CISCO-IF-LINK-CONFIG-MIB
AI MIB Summary
The CISCO-IF-LINK-CONFIG-MIB manages the configuration of Cisco bulk distribution modules to map high-bandwidth source interfaces (e.g., T3, OC-N) to lower-bandwidth target module interfaces, enabling traffic demultiplexing without requiring backplane cards on the target hardware. This module specifically monitors and controls the point-to-point bulk distribution bus connections that allow source line cards to function as target module interfaces.
The MIB module for configuration of bulk distribution (de-multiplexing of traffic from higher-bandwidth to lower-bandwidth interfaces).
Terminology :
bulk-distribution : The bulk distribution is the feature by which a line/interface on one module can replace the line for the other.
bulk-distribution module : The module which links its interfaces to the target module.
target module : A module that gets incoming traffic from a bulk distribution module rather than from a back card.
The Module which supports bulk distribution, converts traffic from its lines (may be T3, OC-N) to lines on the target module (may be T3, T1 etc). The bulk distribution is achieved by having a point-to-point connection (bulk-distribution bus) between the bulk-distribution module and the target module. The benefit of bulk distribution is that the target module need not have the back cards. The lines/interfaces from bulk-distribution module will be used as lines for the target module.
An example is given here on linking interfaces.
|| | | | | | | | | | | | | |-| | | Ta|rget Module | | | | |
- -
| | | | | | | | | | | | | | | | | T1 | | T1 | |T1 | | Bulk | |card | |card | |card | | Distribution | | | | | | | | | | | | | | | | Module | | | | | | | | | | | | | | | | (T3 card) | | | | | | | | |
- -
Main OID:
ciscoIfLinkConfigMIB.1.3.6.1.4.1.9.9.175
12
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
12 total| Object Name |
|---|
ciscoIfLinkConfigMIBThe MIB module for configuration of bulk distribution
(de-multiplexing of traffic from higher-bandwidth to
lower-bandwidth interfaces).
Terminology :
bulk-distribution : The bulk distribution is the
feature by which a line/interface
on one module can replace the line
for the other.
bulk-distribution module : The module which links its
interfaces to the target module.
target module : A module that gets incoming traffic
from a bulk distribution module
rather than from a back card.
The Module which supports bulk distribution, converts
traffic from its lines (may be T3, OC-N) to lines on
the target module (may be
T3, T1 etc). The bulk distribution is achieved by having a
point-to-point connection (bulk-distribution bus) between the
bulk-distribution module and the target module. The benefit
of bulk distribution is that the target module need not have
the back cards. The lines/interfaces from bulk-distribution
module will be used as lines for the target module.
An example is given here on linking interfaces.
||
| |
| |
| | | | | |
| | |-| | |
Ta|rget Module | | | | |
- -
| | | | | | | |
| | | | | | | |
| T1 | | T1 | |T1 | | Bulk |
|card | |card | |card | | Distribution |
| | | | | | | |
| | | | | | | Module |
| | | | | | | |
| | | | | | | (T3 card) |
| | | | | | | |
- - MODULE-IDENTITY .1.3.6.1.4.1.9.9.175 |
cilConfigMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.175.1 |
cilConfig OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.175.1.1 |
cilConfTableThe interface link configuration table. SEQUENCE OF CilConfEntry .1.3.6.1.4.1.9.9.175.1.1.1 |
cilConfEntryAn entry in the cilConfTable. This entry is used for
linking an interface identified by cilSourceInterface
to an interface identified by cilTaregetModuleInterface.
The entries are created and deleted using the
cilRowStatus object. An interface on the bulk-distribution
module cannot be linked to multiple interfaces in the
target module. CilConfEntry .1.3.6.1.4.1.9.9.175.1.1.1.1 |
cilSourceInterfaceAn interface of the bulk-distribution module (Source) which
will be linked with the interface of the target module. It
represents an entry in the ifTable. InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.175.1.1.1.1.1 |
cilTargetModuleInterfaceLocation of the managed entity on the target module.
Following is the supported format for this object and
all the values must be present.
shelf=<value>, slot=<value>, subSlot=<value> port =<value>.
The zero length value for this object is not supported.rw CiscoLocationSpecifier (CISCO-TC) .1.3.6.1.4.1.9.9.175.1.1.1.1.2 |
cilRowStatusThis object is used to create a new row or modify or delete
an existing row in the table. The cilTargetModuleFramingType
need not be specified to create a row. If cilTargetModuleFramingType
is not specified, a default value will be assumed as described in the
description of cilTargetModuleFramingType.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.9.175.1.1.1.1.3 |
cilTargetModuleFramingTypeThis object identifies the framing type of the target interface.
notApplicable(1) can not be set.
dsx1ESF Extended SuperFrame DS1 (T1.107)
dsx1D4 AT&T D4 format DS1 (T1.107)
Default value is dsx1ESF(3) if cilTargetModuleInterface is a T1 interface
and sonet/sdh byte-synchronous mapping is used on the cilSourceInterface.
Otherwise, the default value is notApplicable(1).rw Enumeration .1.3.6.1.4.1.9.9.175.1.1.1.1.4 |
cilConfigMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.175.3 |
cilConfigMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.175.3.1 |
cilConfigMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.175.3.2 |