Home/Catalog/CISCO-DS3-MIB

CISCO-DS3-MIB

AI MIB Summary

The CISCO-DS3-MIB extends standard DS3 monitoring to expose Cisco-specific line objects and performance counters for T1/E1/DS3 interfaces, enabling granular tracking of signal status, error rates (SEF, UAS), and line provisioning parameters on Cisco routers and switches.

The MIB module to describe DS3 line objects. This is an extension to the standard DS3 MIB(RFC 2496).
142
Objects
Active
Status
5
Dependencies

Imported Objects

Objects

142 total
Object Name
ciscoDs3MIB
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132
RFC1155-SMI
Unknown
.1.3.6.1.4.1.9.9.132
ciscoDs3MIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132.1
cds3Config
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132.1.1
cds3ConfigTable
SEQUENCE OF Cds3ConfigEntry
.1.3.6.1.4.1.9.9.132.1.1.1
cds3ConfigEntry
Cds3ConfigEntry
.1.3.6.1.4.1.9.9.132.1.1.1.1
cds3LineTyperw
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.1
cds3LineAIScBitsCheckrw
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.2
cds3LineRcvFEACValidationrw
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.3
cds3LineOOFCriteriarw
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.4
cds3TraceToTransmitrw
DisplayString
.1.3.6.1.4.1.9.9.132.1.1.1.1.5
cds3TraceToExpectrw
DisplayString
.1.3.6.1.4.1.9.9.132.1.1.1.1.6
cds3TraceAlarmro
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.7
cds3InternalEqualizerrw
Enumeration
.1.3.6.1.4.1.9.9.132.1.1.1.1.8
cds3NearEndLineLoopbackStatusro
Gauge
.1.3.6.1.4.1.9.9.132.1.1.1.1.9
cds3FarEndLineLoopbackStatusro
Gauge
.1.3.6.1.4.1.9.9.132.1.1.1.1.10
cds3Alarm
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132.1.2
cds3AlarmConfig
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132.1.2.1
cds3AlarmConfigTable
SEQUENCE OF Cds3AlarmConfigEntry
.1.3.6.1.4.1.9.9.132.1.2.1.1
cds3AlarmConfigEntry
Cds3AlarmConfigEntry
.1.3.6.1.4.1.9.9.132.1.2.1.1.1
cds3NEAlarmUpCountrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.1
cds3NEAlarmDownCountrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.2
cds3NEAlarmThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.3
cds3FEAlarmUpCountrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.4
cds3FEAlarmDownCountrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.5
cds3FEAlarmThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.6
cds3StatisticalAlarmSeverityrw
Enumeration
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.7
cds3LCV15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.8
cds3LCV24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.9
cds3LES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.10
cds3LES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.11
cds3PCV15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.12
cds3PCV24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.13
cds3PES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.14
cds3PES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.15
cds3PSES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.16
cds3PSES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.17
cds3SEFS15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.18
cds3SEFS24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.19
cds3UAS15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.20
cds3UAS24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.21
cds3CCV15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.22
cds3CCV24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.23
cds3CES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.24
cds3CES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.25
cds3CSES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.26
cds3CSES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.27
cds3LSES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.28
cds3LSES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.29
cds3LineStatisticalAlarmStatero
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.30
cds3AlarmConfigPlcpTable
SEQUENCE OF Cds3AlarmConfigPlcpEntry
.1.3.6.1.4.1.9.9.132.1.2.1.2
cds3AlarmConfigPlcpEntry
Cds3AlarmConfigPlcpEntry
.1.3.6.1.4.1.9.9.132.1.2.1.2.1
cds3PlcpStatisticalAlarmSeverityrw
Enumeration
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.1
cds3PlcpBip8CV15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.2
cds3PlcpBip8CV24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.3
cds3PlcpBip8ES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.4
cds3PlcpBip8ES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.5
cds3PlcpBip8SES15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.6
cds3PlcpBip8SES24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.7
cds3PlcpSEFS15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.8
cds3PlcpSEFS24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.9
cds3PlcpUAS15MinThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.10
cds3PlcpUAS24HrThresholdrw
Gauge
.1.3.6.1.4.1.9.9.132.1.2.1.2.1.11
cds3AlarmPlcpTable
SEQUENCE OF Cds3AlarmPlcpEntry
.1.3.6.1.4.1.9.9.132.1.2.2
cds3AlarmPlcpEntry
Cds3AlarmPlcpEntry
.1.3.6.1.4.1.9.9.132.1.2.2.1
cds3PlcpLineAlarmStatero
Gauge
.1.3.6.1.4.1.9.9.132.1.2.2.1.1
cds3PlcpLineStatisticalAlarmStatero
Gauge
.1.3.6.1.4.1.9.9.132.1.2.2.1.2
cds3PlcpBip8CVCurrentro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.3
cds3PlcpBip8CV24HrBucketro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.4
cds3PlcpBip8ESCurrentro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.5
cds3PlcpBip8ES24HrBucketro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.6
cds3PlcpBip8SESCurrentro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.7
cds3PlcpBip8SES24HrBucketro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.8
cds3PlcpSEFSCurrentro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.9
cds3PlcpSEFS24HrBucketro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.10
cds3PlcpUASCurrentro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.11
cds3PlcpUAS24HrBucketro
Counter
.1.3.6.1.4.1.9.9.132.1.2.2.1.12
cds3Stats
OBJECT IDENTIFIER
.1.3.6.1.4.1.9.9.132.1.3
cds3StatsTable
SEQUENCE OF Cds3StatsEntry
.1.3.6.1.4.1.9.9.132.1.3.1
cds3StatsEntry
Cds3StatsEntry
.1.3.6.1.4.1.9.9.132.1.3.1.1
cds3RcvLOSCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.1
cds3RcvOOFCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.2
cds3RAICountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.3
cds3CCVCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.4
cds3FECountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.5
cds3EXZSCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.6
cds3LCVCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.7
cds3PCVCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.8
cds3CPECountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.9
cds3FEBECountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.10
cds3RcvAISCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.1.1.11
cds3PlcpStatsTable
SEQUENCE OF Cds3PlcpStatsEntry
.1.3.6.1.4.1.9.9.132.1.3.2
cds3PlcpStatsEntry
Cds3PlcpStatsEntry
.1.3.6.1.4.1.9.9.132.1.3.2.1
cds3PlcpRcvBip8Countro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.1
cds3PlcpRcvOOFCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.2
cds3PlcpRcvRAICountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.3
cds3PlcpFECountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.4
cds3PlcpFESecCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.5
cds3PlcpSEFSecCountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.6
cds3PlcpFEBECountro
Counter
.1.3.6.1.4.1.9.9.132.1.3.2.1.7
Showing 100 of 142 OID objects

CISCO-DS3-MIB Technical Reference Overview

The CISCO-DS3-MIB SNMP MIB module published by Cisco defines 142 managed OID objects, including 108 scalar/column metrics, 9 SNMP tables, and 0 trap/notification events. Key tabular structures include cds3ConfigTable, cds3AlarmConfigTable, cds3StatsTable, cds3AlarmConfigPlcpTable, cds3AlarmPlcpTable, cds3PlcpStatsTable.

Key OID Definitions in CISCO-DS3-MIB

cds3ConfigTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.1.1

The DS3 Configuration table. The table has objects for configuring a T3/E3 line.

cds3AlarmConfigTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.2.1.1

The DS3 interface alarm configuration table. This table contains the parameters associated with detecting and declaring alarms for the interface. The parameters include severity of alarm, alarm integration parameters and 15 minute and 24 hour thresholds.

cds3StatsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.3.1

T3/E3 Statistics table. This table maintains the number of times the line encountered Loss of Signal(LOS), out of frame(LOF), Alarm Indication signals(AIS), Remote alarm indications(RAI), C-bit coding violations(CCV), Framing Errors(FE), from the time it is up. Line fails and goes down as a result of failures. When the line is brought back up again by the user the error statistics are cleared.

cds3AlarmConfigPlcpTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.2.1.2

The ATM interface PLCP alarm configuration table. PLCP is a sublayer over the DS3 interface, that carries ATM cells.

cds3AlarmPlcpTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.2.2

The Plcp interface alarm table. This table maintains the CV,ES,SES, SEFS and UAS for DS3 line with Plcp framing selected. Please refer to RFC2496 for description of these various error statistics.

cds3PlcpStatsTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.3.2

T3 Plcp Statistics table. This table maintains the errors encountered by the T3 line with Plcp frame format selected, from the time the line is up.Line fails and goes down as a result of failures. When the line is brought back up again by the user after eliminating the error conditions, the statistics are cleared.

cds3IntervalTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.3.4

The DS3 interface interval table.

cds3Current24HrTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.3.5

The DS3 interface current 24 hour table. This table contains counters for current 24 hour interval. Threshold on this counters are configured through cds3AlarmConfigTable table. 24 hour interval is aligned to wall clock.

cds3Previous24HrTableSEQUENCEnot-accessible
.1.3.6.1.4.1.9.9.132.1.3.6

The DS3 interface previous 24 hour table. This table contains counters for previous 24 hour interval. Implementation of this table is optional.

cds3ConfigEntryCds3ConfigEntrynot-accessible
.1.3.6.1.4.1.9.9.132.1.1.1.1

An entry in the table. There is an entry for each available T3/E3 line, with an ifType value of 'ds3'(30). By default, lines are disabled. 'ifAdmin' from ifTable must be used to up the line. The objects in this table can be modified only when the line is up.

cds3LineTypeINTEGERread-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.1

This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps. The values, in sequence, describe: Following values are applicable to DS3 interfaces only. ds3cbitadm : Indicates C-BIT ADM mode ds3cbitplcp : Indicates C-BIT PLCP mode ds3m23adm : Indicates M23 ADM mode ds3m23plcp : Indicates M23 PLCP mode dsx3M23 : Refer ANSI T1.107-1988 [9] dsx3SYNTRAN : Refer ANSI T1.107-1988 [9] dsx3CbitParity : Refer ANSI T1.107-1988 [9] dsx3ClearChannel : Refer ANSI T1.107-1988 [9] ds3cbitfrmronly : Indicates C-BIT FRAMER-ONLY mode ds3m23frmronly : Indicates M23 FRAMER-ONLY mode Following values are applicable to E3 interfaces only. e3g832adm : Indicates G.832 ADM mode e3g751adm : Indicates G.751 ADM mode e3g751plcp : Indicates G.751 PLCP mode e3Framed : Refer CCITT G.751 [12] e3Plcp : Refer ETSI T/NA(91)19 [14] e3g832frmronly : Indicates G.832 FRAMER-ONLY mode e3g751frmronly : Indicates G.751 FRAMER-ONLY mode.

cds3LineAIScBitsCheckINTEGERread-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.2

When check(1) is set, then Alarm Indication Signal (AIS) is declared when '1010...'b is found and C-Bits are all zero. When ignore(2) is set, an AIS condition is declared when the '1010...'b is detected irrespective of the state of the C-Bits. Does not apply to the E3 interface.

cds3LineRcvFEACValidationINTEGERread-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.3

This entry specifies the FEAC (Far End Alarm and Control) code validation criteria. If 'fEACCodes4Of5' is specified, then a valid FEAC code is declared if 4 of 5 codes match. When 'fEACCodes8Of10' is specified, then a valid FEAC code is declared when 8 of 10 codes match. If disable(3) is specified, then FEAC code generation and detection is disabled. Does not apply to the E3 interface.

cds3LineOOFCriteriaINTEGERread-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.4

This entry specifies the out of frame(OOF) decision criteria. If 'bits3Of8' is specified then an OOF condition is declared if at least 3 of 8 framing bits are in error. When 'bits3Of16' is specified then OOF is declared if 3 of 16 framing bits are found to be in error. OOF is declared when errors are detected in the framing octets for four consecutive frames. This object does not apply to E3 interface.

cds3TraceToTransmitDisplayString(SIZE(1..16))read-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.5

Transmitted G.832 Trail Trace string.

cds3TraceToExpectDisplayString(SIZE(1..16))read-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.6

G.832 Trail Trace string that is expected to be received from the other end.

cds3TraceAlarmINTEGERread-only
.1.3.6.1.4.1.9.9.132.1.1.1.1.7

The value of this object is set to traceFailure(2) when DS3 line receives a trace does not match the 'cds3TraceToExpect'.

cds3InternalEqualizerINTEGERread-write
.1.3.6.1.4.1.9.9.132.1.1.1.1.8

This variable indicates whether the internal equalizer is being used or bypassed. Set this value depending on the line equipment to which the receiver is attached. Possible values are : use(1) : Use the internal equalizer byPass(2) : bypass internal equalizer(use external equalizer). This option allows easy interfacing of the device into systems already utilizing the external equalizers.

cds3NearEndLineLoopbackStatusGauge(0..2147483647)read-only
.1.3.6.1.4.1.9.9.132.1.1.1.1.9

Indicates the loopback status of the near end DS1 on this DS3 when loopback request is indicated. Following table lists the mapping of Bit position to DS1 or DS3 lines and the value. Bit Position Line number value 0 DS3 Line 0 = no loop(loop down) 1 = loop(loop up) 1 DS1 line 1 0 = loop down 1 = loop up 2 DS1 line 2 0 = loop down 1 = loop up 3 DS1 line 3 0 = loop down 1 = loop up ... ... 28 DS1 line 28 0 = loop down 1 = loop up 29 all DS1 lines 0 = loop up 1 = loop down

cds3FarEndLineLoopbackStatusGauge(0..2147483647)read-only
.1.3.6.1.4.1.9.9.132.1.1.1.1.10

Indicates the loopback status of the far end DS3,DS1 when remote DS1 loopback request is initiated. The remote DS1 loopback is initiated by setting dsx3SendCode object to dsx3SendDS1LoopCode(5). For unchannelized DS3 applications DS1s are unassigned. Following table lists the mapping of Bit position to DS1 or DS3 lines and the value. Bit Position Line number value 0 DS3 Line 0 = line loopback activate 1 = line loopback deactivate 1 DS1 line 1 0 = loop down 1 = loop up 2 DS1 line 2 0 = loop down 1 = loop up 3 DS1 line 3 0 = loop down 1 = loop up ... ... 28 DS1 line 29 0 = loop down 1 = loop up 29 all DS1 lines 0 = loop down 1 = loop up

cds3AlarmConfigEntryCds3AlarmConfigEntrynot-accessible
.1.3.6.1.4.1.9.9.132.1.2.1.1.1

An entry in the T3/E3 Alarm Configuration Table. The entries are automatically created for an ifType value of 'ds3'(30), with default values for objects. Thresholds may be configured for: Line Code Violations(LCV), LineErrored Seconds(LES), Line Severely Errored Seconds(LSES), P-bit Coding Violations(PCV), P-bit Errored Seconds(PES), P-bit Severely Errored Seconds(PSES), Severely Errored Seconds(SES), Severely Errored Framing Seconds(SEFS), Unavailable Seconds(UAS), C-bit coding violations(CCV), C-bit errored seconds(CES), C-bit errored seconds(CSES). Once these thresholds are exceeded, minor or major alarms are raised. Please refer to RFC2496 for descriptions of these errors.

cds3NEAlarmUpCountGauge(0..2147483647)read-write
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.1

This parameter specifies the increment to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 6 and the integration counter is incremented by this value every 10 ms while the alarm persists. The counter is decremented by the value of 'cds3NEAlarmDownCount' while there is no alarm (the counter does not decrement below zero). When the integration counter exceeds 'cds3NEAlarmThreshold' an Alarm of the severity specified for the particular Near End alarm is declared.

cds3NEAlarmDownCountGauge(0..2147483647)read-write
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.2

This parameter specifies the decrement to the Near End alarm integration counters. The alarms are LOS and LOF. The Default value is 1 and the integration counter is decremented by this value every 10 ms while no alarm persists. The counter is incremented by the value of cds3NEAlarmUpCount while there is no alarm (the counter does not decrement below zero). When the integration counter reaches zero any Alarm previously declared is removed.

cds3NEAlarmThresholdGauge(0..2147483647)read-write
.1.3.6.1.4.1.9.9.132.1.2.1.1.1.3

The value set in this object determines the value that the alarm integration counter must reach for an near end alarm to be declared. If the up count is 6, and the threshold 150, an Alarm is integrated in 2.5 seconds. If the down count is 1, then alarm will be cleared in 15 seconds.

More MIBs from Cisco

Browse all CiscoMIBs →
CISCO-UNIFIED-COMPUTING-COMPUTE-MIB

The CISCO-UNIFIED-COMPUTING-COMPUTE-MIB provides SNMP-based monitoring and management of Cisco UCS compute blades, servers, and chassis components, exposing critical metrics such as CPU utilization, memory usage, thermal sensor readings, power supply status, and interface operational states. This module enables granular visibility into the health and performance of the Cisco Unified Computing System's compute subsystems for capacity planning and fault isolation.

1401 objects→
CISCO-UNIFIED-COMPUTING-STORAGE-MIB

The CISCO-UNIFIED-COMPUTING-STORAGE-MIB facilitates SNMP-based monitoring and management of storage subsystems, including Fibre Channel and iSCSI interfaces, within the Cisco Unified Computing System (UCS) fabric interconnects and blade servers. It exposes critical operational metrics such as port status, error counters, throughput statistics, and storage controller health states to enable granular visibility into the storage infrastructure.

1295 objects→
CISCO-UNIFIED-COMPUTING-VNIC-MIB

The CISCO-UNIFIED-COMPUTING-VNIC-MIB enables SNMP-based monitoring and management of Virtual Network Interface Card (vNIC) attributes, including operational status, traffic counters, and binding configurations, within the Cisco Unified Computing System (UCS) fabric interconnects and server blades.

1161 objects→
CERENT-GENERIC-MIB

SNMP MIB module

984 objects→
CISCO-UNIFIED-COMPUTING-BIOS-MIB

The CISCO-UNIFIED-COMPUTING-BIOS-MIB enables SNMP-based monitoring and configuration of BIOS-level parameters, firmware versions, and hardware initialization states within Cisco Unified Computing System (UCS) servers. It provides visibility into critical server boot diagnostics, BIOS settings, and hardware readiness indicators to facilitate low-level infrastructure management and troubleshooting.

937 objects→
CISCO-UNIFIED-COMPUTING-ETHER-MIB

The CISCO-UNIFIED-COMPUTING-ETHER-MIB provides SNMP management interfaces for monitoring Ethernet interface statistics, link states, and error counters on Cisco Unified Computing System (UCS) fabric interconnects and blade server line cards. This module enables the tracking of physical layer connectivity, port throughput, and packet error rates within the UCS Ethernet switching infrastructure.

920 objects→