>BTS . GSM . | |<>| | . GSM . . A(bis) . | |<>| | . A(bis) . <> A A | | ShortHaul BackHaul Multiple E1/T1 Back Haul Links Entries in these tables cannot be created or deleted by the network management system. All entries are created or deleted by the agent. Shorthaul interfaces support the following protocols. Protocol ifType GSM-Abis propPointToPointSerial(22) UMTS-iub atm(37) UMTS/IMA atmSubInterface(134) aal5(49) ifType.44 = atmIma(107) The following list provides the currently allowed backhaul interfaces types. Additional interfaces types will be added as they are supported. ifType ethernetCsmacd(6) ppp(23) as Multilink bundle pppMultilinkBundle(108) In order to manage the IP-RAN optimization solution, two key factors must be monitored. The first and most important is the amount of traffic sent over the backhaul interface. The second is compression efficiency which has a direct impact amount of traffic placed backhaul link. MIB Structure - The MIB has the following structure. Shorthaul information tables: cirbhInfoTable Shorthaul Alarm Information tables cirbhGsmAlarmTable cirbhUmtsConnectionTable cirbhUmtsAlarmTable Shorthaul statistics tables cirbhStatsTable cirbhErrorsTable(deprecated) cirbhShortHaulHistoryTable(obsolete) cirbhCongestionTable cirbhGsmErrorsTable(replaces cirbhErrorsTable) cirbhUmtsErrorsTable(replaces cirbhErrorsTable) Backhaul information tables cirbhBackHaulTable(obsolete) Backhaul statistics tables cirbhBackHaulHistoryTable(obsolete) cirbhBackHaulStatsTable(obsolete) cirbhBackHaulStatsHistoryTable(deprecated) Abbreviations: A-bis Interface between BSC and BTS AAL2 ATM Adaptation Layer type 2 AAL5 ATM Adaptation Layer type 5 AIM Advanced Interface Module AgNode Aggregation Node ALCAP Access Link Control Application Part AMR Adaptive Multi-Rate speech codec ATM Asynchronous Transfer Mode BCH Broadcast Channel BSC Base Station Controller. BTS Base Station Transceiver System CDF CID Definition Field CID Channel IDentification CPCH Common Packet Channel DCH Dedicated Channel DSCH Downlink Shared Channel DTX Discontinuous Transmission (mechanism) FACH Forward Link Access Channel GSM Global System for Mobile communications IMA Inverse Multiplexing for ATM Iub Node B to RNC interface OC3 Optical Carrier 3 OSF OffSet Field LAPD Link Access Protocol on Dm Channel O&M Operations and Maintenance MLPPP Multi-Link PPP MS Mobile Station (Handset) NBAP Node B Application Part NNI Network to Network Interface Node-B Node B PCH Paging Channel PVC Permanent Virtual Circuit RAN Radio Access Network SVC Switched Virtual Circuit RACH Random Access Channel RNC Radio Network Controller SAR Segment Assembly Reassembly SDC Traffic Channel SDH Signaling Channel SPVC Soft Permanent Virtual Circuit SSCOP Service Specific Connection Oriented Protocol STC Signaling Transport Converter STM-1 Synchronous Transport Module type 1 TRAU Transcoder Unit UMTS Universal Mobile Telecommunications System UNI User to Network Interface USCH Uplink Shared Channel UTRAN UMTS Terrestrial Radio Access Network VCI Virtual Channel Identifier VPI Virtual Path Identifier
Main OID:
ciscoIpRanBackHaulMIB.1.3.6.1.4.1.9.9.483
216
Objects
Active
Status
8
Dependencies

Imported Objects

SNMPv2-CONF
SNMPv2-SMI
INET-ADDRESS-MIB
IF-MIB
PerfHist-TC-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-TC
CISCO-SMI

Objects

216 total
Object Name
ciscoIpRanBackHaulMIBThis MIB provides information on the IP-RAN traffic from cell site to aggregation site in the following situations. In an GSM environment the cell site will be the Base station Transceiver System(BTS) and the aggregation site will be the Base Station Controller(BSC). In the UMTS environment the cell site will be the B-Node and the aggregation site will Radio Network Controller(RNC). There are two typical type backhaul, also know as longhaul, links. The traditional backhaul connection consists of a PPP multilink containing two or more E1 or T1 links or ATM or ATM/IMA. The alternate backhaul is traffic transported using IP cloud. Simple back-to-back configuration - This setup consists of two devices that support a limited number of GSM and UMTS links. They are deployed in pairs and inserted between the existing BTS device and BSC device. BTS site BSC site GSM-Abis GSM-Abis |||||||| Backhaul |||||||| | | | | |||||||| |||||||| RNC B-Node site RNC UMTS UMTS |||||||| Backhaul |||||||| | | | | |||||||| |||||||| | | | Alternate backhaul over IP cloud Aggregate node configuration This configuration consists of one aggregate node located at BSC site and several devices at BTS sites. The aggregate device has a seperate backhaul link to each BTS site. BTS site BSC site Aggregate GSM GSM |||||||| Backhaul |||||||| | | | | |||||||| | | . | | . . | | . GSM . | | . |||||||| Backhaul | | | | | | |||||||| |||||||| RNC B-Node UMTS UMTS |||||||| Backhaul |||||||| | | | | |||||||| | | | Alternate | | | .... | | . IP . | | . Cloud.-| | . . | | | ...... | | | Backhaul | | UMTS | | | |||||||| Backhaul | | | | | | |||||||| |||||||| Compression Multiplexing | BSC <>BTS . GSM . | |<>| | . GSM . . A(bis) . | |<>| | . A(bis) . <> A A | | ShortHaul BackHaul Multiple E1/T1 Back Haul Links Entries in these tables cannot be created or deleted by the network management system. All entries are created or deleted by the agent. Shorthaul interfaces support the following protocols. Protocol ifType GSM-Abis propPointToPointSerial(22) UMTS-iub atm(37) UMTS/IMA atmSubInterface(134) aal5(49) ifType.44 = atmIma(107) The following list provides the currently allowed backhaul interfaces types. Additional interfaces types will be added as they are supported. ifType ethernetCsmacd(6) ppp(23) as Multilink bundle pppMultilinkBundle(108) In order to manage the IP-RAN optimization solution, two key factors must be monitored. The first and most important is the amount of traffic sent over the backhaul interface. The second is compression efficiency which has a direct impact amount of traffic placed backhaul link. MIB Structure - The MIB has the following structure. Shorthaul information tables: cirbhInfoTable Shorthaul Alarm Information tables cirbhGsmAlarmTable cirbhUmtsConnectionTable cirbhUmtsAlarmTable Shorthaul statistics tables cirbhStatsTable cirbhErrorsTable(deprecated) cirbhShortHaulHistoryTable(obsolete) cirbhCongestionTable cirbhGsmErrorsTable(replaces cirbhErrorsTable) cirbhUmtsErrorsTable(replaces cirbhErrorsTable) Backhaul information tables cirbhBackHaulTable(obsolete) Backhaul statistics tables cirbhBackHaulHistoryTable(obsolete) cirbhBackHaulStatsTable(obsolete) cirbhBackHaulStatsHistoryTable(deprecated) Abbreviations: A-bis Interface between BSC and BTS AAL2 ATM Adaptation Layer type 2 AAL5 ATM Adaptation Layer type 5 AIM Advanced Interface Module AgNode Aggregation Node ALCAP Access Link Control Application Part AMR Adaptive Multi-Rate speech codec ATM Asynchronous Transfer Mode BCH Broadcast Channel BSC Base Station Controller. BTS Base Station Transceiver System CDF CID Definition Field CID Channel IDentification CPCH Common Packet Channel DCH Dedicated Channel DSCH Downlink Shared Channel DTX Discontinuous Transmission (mechanism) FACH Forward Link Access Channel GSM Global System for Mobile communications IMA Inverse Multiplexing for ATM Iub Node B to RNC interface OC3 Optical Carrier 3 OSF OffSet Field LAPD Link Access Protocol on Dm Channel O&M Operations and Maintenance MLPPP Multi-Link PPP MS Mobile Station (Handset) NBAP Node B Application Part NNI Network to Network Interface Node-B Node B PCH Paging Channel PVC Permanent Virtual Circuit RAN Radio Access Network SVC Switched Virtual Circuit RACH Random Access Channel RNC Radio Network Controller SAR Segment Assembly Reassembly SDC Traffic Channel SDH Signaling Channel SPVC Soft Permanent Virtual Circuit SSCOP Service Specific Connection Oriented Protocol STC Signaling Transport Converter STM-1 Synchronous Transport Module type 1 TRAU Transcoder Unit UMTS Universal Mobile Telecommunications System UNI User to Network Interface USCH Uplink Shared Channel UTRAN UMTS Terrestrial Radio Access Network VCI Virtual Channel Identifier VPI Virtual Path Identifier
MODULE-IDENTITY
.1.3.6.1.4.1.9.9.483
ciscoIpRanBackHaulMIBNotifs
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.0
ciscoIpRanBackHaulGsmAlarmThis notification is generated whenever the values of the specified objects change.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.483.0.1
ciscoIpRanBackHaulUmtsAlarmThis notification is generated whenever the values of the specified objects change.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.483.0.2
ciscoIpRanBackHaulRcvdUtilThis notification is generated once for the interval specified by the cirbhBackHaulStatsInterval object for the following state transitions. 'acceptable' -> 'warning' 'acceptable' -> 'overloaded' 'warning' -> 'overloaded' At the end of the interval specified by the cirbhBackHaulUtilInterval object another notification will be generated if the current state is different from state sent in last notification.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.483.0.3
ciscoIpRanBackHaulSentUtilThis notification is generated once for the interval specified by the cirbhBackHaulStatsInterval object for the following state transitions. 'acceptable' -> 'warning' 'acceptable' -> 'overloaded' 'warning' -> 'overloaded' At the end of the interval specified by the cirbhBackHaulUtilInterval object another notification will be generated if the current state is different from state sent in last notification.
NOTIFICATION-TYPE
.1.3.6.1.4.1.9.9.483.0.4
ciscoIpRanBackHaulMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1
cirbhScalars
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.1
cirbhSnmpTrafficModeThis object describes the mode of SNMP traffic for this device in relationship to connectivity to network management station. This will be used to define default behavior for the device based on the on available bandwidth for management. 'undefined' : Traffic mode is not defined. 'inBand' : SNMP traffic uses same physical interfaces as voice traffic. 'outOfBand' : SNMP traffic does not use same physical interfaces as voice traffic.rw
Enumeration
.1.3.6.1.4.1.9.9.483.1.1.1
cirbhLocationThis object provides information on location of the device to aid in topology display. 'undefined' : not defined. 'aggSite' : Located at Base Station Controller or or Radio Network Controller site. 'cellSite' : Located at Base Station Transceiver System or Node B site.rw
Enumeration
.1.3.6.1.4.1.9.9.483.1.1.2
cirbhBackHaulStatsIntervalThe length of the interval used to collect statistics in the cirbhBackHaulStatsTable.rwdeprecated
Unsigned32
.1.3.6.1.4.1.9.9.483.1.1.3
cirbhBackHaulStatsEntriesThe maximum number of entries in the cirbhBackHaulStatsTable table.rwdeprecated
Unsigned32
.1.3.6.1.4.1.9.9.483.1.1.4
cirbhBackHaulAcceptableThresholdThis object is used to specify a level of traffic below which the instances of the cirbhBackHaulRcvdUtilState and cirbhBackHaulSentUtilState objects are marked as 'acceptable'. All changes to this threshold will take effect at the end of the current interval. The value for this object must be less than the values specified by cirbhBackHaulOverloadedThreshold and cirbhBackHaulWarningThreshold objects.rwdeprecated
Unsigned32
.1.3.6.1.4.1.9.9.483.1.1.5
cirbhBackHaulWarningThresholdThis object is used to specify a level of traffic were the instances of the cirbhBackHaulRcvdUtilState and cirbhBackHaulSentUtilState objects are marked as 'warning'. All changes to this threshold will take effect at the end of the current interval. The value for this object must be greater than the value specified for the cirbhBackHaulAcceptableThreshold object. Also, the value for this object must be less than or equal to value of the cirbhBackHaulOverloadedThreshold object.rwdeprecated
Unsigned32
.1.3.6.1.4.1.9.9.483.1.1.6
cirbhBackHaulOverloadedThresholdThis object is used to specify a level of traffic were the instances of the cirbhBackHaulRcvdUtilState and cirbhBackHaulSentUtilState objects are marked as 'overloaded'. Changes to this threshold will take effect at the end of the current interval. The value for this object must be greater than the value specified for the cirbhBackHaulAcceptableThreshold object. Also, the value for this object must be greater than or equal to value of the cirbhBackHaulWarningThreshold object. This object will be used to determine the state of the cirbhBackHaulRcvdUtilState and cirbhBackHaulSentUtilState objects.rwdeprecated
Unsigned32
.1.3.6.1.4.1.9.9.483.1.1.7
cirbhBackHaulUtilIntervalThe length of the interval used to suppress generation of the ciscoIpRanBackHaulRcvdUtil and ciscoIpRanBackHaulSentUtil notifications. Notification will not be suppressed when zero value is specified.rwdeprecated
Unsigned32 (0 | 60..3600) UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.1.8
cirbhObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2
cirbhShortHaul
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.1
cirbhShortHaulInfo
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.1.1
cirbhInfoTableThis table provides information on interface used to establish shorthaul connection to BTS or BSC or node B site.
SEQUENCE OF CirbhInfoTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.1.1
cirbhInfoTableEntryEach entry describes the information used to route GSM and UMTS packets across backhaul for a single GSM or UMTS link.
CirbhInfoTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1
cirbhInfoProtocolProtocol used to indicate type of shorthaul.ro
CirbhProtocol
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.1
cirbhInfoLocalAddrTypeThe type of address specified in the corresponding instance of cirbhConfigLocalIpAddr object.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.2
cirbhInfoLocalAddrThe local address used to route traffic across backhaul.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.3
cirbhInfoLocalPortNumberThe local port number used to distinguish traffic from this interface when transported over backhaul connection.ro
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.4
cirbhInfoRemoteAddrTypeThe type of address in the in the corresponding instance of the cirbhInfoRemoteAddr object.ro
InetAddressType (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.5
cirbhInfoRemoteAddrThe remote IP address used to route traffic across backhaul.ro
InetAddress (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.6
cirbhInfoRemotePortNumberThe remote port number used to distinguish traffic from this interface when transported over backhaul connection.ro
InetPortNumber (INET-ADDRESS-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.7
cirbhInfoAdjectSerialNumThis object provides the serial number of the adjacent device supporting the other side of this shorthaul. This object contains the same value as the corresponding entPhysicalSerialNum object on the adjacent device. The type of object like chassis or module is provided by the cirbhInfoAdjectVendorType object.ro
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.8
cirbhInfoAdjectVendorTypeThis object provides the vendor type of the adjacent device supporting other end of this shorthaul. This objectcontains the same value as the corresponding entPhysicalVendorType object on the adjacent device.ro
AutonomousType (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.9
cirbhInfoBackhaulRxIfIndexThis object provides the ifIndex of the interface used to receive traffic from destination.ro
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.10
cirbhInfoBackhaulTxIfIndexThis object provides the ifIndex of the interface used to sent traffic to destination.ro
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.11
cirbhInfoShBulkLastIndexThe latest value of the cirbhShortHaulBulkHistory object from the cirbhShortHaulBulkHistory table.ro
CirbhHistoryIndex
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.12
cirbhInfoOptimizeTrafficThis object indicate whether the traffic received and sent for this shorthaul interface is optimized.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.1.1.1.13
cirbhShortHaulAlarmInfo
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.1.2
cirbhGsmAlarmTableThis table provides alarm information for GSM-Abis interfaces.
SEQUENCE OF CirbhGsmAlarmTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.1
cirbhGsmAlarmTableEntryEach entry represents the set of alarms that apply to GSM interface.
CirbhGsmAlarmTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.1.1
cirbhGsmAlarmConnectStateThe state of the connection for GSM interface.ro
CirbhConnectGsmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.1.1.1
cirbhGsmAlarmLocalStateThe local alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.1.1.2
cirbhGsmAlarmRemoteStateThe remote alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.1.1.3
cirbhGsmAlarmRedundancyStateThe redundancy state of the interfacero
CirbhRedundancyState
.1.3.6.1.4.1.9.9.483.1.2.1.2.1.1.4
cirbhUmtsConnectionTableThis table provides information associated with UMTS connection between BTS and BSC.
SEQUENCE OF CirbhUmtsConnectionTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.2
cirbhUmtsConnectionTableEntryEach Entry represents the set of alarms that apply to UMTS interfaces.
CirbhUmtsConnectionTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.2.1
cirbhUmtsConnectionStateThe state of the connection between the UMTS interfaces.ro
CirbhConnectUmtsState
.1.3.6.1.4.1.9.9.483.1.2.1.2.2.1.1
cirbhUmtsConnectionRedundStateThe redundancy state of the interface.ro
CirbhRedundancyState
.1.3.6.1.4.1.9.9.483.1.2.1.2.2.1.2
cirbhUmtsConnectionRootIfIndexThe root interface used to transport and receive UMTS traffic as follows. ATM: ATM0/0.0-aal5 layer -> ATM0/0-atm layer. IMA ATM0/IMA0.1-aal5 layer -> ATM0/IMA0ro
InterfaceIndexOrZero (IF-MIB)
.1.3.6.1.4.1.9.9.483.1.2.1.2.2.1.3
cirbhUmtsAlarmTableThis table provides information on alarm states for UMTS-ATM interfaces.
SEQUENCE OF CirbhUmtsAlarmTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.3
cirbhUmtsAlarmTableEntryEach entry provides information about the alarms for each ATM interface used to configure the shorthaul UMTS interface.
CirbhUmtsAlarmTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.2.3.1
cirbhUmtsAlarmRxLocalStateThe local receive alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.3.1.1
cirbhUmtsAlarmRxRemoteStateThe remote receive alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.3.1.2
cirbhUmtsAlarmTxLocalStateThe local transmit alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.3.1.3
cirbhUmtsAlarmTxRemoteStateThe remote transmit alarm state.ro
CirbhAlarmState
.1.3.6.1.4.1.9.9.483.1.2.1.2.3.1.4
cirbhShortHaulStats
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.1.3
cirbhStatsTableThis table provides measurements on bytes and packets sent or received on a per interface basis. It is important to note that this table shares the same index with the cirbhInfoTable table the ifIndex can be used to associate information from both tables.
SEQUENCE OF CirbhStatsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.1
cirbhStatsTableEntryThis entry provides measurements on shorthaul interfaces to allow compression efficency to be calculated.
CirbhStatsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1
cirbhStatsRcvdSamplesFor GSM-Abis interfaces, the count of samples received on interface. For UMTS interfaces, the number of packets received on interface.ro
Counter32
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.1
cirbhStatsSentSamplesFor GSM-Abis interfaces, the count of samples sent on interface. For UMTS interfaces, the number of packets sent on this interface.ro
Counter32
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.2
cirbhStatsRcvdBackHaulPacketsThe count of packets received from backhaul that contained data for this interface.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.3
cirbhStatsSentBackHaulPacketsThe count of packets transmitted on backhaul that contained data from this interface.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.4
cirbhStatsRcvdBackHaulBytesThe count of bytes received from backhaul that contained data for this interface.ro
Counter32 UNITS "bytes"
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.5
cirbhStatsSentBackHaulBytesThe count of bytes transmitted on backhaul that contained data from this interface.ro
Counter32 UNITS "bytes"
.1.3.6.1.4.1.9.9.483.1.2.1.3.1.1.6
cirbhErrorsTableThis table provides information on the errors that can be encountered during the compression and decompression of UMTS and GSM-Abis traffic. UMTS | GSM Linksdeprecated
SEQUENCE OF CirbhErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.2
cirbhErrorsTableEntryEach entry provides account of various types of errors encountered on GSM and UMTS interfaces.deprecated
CirbhErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1
cirbhErrorsBhPeerNotReadyDropsThe count of packets dropped on backhaul because peer was not ready.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.1
cirbhErrorsBhPeerNotActiveDropsThe count of packets dropped on backhaul because peer was reachable but not in active state.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.2
cirbhErrorsBhInvalidPacketsThe number of backhaul packets that were received and dropped because they contained invalid information.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.3
cirbhErrorsBhLostRcvdPacketsThe number of backhaul packets expected to be received but never arrived.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.4
cirbhErrorsBhLostSentPacketsThe number of backhaul packets sent but never were received by peer.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.5
cirbhErrorsBhMissedPacketsThe value of this object is the sum total of the values of the corresponding instances of the following objects: cirbhErrorsBhMissedLatePackets cirbhErrorsBhMissedLostPackets cirbhErrorsBhMissedNoMemPackets cirbhErrorsBhMissedResetPacketsrodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.6
cirbhErrorsBhMissedLatePacketsThe number of packets missed on backhaul because they arrived past the allowed time frame.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.7
cirbhErrorsBhMissedLostPacketsThe number of packets missed on backhaul because they were lost on backhaul.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.8
cirbhErrorsBhMissedNoMemPacketsThe number of packets missed on backhaul for lack of available memory to allocate packet.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.9
cirbhErrorsBhMissedResetPacketsThe number of packets missed on backhaul because the of a reset event.rodeprecated
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.10
cirbhErrorsDecompFailuresThe number of times information contained in packet could not be decompressed.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.11
cirbhErrorsCompFailuresThe number of times the information contained in the packet could not be compressed. This counter is incremented for all types of compression errors.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.12
cirbhErrorsCompNoPacketFailuresThe number of times compression failed because packet was unavailable.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.13
cirbhErrorsCompNoIntFailuresThe number of times compression failed because route to peer was not available.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.14
cirbhErrorsCompIntDownFailuresThe number of times compression failed because interface was down.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.15
cirbhErrorsCompEncapFailuresThe number of times compression failed because of encapsulation errors.rodeprecated
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.16
cirbhErrorsCompQosDropsThe number of times compression failed because of quality of service errors or traffic load.rodeprecated
Counter32 UNITS "drops"
.1.3.6.1.4.1.9.9.483.1.2.1.3.2.1.17
cirbhShortHaulHistoryTableThis table provides historical information on the amount of backhaul traffic contributed by each interface.obsolete
SEQUENCE OF CirbhShortHaulHistoryTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.3
cirbhShortHaulHistoryTableEntryEach entry represents the average traffic for last second. Each entry provides information on traffic rates for raw and compressed data.obsolete
CirbhShortHaulHistoryTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1
cirbhShortHaulHistoryAn index used to access history of cirbhShortHaulHistoryTable objects.obsolete
CirbhHistoryIndex
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.1
cirbhShortHaulRcvdRateThe rate of traffic received from this interface to be sent on backhaul prior to compression.roobsolete
CirbhRawInterfaceRate UNITS "bytes/second"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.2
cirbhShortHaulSentRateThe rate of traffic sent out from this interface after traffic was decompressed.roobsolete
CirbhRawInterfaceRate UNITS "bytes/second"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.3
cirbhShortHaulRcvdCompressRateThe rate of traffic received into this interface to be sent on backhaul after compression.roobsolete
CirbhCommpressInterfaceRate UNITS "bytes/second"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.4
cirbhShortHaulSentCompressRateThe rate of traffic received from backhaul and prior to decompression.roobsolete
CirbhCommpressInterfaceRate UNITS "bytes/second"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.5
cirbhShortHaulTimeStampTime when sample was collected.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.6
cirbhShortHaulRcvdUtilizationAmount of traffic that was receive from backhaul before decompression express as load on E1 or T1.roobsolete
CirbhShortHaulUtilization UNITS "percent of DS load"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.7
cirbhShortHaulSentUtilizationAmount of traffic that was send on after compression express as load on E1 or T1.roobsolete
CirbhShortHaulUtilization UNITS "percent of DS load"
.1.3.6.1.4.1.9.9.483.1.2.1.3.3.1.8
cirbhCongestionTableThis table provides information on congestion mechanism for shorthaul interfaces.
SEQUENCE OF CirbhCongestionTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.4
cirbhCongestionTableEntryEach entry represents single shorthaul interface.
CirbhCongestionTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1
cirbhCongestionEnabledThis object indicates congestion mechanisms have been enabled for shorthaul interface.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.1
cirbhCongestionDropsThis object provide the number packets or cells that were dropped due to congestion. When the cirbhInfoProtocol is 'gsmAbis' object indicates the number of packets dropped. When the cirbhInfoProtocol is 'umtsIub' object indicates the number of cells dropped.ro
Counter32
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.2
cirbhCongestionDroppedBytesThe number of bytes dropped due to congestion control mechanisms.ro
Counter32 UNITS "bytes"
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.3
cirbhCongestionEventsThe number of times congestion mechanism was engaged.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.4
cirbhCongestionActiveThis object indicates whether congestion mechanism is active.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.5
cirbhCongestionDurationThis object provides number of seconds interface was congested.ro
Counter32 UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.1.3.4.1.6
cirbhGsmErrorsTableThis table provides information on the errors that can be encountered during the compression and decompression of GSM-Abis traffic.
SEQUENCE OF CirbhGsmErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.5
cirbhGsmErrorsTableEntryEach entry represents single shorthaul interface.
CirbhGsmErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1
cirbhGsmErrorsPeerNotReadyDropsThe count of packets dropped on backhaul because peer was not ready.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.1
cirbhGsmErrorsPeerNotActiveDropsThe count of packets dropped on backhaul because peer was reachable but not in active state.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.2
cirbhGsmErrorsInvalidPacketsThe number of backhaul packets that were received and dropped because they contained invalid information.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.3
cirbhGsmErrorsLostRcvdPacketsThe number of backhaul packets expected to be received but never arrived.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.4
cirbhGsmErrorsLostSentPacketsThe number of backhaul packets sent but never were received by peer.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.5
cirbhGsmErrorsMissedPacketsThe value of this object is the sum total of the values of the corresponding instances of the following objects: cirbhGsmErrorsMissedLatePackets cirbhGsmErrorsMissedLostPackets cirbhGsmErrorsMissedNoMemPackets cirbhGsmErrorsMissedResetPacketsro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.6
cirbhGsmErrorsMissedLatePacketsThe number of packets missed on backhaul because they arrived past the allowed time frame.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.7
cirbhGsmErrorsMissedLostPacketsThe number of packets missed on backhaul because they were lost on backhaul.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.8
cirbhGsmErrorsMissedNoMemPacketsThe number of packets missed on backhaul for lack of available memory to allocate packet.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.9
cirbhGsmErrorsMissedResetPacketsThe number of packets missed on backhaul because the of a reset event.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.10
cirbhGsmErrorsDecompFailuresThe number of times information contained in packet could not be decompressed.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.11
cirbhGsmErrorsCompFailuresThe number of times the information contained in the packet could not be compressed.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.12
cirbhGsmErrorsCompNoPacketFailuresThe number of times compression failed because packet was unavailable.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.13
cirbhGsmErrorsCompNoIntFailuresThe number of times compression failed because route to peer was not available.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.14
cirbhGsmErrorsCompIntDownFailuresThe number of times compression failed because interface was down.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.15
cirbhGsmErrorsCompEncapFailuresThe number of times compression failed because of encapsulation errors.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.16
cirbhGsmErrorsCompQosDropsThe number of times compression failed because of quality of service errors or traffic load.ro
Counter32 UNITS "drops"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.17
cirbhGsmErrorsFastSendFailuresFast send failures.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.18
cirbhGsmErrorsTxPacketFailuresUnable to transmit GSM packet.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.19
cirbhGsmErrorsTxNoBuffersUnable to allocate buffer for transmission.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.20
cirbhGsmErrorsTxResetsTransmission interface resets.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.21
cirbhGsmErrorsOverrunsPacket was missed because backhaul jitter buffer was ran out of available space.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.22
cirbhGsmErrorsInterruptFailuresPacket was lost because of interrupt failure.ro
Counter32 UNITS "Failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.23
cirbhGsmErrorsLateArrivalsCount of GSM packets that arrived later than the allowed time.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.24
cirbhGsmErrorsEarlyArrivalsCount of GSM packets that arrived earlier than the allowed time.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.5.1.25
cirbhUmtsErrorsTableThis table provides information on the errors that can be encountered during the compression and decompression of UMTS-Iub traffic.
SEQUENCE OF CirbhUmtsErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.6
cirbhUmtsErrorsTableEntryEach entry represents single shorthaul interface.
CirbhUmtsErrorsTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1
cirbhUmtsErrorsPeerNotReadyDropsThe count of packets dropped on backhaul because peer was not ready.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.1
cirbhUmtsErrorsInvalidPacketsThe number of backhaul packets that were received and dropped because they contained invalid information.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.2
cirbhUmtsErrorsDecompFailuresThe number of times information contained in packet could not be decompressed.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.3
cirbhUmtsErrorsCompFailuresThe number of times the information contained int the packet could not be compressed.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.4
cirbhUmtsErrorsCompNoPacketFailuresThe number of times compression failed because packet was unavailable.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.5
cirbhUmtsErrorsCompNoIntFailuresThe number of times compression failed because route to peer was not available.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.6
cirbhUmtsErrorsCompIntDownFailuresThe number of times compression failed because interface was down.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.7
cirbhUmtsErrorsCompEncapFailuresThe number of times compression failed because of encapsulation errors.ro
Counter32 UNITS "failures"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.8
cirbhUmtsErrorsCompQosDropsThe number of times compression failed because of quality of service errors or traffic load.ro
Counter32 UNITS "drops"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.9
cirbhUmtsErrorsShorthaulPakFailuresUnable to allocate packet used to send data on shorthaul interface.ro
Counter32 UNITS "occurrences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.10
cirbhUmtsErrorsUmtsEncapFailuresThe UMTS encapsulate failures.ro
Counter32 UNITS "occurences"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.11
cirbhUmtsErrorsLocalPvcDropsPacket dropped because local PVC was unavailable.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.12
cirbhUmtsErrorsRemotePvcDropsPacket dropped because remote PVC was unavailable.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.13
cirbhUmtsErrorsBackhaulDropsPackets dropped on backhaul.ro
Counter32 UNITS "packets"
.1.3.6.1.4.1.9.9.483.1.2.1.3.6.1.14
cirbhShortHaulBulkTableThis table provides historical information on the amount of backhaul traffic contributed by each interface.
SEQUENCE OF CirbhShortHaulBulkTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.7
cirbhShortHaulBulkTableEntryEach entry represents the average traffic for last second. Each entry provides information on traffic rates for raw and compressed data.
CirbhShortHaulBulkTableEntry
.1.3.6.1.4.1.9.9.483.1.2.1.3.7.1
cirbhShortHaulBulkHistoryAn index used to access history of cirbhShortHaulBulkDataTable objects.
CirbhHistoryIndex
.1.3.6.1.4.1.9.9.483.1.2.1.3.7.1.1
cirbhShortHaulBulkTimeStampTime when sample was collected.ro
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.1.3.7.1.2
cirbhShortHaulBulkBaseUnitThe Base Unit is an integer used to provide a range of bytes rates provided in the cirbhShortHaulBulkUtil object. All values in the cirbhShortHaulBulkUtil object share the same base unit.ro
Unsigned32
.1.3.6.1.4.1.9.9.483.1.2.1.3.7.1.3
cirbhShortHaulBulkUtilThis object provides the amount of traffic transmitted in a particular shorthaul. The object contains 1 to 128 pairs. The length of the octet string can be used to calculate number of pairs. The information is in the following format were each rate is stored as single byte. [rx,tx] * 128 The approximated rate can be calculated by multiplying value from cirbhShortHaulBulkUtil times value in the cirbhShortHaulBulkBaseUnit.ro
OCTET STRING
.1.3.6.1.4.1.9.9.483.1.2.1.3.7.1.4
cirbhBackHaul
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.2
cirbhBackHaulInfo
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.2.1
cirbhBackHaulTableThis table provides information on backHaul links.obsolete
SEQUENCE OF CirbhBackHaulEntry
.1.3.6.1.4.1.9.9.483.1.2.2.1.1
cirbhBackHaulEntryEach entry represents a backhaul link between BSC and a particular BTS site.obsolete
CirbhBackHaulEntry
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1
cirbhBackHaulAdjectSerialNumThis object provides the serial number of the adjacent device supporting the backhaul connection. This object contains the same value as the corresponding entPhysicalSerialNum object. The type of object like chassis or module is provided by the cirbhBackHaulAdjectVendorType object.roobsolete
SnmpAdminString (SNMP-FRAMEWORK-MIB)
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.1
cirbhBackHaulAdjectVendorTypeThis object provides the vendor type of the adjacent device supporting backhaul connection. This object contains the same value as the corresponding entPhysicalVendorType object.roobsolete
AutonomousType (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.2
cirbhBackHaulRcvdUtilStateThe utilization state for traffic received on backhaul multilink. The following objects will be used to calculate link utilization state: cirbhBackHaulAcceptableThreshold cirbhBackHaulWarningThreshold cirbhBackHaulOverloadedThresholdroobsolete
CirbhBackHaulUtilizationState
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.3
cirbhBackHaulSentUtilStateThe utilization state for traffic transmitted on backhaul multilink. The following objects will be used to calculate link utilization state: cirbhBackHaulAcceptableThreshold cirbhBackHaulWarningThreshold cirbhBackHaulOverloadedThresholdroobsolete
CirbhBackHaulUtilizationState
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.4
cirbhBackHaulRcvdUtilThe average receive utilization of the link over the last second.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.5
cirbhBackHaulSentUtilThe average transmit utilization of the link over the last second.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.1.1.1.6
cirbhBackHaulShortHaulTableThis table lists the associations between shorthaul and backhaul interfaces.obsolete
SEQUENCE OF CirbhBackHaulShortHaulEntry
.1.3.6.1.4.1.9.9.483.1.2.2.1.2
cirbhBackHaulShortHaulEntryAn entry indicates a single association between a backhaul and shorthaul interface.obsolete
CirbhBackHaulShortHaulEntry
.1.3.6.1.4.1.9.9.483.1.2.2.1.2.1
cirbhBackHaulShortHaulBhIndexThis object indicates the backhaul interface.obsolete
InterfaceIndex (IF-MIB)
.1.3.6.1.4.1.9.9.483.1.2.2.1.2.1.1
cirbhBackHaulShortHaulShIndexThis object indicates the shorthaul interface.obsolete
InterfaceIndex (IF-MIB)
.1.3.6.1.4.1.9.9.483.1.2.2.1.2.1.2
cirbhBackHaulShortHaulTimestampThis object indicates the value of sysUpTime when the entry was created.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.2.1.2.1.3
cirbhBackHaulStats
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.2.2.2
cirbhBackHaulHistoryTableThis table provides historical information on traffic distribution on backhaul interface.obsolete
SEQUENCE OF CirbhBackHaulHistoryEntry
.1.3.6.1.4.1.9.9.483.1.2.2.2.1
cirbhBackHaulHistoryEntryEach entry provides information on the utilization of backhaul interface. The utilization is broken down by protocol and by direction. An entry is updated in this table every second.obsolete
CirbhBackHaulHistoryEntry
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1
cirbhBackHaulHistoryIndexAn index used to access history of cirbhBackHaulHistoryTable objects.obsolete
CirbhHistoryIndex
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.1
cirbhBackHaulHistoryRcvdUtilThe average receive utilization of link over the last second.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.2
cirbhBackHaulHistorySentUtilThe average transmit utilization of link over the last second.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.3
cirbhBackHaulHistoryRcvdAbisUtilThe average receive utilization of link over the last second that consisted of GSM-Abis traffic.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.4
cirbhBackHaulHistorySentAbisUtilThe average transmit utilization of link over the last second that consisted of GSM-Abis traffic.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.5
cirbhBackHaulHistoryRcvdUmtsUtilThe average receive utilization of link over the last second that consisted of UMTS traffic.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.6
cirbhBackHaulHistorySentUmtsUtilThe average transmit utilization of link over the last second that consisted of UMTS traffic.roobsolete
CirbhBackHaulUtilization UNITS "percent"
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.7
cirbhBackHaulHistoryTimeStampTime when sample was collected.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.2.2.1.1.8
cirbhBackHaulStatsTableThis table provides current information on the utilization of backhaul interface. One second load samples are collected and the corresponding entry is incremented. The provides a distribution of the traffic load. At the end of an interval the information is collected and used to populate entry in the cirbhBackHaulStatsHistoryTable. The interval is specified by the cirbhBackHaulStatsInterval object. The counters in this table increase until the interval ends at which time they are reset.obsolete
SEQUENCE OF CirbhBackHaulStatsEntry
.1.3.6.1.4.1.9.9.483.1.2.2.2.2
cirbhBackHaulStatsEntryEach entry contains the distribution of traffic in the current window specified by the cirbhBackHaulStatsInterval object.obsolete
CirbhBackHaulStatsEntry
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1
cirbhStatsDirectionThe direction of traffic on backhaul.obsolete
CirbhTrafficDirection
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.1
cirbhStatsTrafficTypeThe type of traffic.obsolete
CirbhTrafficType
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.2
cirbhStats000to009SecondsThe total numbers of seconds during which the backhaul link was utilized from 0 to 9 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.3
cirbhStats010to019SecondsThe total numbers of seconds during which the backhaul link was utilized from 10 to 19 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.4
cirbhStats020to029SecondsThe total numbers of seconds during which the backhaul link was utilized from 20 to 29 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.5
cirbhStats030to039SecondsThe total numbers of seconds during which the backhaul link was utilized from 30 to 39 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.6
cirbhStats040to049SecondsThe total numbers of seconds during which the backhaul link was utilized from 40 to 49 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.7
cirbhStats050to059SecondsThe total numbers of seconds during which the backhaul link was utilized from 50 to 59 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.8
cirbhStats060to069SecondsThe total numbers of seconds during which the backhaul link was utilized from 60 to 69 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.9
cirbhStats070to079SecondsThe total numbers of seconds during which the backhaul link was utilized from 70 to 79 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.10
cirbhStats080to089SecondsThe total numbers of seconds during which the backhaul link was utilized from 80 to 89 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.11
cirbhStats090to100SecondsThe total numbers of seconds during which the backhaul link was utilized from 90 to 100 percent.roobsolete
PerfCurrentCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.12
cirbhStatsTimeStampTime when sample was collected.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.13
cirbhStatsMaxUtilizationThe maximum utilization encountered within interval.roobsolete
CirbhBackHaulUtilization
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.14
cirbhStatsMaxTimeStampTime when cirbhStatsMaxUtilization was recorded.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.2.2.2.1.15
cirbhBackHaulStatsHistoryTableThis table provides historical information of distribution of load on backhaul interfaces.obsolete
SEQUENCE OF CirbhBackHaulStatsHistoryEntry
.1.3.6.1.4.1.9.9.483.1.2.12
cirbhBackHaulStatsHistoryEntryEach entry in this table is the data collected from the cirbhBackHaulStatsTable table.obsolete
CirbhBackHaulStatsHistoryEntry
.1.3.6.1.4.1.9.9.483.1.2.12.1
cirbhStatsHistoryIndexAn index used to access each 15 minute entry.obsolete
CirbhHistoryIndex
.1.3.6.1.4.1.9.9.483.1.2.12.1.1
cirbhStatsHistoryDirectionThe direction of traffic on backhaul.obsolete
CirbhTrafficDirection
.1.3.6.1.4.1.9.9.483.1.2.12.1.2
cirbhStatsHistoryTrafficTypeThe type of traffic in backhaul history table.obsolete
CirbhTrafficType
.1.3.6.1.4.1.9.9.483.1.2.12.1.3
cirbhStatsHistory000to009SecondsThe total numbers of seconds during which the backhaul link was utilized from 0 to 9 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.4
cirbhStatsHistory010to019SecondsThe total numbers of seconds during which the backhaul link was utilized from 10 to 19 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.5
cirbhStatsHistory020to029SecondsThe total numbers of seconds during which the backhaul link was utilized from 20 to 29 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.6
cirbhStatsHistory030to039SecondsThe total numbers of seconds during which the backhaul link was utilized from 30 to 39 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.7
cirbhStatsHistory040to049SecondsThe total numbers of seconds during which the backhaul link was utilized from 40 to 49 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.8
cirbhStatsHistory050to059SecondsThe total numbers of seconds during which the backhaul link was utilized from 50 to 59 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.9
cirbhStatsHistory060to069SecondsThe total numbers of seconds during which the backhaul link was utilized from 60 to 69 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.10
cirbhStatsHistory070to079SecondsThe total numbers of seconds during which the backhaul link was utilized from 70 to 79 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.11
cirbhStatsHistory080to089SecondsThe total numbers of seconds during which the backhaul link was utilized from 80 to 89 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.12
cirbhStatsHistory090to100SecondsThe total numbers of seconds during which the backhaul link was utilized from 90 to 100 percent.roobsolete
PerfIntervalCount UNITS "seconds"
.1.3.6.1.4.1.9.9.483.1.2.12.1.13
cirbhStatsHistoryTimeStampEnd time when sample was collected.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.12.1.14
cirbhStatsHistoryMaxUtilizationThe maximum utilization encountered within interval.roobsolete
CirbhBackHaulUtilization
.1.3.6.1.4.1.9.9.483.1.2.12.1.15
cirbhStatsHistoryMaxTimeStampTime when cirbhStatsHistoryMaxUtilization was recorded.roobsolete
TimeStamp (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.2.12.1.16
cirbhStatsHistoryAverageThe average utilization over the specified time period.roobsolete
CirbhBackHaulUtilization
.1.3.6.1.4.1.9.9.483.1.2.12.1.17
cirbhNotifEnables
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.1.3
cirbhGsmAlarmNotifEnabledThis object specifies whether the agent should generate the ciscoIpRanBackHaulGsmAlarm defined in this MIB module. 'true' Indicates that ciscoIpRanBackHaulGsmAlarm notification is to be generated. 'false' Indicates that ciscoIpRanBackHaulGsmAlarm notification generation is disabled.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.3.1
cirbhUmtsAlarmNotifEnabledThis object specifies whether the agent should generate the ciscoIpRanBackHaulUmtsAlarm defined in this MIB module. 'true' Indicates that ciscoIpRanBackHaulUmtsAlarm notification is to be generated. 'false' Indicates that ciscoIpRanBackHaulUmtsAlarm notification generation is disabled.rw
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.3.2
cirbhUtilNotifEnabledThis object specifies whether the agent should generate the ciscoIpRanBackHaulRcvdUtil or ciscoIpRanBackHaulSentUtil defined in this MIB module. 'true' Indicates that ciscoIpRanBackHaulRcvdUtil and ciscoIpRanBackHaulSentUtil notifications are to be generated. 'false' Indicates that ciscoIpRanBackHaulRcvdUtil and ciscoIpRanBackHaulSentUtil notifications generation is disabled.rwdeprecated
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.9.9.483.1.3.3
ciscoIpRanBackHaulMIBConform
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.2
ciscoIpRanBackHaulMIBCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.2.1
ciscoIpRanBackHaulMIBGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.483.2.2
CISCO-IP-RAN-BACKHAUL-MIB - SNMP MIB Reference | MIBs Explorer