CISCO-FRAME-RELAY-MIB
AI MIB Summary
The CISCO-FRAME-RELAY-MIB enables monitoring and management of Cisco Frame Relay interfaces, PVCs, and DLCIs to track LMI status, traffic counters, and virtual circuit states. It provides visibility into Frame Relay network health by exposing specific metrics such as in/out octet counts, packet drops, and PVC configuration parameters.
Cisco Frame Relay MIB
Main OID:
ciscoFrameRelayMIB.1.3.6.1.4.1.9.9.49
140
Objects
Active
Status
7
Dependencies
Imported Objects
Objects
140 total| Object Name |
|---|
ciscoFrameRelayMIBCisco Frame Relay MIB MODULE-IDENTITY .1.3.6.1.4.1.9.9.49 |
ciscoFrMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1 |
cfrLmiObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.1 |
cfrLmiTableTable of Frame Relay LMI information that are
either supplemental to the frDlcmiTable of RFC 1315
or specific to Cisco's implementation. SEQUENCE OF CfrLmiEntry .1.3.6.1.4.1.9.9.49.1.1.1 |
cfrLmiEntryEach entry of the table contains information
of Frame Relay LMI over one physical interface.
They are mostly FR generic and some Cisco specific. CfrLmiEntry .1.3.6.1.4.1.9.9.49.1.1.1.1 |
cfrLmiLinkstatusData link status via LMI.ro Enumeration .1.3.6.1.4.1.9.9.49.1.1.1.1.1 |
cfrLmiLinkTypeFrame Relay link type.ro Enumeration .1.3.6.1.4.1.9.9.49.1.1.1.1.2 |
cfrLmiEnquiryInsNumber of Status Enquiry messages received.ro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.3 |
cfrLmiEnquiryOutsNumber of Status Enquiry messages sent.ro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.4 |
cfrLmiStatusInsNumber of Status messages received.ro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.5 |
cfrLmiStatusOutsNumber of Status messages sent.ro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.6 |
cfrLmiUpdateStatusInsNumber of Update Status messages received.ro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.7 |
cfrLmiUpdateStatusOutsNumber of Update Status messages sentro Counter32 UNITS "messages" .1.3.6.1.4.1.9.9.49.1.1.1.1.8 |
cfrLmiStatusTimeoutsNumber of times when timeout occurred on waiting
for Status messagero Counter32 UNITS "times" .1.3.6.1.4.1.9.9.49.1.1.1.1.9 |
cfrLmiStatusEnqTimeoutsNumber of times when timeout occurred on waiting
for Status Enquiry messagero Counter32 UNITS "times" .1.3.6.1.4.1.9.9.49.1.1.1.1.10 |
cfrLmiN392DceLMI error threshold for DCE interface.
For DTE, value becomes 0.ro INTEGER .1.3.6.1.4.1.9.9.49.1.1.1.1.11 |
cfrLmiN393DceLMI monitored event count for DCE interface.
For DTE, value becomes zero (0).ro INTEGER .1.3.6.1.4.1.9.9.49.1.1.1.1.12 |
cfrLmiT392DceDCE polling verification timer for DCE interface
For DTE, the value becomes zero (0).ro INTEGER .1.3.6.1.4.1.9.9.49.1.1.1.1.13 |
cfrCircuitObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.2 |
cfrCircuitTableTable of descriptive and statistics information
that are generic to Frame Relay virtual circuits. SEQUENCE OF CfrCircuitEntry .1.3.6.1.4.1.9.9.49.1.2.1 |
cfrCircuitEntryEach entry of the table contains information of a
circuit that are not included in frCircuitTable of
RFC1315 but are generic to Frame Relay. CfrCircuitEntry .1.3.6.1.4.1.9.9.49.1.2.1.1 |
cfrCircuitDEinsNumber of packets received with the Discarded
Eligibility indictor (the DE bit) set.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.2.1.1.1 |
cfrCircuitDEoutsNumber of packets transmitted with DE bit set.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.2.1.1.2 |
cfrCircuitDropPktsOutsNumber of discarded packets that were to be sent.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.2.1.1.3 |
cfrCircuitTypeBasic circuit typero Enumeration .1.3.6.1.4.1.9.9.49.1.2.1.1.4 |
cfrExtCircuitTableTable of Cisco implementation specific FR
circuit information. This is a Cisco extension
for the frCircuitTable of RFC 1315. SEQUENCE OF CfrExtCircuitEntry .1.3.6.1.4.1.9.9.49.1.2.2 |
cfrExtCircuitEntryEach entry of the table contains information
of a Frame Relay virtual circuit that are specific
to Cisco implementation. CfrExtCircuitEntry .1.3.6.1.4.1.9.9.49.1.2.2.1 |
cfrExtCircuitIfNameThe textual name of the main interface or the
subinterface that this DLCI is associated with.
This is the same name string of an interface used
in the configuration and all console displays,
such as 'serial 0', 'serial 3/0.3', etc.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.2.2.1.1 |
cfrExtCircuitIfTypeType of the subinterface this DLCI is associated
with, if configured.ro Enumeration .1.3.6.1.4.1.9.9.49.1.2.2.1.2 |
cfrExtCircuitSubifIndexFor value greater than zero (0), it indicates
the network management interface index
for the subinterface associated with
this DLCI. Value 0 means the DLCI is not
associated with any subinterface.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.49.1.2.2.1.3 |
cfrExtCircuitMapStatusThe mapping protocols (internally considered as
the 'link type') applied on this circuit.
The value ranges from 0 to 2047.
For point-to-point DLCI, the value stays zero.
Otherwise, the value is a sum. It initially takes
the value zero, then, for each type of Protocol,
2 raised to a power is added to the sum.
The following table presents respective power and
equivalent value for each applicable type:
Protocol Power Value
- -
IP 0 1
IPX 1 2
Appletalk 2 4
XNS 3 8
VINES 4 16
DECnet 5 32
CLNS 6 64
Bridging 7 128
RSRB 8 256
STUN 9 512
LLC2 10 1024
For example, value 3 means the circuit's mapping
protocols include IP and IPX. (3 = 2**1 + 2**0,
where 0 corresponds to IP and 1 to IPX.) Value 0
means there is currently no mapping protocol for
the circuit.
See cfrMapTable for more mapping information.ro INTEGER .1.3.6.1.4.1.9.9.49.1.2.2.1.4 |
cfrExtCircuitCreateTypeIdentify the last source of the circuit's creation.ro Enumeration .1.3.6.1.4.1.9.9.49.1.2.2.1.5 |
cfrExtCircuitMulticastIndicate if this DLCI is a multicast DLCI.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.2.2.1.6 |
cfrExtCircuitRoutedDlciThe routed DLCI to pair up with this DLCI
for switching function. NOTE: Value zero (0)
indicates that there is no such routed DLCI
corresponding to this DLCI.ro DlciNumber .1.3.6.1.4.1.9.9.49.1.2.2.1.7 |
cfrExtCircuitRoutedIfThe interface for the routed DLCI that pairs up
with this DLCI for switching. Value greater than 0
is the InterfaceIndex for that interface. Value
zero (0) indicates that there is no such routed DLCI
corresponding to this DLCI.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.49.1.2.2.1.8 |
cfrExtCircuitUncompressInsNumber of inbound octets of the data packets,
accounted at Frame Relay level after FRF.9
payload decompression is applied. In the case of
non-FRF.9, this value could be identical to
frCircuitReceivedOctets, unless otherwise noted.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.2.2.1.9 |
cfrExtCircuitUncompressOutsNumber of outbound octets of the data packets,
accounted at Frame Relay level before FRF.9
payload compression is applied. In the case of
non-FRF.9, this value could be identical to
frCircuitSentOctets, unless otherwise noted.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.2.2.1.10 |
cfrExtCircuitFECNOutsTotal number of frames sent out to the network
indicating forward congestion.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.11 |
cfrExtCircuitBECNOutsTotal number of frames sent out to the network
indicating backward congestion.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.12 |
cfrExtCircuitMinThruputOutCircuit's outgoing minimal Throughput based on
configuration.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.13 |
cfrExtCircuitMinThruputInCircuit's incoming minimal Throughput based on
configuration.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.14 |
cfrExtCircuitBcastPktOutsTotal number of broadcast packets sent out to the
network.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.15 |
cfrExtCircuitBcastByteOutsTotal number of bytes sent out to the network in
broadcast packets.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.16 |
cfrExtCircuitBandwidthBandwidth of the virtual circuit, acquired from
Cisco typed LMI Full Status message.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.17 |
cfrExtCircuitShapeByteLimitMaximum number of tokens a token bucket can hold in any
time interval in case of traffic shaping.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.18 |
cfrExtCircuitShapeIntervalCommitted rate measurement interval.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.19 |
cfrExtCircuitShapeByteIncrementNumber of tokens added into the token bucket per time
interval in case of traffic shaping.ro Integer32 .1.3.6.1.4.1.9.9.49.1.2.2.1.20 |
cfrExtCircuitShapePktsTotal number of packets that went through traffic
shaping.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.21 |
cfrExtCircuitShapeBytesTotal number of bytes that went through traffic
shaping.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.2.2.1.22 |
cfrExtCircuitShapePktsDelayTotal number of packets that were delayed by the
traffic shaper.ro Counter32 .1.3.6.1.4.1.9.9.49.1.2.2.1.23 |
cfrExtCircuitShapeBytesDelayTotal number of bytes that were delayed by the
traffic shaper.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.2.2.1.24 |
cfrExtCircuitShapeActiveShows whether shaping is active or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.2.2.1.25 |
cfrExtCircuitShapeAdaptingType of Adaptive Shaping configured.
none(1) - No adaptive shaping configured
becn(2) - Backward Explicit Congestion Notification
foreSight(3) - ForeSight is the network traffic control
software used in Cisco WAN switchesro Enumeration .1.3.6.1.4.1.9.9.49.1.2.2.1.26 |
cfrExtCircuitTxDataRateThe average rate (bytes/second) at which data is
transmitted in this circuit.ro INTEGER .1.3.6.1.4.1.9.9.49.1.2.2.1.27 |
cfrExtCircuitTxPktRateThe average number of packets sent in a second in this
circuit.ro INTEGER .1.3.6.1.4.1.9.9.49.1.2.2.1.28 |
cfrExtCircuitRcvDataRateThe average rate (bytes/second) at which data is
received in this circuit.ro INTEGER .1.3.6.1.4.1.9.9.49.1.2.2.1.29 |
cfrExtCircuitRcvPktRateThe average number of packets received in a second in
this circuit.ro INTEGER .1.3.6.1.4.1.9.9.49.1.2.2.1.30 |
cfrMapObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.3 |
cfrMapTableTable of protocols and addresses mapping
information of FR virtual circuit. SEQUENCE OF CfrMapEntry .1.3.6.1.4.1.9.9.49.1.3.1 |
cfrMapEntryEach entry of the table contains one mapping
information of a Frame Relay virtual circuit. CfrMapEntry .1.3.6.1.4.1.9.9.49.1.3.1.1 |
cfrMapIndexAn arbitrary Index to the mapping information
associated with a certain circuit. The maximum
value is arbitrarily picked which is considered
sufficient for usual configuration.ro INTEGER .1.3.6.1.4.1.9.9.49.1.3.1.1.1 |
cfrMapProtocolMapping protocol for this circuit.ro CfrMapProtocols .1.3.6.1.4.1.9.9.49.1.3.1.1.2 |
cfrMapAddressMapping protocol address at remote end for
this DLCI.
NOTE: For point-to-point DLCI, the string is fixed
to be point-to-point.ro OCTET STRING .1.3.6.1.4.1.9.9.49.1.3.1.1.3 |
cfrMapTypeType for the map creation.ro Enumeration .1.3.6.1.4.1.9.9.49.1.3.1.1.4 |
cfrMapEncapsIndication of the encapsulation type for this
mapping protocol.ro Enumeration .1.3.6.1.4.1.9.9.49.1.3.1.1.5 |
cfrMapBroadcastBroadcast enabled or disabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.3.1.1.6 |
cfrMapPayloadCompressIndicate if payload compression is enabled.rodeprecated TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.3.1.1.7 |
cfrMapTcpHdrCompressTCP header compression type, if applicable.ro Enumeration .1.3.6.1.4.1.9.9.49.1.3.1.1.8 |
cfrMapRtpHdrCompressRTP header compression type, if applicable.
The value 'passive' means that the header of an
outgoing RTP/IP packet is compressed only if an
incoming RTP/IP packet had a compressed header.
The value 'active' means the header of every outgoing
RTP/IP packet is compressed.ro Enumeration .1.3.6.1.4.1.9.9.49.1.3.1.1.9 |
cfrMapPayloadCompressTypeFR payload compression type, if applicable.
FRF.9 is the Frame Relay Forum Implementation Agreement
on FR payload compression. The compression can be done
by either software or hardware (when equipped with the
supporting hardware), depending on configuration.ro Enumeration .1.3.6.1.4.1.9.9.49.1.3.1.1.10 |
cfrSvcObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.4 |
cfrSvcTableTable of FR SVC specific, descriptive
and statistics information. SEQUENCE OF CfrSvcEntry .1.3.6.1.4.1.9.9.49.1.4.1 |
cfrSvcEntryEach entry of the table contains circuit information
specific to a Frame Relay Switched Virtual Circuit. CfrSvcEntry .1.3.6.1.4.1.9.9.49.1.4.1.1 |
cfrSvcAddrLocalLocal E.164/X.125 address for the circuit.ro OCTET STRING .1.3.6.1.4.1.9.9.49.1.4.1.1.1 |
cfrSvcAddrRemoteRemote E.164/X.125 address for the circuit.ro OCTET STRING .1.3.6.1.4.1.9.9.49.1.4.1.1.2 |
cfrSvcThroughputInCircuit's incoming throughput. For outgoing
throughput (commonly referred to as CIR) see
frCircuitThroughput per RFC1315.ro Integer32 .1.3.6.1.4.1.9.9.49.1.4.1.1.3 |
cfrSvcMinThruputOutCircuit's outgoing minimal Throughput.rodeprecated Integer32 .1.3.6.1.4.1.9.9.49.1.4.1.1.4 |
cfrSvcMinThruputInCircuit's incoming minimal Throughput.rodeprecated Integer32 .1.3.6.1.4.1.9.9.49.1.4.1.1.5 |
cfrSvcCommitBurstInCircuit's incoming Committed Burst Rate.
See ANSI and/or ITU specifications for
definition and calculations. For outgoing
CBR, see frCircuitCommittedBurst per RFC 1315.ro Integer32 .1.3.6.1.4.1.9.9.49.1.4.1.1.6 |
cfrSvcExcessBurstInCircuit's incoming Excess Burst Rate.
See ANSI and/or ITU specifications for
definition and calculations. For outgoing
EBR, see frCircuitExcessBurst per RFC 1315.ro Integer32 .1.3.6.1.4.1.9.9.49.1.4.1.1.7 |
cfrSvcIdleTimeCircuit's idle time period. If expires, the
circuit is cleared.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.9.9.49.1.4.1.1.8 |
cfrElmiObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.5 |
cfrElmiIpAddrThis object represents the Management address of the
device used for address registration.
Network management station can send management
messages to this IP address. This can be
user configured address or the address of one of the
interfaces on the device. If address registration is
disabled then this will have a value of 0.0.0.0.
This object is accessible only if the ELMI protocol
is supported on the devicero IpAddress .1.3.6.1.4.1.9.9.49.1.5.1 |
cfrElmiTableTable of CISCO Frame Relay ELMI information that is
specific to CISCO implementation SEQUENCE OF CfrElmiEntry .1.3.6.1.4.1.9.9.49.1.5.2 |
cfrElmiEntryEach entry of the table contains information about a
physical interface. The table can be accessible only
if the device supports ELMI protocol and if LMI is
enabled on the interface. CfrElmiEntry .1.3.6.1.4.1.9.9.49.1.5.2.1 |
cfrElmiLinkStatusThis variable states whether Enhanced Link Management
Interface(ELMI) protocol is enabled or not on a
frame relay interface.ro Enumeration .1.3.6.1.4.1.9.9.49.1.5.2.1.1 |
cfrElmiArStatusThis variable states whether the Enhanced Link
Management Interface(ELMI) address registration(AR)
mechanism is enabled or not on a frame relay
interface. A value of 1 indicates ELMI AR is
supported on the interface. A value of 2 indicates
ELMI AR is supported but the user disabled the
exchange of IP address and ifIndex with the
neighboring device. This object doesn't have any
significance if cfrElmiLinkStatus is disabled
on the interface.ro Enumeration .1.3.6.1.4.1.9.9.49.1.5.2.1.2 |
cfrElmiRemoteStatusThis variable states the Enhanced Link
Management(ELMI) status on the other end of the
interface. If cfrElmiLinkStatus is enabled on the
other end a value of 1 will be returned,
else 2 will be returned. This object doesn't have any
significance if cfrElmiLinkStatus is disabled on the
interfacero Enumeration .1.3.6.1.4.1.9.9.49.1.5.2.1.3 |
cfrElmiNeighborTableTable of CISCO Frame Relay Neighbor ELMI information
that is specific to CISCO implementation. SEQUENCE OF CfrElmiNeighborEntry .1.3.6.1.4.1.9.9.49.1.5.3 |
cfrElmiNeighborEntryEach entry of the table contains information of the
neighboring device connected to a physical interface.
The entry will be present only if ELMI is enabled on
the neighboring device interface. If the value of the
cfrElmiRemoteStatus in the cfrElmiEntry is 1 then a
valid entry exists for the interface. If ELMI is not
supported on the remote end then, the neighbor
information for the interface will not be present CfrElmiNeighborEntry .1.3.6.1.4.1.9.9.49.1.5.3.1 |
cfrElmiNeighborArStatusThis variable indicates the status of ELMI Address
registration(AR) on the neighboring device. A value
of 1 indicates ELMI AR is not supported on the
neighboring device. A value of 2 indicates ELMI AR is
enabled on the interface. A value of 3 indicates AR is
supported, but user disabled the exchange of IP
address and ifIndex with the neighbor.ro Enumeration .1.3.6.1.4.1.9.9.49.1.5.3.1.1 |
cfrElmiNeighborIpAddressThe Management IP address of the neighboring device
to which the other end of this interface is
connected. Network management system can use this
address to send management messages to the device.
If address registration is not supported on the
remote end then the value will be 0.0.0.0.
NMS uses this object in the topology discovery of the
network.ro IpAddress .1.3.6.1.4.1.9.9.49.1.5.3.1.2 |
cfrElmiNeighborIfIndexThe Interface index of the neighboring device to
which this interface is connected. If the value of
cfrElmiNeighborArStatus is 2 then this will have a
valid value. If the value of cfrElmiNeighborArStatus
is 3 or 1 then value of this object will be 0. NMS
uses this object in the topology discovery of the
network.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.9.9.49.1.5.3.1.3 |
cfrElmiNeighborVendorNameVendor name of the neighboring device to which the
other end of this interface is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.5.3.1.4 |
cfrElmiNeighborPlatformNamePlatform name of the neighboring device to which the
other end of this interface is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.5.3.1.5 |
cfrElmiNeighborDeviceNameDevice name of the neighboring device to which the
other end of this interface is connected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.5.3.1.6 |
cfrFragObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.6 |
cfrFragTableTable of Frame Relay Fragmentation information.
These are specific to Cisco's implementation. SEQUENCE OF CfrFragEntry .1.3.6.1.4.1.9.9.49.1.6.1 |
cfrFragEntryEach entry of the table contains details of
fragmentation configured on this circuit. CfrFragEntry .1.3.6.1.4.1.9.9.49.1.6.1.1 |
cfrFragSizecfrFragSize defines the payload size of a fragment
and it excludes the FR headers and any FR fragmentation
header.ro INTEGER .1.3.6.1.4.1.9.9.49.1.6.1.1.1 |
cfrFragTypeFragmentation type configured by the user. The types
supported are end-to-end, VoFR-cisco and VoFR.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.6.1.1.2 |
cfrFragInPktsTotal number of frames received that have a
fragmentation header.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.3 |
cfrFragOutPktsTotal number of fragments that are transmitted with a
fragmenation header.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.4 |
cfrFragInOctetsTotal number of bytes received in frames that have a
fragmentation header. The number of bytes include the
FR header.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.5 |
cfrFragOutOctetsTotal number of bytes that are transmitted in frames
with a fragmenation header. The number of bytes also
includes the FR header.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.6 |
cfrFragNotInPktsTotal number of frames received that do not require
reassembly and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.7 |
cfrFragNotOutPktsTotal number of frames transmitted without fragmenting
and therefore will not contain the fragmentation header.
This counter is valid only when end-to-end fragmentation
type is set.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.8 |
cfrFragNotInOctetsTotal number of bytes received in frames that do not
require reassembly and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.9 |
cfrFragNotOutOctetsTotal number of bytes transmitted in frames that are
not fragmented and therefore will not contain the
fragmentation header. This counter is valid only when
end-to-end fragmentation type is set.ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.10 |
cfrFragAssembledInPktsTotal number of fully reassembled frames. It also
counts the number of packets received without FR
fragmentation header (i.e. in un-fragmentated pkts).ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.11 |
cfrFragAssembledInOctetsTotal number of bytes received in fully reassembled
frames. It also counts the number of packets received
without FR fragmentation header (i.e.in un-fragmentated
pkts).ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.12 |
cfrFragPreOutPktsTotal number of frames fragmented and trasmitted. It
also counts the number of packets trasmitted without FR
fragmentation header (i.e. in un-fragmentated pkts).ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.13 |
cfrFragPreOutOctetsTotal number of bytes transmitted in fragmented frames.
It also counts the number of bytes trasmitted in frames
without FR fragmentation header (i.e. in un-fragmentated
pkts).ro Counter32 UNITS "octets" .1.3.6.1.4.1.9.9.49.1.6.1.1.14 |
cfrFragDroppedReAssembledInPktsNumber of received fragments dropped for reasons such
as : running out of memory, receiving segments out of
sequence, receiving an unexpected frame with a B bit
set, timing out on a reassembling frame.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.15 |
cfrFragDroppedFragmentedOutPktsNumber of fragments dropped because of running
out of memory.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.16 |
cfrFragTimeoutsInNumber of reassemble timer timeouts for this circuit.
A frame requiring more than two minutes to fully
reassemble is dropped and timeout will be incremented
by one.ro INTEGER .1.3.6.1.4.1.9.9.49.1.6.1.1.17 |
cfrFragOutOfSeqFragPktsIndicates the total number of packets received with an
unexpected sequence number. All fragments being
reassembled are dropped. Start a new packet with the
received segment only if the B bit is set on the
segment. Otherwise the new segment is also dropped.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.18 |
cfrFragUnexpectedBBitSetPktsNumber of fragments received in this circuit with
a B bit set. All fragments being reassembled are dropped
and a new packet is started with this segment.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.19 |
cfrFragSeqMissedPktsNumber of fragments received in this circuit with
skipped sequence number.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.20 |
cfrFragInterleavedOutPktsNumber of packets that have been interleaved between
segments.ro Counter32 UNITS "packets" .1.3.6.1.4.1.9.9.49.1.6.1.1.21 |
cfrConnectionObjs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.1.7 |
cfrConnectionTableTable of Frame Relay/Frame Relay and Frame Relay/ATM
Network/Service Interworking connection information.
These are specific to Cisco's implementation. SEQUENCE OF CfrConnectionEntry .1.3.6.1.4.1.9.9.49.1.7.1 |
cfrConnectionEntryEach entry of the table contains information of a
connection that is established for Frame Relay/Frame
Relay and Frame Relay/ATM Network/Service Interworking. CfrConnectionEntry .1.3.6.1.4.1.9.9.49.1.7.1.1 |
cfrConnNameThe textual name of a for FR/FR or FR/ATM
Network/Service Interworking connection.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.7.1.1.1 |
cfrConnIDThe numerical identifier of a FR/FR or FR/ATM
Network/Service Interworking connection.ro INTEGER .1.3.6.1.4.1.9.9.49.1.7.1.1.2 |
cfrConnStateStatus of a FR/FR or FR/ATM Network/Service
Interworking connection.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.7.1.1.3 |
cfrConnSegment1NameThe textual name used to identify the first segment of
a FR/FR or FR/ATM Network/Service Interworking
connection.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.7.1.1.4 |
cfrConnSegment1VCGroupThe textual name used to identify the VC-Group in the
first segment of a Frame Relay/ATM Network Interworking
(FRF.5)connection.
This field is not applicabe in case of,
FRF.8 (Frame Relay/ATM Service Interworking)
and
FR-FR connectione.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.7.1.1.5 |
cfrConnSegment1DlciThe DLCI used as the first segment of a FR-FR or FR-ATM
Network/Service Interworking connection.ro DlciNumber .1.3.6.1.4.1.9.9.49.1.7.1.1.6 |
cfrConnSegment2NameThe interface on which second segment of a FR-FR or
FR-ATM Network/Service Interworking connection is
configured.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9.9.49.1.7.1.1.7 |
cfrConnSegment2VpiThe value of VPI, in the ATM connection, used as the
second segment of a FR-ATM Network/Service Interworking
connection. In case of FR-FR connection, the same will
be used to display the DLCI used as the second segment.ro INTEGER .1.3.6.1.4.1.9.9.49.1.7.1.1.8 |
cfrConnSegment2VciThe value of VCI, in the ATM connection, used as the
second segment of a FR-ATM Network/Service Interworking
connection. In case of FR-FR connection, this is not
supported.ro INTEGER .1.3.6.1.4.1.9.9.49.1.7.1.1.9 |
cfrConnServiceTranslationShows whether Service Translation Mode is supported or
not. Translation Mode is the interworking of
internetworking (routed and/or bridged) protocols used
in FR-ATM Service PVC Interworking(FRF.8).
This is not supported in case of FRF.5 (FR-ATM network
Interworking) and FR-FR connections.ro Enumeration .1.3.6.1.4.1.9.9.49.1.7.1.1.10 |
cfrConnFrSscsDlciThe DLCI value used at the FR-SSCS layer. This is one of
connection multiplexing methods used in Frame Relay/ATM
Network Interworking.
Not supported in case of FRF.8 (FR-ATM Service PVC
Interworking) and FR-FR connectionsro DlciNumber .1.3.6.1.4.1.9.9.49.1.7.1.1.11 |
cfrConnEfciBitShows whether the FECN field in the FR frame is mapped
to the ATM EFCI field of every cell generated out of the
FR frame. This is used to indicate congestion in FR to
ATM direction in case of Frame Relay/ATM Service PVC
Interworking.
Not supported in FRF.5 (Frame Relay/ATM Network
Interworking and FR-FR connections.ro Enumeration .1.3.6.1.4.1.9.9.49.1.7.1.1.12 |
cfrConnDeBitThe method of operation for loss priority mapping in the
B-ISDN to FR direction..
Not supported in case of FR-FR connection.ro Enumeration .1.3.6.1.4.1.9.9.49.1.7.1.1.13 |
cfrConnClpBitThe method of operation used to map loss priority
mapping in the FR to ATM direction.
Not supported in case of FR-FR connection.ro Enumeration .1.3.6.1.4.1.9.9.49.1.7.1.1.14 |
ciscoFrMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.3 |
ciscoFrMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.3.1 |
ciscoFrMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.49.3.2 |