CISCO-ATM-TRAFFIC-MIB
AI MIB Summary
The CISCO-ATM-TRAFFIC-MIB monitors and manages traffic statistics for Cisco ATM interfaces by extending RFC 1695 OIDs to track cell counts, byte volumes, and discard rates. This module enables precise performance analysis of Asynchronous Transfer Mode networks by providing granular visibility into ATM-specific traffic flows and interface utilization metrics.
This MIB module is an extension to traffic OIDs and variables defined in rfc1695.
Main OID:
ciscoAtmTrafficExtMIB.1.3.6.1.4.1.9.10.11
17
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
17 total| Object Name |
|---|
ciscoAtmTrafficExtMIBThis MIB module is an extension to traffic OIDs
and variables defined in rfc1695. MODULE-IDENTITY .1.3.6.1.4.1.9.10.11 |
ciscoAtmTrafficExtMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1 |
ciscoAtmTrafficTypeExt OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1 |
atmNoClpNoScrCdvtSpecifies peak cell rate for CLP, and
cell delay variation tolerance:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CDVT in cell-times
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor is for cbr, abr
or ubr service categories, desiring to
specify the cdvt as well as pcr. OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1.1 |
atmClpScrMbsCdvtThis traffic descriptor is for Peak
Cell Rate (PCR), Sustained Cell Rate (SCR),
Maximum Burst Size applied to SCR,
and Cell Delay Variation Tolerance
applied to PCR.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 sustained cell rate in
cells per second.
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in cell-times
Parameter 5: not used. OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1.2 |
atmNoClpScrMbsCdvtThis traffic descriptor is for Peak
Cell Rate (PCR), Sustained Cell Rate (SCR),
Maximum Burst Size applied to SCR,
and Cell Delay Variation Tolerance
applied to PCR.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0+1 sustained cell rate in
cells per second.
Parameter 3: maximum burst size in cells
Parameter 4: CDVT in cell-times
Parameter 5: not used. OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1.3 |
atmNoClpMcrThis traffic descriptor is for Peak
Cell Rate (PCR) and Minimum Cell Rate
(MCR).
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0+1 minimum cell rate in
cells per second.
Parameter 3: not used.
Parameter 4: not used.
Parameter 5: not used. OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1.4 |
atmNoClpMcrCdvtThis traffic descriptor is for Peak
Cell Rate (PCR), Minimum Cell Rate (MCR),
and Cell Delay Variation Tolerance
applied to PCR.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CDVT in cell-times
Parameter 3: CLP=0+1 minimum cell rate in
cells per second.
Parameter 4: not used.
Parameter 5: not used. OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.1.5 |
ciscoAtmTrafficTableExt OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.1.2 |
atmTrafficDescrParamExtTableProvide additional information specifying traffic parameters
for a VC/VP. SEQUENCE OF AtmTrafficDescrParamExtEntry .1.3.6.1.4.1.9.10.11.1.2.1 |
atmTrafficDescrParamExtEntryAn entry in the Traffic Parameter Descriptor extension
table. AtmTrafficDescrParamExtEntry .1.3.6.1.4.1.9.10.11.1.2.1.1 |
atmTrafficExplicitServCategoryThis objects indicates the Service Category
specified by the Traffic Descriptor.
If it is defined, the setting of this
object determines the Service Category used
for the connection. This then limits the
possible Traffic Descriptor Types as follows:
Explicit
Service
Category Type may only be
-
cbr atmNoClpNoScr.
atmClpNoTaggingNoScr
atmClpTaggingNoScr
atmNoClpNoScrCdvt
abr/ubr atmNoTrafficDescriptor
atmNoClpNoScr.
atmNoClpNoScrCdvt
atmNoClpMcr
atmNoClpMcrCdvt
vbr atmNoClpScr
atmClpNoTaggingScr
atmClpTaggingScr
atmClpScrMbsCdvt
atmNoClpScrMbsCdvt
-
If the settings of Service Category and Traffic
Descriptor Type are not compatible, the row can
not be made active.rw Enumeration .1.3.6.1.4.1.9.10.11.1.2.1.1.1 |
atmTrafficDerivedServCategoryThis object indicates the Service Category
derived from the Traffic Descriptor. If the
object atmTrafficExplicitServCategory has
a defined value, then this object mirrors
that value. If Explicit Service Category
has the value notDef, then this object
reflects the Service Category derived from
the Traffic Descriptor Type as follows:
Traffic Descriptor Service
Type Category
-
atmNoTrafficDescriptor ubr
atmNoClpMcr abr
atmNoClpMcrCdvt abr
atmNoClpNoScr
atmClpNoTaggingNoScr |
atmClpTaggingNoScr |
atmNoClpNoScrCdvt
atmNoClpScr
atmClpNoTaggingScr |
atmClpScrMbsCdvt |
atmNoClpScrMbsCdvt |
atmClpTaggingScr
-ro Enumeration .1.3.6.1.4.1.9.10.11.1.2.1.1.2 |
atmTrafficDescriptorNameA human readable string that contains the unique name
of this Traffic Descriptor.
This object will return a zero-length string if value is
not set.rw SnmpAdminString (SNMP-FRAMEWORK-MIB) .1.3.6.1.4.1.9.10.11.1.2.1.1.3 |
ciscoAtmTrafficExtMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.3 |
ciscoAtmTrafficExtMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.3.1 |
ciscoAtmTrafficExtMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.10.11.3.2 |