CISCO-FSPF-MIB
AI MIB Summary
The CISCO-FSPF-MIB enables monitoring and management of the Fabric Shortest Path First routing protocol on Cisco Fibre Channel switches, tracking critical metrics such as neighbor adjacencies, SPF calculation events, and interface state transitions within the SAN fabric.
Fabric Shortest Path First (FSPF) MIB.
83
Objects
Active
Status
9
Dependencies
Imported Objects
Objects
83 total| Object Name |
|---|
ciscoFspfMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287 |
RFC1155-SMI Unknown .1.3.6.1.4.1.9.9.287 |
fspfConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.1 |
fspfTableThis table allows the users to configure and monitor the
Fabric Shortest Path First (FSPF) parameters on all the VSANs
configured on the local switch.
Entries in this tables are automatically created when VSANs
are either created or activated (if an entry for that VSAN is
not already existing).
An entry is deleted automatically from this table if either:
- the corresponding VSAN is deleted.
or
- the corresponding VSAN is suspended and the values of
all writable objects in that entry have default values.
An entry can be created through the use of fspfRowStatus
only as a re-creation of that entry after it was deleted
because the corresponding VSAN was suspended, and while
the VSAN continues to exist.
So an entry in this table exists when one or both of these
conditions holds:
- one or more configuration parameters have non-default
values for a VSAN which is suspended, and/or
- the VSAN is active.
This has a number of consequences:
- an entry exists for a suspended VSAN whenever that VSAN
has non-default parameters.
- an entry cannot be created (via fspfRowStatus) for a
VSAN with default parameters; instead, the agent
creates/deletes an entry for a VSAN with default
parameters according to whether the VSAN is active or
suspended.
- an entry can not be created via fspfIfRowStatus unless
non-default parameter values are (simultaneously)
configured for a VSAN which is suspended;
- deleting an entry via RowStatus when either the VSAN is
suspended and configured with non-default values or the
VSAN is active, is equivalent to resetting its parameters
to their default values.
If the VSAN is suspended and was configured with default-
values, then the entry would be deleted. SEQUENCE OF FspfEntry .1.3.6.1.4.1.9.9.287.1.1 |
fspfEntryThis entry contains the FSPF parameters on this VSAN. FspfEntry .1.3.6.1.4.1.9.9.287.1.1.1 |
fspfRegionIdThe autonomous region of the local switch on this VSAN.rw FspfRegionId -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.1.1.1.1 |
fspfDomainIdThe Domain Id of the local switch on this VSAN.ro DomainId -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.1.1.1.2 |
fspfSpfDelayThe time between when FSPF receives topology updates and
when it starts the Shortest Path First (SPF) computation
on this VSAN. The smaller value means that routing will
react to the changes faster but the CPU usage is greater.ro TimeIntervalSec -- Rsyntax Gauge -- Units -- Seconds .1.3.6.1.4.1.9.9.287.1.1.1.3 |
fspfSpfHoldTimeThe minimum time between two consecutive SPF computations
on this VSAN. The smaller value means that routing will
react to the changes faster but the CPU usage is greater.rw CiscoMilliSeconds .1.3.6.1.4.1.9.9.287.1.1.1.4 |
fspfMinLsArrivalThe minimum time after accepting a Link State Record
(LSR) on this VSAN before accepting another update of
the same LSR on the same VSAN.
An LSR update that is not accepted because of this time
interval is discarded.rw CiscoMilliSeconds .1.3.6.1.4.1.9.9.287.1.1.1.5 |
fspfMinLsIntervalThe minimum time after this switch sends an LSR on this
VSAN before it will send another update of the same LSR on
the same VSAN.rw CiscoMilliSeconds .1.3.6.1.4.1.9.9.287.1.1.1.6 |
fspfLsRefreshTimeThe interval between transmission of refresh LSRs on this
VSAN.ro TimeIntervalMin -- Rsyntax Gauge -- Units -- Minutes .1.3.6.1.4.1.9.9.287.1.1.1.7 |
fspfMaxAgeThe maximum age an LSR will be retained in the FSPF
database on this VSAN. It is removed from the database
after MaxAge is reached.ro TimeIntervalMin -- Rsyntax Gauge -- Units -- Minutes .1.3.6.1.4.1.9.9.287.1.1.1.8 |
fspfMaxAgeCountThe number of times any LSR reached fspfMaxAge in this
VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.9 |
fspfSpfComputationsThe number of times the SPF computation has been done on
this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.10 |
fspfChecksumErrorsThe number of FSPF checksum errors occurred on this on
this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.11 |
fspfLsuRxPktsTotal number of Link State Update (LSU) packets received
on all the interfaces on this VSAN since the creation of
the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.12 |
fspfLsaRxPktsTotal number of Link State Acknowledgement (LSA) packets
received on all the interfaces on this VSAN since the
creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.13 |
fspfLsuTxPktsTotal number of Link State Update (LSU) packets
transmitted on all the interfaces on this VSAN since the
creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.14 |
fspfLsaTxPktsTotal number of Link State Acknowledgement (LSA) packets
transmitted on all the interfaces on this VSAN since the
creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.15 |
fspfHelloTxPktsTotal number of HELLO packets transmitted on all
interfaces on this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.16 |
fspfHelloRxPktsTotal number of HELLO packets received on all the
interfaces on this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.17 |
fspfRetransmittedLsuTxPktsTotal number of LSU packets retransmitted on all the
interfaces on this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.18 |
fspfErrorRxPktsNumber of invalid FSPF control packets received on all
the interface on this VSAN since the creation of the
entry.ro Counter .1.3.6.1.4.1.9.9.287.1.1.1.19 |
fspfLsrsThe number of current entries for this VSAN in the
fspfLsrTable.ro Gauge .1.3.6.1.4.1.9.9.287.1.1.1.20 |
fspfCreateTimeThe value of sysUpTime when this entry was last created.ro LastCreationTime -- Rsyntax TimeTicks .1.3.6.1.4.1.9.9.287.1.1.1.21 |
fspfAdminStatusThe desired state of FSPF on this VSAN. If value of
this object is set to up (1) , then FSPF is enabled on
this VSAN. If set to down (2) , then FSPF is disabled on
this VSAN.rw Enumeration .1.3.6.1.4.1.9.9.287.1.1.1.22 |
fspfOperStatusState of FSPF on this VSAN. If 'fspfAdminStatus' is
down (2) then the 'fspfOperStatus' should be down (2).
If 'fspfAdminStatus' is changed to up (1) then
'fspfOperStatus' should change to up (1) as and when FSPF
is active on this VSAN.ro Enumeration .1.3.6.1.4.1.9.9.287.1.1.1.23 |
fspfSetToDefaultSetting this value to 'default' changes the value of each
and every every write-able object in this row to its default
value.
If all the configuration parameters have their default values
and if the VSAN is suspended, then the row is deleted
automatically.
No action is taken if this object is set to 'noOp'.
The value of the object when read is always 'noOp'.rw Enumeration .1.3.6.1.4.1.9.9.287.1.1.1.24 |
fspfRowStatusThe status of conceptual row on this VSAN.
This object can be used to create an entry only if
the corresponding VSAN is suspended. If the VSAN
is either not-existent or active, a create will fail.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.287.1.1.1.25 |
fspfIfTableThis table allows the users to configure and monitor the
Fabric Shortest Path First (FSPF) parameters on all
interfaces on all the VSANs configured on the local switch.
An entry is automatically created in this table if there
is an entry in the fspfTable for a VSAN when an E_port
comes up on that VSAN.
An entry is automatically deleted from this table if
either :
a) the interface transitions to being a down interface which
is configured with default values and which is either
down or a non-E_port,
or
b) the fspfTable entry for the corresponding VSAN is
deleted.
Entries in this table can be created via fspfIfRowStatus
only as the means to specify non-default parameter values
for an interface at a time when that interface is either down
or is a non-E_port.
So an entry in this table exists when one or both of these
conditions holds:
- one or more configuration parameters have non-default
values for an interface which is either down or
a non-E_port and corresponding VSAN has an entry
in the fspfTable, and/or
- the interface is an E_port and it is up.
This has a number of consequences:
- an entry exists for a non-E_port or an E_port which is down
whenever that interface has non-default parameters and the
corresponding VSAN has an entry in the fspfTable;
- an entry cannot be created (via fspfIfRowStatus) for an
interface with default parameters; instead, the agent
creates/deletes an entry for an interface with default
parameters according to whether the E_port is up or
down.
- an entry can not be created via fspfIfRowStatus unless
non-default parameter values are (simultaneously)
configured for an interface which is a non-E_port or a
down interface, and the corresponding VSAN has an entry in
the fspfTable.
- deleting an entry via RowStatus when either the interface
is down and configured with non-default values or the
interface is up, is equivalent to resetting its parameters
to their default values.
If the interface is down and was configured with default-
values, then the entry would be deleted. SEQUENCE OF FspfIfEntry .1.3.6.1.4.1.9.9.287.1.2 |
fspfIfEntryAn entry containing information for an FSPF interface
on this VSAN. The entry is created when a FSPF is enabled
on this VSAN by creating an entry in the fspfTable on this
VSAN. 'vsanIndex' specifies a particular VSAN and
'ifIndex' specifies the particular interface for an
entry. FspfIfEntry .1.3.6.1.4.1.9.9.287.1.2.1 |
fspfIfCostThe administrative cost of sending a frame on this
interface on this VSAN. The value 0 means that the cost
has not been configured. Once the value has been
configured, the value can not again be zero; so, obviously
the value can not be set to 0.
If the value of this object is 0 and the corresponding
interface is up, the agent sets this object to a value
calculated using the 'ifSpeed' of the interface. Otherwise,
the value of this object is used as the cost.
Note that following formula is used to calculate the link
cost.
Link Cost = { fspfIfCost if fspfIfCost > 0
{(1.0625e12 / Baud Rate) if fspfIfCost == 0
where Baud Rate is the ifSpeed of the interface.rw Gauge .1.3.6.1.4.1.9.9.287.1.2.1.1 |
fspfIfHelloIntervalInterval between the periodic HELLO messages sent on this
interface on this VSAN to verify the link health. Note
that this value must be same on both the interfaces on
each end of the link on this VSAN.rw TimeIntervalSec .1.3.6.1.4.1.9.9.287.1.2.1.2 |
fspfIfDeadIntervalMaximum time for which no HELLO messages can be received
on this interface on this VSAN. After this time, the
interface is assumed to be broken and removed from the
database. Note that this value must be greater than the
HELLO interval specified on this interface on this VSAN.rw TimeIntervalSec .1.3.6.1.4.1.9.9.287.1.2.1.3 |
fspfIfRetransmitIntervalTime after which an unacknowledged link update is
retransmitted on this interface on this VSAN.rw TimeIntervalSec .1.3.6.1.4.1.9.9.287.1.2.1.4 |
fspfIfLsuRxPktsNumber of Link State Update (LSU) packets received on
this interface on this VSAN since the creation of the
entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.5 |
fspfIfLsaRxPktsNumber of Link State Acknowledgement (LSA) packets
received on this interface on this VSAN since the
creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.6 |
fspfIfLsuTxPktsNumber of Link State Update (LSU) packets transmitted
on this interface on this VSAN since the creation of the
entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.7 |
fspfIfLsaTxPktsNumber of Link State Acknowledgement (LSA) packets
transmitted on this interface on this VSAN since the
creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.8 |
fspfIfHelloTxPktsNumber of HELLO packets transmitted on this interface on
this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.9 |
fspfIfHelloRxPktsNumber of HELLO packets received on this interface on
this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.10 |
fspfIfRetransmittedLsuTxPktsNumber of LSU packets retransmitted on this interface on
this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.11 |
fspfIfErrorRxPktsNumber of invalid FSPF control packets received on this
interface on this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.12 |
fspfIfInactivityExpirationsNumber of times the inactivity timer has expired on this
interface on this VSAN since the creation of the entry.ro Counter .1.3.6.1.4.1.9.9.287.1.2.1.13 |
fspfIfNbrStateThe state of FSPF's 'neighbor state machine', which is
the operational state of the interaction with the
neighbor's interface which is connected to this interface.
If the 'fspfIfAdminStatus' is down(2), then this object
should be down (1). If the 'fspfIfAdminStatus' is up (2)
then this object should be take any of the possible values
depending on the state of FSPF's 'neighbor state machine'
on this interface on this VSAN.ro FspfInterfaceState -- Rsyntax INTEGER { -- down(1), -- init(2), -- dbExchange(3), -- dbAckwait(4), -- dbWait(5), -- full(6) -- } .1.3.6.1.4.1.9.9.287.1.2.1.14 |
fspfIfNbrDomainIdThe Domain Id of the neighbor on this VSAN.ro DomainIdOrZero -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.1.2.1.15 |
fspfIfNbrPortIndexThe index, as known by the neighbor, of the neighbor's
interface which is connected to this interface on this
VSAN.ro Gauge .1.3.6.1.4.1.9.9.287.1.2.1.16 |
fspfIfAdminStatusThe desired state of FSPF on this interface on this VSAN.
If value of this object is set to 'up', then FSPF is
enabled on this interface on this VSAN. If set to
'down', then FSPF is disabled on this interface on this
VSAN.
This object meaningful only when 'fspfAdminStatus' is
up (1).rw Enumeration .1.3.6.1.4.1.9.9.287.1.2.1.17 |
fspfIfCreateTimeThe value of sysUpTime when this entry was last
created.ro LastCreationTime -- Rsyntax TimeTicks .1.3.6.1.4.1.9.9.287.1.2.1.18 |
fspfIfSetToDefaultSetting this value to 'default' changes the value of each
and every every write-able object in this row to its default
value.
If all the configuration parameters have their default values
and if the interface is down, then the row is deleted
automatically.
No action is taken if this object is set to 'noOp'.
The value of the object when read is always 'noOp'.rw Enumeration .1.3.6.1.4.1.9.9.287.1.2.1.19 |
fspfIfRowStatusThe status of the conceptual row.
This object can be used to create an entry only if the
corresponding VSAN is suspended and the interface is
either isolated or is a non-E_port. Otherwise, a create
will fail.
Setting this object to 'destroy' will always fail.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.287.1.2.1.20 |
fspfNbrStateChangeNotifyEnableSpecifies whether or not the local switch should
issue the notification 'fspfNbrStateChangeNotify'
when the local switch learns of a change in the
Neighbor's state (state in the FSPF Neighbor Finite
State Machine) on an interface on a VSAN.
If the value of the object is 'true, then the
notification is generated. If the value is 'false',
notification is not generated.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.287.1.3 |
fspfIfPrevNbrStateThe previous state of FSPF's 'neighbor state machine'
on an interface.
This object is to be used only as an object in the
notification 'fspfNbrStateChangeNotify'. FspfInterfaceState -- Rsyntax INTEGER { -- down(1), -- init(2), -- dbExchange(3), -- dbAckwait(4), -- dbWait(5), -- full(6) -- } .1.3.6.1.4.1.9.9.287.1.4 |
fspfDatabase OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.2 |
fspfLsrTableThis table is the database of all (the latest incarnation
of) the Link State Records (LSR) which are currently
contained in the topology database.
The topology database contains the LSRs which have been
either issued or received by the local switch on any/all
VSANs, and which have not reached fspfMaxAge. SEQUENCE OF FspfLsrEntry .1.3.6.1.4.1.9.9.287.2.1 |
fspfLsrEntryThis gives information for the most recent update of an
LSR. There is one entry for every LSR issued or received
by the local on a VSAN. FspfLsrEntry .1.3.6.1.4.1.9.9.287.2.1.1 |
fspfLsrDomainIdDomain Id of the LSR owner on this VSAN. It is the Link
State Id of this LSR. DomainId -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.2.1.1.1 |
fspfLsrTypeType of this LSR. FspfLsrType -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.2.1.1.2 |
fspfLsrAdvDomainIdDomain Id of the switch that is advertising the LSR on
the behalf of the switch owning it.ro DomainId -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.2.1.1.3 |
fspfLsrAgeTime since this LSR was inserted into the database.ro TimeIntervalSec .1.3.6.1.4.1.9.9.287.2.1.1.4 |
fspfLsrIncarnationNumberThe link state incarnation number of this LSR. This is
used to identify most recent instance of an LSR while
updating the topology database when an LSR is received.
The updating of an LSR includes incrementing its
incarnation number prior to transmission of the updated
LSR. So most recent LSR is the one with larger incarnation
number.ro Gauge .1.3.6.1.4.1.9.9.287.2.1.1.5 |
fspfLsrCheckSumThe checksum of the LSR.ro Gauge .1.3.6.1.4.1.9.9.287.2.1.1.6 |
fspfLsrLinksNumber of entries in the fspfLinkTable associated with
this LSR.ro Gauge .1.3.6.1.4.1.9.9.287.2.1.1.7 |
fspfLinkTableThis table contains the list of Inter-Switch Links and their
information which is part of the LSR received or issued. SEQUENCE OF FspfLinkEntry .1.3.6.1.4.1.9.9.287.2.2 |
fspfLinkEntryAn entry which contains information about a link
contained in an LSR on this VSAN. An entry is created
whenever a new link appears in an (issued or received)
LSR. Also, an entry is deleted when a link no longer
appears in an (issued or received) LSR. FspfLinkEntry .1.3.6.1.4.1.9.9.287.2.2.1 |
fspfLinkIndexAn arbitrary index of this link. Gauge .1.3.6.1.4.1.9.9.287.2.2.1.1 |
fspfLinkNbrDomainIdThe Domain Id of the neighbor on the other end of this
link on this VSAN.ro DomainId -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.2.2.1.2 |
fspfLinkPortIndexThe source E_port of this link, as indicated by the index
value in the LSR received from the switch identified by
'fspfLsrDomainId'.ro Gauge .1.3.6.1.4.1.9.9.287.2.2.1.3 |
fspfLinkNbrPortIndexThe destination E_port of this link, as indicated by the
index value in the LSR received from the switch identified
by 'fspfLinkNbrDomainId'.ro Gauge .1.3.6.1.4.1.9.9.287.2.2.1.4 |
fspfLinkTypeThe type of this link.ro FspfLinkType -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.287.2.2.1.5 |
fspfLinkCostThe cost of sending a frame on this link on this VSAN.
Link cost is calculated using a formula
link cost = S * (1.0625e12/Baud Rate)
where S (value of fspfIfCost object on inteface on the
switch corresponding to the domain Id) is the
administratively set cost factor for this interface.ro INTEGER .1.3.6.1.4.1.9.9.287.2.2.1.6 |
fspfNotificationPrefix OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.3 |
fspfNotification OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.3.0 |
fspfNbrStateChangeNotifyThis notification signifies that there has been a change
in the state of FSPF neighbors. This is generated when
the FSPF state regresses (e.g., goes from Full to init or
Down) or progresses (e.g., from any state to Full) to a
terminal state. The value of 'fspfIfNbrState' is the state
of the neighbor after the change. TRAP-TYPE .1.3.6.1.4.1.9.9.287.3.0.1 |
fspfMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4 |
fspfMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.1 |
fspfMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.1.1 |
fspfMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.2 |
fspfGenericGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.2.1 |
fspfIfGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.2.3 |
fspfDatabaseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.2.4 |
fspfNotificationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.287.4.2.5 |