CISCO-ETHERLIKE-EXT-MIB
AI MIB Summary
The CISCO-ETHERLIKE-EXT-MIB extends standard EtherLike-MIB monitoring on Cisco network devices by exposing vendor-specific and previously excluded Ethernet interface statistics, including extended error counters, collision details, and interface operational states. This module enables granular troubleshooting of Layer 2 link integrity and performance anomalies on Cisco switches and routers that are not covered by the generic IEEE 802.3 MIB definitions.
The MIB module to describe generic objects for ethernet-like network interfaces.
This MIB provides ethernet-like network interfaces information that are either excluded by EtherLike-MIB or specific to Cisco products.
Main OID:
ciscoEtherExtMIB.1.3.6.1.4.1.9.9.645
15
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
15 total| Object Name |
|---|
ciscoEtherExtMIBThe MIB module to describe generic objects for
ethernet-like network interfaces.
This MIB provides ethernet-like network interfaces
information that are either excluded by EtherLike-MIB
or specific to Cisco products. MODULE-IDENTITY .1.3.6.1.4.1.9.9.645 |
ciscoEtherExtMIBNotifs OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.0 |
ciscoEtherExtMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.1 |
ceeDot3PauseExt OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.1.1 |
ceeDot3PauseExtTableA list of additional descriptive and status
information about the MAC Control PAUSE
function on the ethernet-like interfaces
attached to a particular system, in extension to
dot3PauseTable in EtherLike-MIB. There will be
one row in this table for each ethernet-like
interface in the system which supports the MAC
Control PAUSE function. SEQUENCE OF CeeDot3PauseExtEntry .1.3.6.1.4.1.9.9.645.1.1.1 |
ceeDot3PauseExtEntryAn entry in the table, containing additional
information about the MAC Control PAUSE function
on a single ethernet-like interface, in extension
to dot3PauseEntry in Etherlike-MIB. CeeDot3PauseExtEntry .1.3.6.1.4.1.9.9.645.1.1.1.1 |
ceeDot3PauseExtAdminModeIndicates preference to send or process pause
frames on this interface.
txDesired(0) - indicates preference to send pause
frames, but autonegotiates flow
control. This bit can only be
turned on when the corresponding
instance of dot3PauseAdminMode
has the value of 'enabledXmit' or
'enabledXmitAndRcv'.
rxDesired(1) - indicates preference to process
pause frames, but autonegotiates
flow control. This bit can only be
turned on when the corresponding
instance of dot3PauseAdminMode
has the value of 'enabledRcv' or
'enabledXmitAndRcv'.rw Bits .1.3.6.1.4.1.9.9.645.1.1.1.1.1 |
ceeDot3PauseExtOperModeProvides additional information about the flow
control operational status on this interface.
txDisagree(0) - the transmit pause function on
this interface is disabled due to
disagreement from the far end on
negotiation.
rxDisagree(1) - the receive pause function on
this interface is disabled due to
disagreement from the far end on
negotiation.
txDesired(2) - the transmit pause function on
this interface is desired.
rxDesired(3) - the receive pause function on
this interface is desired.ro Bits .1.3.6.1.4.1.9.9.645.1.1.1.1.2 |
ceeSubIf OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.1.2 |
ceeSubInterfaceTableThis table provides the subinterface related information
associated to the Ethernet-like interfaces.
The subinterface is a division of one physical interface into
multiple logical interfaces. As an example of what a typical
subinterface setup might look like on a device, a single
Ethernet port such as GigabitEthernet0/0 would be subdivided
into Gi0/0.1, Gi0/0.2, Gi0/0.3 and so on, each one performing as
if it were a separate interface. SEQUENCE OF CeeSubInterfaceEntry .1.3.6.1.4.1.9.9.645.1.2.1 |
ceeSubInterfaceEntryThis table contains a row for each Ethernet-like interface
by it's ifTable ifIndex in the system, which supports the
sub-interface.
An entry is created by an agent, when it detects a
Ethernet-like interface is created in ifTable and it
can support sub-interface.
An entry is deleted by an agent, when the ifTable entry
associated to the Ethernet-like interface is deleted.
Typically, when the card is removed from the device. CeeSubInterfaceEntry .1.3.6.1.4.1.9.9.645.1.2.1.1 |
ceeSubInterfaceCountThis object represents the number of subinterfaces
created on a Ethernet-like interface.ro Unsigned32 .1.3.6.1.4.1.9.9.645.1.2.1.1.1 |
ciscoEtherExtMIBConform OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.2 |
ceeEtherExtMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.2.1 |
ceeEtherExtMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.645.2.2 |