CISCO-FLOW-MONITOR-TC-MIB
The CISCO-FLOW-MONITOR-TC-MIB provides the textual conventions required to define flow monitoring objects on Cisco IOS and IOS-XE devices, enabling the management of traffic flow metrics, alarm conditions, and measurement intervals via SNMP. It standardizes the data types for flow sets, flow monitors, and standing conditions to facilitate the collection and analysis of unidirectional traffic streams for performance monitoring and fault detection.
Imported Objects
Objects
1 total| Object Name |
|---|
ciscoFlowMonitorTcMIB MODULE-IDENTITY .1.3.6.1.4.1.9.9.688 |
CISCO-FLOW-MONITOR-TC-MIB Technical Reference Overview
The CISCO-FLOW-MONITOR-TC-MIB SNMP MIB module published by Cisco defines 1 managed OID objects, including 0 scalar/column metrics, 0 SNMP tables, and 0 trap/notification events anchored at base OID .1.3.6.1.4.1.9.9.688.
Key OID Definitions in CISCO-FLOW-MONITOR-TC-MIB
.1.3.6.1.4.1.9.9.688This MIB module defines textual conventions used by the MIB modules defining objects describing flow monitoring. GLOSSARY ============ Alarm Action - a method used by the device to signal changes in an alarm condition. Alarm Aggregation - a technique used to efficiently monitor the same standing condition for a flow set. Alarm Condition - a standing condition for which the device signals changes in state. Alarm Group - a flow set for which the device monitors a configured standing condition, raising an alarm when a configured number of flows in the flow set assert the standing standing. Alarm Severity - the relative disposition of an alarm condition when raised by the device. For example, a provider may regard a flow stop alarm as having a higher severity than a flow's loss fraction exceeding a configured threshold. Flow Monitor - a hardware or software entity that classifies traffic flows, collects flow data, and periodically computes flow metrics. Flow Metric - a measurement that reflects the quality of a traffic flow. Flow Point - represents the ingress or egress of a traffic flow. Flow Set - a group of traffic flows. Measurement Interval - the length of time over which a flow monitor collects data related to a traffic flow, after which the flow monitor computes flow metrics using the collected data. Standing Condition - represents a lasting error, fault, or warning resulting from the application of a set of criteria to the state of an entity, such as a flow monitor or traffic flow. For example, a flow monitor may assert a standing condition if the number of traffic flows that expire in a meansurement interval exceeds a configured threshold. Traffic Flow - a unidirectional stream of packets conforming to a classifier. For example, packets having a particular source IP address, destination IP address, protocol type, source port number, and destination port number.
More MIBs from Cisco
Browse all CiscoMIBs →The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.
The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.
The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.
SNMP MIB module
The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.
The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.