CISCO-IETF-VDSL-LINE-MIB
AI MIB Summary
The CISCO-IETF-VDSL-LINE-MIB enables monitoring and control of VDSL modem pairs by exposing physical layer performance metrics—including SNR margins, attenuation, and error counters (ES, LOS, LOF)—across physical, Fast, and Interleaved channel interfaces within the ifTable. It facilitates the management of VDSL line states and protocol parameters without requiring inter-agent communication, utilizing specific naming conventions (Vtur, Vtuc, Curr, Prev) to track transient and historical line statistics.
The MIB module defining objects for the management of a pair of VDSL modems at each end of the VDSL line. Each VDSL line has an entry in an ifTable.
An agent may reside at either end of the VDSL line however the MIB is designed to require no management communication between them beyond that inherent in the low-level VDSL line protocol. The agent may monitor and control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus a VDSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to vdsl(97), fast(125), and interleaved(124), respectively. The ifStackTable is used to represent the relationship between the entries.
Naming Conventions: Vtuc Vtur Vtu Curr Prev Atn ES LCS Lof Lol Los Lpr xyzs (e.g., xyz=Lof, Los, Lpr) Max Mgn Min Psd Snr Tx Blks
Main OID:
ciscoIetfVdslMIB.1.3.6.1.4.1.9.10.87
87
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
87 total| Object Name |
|---|
ciscoIetfVdslMIBThe MIB module defining objects for the management of a pair of
VDSL modems at each end of the VDSL line. Each VDSL line has
an entry in an ifTable.
An agent may reside at either end of the VDSL line however the
MIB is designed to require no management communication between
them beyond that inherent in the low-level VDSL line protocol.
The agent may monitor and control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc
Vtur
Vtu
Curr
Prev
Atn
ES
LCS
Lof
Lol
Los
Lpr
xyzs
(e.g., xyz=Lof, Los, Lpr)
Max
Mgn
Min
Psd
Snr
Tx
Blks MODULE-IDENTITY .1.3.6.1.4.1.9.10.87 |
cvdslLineMib OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1 |
cvdslNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1.0 |
cvdslInitFailureNotificationVtu initialization failed. See cvdslCurrStatus for
potential reasons. NOTIFICATION-TYPE .1.3.6.1.4.1.9.10.87.1.0.1 |
cvdslMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1.1 |
cvdslLineTableThis table includes common attributes describing
both ends of the line. It is required for all VDSL
physical interfaces. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97). SEQUENCE OF CvdslLineEntry .1.3.6.1.4.1.9.10.87.1.1.1 |
cvdslLineEntryAn entry in the cvdslLineTable. CvdslLineEntry .1.3.6.1.4.1.9.10.87.1.1.1.1 |
cvdslLineCodingSpecifies the VDSL coding type used on this line.ro CVdslLineCodingType .1.3.6.1.4.1.9.10.87.1.1.1.1.1 |
cvdslLineTypeDefines the type of VDSL physical line
entity that exists, by defining whether and how
the line is channelized. If the line is channelized,
the value will be other than noChannel(1). This
object defines which channel type(s) are supported.
In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s).ro Enumeration .1.3.6.1.4.1.9.10.87.1.1.1.1.2 |
cvdslLineConfProfileThe value of this object identifies the rows
in the VDSL Line Configuration Profile Table,
( cvdslLineConfProfileTable ), which apply for this
VDSL line, and channels if applicable.rw Integer32 .1.3.6.1.4.1.9.10.87.1.1.1.1.3 |
cvdslLineAlarmConfProfileThe value of this object identifies the rows in the VDSL
Line Alarm Configuration Profile Table,
( cvdslLineAlarmConfProfileTable ), which apply to this
VDSL line, and channels if applicable.rw Integer32 .1.3.6.1.4.1.9.10.87.1.1.1.1.4 |
cvdslPhysTableThis table provides one row for each Vtu. Each row
contains the Physical Layer Parameters table for that
Vtu. VDSL physical interfaces are those ifEntries where
ifType is equal to vdsl(97). SEQUENCE OF CvdslPhysEntry .1.3.6.1.4.1.9.10.87.1.1.2 |
cvdslPhysEntryAn entry in the cvdslPhysTable. CvdslPhysEntry .1.3.6.1.4.1.9.10.87.1.1.2.1 |
cvdslPhysSideIdentifies whether the modem is the Vtuc or Vtur. CVdslLineEntity .1.3.6.1.4.1.9.10.87.1.1.2.1.1 |
cvdslInvSerialNumberThe vendor specific string that identifies the
vendor equipment.ro SnmpAdminString .1.3.6.1.4.1.9.10.87.1.1.2.1.2 |
cvdslInvVendorIDThe vendor ID code is a copy of the binary vendor
identification field defined by the PHY[10] and
expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.9.10.87.1.1.2.1.3 |
cvdslInvVersionNumberThe vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters.ro SnmpAdminString .1.3.6.1.4.1.9.10.87.1.1.2.1.4 |
cvdslCurrSnrMgnNoise Margin as seen by this Vtu with respect to its
received signal in tenth dB.ro INTEGER(-640..640) UNITS "tenth dB" .1.3.6.1.4.1.9.10.87.1.1.2.1.5 |
cvdslCurrAtnMeasured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu.ro Gauge32 .1.3.6.1.4.1.9.10.87.1.1.2.1.6 |
cvdslCurrStatusIndicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming Vtu failure due to not receiving
valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to
link with peer Vtu.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to support
requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus.ro Bits .1.3.6.1.4.1.9.10.87.1.1.2.1.7 |
cvdslCurrOutputPwrMeasured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence.ro INTEGER (-310..310) UNITS "tenth dBm" .1.3.6.1.4.1.9.10.87.1.1.2.1.8 |
cvdslCurrAttainableRateIndicates the maximum currently attainable data rate
by the Vtu. This value will be equal or greater than
the current line rate.ro Gauge32 UNITS "bps" .1.3.6.1.4.1.9.10.87.1.1.2.1.9 |
cvdslChanTableThis table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125). SEQUENCE OF CvdslChanEntry .1.3.6.1.4.1.9.10.87.1.1.3 |
cvdslChanEntryAn entry in the cvdslChanTable. CvdslChanEntry .1.3.6.1.4.1.9.10.87.1.1.3.1 |
cvdslChanInterleaveDelayInterleave Delay for this channel.
Interleave delay applies only to the interleave
(slow) channel and defines the mapping (relative
spacing) between subsequent input bytes at the
interleaver input and their placement in the bit
stream at the interleaver output. Larger numbers
provide greater separation between consecutive
input bytes in the output bit stream allowing for
improved impulse noise immunity at the expense of
payload latency.
In the case where the ifType is fast(125), the
object is not instantiated.ro Gauge32 UNITS "milli-seconds" .1.3.6.1.4.1.9.10.87.1.1.3.1.1 |
cvdslChanCrcBlockLengthIndicates the length of the channel data-block
on which the CRC operates.ro Gauge32 UNITS "byte" .1.3.6.1.4.1.9.10.87.1.1.3.1.2 |
cvdslLineConfProfileTableThis table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line. SEQUENCE OF CvdslLineConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.8 |
cvdslLineConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of a VDSL modem. A
default profile with an index of 1 will always exist
and its parameters will be set to vendor specific
values, unless otherwise specified in this document. CvdslLineConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.8.1 |
cvdslLineConfProfileIndexThis object is used by the line configuration table
in order to identify a row in that table. The system
will always provide a default profile whose value is 1. Integer32 .1.3.6.1.4.1.9.10.87.1.1.8.1.1 |
cvdslLineConfProfileNameThe name for this profile as specified by a user.rw SnmpAdminString .1.3.6.1.4.1.9.10.87.1.1.8.1.2 |
cvdslLineConfTargetSnrMgnConfigured Target Signal/Noise Margin. This is the
Noise Margin the modem must achieve with a BER of 10-7
or better to successfully complete initialization.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.8.1.3 |
cvdslLineConfTxSpeedTransmit speed for this modem. The corresponding modem
on the other end of the VDSL line will have an equal
cvdslLineConfRxSpeed value.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.8.1.4 |
cvdslLineConfRxSpeedReceive speed for this modem. The corresponding modem
on the other end of the VDSL line will have an equal
cvdslLineConfTxSpeed value.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.8.1.5 |
cvdslLineConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.
The DEFVAL profile cannot be deleted.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.8.1.6 |
cvdslLineMCMConfProfileTableThis table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.9 |
cvdslLineMCMConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of a multiple carrier
modulation VDSL modem. A default profile with an
index of 1 will always exist and its parameters will
be set to vendor specific values, unless otherwise
specified in this document. CvdslLineMCMConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.9.1 |
cvdslMCMConfProfileTxWindowLengthSpecifies the length of the transmit window, counted
in samples at the sampling rate corresponding to the
negotiated value of N.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.9.1.1 |
cvdslMCMConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.9.1.2 |
cvdslLineMCMConfProfileTxBandTableThis table contains transmit band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileTxBandEntry .1.3.6.1.4.1.9.10.87.1.1.10 |
cvdslLineMCMConfProfileTxBandEntryEach entry consists of a transmit band descriptor, which
is defined by a start and a stop tone index.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineMCMConfProfileTxBandEntry .1.3.6.1.4.1.9.10.87.1.1.10.1 |
cvdslMCMConfProfileTxBandNumberThe index for this band descriptor entry. INTEGER .1.3.6.1.4.1.9.10.87.1.1.10.1.1 |
cvdslMCMConfProfileTxBandStartStart tone index for this band.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.10.1.2 |
cvdslMCMConfProfileTxBandStopStop tone index for this band.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.10.1.3 |
cvdslMCMConfProfileTxBandRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.10.1.4 |
cvdslLineMCMConfProfileRxBandTableThis table contains receive band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileRxBandEntry .1.3.6.1.4.1.9.10.87.1.1.11 |
cvdslLineMCMConfProfileRxBandEntryEach entry consists of a transmit band descriptor, which
defines the start and stop bands and the power spectral
density (PSD) for that band.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineMCMConfProfileRxBandEntry .1.3.6.1.4.1.9.10.87.1.1.11.1 |
cvdslMCMConfProfileRxBandNumberThe index for this band descriptor entry. INTEGER .1.3.6.1.4.1.9.10.87.1.1.11.1.1 |
cvdslMCMConfProfileRxBandStartStart tone index for this band.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.11.1.2 |
cvdslMCMConfProfileRxBandStopStop tone index for this band.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.11.1.3 |
cvdslMCMConfProfileRxBandRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.11.1.4 |
cvdslLineMCMConfProfileTxPSDTableThis table contains transmit PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL line. These
entries are defined by a manager and can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileTxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.12 |
cvdslLineMCMConfProfileTxPSDEntryEach entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineMCMConfProfileTxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.12.1 |
cvdslMCMConfProfileTxPSDNumberThe index for this mask descriptor entry. INTEGER .1.3.6.1.4.1.9.10.87.1.1.12.1.1 |
cvdslMCMConfProfileTxPSDToneThe tone index for which the PSD is being specified.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.12.1.2 |
cvdslMCMConfProfileTxPSDPSDPower Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.12.1.3 |
cvdslMCMConfProfileTxPSDRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.12.1.4 |
cvdslLineMCMConfProfileMaxTxPSDTableThis table contains transmit maximum PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileMaxTxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.13 |
cvdslLineMCMConfProfileMaxTxPSDEntryEach entry consists of a transmit PSD mask descriptor,
which defines the maximum power spectral density (PSD)
for a tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineMCMConfProfileMaxTxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.13.1 |
cvdslMCMConfProfileMaxTxPSDNumberThe index for this band descriptor entry. INTEGER .1.3.6.1.4.1.9.10.87.1.1.13.1.1 |
cvdslMCMConfProfileMaxTxPSDToneThe tone index for which the PSD is being specified.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.13.1.2 |
cvdslMCMConfProfileMaxTxPSDPSDPower Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.13.1.3 |
cvdslMCMConfProfileMaxTxPSDRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.13.1.4 |
cvdslLineMCMConfProfileMaxRxPSDTableThis table contains maximum receive PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line. SEQUENCE OF CvdslLineMCMConfProfileMaxRxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.14 |
cvdslLineMCMConfProfileMaxRxPSDEntryEach entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a
tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineMCMConfProfileMaxRxPSDEntry .1.3.6.1.4.1.9.10.87.1.1.14.1 |
cvdslMCMConfProfileMaxRxPSDNumberThe index for this band descriptor entry. INTEGER .1.3.6.1.4.1.9.10.87.1.1.14.1.1 |
cvdslMCMConfProfileMaxRxPSDToneThe tone index for which the PSD is being specified.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.14.1.2 |
cvdslMCMConfProfileMaxRxPSDPSDPower Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.14.1.3 |
cvdslMCMConfProfileMaxRxPSDRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.14.1.4 |
cvdslLineSCMConfProfileTableThis table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line. SEQUENCE OF CvdslLineSCMConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.15 |
cvdslLineSCMConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of a single carrier
modulation VDSL modem.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineSCMConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.15.1 |
cvdslSCMConfProfileInterleaveDepthSpecifies the interleaving depth.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.1 |
cvdslSCMConfProfileFastCodewordSizeSpecifies the length in octets of the fast codeword.
A value of 0 indicates that the single latency transport
class is to be utilized.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.2 |
cvdslSCMConfProfileTransmitPSDMaskThe transmit power spectral density mask code.rw Bits .1.3.6.1.4.1.9.10.87.1.1.15.1.3 |
cvdslSCMConfProfileTransmitPSDLevelThe transmit power spectral density for the VDSL modem.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.4 |
cvdslSCMConfProfileSymbolRateProfileThe symbol rate profile calculated as S = SR/BSR, where
SR is the required symbol rate in kbaud, BSR = 67.5.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.5 |
cvdslSCMConfProfileConstellationSizeSpecifies the constellation size.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.6 |
cvdslSCMConfProfileCenterFrequencySpecifies the center frequency profile K.rw INTEGER .1.3.6.1.4.1.9.10.87.1.1.15.1.7 |
cvdslSCMConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.15.1.8 |
cvdslLineAlarmConfProfileTableThis table contains information on the VDSL line alarm
configuration. One entry in this table reflects a profile
defined by a manager which can be used to configure the
VDSL line alarm thresholds. SEQUENCE OF CvdslLineAlarmConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.16 |
cvdslLineAlarmConfProfileEntryEach entry consists of a list of parameters that
represents the configuration of a VDSL line alarm
profile.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document. CvdslLineAlarmConfProfileEntry .1.3.6.1.4.1.9.10.87.1.1.16.1 |
cvdslLineAlarmConfProfileIndexThis object is used by the line alarm configuration table
in order to identify a row in that table. The system will
always provide a default profile whose index is 1. Integer32 .1.3.6.1.4.1.9.10.87.1.1.16.1.1 |
cvdslLineAlarmConfProfileNameThe name for this profile as specified by a user.rw SnmpAdminString .1.3.6.1.4.1.9.10.87.1.1.16.1.2 |
cvdslInitFailureNotificationEnableThis object specifies if a cvdslInitFailureNotification
notification will be generated if an initialization
failure occurs.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.16.1.3 |
cvdslLineAlarmConfProfileRowStatusThis object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.9.10.87.1.1.16.1.4 |
cvdslConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1.3 |
cvdslGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1.3.1 |
cvdslCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.87.1.3.2 |