CISCO-CAS-IF-MIB
AI MIB Summary
The CISCO-CAS-IF-MIB monitors and manages Channel Associated Signaling (CAS) and DS0 clear channel interfaces on Cisco routers, tracking operational status, traffic counters, and signal states for legacy T1/E1 voice circuits.
Channel Associated Signal Interface MIB module. This MIB manages the generic CAS (Channel Associated Signal)or DS0 clear channel Interfaces in the router.
109
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
109 total| Object Name |
|---|
ciscoCasIfMIB OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85 |
CISCO-SMI Unknown .1.3.6.1.4.1.9.9.85 |
ccasIfObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1 |
ccasDS1Objects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.1 |
ccasDs1IfCfgTableThe CAS/DS0 General Configuration Table for T1/E1. It
contains the CAS/DS0 related standard configuration
information for T1/E1. SEQUENCE OF CcasDs1IfCfgEntry .1.3.6.1.4.1.9.9.85.1.1.1 |
ccasDs1IfCfgEntryAn entry in the configuration table for each T1/E1.
The entry is created when a T1/E1 hardware is detected. CcasDs1IfCfgEntry .1.3.6.1.4.1.9.9.85.1.1.1.1 |
ccasDs1IfCfgDs0ChannelsConfigurableThis object contains the bit map of the avaliable DS0
channel in the DS1.
The MSB (most significant bit) is DS0 channel number 1.
The missing bytes is default to a value of 0.
A 1-bit indicates the channel is available for
configuration and a 0-bit indicates it isn't.
The length of this object is either 3 octets (for T1)
or 4 octets (for E1).
The most significant bit is transmitted first.ro OCTET STRING .1.3.6.1.4.1.9.9.85.1.1.1.1.1 |
ccasGrpObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2 |
ccasGrpGeneralObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2.1 |
ccasGrpCfgTableThe CAS/DS0 Group Standard Configuration Table. It
contains the general configuration information for the
CAS/DS0 group of T1/E1 interfaces. SEQUENCE OF CcasGrpCfgEntry .1.3.6.1.4.1.9.9.85.1.2.1.1 |
ccasGrpCfgEntryA CAS/DS0 group entry. Each entry consists of the CAS
group type and the CAS/DS0 group associated DS0
channels in a T1/E1.
The value of ccasGrpCfgDs0Channels must be specified
with at least one available DS0 channel in the CAS
group associated T1/E1 before a new row in this table
can become active(1).
The entry of this table can only be created if the
CAS/DS0 group associated DS1 ifEntry already exists. CcasGrpCfgEntry .1.3.6.1.4.1.9.9.85.1.2.1.1.1 |
ccasGrpCfgIndexAn arbitrary index that uniquely identifies a DS0 group
in a T1/E1. INTEGER .1.3.6.1.4.1.9.9.85.1.2.1.1.1.1 |
ccasGrpCfgTypeThe Signaling type of the DS0 group.
emWinkStart - CAS E&M Wink Start.
emWinkStartFgd - CAS E&M Wink Start with Feature
group D.
emImmedStart - CAS E&M Immediate Start.
emDelayDial - CAS E&M Delay Dial.
fxsLoopStart - CAS FXS Loop Start.
fxsGroundStart - CAS FXS Ground Start.
sasLoopStart - CAS SAS Loop Start.
sasGroundStart - CAS SAS Ground Start.
r2Analog - R2 ITU Q411.
r2Digital - R2 ITU Q421.
r2Pulse - R2 ITU Supplement 7.
p7 - P7 switch.
fgdOS - Bellcore Feature Group D :
Operator Services Signaling
nullSignaling - 64k clear channel
r1Itu - R1 ITU.
r1Modified - R1 Modified.
r1Turkey - R1 Turkey.
fgdEANA - FGD Exchange Access North American.rw Enumeration .1.3.6.1.4.1.9.9.85.1.2.1.1.1.2 |
ccasGrpCfgDs0ChannelsThis object contains the bit map of the selected DS0
channels to be added into this group.
The MSB (most significant bit) is DS0 channel number 1.
For T1, only higher 24 bits are used to specify the
the CAS channels for the CAS group.
A 1-bit indicates the channel to be added into group
and a 0-bit indicates it isn't.rw OCTET STRING .1.3.6.1.4.1.9.9.85.1.2.1.1.1.3 |
ccasGrpCfgRowStatusThis object is used to create a new row or modify
or delete an existing row in this table. The
corresponding instance of ccasGrpCfgType can not be
modified while this object has the value 'active'.rw RowStatus -- Rsyntax INTEGER { -- active(1), -- notInService(2), -- notReady(3), -- createAndGo(4), -- createAndWait(5), -- destroy(6) -- } .1.3.6.1.4.1.9.9.85.1.2.1.1.1.4 |
ccasGrpCfgServiceTypeSpecify the Service type of the CAS/DS0 group.
none - no service type
casServSw56 - sw56 service for CAS
casServModme - modem service for CAS
casServAuto - auto service for CAS
sgcp - Simple Gateway Control Protocol
(SGCP) service. Used when DS0 is
configured for null signaling.
mgcp - Media Gateway Control Protocol
(MGCP) service. Used when DS0 is
configured for null signaling.
other - none of the above.rw Enumeration .1.3.6.1.4.1.9.9.85.1.2.1.1.1.5 |
ccasGrpEMObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2.2 |
ccasGrpEMCfgTableThe CAS Group E&M Standard Configuration Table. It
contains the CAS E&M group standard configuration
information of T1/E1. SEQUENCE OF CcasGrpEMCfgEntry .1.3.6.1.4.1.9.9.85.1.2.2.1 |
ccasGrpEMCfgEntryAn entry in the configuration table for each CAS E&M
Group in the T1/E1.
The entry is created when the ccasGrpCfgType is
configured as 'em' on a T1/E1 via configuration
command.
The entry is deleted when the CAS Group is
de-configured from T1/E1. CcasGrpEMCfgEntry .1.3.6.1.4.1.9.9.85.1.2.2.1.1 |
ccasGrpEMCfgDialTypeSpecify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
mf - Multi-Frequency (MF) digit.
The default value of this object is dtmf(1).rw Enumeration .1.3.6.1.4.1.9.9.85.1.2.2.1.1.1 |
ccasGrpEMCfgDnisAniSpecify the type of Destination Number Identification
Service (DNIS) and Automatic Number Identification
(ANI) support.
MF tone supports both ANI and DNIS services. The DTMF
tone only supports both incoming and outgoing DNIS.
incomingDnis - support incoming DNIS feature.
incomingAni - support incoming ANI feature.
outgoingDnis - support outgoing DNIS feature.
outgoingAni - support outgoing ANI feature.
The default value of this object is '00'H.rw OCTET STRING .1.3.6.1.4.1.9.9.85.1.2.2.1.1.2 |
ccasGrpEMTmTableThe E&M interface Timing Parameters table. It
contains the configuration of the various E&M signaling
protocol timing parameters. SEQUENCE OF CcasGrpEMTmEntry .1.3.6.1.4.1.9.9.85.1.2.2.2 |
ccasGrpEMTmEntryAn entry in the E&M Timing Parameters Table for
each E&M interface. CcasGrpEMTmEntry .1.3.6.1.4.1.9.9.85.1.2.2.2.1 |
ccasGrpEMTmClearWaitDurationTime of Inactive incoming seizure signal to declare call
cleared.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emWinkStart(1) or
emWinkStartFgd(2).
The default value of this object is 400 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.1 |
ccasGrpEMTmMaxWinkWaitDurationMaximum wink wait duration for sending out wink start
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object
is emWinkStart(1) or emWinkStartFgd(2).
The default value of this object is 200 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.2 |
ccasGrpEMTmMaxWinkDurationMaximum wink duration for sending out wink start
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emWinkStart(1)
or emWinkStartFgd(2).
The default value of this object is 200 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.3 |
ccasGrpEMTmDelayStartTiming of generation of outgoing delayed start signal
from detection of incoming seizure.
This object is relevant to the interfaces of the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 300 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.4 |
ccasGrpEMTmMaxDelayDurationMaximum delay signal duration for sending out delay dial
signaling.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 2000 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.5 |
ccasGrpEMTmMinDelayPulseWidthMinimum delay-dial pulse duration for incoming call.
If the value of this object is 0, then no delay-dial
is sent to the far end for the incoming call.
This object is relevant to the interfaces in the CAS
group if the ccasGrpCfgType object is emDelayDial(4).
The default value of this object is 140 milliseconds.rw INTEGER(0|140..5000) -- Units -- milliseconds .1.3.6.1.4.1.9.9.85.1.2.2.2.1.6 |
ccasGrpEMTmDigitDurationOutgoing DTMF/MF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpCfgDialType
is dtmf or R2 tone.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.7 |
ccasGrpEMTmInterDigitDurationOutgoing DTMF/MF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpCfgDialType
is dtmf or R2 tone.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.8 |
ccasGrpEMTmPulseRateOutgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpCfgDialType
is pulse.
The default value of this object is 10 pps.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.9 |
ccasGrpEMTmPulseInterDigitDurationOutgoing Pulse dialing inter-digit timing in
milliseconds.
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpCfgDialType
is pulse.
The default value of this object is 500 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.2.2.1.10 |
ccasGrpLineObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2.3 |
ccasGrpLineCfgTableThe CAS Group FXS/SAS Standard Configuration Table. It
contains the CAS FXS/SAS group standard configuration
information of T1/E1. SEQUENCE OF CcasGrpLineCfgEntry .1.3.6.1.4.1.9.9.85.1.2.3.1 |
ccasGrpLineCfgEntryAn entry in the configuration table for each CAS
FXS/SAS Group in the T1/E1.
The entry is created when the ccasGrpCfgType is
configured as 'fxs' or 'sas' on a T1/E1 via
configuration command. The entry is deleted when the
CAS Group is de-configured from T1/E1. CcasGrpLineCfgEntry .1.3.6.1.4.1.9.9.85.1.2.3.1.1 |
ccasGrpLineCfgNumberRingsThe number of rings detected before closing loop.
If the value of this object is 0, then the managed
system answers immediately after the interface detects
a incoming seizure if the ccasGrpCfgType is
'fxsGroundStart' or 'sasGroundStart'.
The default value of this object is 1 ring.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.3.1.1.1 |
ccasGrpLineCfgSupDisconnectSpecifies whether a supervisory disconnect signal will
be presented to the interface when the connected party
at the interface hangs up. this object is only relevent
to the ccasGrpCfgType is fxsLoopStart or sasLoopStart.
The default value of this object is 'true'.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.2.3.1.1.2 |
ccasGrpLineCfgDialTypeSpecify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
The default value of this object is dtmf(1).rw Enumeration .1.3.6.1.4.1.9.9.85.1.2.3.1.1.3 |
ccasGrpLineTmTableThe FXS/SAS interface Timing Parameters table. It
contains the configuration of the various FXS/SAS
signaling protocol timing parameters. SEQUENCE OF CcasGrpLineTmEntry .1.3.6.1.4.1.9.9.85.1.2.3.2 |
ccasGrpLineTmEntryAn entry in the FXS/SAS Timing Parameters Table for
each FXS/SAS interface. CcasGrpLineTmEntry .1.3.6.1.4.1.9.9.85.1.2.3.2.1 |
ccasGrpLineTmDigitDurationOutgoing DTMF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpLineCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.3.2.1.1 |
ccasGrpLineTmInterDigitDurationOutgoing DTMF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing
of the interfaces in the CAS group if
ccasGrpLineCfgDialType is dtmf.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.3.2.1.2 |
ccasGrpLineTmPulseRateOutgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpStaCfgDialType
is pulse.
The default value of this object is 10 pps.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.3.2.1.3 |
ccasGrpLineTmPulseInterDigitDurationOutgoing Pulse dialing inter-digit timing in
milliseconds. This object is relevant to the addressing
timing of the interfaces in the CAS group only if
ccasGrpStaCfgDialType is pulse.
The default value of this object is 500 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.3.2.1.4 |
ccasGrpStaObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2.4 |
ccasGrpStaCfgTableThe FXO/SAO standard configuration table. It contains
FXO/SAO configuration parameters, one entry per FXO/SAO
interface.
The configuration information of this table is set by
its default setting when the CAS group is created by
the configuration commands. SEQUENCE OF CcasGrpStaCfgEntry .1.3.6.1.4.1.9.9.85.1.2.4.1 |
ccasGrpStaCfgEntryAn entry in the standard configuration table for
each FXO/SAO Group.
The entry is created when the ccasGrpCfgType is
configured as 'fxo' or 'sao' on a T1/E1 via
configuration command. The entry is deleted when the
CAS Group is de-configured from T1/E1. CcasGrpStaCfgEntry .1.3.6.1.4.1.9.9.85.1.2.4.1.1 |
ccasGrpStaCfgNumberRingsThe number of rings sent before sending reorder to the
originator and releasing resources.
If the value of this object is 0, then sending
reorder to the originator is disabled.
The default value of this object is 20 rings.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.4.1.1.1 |
ccasGrpStaCfgDialTypeSpecify the addressing type of the CAS group.
dtmf - Dual Tone Multi-Frequency (DTMF) digit.
pulse - dial pulse.
The default value of this object is dtmf(1).rw Enumeration .1.3.6.1.4.1.9.9.85.1.2.4.1.1.2 |
ccasGrpStaTmTableThe FXO/SAO interface Timing Parameters table. It
contains the configuration of the various FXO/SAO
signaling protocol timing parameters. SEQUENCE OF CcasGrpStaTmEntry .1.3.6.1.4.1.9.9.85.1.2.4.2 |
ccasGrpStaTmEntryAn entry in the FXO/SAO Timing Parameters Table for
each FXO/SAO interface. CcasGrpStaTmEntry .1.3.6.1.4.1.9.9.85.1.2.4.2.1 |
ccasGrpStaTmDigitDurationOutgoing DTMF digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpStaCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.4.2.1.1 |
ccasGrpStaTmInterDigitDurationOutgoing DTMF inter-digit duration in milliseconds.
This object is not relevant to the addressing timing of
the interfaces in the CAS group if ccasGrpStaCfgDialType
is dtmf.
The default value of this object is 100 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.4.2.1.2 |
ccasGrpStaTmPulseRateOutgoing Pulse dialing rate in pulses per second (pps).
This object is relevant to the addressing timing of the
interfaces in the CAS group only if ccasGrpStaCfgDialType
is pulse.
The default value of this object is 10 pps.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.4.2.1.3 |
ccasGrpStaTmPulseInterDigitDurationOutgoing Pulse dialing inter-digit timing in
milliseconds. This object is relevant to the addressing
timing of the interfaces in the CAS group only if
ccasGrpStaCfgDialType is pulse.
The default value of this object is 500 milliseconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.2.4.2.1.4 |
ccasGrpABCDObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.2.5 |
ccasGrpABCDCfgTableThe CAS group custom ABCD bits configuration table for
E1. It contains A/B/C/D bits handling objects, one
entry per CAS group on an E1 interface. SEQUENCE OF CcasGrpABCDCfgEntry .1.3.6.1.4.1.9.9.85.1.2.5.1 |
ccasGrpABCDCfgEntryAn entry in the custom ABCD configuration table for
each CAS Group on an E1 interface.
The entry is created when a CAS group is configured
on a E1. The entry is deleted when the CAS Group is
de-configured from E1. CcasGrpABCDCfgEntry .1.3.6.1.4.1.9.9.85.1.2.5.1.1 |
ccasGrpABCDCfgInvertBitsSpecify the A/B/C/D bit mask to invert the A/B/C/D bits
value before the A/B/C/D bits are sent or
after the A/B/C/D bits are received.
1-bit - enable bit invertion.
0-bit - disable bit invertion.
The default value of this object is '00'Hrw OCTET STRING .1.3.6.1.4.1.9.9.85.1.2.5.1.1.1 |
ccasGrpABCDCfgUnusedBitsSpecify the Unused A/B/C/D bit values to transmit.
If any A/B/C/D bit is unused, the bit values in this
object will be used to transmit for the unused
A/B/C/D bits.
The default value of this object is '00'Hrw OCTET STRING .1.3.6.1.4.1.9.9.85.1.2.5.1.1.2 |
ccasChannelObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.3 |
ccasChannelCfgTableThe CAS channel Standard Configuration Table. It
contains the standard configuration information of CAS
channel of T1/E1. SEQUENCE OF CcasChannelCfgEntry .1.3.6.1.4.1.9.9.85.1.3.1 |
ccasChannelCfgEntryAn entry in the configuration table for each CAS
channel. The entry is created when a CAS channel is
configured on a T1/E1 via configuration command. The
entry is deleted when the CAS channel is de-configured
from T1/E1. CcasChannelCfgEntry .1.3.6.1.4.1.9.9.85.1.3.1.1 |
ccasChannelCfgDS1IfIndexthe ifIndex of this CAS channel associated T1/E1.ro InterfaceIndex -- Rsyntax INTEGER .1.3.6.1.4.1.9.9.85.1.3.1.1.1 |
ccasChannelCfgGroupThe CAS channel associated CAS group number.ro INTEGER .1.3.6.1.4.1.9.9.85.1.3.1.1.2 |
ccasChannelCfgTimeSlotThe CAS channel associated T1/E1 timeslot.ro INTEGER .1.3.6.1.4.1.9.9.85.1.3.1.1.3 |
ccasChannelCfgBusyOutThe CAS channel busyout configurstion.
true - the CAS channel is busied out.
false - the CAS is normal.
The default value for this object is 'false'.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.3.1.1.4 |
ccasChannelStatusTableThe CAS channel Status Table. It contains general
information about the status of CAS channel. SEQUENCE OF CcasChannelStatusEntry .1.3.6.1.4.1.9.9.85.1.3.2 |
ccasChannelStatusEntryAn entry in the status table for each CAS channel. CcasChannelStatusEntry .1.3.6.1.4.1.9.9.85.1.3.2.1 |
ccasChannelStatusRecvSignalBitsThe receive ABCD signaling bits for the CAS channel.
aBit - the signaling bit in the 6th frame
bBit - the signaling bit in the 12th frame
cBit - the signaling bit in the 18th frame
dBit - the signaling bit in the 24th frame
the cBit and dBit are only valid for E1 or T1
interface is operating in extended superframe (ESF)
mode.ro OCTET STRING .1.3.6.1.4.1.9.9.85.1.3.2.1.1 |
ccasChannelStatusBusyOutThe CAS channel busyout state.
true - the CAS channel is busied out.
false - the CAS is normal.ro TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.3.2.1.2 |
ccasChannelStatusInfoTypeThe Information Transfer Capability for the current
or last call.
unknown - If since system startup there has been no call
on this interface, this object has a value of
unknown(1).
speech - refers to a non-data connection
data56 - 56k data.
audio31 - audio 3.1 kHz; refers to data mode connections
audio7 - audio 7 kHz; refer to data mode connections;
'Unrestricted digital information with tones/
announcements'.
video - as defined in Q.931
fax - Facsimile
modem - V.3x modemro Enumeration .1.3.6.1.4.1.9.9.85.1.3.2.1.3 |
ccasChannelStatusXmitSignalBitsThe transmit ABCD signaling bits for the CAS channel.
aBit - the signaling bit in the 6th frame
bBit - the signaling bit in the 12th frame
cBit - the signaling bit in the 18th frame
dBit - the signaling bit in the 24th frame
the cBit and dBit are only valid for E1 or T1
interface is operating in extended superframe (ESF)
mode.ro OCTET STRING .1.3.6.1.4.1.9.9.85.1.3.2.1.4 |
ccasVoiceCfgObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.4 |
ccasVoiceCfgTableThe voice specific configuration Table. It contains
information about the voice related configuration
parameters for a CAS group. SEQUENCE OF CcasVoiceCfgEntry .1.3.6.1.4.1.9.9.85.1.4.1 |
ccasVoiceCfgEntryAn entry in the voice specific configuration table for each
CAS/DS0 group of a DS1.
The entry is created if the associated CAS/DS0 group is
created and the voice hardware is detected to support the
voice capability for the CAS/DS0 group in the managed
system.
The entry is deleted when its associated CAS/DS0 group is
deleted. CcasVoiceCfgEntry .1.3.6.1.4.1.9.9.85.1.4.1.1 |
ccasVoiceCfgNoiseRegEnableThe object indicates whether or not the background noise
should be played to fill silence gaps if VAD is activated.
The default value of this object is 'true'.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.4.1.1.1 |
ccasVoiceCfgNonLinearProcEnableThe object indicates whether or not the Nonlinear Processing
is enabled for the interface.
The default value of this object is 'true'.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.4.1.1.2 |
ccasVoiceCfgMusicOnHoldThresholdThe object specifies the Music On Hold Threshold for
the interface.
The default value of this object is -38 dBm.rw INTEGER(-70..-30) -- Units -- dBm .1.3.6.1.4.1.9.9.85.1.4.1.1.3 |
ccasVoiceCfgInGainThis object contains the amount of gain inserted at the
receiver side of the interface. The input gain settings
only define a gain/loss relative to the 0 dB setting.
The absolute loss at the 0 dB setting could be
implementation dependent based on the desired network
loss plan.
The default value of this object is 0 dB (decibel).rw INTEGER(-6..14) -- Units -- dB .1.3.6.1.4.1.9.9.85.1.4.1.1.4 |
ccasVoiceCfgOutAttnThis object contains the amount of attenuation inserted
at the transmit side of the interface.
The output attenuation settings only define a loss
relative to the 0 dB setting.
The absolute loss at the 0 dB setting could be
implementation dependent based on the desired network
loss plan.
The default value of this object is 0 dB (decibel).rw INTEGER .1.3.6.1.4.1.9.9.85.1.4.1.1.5 |
ccasVoiceCfgEchoCancelEnableThe object specifies whether or not the Echo Cancellation
is enabled for the interface.
The default value of this object is 'true'.rw TruthValue -- Rsyntax INTEGER { -- true(1), -- false(2) -- } .1.3.6.1.4.1.9.9.85.1.4.1.1.6 |
ccasVoiceCfgEchoCancelCoverageThe object specifies the Echo Canceller coverage for
the interface. This object is valid if the
ccasVoiceCfgEchoCancelEnable object is 'true'.
echoCanceller8ms - 8 milliseconds echo canceller coverage.
echoCanceller16ms - 16 milliseconds echo canceller coverage.
echoCanceller24ms - 24 milliseconds echo canceller coverage.
echoCanceller32ms - 32 milliseconds echo canceller coverage.
echoCanceller64ms -
64 milliseconds echo canceller coverage.
echoCanceller128ms-
128 milliseconds echo canceller coverage.
The default value of this object is echoCanceller8ms.rw Enumeration .1.3.6.1.4.1.9.9.85.1.4.1.1.7 |
ccasVoiceCfgConnectionModeThe object indicates the connection mode of the interface.
normal - the interface acts normally to handle incoming
and outgoing call.
trunk - the interface acts in trunking mode. trunking mode
causes two interfaces (on either the same or
different routers) to be always conferenced
together, and for telephony signaling to be
passed transparently through the VoIP system
rather than trapped and interpreted by the session
application on the router(s).
plar - the interface acts in PLAR (private line automatic
ringdown) mode. PLAR is handled by associating a
peer directly with an interface such that when the
interface goes off-hook, that peer is used to setup
the second call leg and conference them together
without the caller having to dial any digits.rw Enumeration .1.3.6.1.4.1.9.9.85.1.4.1.1.8 |
ccasVoiceCfgConnectionNumberThis is the E.164 phone number that is used to
establish connection with trunking mode or PLAR mode.
If the ccasVoiceCfgConnectionMode is 'normal', then this
object will be a zero length string.rw DisplayString .1.3.6.1.4.1.9.9.85.1.4.1.1.9 |
ccasVoiceCfgInitialDigitTimeOutThis is the initial digit timeout that indicates the amount
of time the managed system waits for an initial input digit
from the caller. The timer is activated when the call is
accepted and is deactivated upon digit input. If the timer
expires, the caller is signaled through the appropriate
tone and the call is abandoned. The value of zero disables
the timer.
The default value of this object is 10 seconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.4.1.1.10 |
ccasVoiceCfgInterDigitTimeOutThis is the inter-digit timeout that indicates the amount
of time the managed system waits for a subsequent input
digit from the caller. The timer is started upon receipt of
an input digit and restarted as each digit is received
until the destination address is identified. If the timer
expires and no destination address is identified, the
caller is signaled through the appropriate tone and the
call is abandoned. The value of zero disables the timer.
The default value of this object is 10 seconds.rw INTEGER .1.3.6.1.4.1.9.9.85.1.4.1.1.11 |
ccasVoiceCfgRegionalToneThis object contains the current regional setting for
the call progress tone to be used by this CAS group.rw CountryCode -- Rsyntax OCTET STRING .1.3.6.1.4.1.9.9.85.1.4.1.1.12 |
ccasXgcpCfgObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.1.5 |
ccasXgcpCfgTableThe XGCP configuration Table contains
information about DS0 usage by XGCP(SGCP/MGCP).
XGCP is meant to represent both Simple Gateway Control
Protocol (SGCP) and Media Gateway Control Protocol (MGCP). SEQUENCE OF CcasXgcpCfgEntry .1.3.6.1.4.1.9.9.85.1.5.1 |
ccasXgcpCfgEntryAn entry in the configuration table for each
DS0 group of a DS1.
The entry is created if the DS0 group is configured as
null-signaling and ccasGrpCfgServiceType is configured
as either sgcp or mgcp.
The entry is deleted when the signaling type is configured
as non null-signaling. CcasXgcpCfgEntry .1.3.6.1.4.1.9.9.85.1.5.1.1 |
ccasXgcpCfgCotToneCo1This object specifies the continuity test tone
frequencies for co1. Co1 is the COT tone freqency from
the terminating switch in transponder mode and is from
the originating switch in loopback mode.rw INTEGER .1.3.6.1.4.1.9.9.85.1.5.1.1.1 |
ccasXgcpCfgCotToneCo2This object specifies the continuity test tone
frequencies for co2. Co2 is the COT tone freqency from
the originating switch only in transponder mode.rw INTEGER .1.3.6.1.4.1.9.9.85.1.5.1.1.2 |
ccasIfMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3 |
ccasIfMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.1 |
ccasIfMIBCompliance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.1.1 |
ccasIfMIBComplianceRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.1.2 |
ccasIfMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2 |
ccasIfDS1Group OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.1 |
ccasGeneralInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.2 |
ccasEMGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.3 |
ccasLineGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.4 |
ccasStaGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.5 |
ccasCustomABCDGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.6 |
ccasVoiceGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.7 |
ccasGeneralInfoGroupRev1 OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.8 |
ccasChannelInfoGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.9 |
ccasXgcpCfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.85.3.2.10 |