CISCO-ASPP-MIB
AI MIB Summary
The CISCO-ASPP-MIB manages Cisco serial interfaces configured in passthrough mode to facilitate asynchronous polled alarm protocols (such as ADT PollSelect, VariPoll, Diebold, and Mosec) for security monitoring stations. It exposes operational status and configuration parameters for these ASPP ports, enabling the transmission and reception of asynchronous alarm blocks without performing local error checking, which is delegated to the end-station.
The ASPP MIB provides the configuration and operational information on asynchronous polled protocols such as the asynchronous security protocols that alarm monitoring companies use. The protocols are handled in passthrough mode. ASPP will handle the receiving and sending of the asychronous blocks. It will not perform any error checking. It is the responsibilty of the end-station to perform any required error recovery. A generic protocol has been created to support asychronous protocols. In some situations this doesn't work for all types since there is no alarm protocol standard. Specific vendor support has been included for the following vendor's alarm equipment and protocols:
* adplex
* adt
- PollSelect
- VariPoll
* diebold
* mdi
* mosec (mosler)
* gddb (Guang Dong Development Bank)
- This protocol is similar to Burroughs Poll/Select
The following example configuration shows how the ASPP MIB returns ASPP information, from either CISCO A or CISCO B.
Security == ASP == Cisco == IP == Cisco == ASP == Alarm control A Network B Panel station
The following entities are managed:
1) ASPP ports (serial interfaces)
The ASPP ports are identified by the interface index, and additional information about this interface can be obtained from the Cisco Serial Interface MIB.
Main OID:
ciscoAsppMIB.1.3.6.1.4.1.9.9.55
25
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
25 total| Object Name |
|---|
ciscoAsppMIBThe ASPP MIB provides the configuration and operational
information on asynchronous polled protocols such as the
asynchronous security protocols that alarm monitoring
companies use. The protocols are handled in passthrough
mode. ASPP will handle the receiving and sending of the
asychronous blocks. It will not perform any error
checking. It is the responsibilty of the end-station to
perform any required error recovery. A generic protocol
has been created to support asychronous protocols. In
some situations this doesn't work for all types since
there is no alarm protocol standard. Specific vendor
support has been included for the following vendor's
alarm equipment and protocols:
* adplex
* adt
- PollSelect
- VariPoll
* diebold
* mdi
* mosec (mosler)
* gddb (Guang Dong Development Bank)
- This protocol is similar to Burroughs Poll/Select
The following example configuration shows how the
ASPP MIB returns ASPP information, from either CISCO A
or CISCO B.
Security == ASP == Cisco == IP == Cisco == ASP == Alarm
control A Network B Panel
station
The following entities are managed:
1) ASPP ports (serial interfaces)
The ASPP ports are identified by the interface index,
and additional information about this interface can be
obtained from the Cisco Serial Interface MIB. MODULE-IDENTITY .1.3.6.1.4.1.9.9.55 |
asppObjects OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.55.1 |
asppPorts OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.55.1.1 |
asppPortTableA list of asynchronous interfaces which have been
configured to support an asynchronous security protocol
(ASP) BSTUN group. SEQUENCE OF AsppPortEntry .1.3.6.1.4.1.9.9.55.1.1.1 |
asppPortEntryCurrent ASP configuration settings for an asynchronous
port. AsppPortEntry .1.3.6.1.4.1.9.9.55.1.1.1.1 |
asppPortProtocolSpecifies type of asynchronous security protocol being
used. These protocols are implemented by individual
security alarm manufacturers. There is no standard
protocol for alarm communications over RS-232
interfaces.
asyncGeneric(5)- provides generic polled asynchronous
support
Specific vendor support has been included for the
following vendor's alarm equipment and protocols:
* adplex(1)
* ADT
- adtPollSelect(2)
- adtVariPoll(3)
* diebold(4)
* mdi(6)
* mosec(7)
- mosler equipment
* gddb(8)
- Guang Dong Development Bank
The protocol is similar to Burroughs
Poll/Select.
apos(9) - Protocol support for asynchronous POS
devices for provide credit and debit card
authorizations to an IP attached host.ro Enumeration .1.3.6.1.4.1.9.9.55.1.1.1.1.1 |
asppPortRoleSpecifies the router's protocol role.
primary(1) - Indicates we are attaching to the terminal
or alarm panel.
secondary(2) - Indicates we are attaching to the host
or alarm console..ro Enumeration .1.3.6.1.4.1.9.9.55.1.1.1.1.2 |
asppPortReceiveInterFrameTimeoutSpecifies the receive inter-frame-timeout period, used
to delimit frames. Since all the protocols are
implemented over RS-232 3-wire circuits (ie TX, RX and
GND), the only general method for start-end frame
detection is to monitor the time between received
characters. If this time period exceeds the inter-frame
timeout value, then frame end-start is detected.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.3 |
asppPortDeviceAddressOffsetSpecifies the byte offset within a frame, which
contains the device address. This is used when the
asynchronous interface is configured to use the async
generic protocol handler. Because no knowledge of the
protocol is built-in to the IOS, it must be told where
the address field lives within the frame. That way IOS
can correctly route the frames for this protocol.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.4 |
asppPortEOFCharacterSpecifies the protocol character to use to delimit
the end of a frame. The valid character is 0-255 and
256 indicates the object is not configured.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.5 |
asppPortSOFCharacterSpecifies the protocol character to use to delimit
the beginning of a frame. The valid character is 0-255
and 256 indicates the object is not configured.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.6 |
asppPortIgnoreSequenceNumberSpecifies whether the asp sequence numbers used to
synchronize aspp traffic between head-end and tail-end
routers should be ignored. This is enabled if there
isn't a one to one correlation between commands and
responses between the two routers.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.55.1.1.1.1.7 |
asppPortRspTimerSpecifies the amount of time the router will wait for a
response to a packet before retransmission.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.8 |
asppPortRxTimerSpecifies the maximum amount of time the router will
wait for a complete packet to be received. It starts
when an STX character is received.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.9 |
asppPortHostTimerSpecifies the maximum amount of time the router will
wait for a response to a terminal request from the
host. It starts when a terminal request is forwarded
to the host.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.10 |
asppPortConnectTimerSpecifies the maximum amount of time the router will
wait for the activation of the tunnel connection to the
host to complete. It starts when a terminal requests a
session with host.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.11 |
asppPortRetryCountSpecifies the maximum number of timers a packet will be
retransmitted before the connection with the terminal
will be disconnected.ro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.12 |
asppPortDelayEnqSpecifies the amount of time to wait after sending a
connect packet to the the terminal before sending the
ENQ to initiate a sessionro Integer32 .1.3.6.1.4.1.9.9.55.1.1.1.1.13 |
asppPortDisableEnqSpecifies whether sending of ENQ to initiate a session
with the terminal is disabled.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.55.1.1.1.1.14 |
asppPortSendAckSpecifies whether the router will send an ACK to
acknowledge packets.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.55.1.1.1.1.15 |
asppPortDirectSpecifies whether the line mode is direct or dialed.
If in direct the router will immediately send ENQ
without waiting for AT commandsro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.55.1.1.1.1.16 |
asppPortDCDAlwaysSpecifies whether DCD should always be asserted or
asserted only when the connection is active.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.9.9.55.1.1.1.1.17 |
asppMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.55.3 |
asppMibCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.55.3.1 |
asppMibGroups OBJECT IDENTIFIER .1.3.6.1.4.1.9.9.55.3.2 |