Home/Catalog/CISCO-ATM-IF-PHYS-MIB

CISCO-ATM-IF-PHYS-MIB

AI MIB Summary

The CISCO-ATM-IF-PHYS-MIB provides managed objects to monitor the physical layer status and operational state of Cisco ATM interfaces, specifically DS3, E3, DS1, E1, and SONET circuits. It enables the tracking of interface availability, signal integrity, and physical link conditions for high-speed digital transmission paths.

A minimal set of managed objects for tracking the status of DS3/E3/DS1/E1 and SONET interfaces.

Objects

Active

Status

Dependencies

Imported Objects

Objects

41 total

Object Name	Syntax	OID
ciscoAtmIfPhysMIB OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45`
SNMPv2-SMI-v1 Unknown `.1.3.6.1.4.1.9.9.45`	Unknown	`.1.3.6.1.4.1.9.9.45`
ciscoAtmIfPhysMIBObjects OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.1`
ciscoAtmIfPhysTableA table containing basic status and statistics for the physical layer of ATM interfaces. SEQUENCE OF CiscoAtmIfPhysEntry `.1.3.6.1.4.1.9.9.45.1.1`	SEQUENCE OF CiscoAtmIfPhysEntry	`.1.3.6.1.4.1.9.9.45.1.1`
ciscoAtmIfPhysEntryBasic status and statistics for the physical layer of an ATM interface. CiscoAtmIfPhysEntry `.1.3.6.1.4.1.9.9.45.1.1.1`	CiscoAtmIfPhysEntry	`.1.3.6.1.4.1.9.9.45.1.1.1`
ciscoAtmIfPhysStatusThe status of the physical interface. The value of this object is only valid when the interface's ifAdminStatus has the value 'up'. Note that some of the enumerated values are specific to a particular physical layer.ro Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.1`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.1`
ciscoAtmIfPhysSectionParityErrorsThe number of B1 (BIP) errors on the physical interface. This object is only present for SONET interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.2`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.2`
ciscoAtmIfPhysLineParityErrorsThe number of B2 (BIP) errors on the physical interface. This object is only present for SONET interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.3`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.3`
ciscoAtmIfPhysPathParityErrorsThe number of B3 (BIP) errors on the physical interface. This object is only present for SONET interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.4`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.4`
ciscoAtmIfPhysLcvErrorsThe number of Line Code Violation errors on the physical interface. This object is only present for DS3/E3/DS1/E1 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.5`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.5`
ciscoAtmIfPhysCBitParityErrorsThe number of C-bit parity violations on the physical interface. This object is only present for DS3 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.6`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.6`
ciscoAtmIfPhysPBitParityErrorsThe number of P-bit parity violations or E3 G.832 BIP-8 errors on the physical interface. This object is present only for DS3/E3 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.7`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.7`
ciscoAtmIfPhysPlcpBipViolationsThe number of PLCP BIP violations on the physical interface. This object is only present for DS3/E3/DS1/E1 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.8`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.8`
ciscoAtmIfPhysLineFebeErrorsThe number of Z2 (Line FEBE) errors on the physical interface. This object is only present for SONET interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.9`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.9`
ciscoAtmIfPhysPathFebeErrorsThe number of G1 (Path FEBE) errors on the physical interface. This object is only present for SONET interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.10`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.10`
ciscoAtmIfPhysCellPayloadScramblingThe status of whether cell payload scrambling is enabled or disabled on the physical interface.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.11`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.11`
ciscoAtmIfPhysStsStreamScramblingThe status of whether STS-stream scrambling is enabled or disabled on the physical interface.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.12`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.12`
ciscoAtmIfPhysFramingModeThe framing format present on the physical interface. 'sonet' indicates sts-3c or sts-12c format and applies only to OC-3 and OC-12 type interfaces, respectively. 'sdh' indicates stm1 or stm4 format and applies only to OC-3 and OC-12 type interfaces, respectively. 'ds3m23adm' indicates M23 ADM mode and applies only to DS3 type interfaces. 'ds3m23plcp' indicates M23 PLCP mode and applies only to DS3 type interfaces. 'ds3cbitadm' indicates C-BIT ADM mode and applies only to DS3 type interfaces. 'ds3cbitplcp' indicates C-BIT PLCP mode and applies only to DS3 type interfaces. 'e3g832adm' indicates G.832 ADM mode and applies only to E3 type interfaces. 'e3g751adm' indicates G.751 ADM mode and applies only to E3 type interfaces. 'e3g751plcp' indicates G.751 PLCP mode and applies only to E3 type interfaces. 'ds1sfadm' indicates DS1 SF ADM mode and applies only to DS1 type interfaces. 'ds1esfadm' indicates DS1 ESF ADM mode and applies only to DS1 type interfaces. 'ds1sfplcp' indicates DS1 SF PLCP mode and applies only to DS1 type interfaces. 'ds1esfplcp' indicates DS1 ESF PLCP mode and applies only to DS1 type interfaces. 'e1adm' indicates E1 ADM mode and applies only to E1 type interfaces. 'e1plcp' indicates E1 PLCP mode and applies only to E1 type interfaces. 'e1crcadm' indicates E1 CRC-4 ADM mode and applies only to E1 type interfaces. 'e1crcplcp' indicates E1 CRC-4 PLCP mode and applies only to E1 type interfaces.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.13`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.13`
ciscoAtmIfPhysLoopbackConfigThe loopback configured on the physical interface: 'noLoop' indicates no loopback is present. 'diagnosticLoop' indicates transmit data stream is looped to the receive direction. 'lineLoop' indicates receive data stream is looped to the transmit direction. 'otherLoop' indicates loopbacks that are not defined here.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.14`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.14`
ciscoAtmIfPhysLineBuildOutThe line buildout configured on the transmit signal: 'e3AllCables' applies to all cables of E3 physical interfaces. 'ds3CablesUnder225' applies to cables under 225 feet of DS3 physical interfaces. 'ds3CablesOver225' applies to cables over 225 feet of DS3 physical interfaces. 'ds1Cables0To110' applies to cables 0 to 110 feet of DS1 physical interfaces. 'ds1Cables110To220' applies to cables 110 to 220 feet of DS1 physical interfaces. 'ds1Cables220To330' applies to cables 220 to 330 feet of DS1 physical interfaces. 'ds1Cables330To440' applies to cables 330 to 440 feet of DS1 physical interfaces. 'ds1Cables440To550' applies to cables 440 to 550 feet of DS1 physical interfaces. 'ds1Cables550To660' applies to cables 550 to 660 feet of DS1 physical interfaces. 'ds1CablesOver600' applies to cables over 600 feet of DS1 physical interfaces. 'e1AllCables' applies to all cables of E1 physical interfaces.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.15`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.15`
ciscoAtmIfPhysTransmitClockSourceThe source of the tranmit clock: 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'freeRunning' indicates that a local clock source is used. 'networkDerived' indicates that recovered receive clock from another interface is used as the transmit clock source.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.16`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.16`
ciscoAtmIfPhysClockSourcePriorityThe priority of this interface if configured as a network clock source. 'notConfigured' indicates this is not configured as a network clock source.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.17`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.17`
ciscoAtmIfPhysClockSourceStatusThe network clock source status of this interface: 'notSelected' indicates this is not selected as the network clock source. 'selected' indicates this is selected as the network clock source.ro Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.18`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.18`
ciscoAtmIfPhysDS1BitErrorsThe number of bit errors (CRC-6 error in ESF mode and framing bit error in SF mode) on the physical interface. This object is only present for DS1 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.19`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.19`
ciscoAtmIfPhysE1CrcErrorsThe number of CRC errors (in CRC-4 mode) on the physical interface. This object is only present for E1 interfaces.ro Counter32 `.1.3.6.1.4.1.9.9.45.1.1.1.20`	Counter32	`.1.3.6.1.4.1.9.9.45.1.1.1.20`
ciscoAtmIfPhysLineCodeThe line coding present on the physical interface This object is only present for DS1/E1 interfaces. 'ami' indicates alternate mark inversion (AMI) line code on the DS1/E1 interface. 'b8zs' indicates B8ZS line code on the physical interface and applies only to DS1 interfaces. 'hdb3' indicates HDB3 line code on the physical interface and applies only to E1 interfaces.rw Enumeration `.1.3.6.1.4.1.9.9.45.1.1.1.21`	Enumeration	`.1.3.6.1.4.1.9.9.45.1.1.1.21`
ciscoAtmIfPhysMIBConformance OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3`
ciscoAtmIfPhysMIBCompliances OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.1`
ciscoAtmIfPhysMIBCompliance OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.1.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.1.1`
ciscoAtmIfPhysMIBCompliance2 OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.1.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.1.2`
ciscoAtmIfPhysMIBCompliance3 OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.1.3`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.1.3`
ciscoAtmIfPhysMIBGroups OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2`
ciscoAtmIfPhysMIBCommonGroup OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.1`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.1`
ciscoAtmIfPhysMIBSonetGroup OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.2`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.2`
ciscoAtmIfPhysMIBDs3E3Group OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.3`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.3`
ciscoAtmIfPhysMIBCommonGroup2 OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.4`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.4`
ciscoAtmIfPhysMIBSonetGroup2 OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.5`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.5`
ciscoAtmIfPhysMIBDs3Group OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.6`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.6`
ciscoAtmIfPhysMIBDs1E1Group OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.7`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.7`
ciscoAtmIfPhysMIBDs1Group OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.8`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.8`
ciscoAtmIfPhysMIBE1Group OBJECT IDENTIFIER `.1.3.6.1.4.1.9.9.45.3.2.9`	OBJECT IDENTIFIER	`.1.3.6.1.4.1.9.9.45.3.2.9`